This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
For Temperature Programmed Desorption,Reduction, Oxidation and Chemisorption
Thermo Scientific TPDRO 1100Advanced Catalyst
Characterization
Metal supported catalysts
Oil industry catalytic processes
Catalytic converters
Materials surface acidity
Catalytic combustion
Environmental catalysis
Part of Thermo Fisher Scientific
s u r f a c e a n a l y s i s
Catalysts improve our everydaylife and help to preserve theenvironment Catalysts are ubiquitously used in modernindustrial processes such as in petrochemicalplants, pharmaceutical,fine chemistry andfood industry. Catalysts are typicallycomposed of an active phase (usually anoble metal or an acid/base site) that isdeposited and dispersed on a poroussupport (i.e. alumina, silica, etc.). The activephase in a solid catalyst has high affinity for the molecules of given reactants. The molecules are first chemisorbed ontothe active surface before reacting betweenthemselves. The catalysts activity, for agiven reaction, is usually proportional to thenumber of surface active sites. As for metalsupported catalysts, the active sites areconstituted by the exposed metallic surface.There are several well known analyticaltechniques permitting an evaluation ofparameters such as metal specific surfacearea, the metal dispersion and the averagemetal aggregate size. One of the fastestand reliable technique is the pulsechemisorption in flow. Additional studiesrelated to catalysts, provide the determinationof the energies involved in the chemisorptionand desorption processes of the reactantsand products. The above parameters can beobtained in an automated way by means ofthe Thermo Scientific TPDRO 1100 usingthe available techniques of thermalprogrammed desorption (TPD), reduction(TPR), oxidation (TPO) and pulse chemisorption.
The complete characterization sequence ofan active solid generally consists of twoseparate phases: the pre-treatment and theanalysis. Depending on the type of analysisrequired, the sample needs to be activatedbefore the test. For instance, when performingtemperature programmed desorption, thesurface of the catalyst must first be rid ofpre-adsorbed gas species on its surface andthen saturated with a suitable reactive gas.The pre-treatment procedure is usually avery time consuming and a delicate processas all the analytical.
results are pre-treatment sensitive. A sequence of different gases flows throughthe catalyst bed at different temperatures.Heating rates must be performed with highprecision to ensure reliable results. The Thermo Scientific TPDRO 1100 featuresa fully automatic pre-treatment sequencewith an unlimited selection of procedures.The settings of the activation proceduresare memorized in the dedicated softwaredatabase, which can be readily recalled andapplied on similar samples thereforesimplifying the setup process.
Thermo Scientific TPDRO 1100: A technological breakthrough for advanced
Metal Supported Catalysts • Oil Industry Catalytic Processes • Catalytic Converters
Catalysts characterization now made easier and faster with theinnovative Thermo Scientific TPDRO 1100
The development of catalystshas contributed enormously to
change our everyday life.
Thermo Scientific TPD
RO 1100
Advanced Catalyst Characterization
For Temperature Program
med D
esorption, Reduction, Oxidation and Chem
isorption
Catalyst activation and analysis: "parallel" is faster than "serial" !Sometimes the pre-treatment procedure might lasts for hours, whereas the analyses arerelatively short. Once the catalyst is activated for the analysis, it must not be exposed toany other reactive gases such as oxygen in the air, but should be kept under an inert gas. An innovative and proprietary reactor designed by Thermo Fisher Scientific, circumvents thisproblem of sample exposure to atmospheric gases after the sample pretreatment step. Thereactor can be closed and isolated from the environment after catalyst activation and thecatalyst can be kept under an inert gas for subsequent operations. The user is able totransport the complete reactor along with the isolated and pretreated catalyst avoiding anyrisk of sample contamination prior to the analysis.
804863
750443
200Time ( min )
0 50 100 150 200
1200
Sig
na
l (m
V)
0
200
400
600
800
1000
1200
600
Te
mp
era
ture
( °
C )
0
100
200
300
400
500
600
Simultaneous pre-treatment and analysis on two different catalysts
Unlimited automatic sequence of multiple preparation /analysis
parallel is faster than serial !
