TLILIC0003 LICENCE TO OPERATE A FORKLIFT TRUCK Learning Materials Version 3
TLILIC0003 LICENCE TO
OPERATE A FORKLIFT TRUCK
Learning Materials
Version 3
1
TLILIC0003 Licence to operate a forklift truck Version 3
Disclaimer
Any provider using this material should independently ensure that instructional material is
customised and covers all applicable State, Territory and Federal regulatory licencing
requirements. The information within the material does not comprise professional advice and
must be customised and delivered by a suitably qualified professional Provider. The material
(as a single source) should not be relied upon in any important matter without obtaining
appropriate advice from subject matter experts relevant to your circumstances.
Publication Published by the Civil Contractors Federation SA
ABN: 65 484 720 549
CCF SA Branch
1 South Road
Thebarton SA, 5031
Phone: 08 8111 8000
Fax: 08 8111 8002
First published November 2012
Copyright © 2014 Civil Contractors Federation SA
All rights reserved. No part of this publication may be reproduced or transmitted in any form
or by any means, electronic or mechanical, including photocopying, scanning, recording, or
any information storage and retrieval system, without permission in writing from the Civil
Contractors Federation SA. No liability is assumed with respect to the use of information
contained herein. While all due care has been taken in preparing this book, the publisher, the
distributor and authors assume no responsibility for errors or omissions. Neither is any liability
assumed for damages resulting from the use of the information contained herein.
Feedback If you have any suggestions for improving this workbook, please send to:
Version Control:
2
TLILIC0003 Licence to operate a forklift truck Version 3
Date Changes Version By
19/11/12 Change of format
Updated information:
• To include learning checks
• To be appropriate for the new calculations assessment
• Inclusion of the hierarchy of control and duty of care
• Updated diagrams for Load centre distance and stability
triangle
• Inserted example of data plate to explain rated capacity
V2 P. Wanders and
V. Griffith
22/03/12 Update information
• Assessment re-sit timeline changed
• Added legislation (pg. 11)
• Inserted section 1: Legislation
• Changes some wording to sections:
7, 8, 9, 12, 13 (plus addition of tiger tails), 15, 16.
• Inserted calculation methodology (section 17)
V2.1 P. Wanders
03/05/13 Minor change – page numbers and contents corrected V2.2 V. Griffith
08/01/14 Review content and wording:
• Minor changes for WHS terminology throughout
• Re-formatted and page number update
• Pg. 11 – minor wording change
• Section 3 - changed wording and examples of hierarchy of
control
• Section 6 – change of wording
• Section 7 – change of wording
• Section 8 – change of wording
• Sections 9 and 10 – minor word change
• 12.2 removed (when tilting the load)
• 12.2 (v2.3) – change of wording
• Addition of 12.3 (placement of load)
• Section 13 – change of wording
• Section 14 – change of wording
• Addition of ‘Communication’ (now section 15).
• Section 17 (v2.3) – change of wording
V2.3 S.Young and
Paul Wanders
18/11/14 • Added to lists in section 6.1
• Additions to learning checklists 1 and 2
• Addition of 24 question pre-assessment check
• Removed 9.1 (slings, chians and shackles)
V2.4 S.Young
M.Williams
1/7/16 • Changed TLILIC2001A to TLILIC2001, updated to align with
the Standards for Training Packages
• Changed feedback contact from:
[email protected] to: [email protected]
• Changed spacing Section 1.1 between
“legislation.Regulations” to legislation. Regulations.
• Changed spacing Section 1.2 between “workare” to work
are.
• Changed Section 3, Personal Protective Equipment (PPE)
spacing between “haveproven” and “relieson” to have
proven and relies on.
• Changed Section 12.2, Travelling, paragraph 17. Changed
start of paragraph “if’ to If and changed “.grab” to . Grab.
• Added three additional calculations for learner
• Formatted and updated Self Check Questions, 25 questions.
V2.5 M.Blackborough
29/3/17 • Updated unit of competency information on pages 9 -12 V2.6 V.Griffith
18/12/17 • Reword section 1 on HRWL and inserted Learning Check 1
• Extracted power lines information (will provide separate
handouts for SA and NT from respective regulators)
• Add NT WHS legislation to 2.1
• Changed 60kg to 35kg in 13.1
V2.7 V.Griffith
08/01/19 • Re-install safe working distances from electricity V2.8 V.Griffith
4/07/19 • Updated resource to meet TLILIC0003 requirements V3 M. Blackborough
3
TLILIC0003 Licence to operate a forklift truck Version 3
Contents
INTRODUCTION ......................................................................................... 5
UNIT OF COMPETENCY ............................................................................. 8
1. APPLYING FOR A HIGH RISK WORK LICENCE (HRWL) ...................... 13
Learning Check 1 .................................................................................. 15
2. INTRODUCTION.................................................................................. 16
2.1 Legislation, Regulations and Codes of Practice ......................... 16
2.2 Organisational and workplace standards ................................... 16
3. THE FORKLIFT TRUCK .......................................................................... 17
3.1 Counterbalanced forklift trucks .................................................. 17
3.2 Non- counterbalanced forklift trucks (reach trucks) ................ 18
4. HIERARCHY OF CONTROL ................................................................... 19
4.1 Identify the hazard .......................................................................... 19
4.2 Assess the risk ................................................................................... 19
4.3 Control the risk ................................................................................. 19
4.4 Review and update ........................................................................ 21
5. DUTY OF CARE ..................................................................................... 21
6. ORGANISATIONAL AND WORKPLACE STANDARDS, POLICIES AND
PROCEDURES ........................................................................................... 22
6.1 Work place rules and procedures ................................................. 22
6.2 Working in bad weather ................................................................. 23
6.3 Lightning (electrical storms) ........................................................... 23
6.4 Extreme heat exposure .................................................................. 23
6.6 Unstable ground conditions ........................................................... 25
6.7 Planning for forklift operations ....................................................... 26
7. STABILITY TRIANGLE AND CENTRE OF GRAVITY ................................. 26
Learning Check 2 ................................................................................... 29
8. RATED CAPACITY ................................................................................ 30
9. ATTACHMENTS AND EFFECTS ............................................................. 31
9.1 Common forklift attachments: ...................................................... 31
9.2 Work Box/Personnel work platforms .............................................. 32
9.3 Lifting and suspended loads .......................................................... 34
4
TLILIC0003 Licence to operate a forklift truck Version 3
10. THE MOTOR ........................................................................................ 35
10.1 Internal combustion engine (I.C.E.) ............................................ 35
10.2 Gas cylinders.................................................................................. 36
10.3 Procedure for changing propane (LPG) cylinders ................... 38
10.4 Gas compliance plate ................................................................. 38
10.5 Internal combustion diesel engines ............................................ 39
10.6 Electric forklifts ............................................................................... 39
10.7 Battery changing procedures for electric forklifts. .................... 40
11. FORKLIFTS AND FLAMMABLE LIQUID................................................. 41
Learning Check 3 ................................................................................... 41
12. PRE-OPERATIONAL CHECKS ........................................................... 42
13.1 When raising the load ................................................................... 43
13.2 Travelling ......................................................................................... 44
13.3 Placement of Loads ...................................................................... 45
13.4 Loading trucks ............................................................................... 45
13.5 Loading Pantech’s (large enclosed vans) ................................. 45
13.6 Loading loads with two forklifts.................................................... 45
13.7 Parking ............................................................................................ 46
Learning Check 4 ................................................................................... 47
14. FORKLIFTS AND ELECTRICITY ............................................................ 48
15. FIRST AID ............................................................................................ 50
16. COMMUNICATIONS .......................................................................... 51
17. TRAFFIC WARNING SYSTEMS ............................................................. 51
18. TRAFFIC MANAGEMENT PLANS ........................................................ 52
19. GENERAL SAFETY RULES .................................................................... 53
20. LOAD CENTRE DISTANCE .................................................................. 54
21. CALCULATIONS ................................................................................. 55
Learning Check 5 ................................................................................... 55
22. PRE-ASSESSMENT CHECK .................................................................. 58
23. ASSESSMENT ...................................................................................... 64
5
TLILIC0003 Licence to operate a forklift truck Version 3
INTRODUCTION
What is the Civil Construction Industry?
Australia’s national prosperity is dependent on functional, efficient and cost effective
civil infrastructure. Healthy, well-functioning and productive countries depend on
infrastructure that civil contractors construct and maintain, whether this is in moving
freight on our roads, shipping our products and resources through our ports or building
communities where people live and work.
Transport and utilities infrastructure, construction and maintenance includes, roads,
bridges, marine structures, dams, cable and pipelines, tunnels and site works for
commercial, industrial and housing development.
Civil contractors play a prime role in working with both public sector and private
clients in infrastructure delivery.
This is the business of civil construction.
What is the Civil Contractors Federation?
The Civil Contractors Federation or CCF is Australia’s largest representative body of
the civil construction industry which is responsible for the delivery of Australia’s
infrastructure needs such as roads, streets, subdivisions, bridges, airports, water,
sewerage, drainage and telecommunications.
The Civil Contractors Federation is a nation-wide federation of civil construction
interests. It has fully representative Branches established in all States and Territories of
Australia and a membership base of over 2,000 contracting and industry linked
companies.
Under its banner of Constructing Australia’s Infrastructure, the Civil Contractors
Federation is charged with ensuring the industry is well placed to respond to a fast
changing and challenging external environment. This responsibility extends from
assisting the industry in the planning, delivery and management of the nation’s
infrastructure assets through to the development and retention of a skilled workforce.
Civil Train is the training arm of the Civil Contractors Federation.
6
TLILIC0003 Licence to operate a forklift truck Version 3
Personal Requirements
To be successful in this occupation you should:
• Enjoy practical and manual work
• Be physically fit
• Enjoy working outdoors
• Have good communications skills
• Be able to work in a team environment
• Be alert and observant
• Be willing to keep up with modern developments in civil construction.
How will I be assessed?
You will be assessed on evidence that you can perform the work to industry standards
collected from a range of activities including:
• Completion of all workbook activities
• Theory (knowledge) assessment (closed book)
• Calculations assessment
• Performance assessment
Resources
You will be provided with the following resources:
• Learning Materials workbook
• Knowledge and performance assessments
• Log book or work diary (as required)
Your trainer or employer will provide access to the following documents as required:
• State or Territory Workplace Health and Safety Act
• State or Territory Workplace Health and Safety Regulations
• Relevant standards
• Relevant operations quality documentation.
