-
TM 9-2350-287-20-2VOLUME 2 OF 2
TECHNICAL MANUAL
UNIT MAINTENANCEMANUAL
FORCARRIER, AMMUNITION,
TRACKEDM992A1
(NSN 2350-01-352-3021)EIC: AE6
Approved for public release; distribution isunlimited.
HEADQUARTERS, DEPARTMENT OF THEARMY
OCTOBER 1993
HOW TO USE THE MANUALPAGE iii
BRAKES MAINTENANCEPAGE 10-1
WHEELS AND TRACKS MAINTENANCEPAGE 11-1
STEERING CONTROL LINKAGE MAINTENANCEPAGE 12-1
FRAME, TOWING ATTACHMENTS, DRAWBARS,AND ARTICULATION SYSTEMS
MAINTENANCE
PAGE 13-1SPRINGS AND SHOCK ABSORBERSMAINTENANCE PAGE 14-1
BODY, CHASSIS, AND HULL ACCESSORYMAINTENANCE PAGE 15-1BODY,
CHASSIS, AND HULL ACCESSORYITEMS MAINTENANCE PAGE 16-1
HYDRAULIC AND FLUID SYSTEMSMAINTENANCE PAGE 17-1
AUXILIARY POWER UNIT GENERATOR ANDENGINE, AND CONTROLS
MAINTENANCE
PAGE 18-1ELECTRICAL EQUIPMENT/SIGNALINGDEVICES MAINTENANCE PAGE
19-1GAGES, WEIGHING AND MEASURINGDEVICES MAINTENANCE PAGE 20-1
GLOBAL POSITIONING SYSTEM (GPS)PAGE 20.1-1
FIRE FIGHTING EQUIPMENT COMPONENTSMAINTENANCE PAGE 21-1
CHEMICAL, BIOLOGICAL, AND RADIOLOGICAL(CBR) EQUIPMENT
MAINTENANCE PAGE 22-1
APPENDIX B: MAINTENANCE ALLOCATIONCHART PAGE B-1
APPENDIX C: TORQUE VALUES FORTHREADED FASTENERS PAGE C-1
APPENDIXD: EXPENDABLEURABLE SUPPUESAND MATERIALS UST PAGE
D-1
APPENDIX E: ELECTRICAL SYSTEMSCHEMATICS PAGE E-1APPENDIX F:
HYDRAULIC SYSTEMSCHEMATIC PAGE F-1
APPENDIX G: LUBRICATION INSTRUCTIONSPAGE G-1
APPENDIX H: MANDATORY REPLACEMENTPARTS LIST PAGE H-1
APPENDIX I: TOOLS/TEST EQUIPMENTPAGE I-1
APPENDIX J: ILLUSTRATED LIST OFMANUFACTURED ITEMS PAGE J-1
INDEXPAGE INDEX 1
Change 1
-
TM 9-2350-287-20-2
TECHNICAL MANUAL HEADQUARTERSDEPARTMENT OF THE ARMY
NO. 9-2350-287-20-2 Washington, D.C., 22 OCTOBER 1993
UNIT MAINTENANCE MANUALFOR
CARRIER, AMMUNITION, TRACKEDM992A1
(NSN 2350-01-352-3201)EIC:AE6
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this manual. If you find any mistakes or if
you know of a way toimprove the procedures, please let us know.
Mail your letter, DA Form 2028(Recommended Changes to Publications
and Blank Forms), or DA Form 2028-2 locatedin the back of this
manual directly to Commander, U.S. Army Tank-automotive
andArmaments Command, ATTN: AMSTA-IM-OPIT, Warren, MI 48397-5000. A
reply willbe furnished to you.
You may also provide DA Form 2028-2 information to TACOM via
datafax or e-mail:• TACOM's fax number is DSN 786-6323 or
Commercial (810) 574-6323• TACOM's e-mail address is
tacom-tech-pubs@ cc.tacom.army.mil
Approved for public release; distribution is unlimited.
