-
th
Grand Hall BITEC, Bangkok, Thailand6-7
SEPTEMBER2018
The Annual Meeting 2018 of MRS-ThailandInnovative Textiles for
Future Healthcare Application
CONFERENCE & EXHIBITION
Abstract Book
The 10th International Conference onMaterials Science and
Technology In conjunction with
Organizers Co-organizers
Platinum Sponsors Gold Sponsors
ExhibitorsMSAT-10 App
www.mtec.or.th/msat-10
-
th
The 10th International Conference on Materials Science and
Technology
Disclaimer
�is book contains the abstracts of the papers presented at �e
10th International Conference on Materials Science and Technology
(MSAT-10). �ey re�ect the authors opinionsand are published as
received a�er revision by the authors.
�e committee assumes no responsibility for the accuracy,
completeness or usefulness of thedisclosed information.
Unauthorized use might infringe on privately owned patents or
publication rights. Please contact the individual author(s) for
permission to reprint or make use of information from their
papers.
2
-
th
The 10th International Conference on Materials Science and
Technology
OrganizersNational Metal and Materials Technology CenterNational
Science and Technology Development AgencyMinistry of Science and
Technology
Co-organizersChulalongkorn UniversityMetallurgy and Materials
Science Research InstituteMaterials Research Society of �ailand
Platinum SponsorsPhotonics Science Co., Ltd.IRPC Public Company
Limited
Gold SponsorsRI Technologies Ltd.�ai Parkerizing Co., Ltd.Bara
Scienti�c Co., Ltd.Adtech Service Automation Co., Ltd.Kinetics
Corporation Ltd.
ExhibitorsSilpakorn UniversityPlastics Institute of
�ailandPuditec Co., Ltd.
3
-
th
The 10th International Conference on Materials Science and
Technology
CONTENTS
Preface 5Committees 6Technical Program 9MSAT-10 Venue and
Exhibitor list 15List of Oral & Poster Presentations 16
Abstract of MSAT-10PL: Plenary Lectures 33BIO: Biomedical
Materials and Devices 38CER: Ceramics 64DMC: Design and
Manufacturing + 117
Computational Science and EngineeringENR: Materials for Energy
131ENV: Materials Technology for Environment 151MET: Metals, Alloys
and Intermetallic Compounds 182POL: Polymers 218TES: Testing and
Reliability 256
Special Session:TEX: Innovative Textiles for Future Healthcare
Application 268
4
-
th
The 10th International Conference on Materials Science and
Technology
Preface
Dear Colleagues,
On behalf of the Organizing Committee, I would like to welcome
you all to the 10th International Conference on Materials Science
and Technology (MSAT-10) held from September 6 to 7, 2018 in
Bangkok, �ailand.
MSAT is recognized as one of the major series of conference in
materials science and technology. �e bi-annual conference strives
to be a premier international multidisci-plinary conference. �e
event provides anarena for all stakeholders from academics,
researchers and industrial leaders to share their latest research
�ndings, to discuss novel applications and to identify the
challenges that lie at the frontier of materials science.
In conjunction with MSAT-10, two special events to be run along
are Innovative Textiles for Future Healthcare Application and the
MRS-�ailand Annual Meeting.
To support of sustainable and green environment in �ailand, we
are going to transform the MSAT towards paperless conference. All
information needed for the MSAT-10 will be available for
participants via the MSAT-10 mobile application and the conference
website.
Regarding the conference activities, we are proud to have 4
plenary and 21 invited lectures given by distinguished researchers
in the �eld of materials technology around the world. �ey include
94 oral research presentations and 109 poster presentations
covering recent progress and R&D activities ranging from
fundamental research to applied research in the �elds of materials
science and technology.
We are also delighted to announce the number of participants to
MSAT-10 to be over 500 persons from Germany, India, Japan,
Malaysia, United Kingdom, United State of America, Singapore,
China, South Korea and �ailand.
Lastly, I would like to thank all of the sponsors who have
contributed to the MSAT-10, without whom it would be di�cult to
organize a successful international conference. �eir contributions
are greatly appreciated.