7
TLILIC0003 Licence to operate a forklift truck Version 3
Legislative Requirements
Like all aspects of modern work, you will be subject to and have to know legislative
requirements such as safety, workplace relations and environmental protection.
These will be explained when you learn the various tasks which make up this unit.
Personal Protective Equipment (PPE)
Your State or Territory workplace safety legislation designates that you must use PPE
as supplied and trained. Correct PPE may include:
• Safety boots
• Safety helmet
• Safety vest (reflective at night) or high visibility clothing
• Safety glasses
• Safety gloves
• Ear muffs or plugs
• Close fitting clothing
• Wet weather gear
• Respirator and filter mask
• Hat
• Sunscreen (SPF 30+)
Assistance with Learning
If at any time while studying this unit you experience learning difficulties or require
assistance and advice, you can get support by contacting your Trainer.
8
TLILIC0003 Licence to operate a forklift truck Version 3
UNIT OF COMPETENCY
1. Plan
work/task 1.1 Task requirements are identified from work orders or equivalent and confirmed with relevant
people and site inspection is conducted in accordance with workplace procedures
1.2 Work area operating surface is assessed to determine suitability for operational use of forklift
truck in accordance with workplace procedure
1.3 Suitability of forklift truck and attachment working load limit (WLL) is determined for the load/s
and work/task requirements in accordance with manufacturer requirements and workplace
procedures
1.4 Working area is inspected and appropriate paths for operating the forklift truck and moving and
placing load/s in work area are assessed and managed in accordance with workplace procedures
1.5 Hazard and risk control measures are identified and reported to relevant person/s in accordance
with workplace procedures
1.6 Traffic management plan implementation is confirmed in accordance with workplace procedures
1.7 Appropriate communication procedures are identified with relevant people in accordance with
workplace procedures
1.8 All work is confirmed to ensure coverage of work/task requirements for the relevant work area is
in accordance with workplace procedures
2. Prepare
for
work/task
2.1 Consultation with workplace person/s is maintained to ensure workplan is clear and consistent
with site requirements in accordance with safe work procedures
2.2 Weather and work environmental conditions are assessed to determine any impact on forklift
truck operations in accordance with manufacturer requirements and safe work procedures
2.3 Risk control measures for hazards identified are checked for implementation in accordance with
safe work procedures
2.4 Forklift truck is accessed in a safe manner in accordance with manufacturer requirements and
workplace procedures
2.5 Forklift truck logbook is checked in accordance with manufacturer, regulatory requirements and
safe work procedures
2.6 Pre-start checks are carried out and any damage and defects are reported, recorded and
appropriate action is taken in accordance with safe work procedures and manufacturer
requirements
2.7 Forklift truck is set up correctly with any relevant attachments as per work plan in accordance
with relevant manufacturer requirements including data plate and safe work procedures
2.8 Operational checks are carried out and any damage and defects are reported, recorded and
appropriate action is taken in accordance with manufacturer requirements and safe work
procedures
2.9 Hazard and risk control measures are checked for implementation and communicated to people in
the work area in accordance with safe work procedures
3. Perform
work/task
3.1 Weight and positioning of load is assessed to ensure compliance with forklift truck data plate
requirements and in accordance with safe work procedures
3.2 Forklift truck is operated safely in accordance with manufacturer requirements and safe work
procedures
3.3 Loads are monitored constantly when lifting, moving, lowering and placing to ensure stability of
load and avoidance of hazards in accordance with safe work procedures
3.4 Unplanned and unsafe situations are responded to in accordance with safe work procedures
3.5 Loads are picked up, transported and placed using all forklift truck movements in accordance
with safe work procedures
3.6 Forklift truck is parked, switched off and isolated appropriately in accordance with manufacturer
requirements and safe work procedures
9
TLILIC0003 Licence to operate a forklift truck Version 3
4. Pack Up 4.1 Forklift truck shutdown procedures are carried out in accordance with manufacturer requirements
and safe work procedures
4.2 Forklift truck is secured to prevent unauthorised access/use in accordance with safe work
procedures
Performance Evidence:
Evidence required to demonstrate competence in this unit must be relevant to and satisfy all the requirements of the
elements and performance criteria on at least one occasion and include:
• applying safe operating procedures for a forklift truck including:
o maintaining safe operating speed
o travelling with load lowered to an appropriate height for the terrain, operating surface and
visibility in relation to
direction of travel
• applying relevant forklift truck manufacturer requirements and data plate information and approved
modifications
to attachments fitted are in accordance with manufacturer requirements
• carrying out pre-start checks, including visual inspection which must include:
o battery charge as required by manufacturer requirements
o checking and interpreting data plate/s are relevant to the attachment and the forklift truck
o checking for signs of paint separation and stressed welds indicating potential structural weakness
o document evidence of damage
o engine / mechanical fluid level checks including fuel as required by manufacturer requirements
o ensuring availability of correct forklift truck logbook and updating records as required
o ensuring forklift truck tynes or other attachment/s are securely fitted
o ensuring seat and mirrors are adjusted appropriately and seat belt is functional
o fluid leaks
o lights are working effectively
o safety equipment checks
o signage and labels to ensure they are visible and legible
o wheels and tyres for damage/correct inflation if applicable
• conducting and applying risk and hazard assessment strategies including:
o insufficient lighting
o other specific hazards including dangerous goods
o overhead hazards and fixed structures, roof beams and doorways
o restricted and poorly ventilated areas
o surface suitability based on forklift truck and task requirements
o the risk of collision with people, moving plant and fixed structures
o weather conditions
• complying with Commonwealth, State and Territory Work Health and Safety (WHS)/Occupational Health
and Safety (OHS)/Occupational Safety and Health (OSH) legislation, regulations safe work and workplace
procedures
• conducting operational checks, which must ensure:
o all controls are located, identified and tested for functionality
o all hydraulic functions operated to maximum extension and ensuring attachment (if fitted)
movements and control functions are smooth and comply with operating requirements
o hazard warning systems (e.g. reversing beepers, lights and horns) are functional
o recording and maintaining accurate information relating to forklift truck operations
o safety devices as fitted
o start-up is in accordance with manufacturer requirements
o steering, transmission and brake functions comply with operating requirements
o there are no unusual noises
• confirming and following traffic management plan procedures relevant to their role in the work area
• conducting relevant procedures for refuelling and isolating fuel/power source as per manufacturer
requirements using appropriate PPE
• determining relevant lifting attachment to perform work/task
10
TLILIC0003 Licence to operate a forklift truck Version 3
• determining lift requirements including:
o positioning of unusually balanced/shaped loads
o centre of gravity
o dynamic nature of load
o tyne/attachment positioning
o weight
• ensuring risk control measures within the work area are effective as per workplace procedures
• identifying, isolating and tagging out defective equipment and reporting to authorised person/s
• interpreting and confirming relevant documentation, workplace instructions, safety information,
emergency procedures for the work task and relevant area
• interpreting workplace procedures in relation to various environmental conditions
• maintaining communication with other workplace personnel through using worksite procedures including:
o audible and visual warning devices
o signage
o two-way radio
o verbal instructions
o written instructions
• maintaining three points of contact whilst accessing and egressing forklift truck and ensuring rungs / steps
are free of hazards
• operating and monitoring safe forklift truck operations using minimum 250kg dynamic and non-dynamic
loads that include:
o aligning tynes/attachment to load
o carrying out a lift to 75% of the maximum height
o conducting trial lift to ensure forklift truck and load are stable, and load is safe to move
o correctly using horns and mirrors in workplace
o correctly positioning and using an observer to assist when operating with a load that may restrict
vision or be placed out of vision of the operator
o driving applicable to conditions and moving loads safely
o driving a forklift truck safely with load in forward and reverse, while maintaining visibility
through an obstacle course including:
▪ an 'S' bend with a minimum 90 degrees left and right turn
▪ ensuring load/s remains stable through pick up, transport and placement
▪ forklift truck speed is appropriate to load and surroundings
▪ lowering dynamic and non-dynamic loads to appropriate height for travel in forward and
reverse
o picking up, driving, manoeuvring and placing dynamic and non-dynamic loads safely at various
heights within a compliant racking system
o picking up, driving, manoeuvring and placing dynamic and non-dynamic loads safely into/onto
an elevated, flat, stable area
o tilting mast (or forks if applicable) to ensure balance of load
o using gluts/dunnage appropriately and lowering load safely
o using tilt and side shift (where fitted) safely to manoeuvre dynamic and non-dynamic loads into
allocated space
• reporting to relevant person/s on site risk control measures that are not in place or are deficient
• setting up an exclusion zone
• securely parking forklift truck and isolating in appropriate position including:
o minimising possible access by unauthorised person/s
o tynes/attachment lowered to required position in accordance with manufacturer requirements
o park brake applied
o switching off, isolating fuel/power source and removing key according to workplace procedures
• shutting down a forklift truck in accordance with manufacturer requirements and workplace procedures
11
TLILIC0003 Licence to operate a forklift truck Version 3
Knowledge Evidence
Evidence required to demonstrate competence in this unit must be relevant to and satisfy all of the requirements of
the elements and performance criteria and include knowledge of:
• Australian and industry standards, codes of practice and guidelines to safely operate a forklift truck
• communication procedures including:
o audible and visual warning devices
o hand signals
o questioning techniques
o signage
o traffic warning systems
o two-way radio
o written instructions
• forklift truck characteristics and capabilities, manufacturer requirements and instructions for any
attachments
• impact of the following on the operation of the forklift truck including:
o failure/loss of control including brakes and steering
o failure of equipment during forklift truck operations
o forklift truck instability causes including:
▪ deterioration of ground condition
▪ overloading
▪ pick up and placement of load
▪ irregular loads
o operating on ramps and uneven surfaces and in restricted spaces
o use of forklift truck data plate and attachment data plate and appropriate methodology to
determine weight of a load is appropriate for forklift truck and any attachment if fitted including
the estimation or determination from:
▪ labels on the actual load
▪ markings on the actual load
▪ paperwork such as consignment notes, running sheets and weighbridge dockets
▪ weighing a carton and calculating load
• manufacturer requirements, instructions and operator's manual
• problems, and appropriate response procedures to unplanned and/or unsafe environmental conditions
including:
o wind
o lightning
o water/ice impacted surface/ground
o rain
o extreme heat
o Ultra violet (UV) exposure
• problems and equipment faults, and implementing appropriate response procedures to unplanned and/or
unsafe situations including:
o lock out and tag out procedures
• relevant procedures for refuelling and recharging forklift truck using appropriate PPE including:
o gas bottle
o connecting battery to charger and disconnecting battery from charger and reconnecting to forklift
truck
o refuelling
• procedures for recording, reporting and maintaining workplace records and information
• risk assessment process including hierarchy of control:
o elimination
o substitution
o isolation
o engineering controls
o administrative controls
o personal protective equipment (PPE)
12
TLILIC0003 Licence to operate a forklift truck Version 3
• safe use and compliance of different types of attachments including:
o bale clamps
o carpet spike for carpet rolls
o drum carrier
o jib attachment
o paper roll clamps
o personnel work platforms
o rotators
o slippers/fork extensions on tynes
• suitability and lifting capability of the attachment to be used
• shut down procedures for a forklift truck in accordance with manufacturer requirements
• traffic management plan procedures and requirements
• typical routine problems encountered operating a forklift truck and associated equipment, and adjustments
required for correction
• workplace procedures including work plan which may be verbal, documented/written, or electronically
generated
• work area operating surface suitability including issues with:
o backfilled ground
o bitumen (damaged, cracked)
o concrete (damaged, cracked)
o hard compacted soil
o potholes
o railway tracks
o rough uneven or difficult terrain including sloping surfaces, uneven surfaces, steel decks and
grates
o soft soils
o trench covers
• Work Health and Safety (WHS)/Occupational Health and Safety (OHS)/Occupational Safety and Health
(OSH) requirements, safe work and workplace procedures
13
TLILIC0003 Licence to operate a forklift truck Version 3
1. APPLYING FOR A HIGH RISK WORK LICENCE (HRWL)
A High Risk Work Licence is a small plastic card with photo identification (similar to a driver’s
licence) with a list of all the classes of high risk work that the holder is authorised to perform.