TABLE OF CONTENTS
Volume 2Page
How To Use This Manual
...................................................................................................................................
iii
CHAPTER 10 BRAKES MAINTENANCE
.......................................................................................10-1
CHAPTER 11 WHEELS AND TRACKS MAINTENANCE
...............................................................11-1
CHAPTER 12 STEERING CONTROL LINKAGE MAINTENANCE
..................................................12-1
CHAPTER 13 FRAME, TOWING ATTACHMENTS, DRAWBARS,AND ARTICULATION
SYSTEMS MAINTENANCE
..................................................13-1
CHAPTER 14 SPRINGS AND SHOCK ABSORBERS MAINTENANCE
.........................................14-1
CHAPTER 15 BODY, CAB, HOOD, AND HULL MAINTENANCE
...................................................15-1
CHAPTER 16 BODY, CHASSIS, AND HULL ACCESSORY ITEMSMAINTENANCE
........................................................................................................16-1
CHAPTER 17 HYDRAULIC AND FLUID SYSTEMS MAINTENANCE
............................................17-1
Change 1 i
-
TM 9-2350-287-20-2
Page
CHAPTER 18 AUXILIARY POWER UNIT GENERATOR AND ENGINE,AND
CONTROLS MAINTENANCE
...........................................................................18-1
CHAPTER 19 ELECTRICAL EQUIPMENT/SIGNALING DEVICESMAINTENANCE
.......................................................................................................19-1
CHAPTER 20 GAGES, WEIGHING AND MEASURING DEVICESMAINTENANCE
........................................................................................................20-1
CHAPTER 20.1 GLOBAL POSITIONING SYSTEM (GPS)
.............................................................
20.1-1
CHAPTER 21 FIRE FIGHTING EQUIPMENT COMPONENTSMAINTENANCE
........................................................................................................21-1
CHAPTER 22 CHEMICAL, BIOLOGICAL, AND RADIOLOGICAL(CBR) EQUIPMENT
MAINTENANCE........................................................................22-1
APPENDIX A REFERENCES
...........................................................................................................
A-1
APPENDIX B MAINTENANCE ALLOCATION CHART
...................................................................
B-1
SECTION I Introduction
................................................................................................................
B-1
SECTION II Maintenance Allocation Chart for Carrier, Ammunition,
Tracked, M992A1 .................. B-4
SECTION III Tool and Test Equipment Requirements
...................................................................B-21
APPENDIX C TORQUE VALUES FOR THREADED FASTENERS
................................................. C-1
APPENDIX D EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST
................................ D-1
SECTION I Introduction
................................................................................................................
D-1
SECTION II Expendable Supplies and Materials List
.....................................................................
D-2
APPENDIX E ELECTRICAL SYSTEM SCHEMATICS
.....................................................................
E-1
APPENDIX F HYDRAULIC SYSTEM SCHEMATIC
.........................................................................F-1
APPENDIX G LUBRICATION INSTRUCTIONS
...............................................................................
G-1
APPENDIX H MANDATORY REPLACEMENT PARTS LIST
.......................................................... H-1
APPENDIX I TOOLS/TEST EQUIPMENT
........................................................................................I-1
APPENDIX J ILLUSTRATED LIST OF MANUFACTURED ITEMS
................................................... J-1
INDEX
.............................................................................................................................
Index 1
Change 1 ii
-
TM 9-2350-287-20-2
HOW TO USE THIS MANUAL
SCOPE.
This technical manual contains Unit maintenance procedures for
the M992A1 Carrier Ammunition, Tracked. Chapter1 contains general
information; Chapter 2 contains information on general maintenance
procedures and describes andillustrates troubleshooting procedures;
and Chapters 3 through 22 describe and illustrate maintenance
procedures forvarious systems and components. Ten appendixes and a
subject index are also included in this manual.
INDEXING.
Four indexing procedures are used to help you locate information
quickly:
Cover index. Lists chapter titles and important parts of the
manual, with corresponding page numbers.Each chapter or part listed
is boxed in, with a black outer edge that is in line with the first
page of that chapteror part.
Table of contents. The table of contents follows the Safety
Summary. The table of contents lists allchapters numerically, with
corresponding page numbers.
Chapter indexes. Each chapter starts with a numerical listing of
all paragraphs in that chapter.
Alphabetical index. The alphabetically arranged subject index
starts on page Index 1.
MAINTENANCE TEXT AND ILLUSTRATIONS (CHAPTERS 3 THROUGH 22).
Each chapter begins with a numerical listing of all paragraphs.
The first paragraph in each chapter is titled “General”and
describes the system(s) to be covered. General repair and
inspection procedures may also be given.
Each paragraph contains the following information, as
appropriate:
The common or specials tools and test equipment required to
perform the procedures are listed under theheading “Tools/Test
Equipment.” Common and special tools are listed in Appendix I.
Materials and mandatory replacement parts that will be discarded
during the procedure are listed underthe heading “Materials/Parts.”
A Materials/Parts list does not contain items that maybe replaced
if founddefective during inspection. Also, the list does not
contain the item named in the paragraph title.Materials may be
found in Appendix D. Mandatory replacement parts maybe found in
Appendix H.Refer to TM 9-2350-287-24P for information on other
parts that may have to be replaced.
