Antennas and Antenna Line Products CATALOGUE 2018 Trains and Buses MOBILE COMMUNICATION
Antennas andAntenna Line Products
C A T A L O G U E 2 0 1 8
Trains and Buses MOBILE COMMUNICATION
Catalogue Issue 01/2018
All data published in previous catalogue issues hereby becomes invalid.
We reserve the right to make alterations in accordance with the requirements of our customers,
therefore for binding data please check valid data sheets on our homepage: www.kathrein.com
Please check our homepage for new antenna releases which are not part of this actual catalogue.
Our products are compliant to the EU Directive RoHS as well as to other environmentally relevant regulations (e.g. REACH).
RoHS
Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001.
Who we are and what we stand forKathrein is a specialist for reliable, high-quality communication technologies.
The company is driving innovation and technology in today’s connected world. Its ability to provide solu-tions and services enables people all over the world to communicate, access information and use media, whether at home, at the office or on the road.
The business covers a broad spectrum: from mobile communication, RFID and special solutions, to satellite reception and broadcast technology, to transmission and reception systems in vehicles.
As a hidden champion and family-owned enterprise, Kathrein has been working on the technologies of tomorrow since 1919. The company takes pride in its dedicated employees and passion for customers and quality.
Our Solutions
Find out more about us at www.kathrein.com
MOBILE COMMUNICATION
BUSINESSSOLUTIONS SAT SPECIAL
COMMUNICATION BROADCAST AUTOMOTIVE
3
Type No. Frequency Range Frequency Bands*Input Connector
(Antenna / GPS Antenna)Positioning System Page
727313 87.5 – 108 MHz FM radio N female 6
K5022211**143 – 162 MHz
2 m band
N female 7
K5022212** UHF female 7
K5022221**152 – 178 MHz
N female 7
K5022222** UHF female 7
733707** 146 – 174 MHz N female 8
87010005 380 – 430 MHz1575.42 ± 1 MHz
70 cm band
N female / TNC male GPS 9
87010008 380 – 430 MHz N female 10
K7023210 406 – 428 MHz M 11 x 1 female 11
K7023230
440 – 470 MHz
M 11 x 1 female 11
K702323** M 11 x 1 female 11
K7023231** N female 11
K702021 410 – 470 MHz N female 12
725892** 410 – 430 MHz N female 13
K702121 450 – 470 MHz N female 13
741557 380 – 400 MHz870 – 960 MHz
70 cm band /mobile standards
N female 14
87010009 430 – 470 MHz870 – 960 MHz N female 15
87010006430 – 470 MHz870 – 960 MHz
1575.42 ± 1 MHzN female / TNC male GPS 16
K702061 450 – 470 MHz790 – 960 MHz N female 17
741009 870 – 960 MHz
all mobile standards
N female 18
K7021631** 876 – 960 MHz N female 19
87010007 790 – 2700 MHz N female 20
87010023 694 – 2700 MHz1575.42 ± 1 MHz N female / TNC male GPS 21
87010003 790 – 2700 MHz1575.42 ± 1 MHz N female / TNC male GPS 22
87010012 694 – 6000 MHz1558 – 1610 MHz N female / SMA female GPS, GLONASS, BEIDOU 23
87010022 694 – 6000 MHz1558 – 1610 MHz N female / N female GPS, GLONASS, BEIDOU 23
87010032 694 – 6000 MHz1581 ± 5 MHz N female / TNC male GPS, GLONASS, BEIDOU 24
87010010 1710 – 3800 MHz N female 25
87010011 1710 – 3800 MHz1575.42 ± 1 MHz N female / TNC male GPS 26
86010142 1575.42 MHz GPS TNC female 27
New product * All systems lying in the specified frequency bands can be operated, e.g. GSM-R, GSM, UMTS, LTE, …** Antennas will be phased out in 2018
Installation Guidelines can be found from page 28 onwards. Standards / guidelines for Train Antennas are listed on page 32 and 33.For further information, please contact [email protected]
SummaryAntennas for Trains and Buses87.5 ... 6000 MHz
4
Multi-band Combiners
Many train antennas provide multiple frequency bands within one antenna. All these frequency bands are fed into the antenna via one common antenna input.In order to combine the different frequency bands onto the common antenna input, multi-band combiners can be used. Depending on the number of combined frequency bands, e.g. dual-, triple- or quad-band combiners can be selected. Kathrein offers a variety of different frequency combinations for multi-band combiners. An according
up-to-date product overview can be found in the current catalogue for mobile communication products or on our homepage.