SOUTH AUSTRALIA
In South Australia, High Risk Work (HRW) is regulated by SafeWork SA.
Each applicant must be aged 18 years or older to obtain a HRW licence.
Some of the responsibilities that apply to HRW applicants under the WHS legislation are to:
• Provide name, evidence of identity and photograph with application for HRW licence
• Provide a copy of certificate that they have successfully completed the unit of
competency relevant to the class of HRWL being applied for
• Not give false or misleading information
• Declare that they do not hold an equivalent licence issued by another WHS regulator
• Declare whether they have been found guilty of an offence under the WHS law
anywhere in Australia
• Declare if they have ever had a HRW licence cancelled, suspended or refused.
According to the WHS Regulations, a person is considered under training for a HRW licence
when:
o They are enrolled in a course of HRW training AND
o Being supervised at a workplace by a person with a current HRW licence for the work
An employer cannot allow a person to perform HRW if they know they are not fully competent
to do so (unless the person is enrolled in a course of HRW training and is supervised at the
workplace by a person with a current HRWL for that work).
After training, applicants will need to prove their knowledge by way of theoretical assessments
and prove their operational skills by way of a performance assessment.
After training and assessment, applicants deemed to be ‘Not Yet Competent’ must wait a
mandatory seven (7) days before being reassessed for the same class of licence.
‘Competent’ applicants will be issued with a Statement of Attainment and a temporary Notice
of Satisfactory Assessment (NSA) which is only valid for a period of sixty (60) days for the
purpose of making an application for a HRW licence. This needs to be taken, with the tax
invoice provided by the assessor, to Service SA or an Australia Post Photo Capture Centre for
processing with the stated fee and 100 points of ID. The new High Risk Work Licence will then
be processed and posted to the applicant.
A HRW Licence requires renewal every five years.
If a HRW licence holder becomes no longer competent to do the work they hold the licence
for, they must:
• NOT perform the HRW AND
• Retrain to become fully competent OR
• Return the HRW licence to the regulator.
When undertaking High Risk Work, the HRW licence holder must take reasonable care and not
adversely affect the health and safety of other persons whilst performing the HRW.
14
TLILIC0003 Licence to operate a forklift truck Version 3
If a HRW licence holder fails to exercise proper diligence when performing HRW they can be
penalised under the WHS Regulations by:
• Having their licence suspended or cancelled or
• If the matter arises at renewal, the regulator refusing to issue the new licence
NORTHERN TERRITORY
In the Northern Territory, HRW is regulated by NT WorkSafe.
Each applicant must be aged 18 years or older to obtain a HRW licence.
You can only conduct High Risk Work if you do not hold a HRW licence when you are:
• Enrolled in a registered training organisation course of HRW training to be able to
apply for the relevant High Risk Work class AND
• Being supervised at a workplace by a person with a licence for the relevant High Risk
Work class
Before you can carry out High Risk Work you must show the employer written evidence that:
- You hold the relevant High Risk Work Licence OR
- That you are undertaking a registered training organization coursed of High Risk Work
training
It is the legal duty of a HRW Licence holder to take reasonable care of their own health and
safety and ensure that their acts or omissions do not adversely affect the health and safety of
others.
If a HRW licence holder fails to work safely when performing HRW in their licence class, NT
WorkSafe can:
• Suspend their licence
• Cancel their licence
• Refuse to renew their licence if the matter arises at licence renewal
• Direct the licence holder to obtain a reassessment to determine competency
A High Risk Work Licence requires renewal every five years.
If a person does not renew their HRW licence within twelve (12) months of the date of expiry
date:
• The HRW licence cannot be renewed
• The person will need to complete a registered training organsiation course of training
to be able to apply for a new HRWL
• If continuing to undertake High Risk Work, the person must enrol in a registered training
origination’s course of training AND be supervised at work by a person with a licence
for that class of HRW.
Once you have successfully completed your training you will be issued with a Statement of
Attainment from the RTO. The assessor will also provide you with a completed HRWL
application which you need to take (with the licence fee and supporting documents) to the
Territory Business Centre. Note, you have to apply for your HRW licence within sixty (60) days
of completing the assessment.
15
TLILIC0003 Licence to operate a forklift truck Version 3
Learning Check 1
1. What is the renewal period for a High Risk Work Licence?
2. Within what time frame must you apply for your High Risk Work Licence after being
deemed competent?
3. Under what circumstance can someone conduct High Risk Work without a High Risk
Licence?
4. What is the legal duty/responsibility of someone undertaking High Risk Work?
5. List 2 ways a HRW Licence holder may be penalised for failing to work safely?
a)
b)
6. SA trainees - What are three things you are responsible for when applying for your
HRW licence? (responsibilities of a HRW applicant)
a)
b)
c)
16
TLILIC0003 Licence to operate a forklift truck Version 3
2. INTRODUCTION
2.1 Legislation, Regulations and Codes of Practice
Regulations are rules that provide details on how to meet the minimum requirements
set by the legislation. Regulations require that employees carrying out work which is
identified as being hazardous are required to be trained to operate in a competent
manner.
This training program has been designed to examine the hazards associated with
working with forklift trucks and initiate safe work procedures so as to eliminate unsafe
work practices in accordance with:
• The National Occupational Health and Safety Certification Standard for Users
and Operators of Industrial Equipment [NOHSC:1006(1995)],
• The Work Health and Safety Act (WHS) 2012 (SA)
• The Work Health and Safety Regulations 2012 (SA)
• (National Uniform Legislation) Work Health and Safety Act and Regulations
2011(NT)
• The National Standard for Licensing Persons Performing High Risk Work 2006
• The Construction Work Code of Practice may be relevant dependent upon
the working environment
2.2 Organisational and workplace standards
Safe systems of work are the total set of methods adopted for carrying out the
operations required in a particular workplace. They cover all aspects of the
employment situation, including site specific rules and regulations, safety and
emergency procedures, the organisation of work processes, the methods of using
machinery, plant and equipment and training and instruction about associated
hazards and their management.
We will examine aspects of operation which include:
• pre-operational checks
• post start operational checks
• why and how to plan work
• machine selection
• set-up and shut down procedures
• hazard identification and hazard control
• Fault finding and recording procedures
• Log book, specifics entry
17
TLILIC0003 Licence to operate a forklift truck Version 3
3. THE FORKLIFT TRUCK
Forklift trucks transport and stack materials. They are a short wheel based truck with a
vertical mast.
There are two types; counterbalanced and non-counterbalanced forklift trucks.
The LF (forklift) licence entitles an operator to use both machines.
3.1 Counterbalanced forklift trucks
Counterbalanced forklifts use the front wheel axle in the same way as the
fulcrum of a lever. The load is counterbalanced on one side by the weight of
the machine on the other side.
All the weight behind the point of balance (fulcrum) acts as a counterweight.
18
TLILIC0003 Licence to operate a forklift truck Version 3
3.2 Non- counterbalanced forklift trucks (reach trucks)
In non-counterbalanced forklift trucks, the centre of the load is behind the
fulcrum point. They are known as ‘reach’ or ‘straddle’ trucks.
This type of forklift reaches out to deposit the load or straddles the stack for
depositing the load. They should not carry loads unless the reach is retracted.
They are used for particular load stacking functions and are more versatile than
the counterbalanced type in warehouse locations.
19
TLILIC0003 Licence to operate a forklift truck Version 3
4. HIERARCHY OF CONTROL
The purpose of a risk assessment is to reduce or eliminate the potential for injury to
personnel whilst at work.
This is a systematic method of identifying, assessing, and reducing hazards.
To complete a risk assessment correctly we need to:
4.1 Identify the hazard
Always consider the task to determine whether there is any risk of a person injuring
themselves or others when carrying out the work.
4.2 Assess the risk
How likely could an injury occur?
How often will we be exposed?
What injuries could occur e.g. grazes, bruising, broken leg, fatality etc.?
4.3 Control the risk
What control(s) could be put in place to reduce or eliminate the incident occurring?
HAZARD CONTROLS MUST BE APPLIED PRIOR TO OPERATING THE FORKLIFT
20
TLILIC0003 Licence to operate a forklift truck Version 3
Control the Risk with the use of Hierarchy of Control:
The Hierarchy of Control is a six step approach to controlling hazards in the
workplace. Elimination is always the preferred option but not always possible.
ELIMINATION
Wherever possible the hazardous item or substance or work practice should be
removed.
For example: noisy grinding or cutting, purchase pre-cut materials.
SUBSTITUTION
Replace the hazardous system or process with one that presents less risk.
For example: lift smaller packages, use a less toxic chemical, vacuum in place of
sweeping.