If more than one person is required to perform the procedure,
the number is specified under the heading“Personnel Required.”
Technical manuals, technical bulletins, field manuals, or other
reference material that maybe requiredto perform the procedure are
listed under the heading “References.” Note that the titles of all
publicationsand forms referenced in the manual are listed in
Appendix A,
Procedures that must be performed on the vehicle prior to the
maintenance procedure are listed underthe heading “Equipment
Conditions.”
iii
-
TM 9-2350-287-20-2
TEXT AND ILLUSTRATIONS.
Maintenance procedures are to be performed in the sequence given
in the text and illustrations.
Illustrations are numbered clockwise, beginning at the 11
o’clock position. Because an illustration is keyed to the
text,parts that are removed sequentially may not have sequential
numbers. For example:
1. Remove screw (4), Iockwasher (6), washer (7), and bracket (5)
from transmission.
IMPORTANT.
Be sure to read the entire paragraph before beginning a
maintenance procedure. Also, read the general informationin Chapter
1 before beginning a procedure.
Warnings and cautions appear immediately preceding the step to
which they pertain. It is important to read andthoroughly
understand the warnings and/or cautions before beginning
maintenance.
Notes may precede or follow the steps to which they pertain,
depending on what makes the most sense. Notes highlightessential
operating or maintenance procedures, conditions, or statements.
PROBLEM SOLVING.
The best way for you to fulfill your responsibility for
maintaining the equipment covered in this manual is to makemaximum
use of your maintenance manual. The following three sample problems
illustrate ways to use the manualefficiently:
1. How do I replace the roadwheel hub?
• Look in the subject index for "roadwheel hub replacement” and
turn to theappropriate page.
2. An equipment condition for replacing surge tank hoses (para
6-4) is, “Powerpackremoved (para 3-2). ” How do I find out what
page paragraph 3-2 begins on?
• Look in the chapter index for Chapter 3 until you find
paragraph 3-2, PowerpackReplacement; then turn to the appropriate
page.
3. The auxiliary power unit (APU) engine won’t start. How do I
find out what’s wrong?
Turn to the Quick Guide to Troubleshooting (para 2-18). Find the
name of the itemthat doesn’t work (APU).
Find the problem (ENGINE CRANKS BUT FAILS TO START) in the
listing for APU.
Turn to the paragraph in the Troubleshooting Chart (para 2-19)
that is referenced-in this case, paragraph 2-19u (1).
iv
-
TM 9-2350-287-20-2
CHAPTER 10BRAKES MAINTENANCE
Paragraph PageNumber Paragraph Title Number
10-1 General . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .. .10-110-2 Service and Parking Brake Linkage
Replacement/Adjustment . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-3
Powerpack Compartment Brake Linkage Replacement/Adjustment . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . 10-610-4 Driver’s Compartment Brake Assembly Repair . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.10-10
10-1. GENERAL.
This chapter illustrates and describes the removal, installation
and adjustment of the brake system. The followingprocedures are
addressed:
Service and Parking Brake Linkage
Replacement/AdjustmentPowerpack Compartment Brake Linkage
Replacement/AdjustmentDriver’s Compartment Brake Assembly
Repair
10-2. SERVICE AND PARKING BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT.
This task covers:
a. Removal b. Disassemblyc. Cleaning and Inspection d.
Assemblye. Installation f. Adjustment
Initial Setup:
Tools/Test Equipment: • Spring (Item 346, Appendix H)• General
mechanic’s tool kit (Item 24, • Spring (Item 347, Appendix H)
Appendix I) • Spring pin (2) (Item 353, Appendix H)
Materials/Parts: Equipment Conditions:• Drycleaning solvent
(Item 28, Appendix D) • Vehicle parked on level ground (refer• Rag
(Item 56, Appendix D) to TM 9-2350-287-10).• Cotter pin (Item 27,
Appendix H) • Track blocked (refer to TM 9-2350-287-10).•
Lockwasher (2) (Item 175, Appendix H) • Parking brake released
(refer to• Lockwasher (2) (Item 177, Appendix H) TM 9-2350-287-1
0).
10-1
-
TM 9-2350-287-20-2
10-2. SERVICE AND PARKING BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT(continued).
a. REMOVAL
1. Remove screw (1) and Iockwasher (2) frombellcrank (3).
Discard Iockwasher.
2. Remove two screws (5) and Iockwashers (6)from angle bracket
(7). Discard Iockwashers.
NOTE
Support service and parking brakelinkage by hand.
