Tool Holder Catalog - INDEX-Werkeinfoshop.index-werke.de/...ABC_Tool-holder-Catalogue_VDI25_en.pdf · Tool Holder Catalog INDEX ABC ... W9990038 Grooving tool holding block, ... W9990154

LL3602.30051 - 10.04.20140414/Rö

Tool Holder Catalog

INDEX ABC

VDI 25

Disclaimer

The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors or based on technical advances.

A Word on Copyright

This document is proprietary and was originally written in German. Its reproduction and distribution in whole or in individual parts without permission of the copyright owner is prohibited and will be prosecuted under criminal or civil law. All rights reserved, including for translation.

© Copyright by INDEX-Werke GmbH & Co. KG Esslingen 2014

© Copyright by TRAUB Drehmaschinen GmbH & Co. KG Reichenbach 2014

Abbreviations used in the catalog:

EC = external cooling lubricant supplyapprox. = approximatelyD = diametermax = maximummin = minimumIC = internal cooling lubricant supplyMT = Morse taperR = radiuss = wrench sizeST = steep taperSQ = square

3For more information, visit http://infoshop.index-werke.de/

Table of Contents ........................................................................................................................................ 0

Technical Information INDEX C100 .......................................................................................................... 1

Usage Information INDEX C100 ................................................................................................................ 2

Tool holder fix, Shank VDI 25 ................................................................................................................. 3

Tool holder live, Shank VDI 25 ................................................................................................................. 4

Tool holder to spring-loaded tap holder, Shank VDI 20 ...................................................................... 5



Tool holder fix, Vee mounting .................................................................................................................. 8

Tool holder live, Vee mounting ................................................................................................................ 9

Tool holder fix, Shank VDI 25, Rear End Machining Unit ................................................................... 10

Tool holder live, Shank VDI 25, Rear End Machining Unit .................................................................. 11

Tool holder fix, Shank 1“, Rear End Machining Unit ............................................................................ 12

Tool holder live, Shank 1“, Rear End Machining Unit .......................................................................... 13

Accessories INDEX ABC ............................................................................................................................. 14

Product notes............................................................................................................................................... 15

For accessories for tool holders visit http://infoshop.index-werke.de/

Table of Contents

4For more information, visit http://infoshop.index-werke.de/

0-1For more information, visit http://infoshop.index-werke.de/

Table of Contents


A-1For more information, visit http://infoshop.index-werke.de/

Catalog page

Technical Information INDEX ABC

Warranty 1-2

Information on wear parts

Inspection of live tool holders and guide bushings

Tool holders with cooling lubricant supply 1-3

Cooling lubricant filtering

Cleaning live tool holders

Speed ratio specifications on tool holders

Direction of rotation specification 1-4

Tightening Torque 1-5

Replacement seals for tool shank

Sealing air port

Tool holders with fixation 1-6

High-pressure unit

Load limits of live tools

Live tool holders 1-7

Weight distribution on turret head 1-8

Collision

Tool change on live tool holders

A-2For more information, visit http://infoshop.index-werke.de/

Catalog page


Information on how to use the chart 1-9when using tool holders

B-1For more information, visit http://infoshop.index-werke.de/

Catalog page

Usage Information INDEX ABC

2-2Structure of the INDEX ABC

2-3Work area INDEX ABC

2-4Work area INDEX ABC

KL9652.70351 2-5Performance chartDriven tools, Tool carrier 1Speed range 0-4500min-1

KL9652.40021 2-6Performance chartDriven tools, Tool carrier 2Speed range 0-6000min-1

Tool holder fixShank VDI 25

Catalog page

For more information see http://infoshop.index-werke.de/ C-1

W1200039 Bar stop, live 3-2Fixation noneMounting D25Cooling –X / Y / Z 70 (2.76) / – / 30 (1.18) mm ('')

W9990159 Bar stop, live 3-3Fixation –Mounting D58Cooling –X / Y / Z – / – / 30 (1.18) mm ('')

W9990160 Bar stop, live 3-4Fixation –Mounting D85Cooling –X / Y / Z – / – / 30 (1.18) mm ('')

W1230000 Compensation holder 3-5Fixation Vee barMounting VDI 20Cooling external and internal, pmax 20 barX / Y / Z 70 (2.76) / – / 2 (0.8) mm ('')

W1230035 Compensation holder 3-6Fixation Vee barMounting VDI 20Cooling external and internal, pmax 40 barX / Y / Z 60 (2.36) / – / 2 (0.8) mm ('')

W1230027 Compensation holder 3-7Fixation Vee barMounting VDI 25Cooling internal, pmax 80 barX / Y / Z 70 (2.76) / – / 2 (0.8) mm ('')

W1230003 Compensation holder 3-8Fixation Vee barMounting VDI 30Cooling internal, pmax 80 barX / Y / Z 60 (2.36) / – / 3 (0.12) mm ('')


Catalog page


W1230026 Compensation holder 3-9Fixation Vee barMounting VDI 30Cooling internal, pmax 80 barX / Y / Z 70 (2.76) / – / -5 (-0.2) mm ('')

W1230025 Compensation holder 3-10Fixation Vee barMounting D1''Cooling external, pmax 80 barX / Y / Z 60 (2.36) / – / 15 (0.59) mm ('')

W1200042 Drilling tool holder, Specially for the marking tool WriteStar 3-11Fixation noneMounting D12Cooling –X / Y / Z 68 (2.68) / – / – mm ('')

W1230036 Drilling tool holder 3-12Fixation Vee barMounting ER 16Cooling external, pmax 20 barX / Y / Z 60 (2.36) / – / – mm ('')

W1230054 Drilling tool holder 3-13Fixation Vee barMounting ER 25Cooling external and internal, pmax 80 barX / Y / Z 60 (2.36) / – / 31 (1.22) mm ('')


W1230055 Drilling tool holder 3-15Fixation Vee barMounting ER 32Cooling external and internal, pmax 80 barX / Y / Z 60 (2.36) / – / 52 (25) mm ('')


Catalog page


W1230007 Drilling tool holder, vertically adjustable 3-16Fixation Vee barMounting DIN 1835 B/E D16Cooling internal, pmax 80 barX / Y / Z 70 (2.76) / – / 25 (0.98) mm ('')

W1230046 Drilling tool holder 3-17Fixation Vee barMounting DIN 1835 B/E D32Cooling external and internal, pmax 80 barX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')


W1230032 Drilling tool holder 3-19Fixation Vee barMounting D12Cooling external and internal, pmax 20 barX / Y / Z 70 (2.76) / – / 30 (1.18) mm ('')

W1210001 Drilling tool holder, vertically adjustable 3-20Fixation Setting gaugeMounting D16Cooling internal, pmax 80 barX / Y / Z 60 (2.36) / ±1.5 (±06) / 30 (1.18) mm ('')

W1200000 Turning tool holder, Form C1/C4 3-21Fixation noneMounting square 16x16Cooling external, pmax 20 barX / Y / Z 55 (2.17) / – / 19 (0.75) mm ('')



Catalog page




W1200025 Turning tool holder, double 3-25Fixation noneMounting square 20x20Cooling external, pmax 20 barX / Y / Z 55 (2.17) / – / 17 (0.67) mm ('')

W1200021 Turning tool holder, Form C2/C3 3-26Fixation noneMounting square 3/4x3/4''Cooling internal, pmax 20 barX / Y / Z 55 (2.17) / – / 19 (0.75) mm ('')

W1200022 Turning tool holder, Form C1/C4 3-27Fixation noneMounting square 3/4x3/4''Cooling internal, pmax 20 barX / Y / Z 55 (2.17) / – / 15 (0.59) mm ('')

W1220007 Turning tool holder 3-28Fixation Clamping and stop barMounting square 20x20Cooling external, pmax 80 barX / Y / Z 40 (1.57) / – / 30 (1.18) mm ('')

W1230016 Turning tool holder 3-29Fixation Vee barMounting square 20x20Cooling external, pmax 40 barX / Y / Z 18.5 (0.73) / – / 30 (1.18) mm ('')


Catalog page


W1230021 Turning tool holder 3-30Fixation Vee barMounting square 20x20Cooling external, pmax 40 barX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')

W1230029 Turning tool holder 3-31Fixation Vee barMounting square 20x20Cooling external, pmax 80 barX / Y / Z 18.5 (0.73) / – / 30 (1.18) mm ('')

W1230031 Turning tool holder 3-32Fixation Vee barMounting square 20x20Cooling external, pmax 80 barX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')

W1230020 Basic holder, vertically adjustable 3-33Fixation Vee barMounting –Cooling external and internal, pmax 20 barX / Y / Z 35 (1.38) / – / 5 (0.2) mm ('')

W9990038 Grooving tool holding block, vertically adjustable 3-34Fixation –Mounting Trapezoid 32x5Cooling –, pmax 20 barX / Y / Z 60 (2.36) / – / 32 (1.26) mm ('')


W9990064 Grooving tool holding block, vertically adjustable 3-36Fixation –Mounting square 16x16Cooling –X / Y / Z 40 (1.57) / – / 40 (1.57) mm ('')


Catalog page


W9990066 Grooving tool holding block, vertically adjustable 3-37Fixation –Mounting Trapezoid 26x5Cooling –X / Y / Z 47.5 (1.87) / – / 32 (1.26) mm ('')


W9990068 Grooving tool holding block, vertically adjustable 3-39Fixation –Mounting Trapezoid 26x5Cooling –X / Y / Z 47.5 (1.87) / – / 28.5 (1.12) mm ('')






Catalog page



W9990074 Grooving tool holding block, vertically adjustable 3-45Fixation –Mounting Trapezoid 16x3Cooling –X / Y / Z 20 (0.79) / – / 25 (0.98) mm ('')



W9990154 Knurling tool holder 3-48Fixation noneMounting D6Cooling –X / Y / Z 38 (1.5) / – / 20 (0.79) mm ('')

W1230004 Basic holder 3-49Fixation Vee barMounting –Cooling external and internal, pmax 20 barX / Y / Z 70 (2.76) / – / -5 (-0.2) mm ('')

W9990085 Drill holding block 3-50Fixation –Mounting ER 25Cooling internal, pmax 20 barX / Y / Z 42.5 (1.67) / – / – mm ('')


Catalog page


W9990086 Drill holding block 3-51Fixation –Mounting D20Cooling external, pmax 20 barX / Y / Z 40 (1.57) / – / – mm ('')

W1200008 Scroll holder 3-52Fixation noneMounting –Cooling internal, pmax 20 barX / Y / Z 65 (2.56) / – / 40.5 (1.59) mm ('')

W1200036 Calibrating tool 3-53Fixation noneMounting –Cooling –X / Y / Z 110 (4.33) / – / – mm ('')

W1200009 Blanking plug 3-54Fixation –Mounting –Cooling –X / Y / Z 10 (0.39) / – / – mm ('')

W1200026 Coolant nozzle 3-55Fixation noneMounting –Cooling –X / Y / Z 16 (0.63) / – / – mm ('')

Tool holder liveShank VDI 25

Catalog page

For more information see http://infoshop.index-werke.de/ D-1

W1235047 Drilling unit 4-2Fixation Vee barMounting ER 11Cooling external, pmax 20 barSpeed ratio 1:3 (0.333)X / Y / Z 75 (2.95) / – / 15 (0.59) mm ('')

W1235049 Drilling unit 4-3Fixation Vee barMounting ER 11Cooling external, pmax 20 barSpeed ratio 1:1.33 (0.75)X / Y / Z 70 (2.76) / – / 17.5 (0.69) mm ('')

W1205022 Drilling unit 4-4Fixation noneMounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)X / Y / Z 54 (2.13) / – / 0 mm ('')

W1205025 Milling unit 4-5Fixation noneMounting D16Cooling external, pmax 40 barSpeed ratio 4.5:1 (4.5)X / Y / Z 82 (3.23) / – / 0 mm ('')

W1225010 Milling unit 4-6Fixation Clamping and stop barMounting Milling tool mounting D22Cooling external, pmax 20 barSpeed ratio 2:1 (2)X / Y / Z 74 (2.91) / – / 45 (1.77) mm ('')

W1205018 Tapping unit, extendable 4-7Fixation noneMounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)X / Y / Z 60 (2.36) / – / 0 mm ('')