ISOLATION
Place the hazardous system or process in a separate area where the exposure is
reduced.
For example: place barriers around a spill until cleaned up, place heat producing
objects in separate well vented rooms.
ENGINEERING
Structural changes to the work area, or process that forms additional protective
barriers between hazards and workers.
For example: provide a trolley to move heavy loads or surround moving parts with a
guard.
ADMINISTRATION
Reduce exposure to hazards via procedures, instructions and training.
For example: job rotation, shorter shifts, maintenance programs, instruction and
training.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
Where workers are exposed to hazard and other measures have proven ineffective
or non-viable. The last line of defense relies on correctly selected, fitted and
maintained PPE.
For example: provide hearing and eye protection, gloves, sun cream, masks etc.
until a more suitable solution can be found.
21
TLILIC0003 Licence to operate a forklift truck Version 3
4.4 Review and update
During a job, things may change which require the risk assessment to be reviewed
e.g. weather changes, additional work needed, changes in the work group etc. We
must ensure that the risk assessment is still current and valid by identifying the changes
and reviewing the risk assessment.
5. DUTY OF CARE
Your duty of care or due diligence means you must take reasonable care to ensure
that you and others are not harmed by your actions or omissions. This applies to
employers and employees.
Score Level of Risk Urgency of Action Needed
18 to 25 High Immediate action required
10 to 17 Significant Senior management attention needed
urgently
6 to 9 Moderate Management responsibility must be
specified and actioned
1 to 5 Low Manage by routine procedures
Impact/Consequences
Likelihood Insignificant Minor Moderate Major Catastrophic
Almost
certain
10 16 20 23 25
Likely 7 11 17 21 24
Possible 4 8 12 18 22
Unlikely 2 5 9 14 19
Rare 1 3 6 13 15
22
TLILIC0003 Licence to operate a forklift truck Version 3
6. ORGANISATIONAL AND WORKPLACE STANDARDS,
POLICIES AND PROCEDURES
Each workplace has conditions that can contribute to dangerous situations.
Operators should inspect the workplace for any potential hazards and consult with a
supervisor, site engineer, OHS rep or leading hand to ensure the hazard has been
eliminated or minimised before starting work/ operating the forklift. On some sites it
may be necessary to obtain a work permit to operate a forklift as a safety control
measure.
6.1 Work place rules and procedures
By notifying the appropriate people we can access the correct information needed
to instigate our own safe work procedures and become aware of the particular rules
and procedures that affect the site we are on.
Each work site or organisation will have its own policies and procedures as to how it
will work to meet legislative and regulatory requirements. Take time to ensure you
have access to these and that you understand the processes. Remember, policies
and procedures need to be reviewed regularly to ensure they are current, relevant
and compliant.
Be aware of the following HAZARDS:
• Blind spots - (corners, alleyways with cross traffic, the mast or load)
• Surrounding structures - (buildings, ceiling clearance, i.e low pipes etc)
• Doorway clearances
• Pedestrians
• Other vehicles - (Mobile plant and equipment)
• Obstructions
• Unsafe environmental conditions - (Extreme heat, Ultra violet (UV))
• The road surfaces - (deteriorated, damaged)
• The fumes produced by the forklift
• Dangerous materials - (load is flammable, combustible and explosive)
• Overhead Services
• Underground Services - (pit covers)
• Electric Lines/cables Power sources
• sloping ground and ramps
• Bad weather conditions - (wind, lightning, ice)
• Unsuitable ground conditions
23
TLILIC0003 Licence to operate a forklift truck Version 3
6.2 Working in bad weather
If you work outside, you’re at risk of exposure to bad weather conditions including
storms, wind, rain, and lightning. Your workplace must have measures in place to
manage the risks to your health and safety caused by bad weather, including:
• working indoors (where possible)
• postponing outside work
• providing access to shelter
• securing structures and objects and turning power off, and
• providing protective equipment, like eye protection.
Eliminating exposure to bad weather is the best protection.
6.3 Lightning (electrical storms) Lightning (electrical storms) are one of nature's most spectacular displays, but they
can also have catastrophic consequences — triggering fires, destroying buildings,
disrupting air traffic and in the worst-case scenario, causing death.
It is estimated that there are five (5) to ten (10) deaths a year from lightning strikes in
Australia and more than 100 people are seriously injured annually.
Recommended precautions to be taken if working outdoors during a thunderstorm
include:
• Seek shelter immediately in an enclosed car or substantial building;
• Never shelter under trees because your body is a better conductor of electricity
than the tree;
• If boating or engaged in other aquatic activities, head for shore straight away;
• Avoid touching, handling and proximity to any metallic objects that may
become part of the discharge path, for example towers, the metal parts of
vehicles or mobile plant, power lines, pipes and rails;
• Do not handle fishing rods, umbrellas, golf clubs or any other metal objects and
stay clear of sheet metal, wire fences, clotheslines and so on; and
• If caught in the open, crouch down with your feet together. Do not lie down –
the idea is to be as low as possible, but with minimal contact with the ground.
• In addition, using wired electrical equipment, hand-held tools, appliances or
landline telephones should also be avoided during thunderstorms.
6.4 Extreme heat exposure
Extreme Heat or a Heatwave is when there are three or more days of unusually high
maximum and minimum temperatures. Extreme heat is more than just ‘hotter than
usual’ weather.
When temperatures are hotter than 35°C, your body may not be able to cool you
down enough for you to stay healthy, especially if you are an older person or if you
are taking certain medicines.
In extreme heat, you are more likely to develop a heat-related illness and become
unwell much faster than you would when in warm or hot weather.
24
TLILIC0003 Licence to operate a forklift truck Version 3
Everyone is at risk of heat-related illness, here are simple steps that may assist to stay
healthy in the heat:
• Drink plenty of water
• Stay cool with a fan or air-conditioner
• Avoid going out in the hottest part of the day
• Keep curtains, blinds and windows closed during the day to keep your home
cool
• Cool off with a shower or bath
• Look out for family, friends and the elderly
• Check the weather forecast so you know when hot weather is coming
• If you go outside during the day, wear loose-fitting, long-sleeved and light-
coloured clothing, a hat, sunglasses and SPF30+ sunscreen.
6.5 Ultra violet (UV) exposure
Ultraviolet (UV) radiation is a type of energy produced by the sun and some artificial
sources, such as solariums.
UV radiation isn’t like the sun’s light or heat, which we can see and feel. Your senses
cannot detect UV radiation, so you won’t notice the damage until it has been done.
Sun exposure is well established as the major cause of skin cancer in Australia. It is
the ultraviolet (UV) radiation component of sunlight which is harmful; and the level of
UV radiation is not directly related to temperature or brightness of sunlight.
This means that harm can still occur on cool or cloudy days during the peak UV
periods of the year. Exposure to UV Index levels of 3 or above can contribute to skin
cancer. (The UV index is a measure of UV radiation and the higher the index value
the greater the potential for damage to skin. In addition to skin cancer, solar UV
exposure is a major cause of eye damage including photoconjunctivitis and
photokeratitis, cataracts and pterygia. UV damage also causes sunburn, tanning,
and premature ageing.
Here are simple steps that may assist to avoid over exposure to UV radiation:
• Work in shaded areas or temporary shade where possible
• move jobs where possible to shaded areas
• consider applying window tinting to work vehicles
• modify reflective surfaces where possible
• uterlise indoor areas or shaded outdoor areas for rest/meal breaks
• schedule outdoor work tasks to occur when levels of solar UVR are less
intense, such as earlier in the morning or later in the afternoon
• schedule indoor/shaded work tasks to occur when levels of solar UVR are
strongest, such as the middle part of the day
• rotate between indoor/shaded and outdoor tasks to avoid exposing any one
individual
25
TLILIC0003 Licence to operate a forklift truck Version 3
• use of appropriate sun protective PPE in line with SunSmart guidelines
including:
o sun protective work clothing
o sun protective hats
o sunglasses
o sunscreen
6.6 Unstable ground conditions
Ensuring there is adequate ground stability to support the load is a fundamental step
in planning for mobile plant use. Procedures for ensuring that plant does not
collapse into the ground or tip over are well documented in manufacturers’
instructions. Ground conditions can vary dramatically from one workplace to
another and from one part of the workplace to another. Failure to address poor
ground conditions (ground bearing pressures/potential non-weight bearing
surfaces) to ensure mobile plant stability can lead to the plant overturning, with
serious injury or death to the plant operator and others nearby.
Unstable ground conditions relate to: • Rough terrain – unstable driving and load could become unstable
• Soft soils – as forklift can sink and become unbalanced
• Backfilled ground – may not be compacted properly to hold forklift weight and
equipment can sink and become unbalanced
• Deterioration of ground conditions
o Damaged and or cracked bitumen – rough, unstable and possible raised
material
o Damaged and or cracked concrete – rough, unstable, possible raised
material and possible of exposed steel/reinforcement.
• Hard compacted ground – IF not managed and continually monitored, as the
operations can dry out soil and it can break-up, crumble and turn to powder/dust.
With eminent weather (rain) it can could become soft, this includes operations
nearby that uterlise large amounts of water. May have crust on its surface, but the
ground underneath could be soft and unstable.
• Steel decks, grates and trench covers – not designed to withstand forklift weight
and could fall through.
• Railway Tracks - incoming trains, getting stuck or snagged on the line and rail
ballast (loose large aggregate). Ensure appropriate permits and authorisation is
obtained, especially working inside the rail corridor. When parking and leaving
unattended ensure the forklift is at least three metres away from rail line.
26
TLILIC0003 Licence to operate a forklift truck Version 3
6.7 Planning for forklift operations
Other than hazards you must plan before you operate. This
includes considering Non-Site related hazards that will have an
impact on your operations, such as but not limited to:
• Load characteristics (weight, height)
• Rated capacity of the plant you are using
• Availability of the plant
• Communications (Safe and adequate – i.e. UHF Radio
• Permits required for your task
• Equipment required for the task (Signs, Barriers, PPE and additional tools)
• Specifics of the task (timeframes, location)
7. STABILITY TRIANGLE AND CENTRE OF GRAVITY
Forklifts have 3-point suspension formed from the front drive axle (a and b) and the
centre of the rear axles (c) and are unstable by design.
All objects have a natural centre of gravity (C.O.G), as do forklifts. The centre of
gravity on a forklift can change position pending the load you are carrying, the way
you drive and other varying factors. If the centre of gravity shifts outside the safe
working area, known as the Stability Triangle, the forklift will most likely tip over, either
sideways (laterally) or forwards (longitudinally).
