This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
I.C. ENGINE POWERED FORKLIFT TRUCK
Counter-Balance Type1,5 - 3,5 ton
Havelange Forklifts,Havelange Forklifts,
driven by servicedriven by service www.havelangeforklifts.be
SUBSTANTIALLY REDUCED VIBRATION BY ADOPTING DUAL-FLOATING SYSTEMS FOR BOTH THE ENGINE AND HOOD
Minimizes the transfer of vibration to the operator, with four-point rubber cushion absorbers between the seat and engine and its transmission. Moreover, use of the same four-point suspension adopted in the hood, realizing a dual effect in reducing vehicle vibrations.
GENERAL
EXPANSIVE FLOOR SPACE FOR EASIER FOOT MANEUVERING
An amazing 45% increase in fl oor space by placing tilt cylinders under the fl oor. This gives a smooth footwell in addition to easy entry and exit.
MORE CONVENIENT PARKING LEVER
The lever is positioned to the right of the steering wheel for easier entry and exit. A double-action brake release on the lever further improves safety.
EXTRA ENTRY AND EXIT FROM AN EXTRA-WIDE STEP -- 55% WIDER
The secure step with enlarged foot space enables greater comfort and less fatigue while entering and exiting the vehicle.
MULTIFUNCTIONAL SUSPENSION SEAT (available for 1.5/1.8 ton high power & 2/3.5 ton models)
Features include reinforced driver support, reduced vibration, operator weight balance adjusting, forward and backward reclining, a rear utility pocket and seat belt.
RESIN SCREENThe resin screen on the overhead guard enables comfortable outdoor operation in wet weather.
SUPERIOR MANEUVERABILITY AND ASSURED SAFETY
INNOVATIVE FORK-LANDING MECHANISM (available for wide view two-stage mast)
The fork-lowering speed decelerates at a height of approximately 150 mm above the ground enabling accurate placement of the forks into the load fork pockets or pallet.
REDUCED FATIGUE DUE TO A SEMI-CIRCULAR STEERING WHEELA smaller diameter (300 mm outer diameter) steering wheel gives improved vehicle maneuverability. In addition, this compact steering wheel makes it much easier to get on and off the truck.
METER PANEL OPTIMALLY LOCATED TO THE RIGHT OF THE DRIVER’S SEAT
The meter panel is located on the top right side of the dashboard for easier readability by the operator.
MULTI-CONE SYNCHRONIZER SHIFT LEVERSThe newly adopted levers enable smooth shifting from both forward and reverse (available for manual transmission models).
ANTI-ROLL MECHANISM FOR ASSURED SAFETY DURING TURNING (available for 2-3.5 ton models)Warning: This system does not guarantee accident avoidance or prevention of vehicle overturning.
NEUTRAL SAFETY MECHANISMThis feature enhances safety of operation. The engine cannot be started unless the change lever is in the neutral position.
HIGH-MOUNT REAR COMBINATION LIGHTS
The rear combination lights are installed on the top left and right sides of the overhead guard for easier recognition by on-site workers.
ANTI-SLIP MAT ON THE HOOD
A rubber strip is attached to the hood to prevent slippage while stepping on and off.
METER PANEL WITH LCD INDICATORS
The LCD has a longer life and is easy to read even during daylight shift operation.
Clearer visibility of the fork tips -- 50% improvement over other current models. This achievement was made possible by lowering the dashboard by 70mm and the tie bar by 190mm. A remarkable improvement of the forward view along with quicker recognition of the fork position. An operator-friendly design with assured safety, high effi ciency and relaxing feel.
• Amazing backward visibilityReshaped counter weight for better rearview sight. The round shape of the rear top end of the
counterweight substantially improves visibility for increased safety during backward movement.
RUGGEDNESS AND INCREASED DURABILITY
5% IMPROVED FRONT AND REAR STABILITY RATIO (available for 2-3.5 ton models)
Stable and more consistent cargo handling as well as travel due to an improved stability ratio.
STURDIER MASTMinimized distortion of the mast by redesigned positioning the mast supports and tilt cylinders. TCM’s traditional robust mast was further upgraded by adopting sturdier tie bars, while maintaining a wide range of viewing angles.
IMPROVED DURABILITY WITH LUBRICANT FILLED LIFT CYLINDER
Oil fi lled lift cylinders give improved durability. (available for 2-3.5 ton models)
SINGLE-PIECE HEADGUARDThe front and rear pillars as well as roof are all welded together in a single-piece construction to give additional strenght to the entire structure.
COOLER RUNNING THROUGH IMPROVED AIRFLOW
Optimal positioning of the fan, radiator and muffl er has reduced the operating coolant temperature (gasoline models). The operating temperature of the hydraulic oil has been reduced, also by 10°C by upgrading the mechanical components and circuitry.
TCM TRANSMISSIONSTCM designed and developped these transmissions for quiet operation and maximum durability, and TCM builds them to insure the highest quality.
TCM STEERING AXLESAlso a new TCM design, the steer axle has been strengthened and improved for durability in demanding applications.
EASY MAINTENANCE AND ENVIRONMENT FRIENDLINESSDETACHABLE SIDE COVERS FOR CONVENIENT INSPECTION AND SIMPLE MAINTENANCE
Inspection and maintenance can more easily be performed due to one-touch detachable side covers and a wide-opening hood.