W1235053 Circular saw unit 4-8Fixation Vee barMounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)X / Y / Z 68 (2.68) / – / 0 mm ('')


Catalog page


W1235045 Drilling unit 4-9Fixation Vee barMounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1 (1)X / Y / Z 70 (2.76) / – / 53 (29) mm ('')

W1235046 Drilling unit 4-10Fixation Vee barMounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1 (1)X / Y / Z 60 (2.36) / – / 53 (29) mm ('')

W1235058 Drilling unit 4-11Fixation Vee barMounting ER 20Cooling external, internal optional, pmax 20 barSpeed ratio 2:1 (2)X / Y / Z 70 (2.76) / – / 53 (29) mm ('')

W1235042 Drilling unit 4-12Fixation Vee barMounting DIN 1835 E D16Cooling internal, pmax 40 barSpeed ratio 1:2 (0.5)X / Y / Z 60 (2.36) / – / 79 (3.11) mm ('')

W1235044 Milling unit 4-13Fixation Vee barMounting D10Cooling external, pmax 40 barSpeed ratio 2.09:1 (2.09)X / Y / Z 55 (2.17) / – / 55 (2.17) mm ('')

W1235052 Milling unit 4-14Fixation Vee barMounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2.09:1 (2.09)X / Y / Z 55 (2.17) / – / 47.5 (1.87) mm ('')

W1225008 Tapping unit, extendable 4-15Fixation Clamping and stop barMounting ER 20Cooling external, pmax 40 barSpeed ratio 2:1 (2)X / Y / Z 70 (2.76) / – / 78 (37) mm ('')


Catalog page


W1235051 Broaching/ Slotting unit 4-16Fixation Vee barMounting D20Cooling external, pmax 40 barSpeed ratio 1:1 (1)X / Y / Z 60 (2.36) / – / 75 (2.95) mm ('')

W1235050 Drilling unit 4-17Fixation Vee barMounting ER 11Cooling external, pmax 40 barSpeed ratio 1:1.7 (0.588)X / Y / Z 44 (1.73) / – / 37 (1.46) mm ('')

W9990040 Milling cutter holding block 4-18Fixation –Mounting Milling tool mounting D13Cooling –X / Y / Z – / – / – mm ('')





Tool holder to spring-loaded tap holderShank VDI 20

Catalog page

For more information see http://infoshop.index-werke.de/ E-1

W1100017 Bar stop, adjustable, live 5-2Fixation noneMounting –Cooling –X / Y / Z 49.5 - 71.5 (1.95 - 2.81) / – / – mm ('')

W1100006 Drilling tool holder 5-3Fixation noneMounting ER 16Cooling internal, pmax 20 barX / Y / Z 42.5 (1.67) / – / – mm ('')

W1100007 Drilling tool holder, Form E4 5-4Fixation noneMounting ER 25Cooling internal, pmax 80 barX / Y / Z 51 (21) / – / – mm ('')

W1100010 Drilling tool holder, Form E4 5-5Fixation noneMounting ER 40Cooling internal, pmax 20 barX / Y / Z 66.5 (2.62) / – / – mm ('')

W1100004 Drilling tool holder, Form E1 5-6Fixation noneMounting DIN 1835 B/E D20Cooling internal, pmax 20 barX / Y / Z 48 (1.89) / – / – mm ('')

W1100005 Drilling tool holder, Form E1 5-7Fixation noneMounting DIN 1835 B/E D25Cooling internal, pmax 80 barX / Y / Z 56.5 (2.22) / – / – mm ('')

W1100018 Drilling tool holder, Form E2 5-8Fixation noneMounting D10Cooling external, pmax 20 barX / Y / Z 50 (1.97) / – / – mm ('')


Catalog page



W1100001 Drilling tool holder 5-10Fixation noneMounting D15Cooling external, pmax 20 barX / Y / Z 26 (12) / – / – mm ('')


W1100009 Drilling tool holder 5-12Fixation noneMounting D25Cooling external, pmax 20 barX / Y / Z 43 (1.69) / – / – mm ('')

W1100002 Basic holder, vertically adjustable 5-13Fixation noneMounting –Cooling internal, pmax 20 barX / Y / Z 14 (0.55) / – / – mm ('')

W9990085 Drill holding block 5-14Fixation –Mounting ER 25Cooling internal, pmax 20 barX / Y / Z 42.5 (1.67) / – / – mm ('')

W9990086 Drill holding block 5-15Fixation –Mounting D20Cooling external, pmax 20 barX / Y / Z 40 (1.57) / – / – mm ('')


Catalog page


W1100014 Center holder, elastic, live, Center replaceble 5-16Fixation noneMounting MK0Cooling –X / Y / Z 66 (2.6) / – / – mm ('')

W1100013 Center holder, elastic, live 5-17Fixation noneMounting –Cooling –X / Y / Z 65 (2.56) / – / – mm ('')

W1100011 Tapping tool holder, over-running 5-18Fixation noneMounting D12Cooling external, pmax 20 barX / Y / Z 56 (2.2) / – / – mm ('')

W1100003 Tapping tool holder 5-19Fixation noneMounting D18Cooling external, pmax 20 barX / Y / Z 50.5 (1.99) / – / – mm ('')

W1100012 Reaming tool holder, adjustable 5-20Fixation noneMounting D12Cooling external, pmax 20 barX / Y / Z 52 (25) / – / – mm ('')

W1100016 Broaching/ Slotting tool holder, rotating, live 5-21Fixation noneMounting D12Cooling external, pmax 20 barX / Y / Z 66 (2.6) / – / – mm ('')



Catalog page

For more information see http://infoshop.index-werke.de/ F-1

W1200006 Drilling tool holder, Form E4 6-2Fixation noneMounting ER 25Cooling internal, pmax 40 barX / Y / Z 57 (2.24) / – / – mm ('')






W1200020 Drilling tool holder, Form E2 6-8Fixation noneMounting D8Cooling external and internal, pmax 80 barX / Y / Z 50 (1.97) / – / – mm ('')


Catalog page








W9990095 Compensation bushing 6-15Fixation noneMounting D3/4''Cooling –X / Y / Z 6 (0.24) / – / – mm ('')


Catalog page


W1200007 Tapping tool holder, extendable 6-16Fixation noneMounting DIN 1835 B/E D18Cooling external, pmax 20 barX / Y / Z 50 (1.97) / – / – mm ('')

W1200028 Reaming tool holder 6-17Fixation noneMounting ER 16Cooling external, pmax 20 barX / Y / Z 63 (2.48) / – / – mm ('')




Catalog page

For more information see http://infoshop.index-werke.de/ G-1

W1300037 Bar stop, adjustable, live 7-2Fixation noneMounting –Cooling –X / Y / Z 60 - 97 (2.36 - 3.82) / – / – mm ('')

W1300038 Bar stop, adjustable, live 7-3Fixation noneMounting –Cooling –X / Y / Z 60 - 97 (2.36 - 3.82) / – / – mm ('')


W9990094 Compensation bushing 7-5Fixation noneMounting D1''Cooling –X / Y / Z 6 (0.24) / – / – mm ('')

W1300023 Compensation holder 7-6Fixation noneMounting D1''Cooling internal, pmax 20 barX / Y / Z 60 (2.36) / – / – mm ('')




Catalog page



W1300057 Drilling tool holder, Form E1 7-10Fixation noneMounting DIN 1835 E D20Cooling internal, pmax 80 barX / Y / Z 67 (2.64) / – / – mm ('')

W1300058 Drilling tool holder, Form E1 7-11Fixation noneMounting DIN 1835 E D25Cooling internal, pmax 80 barX / Y / Z 71 (2.8) / – / – mm ('')






Catalog page





W1300053 Drilling tool holder 7-19Fixation noneMounting D25Cooling external and internal, pmax 40 barX / Y / Z 45 (1.77) / – / – mm ('')


W1300022 Drilling tool holder 7-21Fixation noneMounting D32Cooling internal, pmax 80 barX / Y / Z 73 (2.87) / – / – mm ('')

W1300027 Drilling tool holder 7-22Fixation noneMounting MK1Cooling external, pmax 20 barX / Y / Z 30 (1.18) / – / – mm ('')


Catalog page


W1300028 Drilling tool holder 7-23Fixation noneMounting MK2Cooling external, pmax 20 barX / Y / Z 27 (16) / – / – mm ('')

W1300029 Drilling tool holder 7-24Fixation noneMounting MK3Cooling external, pmax 20 barX / Y / Z 45 (1.77) / – / – mm ('')

W1300012 Basic holder, vertically adjustable 7-25Fixation noneMounting –Cooling external, pmax 20 barX / Y / Z 14 (0.55) / – / – mm ('')

W9990092 Drill holding block 7-26Fixation –Mounting ER 25Cooling –, pmax 40 barX / Y / Z 30 (1.18) / – / – mm ('')

W9990093 Drill holding block 7-27Fixation –Mounting D32Cooling –, pmax 40 barX / Y / Z 57 (2.24) / – / – mm ('')

W1300004 Center holder, live 7-28Fixation noneMounting D15.4/Cone 1:7.5Cooling –X / Y / Z 69.5 (2.74) / – / – mm ('')

W1300005 Center holder, elastic, live 7-29Fixation noneMounting D15.4/Cone 1:7.5Cooling –X / Y / Z 68.5 (2.7) / – / – mm ('')


Catalog page


W1300030 Tapping tool holder, extendable 7-30Fixation noneMounting D25Cooling external, pmax 20 barX / Y / Z 73 (2.87) / – / – mm ('')

W1300031 Reaming tool holder, adjustable 7-31Fixation noneMounting ER 25Cooling external, pmax 20 barX / Y / Z 73.5 (2.89) / – / – mm ('')

W1300032 Reaming tool holder, adjustable 7-32Fixation noneMounting D18Cooling external, pmax 20 barX / Y / Z 59 (2.32) / – / – mm ('')

W1300065 Reaming tool holder, self-centering 7-33Fixation noneMounting D20Cooling internal, pmax 40 barX / Y / Z 93 (3.66) / – / – mm ('')


Tool holder fixVee mounting

Catalog page

For more information see http://infoshop.index-werke.de/ H-1

W8900003 Bar stop, adjustable 8-2Fixation noneMounting –Cooling –X / Y / Z 85 (3.35) / – / -17 (-0.67) mm ('')

W8900014 Bar stop, adjustable, live 8-3Fixation noneMounting –Cooling –X / Y / Z 85 (3.35) / – / -65 (-2.56) mm ('')

W8900001 Turning tool holder, double 8-4Fixation noneMounting square 20x20Cooling external, pmax 20 barX / Y / Z 65 (2.56) / – / 0 mm ('')

W8900002 Turning tool holder 8-5Fixation noneMounting square 20x20Cooling external, pmax 20 barX / Y / Z 85 (3.35) / – / 0 mm ('')

W8900006 Basic holder, Contour plunging tool holder 8-6Fixation noneMounting –Cooling external, pmax 40 barX / Y / Z 45.5 (1.79) / – / 9 (0.35) mm ('')

W9990244 Grooving tool holding block, adjustable 8-7Fixation –Mounting –Cooling –X / Y / Z 40 (1.57) / – / – mm ('')

W8900007 Basic holder, angle-adjustable 8-8Fixation noneMounting –Cooling external, pmax 40 barX / Y / Z 42 (1.65) / – / 0 mm ('')


Catalog page


W9990055 Grooving tool holding block, vertically adjustable 8-9Fixation –Mounting –Cooling external, pmax 20 barX / Y / Z 30 (1.18) / – / – mm ('')

W9990065 Grooving tool holding block, vertically adjustable 8-10Fixation –Mounting –Cooling external, pmax 20 barX / Y / Z 38 (1.5) / – / – mm ('')

W8900013 Basic holder, adjustable 8-11Fixation noneMounting –Cooling external, pmax 40 barX / Y / Z 52 (25) / – / 10 (0.39) mm ('')

W9990245 Grooving tool holding block, adjustable 8-12Fixation –Mounting square 20x20Cooling –X / Y / Z 37 (1.46) / – / 28 (1.10) mm ('')