Forklifts have no suspension but three contact points which form the stability triangle.
The two rear wheels are attached in the centre of the rear axle via a pivoting pin. This
pin allows the rear axle to rock up and down to allow movement over uneven
surfaces. This can affect the lateral (sideways) stability of the machine. All forklifts
have a high centre of gravity (C. O. G) and a narrow wheel base, which adds to their
lateral instability.
27
TLILIC0003 Licence to operate a forklift truck Version 3
Note the change in the centre of gravity in the following diagrams.
Be aware of the factors listed below which can affect lateral instability or sideways
tipping:
• Turning at speed
• Turning with an elevated load
• Driving over uneven surfaces
• An unevenly distributed load
• Driving with a flat or underinflated tyre
• Turning on an incline
• Travelling with the load raised
• Braking too hard when turning
• Side shift not centred
• Lifting a load on one fork arm
• Driving sideways across a slope
28
TLILIC0003 Licence to operate a forklift truck Version 3
The front wheels of the forklift act as a fulcrum, with the forks on one side and the
machine body on the other. If the weight at the fork ends is heavier than the
counterweight it will cause longitudinal instability (the fork will tip up).
Be aware of the factors listed below which can affect longitudinal instability or
forward tipping:
• Overloading
• Increasing load centre distance
• Severe braking
• Load not positioned against the heel of the fork arms
• Lifting a load with the mast tilted forward
• Driving with reach extended
• Travelling with the wrong way up or down a ramp
• Uneven loads, forward
• Rapid reversing with heavy loads
• Jerky hydraulic control movements
29
TLILIC0003 Licence to operate a forklift truck Version 3
Learning Check 2
1. What is the lowest level of control measure on the hierarchy of control?
……………………………………………………………………………………………………………
2. Name two things that can affect longitudinal (forward) instability:
i) ………………………………………………………………………………………………
ii) ………………………………………………………………………………………………
3. Name two things that can affect lateral (sideways) instability:
i) ………………………………………………………………………………………………
ii) ………………………………………………………………………………………………
4. Name 2 hazards and their control measures when operating a forklift:
i) ………………………………………………………………………………………………
ii) ………………………………………………………………………………………………
30
TLILIC0003 Licence to operate a forklift truck Version 3
8. RATED CAPACITY
Operators must know a forklift’s rated capacity. It can be found on the vehicles Data
Plate and comprises the maximum lifting weight, height and load centre distance of
that vehicle. These three elements combine together to form rated capacity and
determine what the forklift can lift. Each of these elements may be affected by
altering another.
Rated capacity = maximum load that a forklift truck is designed to carry at a load
height and specified load centre distance shown on load chart/data plate.
On this data plate: Max load 1400kg at 4310mm height with a 600mm load centre
The data plate is usually found next to the driver’s seat. If attachments are fitted a
separate load rating notice needs to be displayed. To prevent accidents, the
weight of the load needs to be checked against the specifications of the forklift.
Methods of determining load weights may include;
• Weighing individual items then adding the totals together,
• Checking the load for attached labels
• Asking to see con-notes, manifests, invoices, delivery dockets etc.
Rated capacity must not be exceeded.
Operators must be able to read and understand the data plate and the conditions
of loading at all times.
It is the responsibility of the forklift owner to provide a data plate on each vehicle that
displays the lifting capacity of the machine under all lifting conditions. It is illegal to
use a forklift without a data plate or one that is illegible.
Do not use a forklift that does not have a load or data plate.
31
TLILIC0003 Licence to operate a forklift truck Version 3
9. ATTACHMENTS AND EFFECTS
Attachments are working aids that are added to a forklift for certain tasks. Some are
permanently attached and hydraulically powered while others are only attached
when required and removed afterwards.
All attachments add weight to a forklift and can therefore affect the stability and
reduce the safe working (SWL) of a forklift.
Make sure all attachments are suitable for load and forklift and have their own data
plate before use.
They must be attached securely to forks with chains and/or pins if removable.
Do not rotate the load while moving if a load rotator mechanism is fitted.
Make sure the forklift data plate allows the attachment to be used on that forklift.
The use of any attachment will reduce the lifting capacity of all forklifts.
If asked to use an attachment you are unfamiliar with, ask for training or advice from
a competent person first.
In all cases, the forklift must be approved to use attachments. Safe working loads will
be stamped on the data plate for each approved attachment.
9.1 Common forklift attachments:
The number of forklift attachments that are available today has increased over the
years and their quality has improved as well, mainly because they offer businesses a
great deal more functionality and added features.
Side Shifters are one of the most common attachments used today; most forklifts
come with this attachment as standard. This attachment allows you to shift the forks
(tynes) from side to side allowing for small adjustments to be made by the operator;
enabling alignment with pallets without manoeuvring the entire forklift.
This handy attachment allows:
• Movement of loads in tight spaces without
moving the whole truck
• Precision of movement with loads
• Accurate alignment with pallets
• Reduced damage to pallets, loads and
racking
32
TLILIC0003 Licence to operate a forklift truck Version 3
It’s important to note though that when you have to attach a side shifter to a forklift,
this will reduce the overall load capacity of the truck because:
• The tool ads weight to
the equipment
• The load centre is
shifted outward
If you have just picked up a load using side shift you should centre the side shift
before travelling with the load to maintain the stability of the load and forklift.
Other attachments include:
9.2 Work Box/Personnel work platforms
Some industrial lift trucks are designed to lift people. For example, an ‘order-picking
industrial lift truck’ has an elevating platform that allows the operator to load shelves
as well as control platform height and steer the industrial lift truck. If you use a
separate work platform or box fitted to an industrial lift truck to lift people then you
must ensure people in a work box:
• are securely attached
• stay largely within the workbox
• wear a safety harness if there is a risk of falling from a height, and
33
TLILIC0003 Licence to operate a forklift truck Version 3
• can safely exit from the workbox and the industrial lift truck in the event of a
failure in its normal operation.
Forklift trucks may be used to provide a safe work platform (see figure below). Work
platforms and boxes should only be used to raise people performing occasional
tasks and must be securely attached to the industrial lift truck. The industrial lift truck
operator should perform an initial trial lift without a person in the work box to check
the work box has a clear path and will not make contact
with overhead power lines or other overhead obstructions.
The following risk control measures should be put in place when using work platforms
or boxes (safe use):
• The industrial lift truck is to be stabilised at all times while lifting people and
preferably only used on a hard, even and level surface.
• Before work starts make sure the parking brake is set, the vehicle drive
controls are in neutral, the mast is vertical and hydraulic controls are off
except lift and lower.
• Workers are trained to use work boxes safely including emergency
procedures so occupants can be rescued if an incident or breakdown
happens.
• Workers stand on the floor of the work box, not on a ladder or other object.
• Where possible, work boxes are not used to transport people.
• The operator of the industrial lift truck stays at the controls at all times.
• instructions or those of a competent person. Each fall arrest anchorage point
should be located so a lanyard can be attached to it before the person using
the lanyard moves into a position where they could fall. Installed anchorage
points should be tested and approved by manufacturer.
34
TLILIC0003 Licence to operate a forklift truck Version 3
• For compliance and safety:
o Work boxes should only be attached to a compliant industrial lift truck
with a load capacity data plate that says which attachments may be
used.
o The work box safety gate is self-locking and kept shut when in the
raised position.
o Work box fall arrest anchorage points should meet the requirements of
the work box manufacturer’s
o Industrial lift trucks are equipped with flow restrictors or similar i.e. the
valves in the hydraulic lines to prevent free fall in the event of a hose
failure.
9.3 Lifting and suspended loads
You must ensure that the industrial lift truck is equipped with lifting attachments that
are right for the load to be lifted or moved by the truck. The attachment should be
securely connected to the industrial lift truck prior to operation to prevent it
separating from the lifting media. Many specialised attachments are available for
industrial lift trucks including slippers, bin lifters, carpet spikes, jibs, spreaders and
drum handlers (see figure below).
Attachments like jibs have more than one lifting point and the load chart should
show the lifting capacity for each point. If an attachment is fitted to an industrial lift
truck, ensure you have access to information on the de-rated capacity of the
industrial lift truck.
By using the industrial lift truck load chart and the information with the attachment,
often found on the attachment’s load rating plate, the de-rated capacity of the
industrial lift truck can be calculated.
In addition, the Australian standards dictate additional capacity reductions for
forklifts used with suspended loads:
• When a suspended load is carried (i.e. a jib attachment is used) the rated
capacity calculated for the forklift must be reduced by 20%.
35
TLILIC0003 Licence to operate a forklift truck Version 3
• When two forklifts carry the same load, the load applied to each truck shall
not exceed 75% of that truck’s capacity.
Each of the de-ration factors stated here are cumulative. That is, the lifting capacity
at a given load centre is calculated, the self-mass of the jib and slings is subtracted
from this, then the 20% de-ration for suspended loads is applied, then (if two trucks
are used together) the 25% reduction is applied. This may result in a lower than
expected lifting capacity for a forklift.
Holes should not be drilled or cut through attachments or lifting media, for example
fork arms, as this can weaken and destroy the integrity of the attachment. Changes
should not be carried out unless they have been specified by a competent person,
for example a mechanical engineer
10. THE MOTOR
10.1 Internal combustion engine (I.C.E.)
Internal combustion engines are powered by diesel fuel, petrol or LPG or Compressed
natural gas (CNG). An LP gas motor is a petrol motor that has been converted to use
gas instead of petrol.
WARNING: Internal combustion engines produce the odourless, but poisonous gas,
called carbon monoxide. A person working in a confined space where carbon
monoxide is present could become seriously ill or die from inhalation.
Carbon monoxide builds up in the body and can kill in twenty minutes. Make sure
there is adequate ventilation where forklifts with internal combustion engines are
operating.
Do not refuel an internal combustion forklift unless the motor is stopped and the ignition
is turned off. If not, there is a chance of explosion.
Refuelling using a fuel pump/bowser
1. Remove the filler cap. Avoid dust getting into the fuel tank.
2. Ensure the area is well ventilated when fuelling vehicles or equipment.
3. Once started, note the pressure uptake in the fuel hose.
4. Immediately report any leaks that are observed. Turn off pump if required.
5. Keep the metal fill nozzle in contact with the lip of the tank to eliminate any static
accumulation.