Examples of multi-band combiners:
Dual-band combiner
Triple-band combiner
Quad-band combiner
5
Multi-band Combiners
Port 3
Port 2
Port 1
For Example: Combiner (order separately)
Type No. 728954
Pass band Band 1 Band 2
MHzMHz
68 – 470870 – 970
Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3
dBdB
< 0.5 (68 – 470 MHz)< 0.5 (870 – 970 MHz)
Isolation Port 1 ↔ Port 2 dB > 45VSWR < 1.2Impedance Ω 50Input power Band 1 Band 2
WW
< 50< 50
Intermodulation products
dBc < –160(2nd/3rd order; with 2 x 20 W)
Temperature range °C –20 ... +70Connectors N femaleApplication IndoorDC transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Port 3 ↔ Port 2
By-pass (max. 2500mA)short circuited
stopWeight g | lb 800 | 1.8Packing size mm
inches285 x 55 x 12511.2 x 2.2 x 4.9
Dimensions (w x h x d)
mminches
229.4 x 32 x 111.6 (without connectors)9.0 x 1.3 x 4.4 (without connectors)
6
Train Antenna87.5 – 108 MHz727313n FM-broadcast receiving antenna for rail vehicles in fiberglass
radome.n Only for receiving.
Type No. 727313
Input N femaleFrequency range MHz 87.5 – 108Impedance Ω 50 ΩPolarization VerticalRadome weight g | lb 365 | 0.8Total weight g | lb 900 | 2.0Packing size (outside)
mminches
151 x 90 x 4155.9 x 3.5 x 16.3
Material: Flange: Aluminum.Radiator: Copper.Radome: Fiberglass; Colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and EPDM. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 100 x 200 cm | 39.4 x 78.7 inches by means of existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
7
Tram and Bus Antenna146 – 174 MHzK50222..n Broadband antenna in fiberglass radome.
Driving direction
Type No. K5022211601620
K5022212600055
Input N female UHF femaleFrequency range MHz 143 – 162
but preferred range: 146 – 156VSWR < 1.4Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Radome weight g | lb 470 | 1.0Total weight g | lb 1200 | 2.6Packing size mm
inches260 x 260 x 13010.2 x 10.2 x 5.1
Type No. K5022221600825
K5022222600057
Input N female UHF femaleFrequency range MHz 152 – 178
but preferred range : 156 – 174VSWR < 1.4Gain dB 0 dB (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Radome weight g | lb 470 | 1.0Total weight g | lb 1200 | 2.6Packing size mm
inches260 x 260 x 13010.2 x 10.2 x 5.1
Material: Radiator and Base: Aluminum.Radome: Fiberglass, colour: Grey.Studs and all screws and nuts: Stainless steel.Sealing: Neoprene and polyurethane. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface 1.0 x 2.0 m | 39.4 x 78.7 inches min. with 3 studs M10 and counterflange.Note: No superstructures in this area.
Grounding andhigh voltage protection:
DC grounded to protect against lightning and high-tension lines.
Scope of supply: Antenna with 3 studs, each with 2 nuts, 1 rubber gasket and 1 counterflange.
8
Train Antenna146 – 174 MHz733707n Aluminum antenna in fiberglass radome.
Type No. 733707
Input N femaleFrequency range MHz 146 – 174VSWR < 2.0Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50 °C ambient temperature)Radome weight g | lb 365 | 0.8Totel weight g | lb 800 | 1.8Packing size (outside)
mminches
151 x 90 x 4155.9 x 3.5 x 16.3
Material: Radiator and flange: Aluminum.Radome: Fiberglass, colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and EPDM. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface 200 x 100 cm | 78.7 x 39.4 inches min. with 4 studs M10.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
9
Train Antenna380 – 430 MHz and GPS 1575 MHz87010005n Two-band antenna: 380 – 430 MHz and GPS.n The antenna can be operated in both frequency ranges
simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
contact area
contact area
seal
Input Antenna400 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
Input AntennaGPS
1) 32 | 1.3
Mounting flange:
Type No. 87010005
Antenna multi-bandInput N femaleFrequency range MHz 380 – 430VSWR < 1.7Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range MHz 1575.42 ±1VSWR < 1.5Polarization Right hand circularGain (90° elevation) dB 2 (ref. to the circularly polarized
isotropic antenna)Impedance Ω 50Inner conductor DC groundedRadome weight g | lb 186 | 0.4Weight g | lb Approx. 500 | 1.1Packing size mm
inches150 x 90 x 1905.9 x 3.5 x 7.5
Height mminches
1505.9
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm | 39.4 x 39.4 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna 380 – 430 MHz appears. Depending on the level of the signal applied at the input of the antenna 380 – 430 MHz, the GPS receiver may be overloaded or damaged. Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
10
Train Antenna380 – 430 MHz87010008n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010008
AntennaInput N femaleFrequency range MHz 380 – 430VSWR < 1.7Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedRadome weight g | lb 186 | 0.4Total weight g | lb Approx. 500 | 1.1Packing size, L x W x H
mminches
150 x 90 x 1905.9 x 3.5 x 7.5
Height mminches
1505.9
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm | 39.4 x 39.4 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
contact area
contact area
seal
Input Antenna 400 MHz
82
5685
145 11
543
142
11 m
m d
iam
eter
32
Mounting flange:
Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
11
Tram and Bus Antenna406 ... 470 MHzK702321., K702323.