INTEGRAL LAYOUT OF ELECTRICAL PARTS AND OTHER SYSTEM DEVICES
Maintenance inspections can be performed more easily, as electrical parts such as the fuse box, relay and battery are neatly integrated into a conveniently compact area.
NEW ENGINES, COMPLIANT WITH WORLDWIDE 2nd STAGE EMISSION REGULATIONS
Powerful, yet appropriate, diesel engines, compliant with stringent global emissions regulations.
ONE-PIECE FLOORBOARD
Gives more convenient inspection and easier maintenance, as the one-piece fl oorboard unit is easily detachable without using any tools.
NEW OPTIONAL EQUIPMENT• Three-stage mast with four-
cylinder mechanism (available for 2-3 ton models)The cylinders are symmetrically located to the left and right for improved forward visibility.
• Integral Side ShifterA major improvement in the integral side shifter ensures less load loss and improved forward visibility.
• Low-noise mast (available for 2-3 ton models)Reduced noise from the fork and carriage signifi cantly reduces chain shudder.
• Lift LockWith the engine is off, the forks cannot be lowered, even when the operator is in the seat.
• Interlock SystemThis safety device allows traveling and loading/unloading only when the operator is in the seat.
PORTABLE GLOVE BOXDetachable and portable.
CUP HOLDERConvenient for keeping cups, pens and other small items.
OTHER OPTIONAL EQUIPMENT
Rotating warning light Rear working light Overhead exhaust system
Windshield wiper Cabin-panel type (available for 2-3.5 ton models)
Heater
LPG exclusive/Dual fuel(LPG/gasoline) package
Pre-cleaner engine air intake Steel cabin-enclosed type with air-cooler(available for 2-3.5 ton models)
Head light guard Air Boss tire
* As far as the detailed optional information is concerned, please refer to the specifi cation sheets.For various types of attachments, please also refer to the “attachment catalogue” which is separately prepared from this sales catalogue.
TCM has been engaged in manufacturing various forklift truck models that take into account the needs and requirements of our valued cutomers. Now, TCM proudly presents the ‘iNOMA series’ with such benefi ts as enhanced operator comfort, superior safety assurance, ruggedness and increased durability as well as easy maintenance and envirnment friendliness. These notable benefi ts are backed by TCM’s many years of experience and superb technological innovations, and TCM is confi dent in placing the full ‘iNOMA series’ product line on variaus job sites in markets around the world.
Mast
Model
Rated Capacity 500mm: load center (kg) Max. Fork
Height
Overall Mast Height Tilting AngleF / B
(1) Service Weight (kg)
FG / D15T13FG / D15C13
FG / D18T13FG / D18C13
Lowered Raised with Backrest
FG15T3FG15C3
FG18T3FG18C3
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD
NOTE: (1) For height without backrest: -505mm. (2) For free lift without backrest: +500mm.
Weight without backrest: -20kg. (3) Weight for diesel model: +30kg
NOTE: (1) For height without backrest: -505mm. (2) For free lift without backrest: +500mm.
Weight without backrest: -20kg. (3) Weight for diesel model: +110kg (TD27)
Wide view Full Free 3-stage Mast VFHM
NOTE: Rated Capacity with (*): Shows capacity with front dual tires. Service Weight of VM/VFM 550 - 600 and of VFHM 650 - 700 represents the weight of vehicles equipped with “special dual tires”. Lifting Speed with VFM/VFHM Mast: For FG/FD15T13 - FG/FD15C13 - FG/FD18T3 - FG/FD18C3 - FG15T3/C3 - FG18T3/C with VFM FG 470mm/s with load. 550mm/s without load. FD 420mm/s with load. 490mm/s without load. with VFHM FG 530mm/s with load. 610mm/s without load. FD 480mm/s with load. 540mm/s without load. For FHG15T3/C - FHD15T3Z/C3Z - FHG18T3/C3 - FHD18T3Z/C3Z - FHG15T3/C3 - FHG18T3/C with VFM FG 480mm/s with load. 560mm/s without load. FD 420mm/s with load. 540mm/s without load. with VFHM FG 540mm/s with load. 620mm/s without load. FD 560mm/s with load. 600mm/s without load. Lowering speed with VFM/VFHM mast: 420mm/s with load. 370mm/s without load. Overall Vehicle lenght with VFM mast: +10mm longer than of STD model with VM mast with VFHM mast: +25mm longer than of STD model with VM mast
Mast
Model
Rated Capacity 500mm: load center (kg) Max. Fork
Height
Overall Mast Height Tilting AngleF / B
(3) Service Weight (kg)
FG / FD 20 FG / FD 25 Lowered(1)Raised with
BackrestFG / FD 20 FG / FD 25
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm deg S DD SDD S DD SDD
NOTE: (1) For height without backrest: -455mm. (2) For free lift without backrest: +455mm.
Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240)
Wide view Full Free 3-stage Mast VFHM
MastModel
Rated Capacity 500mm: load center (kg)
FG / D20 FG / D25
Max. Fork
Height
Overall Mast Height
Lowered(1) Raised
with Backrest
Tilting AngleF/B
FG20 FG25
(3) Service Weight (kg)(2) Free Lift with
Backrest
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Serves Weight of VM/VFM 550 - 600 and of VFHM 650 - 700 represents the weight of vehicles equipped with “SDD: special dual tires”. Loading Speed with VFM/VFHM Mast: with VFM FG 480mm/s with load. 520mm/s without load. FD 540mm/s with load. 590mm/s without load. with VFHM FG 500mm/s with load. 540mm/s without load. FD 560mm/s with load. 610mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than that of STD model with VM/FM mast
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD
NOTE: (1) For height without backrest: -455mm. (2) For free lift without backrest: +455mm.
Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240)
Wide view Full Free 3-stage Mast VFHW (4 CYLINDER)
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM Mast: with VFM FG 450mm/s with load. 490mm/s without load. FD 520mm/s with load. 570mm/s without load. with VFHM FG 460mm/s with load. 510mm/s without load. FD 540mm/s with load. 590mm/s without load. Lowering speed with VFM/VFHM mast: 420mm/s with load. 380mm/s without load. Overall Vehicle lenght with VFW/VFHW (4CYLINDER) mast: +35mm longer than that of STD model with VM mast
MastModel
Rated Capacity 500mm: load center (kg)
FG / D20 FG / D25
Max. Fork
Height
Overall Mast Height
Lowered(1) Raised
with Backrest
Tilting AngleF/B
FG20 FG25
(3) Service Weight (kg)(2) Free Lift with
Backrest
NOTE: (1) For height without backrest: -455mm. (2) For free lift without backrest: +455mm.
Weight without backrest: -20kg. (3) Weight for diesel model: +130kg (TD27) +110kg(C240)
Wide view Full Free 2-stage Mast VFW (4 CYLINDER)
MastModel
Rated Capacity 500mm: load center (kg)
FG / D20 FG / D25
Max. Fork
Height
Overall Mast Height
Lowered(1) Raised
with Backrest
Tilting AngleF/B
FG20 FG25
(3) Service Weight (kg)(2) Free Lift with
Backrest
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD
NOTE: (1) For height without backrest: -580mm. (2) For free lift without backrest: +580mm.
Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240)
Wide view Full Free 3-stage Mast VFHM
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Serves Weight of VM/VFM 550 - 600 and of VFHM 650 - 700 represents the weight of vehicles equipped with “SDD: special dual tires”. Lifting Speed with VFM/VFHM Mast: with VFM FG 420mm/s with load. 440mm/s without load. FD 460mm/s with load. 530mm/s without load. with VFHM FG 430mm/s with load. 450mm/s without load. FD 480mm/s with load. 550mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than that of STD model with VM/FM mast
NOTE: (1) For height without backrest: -580mm. (2) For free lift without backrest: +580mm.
Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240)
NOTE: (1) For height without backrest: -580mm. (2) For free lift without backrest: +580mm.
Weight without backrest: -30kg. (3) Weight for diesel model: +140kg (TD27) +120kg(C240)
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM Mast: with VFM FG 360mm/s with load. 420mm/s without load. FD 430mm/s with load. 500mm/s without load. with VFHM FG 380mm/s with load. 430mm/s without load. FD 450mm/s with load. 520mm/s without load. Lowering speed with VFM/VFHM mast: 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFHM mast: +35mm/+45mm longer than that of STD model with VM mast
NOTE: (1) Figures for (2t, 2.5t model); For (3t model) +45mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -180mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg.
Wide view Full Free 3-stage Mast VFHM
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Service weight of VM/VFM 550 - 600 and of VFHM 650 - 700 represents the weight of vehicles equipped with “SDD: special dual tires”.
Lifting Speed with VFM/VFHM Mast: with VFM FG (2t, 2.5t model) 530mm/s with load. 560mm/s without load. FD (2t, 2.5t model) 550mm/s with load. 580mm/s without load. FG (3t model) 450mm/s with load. 470mm/s without load. FD (3t model) 470mm/s with load. 490mm/s without load. with VFHM FG (2t, 2.5t model) 560mm/s with load. 580mm/s without load. FD (2t, 2.5t model) 570mm/s with load. 600mm/s without load. FG (3t model) 460mm/s with load. 480mm/s without load. FD (3t model) 480mm/s with load. 500mm/s without load. Lowering speed with VFM/VFHM mast: (2t, 2.5t model) 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFM mast: +15mm longer than of STD model with VM mast
MastModel
Rated Capacity 500mm: load center (kg)
FHG / D20T3FHG / D20C3
Max. Fork
Height
Overall Mast Height
(1)Lowered
(2) Raised with
Backrest
Tilting AngleF/B
(4) Service Weight (kg)
FHG / D25T3FHG / D25C3
FHG / D30T3FHG / D30C3
(3) Free lift
with Backrest
FHG 20T3FHG 20C3
FHG 25T3FHG 25C3
FHG 30T3FHG 30C3
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM Mast: with VFM FG (2t, 2.5t model) 450mm/s with load. 490mm/s without load. FD (2t, 2.5t model) 510mm/s with load. 540mm/s without load. FG (3t model) 410mm/s with load. 470mm/s without load. FD (3t model) 430mm/s with load. 460mm/s without load. with VFHM FG (2t, 2.5t model) 460mm/s with load. 510mm/s without load. FD (2t, 2.5t model) 530mm/s with load. 560mm/s without load. FG (3t model) 430mm/s with load. 460mm/s without load. FD (3t model) 450mm/s with load. 480mm/s without load. Lowering speed with VFM/VFHM mast: (2t, 2.5t, 3t model) 400mm/s with load. 350mm/s without load. Overall Vehicle lenght with VFW/VFHW (4cylinder) mast (2t, 2,5t model): +35mm longer than of STD model with VM mast (3t model): +35mm/+45mm longer than of STD model with VM mast
NOTE: (1) Figures for (2t, 2.5t model); For (3t model) +80mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -145mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg.