6. Adjust the nozzle trigger to suit the particular fuel flow requirements.
7. Always check the fuel flow at regular intervals during normal operation.
8. Never kink the fuel hose to restrict or cut off the flow of fuel.
9. Report any fuel spills immediately and begin use of spill response/ recovery kit.
10. If fuel splashes onto clothing, remove and allow for fuel to evaporate completely
outdoors before washing. Thoroughly wash clothing before re-use
36
TLILIC0003 Licence to operate a forklift truck Version 3
Re-fuelling with a jerry can/fuel container
1. Use a proper fuelling nozzle or funnel to avoid splashing fuel on the engine or frame
of the equipment.
2. Fill slowly and listen to air coming out of the can as the fuel pours in. As the can
nears the full level, air will
come out faster, and the pitch will get higher. Stop before the tank is full. Leave 5
percent empty to allow for expansion of the tank.
3. When the tank is full, let the fuelling nozzle drain for a few seconds before removing
it from the fuel port to
prevent dripping.
4. Replace the filler cap.
10.2 Gas cylinders
Every cylinder must be inspected by an authorised LPG test station at least once every
10 years. The last inspection date should be clearly stamped on the cylinder collar,
neck or footing
If any leakage is detected or suspected from a cylinder, turn it off immediately and
refer to emergency procedures
Gas is a highly volatile explosive. Change gas cylinders in a well-ventilated area, well
clear of a naked flame or a source of ignition. Only
those trained and authorised to do so should
change gas cylinders.
Beware of burns from escaping gas. Always wear
gloves and safety glasses and do not smoke whilst
changing LP gas cylinders.
Test date: 10/17 = Oct 2017
Retest date: Oct 2027 (10 years)
37
TLILIC0003 Licence to operate a forklift truck Version 3
Handle cylinders
carefully Take care when handling cylinders to avoid impact damage.
DO NOT drop cylinders off vehicles or docks when unloading or allow heavy objects
to fall on them.
Impact damage can potentially reduce the cylinder wall thickness, which could lead
to premature cylinder rupture.
Barcodes are to alert the fillers and operators when the cylinders are due for re-test,
and for identification purposes. DO NOT under any circumstances tamper with or
remove these.
Cylinders need to be kept cool
DO NOT store cylinders at temperatures greater than 65°C.
On extremely hot days every effort should be made to keep the cylinders in the shade.
Excessive heat – results in an increase in internal pressure.
Excessive heat can reduce the strength of the cylinder resulting in localised bulging
at the source of the heat and in extreme cases cylinder rupture. Care must be taken
with an oxy-fuel gas torch when in use. DO NOT allow the flame from an oxy-fuel gas
torch or other appliance to point onto cylinders.
Some suppliers like BOC fit a plastic Test Date Tags (TDTs) on the cylinder valve inlet
connection which will distort or melt at a predetermined temperature when heat-
affected. This is to alert BOC (and customers) of any heat damage to the cylinder.
Any heat-affected cylinders are sent to a BOC cylinder test shop to determine if they
are safe to be returned back into gas service or if they are to be scrapped.
38
TLILIC0003 Licence to operate a forklift truck Version 3
10.3 Procedure for changing propane (LPG) cylinders Take the following steps in the order below when changing gas cylinders:
1. Wear eye protection and insulated, loose fitting gloves such as leather (dry)
or insulated neoprene.
2. Close the valve on the cylinder.
3. Run the engine until it stops. This ensures that the connection hose is empty.
4. Shut off the engine.
5. Open the connecting nut and inspect valves for leaking. Do NOT use metal
tools.
6. Disconnect the hose.
7. Disconnect the holding straps.
8. Remove the empty cylinder.
9. Inspect the replacement cylinder for damage.
10. Replace with a full cylinder in the proper position.
11. Connect the holding straps.
12. Tighten the connecting nut (wiggle hose).
13. Open the valve on the cylinder slowly and check for leaks. (can use solution
of soap and water). Smell – listen – look.
14. If the valve leaks:
1st time - Tighten the nut and continue.
2nd time - Change the cylinder.
3rd time - Change the hose.
15. Open the valve fully (slowly).
16. Check that the hose is turned inward.
17. Secure the hose downward.
18. Secure the cylinder.
19. Start the engine and resume operation.
10.4 Gas compliance plate All LPG forklifts must have an installer’s compliance plate.
Certification
On completion of any aftermarket installation work, the owner/hirer of the industrial
equipment will be supplied a certificate of compliance in accordance with
AS/NZS4983:2010 Gas fuel systems of forklifts and Industrial engines, which will also
give an installation date and the serial number(s) of any fixed container(s).
Compliance plates
An LP gas/CNG compliance plate should be securely attached to a permanent
part of the industrial equipment and must be clearly visible.
The compliance plate should take the form
shown in figure (right of page) and all
applicable information should be provided by
the installer. The information must be
permanently inscribed, where applicable,
and clearly legible.
39
TLILIC0003 Licence to operate a forklift truck Version 3
10.5 Internal combustion diesel engines
Most diesel engines must warm up before they can start. When the ignition key is
turned on, the glow plug is activated. This warms up the fuel so it will fire.
There is a delay of several seconds from ignition until the starter motor turns on the
engine. A light on the dashboard indicates that the fuel is warming. It goes out when
the engine is ready to fire.
Try to avoid allowing a diesel engine to run out of fuel. Diesel engines fire on the
compressed vaporised fuel and will not fire if there is air in the fuel lines. If a diesel
engine runs out of fuel, a competent person must bleed the system of air before it can
be restarted.
Diesel engines also emit carbon monoxide gas. A badly tuned diesel engine can emit
more carbon monoxide than a petrol motor. Remember that carbon monoxide is
odourless, will build up and can kill.
10.6 Electric forklifts
Electric forklifts are quieter than I.C.E vehicles so greater care must be taken when
operating as pedestrians are less likely to hear one approaching.
Recharging of electric forklifts must take place in well-ventilated areas as the batteries
produce a poisonous, odourless, flammable gas during the recharge process. This gas
is known as hydrogen and is extremely dangerous when allowed to build up.
Hydrogen is highly explosive and extremely harmful if inhaled.
40
TLILIC0003 Licence to operate a forklift truck Version 3
10.7 Battery changing procedures for electric forklifts.
Battery charging safety precautions:
o Be sure the charger is OFF before connecting or disconnecting the
battery.
o Do not disconnect the battery plug when there is current going through,
as this may cause arcing and damage the plug.
o Battery chargers should be in a well-ventilated area and should be easily
accessible.
o Battery chargers should not be in a wet or damp area, and never stand in
water when connecting battery to charger.
o Always match the correct charger for the battery.
o Do not smoke, use power tools or do anything that will create sparks
around the battery charger area. Charging batteries gives off explosive
flammable gases which easily ignite when coming into contact with a
spark.
o Contact your supervisor if the battery, battery charger cables or
connectors show any bare wires, melting or damage. The connectors
should have a snug fit and should not be damaged from arcing.
o Check to make sure that the power supply cable to the charger is in good
condition.
o Do not touch battery terminals or the cell connectors on top of the battery
to prevent getting an electrical shock.
o Do not place any tools or any other metal objects on top of a battery.
o Equalize batteries on the last day of the week, last shift of the day - to fully
charge battery.
o If you suspect any abnormal battery or charger condition, turn off the
power supply and inform your supervisor immediately.
Battery Charging Procedure:
1. Disconnect the battery from the forklift
2. Check cable and connectors for damage (do not charge if damaged)
3. Check the battery lid is open before charge (dissipate gases during charge)
4. Do not open or remove the vent caps unless topping up (watering battery)
5. Plug the battery into charger
6. Turn on the charger (generally switch on front panel)
7. Take note of any charge indicators signifying start of charge cycle
(lights/voltage needles)
8. Always allow a complete charge cycle (do not interrupt)
9. Check if charge complete (charge indicator)
10. Un-plug battery (do not unplug by pulling cables, use the plug)
11. Check water level
Watering a battery:
o Always water (top up) the battery after charging
o Never over-fill the battery (maximum 10mm above plates)
o Water the battery at least once per week
o Always use clean water (preferably distilled/deionised)
o Xtreme fast charging (XFC) and gel batteries do not require
watering
41
TLILIC0003 Licence to operate a forklift truck Version 3
11. FORKLIFTS AND FLAMMABLE LIQUID
Flammable liquid stores and other areas where flammable liquids are used are
usually zoned as having a ‘hazardous atmosphere’.
Forklifts must be modified or ‘flame proofed’ before they can be used in a hazardous
atmosphere and have a compliance plate to that effect.
‘Flame proofed’ diesel powered forklifts have an exhaust water wash box, which must
be flushed out and refilled every shift.
‘Flame proofed’ battery powered forklifts must not be connected to the battery
charger near to any area where flammable liquids are handled in open containers.
Petrol and LP gas forklifts are never flame proofed because of their spark ignition
system.
Learning Check 3
1. Why should you use an electric machine in a confined space?
....................................................................................................................................................
2. Name three types of forklift motor:
i) ………………………………………………………………………………………………
ii) ………………………………………………………………………………………………
iii) ………………………………………………………………………………………………
42
TLILIC0003 Licence to operate a forklift truck Version 3
12. PRE-OPERATIONAL CHECKS
It is a legal and mandatory requirement that the first person to use the plant on any
given day conducts a pre-operational inspection to ensure not only the operator’s
safety but the safety of those around them.
Here is an example of a standardised pre-operational inspection checklist used for
counterbalanced internal combustion engine (I.C.E.) forklifts.
PRE -
START
CHECKS - Before
you turn
key and
start-up
forklift)
POST-
START
CHECKS – (checking
functional
operations
before you
commence
work.)
43
TLILIC0003 Licence to operate a forklift truck Version 3
13. SAFE OPERATION
Forklift trucks should only be used on hard level surfaces. Four-wheel drive or rough
terrain type should be used on unstable terrain.
13.1 When raising the load
• Carry loads as low as possible at all times, never higher than the front axle.
• Hydraulic controls should be ‘eased in’. If the controls are plugged or pushed
quickly, the operation will be jerky
• Make sure the forks are centred when they are entering a pallet and do not
contact the pallet until you are ready to lift
• Do not enter the pallet with the mast tilt back or forwards (this will bind the
forks). Forks must be level and mast vertical
• The load should always rest against the heel of the fork arms. This will ensure
the load centre is in the right place
• If the load weight is unevenly distributed on the pallet, put the heavy end of
the load against the heel of the fork arms
• Make sure the forks are centred on either side of the mast if side shift is attached
or side tipping may occur
• A properly constructed hardwood pallet weighs 35kg and has a SWL of 2000kg.