Frequency range 406 – 428 MHz
Type No. K7023210602284
Input M 11 x 1 female(the connector for cable RG 58 C/U is supplied).
Drill hole dimension
mminches
120.5
Frequency range MHz 406 – 428 MHzVSWR 406 – 410 MHz: < 1.9
410 – 425 MHz: < 1.7425 – 428 MHz: < 1.9
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 50 W (at 50 °C ambient temperature)Weight g | lb 400 | 0.9 lbPacking size (outside)
mminches
117 x 117 x 1144.6 x 4.6 x 4.5
Height mminches
702.8
Mounting On a conductive surface 70 x 70 cm | 27.6 x 27.6 inches min.
Frequency range 440 – 470 MHz
Type No. K7023230602285
K702323601363
K7023231602286
Input M 11 x 1 female(the connector for cable RG 58 C/U
is supplied).
M 11 x 1 female(the connector for cable RG 213/U is supplied).
N female
Drill hole dimension
mminches
120.5
120.5
170.7
Frequency range 440 – 470 MHzVSWR 440 – 450 MHz: < 1.7
450 – 465 MHz: < 1.5465 – 470 MHz: < 1.7
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50 Ω Polarization VerticalMax. power W 50 W (at 50 °C ambient temperature)Weight g | lb 400 | 0.9Packing size (outside)
mminches
117 x 117 x 1144.6 x 4.6 x 4.5
Height mminches
702.8
Mounting On a conductive surface 50 x 50 cm | 19.7 x 19.7 inches min.
Material: Radiator and base: Aluminum.Radome: High impact plastic.All screws and nuts: Stainless steel.
Mounting: The drilling diameter is 12 mm except the N connector versions: 17 mm. A special zinc washer ensures a good contact at the edges of the hole.
Special features: All metall parts of this antenna are DC grounded.Extreme robust and car-wash proof vehicular antenna.
12
Train Antenna410 – 470 MHzK702021n Low profile broadband antenna in fiberglass radome.
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
Type No. K702021
Input N femaleFrequency range MHz 410 – 470VSWR < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 170 (at 50° C ambient temperature)Radome weight g | lb 159 | 0.4Total weight g | lb 500 | 1.1Packing size (outside)
mminches
151 x 87 x 2105.9 x 3.4 x 8.3
Material: Radiator and Flange: Aluminum.Radome: Fiberglass, colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and rubber. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
13
Train Antenna410 – 430 / 450 – 470 MHz725892, K702121
Type No. 725892 K702121601119
Input N femaleFrequency range MHz 410 – 430 450 – 470VSWR < 1.5Gain dB 2 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 640 (at 50° C ambient temperature)Radome weight g | lb 365 | 0.8 lbWeight g | lb 800 | 1.8Packing size (out-side)
mminches
151 x 90 x 4155.9 x 3.5 x 163
Material: Radiator and Flange: Aluminum.Radome: Fiberglass, color: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and EPDM. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
n 2 dB gain broadband antenna in fiberglas radome.
14
Train Antenna380 – 400 MHz and 870 – 960 MHz741557n Two-band antenna in fiberglass radome working in the
380 – 400 MHz and 870 – 960 MHz range.n The antenna can be operated in both frequency ranges
simultaneously by using the combiner 728954.
Type No. 741557
Input N femaleFrequency range MHz 380 – 400 and 870 – 960VSWR < 1.5Gain dB 0 dB (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 500 W (at 50° C ambient temperature)Radome weight g | lb 159 | 0.4Total weight g | lb 500 | 1.1Packing size (outside)
mminches
151 x 87 x 2105.9 x 3.4 x 8.3
Material: Radiator: Brass.Flange: Aluminum.Radome: Fiberglass; Colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and rubber. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting hole for the connector:
33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint
for electrical contact.
Mounting flange:
13 |
0.5
115
| 4.5
43
| 1.7
145
| 5.7
80 | 3.6
32 |1.3
56 | 2.2
28 | 1.1
nich
t la
ckie
rtno
t p
aint
ed
Dic
htun
gsrin
gS
ealin
g O
-rin
g
nich
t la
ckie
rtno
t p
aint
ed
All dimensions in mm | inches
15
Train Antenna430 – 470 MHz and 870 – 960 MHz87010009n Two-band Antenna: 430 – 470 MHz / 870 – 960 MHzn Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010009
Antenna two-bandInput N femaleFrequency range MHz 430 – 470
870 – 960VSWR < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedRadome weight g | lb 186 | 0.4Total weight g | lb Approx. 500 | 1.1Packing size, L x W x H
mminches
150 x 90 x 1905.9 x 3.5 x 7.5
Height mminches
1505.9
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm | 39.4 x 39.4 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
contact area
contact area
seal
Input Antenna450 MHz /900 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
1) 32 | 1.3
Mounting flange:
Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
16
Type No. 87010006
Antenna multi-bandInput N femaleFrequency range MHz 430 – 470
870 – 960VSWR < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range MHz 1575.42 ±1VSWR < 1.5Polarization Right hand circularGain (90° elevation) dB 2 (ref. to the circularly polarized
isotropic antenna)Impedance Ω 50Inner conductor DC groundedRadome weight g | lb 186 | 0.4Weight g | lb Approx. 500 | 1.1Packing size mm
inches150 x 90 x 1905.9 x 3.5 x 7.5
Height mminches
1505.9
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm | 39.4 x 39.4 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna two-band appears. Depending on the level of the signal applied at the input of the antenna two-band, the GPS receiver may be overloaded or damaged.