3. Pull bellcrank (3) off bracket spindle (4), andremove brake
linkage (8) from vehicle.
b. DISASSEMBLY
1. Remove spring pin (14) andend of brake control rod (9).
brake handle (13) fromDiscard spring pin.
2.
3.
WARNING
Use care when removing spring. Spring is under tension and can
act as a projectilewhen released and could cause severe eye
injury.
Remove angle bracket (7), two washers (11), and spring (12) from
brake control rod (9). Discard spring.
Remove spring pin (15) and collar (1 0) from brake control rod
(9). Discard spring pin.
10-2
-
TM 9-2350-287-20-2
10-2. SERVICE AND PARKING BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT(continued).
4.
5.
6.
7.
8.
c.
1.
2.
d.
1.
2.
3.
4.
5.
WARNING
Use care when removing spring. Spring is under tension and can
act as a projectilewhen released and could cause severe eye
injury.
Remove cotter pin (20), two washers (24), spring (23), rod guide
(22), and washer (21) from brake controlrod (19). Discard cotter
pin and spring.
Remove screw (27), Iockwasher (26), washer (25), and rod guide
(22) from bellcrank (3). DiscardIockwasher.
Loosen two nuts (16 and 18) and remove two brake control rods (9
and 19) from mechanical post (17).
Remove nut (18) and two nuts (28) from brake control rod
(19).
Remove nut (16) from brake control rod (9).
CLEANING AND INSPECTION
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Always wear
protective gogglesand gloves, and use only in a well-ventilated
area. Avoid contact with skin, eyes, andclothes, and DO NOT breathe
vapors. DO NOT use near open flame or excessive heat.
Clean all parts with drycleaning solvent and rag.
Inspect all parts for damage. Replace any damaged parts.
ASSEMBLY
Install nut (16) on brake control rod (9).
Install two nuts (28) and nut (18) on brake control rod
(19).
Install two brake control rods (9 and 19) in mechanical post
(17), then tighten two nuts (16 and 18).
WARNING
Use care when installing spring. Spring is under tension and can
act as a projectilewhen released and could cause severe eye
injury.
Install washer (21), rod guide (22), new spring (23), and two
washers (24) on end of brake control rod (19),and secure with new
cotter pin (21 ).
Install bellcrank (3) on rod guide (22) and secure with screw
(27), washer (25), and new Iockwasher (26).
10-3
-
TM 9-2350-287-20-2
10-2. SERVICE AND PARKING BRAKE LINKAGE REPLACEMENT/ADJUSTMENT
(continued).
6. Install collar (10) on end of brake control rod (9) and
secure with new spring pin (15).
WARNING
Use care when installing spring. Spring is under tension and can
act as a projectilewhen released and could cause severe eye
injury.
7. Install two washers (11), new spring (12), and angle bracket
(7) on brake control rod (9).
8. Install brake handle (13) on end of brake control rod (9) and
secure with new spring pin (14).
e. INSTALLATION
1. Position brake linkage (8) and bellcrank (3)
2.
in place on bracket spindle (4).
Install two screws (5) and new Iockwashers(6) on angle bracket
(7).
3. Install screw (1) and new Iockwasher (2) tosecure bellcrank
(3) on bracket spindle (4).
4. Adjust service and parking brake linkage(para 10-2).
10-4
-
10-2. SERVICE AND PARKING BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT(continued).
f.
1.
2.
3.
4.
5.
6.
7.
ADJUSTMENT
Remove two screws (5) and Iockwashers (6) to loosen angle
bracket (7). Discard bckwashers.
Loosen two nuts (16 and 18) on brake control rods (9 and
19).
Turn mechanical post (17) in either direction until screw holes
in angle bracket (7) lineup with mounting holesin bulkhead and no
pressure is on bellcrank (3).
Install two screws (5) and new Iockwashers (6) to secure angle
bracket (7) to bulkhead.
Tighten two nuts (16 and 18) on brake control rods (9 and
19).
Depress service brake pedal (29), and pull brake handle (13) to
lock parking brake.
Release service brake pedal (29). Brake should stay locked; if
it does not, repeat steps 1 through 6.
FOLLOW-ON MAINTENANCE:• Adjust parking brake light switch (para
7-20).• Unblock tracks (refer to TM 9-2350-287-10).
10-5
TM 9-2350-287-20-2
-
TM 9-2350-287-20-2
10-3. POWERPACK COMPARTMENT BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT.
This task covers:
a. Removal b. Disassemblyc. Cleaning and Inspection d.
