Top Banner
- 1 - The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on to a section of tube liner
14

The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

Jul 19, 2018

Download

Documents

phungquynh
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 1 -

The Flamethrower by Stuart Anderson

Materials needed.

Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on to a section of

tube liner

Page 2: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 2 -

Pinch the tube and tube liner between your thumb and index finger and slowly twist it

next to (not directly in) an open flame.

A nice lip will be the result on the back end. Be sure not to melt too much or the tube will

close over.

Page 3: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 3 -

Paint the slots with any orange enamel paint. Be liberal with the application and make

sure it gets well into all four slots.

Wipe off the excess paint with a paper towel.

Page 4: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 4 -

Cut the other end of the liner tube. You need about I inch of liner extending past the front

of the Shumakov tube. Insert the tube onto your mandrel.

Page 5: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 5 -

Put the mandrel into your vise adapter and tighten.

Tie on your 6/0 orange thread. Make a nice “hump” of thread in front of the Shumakov

tube. Be sure to use many wraps to wedge the Shumakov tube into the back lip of the

liner tube.

Page 6: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 6 -

Tie in an orange schlappen feather.

Spin around the tube and tie back the schlappen fibers.

Page 7: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 7 -

Tie in a yellow schlappen feather.

Spin around tube and tie back the yellow schlappen fibers.

Page 8: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 8 -

Tie in a red schlappen feather.

Spin around tube and tie back the red schlappen fibers.

Page 9: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 9 -

Pull back the fibers of a claret ringneck pheasant feather.

Tie in the ringneck pheasant father by the top of the feather.

Page 10: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 10 -

Spin the pheasant around the tube and tie back the fibers.

Add a small bunch of orange bucktail, calftail, or polar bear fibers.

Page 11: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 11 -

Add a small bunch of pearlescent crystal flash.

Page 12: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 12 -

Add four red hackle tips. Tie them in flat over the hair and crystal flash.

Page 13: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 13 -

Take the tube off of the mandrel and trim the liner tube within 1/16” from the head.

Using the same technique as at the back of the tube, burn a “lip” at the head.

Page 14: The Flamethrower - Tube Flies for Salmon and Steelhead · The Flamethrower by Stuart Anderson Materials needed. Insert a Juri Shumakov Long Range Tube (either brass or aluminum) on

- 14 -

Tie up a few more and you are ready to go!