Train Antenna430 – 470 MHz / 870 – 960 MHz and GPS 1575 MHz87010006n Multi-band antenna: 430 – 470 MHz / 870 – 960 MHz and GPS.n The antenna can be operated in all frequency ranges
simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
contact area
contact area
seal
Input Antenna450 MHz /900 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
Input AntennaGPS
1) 32 | 1.3
Mounting flange:
Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
17
Mounting hole for the connector:
33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint
for electrical contact.
Mounting flange:
Train Antenna450 – 470 MHz and 790 – 960 MHzK702061n Two-band antenna in fiberglass radome working in the
450 – 470 MHz and 790 – 960 MHz range.n The antenna can be operated in both frequency ranges
simultaneously by using the combiner 728954.
Type No. K702061602202
Input N femaleFrequency range MHz 450 – 470 and 790 – 960VSWR < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 500 (at 50° C ambient temperature)Radome weight g | lb 97 | 0.2Total weight g | lm 500 | 1.1Packing size (outside)
mminches
151 x 87 x 2105.9 x 3.4 x 8.3
Material: Radiator: Brass.Flange: Aluminum.Radome: Fiberglass; Colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of 4 existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
13 |
0.5
115
| 4.5
43
| 1.7
145
| 5.7
80 | 3.6
32 |1.3
56 | 2.2
28 | 1.1
nich
t la
ckie
rtno
t p
aint
ed
Dic
htun
gsrin
gS
ealin
g O
-rin
g
nich
t la
ckie
rtno
t p
aint
ed
All dimensions in mm | inches
18
Train Antenna870 – 960 MHz741009
Type No. 741009
Input N femaleFrequency range MHz 870 – 960 MHzVSWR < 1.5Gain dB 0 dB (ref. to quarter-wave antenna)Impedance Ω 50 ΩPolarization VerticalMax. power W 100 W (at 50 °C ambient temperature)Radome weight g | lb 166 | 0.4Total weight g | lb 500 | 1.1Packing size (outside)
mminches
137 x 92 x 1745.4 x 3.6 x 6.9
Material: Radiator: Brass.Flange: Aluminum.Radome: Fiberglass; Colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and nitrile rubber. Note: Don’t use detergents that might harm the sealing
Mounting: On a conductive surface of a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of 4 existing M10 studs.
Grounding and high voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting flange:
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
All dimensions in mm | inches.
145 | 5.7
82 |
3.2
115 | 4.5
43 | 1.7
28 |
1.1
∅ 13 | 0.5
56 |
2.2
32 | 1
.3
not painted sealing O-ring not painted
n Broadband antenna of very low profile in fiberglass radome.n Special radome suitable for high-speed trains.n The antenna fulfils the requirements according to EN 50155.
163 | 6.4
95 |
3.7
19
Train Antenna876 – 960 MHzK7021631n Broadband gain antenna in fiberglass radome.
Type No. K7021631602382
Input N femaleFrequency range MHz 876 – 960VSWR < 1.5Gain dB 3.5 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 500 (at 50 °C ambient temperature)Radome weight g | lb 365 gTotal weight g | lb 1000 gPacking size (outside)
mminches
151 x 90 x 4155.9 x 3.5 x 16.3
Material: Radiator: Brass.Flange: Aluminum.Radome: Fiberglass, colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and EPDM. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of 4 existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
20
Train Antenna790 – 2700 MHz87010007
Type No. 87010007
Antenna multi-bandInput N femaleFrequency range MHz 790 – 2700 MHzVSWR 790 – 806 MHz: < 2.2
806 – 870 MHz: < 2.0 870 – 2550 MHz: < 1.52550 – 2700 MHz: < 2.0
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedRadome weight g | lb 115 | 0.3Total weight g | lb Approx. 500 | 1.1Packing size, L x W x H
mminches
152 x 91 x 1256.0 x 3.6 x 4.9
Height mminches
813.2
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
contact area
contact area
seal
Input Antenna790 – 2700 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
1) 32 | 1.3
Mounting flange:
n Multi-band antenna: 800/900/1800/1900/UMTS/LTE/W-LAN.n The antenna can be operated in all frequency ranges
simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
21
Train Antenna694 – 2700 MHz and GPS 1575 MHz87010023n Multi-band antenna: 700/800/900/1800/1900/UMTS/2600/
LTE/W-LAN and GPS.n The antenna can be operated in all frequency ranges simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010023
Antenna multi-bandInput N femaleFrequency range MHz 694 – 2700VSWR 694 – 720 MHz: < 2.2
720 – 870 MHz: < 2.0870 – 925 MHz: < 1.6925 – 2700 MHz: < 2.0
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range MHz 1575.42 ±1VSWR < 1.5Polarization Right hand circularGain (90° elevation) dB 2 (ref. to the circularly polarized
isotropic antenna)Impedance Ω 50Inner conductor DC groundedRadome weight g | lb 115 | 0.25Total weight g | lb 540 | 1.1Packing size mm
inches152 x 91 x 1256.0 x 3.6 x 4.9
Height mminches
813.2
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna multi-band appears. Depending on the level of the signal applied at the input of the antenna multi-band, the GPS receiver may be overloaded or damaged.