Assemblye. Installation f. Adjustment
Initial Setup:
Tools/Test Equipment:• GeneraI mechanic’s tool kit (Item 24,
Appendix I)
Materials/Parts:• Drycleaning solvent (Item 28, Appendix D)• Rag
(Item 56, Appendix D)• Cotter pin (4) (Item 17, Appendix H)•
Lockwasher (Item 176, Appendix H)• Spring pin (2) (Item 367,
Appendix H)
Equipment Conditions:• Vehicle parked on level ground
(refer to TM 9-2350-287-10).• Parking brake released (refer
to
TM 9-2350-287-10).• Transmission doors opened (refer to
TM 9-2350-287-10).• Track blocked (refer to TM
9-2350-287-10).
a.
1.
2.
3.
4.
REMOVAL
Remove quick-release pin (9) anddisconnect shift linkage (11)
from rod(10).
Remove cotter pin (4) and pin (5) fromlever (8) and disconnect
powerpackcompartment brake linkage (6) fromlever (8). Discard
cotter pin.
Remove Screw (1), Iockwasher (2), andwasher (3) from shaft (7).
DiscardIockwasher.
Remove powerpack compartmentbrake linkage (6) from shaft
(7).
10-6
-
TM 9-2350-287-20-2
10-3. POWERPACK COMPARTMENT BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT(continued).
b. DISASSEMBLY
1. Loosen nut (20) on rod end (21). Unscrew and remove rod end
(21) from clevis(19).
2. Remove cotter pin (18), pin (17), sprocket (23), and chain
(22) from clevis (19). Discard cotter pin.
3. Remove two cotter pins (16), pins (15), and clevises (13) and
chain (22) from right brake lever (24) and leftbrake lever (12).
Discard cotter pins.
4. Remove two spring pins (14) from two clevises (13), and
separate chain (22) from two clevises (13). Discard
c.
1.
2.
d.
1.
2.
spring pins.
WARNING
Drycleaning solvent P-D-680 is toxic and flammable. Always wear
protective gogglesand gloves and use only in a well-ventilated
area. Avoid contact with skin, eyes, andclothes, and DO NOT breathe
vapors. DO NOT use near open flame or excessive heat.
Clean all parts with drycleaning solvent and rag.
Inspect all parts for damage. Replace any damaged parts.
ASSEMBLY
Install two clevises (13) on ends of chain (22) with two new
spring pins (14).
Position chain (22) and two clevises (13) in place on sprocket
(23).
CLEANING AND INSPECTION
10-7
-
TM 9-2350-287-20-2
10-3. POWERPACK COMPARTMENT BRAKE LINKAGE REPLACEMENT/ADJUSTMENT
_(continued).
3.
4.
5
e.
1.
2.
3.
4.
Position two clevises (13) in place on left brake lever (12) and
right brake lever (24) and secure with two pins(15) and new cotter
pins (16).
Install sprocket (23) and chain (22) in clevis(19) and secure
with pin (17) and new cotter pin (18).
Screw rod end (21) in clevis (19).
INSTALLATION
Position powerpack compartmentbrake linkage (6) in place on
shaft (7).
Install screw (1), new Iockwasher (2),and washer (3) in shaft
(7).
Install rod end (21 ) in lever (8) andsecure with pin (5) and
new cotter pin(4).
Connect shift linkage (11 ) to rod (10)and install quick-release
pin (9).
10-8
-
TM 9-2350-287-20-2
10-3. POWERPACK COMPARTMENT BRAKE LINKAGE
REPLACEMENT/ADJUSTMENT(continued).
f.
1.
2.
3.
4.
5.
6.
7.
ADJUSTMENT
With brake pedal fully raised, check for slack in chain (22) and
alinement of brake lever index marks (25)with release mark (26). If
index marks are alined, no adjustment is necessary.
Remove cotter pin (4) and pin (5) from lever (8). Discard cotter
pin.
Loosen nut (20) on rod end (21).
Rotate rod end (21) until all slack is removed from chain (22),
holes in rod end (21) and lever (8) are alined,and brake lever
index marks (25) are at release mark (26).
Install pin (5) and new cotter pin (4) on lever (8).
Check release marks (26) for alinement with brake lever index
marks (25).
Tighten nut (20) against rod end (21).
FOLLOW-ON MAINTENANCE:• Close transmission doors (refer to TM
9-2350-287-10).• Adjust stoplight switch (para 7-20).
10-9
-
TM 9-2350-287-20-2
10-4. DRIVER’S COMPARTMENT BRAKE ASSEMBLY REPAIR.
This task covers:
a. Removal b. Disassemblyc. Cleaning and Inspection d.