W9990246 Grooving tool holding block, adjustable 8-13Fixation –Mounting square 20x20Cooling –X / Y / Z 45 (1.77) / – / 28 (1.10) mm ('')




Catalog page










Catalog page



W9990154 Knurling tool holder 8-24Fixation noneMounting D6Cooling –X / Y / Z 38 (1.5) / – / 20 (0.79) mm ('')

W8900005 Basic holder, vertically adjustable 8-25Fixation noneMounting –Cooling external and internal, pmax 20 barX / Y / Z 62 (2.44) / – / -30 (-1.18) mm ('')

W9990242 Drill holding block, horizontally adjustable 8-26Fixation –Mounting D1''Cooling –, pmax 20 barX / Y / Z 23.55 (0.93) / – / 50 (1.97) mm ('')

W9990045 Drill holding block 8-27Fixation –Mounting D25Cooling –X / Y / Z 23.55 (0.93) / – / – mm ('')

W9990243 Drill holding block 8-28Fixation noneMounting D25Cooling external, pmax 20 barX / Y / Z 33.55 (1.32) / – / 50 (1.97) mm ('')

W8900009 Center holder, elastic 8-29Fixation –Mounting MK1Cooling –X / Y / Z 85 (3.35) / – / -71 (-2.8) mm ('')


Catalog page


W8900010 Scroll holder 8-30Fixation –Mounting –Cooling –, pmax 40 barX / Y / Z 90 mm (3.54 '') / – / – mm ('')

W8900012 Calibrating tool 8-31Fixation noneMounting D40Cooling –X / Y / Z 110 (4.33) / – / 0 mm ('')

W8900000 Cover plate, Steel 8-32Fixation noneMounting –Cooling –X / Y / Z 12 (0.47) / – / – mm ('')

Tool holder liveVee mounting

Catalog page

For more information see http://infoshop.index-werke.de/ I-1

W8905002 Drilling unit 9-2Fixation noneMounting ER 11Cooling external, pmax 20 barSpeed ratio 1:1.33 (0.75)X / Y / Z 87 (3.43) / – / 1.5 (06) mm ('')

W8905004 Drilling unit, vertically adjustable 9-3Fixation noneMounting ER 16Cooling external, pmax 20 barSpeed ratio 1:1.93 (0.518)X / Y / Z 105 (4.13) / – / 37.5 (1.48) mm ('')

W8905000 Drilling unit 9-4Fixation noneMounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)X / Y / Z 64 (2.52) / – / -16.5 (-0.65) mm ('')

W8905001 Milling unit 9-5Fixation noneMounting DIN 1835 B/E D16Cooling external, pmax 40 barSpeed ratio 4.5:1 (4.5)X / Y / Z 96 (3.78) / – / -16.5 (-0.65) mm ('')

W8905005 Drilling unit 9-6Fixation noneMounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1.13 (0.8857)X / Y / Z 85 (3.35) / – / 36.5 (1.44) mm ('')

W8905003 Drilling unit, angle-adjustable 9-7Fixation noneMounting ER 11Cooling external, pmax 40 barSpeed ratio 1:1.7 (0.588)X / Y / Z 62 (2.44) / – / 53.5 (2.11) mm ('')

Tool holder fixShank VDI 25, Rear End Machining Unit

Catalog page

For more information see http://infoshop.index-werke.de/ J-1









Catalog page










Catalog page


W1200007 Tapping tool holder, extendable 10-16Fixation noneMounting DIN 1835 B/E D18Cooling external, pmax 20 barX / Y / Z 50 (1.97) / – / – mm ('')

W1200028 Reaming tool holder 10-17Fixation noneMounting ER 16Cooling external, pmax 20 barX / Y / Z 63 (2.48) / – / – mm ('')



Tool holder liveShank VDI 25, Rear End Machining Unit

Catalog page

For more information see http://infoshop.index-werke.de/ K-1



W1235054 Circular saw unit 11-4Fixation Vee barMounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)X / Y / Z 68 (2.68) / – / 0 mm ('')

Tool holder fixShank 1", Rear End Machining Unit

Catalog page

For more information see http://infoshop.index-werke.de/ L-1

W6290001 Drilling tool holder 12-2Fixation noneMounting ER 25Cooling –X / Y / Z 22 (0.87) / – / – mm ('')

W6290020 Drilling tool holder 12-3Fixation noneMounting ER 25Cooling internal, pmax 40 barX / Y / Z 50 (1.97) / – / 0 mm ('')

W6290019 Drilling tool holder 12-4Fixation noneMounting DIN 1835 B/E D25Cooling internal, pmax 40 barX / Y / Z 56 (2.2) / – / 0 mm ('')

W6290018 Drilling tool holder, adjustable 12-5Fixation noneMounting D18Cooling internal, pmax 20 barX / Y / Z 56 (2.2) / ±2 (±08) / ±2 (08) mm ('')

W6290000 Drilling tool holder 12-6Fixation noneMounting D25Cooling –X / Y / Z 40 (1.57) / – / – mm ('')

W6290015 Drilling tool holder 12-7Fixation noneMounting MK1Cooling –X / Y / Z 16 (0.63) / – / – mm ('')

W6290016 Drilling tool holder 12-8Fixation noneMounting MK2Cooling –X / Y / Z 29 (1.14) / – / – mm ('')


Catalog page


W6290008 Center holder, elastic, live 12-9Fixation noneMounting D18Cooling –X / Y / Z 72.5 (2.85) / – / – mm ('')

W6290007 Center holder, elastic, live 12-10Fixation noneMounting MK1Cooling –X / Y / Z 72.5 (2.85) / – / – mm ('')

W6290002 Tapping tool holder, extendable 12-11Fixation noneMounting D25Cooling –X / Y / Z 52 (25) / – / – mm ('')

W6290003 Tapping tool holder, over-running 12-12Fixation noneMounting D25Cooling –X / Y / Z 56 (2.2) / – / – mm ('')

W6290005 Reaming tool holder, adjustable 12-13Fixation noneMounting ER 25Cooling –X / Y / Z 55 (2.17) / – / – mm ('')

W6290006 Reaming tool holder, adjustable 12-14Fixation noneMounting D18Cooling –X / Y / Z 41 (1.61) / – / – mm ('')

W6290011 Broaching/ Slotting tool holder, rotating, live 12-15Fixation noneMounting D12Cooling –X / Y / Z 58 (2.28) / – / – mm ('')


Catalog page


W6290012 Broaching/ Slotting tool holder, rotating, live 12-16Fixation noneMounting D20Cooling –X / Y / Z 76 (2.99) / – / – mm ('')

W6290010 Broaching/ Slotting tool holder, rotating, live 12-17Fixation noneMounting D30Cooling –X / Y / Z 78 - 88 (37 - 3.46) / – / – mm ('')

W6290009 Broaching/ Slotting tool holder 12-18Fixation noneMounting D50Cooling –X / Y / Z 80 - 90 (3.2 - 3.54) / – / – mm ('')

W6290017 Guide holder 12-19Fixation noneMounting –Cooling –X / Y / Z 57 (2.24) / – / – mm ('')

W9990176 Roller holding block, adjustable 12-20Fixation –Mounting –Cooling –X / Y / Z – / – / – mm ('')

W9990177 Roller holding block, adjustable 12-21Fixation –Mounting –Cooling –X / Y / Z – / – / – mm ('')

W6290004 Knurling tool holder, adjustable 12-22Fixation noneMounting D6-36Cooling –X / Y / Z – / – / – mm ('')

Tool holder liveShank 1", Rear End Machining Unit

Catalog page

For more information see http://infoshop.index-werke.de/ M-1



W6295002 Circular saw unit 13-4Fixation noneMounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)X / Y / Z 75 (2.95) / ±12.5 (±0.49) / 0 mm ('')

Z-1For more information, visit http://infoshop.index-werke.de/

Catalog page W67501.2050 14-2IC Attachmentfor internal cooling lubricant supply, 20 bar

W67500.5044 14-3IC Attachmentfor internal cooling lubricant supply, 20 bar

W31400.46 14-4Steel Blockfor form cutting tool

W67101.0050 14-5Setting gauge

W9990241 14-6Turning tool holder

W9990997 14-7Locking plate

AZ4005.03 14-8Replacement Seals for Tool Shank

Accessories INDEX ABC


Catalog page AZ4019.00 14-9Sealing Washer and Mounting Pin

Accessories INDEX ABC


Catalog page W9800001EN 15-2Product noteExternal/internal cooling lubricant supplyDrill holder with cylindrical shank tool mountingOffset set screws

W9800004EN 15-3Product noteWritestar

W9800005EN 15-4Product noteExternal/internal cooling lubricant supplyDrill holder with collet chuckOffset set srew

Product notes


Technical InformationINDEX ABC


Warranty

When using tool holders that have not been set, checked and labeled accordingly by INDEX TRAUB, warranty is not applicable to the tool drive.

Information on wear parts

Tool holders and guide bushings are wear parts requiring correct handling. In order to ensure a long service life, compressed air or coolant must not enter the gap seals of the holders or of the guide bushings.

Inspection of live tool holders and guide bushings

Tool holders and guide bushings must be inspected at regu-lar intervals (at least twice a year) for smooth running and play.

The drive pinion and drive clutch of the live tool holders must be subjected to a visual inspection for damage or wear.

If one of the above-mentioned defects is detected during the inspection of the tool holders or guide bushings, they must be returned immediately for preventive maintenance or repair to the following address:

TRAUB Drehmaschinen GmbH & Co. KGHauffstrasse 4D-73262 Reichenbach, GermanyPhone +49 (0) 7153 [email protected]




Tool holders with cooling lubricant supply

Tool holders marked with this symbol must be operated with cooling lubricant (no dry run permitted).

Tool holders marked with this symbol must be operated with cooling lu-bricant when converting from external cooling lubricant supply to internal cooling lubricant supply. Observe dry run capability of IC attachment!

Cooling lubricant filtering

When using live tool holders with internal cooling lubricant supply, it is necessary to use a cooling lubricant filter system with a retained particle size ≤ 50 μ.

Cleaning live tool holders

Live tool holders must never be immersed in cleaning fluid since mixing the cleaning fluid with the bearing grease will reduce the service life of the tool holders.

Speed ratio specifications on tool holders

The value to be programmed is specified in the documentation and on the live tool holders ( = the input in the NC program).

nprog = ntool x i

ntool = speed at cutting tool edge

nPROG

= speed to be programmed

i = speed ratio in the tool holder

This means: the speed increase or speed reduction is not specified as a fraction but as a number. This gives speed increase ratios as numbers smaller than 1. Example: i = 0.333 (corresponds to i = 1:3) i = 0.676 (corresponds to i = 1:1.48) Step-down ratios result in numbers >1 For example: i = 2 (corresponds to i = 2:1) i = 1.333 (corresponds to i = 4:3)

M04

M03


Direction of rotation specification

Definition of the viewing direction.Viewing direction for determining the direction of rotation is always from behind (that is, from the drive direction) toward the shaft.

On the machine side, the direction of rotation has been set by parameters such that M03 always denotes clockwise rotation and M04 counter-clockwise run at the interface of the drive pinion of the tool holder.

The direction of rotation given on the holder thus always refers to a "change in direction within a holder". M03 and M04 are machine functions to be programmed. The and arrows indicate the direction of rotation of the cutting edges.

This means:

No reversal of direction of rotationWhen the holder drive shaft has the same direction of rotation as the tool cutting edge, the clockwise direction of run must be specified by M03 (clockwise rotation). Accordingly, counter-clockwise run must be specified by M04.

Reversal of direction of rotationWhen the holder drive shaft has the opposite direction of rotation as the tool cutting edge, the clockwise direction of rotation must be specified by M04. Accordingly, counter-clockwise run must be specified by M03.

Example

No reversal of direction of rotation

M03 M04

M04 M03



Tightening torque

The gaskets on the tool shank and the coolant bushing must be regularly checked for damages.

The tightening torques of the clamping pieces to the tool holder mount-ing depends on the shank diameter of the tool holder.

Shank size Tightening torque

Ø 20mm 8 Nm

Ø 25mm 20 Nm

Ø 30mm 25 Nm

Ø 40mm 40 Nm

Replacement seals for tool shank

See the accessories.