Wide view Full Free 2-stage Mast VFW (4CYLINDER)
Wide view Full Free 3-stage Mast VFHW (4CYLINDER)
NOTE: (1) Figures for (2t, 2.5t model); For (3t model) +80mm (2) Figures for (2t, 2.5t model); For (3t model) +230mm. For height without backrest: (2t, 2.5t model) -455mm, (3t model) -580 mm (3) Figures for (2t, 2.5t model); For (3t model) -145mm. For free lift without backrest: (2t, 2.5t model) +455mm, (3t model) +580 mm. Weight for without backrest: (2t, 2.5t model) -20kg, (3t model) -30 kg (4) Weight for diesel model: (2t model) +120kg, (2.5t model) +120kg, (3t model) +130 kg.
MastModel
Rated Capacity 500mm: load center (kg)
FHG / D20T3FHG / D20C3
Max. Fork
Height
Overall Mast Height
(1)Lowered
(2) Raised with
Backrest
Tilting AngleF/B
(4) Service Weight (kg)
FHG / D25T3FHG / D25C3
FHG / D30T3FHG / D30C3
(3) Free lift
with Backrest
FHG 20T3FHG 20C3
FHG 25T3FHG 25C3
FHG 30T3FHG 30C3
MastModel
Rated Capacity 500mm: load center (kg)
FHG / D20T3FHG / D20C3
Max. Fork
Height
Overall Mast Height
(1)Lowered
(2) Raised with
Backrest
Tilting AngleF/B
(4) Service Weight (kg)
FHG / D25T3FHG / D25C3
FHG / D30T3FHG / D30C3
(3) Free lift
with Backrest
FHG 20T3FHG 20C3
FHG 25T3FHG 25C3
FHG 30T3FHG 30C3
PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) PNEUMATIC UNIQUE(SE) mm mm mm mm deg S DD SDD S DD SDD S DD SDD
NOTE: (1) For height without backrest: -530mm (2) For free lift without backrest: +530mm Weight for diesel model: -30kg
NOTE: Rated Capacity with (*): Shows capacity with DD: front dual tires. Lifting Speed with VFM/VFHM Mast: with VFM 530mm/s with load. 560mm/s without load. with VFHM 560mm/s with load. 580mm/s without load. Lowering speed with VFM/VFHM mast: 440mm/s with load. 380mm/s without load. Overall Vehicle lenght with VFHM mast: +15mm longer than of STD model with VM/VFM mast
STANDARD DIMENSIONS (Front Single Tire)
ModelFD/FG15 • FHD/FHG15 FD/FG18 • FHD/FHG18
mm mmOverall height, Fork raised (with backrest) 4030 4030
I Manufacturer TCM 2 Model FG15C13 FG15T13 FG18C13 FG18T13 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Gasoline 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum Fork Height mm 3000 10 Free Lift mm 155 13 Fork Size L x W x T mm 920 x 100 x 35 Fork Spread (Outside) Max. / Min. mm 920 / 200 14 Tilt Angle Fwd / Bwd deg 6 - 12 15 Length to Fork Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Mast Height Fork Lowered mm 1995 18 Mast Height Fork Raised mm 4030 19 Overhead Guard Height (EXB, EXK) mm 2070 Overhead Guard Height (EXC, EXE, EXN) mm 2130 20 Operator’s Seat Height mm 1015 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks)
Rear Overhang mm 425 455 23 Basic Right Angle Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Max. Full load km/h 14.0 / 14.0 (Fwd/Rvs.) No load km/h 14.5 / 14.5 25 Lifting Full load mm/s 590 No load mm/s 670 26 Lowering Full load mm/s 450 No load mm/s 550 28 Max. Drawbar Pull Full load kN 9.3 14.5 9.3 14.5 No load kN 6.9 30 Max. Gradeability* Full load % 24 29 20 24 No load % 18 32 Total Weight kg 2510 2670 33 Weight Distribution Full load Front kg 3510 3880 Rear kg 500 540 34 No load Front kg 1070 1030 Rear kg 1440 1640 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50 - 10 10PR 37 Rear 5.00 - 8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 Backrest Height mm 1045 Overhead Guard Clearance mm 1035 Counterweight Height mm 1110 Drawbar Pin Center Height mm 495 Step Height / Floor Height mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 28 49 Internal Combustion Engine Make/Model NISSAN K15 Rated Horsepower / r.p.m. kW 25.0 / 2250 Rated Torque / r.p.m. N•m 110.2 / 1600 51 Number of Cylinder 4 52 Piston Displacement cc 1486 Alternator output kW/Amp 0.60 / 50 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1 57 Operating Pressure For Attachments MPa (psi) 17.7
Cha
ract
eris
tics
Dim
ensi
ons
Perf
orm
ance
Wei
ght
Cha
ssis
Eng
ine
and
Tra
nsm
issi
on
*Computed values
I Manufacturer TCM 2 Model FHG15C3 FHG15T3 FHG18C3 FHG18T3 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Gasoline 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum Fork Height mm 3000 10 Free Lift mm 155 13 Fork Size L x W x T mm 920 x 100 x 35 Fork Spread (Outside) Max. / Min. mm 920 / 200 14 Tilt Angle Fwd / Bwd deg 6 - 12 15 Length to Fork Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Mast Height Fork Lowered mm 1995 18 Mast Height Fork Raised mm 4030 19 Overhead Guard Height (EXB, EXK) mm 2070 Overhead Guard Height (EXC, EXE, EXN) mm 2130 20 Operator’s Seat Height mm 1045 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks)