Yours sincerely,
Dr. Julathep KajornchaiyakulChair of MSAT-10
5
-
th
The 10th International Conference on Materials Science and
Technology
COMMITTEESChair Dr. Julathep Kajornchaiyakul National Metal and
Materials Technology Center
Vice Chairs Dr. Aree �anaboonsombut National Metal and Materials
Technology Center Dr. Kritsada Prapakorn National Metal and
Materials Technology Center Ms. Siriwan Tantawechkit National Metal
and Materials Technology Center
Scienti�c Committee Dr. Worasit Kanjanakijkasem Burapha
UniversityDr. Dumnoensun Pruksakorn, M.D. Chiang Mai
UniversityAsst. Prof. Dr. Kedsarin Pimraksa Chiang Mai
UniversityDr. Robert Molloy Chiang Mai UniversityAssoc. Prof. Dr.
�apanee Sarakonsri Chiang Mai UniversityAsst. Prof. Dr. Boonrat
Lohwongwatana Chulalongkorn UniversityAsst. Prof. Dr. Sorada
Kanokpanont Chulalongkorn UniversityAssoc. Prof. Dr. Duangdao
Aht-Ong Chulalongkorn UniversityAsst. Prof. Dr. Dujreutai Pongkao
Kashima Chulalongkorn UniversityAssoc. Prof. Dr. Gobboon Lothongkum
Chulalongkorn UniversityAsst. Prof. Dr. Mantana Opaprakasit
Chulalongkorn UniversityDr. Natthaphon Raengthon Chulalongkorn
UniversityAssoc. Prof. Dr. Nisanart Triphol Chulalongkorn
UniversityDr. Numpon Insin Chulalongkorn UniversityAsst. Prof. Dr.
Panyawat Wangyao Chulalongkorn UniversityAsst. Prof. Dr. Pornapa
Sujaridworakun Chulalongkorn UniversityAssoc. Prof. Dr. Rojana
Pornprasertsuk Chulalongkorn UniversityAsst. Prof. Dr. Sirithan
Jiemsirilers Chulalongkorn UniversityAssoc. Prof. Dr. Songphol
Kanjanachuchai Chulalongkorn UniversityAssoc. Prof. Dr. Supatra
Jinawath Chulalongkorn UniversityAsst. Prof. Dr. �anakorn
Wasanapiarnpong Chulalongkorn UniversityAsst. Prof. Dr. Jeremy John
Mercuri Clemson UniversityDr. Lada Punsukumtana Department of
Science ServiceDr. Parinya Boonmalert Kasem Bundit UniversityDr.
Rungsima Chollakup Kasetsart Agricultural and Agro-Industrial
Product Improvement InstituteAsst. Prof. Dr. Duangrudee
Chaysuwan Kasetsart UniversityAsst. Prof. Dr. Ratchatee
Techapiesancharoenkij Kasetsart UniversityAsst. Prof. Dr. Nonglak
Meethong Khon Kaen UniversityAsst. Prof. Dr. Suparat Rukchonlatee
King Mongkut’s Institute of Technology
LadkrabangAsst. Prof. Dr. Surat Areerat King Mongkut’s Institute
of Technology
LadkrabangDr. Kittichai Fakpan King Mongkut’s University of
Technology
North Bangkok
6
-
th
The 10th International Conference on Materials Science and
Technology
Asst. Prof. Dr.-Ing. Pruet Kowitwarangkul King Mongkut’s
University of Technology North Bangkok
Assoc. Prof. Dr. Siriporn Daopiset King Mongkut’s University of
Technology North Bangkok
Asst. Prof. Dr. �anasan Intarakumthornchai King Mongkut’s
University of Technology North Bangkok
Asst. Prof. Dr. Yingyot Aueulan King Mongkut’s University of
Technology North Bangkok
Asst. Prof. Dr. Anak Khantachawana King Mongkut’s University of
Technology �onburi
Prof. Dr. Navadol Laosiripojana King Mongkut’s University of
Technology �onburi
Dr. Pongsak Tuengsook King Mongkut’s University o f Technology
�onburi
Asst. Prof. Dr. Sontipee Aimmanee King Mongkut’s University of
Technology �onburi
Dr. Chokchai Yatongchai Maejo UniversityProf. Dr. Banchong
Mahaisavariya, M.D. Mahidol UniversityAssoc. Prof. Dr. Chakrit
Sirisinha Mahidol UniversityAssoc. Prof. Dr. Norased Nasongkla
Mahidol UniversityAssoc. Prof. Dr. Panya Sunintaboon Mahidol
UniversityDr. Phornphop Naiyanetr Mahidol UniversityAsst. Prof. Dr.