The gaskets on the tool shank and the coolant bushing must be regu-larly checked for damages.

Sealing air port

It must be ensured on all machines with sealing air ports that the sealing air ports in the tool carrier and in the tool holders are sealed/closed with M5x6 mm set screws.




Tool holders with fixation

Except for very few cases, all tool holders have been pre-adjusted with high precision and sealed with the INDEX V bar / TRAUB adjusting bar / W-serration. This setting must not be changed.

The INDEX V bar / TRAUB adjusting bar / W-serration ensures positional accuracy of the tool when re-inserted. The tool holders are fixed around the shank axis by pins (DIN 69880).

DIN holders can be used.

Double serration of the tool holders allows several uses.

High-pressure unit

The cooling lubricant up to 80 bar (e.g., for deep-hole drill-ing) is supplied through the standard cooling lubricant line.

Load limits of live tools

The drive power and torques are indicated in the performance charts. These values represent the upper limit of the calculated theoretical per-formance values (average values). In case of interrupted cuts, e.g., for milling, the load peaks occurring when the cutting edge enters the ma-terial may be much higher than the theoretical torque according to the performance chart.

The cutter should be selected so that a cutting edge is con-stantly being used for cutting during the machining process.


Live tool holders

Only the tool located in the working position is live.

The live tool holders are inserted into the mounting bores in the tool carriers just like non-live tool holders.

Each turret station can accept one live tool.The motor drives the tool that is exclusively in working position. In ad-dition, the index drive is actuated by switching using the same motor.

The sealing washer (1) must be removed first.

For a list of sealing washers, see drawing AZ4019.00 in Chapter “Ac-cessories”.

1

2

Sealing washer

Blanking plug

Before using the machine, make sure that all mounting bores without a tool have been closed with a sealing washer and that the gasket on all tool holders is not dam-aged.

Any mounting bores not used must be closed with blank-ing plugs during machining processes.




Weight distribution on turret head

Tool holders may have considerably different weights de-pending on their function and equipment. Therefore, be sure to balance the tool holders evenly around the turret head when tooling.

Collision

After a collision has occurred, check whether the tool carrier has been displaced. If this is the case, the tool carrier must be realigned to ensure that the drive and tool holder gears accurately engage with each other.

Tool change on live tool holders

To avoid damaging or changing the adjustment of the drive train in the tur-ret, tools must not be changed on the live tool holders inserted in the turret. Tools in live tool holders must be changed outside the machine.



Information on how to use the chart when using tool holders

The chart relates to the output speed n of the tool unit. The tool speed can be read directly from the chart only if the internal speed ratio i in the tool holder is 1:1. For tool holders (VDI holders) with an internal speed ratio i ≠ 1, the output speed n of the tool unit to be programmed must be calculated from the required tool speed and the speed ratio i. Afterwards, the actual powers or torques can be read off or determined.

Example (at 100% duty cycle):

Torq

ue M

dat

out

put

of u

nit

(Nm

)

Pow

er P

(kW

)

Speed n1at output of unit (rpm)

Md

P

0.82.0

0.41.0

0.60.674

1.51.6

0.20.5

1.02.5

0.00.00 1000 2000 3000 4000 5000 6000

The speed ratio and the technical data of each tool holder are indicated on the next pages.

live tool unit, tool speed nTool = 1000 rpm

Internal speed ratio i of the tool holder i = 4

Programmed speed nprog for the drive of the unit

nprog = nTool x i =

1000 rpm x 4 = 4000 rpm

Torque MTool at the output of the tool holder

Read-out Md at speed nprog = 4000 rpm = 1.6 NmMd = MTool : i Formula changed: MTool = Md x i = 1.6 Nm x 4 = 6.4 Nm

Power P at the output of the tool holder ≈ Power P at the output of the setup

Read-out at 4000 rpm –> P = 0.67 kWcalculated: P = 2 x π x nprog x MdP = 2 x π x 4000 x 1.6 Nm = 0.67 kW 60 x 1000



Usage Information

INDEX ABC

Structure of the INDEX ABC

Tool mounting VDI 25


134

5

2

1 Tool carrier 1 XZ2 Tool carrier 2 XZ3 Synchronous spindle4 Rear End Machining Unit5 Main spindle


Work area INDEX ABC


Tool carrier 1

Rear EndMachining Units

Tool carrier 2

Main spindle


Work area INDEX ABC


Tool carrier 1

Tool carrier 2

Rear End Machining Units

Main spindle


Performance chart

Driven tools, Tool carrier 1

Speed range 0-4500min-1

KL9652.70351

Pow

er P

(kW

)

Torq

ue M

d at

out

put

of u

nit

(Nm

)

Speed n1 at output of unit (rpm)


Performance chart

Driven tools, Tool carrier 2

Speed range 0-6000min-1

KL9652.40021

Pow

er P

(kW

)

Torq

ue M

d at

out

put

of u

nit

(Nm

)

Speed n1 at output of unit (rpm)


Tool holder fix

Shank VDI 25

For more information see http://infoshop.index-werke.de/ 3-2

W1200039

Bar stop, liveShank VDI 25Fixation noneMounting D25Cooling –reversable 180° yesX / Y / Z 70 (2.76) / – / 30 (1.18) mm ('')

Matching modulesBar stop W9990159Bar stop W9990160


W9990159

Bar stop, liveShank –Fixation –Mounting D58Cooling –X / Y / Z – / – / 30 (1.18) mm ('')

Matching base holderBar stop W1100008Bar stop W1200039Bar stop W1400035Bar stop W1300052Bar stop W1300054Bar stop W1200040


W9990160

Bar stop, liveShank –Fixation –Mounting D85Cooling –X / Y / Z – / – / 30 (1.18) mm ('')

Matching base holderBar stop W1100008Bar stop W1200039Bar stop W1400035Bar stop W1300052Bar stop W1300054Bar stop W1200040


W1230000

Compensation holderShank VDI 25Fixation Vee barMounting VDI 20Cooling external and internal, pmax 20 barreversable 180° yesX / Y / Z 70 (2.76) / – / 2 (0.8) mm ('')

Matching accessoriesNozzle* 474550.0101Cheese-head screw* 410243.0406

* This article is included


W1230035

Compensation holderShank VDI 25Fixation Vee barMounting VDI 20Cooling external and internal, pmax 40 barreversable 180° noX / Y / Z 60 (2.36) / – / 2 (0.8) mm ('')

Matching accessoriesNozzle* 474550.0101



W1230027

Compensation holderShank VDI 25Fixation Vee barMounting VDI 25Cooling internal, pmax 80 barreversable 180° yesX / Y / Z 70 (2.76) / – / 2 (0.8) mm ('')


W1230003

Compensation holderShank VDI 25Fixation Vee barMounting VDI 30Cooling internal, pmax 80 barreversable 180° noX / Y / Z 60 (2.36) / – / 3 (0.12) mm ('')


W1230026

Compensation holderShank VDI 25Fixation Vee barMounting VDI 30Cooling internal, pmax 80 barreversable 180° yesX / Y / Z 70 (2.76) / – / -5 (-0.2) mm ('')


W1230025

Compensation holderShank VDI 25Fixation Vee barMounting D1''Cooling external, pmax 80 barreversable 180° yesX / Y / Z 60 (2.36) / – / 15 (0.59) mm ('')

Matching accessoriesScrew cap* 471672.08Tube* W63451.1004



W1200042

Drilling tool holder, Specially for the marking tool WriteStarShank VDI 25Fixation noneMounting D12Cooling –reversable 180° noX / Y / Z 68 (2.68) / – / – mm ('')

Matching cutting toolsMarking tool W9990300

Other documentsProduct note W9800004en


W1230036

Drilling tool holderShank VDI 25Fixation Vee barMounting ER 16Cooling external, pmax 20 barreversable 180° noX / Y / Z 60 (2.36) / – / – mm ('')

Matching accessoriesClamping collet 901930.1---Clamping collet W99903--tapping tool collet 3230--tapping tool collet WZ9990.9506FCollet chuck W999066-Clamping nut* 901939.01Clamping bar W61100.0004Setting gauge W67101.0050Stop bar W67221.4106Cheese-head screw 410260.0616Spanner 490219.0161



W1230054

Drilling tool holderShank VDI 25Fixation Vee barMounting ER 25Cooling external and internal, pmax 80 barreversable 180° yesX / Y / Z 60 (2.36) / – / 31 (1.22) mm ('')

Matching accessoriesClamping collet 901930.3---tapping tool collet 3224--tapping tool collet WZ9990.9507FCollet chuck W999067-Clamping collet, sealed W999085-Clamping nut* 901939.0251Spanner 490219.0251




W1230056


Matching accessoriesClamping collet 901930.3---tapping tool collet 3224--tapping tool collet WZ9990.9507FCollet chuck W999067-Clamping collet, sealed W999085-Clamping nut* 901939.0251Coolant nozzle* W00019.0153Tube* W67500.3206Spanner 490219.0251




W1230055

Drilling tool holderShank VDI 25Fixation Vee barMounting ER 32Cooling external and internal, pmax 80 barreversable 180° yesX / Y / Z 60 (2.36) / – / 52 (25) mm ('')

Matching accessoriesClamping collet 901930.6---tapping tool collet 3242--tapping tool collet WZ9990.9509FCollet chuck W999068-Clamping nut* 901939.0321Spanner 490219.0321




W1230007

Drilling tool holder, vertically adjustableShank VDI 25Fixation Vee barMounting DIN 1835 B/E D16Cooling internal, pmax 80 barreversable 180° noX / Y / Z 70 (2.76) / – / 25 (0.98) mm ('')

Matching accessoriesBush W67511.04--


W1230046

Drilling tool holderShank VDI 25Fixation Vee barMounting DIN 1835 B/E D32Cooling external and internal, pmax 80 barreversable 180° yesX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')

Matching accessoriesBush W63220.02--Bush W63221.40--Nozzle* W67500.3208Bush* W67530.0824Hollow screw* W67530.0818Nozzle W00019.0216




W1230006


Matching accessoriesClamping collet 901930.4---Clamping nut* 901939.0401Nozzle* 474550.0121Cheese-head screw* 410243.0406Spanner 490219.0401



W1230032

Drilling tool holderShank VDI 25Fixation Vee barMounting D12Cooling external and internal, pmax 20 barreversable 180° noX / Y / Z 70 (2.76) / – / 30 (1.18) mm ('')

Matching accessoriesNozzle* 474550.0101Metal sheet* W67222.4108Cheese-head screw* 410243.0406



W1210001

Drilling tool holder, vertically adjustableShank VDI 25Fixation Setting gaugeMounting D16Cooling internal, pmax 80 barreversable 180° noX / Y / Z 60 (2.36) / ±1.5 (±06) / 30 (1.18) mm ('')


W1200000

Turning tool holder, Form C1/C4Shank VDI 25Fixation noneMounting square 16x16Cooling external, pmax 20 barreversable 180° yesX / Y / Z 55 (2.17) / – / 19 (0.75) mm ('')




W1200003





W1200001


Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* 474550.0121Cheese-head screw* 410243.0406



W1200004





W1200025

Turning tool holder, doubleShank VDI 25Fixation noneMounting square 20x20Cooling external, pmax 20 barreversable 180° noX / Y / Z 55 (2.17) / – / 17 (0.67) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Countersunk screw* 410360.0410Nozzle W00019.0216



W1200021

Turning tool holder, Form C2/C3Shank VDI 25Fixation noneMounting square 3/4x3/4''Cooling internal, pmax 20 barreversable 180° yesX / Y / Z 55 (2.17) / – / 19 (0.75) mm ('')




W1200022

Turning tool holder, Form C1/C4Shank VDI 25Fixation noneMounting square 3/4x3/4''Cooling internal, pmax 20 barreversable 180° yesX / Y / Z 55 (2.17) / – / 15 (0.59) mm ('')




W1220007

Turning tool holderShank VDI 25Fixation Clamping and stop barMounting square 20x20Cooling external, pmax 80 barreversable 180° yesX / Y / Z 40 (1.57) / – / 30 (1.18) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Bush* W67530.0824Hollow screw* W67530.0818Nozzle W00019.0216



