1. Install drivers 2. Locate the diagnostic connector 5. Install OBDwiz software Insert the software CD in your CD-ROM drive. From the OBDLink menu click on OBDwiz, and The scan tool selection menu will automatically follow the prompts to install the software: appear. Click on the icon labeled OBDLink: 6. Launch OBDwiz software To launch the software, click on Start Programs . Click the Auto Detect button, then click the Connect button. 3. Connect scan tool to the DLC Technical support Turn the vehicle’s ignition to the Key On, Engine Should you run into problems, technical support The OBDLink menu will appear. Click on the Off position. Follow connection diagram (bottom is just a click away: driver link for your operating system and install of page) to connect OBDLink to the diagnostic the drivers: connector using the OBD-II cable (steps & ). 4. Connect scan tool to the PC Connect OBDLink to your PC's USB port using the USB cable (steps & ). If the menu does not appear, click StartgRun, type D:\setup.exe (where ‘D’ is the drive letter of your CD-ROM drive), and click OK. With step completed, watch the LEDs as you are performing step . The "STATUS" LED will glow red (or alternate between red and amber if the Bluetooth option is installed) and the Tx/Rx LEDs will cycle on and off in sequence from left to right . The 16-pin D-shaped diagnostic link connector (DLC) should be located in the passenger or driver's compartment in the area bounded by the driver's end of the instrument panel to 300 mm (~1 ft) beyond the vehicle centerline, attached to the instrument panel and easy to access from the g driver's seat. The preferred location is between gOBDwizgOBDwiz the steering column and the vehicle centerline. — Knowledgebase - contains answers to the most commonly asked questions, general information about OBD-II, and troubleshooting information. — Forum - allows you to share information and get support from other ElmScan 5 users. These resources can be accessed from our website: A B A B C D www.ScanTool.net Quick Start A vehicle OBD-II cable USB cable computer scan tool B C D PC PC OBD POWER Tx Rx Tx Rx STATUS Tx Rx Tx Rx TM OBD OBD
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1. Install drivers 2. Locate the diagnostic connector 5. Install OBDwiz software
Insert the software CD in your CD-ROM drive. From the OBDLink menu click on OBDwiz, and The scan tool selection menu will automatically follow the prompts to install the software:appear. Click on the icon labeled OBDLink:
6. Launch OBDwiz software
To launch the software, click on StartPrograms . Click the Auto Detect button, then click the Connect button.
3. Connect scan tool to the DLC Technical supportTurn the vehicle’s ignition to the Key On, Engine Should you run into problems, technical support The OBDLink menu will appear. Click on the Off position. Follow connection diagram (bottom is just a click away:driver link for your operating system and install of page) to connect OBDLink to the diagnostic
the drivers:connector using the OBD-II cable (steps & ).
4. Connect scan tool to the PC
Connect OBDLink to your PC's USB port using the USB cable (steps & ).
If the menu does not appear, click StartgRun, type D:\setup.exe (where ‘D’ is the drive letter of your CD-ROM drive), and click OK.
With step completed, watch the LEDs as you are performing step . The "STATUS" LED will glow red (or alternate between red and amber if the Bluetooth option is installed) and the Tx/Rx LEDs will cycle on and off in sequence from left to right .
The 16-pin D-shaped diagnostic link connector (DLC) should be located in the passenger or driver's compartment in the area bounded by the driver's end of the instrument panel to 300 mm (~1 ft) beyond the vehicle centerline, attached to the instrument panel and easy to access from the g driver's seat. The preferred location is between gOBDwizgOBDwizthe steering column and the vehicle centerline.
— Knowledgebase - contains answers to the most commonly asked questions, general information about OBD-II, and troubleshooting information.
— Forum - allows you to share information and get support from other ElmScan 5 users.
These resources can be accessed from our website:
A B
AB
C D
www.ScanTool.net
Quick Start
Avehicle
OBD-II cable USB cable
computer
scan toolB C D
PCPCOBD
POWERTx Rx Tx RxSTATUSTx Rx Tx Rx
TM
OBDOBDOBD
Thank you for your purchase!
Please consider leaving feedback on:
Related Documents
![O S B L C D R OBD Cable Alfa Romeo - Crypton€¦ · AR 32310 Motronic ME 7.3.1 2,0 MT/AT Y 16 pin OBD (J1962) [Generic OBD] Supporting EOBD/OBDII MT/AT Y 16 pin OBD (J1962) ABS Bosch](https://static.cupdf.com/doc/110x72/5e8fba179483a65d5e6005b4/o-s-b-l-c-d-r-obd-cable-alfa-romeo-crypton-ar-32310-motronic-me-731-20-mtat.jpg)