Rear Overhang mm 425 455 23 Basic Right Angle Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Max. Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0 (Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5 25 Lifting Full load mm/s 600 No load mm/s 680 26 Lowering Full load mm/s 450 No load mm/s 550 28 Max. Drawbar Pull Full load kN 12.7 15.7 12.7 15.7 No load kN 6.9 30 Max. Gradeability* Full load % 25 33 22 31 No load % 18 32 Total Weight kg 2510 2670 33 Weight Distribution Full load Front kg 3510 3880 Rear kg 500 540 34 No load Front kg 1070 1030 Rear kg 1440 1640 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50 - 10 10PR 37 Rear 5.00 - 8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 Backrest Height mm 1045 Overhead Guard Clearance mm 1005 Counterweight Height mm 1110 Drawbar Pin Center Height mm 495 Step Height / Floor Height mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 28 49 Internal Combustion Engine Make/Model NISSAN K21 Rated Horsepower / r.p.m. kW 34.6 / 2250 Rated Torque / r.p.m. N•m 153.5 / 1600 51 Number of Cylinder 4 52 Piston Displacement cc 2065 Alternator output kW/Amp 0.60 / 50 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1 57 Operating Pressure For Attachments MPa (psi) 17.7
Cha
ract
eris
tics
Dim
ensi
ons
Perf
orm
ance
Wei
ght
Cha
ssis
Eng
ine
and
Tra
nsm
issi
on
STANDARD SPECIFICATIONS Gasoline – 2 - 2.5 - 3 ton
*Computed values
Cha
ract
eris
tics
1 Manufacturer TCM2 Model FG20C3 FG20T3 FG25C3 FG25T3 FG30C3 FG30T3
3Load Capacity kg 2000 2500 3000Load Center mm 500 500 500
5 Power type Gasoline Gasoline Gasoline
6 Operator Position Seated Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic Pneumatic8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2 2x / 2
Dim
ensi
ons
9 Maximum Fork Height mm 3000 3000 300010 Free Lift mm 105 110 165
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40 1070 x 125 x 45
Fork Spread (Outside) Max. / Min. mm 1020 / 244 1020 / 244 1090 / 250
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555 2705
16 Overall Width mm 1150 1150 1225
17 Mast Height Fork Lowered mm 2030 2030 2075
18 Mast Height Fork Raised mm 4030 4030 4260
19 Overhead Guard Height (EXB, EXK) mm 2070 2070 2090
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130 2150
20 Operator’s Seat Height mm 1045 1045 1070
21 Turning Radius (Outside) mm 2170 2240 2400
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450 480
Rear Overhang mm 435 505 52523 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995 4185
Perf
orm
ance
24
Speeds
Travel Max. (Fwd. / Rvs.)Full Load km/h 18,5 18,5 19No Load km/h 19 19 19,5
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Eng
ine
& T
rans
mis
sio
n
45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 3049
Internal Combustion Engine
Make - Model NISSAN / K21 NISSAN / K21 NISSAN / K21
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Eng
ine
& T
rans
mis
sio
n
45 Battery Voltage / Capacity (5HR) V / AH 12 / 30 12 / 30 12 / 3049
Internal Combustion Engine
Make - Model NISSAN / K25 NISSAN / K25 NISSAN / K25
57 Operating Pressure For attachment MPa 17,7 17,7 17,7
STANDARD SPECIFICATIONS Diesel -- 1.5 - 1.8 ton
*Computed values
I Manufacturer TCM 2 Model FD15C13 FD15T13 FD18C13 FD18T13 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Diesel 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum Fork Height mm 3000 10 Free Lift mm 155 13 Fork Size L x W x T mm 920 x 100 x 35 Fork Spread (Outside) Max. / Min. mm 920 / 200 14 Tilt Angle Fwd / Bwd deg 6 - 12 15 Length to Fork Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Mast Height Fork Lowered mm 1995 18 Mast Height Fork Raised mm 4030 19 Overhead Guard Height (EXB, EXK) mm 2070 Overhead Guard Height (EXC, EXE, EXN) mm 2130 20 Operator’s Seat Height mm 1015 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks)