Do not overload pallets
• Do not move damaged pallets. Loads should be repacked to undamaged
pallets wherever possible
• Do not allow more than a third of the top section of an unwrapped load to
stand above the top of the load backrest extension. A load not backed by
the load backrest can fall back and tangle with the mast, or if the load is very
high, can topple back onto the driver
• Unsafely or unevenly packed pallets should be repacked.
• Do not raise a load with just one fork as this can destabilise the forklift and the
load or cause damage to the lifting mechanism.
• Always raise the load before tilting the load backwards
44
TLILIC0003 Licence to operate a forklift truck Version 3
13.2 Travelling
• Always travel with the load tilted backwards and close to the ground
• Never travel with the load or the forks above front axle height
• Forklifts are one-person vehicles. Do not carry a passenger unless specified as
acceptable by the manufacturer and displayed on the data plate
• You can only lift people in an approved work platform
• Understand your site’s traffic requirements
• Reduce speed and proceed with caution on wet or greasy surfaces
• Do not attempt to turn a forklift when it is on a sloping surface (this could affect
lateral stability and cause it to tip over sideways)
• Always drive up and down inclines slowly (check manufacturers specifications
for any special features that the forklift you are operating has for operating up
and down hills)
• Face the load uphill when travelling up a slope
• Face the load uphill and look behind you when reversing down a slope
• Have someone guide you when driving up a hill with a bulky load that blocks
clear vision
• Before reversing check over both shoulders, check mirrors (if fitted) check path
is clear
• Blow the horn and drive slowly when approaching a blind corner
• Make sure that no one is in the way or standing next to you before driving away
• Do not drive across a slope or side tipping may occur
• Do not turn sharply at speed. Forklifts overturn very easily. They are narrow
wheelbase trucks with a high centre of gravity
• If your forklift is overturning. Grab the steering wheel, brace your feet, lean in the
opposite direction of the fall and do not attempt to jump clear.
• Watch out for rear end swing. Forklifts steer from the rear and the rear end will
swing out very wide. When travelling and turning the rear end, swing will be
three times that of the forward speed of the forklift. Stay as close as possible to
the inside of narrow corners when turning and watch out for pedestrians or
objects
• Revving the engine when lowering a load makes no difference; lowering is
gravitational.
• Do not drive reach trucks with the reach out as this alters the vehicle’s C.O.G.
• Give way to police, fire, ambulance or other emergency vehicles at all times.
Other workers and pedestrians should be aware of the need to keep clear of a
forklift while loading and travelling. In particular, no one should walk behind a forklift
while it is loading or stacking or walk under an elevated load.
Precautions must be taken when operating over roadways, footpaths and other
public areas.
The rear end swing of a forklift can be particularly dangerous as the rear end can
swing out in a very wide arc and can travel extremely fast when turning.
45
TLILIC0003 Licence to operate a forklift truck Version 3
13.3 Placement of Loads
• When putting the load down, always bring the load over the stack before
tilting forwards
• Deposit the load with the mast vertical
• If placing loads into stacks or racks make sure the heaviest item is at the base
of the stack
• Make sure loose items are not stacked high, (wrap or strap loose items)
• Ensure shelves or racks are weight rated and know the weight of your loads
• Never stack too high as this will create an unstable stack
• Make sure ground is firm, dry and level
• Always try to stack neatly, neat stacks are safe stacks
13.4 Loading trucks
• Always load pallets alternately on both sides of a truck. A truck can overturn if
one side is empty and the other side has a full load
• Make room by shifting the truck if there is no room to load both sides.
13.5 Loading Pantech’s (large enclosed vans)
Make sure:
• That the mast is not too high to enter the van
• That there is sufficient ventilation
• That the truck will support the combined weight of the forklift and the load
• That the bridge plate is in place and secure
• That the van is chocked
• That the driver of the van has removed the keys from the ignition and has left
the cabin during loading
• The load is kept low during loading
13.6 Loading loads with two forklifts
Lifting a load with two forklifts is very hazardous. The precautions listed below must be
taken when lifting with two forklifts:
• Dual lifts should only be carried out by experienced operators
• The operation must be controlled by an experienced third person who has
responsibility
• Each forklift must not lift more than 75% of its rated capacity given stability,
position of load centre and other factors affecting the safe working load (SWL)
• The load must be only carried the distance necessary to clear the load carrier
• Loads must be raised and lowered simultaneously
• Order pickers must not be used for dual lifts
46
TLILIC0003 Licence to operate a forklift truck Version 3
If one forklift lowers more quickly than the other, the load becomes uneven. The
diagram on the previous page shows forklift B lowering more quickly than forklift A
causing:
• The weight to move immediately to the tip of the fork arms on A
• Pressure put on the mast of forklift B which could cause it to bend or break
The load slips along the fork arms changing the position of the load centre.
13.7 Parking
1. Always find a level, out of the way, place to park. If you must park on an incline,
you must also chock the wheels before leaving the forklift.
2. Park clear of fire and emergency exits, power switches, firefighting appliances,
first aid facilities, gas refuelling stations and fuel pumps.
3. Engage handbrake and select neutral gear
4. If the tips of the forks cannot be lowered to the ground, park so that the forks
do not create a tripping hazard
5. Turn the ignition off and remove the key to prevent unauthorised use
6. Isolate the power source if at the end of a shift i.e. LP gas should be turned off
to prevent leakage
7. Make sure you always park clear of:
• Doorways
• Emergency exits
• 3m from train lines
• Flammables/hazardous materials
• First aid stations
• Blind corners
• Pedestrian walkways
47
TLILIC0003 Licence to operate a forklift truck Version 3
Learning Check 4
1. Circle true or false for each of the following statements.
You must never:
Load with one fork tyne True or False
Use order pickers for dual lifts True or False
Use two forklifts to carry a load True or False
Park hard up against another forklift True or False
Jump out if your forklift is overturning True or False
2. When raising the load, you should rest the load against the ……………………
of the fork.
3. What should you do when driving towards a blind corner?
……………………………………………………………………………………………………………
……………………………………………………………………………………………………………
48
TLILIC0003 Licence to operate a forklift truck Version 3
14. FORKLIFTS AND ELECTRICITY
Keep a safe distance from electric power lines. Find out where all power lines are
located in your workplace. Do not unload a truck under power lines (to avoid the
mast making contact with the lines when the forks are raised).
You MUST know and remember the safe distances when working near power lines.
To determine voltage of the lines, you must consult with the relevant authorities.
Prescribed distances are dependent on the voltage of the powerline. In addition,
Australian Standard AS2550 (Cranes, hoists and winches – Safe use), describes the
operation of cranes and other elevating working platforms in proximity to powerlines.
This standard provides general guidance regarding safe working practices for
machinery near powerlines, with clearances depending on whether the work is
conducted with or without a spotter.
With Spotter:
3m away for low
voltage
Without Spotter:
at least 6.4m
With Spotter:
8m away for low
voltage
Without Spotter:
at least 10m
49
TLILIC0003 Licence to operate a forklift truck Version 3
Stay at least 6.4m away from distribution lines on poles (low voltage) and at least 10m
away from transmission lines on towers (high voltage).
If a spotter is used:
• 3m away for low voltage
• 8m away for high voltage
If required to work closer than these distances you must first contact the supply
company for permission. The supply company can either de-energise the lines,
insulate them or provide an approved spotter when working nearby.
Procedure if accidental contact is made with power lines:
1. Stay on the machine and warn others to stay clear
2. Try to break contact if the engine is still running
3. Do not leave the forklift until the electricity has been turned off
4. If safe, jump well clear of the forklift
5. Do not make contact with the ground and the forklift at the same time.
6. Warn all others to remain no less than 8m away from the forklift
7. Forklift must be fully inspected before it can resume working
Tiger Tails (as shown below) are a simple black and yellow plastic sleeve that can be
attached to power lines. They are a visual aid used to highlight the location of live
wires in relation to where the work will be carried out.
Remember, if there is a requirement to get closer than the recommended minimum
safe distances, regulatory authorities must be notified prior to the work commencing.
DO NOT GUESS
ELECTRICITY IS DANGEROUS, INVISIBLE AND IT WILL KILL
50
TLILIC0003 Licence to operate a forklift truck Version 3
15. FIRST AID
Forklift operators work in a high risk industry. Not only are there many minor injuries,
but there are also serious injuries where the injured person will need first aid to restore
breathing, heartbeat or to stem blood flow.
According to WorkCover statistics, between 1985 and 2003, 49 people have been
killed in forklift incidents.
Know the location of the first aid room and the nearest first aid kit. There must be a
first aid kit on every floor of a multi-story building site or within 100m of any part of the
workplace.
The standard first aid symbol in Australia is a white cross on a green background.
It is recommended that forklift operators take the time to obtain an approved first aid
certificate.
In the case of an emergency it is of critical importance to remain calm and
communicate accurate descriptive information to the necessary people.
This process can vary from site to site however in most cases you will be required to
inform supervisors, other workers and emergency services;
• The nature of the emergency (WHAT)
• The exact location of the emergency (WHERE)
• How the incident occurred (HOW)
51
TLILIC0003 Licence to operate a forklift truck Version 3
16. COMMUNICATIONS
Understanding how to use communication devices correctly is an important part of
work place procedures and safety. Many companies will adopt varying methods of
communication such as:
• Two-way radios
• Verbal questioning and listening to confirm understanding
• written instruction
• Hand signals
• Audible and visual warning devices
It is of vital importance that communication techniques and devices are checked
for suitability and functionality prior to the work commencing.
17. TRAFFIC WARNING SYSTEMS
A person conducting a business or undertaking with management or control
of powered mobile plant at a workplace must ensure it does not collide with
pedestrians or other powered mobile plant. If there is a possibility of collision, I.E the
brakes and steering fail on the forklift the plant must have a warning device alerting
person who may be at risk from its movement.
workplaces can be designed with vehicle and pedestrian routes that are separated.
Mobile plant can be designed so the operator can see easily and the plant can
be fitted with speed limiters and traffic warning devices. Common warning devices
fitted include:
• Audible – horn
• Visual warning devices – flashing beacon/strobe light
• Alert systems –
o Collision Awareness Forklift Look Out Sensor
o Overhead Forklift Door Monitor with Sensor
o Worker Alert System Vibration Unit
52
TLILIC0003 Licence to operate a forklift truck Version 3
18. TRAFFIC MANAGEMENT PLANS If you have a large workplace with a high volume of traffic a traffic management
plan can help you communicate how you are managing traffic risks in your
workplace.