This important feature generates a number of additional possibilities:
• The catalyst activation can be performed in the Thermo Scientific TPDRO 1100 pre-treatmentport or in another system (i.e. in a fume hood, inside a controlled environment, etc.)
• The Thermo Scientific TPDRO 1100 can simultaneously and independently perform theactivation on a sample in the pre-treatment port and the analysis on another sample inthe analysis port, saving valuable lab time and practically doubling the productivity
In addition to the above operations, the Thermo Scientific TDPRO 1100 works sequentially,with no need to touch the reactor when moving from the pre-treatment to the analyticalstage. The instrument will automatically perform the pre-treatment sequence of catalystactivation followed by the experiment, without any operator’s intervention.
Precise gas control for high sensitivity In the Thermo Scientific TPDRO the flow is regulated by a mass flow controller in a single gas line detection passing first to the TCD reference channel and then to the reactor and finally again to the TCD
analytical channel. This configuration ensures that the flow is identical in both the TCD filaments, thus giving the ultimate in baseline stability and high sensitivity detection therefore more reliable results. Very low metal percentage catalysts can be tested easily, minimizing the sample load in the reactor andthus avoiding problems like re-adsorption and channelling effects.
Precise gas injection systems for For calibration and pulse chemisorption, the probe gas can be injected into the reactor manually using apulse chemisorption gas tight syringe or automatically through a high precision loop valve system. The loop selection can be
as small as 0.15 cc and without "shutter" dead volume which is generating noise peaks in the baseline.Pulse gas can also be made of a low percentage mixture of a reactive gas in a suitable inert gas, thus permitting extremely small gas injections to test very low metal percentage catalysts.
Two independent ovens The Thermo Scientific TPDRO features two separate and independent ovens. Both can be used improve productivity independently for the sample activation (pre-treatment port) or the experiment (analysis port) up to
1100 °C. The ovens are anti-magnetic to avoid additional baseline noise when the carrier is polar. Thereis also a special fast cooling connection to compressed air to facilitate the cooling of the oven.
Temperature control both during the Oven temperature is raised linearly in a wide range of values. Rates of up to 40 °C/min is possible up toincrease and decrease phases of the 750 °C or 20 °C/min up to 1100 °C extending the analytical performance especially in TPD experiments.catalyst investigation In addition, a specially designed system permits to control the temperature rate also when decreasing
the temperature. This allows detecting possible chemical reactions even during the sample cooling process.
Real sample temperature A thermocouple is inserted into the special reactor directly over the sample or inside the catalyst bed. monitored continuously The probe is very thin, thus featuring a very fast response time to temperature variations. In addition,
the sensor itself is protected by a quartz shield that avoids contact between the thermocouple and the reactive gases.
Additional analytical possibilities Single point BET in flow analysis permits the "in-situ" evaluation of the total surface of the catalyst before and after the experiment, thus revealing immediately if morphological changes occurred to the sample during the course of the analysis.
External thermoregulation bath The reactor can be fitted to a special recirculation bath for temperature control in the range of room temperature or even below zero degrees Celsius. The temperature can be precisely regulated by means of an external liquid circulation system during pulse chemisorption experiments.
Vapour generator optional kit A number of organic vapours can be generated at constant temperature and injected quantitatively into the reactor, thus saturating the catalyst. The vapour can then be desorbed by TPD experiment.
Additional detectors for more In sequence to the TCD detector, a suitable mass spectrometer can be connected to the Thermo comprehensive investigation of Scientific TPDRO. The advantage is that the MS provides information of the gaseous species evolvingsurface reactions from the catalyst, permitting, both a qualitative and quantitative determination
Special design reactor with built-in by-pass valveA special reactor has been designed toinsulate the catalyst from the enviromentafter the activation. The unique reactorpermits to prepare and measuresimultaneously two catalysts, saving
valuable lab time. In addition it is possibleto prepare the catalyst in externalpreparation devices, especially when usingdangerous or very corrosive gases forutmost safety of the operator. When thesample is ready, the sealed reactor can betransferred safely to the Thermo ScientificTPDRO for testing.