Assemblye. Installation f. Adjustment
Initial Setup:
Tools/Test Equipment:• General mechanic’s tool kit (Item
24,Appendix I)
• Snapring pliers (Item 53, Appendix I)
Materials/Parts:• Drycleaning solvent (Item 28, Appendix D)• Rag
(Item 56, Appendix D)• Boot (Item 5, Appendix H)• Cotter pin (2)
(Item 17, Appendix H)• Cotter pin (Item 24, Appendix H)• Gasket
(Item 95, Appendix H)• Lockwasher (4) (Item 175, Appendix H)•
Lockwasher (4) (Item 177, Appendix H)• Lockwire (Item 202, Appendix
H)• Retaining ring (Item 244, Appendix H)
• Seal (Item 269, Appendix H)• Seal (Item 293, Appendix H)•
Self-locking nut (10) (Item 312, Appendix H)• Self-locking nut (3)
(Item 315, Appendix H)• Self-locking nut (Item 330, Appendix H)
a. REMOVAL
1.
2.
3.
Remove quick-release pin (1) anddisconnect shift linkage (3)
fromrod (2).
Remove cotter pin (10), straightpin (7), and lever (8) from rod
endbearing (9). Discard cotter pin.
Remove screw (1), washer (12),and lever (8) from shaft (5).
Equipment Conditions:• Vehicle parked on level ground (refer
toTM 9-2350-287-10).
• Track blocked (refer to TM 9-2350-287-10).• Left and right
transmission access doors opened
(refer to TM 9-2350-287-10).• Parking brake light switch and
bracket removed
(para 7-20).• Center driver's periscope removed
(refer to TM 9-2350-287-10).
10-10
TOCLAST_CHANGEWARNINGCHAPTERSCHAPTER 10CHAPTER 11CHAPTER
12CHAPTER 13CHAPTER 14CHAPTER 15CHAPTER 16CHAPTER 17CHAPTER
18CHAPTER 19CHAPTER 20CHAPTER 20.1CHAPTER 21CHAPTER 22
PARAGRAPHSPARA 10-1PARA 10-2PARA 10-3PARA 10-4PARA 11-1PARA
11-2PARA 11-3PARA 11-4PARA 11-5PARA 11-6PARA 11-7PARA 11-8PARA
11-9PARA 11-10PARA 11-11PARA 11-12PARA 11-13PARA 11-14PARA 12-1PARA
12-2PARA 13-1PARA 13-2PARA 13-3PARA 13-4PARA 14-1PARA 14-2PARA
14-3PARA 15-1PARA 15-2PARA 15-3PARA 15-4PARA 15-5PARA 15-6PARA
15-7PARA 15-8PARA 15-9PARA 15-10PARA 15-11PARA 15-12PARA 15-13PARA
15-14PARA 15-15PARA 15-16PARA 15-17PARA 15-18PARA 15-19PARA
15-20PARA 15-21PARA 15-22PARA 15-24PARA 15-25PARA 15-26PARA
15-27PARA 15-28PARA 15-29PARA 15-30PARA 15-31PARA 15-32PARA
15-33PARA 15-34PARA 15-37PARA 15-35PARA 15-36PARA 15-38PARA
15-39PARA 15-40PARA 15-41PARA 15-42PARA 15-43PARA 15-44PARA
15-45PARA 15-46PARA 15-47PARA 15-48PARA 15-49PARA 15-50PARA
15-51PARA 15-52PARA 15-53PARA 15-54PARA 15-55PARA 15-56PARA
15-57PARA 15-58PARA 15-59PARA 15-60PARA 15-61PARA 15-62PARA
15-63PARA 15-64PARA 15-65PARA 15-66PARA 15-67PARA 15-68PARA
15-69PARA 15-70PARA 15-71PARA 15-72PARA 15-73PARA 15-74PARA
15-75PARA 15-76PARA 15-77PARA 15-78PARA 15-79PARA 15-80PARA