Rear Overhang mm 425 455 23 Basic Right Angle Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Max. Full load km/h 13.5 / 13.5 (Fwd/Rvs.) No load km/h 14.0 / 14.0 25 Lifting Full load mm/s 530 No load mm/s 600 26 Lowering Full load mm/s 450 No load mm/s 550 28 Max. Drawbar Pull Full load kN 8.8 13.7 8.8 13.7 No load kN 6.9 30 Max. Gradeability* Full load % 22 24 20 21 No load % 19 16 32 Total Weight kg 2540 2700 33 Weight Distribution Full load Front kg 3530 3900 Rear kg 510 550 34 No load Front kg 1090 1050 Rear kg 1450 1650 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50 - 10 10PR 37 Rear 5.00 - 8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 Backrest Height mm 1045 Overhead Guard Clearance mm 1035 Counterweight Height mm 1110 Drawbar Pin Center Height mm 495 Step Height / Floor Height mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 52 49 Internal Combustion Engine Make/Model KUBOTA D1503 Rated Horsepower / r.p.m. kW 21.3 / 2500 Rated Torque / r.p.m. N•m 98 / 1600 51 Number of Cylinder 3 52 Piston Displacement cc 1499 Alternator output kW/Amp 0.54 / 45 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1 57 Operating Pressure For Attachments MPa (psi) 17.7
Cha
ract
eris
tics
Dim
ensi
ons
Perf
orm
ance
Wei
ght
Cha
ssis
Eng
ine
and
Tra
nsm
issi
on
*Computed values
I Manufacturer TCM 2 Model FHG15C3 FHG15T3 FHG18C3 FHG18T3 3 Load Capacity kg 1500 1750 4 Load Center mm 500 5 Power Type Diesel 6 Operation Position Seated 7 Tire Type Front / Rear Pneumatic 8 Wheels (X=driven) Front / Rear 2X / 2 9 Maximum Fork Height mm 3000 10 Free Lift mm 155 13 Fork Size L x W x T mm 920 x 100 x 35 Fork Spread (Outside) Max. / Min. mm 920 / 200 14 Tilt Angle Fwd / Bwd deg 6 - 12 15 Length to Fork Face mm 2245 2275 16 Overall Width mm 1070 1100 17 Mast Height Fork Lowered mm 1995 18 Mast Height Fork Raised mm 4030 19 Overhead Guard Height (EXB, EXK) mm 2070 Overhead Guard Height (EXC, EXE, EXN) mm 2130 20 Operator’s Seat Height mm 1045 21 Turning Radius (Outside) mm 1980 2010 22 Load Distance mm 395 (Centerline of front axle to front face of forks)
Rear Overhang mm 425 455 23 Basic Right Angle Stacking Aisle Width mm 3685 3715 (Add load length and clearance) 24 Speeds Travel Max. Full load km/h 18.5 / 18.5 19.0 / 19.0 18.5 / 18.5 19.0 / 19.0 (Fwd/Rvs.) No load km/h 19.0 / 19.0 19.5 / 19.5 19.0 / 19.0 19.5 / 19.5 25 Lifting Full load mm/s 620 No load mm/s 680 26 Lowering Full load mm/s 450 No load mm/s 550 28 Max. Drawbar Pull Full load kN 14.7 18.6 14.7 18.6 No load kN 6.9 30 Max. Gradeability* Full load % 25 33 22 31 No load % 18 17 32 Total Weight kg 2620 2780 33 Weight Distribution Full load Front kg 3550 3910 Rear kg 570 620 34 No load Front kg 1110 1060 Rear kg 1510 1720 35 Tires Number Front / Rear 2 / 2 36 Size Front 6.50 - 10 10PR 37 Rear 5.00 - 8 - 8PR 38 Wheelbase mm 1425 39 Tread Front mm 890 920 Rear mm 920 Backrest Height mm 1045 Overhead Guard Clearance mm 1005 Counterweight Height mm 1110 Drawbar Pin Center Height mm 495 Step Height / Floor Height mm 420 / 650 40 Underclearance Min. with load mm 100 41 Center of Wheelbase mm 110 42 Brake Service (Foot) Hydraulic - Foot pedal 43 Parking Mechanical - Hand lever 45 Battery Voltage / Capacity (5HR) V/AH 12 / 64 49 Internal Combustion Engine Make/Model NISSAN DIESEL TD27 - II Rated Horsepower / r.p.m. kW 42.0 / 2400 Rated Torque / r.p.m. N•m 170 / 2300 51 Number of Cylinder 4 52 Piston Displacement cc 2663 Alternator output kW/Amp 0.72 / 60 Fuel Tank Capacity Type lit 50 55 Transmission Type Manual Power-shift Manual Power-shift Stage Fwd.-Rvs 2 - 2 1 - 1 2 - 2 1 - 1 57 Operating Pressure For Attachments MPa (psi) 17.7
Cha
ract
eris
tics
Dim
ensi
ons
Perf
orm
ance
Wei
ght
Cha
ssis
Eng
ine
and
Tra
nsm
issi
on
STANDARD SPECIFICATIONS Diesel -- 2 - 2,5 - 3 - 3,5 ton
Cha
ract
eris
tics
1 Manufacturer TCM2 Model FD20C3 FD20T3 FD25C3 FD25T3
3Load Capacity kg 2000 2500Load Center mm 500 500
5 Power type Diesel Diesel
6 Operator Position Seated Seated
7 Tire Type Front / Rear Pneumatic Pneumatic8 Wheels (X=driven) Front / Rear 2x / 2 2x / 2
Dim
ensi
ons
9 Maximum Fork Height mm 3000 300010 Free Lift mm 105 110
13 Fork Size L x W x T mm 1070 x 122 x 36 1070 x 122 x 40
Fork Spread (Outside) Max. / Min. mm 1020 / 245 1020 / 245
14 Tilt Angle Fwd / Bwd deg 6 / 12 6 / 12
15 Lenght to Fork Face mm 2485 2555
16 Overall Width mm 1150 1150
17 Mast Height Fork Lowered mm 2030 2030
18 Mast Height Fork Raised mm 4030 4030
19 Overhead Guard Height (EXB, EXK) mm 2070 2070
Overhead Guard Height (EXC, EXE, EXN) mm 2130 2130
20 Operator’s Seat Height mm 1045 1045
21 Turning Radius (Outside) mm 2170 2240
22 Load Distance (Centerline of Axle to Front Face of Forks) mm 450 450
Rear Overhang mm 435 50523 Basic Right Angle Stacking Aisle Width (Add load length and clearance)) mm 3925 3995
Perf
orm
ance
24
Speeds