Temperature programmed reductionand oxidationThe objectives of this technique areessentially the following:• To find the most efficient reduction/
oxidation conditions• To identify the supported precursor phases
and their interactions with the support• To characterize complex systems, as
bimetallic or doped catalyst, to determinethe role of the second component and toestablish alloy formation or promotioneffects
TPR example on Co catalyst
In the TPR technique an oxidized catalyst issubmitted to a programmed temperatureincrease, while a reducing gas mixture ispassed over it (usually, hydrogen diluted insome inert gas as nitrogen or argon). In theTPO technique, the catalyst is in the reducedform and it is submitted to a programmedtemperature increase, but in this case, anoxidizing mixture of gas (typically oxygen inhelium) is passed over the sample.
TPO example with temperature decreasecontrol
Temperature programmed desorptionIn the TPD studies the solid system ispreviously activated and then saturatedwith a probe reactive gas in isothermalconditions. During the temperatureprogrammed desorption analysis, thesample is submitted to an increasingtemperature at constant rate and it is sweptby an inert gas such as helium, argon ornitrogen. The sample surface desorbs thegas that has been previously chemisorbedand the thermal conductivity detectormonitors the process. The informationproduced by TPD experiments are related to:• Energetic abundance of active sites• Adsorption/desorption energy• Free metal surface area
Ammonia TPD spectra at differenttemperature rates
Example of hydrogen TPD
Pulse chemisorption in flowThe chemisorption analysis in a flow systemis denoted Pulse Chemisorption. The gas tobe chemisorbed is introduced as a pulse, viaa calibrated loop valve, into the stream ofthe inert carrier gas flowing through thereactor and the sample. The catalyst ispreviously activated by an appropriate pre-treatment procedure and then submitted tochemisorption. The result is demonstratedlike a series of peaks with increasing peakheight. The software then automaticallycalculates the exposed metal area andmetal dispersion.
Hydrogen 5% pulses on Pt catalyst
1539
356
1627
429
1494
327
1680
805
30Time ( min )
0 10 20 30
5000
Sig
nal
(mV
/g)
0
1000
2000
3000
4000
5000
800
Tem
per
atu
re (
° C )
0
200
400
600
800
BR11002_E 09/09C
Thermo Fisher Scientific S.p.A, Milan, Italy is ISO Certified.
Specifications, terms and pricing are subject to change.Not all products are available in all countries. Pleaseconsult your local sales representative for details.
In addition to these offices, ThermoFisher Scientific maintains a network of representative organizationsthroughout the world.
• Metal specific surface area• Metal dispersion percentage• Peaks automatic or manual integration,
integration limits, maximum peaktemperature, etc.
• Calculation of metal percentage from TPRexperiments
• Calculation of adsorption/desorptionenergy from TPD
• Calculation of mass / metal percentagecorrection in multiple experiments
• TPR/TPO temperature/time profiles
GraphsTCD signal (mV or mV/g), oven and sampletemperatures versus timeTCD signal (mV or mV/g ) versus oven orsample temperaturePlot of activation energy for desorptionOverlay of multiple experiments on a singlegraph with multiple calculations
Special design softwareThe software of Thermo Scientific TPDRO hasbeen specifically designed to run the samplepreparation and analyses automaticallystore data in real time, generate graphs,reports and calculations. All the operationsrequired for processing the data arecontained in the Thermo Scientific TPDROsoftware suite, like baseline subtraction,automatic peaks integration routine, tabularresults, overlay of different experiments aswell as printout of results. Reports can alsobe generated directly in the rtf format. Thesoftware is integrated with a number ofdatabases containing all the essentialinformation related to gases and gas-vapourmixtures, reactions, samples, metals,reaction stoichiometry, preparation andanalytical methods.