W1230016

Turning tool holderShank VDI 25Fixation Vee barMounting square 20x20Cooling external, pmax 40 barreversable 180° noX / Y / Z 18.5 (0.73) / – / 30 (1.18) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Countersunk screw* 410360.0410



W1230021

Turning tool holderShank VDI 25Fixation Vee barMounting square 20x20Cooling external, pmax 40 barreversable 180° noX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Countersunk screw* 410360.0410Gib W67221.4104Stop bar W67221.4106



W1230029

Turning tool holderShank VDI 25Fixation Vee barMounting square 20x20Cooling external, pmax 80 barreversable 180° yesX / Y / Z 18.5 (0.73) / – / 30 (1.18) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Countersunk screw* 410360.0510Nozzle W00019.0216



W1230031

Turning tool holderShank VDI 25Fixation Vee barMounting square 20x20Cooling external, pmax 80 barreversable 180° yesX / Y / Z 60 (2.36) / – / 30 (1.18) mm ('')

Matching accessoriesAngle W63300.0010Angle W63300.0020Nozzle* W67500.3208Bush* W67530.0824Hollow screw* W67530.0818Nozzle W00019.0216



W1230020

Basic holder, vertically adjustableShank VDI 25Fixation Vee barMounting –Cooling external and internal, pmax 20 barreversable 180° yesX / Y / Z 35 (1.38) / – / 5 (0.2) mm ('')

Matching modulesGrooving tool holding block W9990038Grooving tool holding block W9990039Grooving tool holding block W9990064Grooving tool holding block W9990066Grooving tool holding block W9990067Grooving tool holding block W9990068Grooving tool holding block W9990069Grooving tool holding block W9990070Grooving tool holding block W9990071Grooving tool holding block W9990072Grooving tool holding block W9990073Grooving tool holding block W9990074Grooving tool holding block W9990075Grooving tool holding block W9990076Knurling tool holder W9990154

Matching accessoriesTube* W67311.0810Countersunk screw* 410360.0512



W9990038

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting Trapezoid 32x5Cooling –, pmax 20 barX / Y / Z 60 (2.36) / – / 32 (1.26) mm ('')

Matching base holderBasic holder W1250022Basic holder W1230020


W9990039




W9990064

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting square 16x16Cooling –X / Y / Z 40 (1.57) / – / 40 (1.57) mm ('')

Matching base holderBasic holder W1230020Basic holder W1250022Basic holder W8900013Basic holder W1350009Basic holder W1330004


W9990066

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting Trapezoid 26x5Cooling –X / Y / Z 47.5 (1.87) / – / 32 (1.26) mm ('')



W9990067




W9990068

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting Trapezoid 26x5Cooling –X / Y / Z 47.5 (1.87) / – / 28.5 (1.12) mm ('')



W9990069




W9990070




W9990071




W9990072




W9990073


Matching base holderBasic holder W8900013Basic holder W1230020Basic holder W1250022


W9990074

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting Trapezoid 16x3Cooling –X / Y / Z 20 (0.79) / – / 25 (0.98) mm ('')



W9990075




W9990076




W9990154

Knurling tool holderShank –Fixation noneMounting D6Cooling –X / Y / Z 38 (1.5) / – / 20 (0.79) mm ('')

Matching base holderBasic holder W1330004Basic holder W8900013Basic holder W1230020Basic holder W1250022

Matching cutting toolsKnurl 22191-.21--


W1230004

Basic holderShank VDI 25Fixation Vee barMounting –Cooling external and internal, pmax 20 barreversable 180° yesX / Y / Z 70 (2.76) / – / -5 (-0.2) mm ('')

Matching modulesDrill holding block W9990085Drill holding block W9990086

Matching accessoriesNozzle* 474550.0101Washer* 419010.04Cheese-head screw* 410243.0406



W9990085

Drill holding blockShank –Fixation –Mounting ER 25Cooling internal, pmax 20 barX / Y / Z 42.5 (1.67) / – / – mm ('')





W9990086

Drill holding blockShank –Fixation –Mounting D20Cooling external, pmax 20 barX / Y / Z 40 (1.57) / – / – mm ('')


Matching accessoriesBush W62220.01--Nozzle* 474550.0101



W1200008

Scroll holderShank VDI 25Fixation noneMounting –Cooling internal, pmax 20 barreversable 180° yesX / Y / Z 65 (2.56) / – / 40.5 (1.59) mm ('')

Matching accessoriesEmbossing roller* W63380.0030Embossing roller W63380.0060

Coolant required for function



W1200036

Calibrating toolShank VDI 25Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 110 (4.33) / – / – mm ('')


W1200009

Blanking plugShank VDI 25Fixation –Mounting –Cooling –reversable 180° noX / Y / Z 10 (0.39) / – / – mm ('')


W1200026

Coolant nozzleShank VDI 25Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 16 (0.63) / – / – mm ('')

Matching accessoriesNozzle* W67500.3208Countersunk screw* 410360.0408Nozzle W00019.0216




Tool holder live

Shank VDI 25


W1235047

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 11Cooling external, pmax 20 barSpeed ratio 1:3 (0.333)Direction same as drive directionreversable 180° yesX / Y / Z 75 (2.95) / – / 15 (0.59) mm ('')

Matching accessoriesClamping collet 901930.0---tapping tool collet 3239--tapping tool collet 900288Collet chuck W999064-Clamping nut* 901939.5111Nozzle* 474550.0121Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Cheese-head screw 410260.0616Spanner 490219.3111



W1235049

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 11Cooling external, pmax 20 barSpeed ratio 1:1.33 (0.75)Direction opposite to drive directionreversable 180° yesX / Y / Z 70 (2.76) / – / 17.5 (0.69) mm ('')

Matching accessoriesClamping collet 901930.0---tapping tool collet 3239--tapping tool collet 900288Collet chuck W999064-Clamping nut* 322438Nozzle* W67500.3208Bush* W67530.0824Hollow screw* W67530.0818Nozzle W00019.0216Spanner 490219.0111



W1205022

Drilling unitShank VDI 25Fixation noneDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 54 (2.13) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Tube* W67501.0020Countersunk screw* 410360.0412Spanner 490219.3201



W1205025

Milling unitShank VDI 25Fixation noneDrive Beveled wheel (ABC)Mounting D16Cooling external, pmax 40 barSpeed ratio 4.5:1 (4.5)Direction same as drive directionreversable 180° noX / Y / Z 82 (3.23) / – / 0 mm ('')

Matching accessoriesBush W67511.04--Tube* W67501.0020Countersunk screw* 410360.0410



W1225010

Milling unitShank VDI 25Fixation Clamping and stop barDrive Beveled wheel (ABC)Mounting Milling tool mounting D22Cooling external, pmax 20 barSpeed ratio 2:1 (2)Direction opposite to drive directionreversable 180° noX / Y / Z 74 (2.91) / – / 45 (1.77) mm ('')

Matching accessoriesRing 251390.----Ring 251391.----Screw* 250122.1028Nozzle* 474550.0121Cheese-head screw* 410243.0408mill arbor wrench 203020.1220Hook wrench 490340.0500



W1205018

Tapping unit, extendableShank VDI 25Fixation noneDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 60 (2.36) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.2---Collet chuck W999066-Clamping nut* 901939.5201Driver W67451.0075Tube* W67501.0020Countersunk screw* 410360.0410Spanner 490219.3201



W1235053

Circular saw unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)Direction same as drive directionreversable 180° noX / Y / Z 68 (2.68) / – / 0 mm ('')

Matching cutting toolsSaw blade 223010.63--

Matching accessoriesRing 251390.----Ring 251391.----Tube* W67501.0020Countersunk screw* 410360.0410Bush W92853.2050Bush W92853.2060Bush W61851.0050Bush* WK7850.22Gib W61851.0004



W1235045

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° yesX / Y / Z 70 (2.76) / – / 53 (29) mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Nozzle* 474550.0101Cheese-head screw* 410243.0406Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Gib W67212.2504Cheese-head screw 410260.0616Spanner 490219.3201



W1235046

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 60 (2.36) / – / 53 (29) mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Nozzle* 474550.0101Cheese-head screw* 410243.0406Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Gib W67212.2504Cheese-head screw 410260.0616Spanner 490219.3201



W1235058

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 20Cooling external, internal optional, pmax 20 bar

Speed ratio 2:1 (2)Direction same as drive directionreversable 180° yesX / Y / Z 70 (2.76) / – / 53 (29) mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping collet, sealed W999084-Clamping nut* 901939.5201Adapter for Internal cooling W67501.2050Nozzle* 474550.0101Cheese-head screw* 410243.0406Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Gib W67212.2504Cheese-head screw 410260.0616Spanner 490219.3201



W1235042

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting DIN 1835 E D16Cooling internal, pmax 40 barSpeed ratio 1:2 (0.5)Direction same as drive directionreversable 180° yesX / Y / Z 60 (2.36) / – / 79 (3.11) mm ('')

Matching accessoriesBush W67511.04--Gib W67503.2004

No dry run.


W1235044

Milling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting D10Cooling external, pmax 40 barSpeed ratio 2.09:1 (2.09)Direction opposite to drive directionreversable 180° yesX / Y / Z 55 (2.17) / – / 55 (2.17) mm ('')

Matching modulesMilling cutter holding block W9990040Milling cutter holding block W9990041Milling cutter holding block W9990042Milling cutter holding block W9990043Milling cutter holding block W9990044

Matching accessoriesTube* W95060.4012Countersunk screw* 410360.0512Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Cheese-head screw 410260.0616



W1235052

Milling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2.09:1 (2.09)Direction opposite to drive directionreversable 180° yesX / Y / Z 55 (2.17) / – / 47.5 (1.87) mm ('')

Matching accessoriesRing 251390.----Ring 251391.----Tube* W95060.4012Countersunk screw* 410360.0512Spindle W68831.9030Setting gauge W67101.0050Clamping bar W61100.0004Stop bar W67221.4106Cheese-head screw 410260.0616Hook wrench 490340.0300



W1225008

Tapping unit, extendableShank VDI 25Fixation Clamping and stop barDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 2:1 (2)Direction opposite to drive directionreversable 180° noX / Y / Z 70 (2.76) / – / 78 (37) mm ('')

Matching accessoriesClamping collet 901930.2---Collet chuck W999066-Clamping nut* 901939.5201Driver W67451.00--Nozzle W00019.0216Nozzle* W67500.3208Tube* W67500.3206Spanner 490219.3201



W1235051

Broaching/ Slotting unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting D20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 60 (2.36) / – / 75 (2.95) mm ('')

Matching cutting toolsMandrel W37606.----

Matching accessoriesBush W37610.2012Tube* WK5102.10Countersunk screw* 410360.0512



W1235050

Drilling unitShank VDI 25Fixation Vee barDrive Beveled wheel (ABC)Mounting ER 11Cooling external, pmax 40 barSpeed ratio 1:1.7 (0.588)Direction opposite to drive directionreversable 180° noX / Y / Z 44 (1.73) / – / 37 (1.46) mm ('')

Matching accessoriesClamping collet 901930.0---tapping tool collet 3239--tapping tool collet 900288Collet chuck W999064-Clamping nut* 901939.5111Tube* W67500.3206Spanner 490219.3111Spanner W61511.5072



W9990040

Milling cutter holding blockShank –Fixation –Mounting Milling tool mounting D13Cooling –X / Y / Z – / – / – mm ('')

Matching base holderMilling attachment G728419-02Milling cutter holder W2400027Milling unit W1205010Milling unit W1205042Milling unit W1235039Milling unit W1235044Milling unit W1255015Milling unit W1255134Milling unit W1305002Milling unit W1305007Milling unit W1305010Milling unit W1305025Milling unit W1305034Milling unit W1325000Milling unit W1335004Holder W1335012Milling unit W1345005Milling unit W1345012Milling unit W1345013Milling unit W1345082Circular saw unit W1345109Milling unit W1355001Milling unit W1405003Milling unit W1405013Milling unit W1435005Circular saw unit W1445005Milling unit W1445006Milling unit W1455011Milling unit W1155007

Matching accessoriesRing 251390.----Ring 251391.----Screw 250122.0617mill arbor wrench 203020.1130