Travel Max. (Fwd. / Rvs.)Full Load km/h 18,5 18 18,5 18No Load km/h 19 18,5 19 18,5
Service (Foot) Hydraulic-Foot pedal Hydraulic-Foot pedal Hydraulic-Foot pedal43 Parking Mechanical-Hand lever Mechanical-Hand lever Mechanical-Hand lever
Eng
ine
& T
rans
mis
sio
n
45 Battery Voltage / Capacity (5HR) V / AH 12 / 64 12 / 64 12 / 6449
Internal Combustion Engine
Make - Model KUBOTA / V3300 KUBOTA / V3300 KUBOTA / V3300
57 Operating Pressure For attachment MPa 17,7 17,7 17,7
The products manufactures at TCM plant got ISO 9001 & 14001 certifi cates
CAPACITY / LOADCENTER
STANDARD EQUIPMENT AND ACCESSORIES
EQUIPMENT
• Adjustable ORS seat with belt• Asbestos-free brake shoe material• Cylinder type bonnet latch with locking
function• Donaldson dry type cyclopac air-cleaner• Drawbar device• Durable overhead guard with resin
screen• Engine auto glow system (Diesel)• Engine idle-up device (Gasoline)• Flow control valve• Fuel water sedimenter (Diesel)• Full hydrostatic power steering• Full transistorized ignition (Gasoline)• Hydraulic oil dipstick• ITA Class Il carriage• J-lug pneumatic industrial tires• Lift circuit cut-off valve• Load backrest• Radiator coolant reservoir• Return hydraulic fi lter• Suction hydraulic strainer• Tilt lock valve• Transmission oil dipstick
(power shift T/M)• Transmission oil fi lter (power shift T/M)• Wide view two stage mast (VM300)• 2-spool control valve with pressure relief• 920mm forks
CONTROLS
• Electric shift control lever (power shift T/M)
• Lift and tilt levers• Multi-function switch lever with self-
cancelling mechanism (Lighting & turn-signal)
• Neutral safety mechanism• Parking brake lever with inter-lock• Tilt adjustable steering post
ACCESSORIES
• Access-assisted hand grip• Back-up buzzer• Back-up lights• Deluxe fl oor mat• Detachle and portable glove box• Electric horn• Front combination lights (turn signal,
clearance)• Head lights - trafi c purpose• High-mounted rear combination lights• Operator tool kit• Pen/ Cup holder• Side view mirrors
INSTRUMENTS AND SWITCH
• Charge indicator• Engine oil pressure warning indicator• Fuel gauge• Fuel water sedimenter indicator (Diesel)• Glow indicator (Diesel)• Hourmeter• Ignition key engine stop (Diesel)• Neutral safety switch• Water temperature gauge
OPTIONAL LOADINGATTACHMENT
EQUIPMENT
• Alternative fork lengths• Alternative lengths fork extension sleeve• Bale clamp• Carton clamp• Crane arm• Drum clamp• Fork clamp• Fork positioner hydraulic type (Intgral)• High, wide type load backrest• Hinged forks/bucket• Load push-pull• Load stabilizer• Ram attachment• Rotating forks (Hook-on/Integral type)• Rotating paper roll clamp
(Hook-on/Integral type)• Side-shifter (Hook-on/Integral)• Sleeve-in hook• Wide type fork carriage• Wide view full free 2-stage (VFM) mast• Wide view full free 3-stage (VFHM) mast
OPTIONAL EQUIPMENT ANDACCESSORIES
EQUIPMENT
• Air Boss tires (TRA)• Auxiliary hydraulic valve modules
(max. 5spool)• Central greasing system (CL)• Color tire (white, green)• Dual element aircleaner (ADE)• Exhaust purify catalystic muffl er (EPM)• Fingertip hydraulic valve control
(max. 4spool) (FIT)• Fishery industry package (FC)• Front dual drive wheels (DD/SDD)• Full open cabine (AW 061)• Head light guard• Heater (HR)• Interlock system (travel & load/unload) (SIL)• Lift lock mechanism (VLL)• LPG exclusive/Dual fuel (LPG - Gasoline)
package• Overhead exhaust system (TUE)• Overhead guard / High profi le 2130mm
(HGH060)• Overhead guard / Low profi le 1995mm
(HGL)• Plate fi n type radiator (RAD PF)• Pre-cleaner engine air intake (CAK B)• Radiator dust screen (fi ne, medium
mesh) (DSR)• Smoke reduction/spark arrester muffl er
(Diesel) (CBM)• Diesel particulate fi lter exhaust system • Power clutch (manual T/M)• Non-slip differential (power shift T/M)• Steering knob auto-return mechanism
(SRS)• Unique cushion tires (SE)
NOTES:• Meets following major standards and code:
ISO 1074 Counter Balanced Lift Trucks, Stability & Safety Test (Int’l)ISO 3691 Powered industrial trucks - safety codeJIS D6001 Industrial Lift Trucks (Japan)JIS D6011 Stability & Safety Test (Japan)
• Overhead guard meets ISO 6055, JIS 6021• ln conformity with provision of the Machinery Directive
98/37/EC, as amended, and with National implemen-ting legislation: (European and Scandinavian export trucks)
• Specifi cations are subject to change without notice and its may vary depending on markets.Please consult your TCM representative for details.