Toemsak Srikhirin Mahidol UniversityAsst. Prof. Dr. Nutthita
Chuankrerkkul Metallurgy and Materials Science Research
Institute, Chulalongkorn UniversityProf. Dr. Rathanawan
Magaraphan Petroleum and Petrochemical College,
Chulalongkorn UniversityDr. Worawut Muangrat Shinshu
UniversityDr. Pichayen Bhothikhun Silpakorn UniversityAsst. Prof.
Dr. Nattakarn Hongsriphan Silpakorn University Sanamchandra
Palace
CampusAssoc. Prof. Dr. Pakorn Opaprakasit Sirindhorn
International Institute of
Technology, �ammasat UniversityAssoc. Prof. Dr.-Ing. Pornwasa
Wongpanya Suranaree University of TechnologyProf. Dr. Santi
Maensiri Suranaree University of TechnologyAsst. Prof. Dr. Sarum
Boonmee Suranaree University of TechnologyAsst. Prof. Dr. Sirirat
Tubsungnoen Rattanachan Suranaree University of TechnologyAsst.
Prof. Dr. Wimonlak Sutapun Suranaree University of TechnologyDr.
Pinai Mungsantisuk �ai Marine Protection Co., Ltd. Dr.
Siriporn Larpkiattaworn �ailand Institute of Scienti�c and
Technological ResearchAsst. Prof. Dr. Benya Cherdhirunkorn
�ammasat UniversityAssoc. Prof. Dr. Cattaleeya Pattamaprom �ammasat
UniversityDr. �anapol Tantisattayakul �ammasat UniversityAsst.
Prof. Dr. Weerachai Singhatanadgit, D.D.S �ammasat University
Assoc. Prof. Dr. Kulachate Pianthong Ubon Ratchathani
University
7
-
th
The 10th International Conference on Materials Science and
Technology
National Metal and Materials Technology Center
Mr. Amornsak Rengsomboon Dr. Pasaree LaokijcharoenDr. Anucha
Wannagon Ms. Patthamaporn TimakulDr. Asira Fuongfuchat Dr. Pawadee
Methacanon Dr. Atipong Malatip Dr. Pawnprapa PitakjakpipopDr.
Boonlom �avornyutikarn Dr. Pimpa Limthongkul Dr. Boonyawan Yoosuk
Dr. Pitak LaoratanakulDr. Bunpot Mai-ngam Dr. Pongdhorn Sae-ouiDr.
Chaiyuth Saekung Dr. Pornpimon BoonkumDr. Chakkrist
Phongphisutthinan Ms. Pranuda Jivaganont Dr. Chanchana
�anachayanont Dr. Prasert Chalermkarnnon Dr. Charinee Winotapun Dr.
Premrudee KanchanapiyaDr. Charusporn Mongkolkachit Dr. Samerkhae
JongthammanurakDr. Chaveewan Kongkaew Dr. Samunya SanguanpakDr.
Chureerat Prahsarn Dr. Sasitorn SrisawadiDr. Darunee Aussawasathien
Dr. Sinthu ChanthapanDr. Dhritti Tanprayoon Dr. Sirikarn
WisetsuwannaphumDr. Doungporn Sirikittikul Dr. Sitthisuntorn
SupothinaDr. Duangduen Atong Dr. Somboon OtarawannaDr. Ekkarut
Viyanit Dr. Somboon SahasithiwatDr. Jintamai Suwanprateeb Ms.
Somruethai Channasanon Dr. Kanit Soongprasit Dr. Sorachon YoriyaDr.
Kannaporn Pooput Dr. Sorayot ChinkanjanarotDr. Katanchalee Mai-ngam
Dr. Sumittra CharojrochkulDr. Kullachate Muangnapoh Dr. Supamas
Danwittayakul Dr. Narueporn Vaneesorn Dr. Supawan VichaphundDr.
Nirut Naksuk Dr. Surapich LoykulnantDr. Nispa Seetapan Dr. Sutee
OlarnrithinunDr. Nongnuch Poolsawad Dr. �anasat SooksimuangDr.
Noramon Intaranont Dr. �anya PhraewphiphatDr. Norrarat
Siribudhaiwan Ms. Umaporn Sanewirush Dr. Nudjarin Ramungul Dr.