W9990041


Matching base holderMilling unit W1345048Milling cutter holder W2400027Milling unit W1205010Milling unit W1205042Milling unit W1235039Milling unit W1235044Milling unit W1255015Milling unit W1255134Milling unit W1305002Milling unit W1305007Milling unit W1305010Milling unit W1305025Milling unit W1305034Milling unit W1325000Milling unit W1335004Holder W1335012Milling unit W1345005Milling unit W1345012Milling unit W1345013Milling unit W1345082Circular saw unit W1345109Milling unit W1355001Milling unit W1405003Milling unit W1405013Milling unit W1435005Circular saw unit W1445005Milling unit W1445006Milling unit W1455011Milling attachment G728419-02Milling unit W1155007



W9990042





W9990043





W9990044


Matching base holderMilling attachment G728419-02Milling cutter holder W2400027Milling unit W1205010Milling unit W1205042Milling unit W1235039Milling unit W1235044Milling unit W1255015Milling unit W1255134Milling unit W1305002Milling unit W1305007Milling unit W1305010Milling unit W1305025Milling unit W1305034Milling unit W1325000Milling unit W1335004Holder W1335012Milling unit W1345005Milling unit W1345012Milling unit W1345013Milling unit W1345082Circular saw unit W1345109Milling unit W1355001Milling unit W1405003Milling unit W1405013Milling unit W1435005Circular saw unit W1445005Milling unit W1445006Milling unit W1455011Milling unit W1155007



Tool holder to spring-loaded tap holder

Shank VDI 20


W1100017

Bar stop, adjustable, liveShank VDI 20Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 49.5 - 71.5 (1.95 - 2.81) / – / – mm ('')


W1100006

Drilling tool holderShank VDI 20Fixation noneMounting ER 16Cooling internal, pmax 20 barreversable 180° noX / Y / Z 42.5 (1.67) / – / – mm ('')

Matching accessoriesClamping collet 901930.1---Clamping collet W99903--tapping tool collet 3230--tapping tool collet WZ9990.9506FCollet chuck W999065-Clamping collet, sealed W999083-Clamping nut* 901939.01Spanner 490219.0161



W1100007

Drilling tool holder, Form E4Shank VDI 20Fixation noneMounting ER 25Cooling internal, pmax 80 barreversable 180° noX / Y / Z 51 (21) / – / – mm ('')




W1100010

Drilling tool holder, Form E4Shank VDI 20Fixation noneMounting ER 40Cooling internal, pmax 20 barreversable 180° noX / Y / Z 66.5 (2.62) / – / – mm ('')

Matching accessoriesClamping collet 901930.4---Clamping nut* 901939.0401Spanner 490219.0401



W1100004

Drilling tool holder, Form E1Shank VDI 20Fixation noneMounting DIN 1835 B/E D20Cooling internal, pmax 20 barreversable 180° noX / Y / Z 48 (1.89) / – / – mm ('')



W1100005

Drilling tool holder, Form E1Shank VDI 20Fixation noneMounting DIN 1835 B/E D25Cooling internal, pmax 80 barreversable 180° noX / Y / Z 56.5 (2.22) / – / – mm ('')



W1100018

Drilling tool holder, Form E2Shank VDI 20Fixation noneMounting D10Cooling external, pmax 20 barreversable 180° noX / Y / Z 50 (1.97) / – / – mm ('')


W1100019




W1100001

Drilling tool holderShank VDI 20Fixation noneMounting D15Cooling external, pmax 20 barreversable 180° noX / Y / Z 26 (12) / – / – mm ('')

Matching accessoriesBush 993115.----Nozzle* 474550.0121



W1100020




W1100009

Drilling tool holderShank VDI 20Fixation noneMounting D25Cooling external, pmax 20 barreversable 180° noX / Y / Z 43 (1.69) / – / – mm ('')

Matching accessoriesBush 993125.----Nozzle* 474550.0121



W1100002

Basic holder, vertically adjustableShank VDI 20Fixation noneMounting –Cooling internal, pmax 20 barreversable 180° noX / Y / Z 14 (0.55) / – / – mm ('')



W9990085

Drill holding blockShank –Fixation –Mounting ER 25Cooling internal, pmax 20 barX / Y / Z 42.5 (1.67) / – / – mm ('')





W9990086

Drill holding blockShank –Fixation –Mounting D20Cooling external, pmax 20 barX / Y / Z 40 (1.57) / – / – mm ('')




W1100014

Center holder, elastic, live, Center replacebleShank VDI 20Fixation noneMounting MK0Cooling –reversable 180° noX / Y / Z 66 (2.6) / – / – mm ('')

Matching accessoriesCenter* W13622.16

Center replaceble!



W1100013

Center holder, elastic, liveShank VDI 20Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 65 (2.56) / – / – mm ('')


W1100011

Tapping tool holder, over-runningShank VDI 20Fixation noneMounting D12Cooling external, pmax 20 barreversable 180° noX / Y / Z 56 (2.2) / – / – mm ('')

Matching accessoriesBush 993112.----

Only for right-handed threads


W1100003

Tapping tool holderShank VDI 20Fixation noneMounting D18Cooling external, pmax 20 barreversable 180° noX / Y / Z 50.5 (1.99) / – / – mm ('')



W1100012

Reaming tool holder, adjustableShank VDI 20Fixation noneMounting D12Cooling external, pmax 20 barreversable 180° noX / Y / Z 52 (25) / – / – mm ('')



W1100016

Broaching/ Slotting tool holder, rotating, liveShank VDI 20Fixation noneMounting D12Cooling external, pmax 20 barreversable 180° noX / Y / Z 66 (2.6) / – / – mm ('')


Matching accessoriesTube* W62211.2110Countersunk screw* 410360.0512



W1100015


Matching accessoriesTube* W62211.2110




Shank VDI 25


W1200006

Drilling tool holder, Form E4Shank VDI 25Fixation noneMounting ER 25Cooling internal, pmax 40 barreversable 180° noX / Y / Z 57 (2.24) / – / – mm ('')




W1200017





W1200011



W1200012



W1200013


Matching accessoriesGrub screw W00013.0039


W1200014




W1200020

Drilling tool holder, Form E2Shank VDI 25Fixation noneMounting D8Cooling external and internal, pmax 80 barreversable 180° noX / Y / Z 50 (1.97) / – / – mm ('')


W1200015



W1200016



W1200042





W1200019




W1200033




W1200018




W9990095

Compensation bushingShank VDI 25Fixation noneMounting D3/4''Cooling –Direction same as drive directionreversable 180° noX / Y / Z 6 (0.24) / – / – mm ('')


W1200007

Tapping tool holder, extendableShank VDI 25Fixation noneMounting DIN 1835 B/E D18Cooling external, pmax 20 barreversable 180° noX / Y / Z 50 (1.97) / – / – mm ('')

Matching accessoriesBush 993118.----Tube* W62211.2110Countersunk screw* 410360.0512



W1200028

Reaming tool holderShank VDI 25Fixation noneMounting ER 16Cooling external, pmax 20 barreversable 180° noX / Y / Z 63 (2.48) / – / – mm ('')

Matching accessoriesClamping collet 901930.1---Clamping collet W99903--Collet chuck W999065-Clamping nut* 901939.01Tube* W63211.5112Countersunk screw* 410360.0512Spanner 490219.0161



W1200030






W1200027


Drawing scale changed,template inapplicable!




Shank VDI 30


W1300037

Bar stop, adjustable, liveShank VDI 30Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 60 - 97 (2.36 - 3.82) / – / – mm ('')


W1300038

Bar stop, adjustable, liveShank VDI 30Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 60 - 97 (2.36 - 3.82) / – / – mm ('')


W9990096

Compensation bushingShank VDI 30Fixation noneMounting D3/4''Cooling –reversable 180° noX / Y / Z 6 (0.24) / – / – mm ('')


W9990094

Compensation bushingShank VDI 30Fixation noneMounting D1''Cooling –reversable 180° noX / Y / Z 6 (0.24) / – / – mm ('')


W1300023

Compensation holderShank VDI 30Fixation noneMounting D1''Cooling internal, pmax 20 barreversable 180° noX / Y / Z 60 (2.36) / – / – mm ('')

Matching accessoriesBush W35200.1905


W1300025





W1300066





W1300026


Matching accessoriesClamping collet 901930.4---Clamping nut* 901939.0401Spanner 490219.0401



W1300057

Drilling tool holder, Form E1Shank VDI 30Fixation noneMounting DIN 1835 E D20Cooling internal, pmax 80 barreversable 180° noX / Y / Z 67 (2.64) / – / – mm ('')


W1300058

Drilling tool holder, Form E1Shank VDI 30Fixation noneMounting DIN 1835 E D25Cooling internal, pmax 80 barreversable 180° noX / Y / Z 71 (2.8) / – / – mm ('')



W1300014



W1300015



W1300016



W1300067





W1300017




W1300018




W1300019




W1300053

Drilling tool holderShank VDI 30Fixation noneMounting D25Cooling external and internal, pmax 40 barreversable 180° noX / Y / Z 45 (1.77) / – / – mm ('')

Matching accessoriesBush 993125.----Nozzle* 474550.0121Cheese-head screw* 410243.0406



W1300013


Matching accessoriesBush W63220.02--Nozzle* 474550.0121



W1300022

Drilling tool holderShank VDI 30Fixation noneMounting D32Cooling internal, pmax 80 barreversable 180° noX / Y / Z 73 (2.87) / – / – mm ('')

Matching accessoriesBush W63221.4020Bush W63221.4025


W1300027

Drilling tool holderShank VDI 30Fixation noneMounting MK1Cooling external, pmax 20 barreversable 180° noX / Y / Z 30 (1.18) / – / – mm ('')

Matching accessoriesNozzle* 474550.0121



W1300028

Drilling tool holderShank VDI 30Fixation noneMounting MK2Cooling external, pmax 20 barreversable 180° noX / Y / Z 27 (16) / – / – mm ('')


W1300029

Drilling tool holderShank VDI 30Fixation noneMounting MK3Cooling external, pmax 20 barreversable 180° noX / Y / Z 45 (1.77) / – / – mm ('')


W1300012

Basic holder, vertically adjustableShank VDI 30Fixation noneMounting –Cooling external, pmax 20 barreversable 180° noX / Y / Z 14 (0.55) / – / – mm ('')


Matching accessoriesTube W63210.2006


W9990092

Drill holding blockShank –Fixation –Mounting ER 25Cooling –, pmax 40 barX / Y / Z 30 (1.18) / – / – mm ('')





W9990093

Drill holding blockShank –Fixation –Mounting D32Cooling –, pmax 40 barX / Y / Z 57 (2.24) / – / – mm ('')




W1300004

Center holder, liveShank VDI 30Fixation noneMounting D15.4/Cone 1:7.5Cooling –reversable 180° noX / Y / Z 69.5 (2.74) / – / – mm ('')

Matching accessoriesCenter W9636-.21--

Center replaceble!