contact area
contact area
seal
Input Antenna694 – 2700 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
Input AntennaGPS
1) 32 | 1.3
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
Situation of mounting
Mounting flange:
All dimensions in mm | inches
22
Train Antenna790 – 2700 MHz and GPS 1575 MHz87010003n Multi-band antenna: 800/900/1800/1900/UMTS/
LTE/W-LAN and GPS.n The antenna can be operated in all frequency ranges simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010003
Antenna multi-bandInput N femaleFrequency range MHz 790 – 2700VSWR 790 – 806 MHz: < 2.2
806 – 870 MHz: < 2.0 870 – 2550 MHz: < 1.52550 – 2700 MHz: < 2.0
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range MHz 1575.42 ±1VSWR < 1.5Polarization Right hand circularGain (90° elevation) dB 2 (ref. to the circularly polarized
isotropic antenna)Impedance Ω 50Inner conductor DC groundedRadome weight g | lb 115 | 0.3Total weight g | lb Approx. 500 | 1.1Packing size mm
inches152 x 91 x 1256.0 x 3.6 x 4.9
Height mminches
813.2
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna multi-band appears. Depending on the level of the signal applied at the input of the antenna multi-band, the GPS receiver may be overloaded or damaged.
contact area
contact area
seal
Input Antenna790 – 2700 MHz
82 | 3.2
56 | 2.285 | 3.3
145
| 5.7
115
| 4.5
43 |
1.7
142
| 5.6
11 |
0.4
dia
met
er
1)
Input AntennaGPS
1) 32 | 1.3
Situation of mounting
Mounting flange:
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
23
Train Antenna694 – 6000 MHz and GPS, GLONASS, BEIDOU87010012, 87010022n Multi-band antenna: 700/800/900/1800/1900/UMTS/2600/3500/5000/
LTE/W-LAN and GPS, GLONASS, BEIDOU.n The antenna can be operated in all frequency ranges simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010012 87010022
Antenna multi-bandInput N femaleFrequency range MHz 694 – 6000VSWR 694 – 960 MHz: < 1.5
1350 – 4920 MHz: < 1.84920 – 6000 MHz: < 2.0
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 40 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPS / Galileo / GLONASS / BEIDOUCenter frequency MHz 1581 ± 5Bandwidth in 10 dB MHz 49Polarization Right hand circularPeak gain at Fc dBic 3Integrated LNAFrequency range MHz 1550 – 1610VSWR < 2.0Impedance Ω 50Gain dB 23 ± 3Noise figure dB typ. 2.0, max. 2.5Operation voltage V 2.5 ... 5.5Operation current mA typ. 7, max. 10Input SMA female N female
110 mm | 4.3 inches cable lengthRadome weight g | lb 180 | 0.4Total weight g | lb 630 | 1.4Packing size mm
inches170 x 120 x 1006.7 x 4.7 x 3.9
Height mminches
933.7
Material: Radiator: AluminumFlange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Polyurethan and silicone. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
EU-RED: Hereby, KATHREIN-Werke KG declares that the radio equipment type 87010012 and 87010022 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.kathrein.com
43 |
1.7
115
| 4.5
146
| 5.7
11 |
0.4
dia
met
er
56 | 2.2
86 | 3.4
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
Situation of mounting
Mounting flange:
All dimensions in mm | inches
93 |
3.7
24
Type No. 87010032
Antenna multi-bandInput N femaleFrequency range MHz 694 – 6000VSWR 694 – 960 MHz: < 1.5
1350 – 4920 MHz: < 1.84920 – 6000 MHz: < 2.0
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 40 (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPS / Galileo / GLONASS / BEIDOUCenter frequency MHz 1581 ± 5Bandwidth in 10 dB MHz > 49VSWR at Fc < 2.0Polarization Right hand circularImpedance Ω 50Input TNC male,
110 mm | 4.3 inches cable lengthRadome weight g | lb 180 | 0.4Total weight g | lb ~ 610 | ~ 1.34Packing size mm
inches170 x 120 x 1006.7 x 4.7 x 3.9
Height mminches
933.7
Material: Radiator: AluminumFlange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Polyurethan and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Train Antenna694 – 6000 MHz and GPS, GLONASS, BEIDOU87010032n Multi-band antenna: 700/800/900/1800/1900/UMTS/2600/3500/5000/
LTE/W-LAN and GPS, GLONASS, BEIDOU.n The antenna can be operated in all frequency ranges simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
43 |
1.7
115
| 4.5
146
| 5.7
11 |
0.4
dia
met
er
56 | 2.2
86 | 3.4
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.