Vituruch Goodwin Dr. Pacharapan Sonthithai Dr. Wanida
JanvikulDr. Pakamard Saewong Dr. Witchuda DaudDr. Panadda Sheppard
Dr. Worawarit Kobsiriphat Dr. Panjawat Kongsuwan Dr. Yatika
SomrangDr. Parjaree �avorniti Dr. Yotsakorn Pratumwal
8
-
The 10th International Conference on Materials Science and
Technology
September 6th-7th, 2018 BITEC, Bangkok, ThailandMaterials
Science and TechnologyMaterials Science and Technology
, 2018 BITEC, Bangkok, Thailand, 2018 BITEC, Bangkok,
Thailand
Organizers Co-organizers Platinum Sponsors
08:00-09:00
09:00-09:15
09:15-10:00
10:00-10:45
10:45-11:00 Break
Room GH201 MR221 MR222 MR223 MR224 MR225
Session
Dr. Danu PromminSession Chair (s)Dr. Somboon Otarawanna
and Dr. Sorayot Chinkanjanarot Dr. Yot Boontongkong Dr. Atitsa
PetchsukDr. Pitak Laoratanakul and
Asst.Prof.Dr. Oratai Jongprateep
11:00-11:15
11:15-11:30
11:30-11:45
11:45-12:00
����� �������������������
MRS-Thailand Annual Meeting(Closed Session)
Registration (2nd Floor in front of Grand Hall) and Poster Setup
(GH202 room, 2nd Floor)
Opening Ceremony (Grand Hall, 2nd Floor)
MRS Thailand
Biomedical Materials and Devices 1
Materials Technologyfor Environment 1
Ceramics 1(Advanced and
Electroceramics)Polymer 1Design & Manufacturing
and Computational Science & Engineering 1
BIO-O-01Wear Resistance of the Asian
Speci�c Knee-Joint ProsthesisKanokporn Pintobtang
DMC-I-01Hybrid Metal Forming
Processes for Mass Customized Production
Dr. Suwat Jirathearanat
ENV-I-01Metal Nanoparticle/Polymer/
Carbon Nanotube Hybrid Materials for Highly Sensitive and
Selective Volatile Organic
Compound DetectionDr. Worawut Muangrat
POL-I-01Functional Materials based on
Biodegradable Polylactide Copolymers: Form Synthesis to
Fabrication and ApplicationsAssoc.Prof.Dr. Pakorn
Opaprakasit
CER-I-01Local Structure Investigation in
some Magnetic MaterialsStudied by Synchrotron X-Ray
Absorption SpectroscopyAssoc.Prof.Dr. Rattikorn
Yimnirun
CER-O-01Phase Formation of Boron
Carbide PowderSynthesized from Glutinous
Rice FlourKannigar Dateraksa
CER-O-02Study of Electrical and Magnetic
Properties of Multiferroic Composite
(BiFeO3)x(Ba5TbTi3V7O30)1-x Hage Doley
POL-O-01Injection Moldable Poly(lactic
acid) (PLA)-Polybutylene Succinate (PBS)-Activated Carbon
Composite Foams: E�ects of PLA:PBS Ratios
Kittipong Hrimchum
POL-O-02Electro-Spinning and
Carbonisation of Lignin FibresBongkot Hararak
ENV-I-02Chiang Rai Zero Waste : A
Step-by-Step Approach toward Partnership for Sustainability
Dr. Panet Manomaivibool
BIO-O-02Design of Modular Proximal
Humeral Endoprosthesis based on Thai Anatomical DataKavin
Karunratanakul
BIO-O-03Fabrication of 3D Microstructure
with Superhydrophobic and Antifouling Properties for
Marine and Medical ApplicationsNithi Atthi
DMC-O-01Determination of Wrinkling
Initiation for Aluminum Alloy Sheet based on Instability
BehaviorChannarong Yamchoang
DMC-O-02Analysis and Correction of Defects for Deep Drawing
Process of Stainless Sink by Use of Finite Element
Simulation
Benjaphorn Khuanngern
PROG
RAM
Plenary Lecture 1: 3D Printing Materials Sciencesby Dr. Yinmin
(Morris) Wang, Materials Science Division, Lawrence Livermore
National Laboratory, USA
Plenary Lecture 2: State-of-the-Art Titanium Alloys by Powder