15-81PARA 15-82PARA 15-83PARA 15-84PARA 15-85PARA 15-86PARA
15-87PARA 15-88PARA 15-89PARA 15-90PARA 15-91PARA 15-92PARA
15-93PARA 15-94PARA 16-1PARA 16-2PARA 16-3PARA 16-4PARA 16-5PARA
16-6PARA 16-7PARA 16-8PARA 16-9PARA 16-10PARA 17-1PARA 17-2PARA
17-3PARA 17-4PARA 17-5PARA 17-6PARA 17-7PARA 17-8PARA 17-9PARA
17-10PARA 17-11PARA 17-12PARA 17-13PARA 17-14PARA 17-15PARA
17-16PARA 17-17PARA 17-18PARA 17-19PARA 17-20PARA 17-21PARA
17-28PARA 17-29PARA 17-30PARA 17-31PARA 17-32PARA 17-34PARA
17-35PARA 18-1PARA 18-2PARA 18-3PARA 18-4PARA 18-5PARA 18-6PARA
18-7PARA 18-8PARA 18-9PARA 18-10PARA 18-11PARA 18-12PARA 18-13PARA
18-14PARA 18-15PARA 18-16PARA 18-17PARA 18-18PARA 18-19PARA
18-20PARA 18-21PARA 18-22PARA 18-23PARA 18-24PARA 18-25PARA
18-26PARA 18-27PARA 18-28PARA 18-29PARA 19-1PARA 19-2PARA 19-3PARA
19-4PARA 19-5PARA 19-6PARA 20-1PARA 20-2PARA 20.1-1PARA 20.1-2PARA
20.1-3PARA 20.1-4PARA 20.1-5PARA 21-1PARA 21-2PARA 21-3PARA
21-4PARA 21-5PARA 21-6PARA 21-7PARA 21-8PARA 21-9PARA 21-10PARA
21-11PARA 21-12PARA 21-13PARA 21-14PARA 21-15PARA 21-16PARA
22-1PARA 22-2PARA 22-3PARA 22-4PARA 22-5PARA 22-6PARA 22-7PARA
A-1PARA A-2PARA A-3PARA A-4PARA A-5PARA B-1PARA B-2PARA B-3PARA
B-4PARA C-1PARA C-2PARA C-3PARA C-4PARA C-5PARA C-6PARA D-1PARA
D-2PARA E-1PARA E-2PARA F-1PARA F-2PARA H-1PARA H-2PARA I-1PARA
I-2PARA J-1PARA J-2
TABLESTABLE 11-1TABLE C-1TABLE C-2TABLE C-3TABLE C-4TABLE
C-5TABLE H-1TABLE I-1TABLE 1
APPENDICESAPP AAPP BAPPB_SECTION IAPPB_SECTION IIAPPB_SECTION
IIIAPP CAPP DAPPD_SECTION IAPPD_SECTION IIAPP EAPP FAPP GAPP HAPP
IAPP J
INDEXPAGESPAGE IPAGE IIPAGE IIIPAGE 10-1PAGE 10-6PAGE 10-10PAGE
11-1PAGE 11-5PAGE 11-6PAGE 11-8PAGE 11-9PAGE 11-10PAGE 11-11PAGE
11-16PAGE 11-17PAGE 11-19PAGE 11-20PAGE 11-22PAGE 11-23PAGE
11-24PAGE 11-25PAGE 11-27PAGE 11-28PAGE 11-32PAGE 11-37PAGE
12-1PAGE 13-1PAGE 13-2PAGE 13-6PAGE 13-7PAGE 14-1PAGE 14-4PAGE
15-1PAGE 15-3PAGE 15-4PAGE 15-8PAGE 15-9PAGE 15-10PAGE 15-12PAGE
15-14PAGE 15-16PAGE 15-17PAGE 15-19PAGE 15-20PAGE 15-21PAGE
15-25PAGE 15-28PAGE 15-29PAGE 15-30PAGE 15-33PAGE 15-34PAGE
15-37PAGE 15-40PAGE 15-42PAGE 15-44PAGE 15-45PAGE 15-46PAGE
15-51PAGE 15-52PAGE 15-53PAGE 15-57PAGE 15-60PAGE 15-62PAGE
15-65PAGE 15-66PAGE 15-69PAGE 15-72PAGE 15-78PAGE 15-82PAGE
15-83PAGE 15-84PAGE 15-88PAGE 15-89PAGE 15-90PAGE 15-93PAGE
15-97PAGE 15-99PAGE 15-101PAGE 15-102PAGE 15-104PAGE 15-108PAGE
15-109PAGE 15-111PAGE 15-117PAGE 15-119PAGE 15-120PAGE 15-123PAGE
15-124PAGE 15-125PAGE 15-128PAGE 15-129PAGE 15-130PAGE 15-133PAGE