Note: Keep mounting surface clear of paint for electrical contact.
Evenness of opposite surface 0.2 mm | 0.008 inches.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nut M10 DIN 1587 torque 15 Nm – 20 Nm Added sealing
washer
5 1
Hex-head screw M10 torque 15 Nm – 20 Nm
15 |
0.6
Mounting flange:
93 |
3.7
25
Train Antenna1710 – 3800 MHz87010010n Multi-band antenna: 1800/1900/UMTS/LTE/W-LAN/WiMAX.n The antenna can be operated in all frequency ranges
simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010010
Antenna multi-bandInput N femaleFrequency range MHz 1710 – 3800VSWR 1710 – 1920 MHz: < 1.6
1920 – 3800 MHz: < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedRadome weight g | lb 115 | 0.3Total weight g | lb 450 | 1.0Packing size, L x W x H
mminches
152 x 91 x 1256.0 x 3.6 x 4.9
Height mminches
813.2
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
contact area
contact area
seal
82
56 85
145 11
5 43
142
11 m
m d
iam
eter
32
Input AntennaMulti-band
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electri-cal contact.
Evenness of opposite surface 0.2 mm.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nutM10 DIN 1587torque15 Nm – 20 NmAdded sealing
washer
51
Hex-head screw M10torque15 Nm – 20 Nm
Mounting flange:
26
Train Antenna1710 – 3800 MHz and GPS 1575 MHz87010011n Multi-band antenna: 1800/1900/UMTS/LTE/W-LAN/WiMAX and GPS.n The antenna can be operated in all frequency ranges simultaneously.n Low profile antenna in fiberglass radome.n The antenna fulfils the requirements according to EN 50155.
Type No. 87010011
Antenna multi-bandInput N femaleFrequency range MHz 1710 – 3800VSWR 1710 – 1920 MHz: < 1.6
1920 – 3800 MHz: < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50 ΩPolarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC grounded
Antenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range MHz 1575.42 ±1VSWR < 1.5Polarization Right hand circularGain (90° elevation) dB 2 (ref. to the circularly polarized
isotropic antenna)Impedance Ω 50Inner conductor DC groundedRadome weight g | lb 115 | 0.3Total weight g | lb Approx. 500 | 1.1Packing size mm
inches152 x 91 x 1256.0 x 3.6 x 4.9
Height mminches
813.2
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna multi-band appears. Depending on the level of the signal applied at the input of the antenna multi-band, the GPS receiver may be overloaded or damaged.
contact area
contact area
seal
82
56 85
145 11
5 43
142
11 m
m d
iam
eter
32
Input Antenna GPS
Input AntennaMulti-band
Mounting hole for the connector: 33 (max. 35) mm diameter.
Note: Keep mounting surface clear of paint for electri-cal contact.
Evenness of opposite surface 0.2 mm.
Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nutM10 DIN 1587torque15 Nm – 20 NmAdded sealing
washer
51
Hex-head screw M10torque15 Nm – 20 Nm
Situation of mounting
Mounting flange:
27
Low Noise Amplifier GPS86010142
n The low noise amplifier 86010142 is designed for the use inside vehicles with train antennas with GPS.
n It includes a preselection filter to prevent the inter ference in case of simultaneous operation at the frequency range 380 – 960 / 1710 – 3800 MHz and GPS.
n The product fulfils the requirements according to EN 50155.
Block Diagram
InputTNC female
OutputN female
bias-Tbandpassfilter GPS
bandpassfilter GPS
bandpassfilter GPSamplifier amplifierlowpass
Type No. 86010142
Frequency MHz 1575.42, L1-signalGain dB 25 ±2Noise figure dB < 2.0VSWR (input, output) < 1.8Operation voltage 3.3 ... 5.5 V, ripple < 50 mV,
supplied at inner conductor RF-outputOperation current mA ≤ 25Connector input TNC femaleConnector output N femaleDimensions (w x h x l)
mminches
70 x 22 x 502.8 x 0.9 x 2.0
Mounting mminches
4 holes, 4.5 diameter4 holes, 0.2 diameter
Additional features:n The maximum input power at the input of the amplifier at
the frequency range 380 – 960 MHz and 1710 – 3800 MHz is limited to +25 dBm.
n The noise level at the GPS-frequency generated by the operation at the frequency range 380 – 960 MHz and 1710 – 3800 MHz should not exceed the thermal noise level at the input of the GPS-amplifier, otherwise the noise figure will be increased.