ACCESSORIES
• Custom paint-work• Fire extinguisher (FE)• Rear working light• Rotating warning light (RLY/RLR)• Tilt cylinder boots (TLB)
• Asbestos-free brake shoe material• Donaldson dry type cyclopac air-cleaner• Radiator coolant reservoir• Cylinder type bonnet latch with locking
function• Adjustable ORS seat with belt• Drawbar device• Engine idle-up device (Gasoline)• Engine auto glow system (Diesel)• Fuel water sedimenter (Diesel)• Full hydrostatic power steering• Full transistorized ignition (Gasoline)• Durable overhead guard with resin
screen• Wide view two stage mast (VM300)• Hydraulic oil dipstick• ITA Class II or class Ill carriage• J-lug pneumatic industrial tires• Lift circuit cut-off valve• Load backrest• Flow control valve• Return hydraulic fi lter• Suction hydraulic strainer• Tilt lock valve• Transmission oil dipstick
(power shift T/M)• Transmission oil fi lter (power shift T/M)• lO7Omm forks• 2-spool control valve with pressure relief
CONTROLS
• Electric shift control lever (power shift T/M)
• Lift and tilt levers• Multi-function switch lever with self-
cancelling mechanism (Lighting & turn-signal)
• Parking brake lever with inter-lock• Tilt adjustable steering post• Neutral safety mechanism
ACCESSORIES
• Back-up buzzer• Back-up lights• Deluxe fl oor mat• Pen/ Cup holder• Electric horn• Access-assisted hand grip• Front combination lights (turn signal,
clearance)• Detachle and portable glove box• Head lights - trafi c purpose• High-mounted rear combination lights• Operator tool kit• Side view mirrors
INSTRUMENTS AND SWITCH
• Charge indicator• Engine oil pressure warning indicator• Fuel gauge• Glow indicator (Diesel)• Hourmeter• Ignition key engine stop (Diesel)• Neutral safety switch• Fuel water sedimenter indicator (Diesel)• Water temperature gauge
OPTIONAL LOADINGATTACHMENT
EQUIPMENT
• Bale clamp• Carton clamp• Crane arm• Drum clamp• Fork clamp• Alternative lengths fork extension sleeve• Fork positioner hydraulic type
(Hook-on/Intgral)• Fork positioner manual type• High, wide type load backrest• Hinged forks/bucket• Load push-pull• Load stabilizer• Alternative fork lengths• Ram attachment• Rotating forks (Hook-on/Integral type)• Rotating paper roll clamp
(Hook-on/Integral type)• Side-shifter(Hook-on/Integral)• Sleeve-in hook• Wide type fork carriage• Wide view full free 2-stage (VFM) mast• Wide view full free 3-stage (VFHM) mast• Wide view full free 2-stage 4cyl (VFW)
mast• Wide view full free 3-stage 4cyl (VFHW)
mast• Rotating bale clamp
OPTIONAL EQUIPMENT ANDACCESSORIES
EQUIPMENT
• Auxiliary hydraulic valve modules(max. 5spool)
• Central greasing system (CL)• Color tire (white, green)• Exhaust purify catalystic muffl er (EPM)• Front dual drive wheels (DD/SDD)• Power clutch (manual T/M)• Oil clutch (manual T/M)• Heater (HR)• Heater & defroster (DEF)• LPG exclusive/Dual fuel (LPG - Gasoline)
package• Overhead exhaust system (TUE)• Smoke reduction/spark arrester muffl er • Unique cushion tires (SE)• Windshield wiper• Steel cabin - enclosed type (SCB 001)• Air-conditioner CFC free (AC)• Plate fi n type radiator (RAD PF)• Full open cabine (AW 061)• Radiator dust screen (fi ne, medium
mesh)• Pre-cleaner engine air intake (CAK B)• Dual element aircleaner (ADE)• Overhead guard! High profi le 2130mm• Diesel particulate fi lter exhaust system • Overhead guard! Low profi le 1995mm• Non-slip differential (power shift T/M)• Fishery industry package (FC)• Fingertip hydraulic valve control (FIT)• Cabin - panel type (SCBPA)• Steering knob auto-return mechanism
(SRS)• Lift lock mechanism (VLL)• Interlock system (travel & load/unload)• Load sensing valve (VLS)• High capacity radiator - High power
model (RAD PF2)
NOTES:• Meets following major standards and code:
ISO 1074 Counter Balanced Lift Trucks, Stability & Safety Test (Int’l)ISO 3691 Powered industrial trucks - safety codeJIS D6001 Industrial Lift Trucks (Japan)JIS D6011 Stability & Safety Test (Japan)
• Overhead guard meets ISO 6055, JIS 6021• ln conformity with provision of the Machinery Directive
98/37/EC, as amended, and with National implemen-ting legislation: (European and Scandinavian export trucks)
• Specifi cations are subject to change without notice and its may vary depending on markets.Please consult your TCM representative for details.
ACCESSORIES
• Custom paint-work• Fire extinguisher (FE)• Rear working light• Rotating warning light (RLY/RLR)• Tilt cylinder boots (TLB)