15-135PAGE 15-138PAGE 15-140PAGE 15-141PAGE 15-143PAGE 15-145PAGE
15-147PAGE 15-148PAGE 15-149PAGE 15-156PAGE 15-166PAGE 15-170PAGE
15-174PAGE 15-175PAGE 15-177PAGE 15-178PAGE 15-180PAGE 15-182PAGE
15-183PAGE 15-184PAGE 15-185PAGE 15-188PAGE 15-189PAGE 15-190PAGE
15-191PAGE 15-192PAGE 15-194PAGE 15-195PAGE 15-198PAGE 15-203PAGE
15-209PAGE 15-211PAGE 15-213PAGE 15-214PAGE 15-223PAGE 15-224PAGE
15-233PAGE 15-234PAGE 15-235PAGE 15-236PAGE 15-240PAGE 15-242PAGE
15-243PAGE 15-245PAGE 15-247PAGE 15-248PAGE 16-1PAGE 16-4PAGE
16-6PAGE 16-8PAGE 16-12PAGE 16-15PAGE 16-18PAGE 16-20PAGE 16-22PAGE
17-1PAGE 17-2PAGE 17-3PAGE 20-1PAGE 17-4PAGE 17-6PAGE 17-7PAGE
17-8PAGE 17-11PAGE 17-13PAGE 17-20PAGE 17-24PAGE 17-26PAGE
17-28PAGE 17-30PAGE 17-32PAGE 17-36PAGE 17-40PAGE 17-42PAGE
17-43PAGE 17-47PAGE 17-49PAGE 17-50PAGE 17-57PAGE 17-59PAGE
17-60PAGE 17-81PAGE 17-82PAGE 17-85PAGE 17-88PAGE 17-93PAGE
17-94PAGE 17-98PAGE 17-103PAGE 17-104PAGE 17-107PAGE 17-108PAGE
17-115PAGE 17-120PAGE 17-123PAGE 17-126PAGE 18-1PAGE 18-2PAGE
18-8PAGE 18-9PAGE 18-12PAGE 18-13PAGE 18-18PAGE 18-20PAGE 18-21PAGE
18-23PAGE 18-25PAGE 18-32PAGE 18-35PAGE 18-36PAGE 18-40PAGE
18-42PAGE 18-44PAGE 18-47PAGE 18-48PAGE 18-50PAGE 18-51PAGE
18-52PAGE 18-54PAGE 18-57PAGE 18-58PAGE 18-60PAGE 18-62PAGE
18-63PAGE 18-65PAGE 18-67PAGE 18-70PAGE 18-74PAGE 19-1PAGE 19-4PAGE
19-5PAGE 19-6PAGE 19-7PAGE 19-8PAGE 20.1-1PAGE 20.1-4PAGE
20.1-5PAGE 20.1-6PAGE 20.1-8PAGE 21-1PAGE 21-2PAGE 21-4PAGE
21-7PAGE 21-12PAGE 21-16PAGE 21-21PAGE 21-25PAGE 21-29PAGE
21-37PAGE 21-40PAGE 21-48PAGE 21-49PAGE 21-50PAGE 21-52PAGE
21-54PAGE 21-56PAGE 22-1PAGE 22-4PAGE 22-6PAGE 22-7PAGE 22-21PAGE
22-23PAGE A-1PAGE A-2PAGE A-3PAGE B-1PAGE B-2PAGE B-3PAGE B-4PAGE
B-5PAGE B-10PAGE B-15PAGE B-20PAGE B-21PAGE B-23PAGE C-1PAGE
C-3PAGE C-4PAGE C-5PAGE D-1PAGE D-2PAGE D-3PAGE D-6PAGE E-1PAGE
E-2PAGE E-3PAGE E-4PAGE E-5PAGE E-6PAGE E-7PAGE E-8PAGE E-9PAGE
E-10PAGE E-11PAGE E-12PAGE E-13PAGE E-14PAGE E-15PAGE E-16PAGE
E-17PAGE E-18PAGE E-19PAGE E-20PAGE E-21PAGE E-22PAGE E-23PAGE
E-24PAGE E-25PAGE E-26PAGE E-27PAGE E-28PAGE E-29PAGE E-30PAGE
E-31PAGE E-32PAGE E-33PAGE E-34PAGE E-35PAGE E-36PAGE E-37PAGE
E-38PAGE E-39PAGE E-40PAGE E-41PAGE E-42PAGE E-43PAGE E-44PAGE
E-45PAGE E-46PAGE E-47PAGE E-48PAGE E-49PAGE E-50PAGE E-51PAGE
E-52PAGE E-53PAGE E-54PAGE E-55PAGE E-56PAGE E-57PAGE E-58PAGE
E-59PAGE E-60PAGE E-61PAGE E-62PAGE E-63PAGE E-64PAGE F-1PAGE
F-2PAGE G-1PAGE H-1PAGE H-2PAGE H-3PAGE I-1PAGE I-2PAGE J-1PAGE
J-2PAGE J-5PAGE J-6PAGE INDEX 1PAGE INDEX 2PAGE INDEX 5PAGE INDEX
8