Environmental conditions:n Temperature range: –25 °C … +55 °C (data as specified)
–40 °C … +85 °C (extended range) *)n Protection class: IP 54 (DIN 40050 / IEC 144)
(hanging installation position)
*) Extended range of operation: Within an extended temperature range of –40 °C … +85 °C and an extended supplied voltage range of 3.0 V … 6.0 V operation is possible with the following restrictions: Noise figure: < 2.5 dB Gain: > 20 dB
53 | 2.1
70 | 2.8
22 |
0.9
1)
2)50
| 2.
0
3)
30 |
1.2
Input (Antenna)
TNC
93 |
3.7
Output(DC +3.3 ... 5.5 V)
N
Hanging installation position
bottom
top
ceiling
1) 5 | 0.22) 4.4 | 0.173) 7 | 0.28
All dimensions in mm | inches
28
Installation Guidelines
Train antennas made by Kathrein are well known as
reliable and highly sophisticated products.
Our antennas are distinguished by excellent
voltage protection against accidentally high voltage
contacts due to well developed grounding elements
implemented in the overall design.
Depending on frequency and design constraints,
Kathrein antennas are designed as λ/4 radiators or as
λ/2 radiators. For proper functionality, λ/4 radiators
have to be mounted on a conductive surface creating
a ground plane. Train antennas are usually vertically
polarized. The impedance is 50 Ohm.
Kathrein antenna designs are tested in accordance
with the standards indicated on page 26 and 27.
Train antennas are subject to extreme environ-
mental conditions and have to withstand tremendous
operational conditions. The following documents will
help to understand functionality and give information
about proper installation procedures.
A key feature of Kathrein antennas to pass these
requirements is the ability to limit the connector
voltage to 60 V in case of contact with high tension
lines. A current flow of 40 kA over a time frame of
100 ms and high voltages of up to 42 kV could be
applied under worst case conditions.
Quality is the Key
Abstract
Design
Low Noise Amplifier(GPS)
Train Antennas
29
Installation Guidelines
Fundamental RF basics require metallic surfaces for
certain antenna designs. Utilizing λ/4 technologies
depends on a sufficient ground plane surface to
finally distribute RF wave into the surroundings. There-
fore, these particular antennas need to be mounted
against a conductive surface to create the required
ground plane.
Metallic Surfaces
In most of the cases, the roofs of trains are made out
of metallic materials. These materials have a reasonable
conductivity to achieve best radiation results. For
safety reasons, these surfaces need to offer sufficient
grounding to finally lead high voltages and currents to
ground.
Non-Metallic Surfaces
Train designs appear more and more with non- metallic
surfaces mostly present at the front or the end of a
train. Apparently those areas are preferred installation
areas for antennas.
As explained previously, antennas require ground
planes made out of conductive material. Several
Each data sheet gives detailed information about
the surface size. We strongly recommend not to stay
under the minimum mounting requirements. Antennas
easily will lose VSWR performance, and their radiation
pattern may change dramatically.
designs may apply to create such a plane. Metallic
foils might be placed underneath a non-metallic
train body. Other metals might be laminated into
fiberglass constructions. The antenna flange needs
to have good electrical contact to these additional
ground planes.
The same mandatory rule applies as with metallic
surfaces: A sufficient grounding of the antenna needs
to be considered in the design. Any kind of grounding
needs to handle high currents and voltages, and finally
lead them to ground.
Ground Plane
Figure 1: Electrical field and radiation pattern of a λ/4 antenna design
Installation
E - Fieldλ/4
electricalground plane
virtualfield lines
3 dB
10
0
Horizon
30
Installation Guidelines
In case of an accident or a failure of the high tension
line (overhead contact line), high voltage and current
might be applied to the antenna. To protect people and
equipment, the connector voltage of the antenna is not
to exceed 60 V. To guarantee low connector voltages,
antenna flanges need to be grounded thoroughly.
n Unpainted areas near the four mounting holes of
the antenna flange.
To achieve best conductivity, mounting surfaces at
the antenna socket and the mating surface of the
train should be clean. Any paint residues or other types
of pollution need to be removed prior to the mounting
process.
• In case of non-metallic roof surfaces with an
additional ground plane of e. g. thin material, a
Most antennas are designed with a standardized foot
print of the mounting socket. Dimensions are stated in
the data sheets.
Mounting Sockets
Most antenna sockets offer four screw holes to tighten
the flange against the mounting surface.
We recommend the following:n Mounting against a separate flange with integrated
mounting bolts. This flange is usually welded to the
train.
In general, mounting screws or nuts should not add
more than 15 mm to the mounting surface, especially
if cap nuts are used.
In case of an antenna installation with screws through
the antenna socket into the vehicle, particular
attention should be paid to the sealing of the
screws under consideration of the grounding
instructions.
separate ground ing of the antenna mounting flange
is required.