W1300005

Center holder, elastic, liveShank VDI 30Fixation noneMounting D15.4/Cone 1:7.5Cooling –reversable 180° noX / Y / Z 68.5 (2.7) / – / – mm ('')

Matching accessoriesCenter W9636-.21--

Range of spring 2.7 mmYellow ring 0 -2500 NGreen ring 2500 - 5000 NRed ring 5000 - 8500 N


W1300030

Tapping tool holder, extendableShank VDI 30Fixation noneMounting D25Cooling external, pmax 20 barreversable 180° noX / Y / Z 73 (2.87) / – / – mm ('')




W1300031

Reaming tool holder, adjustableShank VDI 30Fixation noneMounting ER 25Cooling external, pmax 20 barreversable 180° noX / Y / Z 73.5 (2.89) / – / – mm ('')

Matching accessoriesClamping collet 901930.3---Collet chuck W999067-Clamping nut* 901939.0251Tube* W63211.5112Countersunk screw* 410360.0512Spanner 490219.0251



W1300032

Reaming tool holder, adjustableShank VDI 30Fixation noneMounting D18Cooling external, pmax 20 barreversable 180° noX / Y / Z 59 (2.32) / – / – mm ('')




W1300065

Reaming tool holder, self-centeringShank VDI 30Fixation noneMounting D20Cooling internal, pmax 40 barreversable 180° noX / Y / Z 93 (3.66) / – / – mm ('')



W1300034



Matching accessoriesNozzle* 474550.0121Tube* W63501.2622Cheese-head screw* 410243.0406



Tool holder fix

Vee mounting


W8900003

Bar stop, adjustableShank Dovetail (ABC)Fixation noneMounting –Cooling –reversable 180° noX / Y / Z 85 (3.35) / – / -17 (-0.67) mm ('')


W8900014

Bar stop, adjustable, liveShank Dovetail (ABC)Fixation noneMounting –Cooling –reversable 180° yesX / Y / Z 85 (3.35) / – / -65 (-2.56) mm ('')


W8900001

Turning tool holder, doubleShank Dovetail (ABC)Fixation noneMounting square 20x20Cooling external, pmax 20 barreversable 180° noX / Y / Z 65 (2.56) / – / 0 mm ('')




W8900002

Turning tool holderShank Dovetail (ABC)Fixation noneMounting square 20x20Cooling external, pmax 20 barreversable 180° noX / Y / Z 85 (3.35) / – / 0 mm ('')




W8900006

Basic holder, Contour plunging tool holderShank Dovetail (ABC)Fixation noneMounting –Cooling external, pmax 40 barreversable 180° noX / Y / Z 45.5 (1.79) / – / 9 (0.35) mm ('')

Matching modulesGrooving tool holding block W9990244


W9990244

Grooving tool holding block, adjustableShank –Fixation –Mounting –Cooling –reversable 180° yesX / Y / Z 40 (1.57) / – / – mm ('')



W8900007

Basic holder, angle-adjustableShank Dovetail (ABC)Fixation noneMounting –Cooling external, pmax 40 barreversable 180° noX / Y / Z 42 (1.65) / – / 0 mm ('')

Matching modulesGrooving tool holding block W9990055Grooving tool holding block W9990065

Matching accessoriesBall* 420800.1000Tube* W61012.0110



W9990055

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting –Cooling external, pmax 20 barX / Y / Z 30 (1.18) / – / – mm ('')

Matching base holderBasic holder W1150032Basic holder W1200023Grooving tool holding block W9990357Basic holder W8900007Basic holder W1250003

Matching accessoriesShim W31400.46


W9990065

Grooving tool holding block, vertically adjustableShank –Fixation –Mounting –Cooling external, pmax 20 barX / Y / Z 38 (1.5) / – / – mm ('')

Matching base holderBasic holder W1150032Basic holder W1200023Basic holder W1250003Basic holder W8900007Grooving tool holding block W9990357

Matching accessoriesShim W31400.46


W8900013

Basic holder, adjustableShank Dovetail (ABC)Fixation noneMounting –Cooling external, pmax 40 barreversable 180° yesX / Y / Z 52 (25) / – / 10 (0.39) mm ('')

Matching modulesGrooving tool holding block W9990245Grooving tool holding block W9990246Grooving tool holding block W9990064Grooving tool holding block W9990066Grooving tool holding block W9990067Grooving tool holding block W9990068Grooving tool holding block W9990069Grooving tool holding block W9990072Grooving tool holding block W9990073Grooving tool holding block W9990074Grooving tool holding block W9990075Grooving tool holding block W9990076Knurling tool holder W9990154

Matching accessoriesNozzle* 474550.0121Cheese-head screw* 410232.0406Tube* W61003.0032



W9990245

Grooving tool holding block, adjustableShank –Fixation –Mounting square 20x20Cooling –reversable 180° yesX / Y / Z 37 (1.46) / – / 28 (1.10) mm ('')

Matching base holderBasic holder W8900013


W9990246

Grooving tool holding block, adjustableShank –Fixation –Mounting square 20x20Cooling –reversable 180° yesX / Y / Z 45 (1.77) / – / 28 (1.10) mm ('')



W9990064




W9990066




W9990067




W9990068




W9990069




W9990072




W9990073




W9990074




W9990075




W9990076




W9990154

Knurling tool holderShank –Fixation noneMounting D6Cooling –X / Y / Z 38 (1.5) / – / 20 (0.79) mm ('')

Matching base holderBasic holder W1330004Basic holder W8900013Basic holder W1230020Basic holder W1250022

Matching cutting toolsKnurl 22191-.21--


W8900005

Basic holder, vertically adjustableShank Dovetail (ABC)Fixation noneMounting –Cooling external and internal, pmax 20 barreversable 180° noX / Y / Z 62 (2.44) / – / -30 (-1.18) mm ('')

Matching modulesDrill holding block W9990242Drill holding block W9990045Drill holding block W9990243




W9990242

Drill holding block, horizontally adjustableShank –Fixation –Mounting D1''Cooling –, pmax 20 barreversable 180° noX / Y / Z 23.55 (0.93) / – / 50 (1.97) mm ('')


Matching modulesDrilling tool holder W6290001


W9990045

Drill holding blockShank –Fixation –Mounting D25Cooling –X / Y / Z 23.55 (0.93) / – / – mm ('')




W9990243

Drill holding blockShank –Fixation noneMounting D25Cooling external, pmax 20 barreversable 180° noX / Y / Z 33.55 (1.32) / – / 50 (1.97) mm ('')




W8900009

Center holder, elasticShank Dovetail (ABC)Fixation –Mounting MK1Cooling –reversable 180° noX / Y / Z 85 (3.35) / – / -71 (-2.8) mm ('')

Matching accessoriesCenter W33621.16


W8900010

Scroll holderShank Dovetail (ABC)Fixation –Mounting –Cooling –, pmax 40 barreversable 180° noX / Y / Z 90 mm (3.54 '') / – / – mm ('')

Matching accessoriesEmbossing roller W63380.0030Embossing roller W63380.0060

Coolant required for function


W8900012

Calibrating toolShank Dovetail (ABC)Fixation noneMounting D40Cooling –reversable 180° yesX / Y / Z 110 (4.33) / – / 0 mm ('')


W8900000

Cover plate, SteelShank Dovetail (ABC)Fixation noneMounting –Cooling –X / Y / Z 12 (0.47) / – / – mm ('')


Tool holder live

Vee mounting


W8905002

Drilling unitShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting ER 11Cooling external, pmax 20 barSpeed ratio 1:1.33 (0.75)Direction opposite to drive directionreversable 180° noX / Y / Z 87 (3.43) / – / 1.5 (06) mm ('')

Matching accessoriesClamping collet 901930.0---tapping tool collet 3239--tapping tool collet 900288Collet chuck W999064-Clamping nut* 322438Nozzle* 474550.0101Tube* W63501.2622Cheese-head screw* 410232.0406Spanner 490219.0111



W8905004

Drilling unit, vertically adjustableShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting ER 16Cooling external, pmax 20 barSpeed ratio 1:1.93 (0.518)Direction opposite to drive directionreversable 180° noX / Y / Z 105 (4.13) / – / 37.5 (1.48) mm ('')

Matching accessoriesClamping collet 901930.1---Clamping collet W99903--tapping tool collet 3230--tapping tool collet WZ9990.9506FCollet chuck W999065-Clamping nut* 901939.5161Nozzle* 474550.0101Tube* W67500.3206Spanner 490219.3161



W8905000

Drilling unitShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 64 (2.52) / – / -16.5 (-0.65) mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Nozzle* 474550.0101Tube* W63501.2622Cheese-head screw* 410232.0406Spanner 490219.3201



W8905001

Milling unitShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting DIN 1835 B/E D16Cooling external, pmax 40 barSpeed ratio 4.5:1 (4.5)Direction same as drive directionreversable 180° noX / Y / Z 96 (3.78) / – / -16.5 (-0.65) mm ('')

Matching accessoriesBush W67511.04--Tube* W67501.0020Cheese-head screw* 410232.0406



W8905005

Drilling unitShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting ER 20Cooling external, pmax 20 barSpeed ratio 1:1.13 (0.8857)Direction opposite to drive directionreversable 180° noX / Y / Z 85 (3.35) / – / 36.5 (1.44) mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Nozzle* 474550.0101Cheese-head screw* 410232.0506Spanner 490219.3201



W8905003

Drilling unit, angle-adjustableShank Dovetail (ABC)Fixation noneDrive Beveled wheel (ABC)Mounting ER 11Cooling external, pmax 40 barSpeed ratio 1:1.7 (0.588)Direction same as drive directionreversable 180° noX / Y / Z 62 (2.44) / – / 53.5 (2.11) mm ('')

Matching accessoriesClamping collet 901930.0---tapping tool collet 3239--tapping tool collet 900288Collet chuck W999064-Clamping nut* 901939.5111Gasket ring* 479103.0211Tube* W67500.3206Spanner 490219.3111Spanner W61511.5072




Tool holder fix

Shank VDI 25, Rear End Machining Unit


W1200006





W1200017





W1200011



W1200012



W1200013




W1200014




W1200020



W1200015



W1200016



W1200042





W1200019




W1200033




W1200018




W9990095

Compensation bushingShank VDI 25Fixation noneMounting D3/4''Cooling –Direction same as drive directionreversable 180° noX / Y / Z 6 (0.24) / – / – mm ('')


W1200007

Tapping tool holder, extendableShank VDI 25Fixation noneMounting DIN 1835 B/E D18Cooling external, pmax 20 barreversable 180° noX / Y / Z 50 (1.97) / – / – mm ('')




W1200028

Reaming tool holderShank VDI 25Fixation noneMounting ER 16Cooling external, pmax 20 barreversable 180° noX / Y / Z 63 (2.48) / – / – mm ('')

Matching accessoriesClamping collet 901930.3---tapping tool collet 3224--tapping tool collet WZ9990.9507FCollet chuck W999067-Sealing washer W99904--Clamping nut 901939.3251Spanner 490219.0251


W1200030






W1200027


Drawing scale changed,template inapplicable!



Tool holder live

Shank VDI 25, Rear End Machining Unit


W1205023

Drilling unitShank VDI 25Fixation noneDrive Spline shaft (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 54 (2.13) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.2---tapping tool collet 3234--Collet chuck W999066-Clamping nut* 901939.5201Tube* W67501.0020Countersunk screw* 410360.0412Spanner 490219.3201



W1205021

Tapping unit, extendableShank VDI 25Fixation noneDrive Spline shaft (ABC)Mounting ER 20Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° noX / Y / Z 60 (2.36) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.2---Collet chuck W999066-Clamping nut* 901939.5201Driver W67451.00--Tube* W67501.0020Countersunk screw* 410360.0410Spanner 490219.3201



W1235054

Circular saw unitShank VDI 25Fixation Vee barDrive Spline shaft (ABC)Mounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)Direction same as drive directionreversable 180° noX / Y / Z 68 (2.68) / – / 0 mm ('')

Matching cutting toolsSaw blade 223010.63--Saw blade 223011.80--

Matching accessoriesTube* W67501.0020Countersunk screw* 410360.0410Bush* WK7850.22Bush W92853.2050Bush W92853.2060Bush W61851.0050Gib W61851.0004



Tool holder fix

Shank 1“, Rear End Machining Unit


W6290001

Drilling tool holderShank 1''Fixation noneMounting ER 25Cooling –X / Y / Z 22 (0.87) / – / – mm ('')

Matching base holderDrill holding block W9990242




W6290020

Drilling tool holderShank 1''Fixation noneMounting ER 25Cooling internal, pmax 40 barreversable 180° yesX / Y / Z 50 (1.97) / – / 0 mm ('')




W6290019

Drilling tool holderShank 1''Fixation noneMounting DIN 1835 B/E D25Cooling internal, pmax 40 barreversable 180° yesX / Y / Z 56 (2.2) / – / 0 mm ('')



W6290018

Drilling tool holder, adjustableShank 1''Fixation noneMounting D18Cooling internal, pmax 20 barreversable 180° yesX / Y / Z 56 (2.2) / ±2 (±08) / ±2 (08) mm ('')

Matching accessoriesBush 993118.----Turning tool holder W9990241Locking plate W9990997


W6290000

Drilling tool holderShank 1''Fixation noneMounting D25Cooling –X / Y / Z 40 (1.57) / – / – mm ('')



W6290015

Drilling tool holderShank 1''Fixation noneMounting MK1Cooling –Direction same as drive directionreversable 180° yesX / Y / Z 16 (0.63) / – / – mm ('')


W6290016

Drilling tool holderShank 1''Fixation noneMounting MK2Cooling –Direction same as drive directionreversable 180° yesX / Y / Z 29 (1.14) / – / – mm ('')


W6290008

Center holder, elastic, liveShank 1''Fixation noneMounting D18Cooling –X / Y / Z 72.5 (2.85) / – / – mm ('')


W6290007

Center holder, elastic, liveShank 1''Fixation noneMounting MK1Cooling –X / Y / Z 72.5 (2.85) / – / – mm ('')

Matching accessoriesCenter W33621.16

Center replaceble!