A traffic management plan may include details of:
• the desired flow of pedestrian and vehicle movements
• the expected frequency of interaction of vehicles and pedestrians
• illustrations of the layout of barriers, walkways, signs and general arrangements to
warn and guide traffic around, past, or through a work site or temporary hazard,
and how short term, mobile work and complex traffic situations will be managed.
A traffic management plan could also set out:
• responsibilities of people managing traffic in the workplace
• responsibilities of people expected to interact with traffic in the workplace, and
• instructions or procedures for controlling traffic including in an emergency.
Example of traffic control measures for truck loading and unloading
Clearly designated pedestrian
walkway protected by physical barriers with
staggered barriers to control approaching
pedestrians.
Pedestrian exclusion zone has been
established for a distance equal to the height
of the load from the ground plus an additional
allowance for the type of load.
Beam from pedestrian-sensing
device.
Barriers, bollards, witches hats or
paint marking the pedestrian exclusion zone.
Warning light activated by
pedestrian sensors.
Establish a safety zone for the driver and
other pedestrians. The driver should be in full
view of the forklift operator. Stop the loading
and unloading activities if the driver cannot be
seen or needs to enter the exclusion zone.
Alternatively, if it is safe to do so the system of
work can provide for the driver to stay in the
cabin during loading and unloading. Effective
communication systems between the plant
operator and the driver should be used such as
a system of hand signals or two-way radios.
53
TLILIC0003 Licence to operate a forklift truck Version 3
19. GENERAL SAFETY RULES
• When a work platform is elevated, the driver of the forklift must remain at the
controls at all times. Park brake applied, gear selection in neutral with engine
running.
• In the event of any fault being revealed at any time or if the forklift becomes
unsafe in any way:
▪ Remove the ignition keys to stop unauthorised use
▪ Turn off the gas to prevent leaks
▪ Tag the forklift as defective
▪ Report the matter immediately to your supervisor to be fixed
• Do not make repairs, alterations or adjustments to any forklift unless authorised
and qualified.
• Do not allow anyone to stand or pass under elevated fork or attachments,
whether loaded or empty.
• Do not use additional counterweight to increase the load capacity of any
forklift unless approved by the manufacturer.
• Always approach rail lines and speed humps at a 45º angle and slow down.
• Do not operate a forklift unless a compliance plate (data plate) is fitted.
• Do not operate a forklift on a public road unless the forklift is registered, has
lights, turning indicators and warning devices fitted. Have appropriate class of
driver’s licence covering the gross vehicle mass of the forklift.
• Never lift unstable loads (restack pallet if required).
• Check load weights and operate only within the rated capacity of your forklift
truck.
• When operating a forklift on wet or slippery surface you should take the
following evasive actions to minimise the risk of losing control.
• Reduce speed
• Avoid using ramps or steep inclined pathways
• Take wide turns (slowly)
• Proceed with care - (after there’s been an
interruption keep going, safely avoiding harm or
danger)
54
TLILIC0003 Licence to operate a forklift truck Version 3
20. LOAD CENTRE DISTANCE
Load centre distance is defined as:
‘The distance from the heel (or vertical face) of the forks to the centre of gravity of the
load’
Most palletised loads are square and evenly stacked in which case the load centre
will be in the centre of the load. Lifting loads that are not against the heel means the
Load Centre Distance will be increased which in turn will lower the forklifts height and
weight capacity.
By increasing the load centre, you decrease the capacity of the forklift.
Load centre distance (L.C.D) increase = height & weight decrease.
600mm is the Australian standard load centre distance although it is illegal in
Australia to use a forklift with an LCD rated below 500mm. Always check the data
plate for the rated capacity before use.
55
TLILIC0003 Licence to operate a forklift truck Version 3
21. CALCULATIONS
As part of this course you will need to demonstrate that you can:
• Calculate the weight of the load you will be carrying
• Read and understand load charts to calculate which loads are within the
capacity of the forklift
• Read and understand load charts to calculate maximum working loads with the
mast in different positions
Example:
The load to be moved is bags of sand stacked on a pallet.
• 60 bags on the pallet
• Each bag is 20kg
• The pallet weighs 30kg
What is the combined weight of the bags and the pallet?
(50 x 20) + 30 = 1230kg
Learning Check 5 1. Using the calculated load (above) and the data plate (below) answer the
following questions – (circle answer)
Can your forklift truck lift the load? YES NO
Can you lift the load with your mast tilted forward? YES NO
Can you lift 1820kg with a load centre of 800mm? YES NO
56
TLILIC0003 Licence to operate a forklift truck Version 3
2. Your forklift requires some minor repairs; under what circumstances can the
operator make the repairs?
A. All HRW licence operators can.
B. If the supervisor says it’s ok.
C. Only if they are authorised and competent to do repairs.
3. You have just picked up a load, why should you centre the side shift before
travelling with the load?
A. A. So the load looks tidy.
B. B. To maintain the stability of the load and forklift.
C. C. So the operator can see properly.
4. What does the term, “load centre distance” mean?
A. The distance to the middle or the forklift blades.
B. From the mast to the middle of the forklift blades.
C. From the vertical face and the horizontal face of the fork tynes to the load
centre of gravity.
5. If your fork lift truck has a 600mm LCD and a SWL of 3000kg which load is within
tolerance? (circle your answer)
57
TLILIC0003 Licence to operate a forklift truck Version 3
6. The load to be moved is a precast block secured on a
pallet.
• Precast block 730kg
• The pallet weighs 43kg
What is the combined weight of the precast block and the pallet?
Show all calculations.
……………………………………………………………………………………………………………
……………………………………………………………………………………………………………
…………………………………………………………………………………………………………
7. The load to be moved is four drums stacked on a pallet.
• Four drums on the pallet
• Each drum’s tare weight is 9.8kg
• Each drum’s capacity is 208L (filled with water)
• The pallet weighs 34kg
What is the combined weight of the drums, contents of the drums and the pallet?
Show all calculations.
……………………………………………………………………………………………………………
……………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
…………………………………………………………………………………………………………
8. The load to be moved is an IBC filled with water.
• Tare weight of IBC is 56kg
• The amount of water is 1000L (1000kg)
What is the combined weight of the IBC and the water?
Show all calculations.
……………………………………………………………………………………………………………
……………………………………………………………………………………………………………
58
TLILIC0003 Licence to operate a forklift truck Version 3
22. PRE-ASSESSMENT CHECK
(This must be complete before the Final Assessment)
1. Before you start work who should you communicate with about site hazards?
2. List 10 common hazards you should be aware of before operating a forklift
truck
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
3. It is important to confirm your work conditions and responsibilities before
commencing work, other than site hazards what other conditions and
responsibilities should you be aware of before you start work. List 6 examples.
1.
2.
3.
4.
5.
6.
59
TLILIC0003 Licence to operate a forklift truck Version 3
4. The Hierarchy of control is a six step approach to controlling hazards in the
workplace. What are the six steps, starting with first consideration and working
to the last step/level of control?
1. ____________________
2. ____________________
3. ____________________
4. ____________________
5. ____________________
6. ____________________
5. Demonstrate knowledge of power line safety distances for South Australia,
Low voltage with a spotter m
Low voltage without a spotter m
High Voltage with a spotter m
High Voltage without a spotter m
6. Do Tiger Tails allow you to work closer than the distances given because they
provide isolation and protection when working near powerlines?
Explain your answer.
7. When you have to move a load with your forklift from one location to
another, what would you consider in determining the travel route before you
carry out your task?
60
TLILIC0003 Licence to operate a forklift truck Version 3
8. If you are going to operate a forklift in an area that allows pedestrians to
enter your work area, what control measures could be used to control their
movements?
9. If you had to operate a forklift in a warehouse that had very poor lighting and
blackened areas, what would you require to be able to work safely?
10. What is produced when charging batteries for an electric forklift?
11. Why is the rear end of a forklift dangerous when travelling and turning? (a)
Who is at most at risk? (b)
a)
b)
12. Why must the operator ensure the forklift truck is turned off when refuelling?
13. Name 3 communication styles you could use whilst operating a forklift truck?
1.
2.
3.
14. In an emergency list 3 people you would contact and what would you
communicate to them?
1.
2.
3.
61
TLILIC0003 Licence to operate a forklift truck Version 3
15. When assessing a load how would you determine the weight of a load?
List 3 examples
1.
2.
3.
16. Name 8 pre-start checks that you would make before starting your forklift?
1.
2.
3.
4.
5.
6.
7.
8.
17. If during your prestart checks you found that the Data Plate was missing or
unreadable or the machine is not in acceptable working order, what would
be your responsibility?
18. Where can you find a forklifts Rated Capacity and what are the three
elements that form it?
Can be found:
Element 1:
Element 2: _____________
Element 3:
62
TLILIC0003 Licence to operate a forklift truck Version 3
19. Whilst travelling up or down a ramp without a load in which direction must the
forklift face? (a)
Is this method different when travelling up or down a ramp with a load? (b)
a)
b)
20. What are the risks if a person is under a raised load whilst you are operating
the forklift?
21. What is the optimum load travel height?
22. What is the likely outcome of travelling with a load raised?
23. List 7 things that could change your forklifts centre of gravity and result in the
forklift tipping sideways?
1.
2.
3.
4.
5.
6.
7.
63
TLILIC0003 Licence to operate a forklift truck Version 3
24. Give 4 examples of areas considered unacceptable as a parking place for
forklift trucks?
1.
2.
3.
4.
25. Calculate the following:
The load to be moved is paving stones stacked on a pallet.
• 144 paving stones on the pallet
• Each paving stone weighs 2kg
• The pallet weighs 40kg
What is the combined weight of the paving stones and the pallet?
Show all calculations.
64
TLILIC0003 Licence to operate a forklift truck Version 3
23. ASSESSMENT
Your trainer will explain the methods of assessment to you to demonstrate
competency of TLILIC003 Licence to operate a forklift truck.
Theory Assessment
You will need to undertake:
• Two (2) knowledge assessments
• One (1) calculations assessment
Practical Assessment
You will need to undertake:
• a performance assessment on the forklift
Ask your trainer if you have any questions about the assessment process for this unit.
GOOD LUCK WITH YOUR ASSESSMENTS