Mounting Position
The antennas have to be mounted directly to the
ground plane.
Depending on the overall mounting situation (please
refer to “Obstacles close to the antenna”) it is tempting
to elevate antennas against the train roofs with high
flanges or other objects. To avoid mistuning and
malfunctioning antennas, it is mandatory not to mount
any such objects between the antenna and the roof.
Resonance frequency, radiation pattern, and VSWR
would change dramatically or could be lost completely.
Grounding
Mounting
Figure 3: Low profile broad band antenna with mounting screws
Figure 2: Inside grounding
grounding rod
31
Installation Guidelines
To avoid corrosion and leakage into the vehicle,
antenna connectors must be sealed against the
mounting plate. Every Kathrein antenna is supplied
with detailed mounting instructions. An O-ring is
supplied with each antenna to seal the through hole
in the vehicle body against the antenna connector. For
certain types, this ring runs around the whole flange. To
For optical reasons, the color of train antennas some-
times has to match certain other colors. Kathrein
antennas are particularly suitable for subsequent,
long-lasting painting since the visible parts (radomes)
are generally made of fiberglass (polyester), to which
paint adheres very well. A thin layer of paint eventually
has only a negligible influence on the electrical
characteristics.
General remarks:n We recommend that painting is only performed
by qualified professional painting companies. If
required, painting on site may also be possible (and
permissible).
For proper wave propagation from the antenna into the
surrounding area, the roof should be flat without any
obstacles.
Trains sometimes have a number of structures for
multiple purposes on their roofs. Any obstacles close
to the antenna may impact radiation pattern and
The distance to other antennas depends on the required
antenna isolation. This value has to be clarified with
the suppliers of the installed mobile communication
system.
An isolation of 30 dB is a preferred value.
Generally speaking, a distance of approximately
achieve advanced sealing, mating surfaces between
the antenna socket and mounting flange/mounting
surfaces have to be flat.
Sealing also needs to be performed around mounting
holes if no mounting flanges are used. Corrosion at
mating surfaces between the antenna and the mounting
plane is critical for proper functioning of the antenna.
n We recommend that painting is only applied to visible
surfaces: e.g.
– Fiberglass radome
– Antenna socket, upper surface – please refer to
instructions stated in our data sheets
n The contact area on the lower part of the flange must
be kept free of paint at all times.
n Suitable commercial paints consist of one or two
components. The manufacturer‘s instruction for
use and processing must be observed. Paints with
metallic effects or metallic components are not
permissible.
radiated waves. It is difficult to give general guidelines
about minimum distances. As a rule of thumb,
antennas should face no obstacles within a radius of
approximately 1 m or more.
5–7 lambda is required for antennas operating the
same frequency band.
Due to the selectivity of different systems, antennas
operating in different frequency bands require
distances that can be even smaller.
Sealing
Painting
Distances to Other Antennas
Obstacles Close to the Antenna
32
Overview of Standards / Guidelines for Train Antennas
7273
13
8701
0005
7337
07
8701
0008
K70
2021
7258
92
K70
2121
7415
57
8701
0009
UL94 HB • • • • • • • • •
DIN EN 45545-2: 2013 • • • • – • • • •
DIN 5510 T2 – • – • • – – • •
IP Class (when mounted properly) IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66
EN 50122-1 • • • • • • • • •
EN 50124-1 – • – • – – – - •
EN 50125 • • • • • • • • •
EN 50155 (environmental conditions) • • • • • • • • •
EN 60068-2-1 • • • • • • • • •
EN 60068-2-2 • • • • • • • • •
EN 60068-2-6 • • • • • • • • •
EN 60068-2-27 • • • • • • • • •
EN 60068-2-30 • • • • • • • • •
EN 61373 • • • • • • • • •
ETS 300 019-1-2 class 2.2 • • • • • • • • •
ETS 300 019-1-1 T 1.2 • • • • • • • • •
ETS 300 019-1-5 T 5.2 • • • • • • • • •
ETS 300 019-2-2 T 2.2 • • • • • • • • •
ETS 300 019-1-2 T 1.2 • • • • • • • • •
• Product complies with the standard/guidelines– Product does not meet the standard/guidelines
33
Overview of Standards / Guidelines for Train Antennas
8701
0006
K70
2061
7410
09
K70
2163
1
8701
0007
8701
0023
8701
0003
8701
0012
8701
0022
8701
0032
8701
0010
8701
0011
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • – • • • • • • • •
IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66 IP 66
• • • • • • • • • • • •
• – – – • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• Product complies with the standard/guidelines– Product does not meet the standard/guidelines
KATHREIN-Werke KGAnton-Kathrein-Straße 1 – 383022 Rosenheim, GermanyPhone +49 8031 184-0www.kathrein.com | [email protected]
9980
0000
58/0
/0118
/PSA
/onli
ne |
Tech
nical
data
subje
ct to
chan
ge.
Title
: foto
lia.co
m |
Luck
yImag
es