W6290002

Tapping tool holder, extendableShank 1''Fixation noneMounting D25Cooling –X / Y / Z 52 (25) / – / – mm ('')



W6290003

Tapping tool holder, over-runningShank 1''Fixation noneMounting D25Cooling –X / Y / Z 56 (2.2) / – / – mm ('')



W6290005

Reaming tool holder, adjustableShank 1''Fixation noneMounting ER 25Cooling –X / Y / Z 55 (2.17) / – / – mm ('')

Matching accessoriesClamping collet 901930.3---Collet chuck W999067-Clamping collet, sealed W999085-Clamping nut* 901939.3251Spanner 490219.0251



W6290006

Reaming tool holder, adjustableShank 1''Fixation noneMounting D18Cooling –X / Y / Z 41 (1.61) / – / – mm ('')



W6290011

Broaching/ Slotting tool holder, rotating, liveShank 1''Fixation noneMounting D12Cooling –X / Y / Z 58 (2.28) / – / – mm ('')



W6290012

Broaching/ Slotting tool holder, rotating, liveShank 1''Fixation noneMounting D20Cooling –X / Y / Z 76 (2.99) / – / – mm ('')


Matching accessoriesBush W37610.2012


W6290010

Broaching/ Slotting tool holder, rotating, liveShank 1''Fixation noneMounting D30Cooling –X / Y / Z 78 - 88 (37 - 3.46) / – / – mm ('')

Matching cutting toolsDrawing AZ4091.00


W6290009

Broaching/ Slotting tool holderShank 1''Fixation noneMounting D50Cooling –X / Y / Z 80 - 90 (3.2 - 3.54) / – / – mm ('')


W6290017

Guide holderShank 1''Fixation noneMounting –Cooling –X / Y / Z 57 (2.24) / – / – mm ('')

Matching modulesRoller holding block W9990176Roller holding block W9990177



W9990176

Roller holding block, adjustableShank –Fixation –Mounting –Cooling –X / Y / Z – / – / – mm ('')

Matching base holderGuide holder W6290017

Matching cutting toolsSliding roller W33400.06


W9990177

Roller holding block, adjustableShank –Fixation –Mounting –Cooling –X / Y / Z – / – / – mm ('')

Matching base holderGuide holder W6290017

Matching cutting toolsSliding roller W33400.06


W6290004

Knurling tool holder, adjustableShank 1''Fixation noneMounting D6-36Cooling –X / Y / Z – / – / – mm ('')

Matching accessoriesBush 993125.----Spacer W33960.1812


Tool holder live

Shank 1“, Rear End Machining Unit


W6295001

Drilling unitShank 1''Fixation noneDrive Spline shaft (ABC)Mounting ER 25Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° yesX / Y / Z 68 (2.68) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.3---tapping tool collet 3224--tapping tool collet WZ9990.9507FCollet chuck W999067-Clamping nut* 901939.5251Tube* W63490.0022Countersunk screw* 410360.0512Spanner 490219.3251



W6295000

Tapping unit, extendableShank 1''Fixation noneDrive Spline shaft (ABC)Mounting ER 16Cooling external, pmax 40 barSpeed ratio 1:1 (1)Direction same as drive directionreversable 180° yesX / Y / Z 61 (2.4) / – / 0 mm ('')

Matching accessoriesClamping collet 901930.1---Clamping collet W99903--tapping tool collet WZ9990.9506FCollet chuck W999065-Clamping nut* 901939.5161Tube* WK5102.10Spanner 490219.3161

For right-and left-handedthreads



W6295002

Circular saw unitShank 1''Fixation noneDrive Spline shaft (ABC)Mounting Milling tool mounting D16Cooling external, pmax 40 barSpeed ratio 2,7:1 (2,7)Direction same as drive directionreversable 180° noX / Y / Z 75 (2.95) / ±12.5 (±0.49) / 0 mm ('')

Matching cutting toolsSaw blade 223010.63--Saw blade 223011.80--

Matching accessoriesRing 251390.----Ring 251391.----Clamping piece K84091.50Tube* WK7851.50Bush W61851.0050Bush* WK7850.22Bush W92853.2050Bush W92853.2060



Accessories

INDEX ABC


2

7,515,5

ø8ø17

ø40

IC Attachment

for internal cooling lubricant supply, 20 barno dry run

W67501.2050


ø50

ø8

13,5 8

IC Attachment

for internal cooling lubricant supply, 20 barno dry run

W67500.5044


10

2620°

8°

Steel Block

for form cutting tool

W31400.46


Setting gauge

W67101.0050

55 12

21


Turning tool holder

W9990241

ø18h6

94

74

12 14 1822


Locking plate

W9990997

ø20

25

23

46

64


Replacement Seals for Tool Shank

The color of the reordered O-ring must always be the same as the one already used on the tool shank.

AZ4005.03

O-ring O-ring color Part Number Installation location

ø18.77 x 1.78 green 479103.0181 Shank-ø 20

ø23.52 x 1.78 green 479103.0231 Shank-ø 25

ø9.75 x 1.78 green 479103.0101 Cooling lubricant adapter

ø28.3 x 1.78 green 479103.0281 Shank-ø 30

ø37.77 x 2.62 green 319673 Shank-ø 40

ø38.60 x 2.90 red 326174 Shank-ø 40

ø12.42 x 1.78 green 479103.0121 Cooling lubricant adapter


Sealing Washer and Mounting Pin

AZ4019.00

Machine Shank sizeX

Sealing washerZ

Mounting pin

INDEX ABC VDI25 L33261.10 L33262.

INDEX C65 VDI25 L73721.80 L33262.

INDEX C100 VDI20VDI25

P63111.30L73721.80

P63151.70L33262.

INDEX C200 VDI25VDI30

L73721.80L43251.80

L33262.L43251.70

INDEX G160 VDI25VDI30

L73721.80L43251.80

L33262.L43251.70

INDEX G200 VDI25 L33261.10 L33262.


L43251.80L83291.50

L43251.70L83121.30


L43251.80L43271.80

L43251.70L43281.10

INDEX G400 VDI40 L93132.50 L43281.10

INDEX V160 VDI25VDI30

L73721.80U24111.20

L33262.L43251.70


L33261.10L43251.80

L33262.L43251.70


L43251.80L43271.80

L43251.70L43281.10

TRAUB TNX 65/42 VDI30 L43251.80 L43251.70

ZX



Product notes

INDEX ABC

9-26

W9800001EN-26.01.20110111/Rö

Product note

External/internal cooling lubricant supply Drill holder with cylindrical shank tool mounting

Offset set screws

PRODUKTBESCHREIBUNG

Disclaimer


A Word on Copyright




3Product note

W9800001EN-26.01.2011External/internal cooling lubricant supply

EXTERNAL/INTERNAL COOLING LUBRICANT SUPPLY

External/internal cooling lubricant supplyDrill holder with cylindrical shank tool mounting

Offset set screws

External cooling lubricant supply

Delivery condition

Internal cooling lubricant supply

TRAUB-DrehmaschinenGmbH & Co. KGHauffstrasse 4 D-73262 Reichenbach, Germanywww.traub.de

TECHNICAL ADVICEPhone +49 (0) 7153 502-9854Fax +49 (0) 711 [email protected]

SPARE PARTS SALESPhone +49 (0) 7153 502-600Fax +49 (0) 7153 [email protected]

INDEX-Werke GmbH & Co. KGHahn & TesskyPlochinger Strasse 92D-73730 Esslingen, Germanywww.index-werke.de



W9800004EN-20.06.20110611 /Rö

Product note

Writestar RM12/RM20

PRODUKTBESCHREIBUNG

Disclaimer


A Word on Copyright




3Product note

W9800004EN-20.06.2011Writestar RM12/RM20

TABLE OF CONTENTS

Working principle ............................................................................................................................................................... 4Applications ........................................................................................................................................................................ 4Setting the marking depth ................................................................................................................................................ 5Programming notes ........................................................................................................................................................... 5Stylus wear ........................................................................................................................................................................ 5

4 Product note


Working principleWriteStar is a marking tool that can be used on all CNC machines with an engraving software package. Marking labels are permanently created by a combination of material compaction and displacement using a special stylus.The tool requires no spindle rotation, cooling lubricant or pressurized air. The surface may be wetted with oil or cooling lubricant, but it is not necessary. Spindle speeds up to 300rpm are allowed, but they are also not necessary.

ApplicationsWriteStar is suitable for marking surfaces

- with up to 60HRC hardness. - with up to 3mm (RM12) or 5mm (RM20) unevenness. - that are non-machined or machined.

Max. 15-degree slants can be labeled evenly. The materials that can be marked include

- steel - cast - plastic - aluminum - titan

Suitable mountings are turning tool holders with 12/16/20mm or parallel shank mountings with 12 or 20mm diameter.The tool mounting clamp screws may contact the WriteStar only through a flat clamping plate, as its housing may be destroyed. The maximum allowed surface load is 500 N/cm².For optimal use of WriteStar if space is limited, INDEX TRAUB offers a range of slim drill holders http://infoshop.index-werke.de

5Product note


Setting the marking depthThe marking depth depends on the surface hardness; it can be determined by the tool infeed and by the adjusting screw on the back of the tool.The more the adjusting screw is turned in, the larger is the force acting on the stylus, resulting in a wider marking line.The standard screw-in depth is 6mm (factory setting), while the maximum depth is 15mm. Changing the screw-in depth has no effect on the tool length. Burrs can be avoided by reducing the infeed/screw-in depth.

Programming notesMany machine tool manufacturers offer subprograms for labeling with numbers, letters, and logos. If engraving software has already been used, it can also be applied for marking with WriteStar. This requires the following changes

- Reduce the spindle speed to 0rpm or to the lowest speed. - Increase the feed rate to the maximum. - Program the tool length such that the special stylus retreats 1 - 2mm (the insertion depth is not equal to the

scoring depth). - If a burr forms along the marking line or if the marking is too weak, this can be corrected using tool offset.

Stylus wearExperience shows that the stylus, when used under typical conditions and for common material hardnesses, has a life cycle of several years or more than 40km of marking length.The stylus is replaced by us. Only original styluses ensure the desired marking quality. Disassembly of the tool will void the warranty.

YouTube

Infoshop







W9800005EN-26.01.20110111/Rö

Product note

External/internal cooling lubricant supply

Drill holder with collet chuck

Offset set srew

PRODUKTBESCHREIBUNG

Disclaimer


A Word on Copyright




3Product note

W9800005EN-26.01.2011External/internal cooling lubricant supply

EXTERNAL/INTERNAL COOLING LUBRICANT SUPPLY

External/internal cooling lubricant supplyDrill holder with collet chuck

Offset set srew

External cooling lubricant supply

Delivery condition

Internal cooling lubricant supply







9-26

TRAUB-DrehmaschinenGmbH & Co. KGHauffstraße 4 D-73262 Reichenbach, Germanywww.traub.de


SPARE PARTS SALEPhone +49 (0) 7153 502-600Fax +49 (0) 7153 [email protected]

INDEX-Werke GmbH & Co. KGHahn & TesskyPlochinger Straße 92D-73730 Esslingen, Germanywww.index-werke.de


SPARE PARTS SALEPhone +49 (0) 711 3191-600Fax +49 (0) 711 [email protected]

Tool Holder Catalog - INDEX-Werkeinfoshop.index-werke.de/...ABC_Tool-holder-Catalogue_VDI25_en.pdf · Tool Holder Catalog INDEX ABC ... W9990038 Grooving tool holding block, ... W9990154

Documents