Metallurgy Processby Prof. Katsuyoshi Kondoh, Joining and Welding
Research Institute, Osaka University, Japan
Organizers Co-organizers Platinum Sponsors
9
-
Session MRS Thailand
Dr.Wallop RatanathavornDr. Lada Punsukumtana
and Dr. Anucha Wannagon
13:00-13:15
13:15-13:30
13:30-13:45
13:45-14:00
14:00-14:15
14:15-14:30
14:30-14:45
14:45-15:00 Break Break
Dr. Yot Boontongkong
Materials Technologyfor Environment 2
Innovative Textiles for Future Healthcare Appli-
cation
Ceramics 2(Glass Science &
Technology)
Dr. Somboon Otarawanna and Dr. Sorayot Chinkanjanarot
Design & Manufacturing and Computational
Science & Engineering 2
Metals, Alloys & Intermetallic
Compounds 1
MET-I-01Future Manufacturing
Now – SLM Solutions at a glance: SLM Technology,
Applications, Additive Intelli-gence and R&DDr. Edwin
Mok
MET-O-01Surface Smoothing by Friction Stir Forming for A5083
Alumi-
num Alloy PlateTakahiro Ohashi
MET-O-02Spheroidization of
Fe-intermetallic Compounds in Al-Si Alloys
by Ultrasonic VibrationChakkrist Phongphisutthinan
MET-O-03Isothermal Aging of Al-Ni-Sc
Alloy containing Al3Ni Micro�bers and Al3Sc
NanoprecipitatesChanun Suwanpreecha
MET-O-04Synthesis of Al-Li Alloys by
Hybrid Semi-Solid and Sonication Processing
Payodhar Padhi
MET-O-05In�uence of Magnesium on
Microstructures and Mechanical Properties of
Cu-38Zn-1Sn-0.2Al-0.2Si AlloysPemika Suksongkarm
DMC-I-02CFD Simulation and Modeling
of Metallurgical ProcessesAsst.Prof.Dr.-Ing. Pruet
Kowitwarangkul
ENV-O-01In�uence of Silica Supports on
Photocatalytic Oxidation of Sulfur Compound and Sulfone
AdsorptionNitipon Chekuntod
CER-O-03E�ect of Barium Addition on
the Glass Structure of Na-Si-Al-Ca-Zn Glaze System
Niti Yongvanich
CER-O-04E�ect of Alumina on Mechanical
Properties of Glass Fiber from Basalt and Bottom Ash Mixture
Apirat Theerpapvisetpong
CER-O-05E�ect SiO2 Contents in
TEOS-SiO2-OTES Hybrid Coating on Glass
Kanit Tapasa
CER-O-06Study of Crystal Structure and
Topography of Sintered Glass-Ceramic
Produce from NBS and SLG Nattawat Kulrata
CER-O-07Preparation of Lightweight Brick
from Waste Glass and Lime Mud
Piyanan Boonphayak
Registration(In front of MR 224)
TEX-I-01Multifunctionality in
Textiles using Metal-organic Frameworks
Prof. Juan P Hinestroza
(14:15-15:15)TEX-I-02
Smart Textiles having Sensors and Actuators to
help Human ActivityProf. Mutsumi Kimura
ENV-O-03Enhancing the Photocatalytic
Degradation of TiO2 over Pineapple Fibers Material for
Methyleneblue RemovalSuchadee Sribenja
ENV-O-04Bamboo Char-supported
Platinum Nanoparticle Electrocatalyst for the Oxygen
Reduction ReactionSamerkhae Jongthammanurak
ENV-O-05E�ect of Surfactant on Collapse in Oil Palm Wood during
Drying
Choosak Rittiphet
ENV-O-06Optical Transparent and
Hydrophobic Properties of TEOS/OTES Hybrid Materials by
Sol-Gel ProcessingUsanee Pantulap
ENV-O-07Glass Batch Modi�cation to
Improve The Weathering Resistance in Soda-lime
Silicate GlassEkarat Meechoowas
ENV-O-08Mechanical Properties and
Thermal Performance of Autoclaved Aerated Lightweight
Concrete Wall Consisting of Phase Change Material
Aitthi Khongthon
DMC-O-03Bending Limit Curves in Strain and Stress Space for
Advanced
High Strength Steel Sheet Phimmat Kalawong
DMC-O-04 In�uence of Pre-Stretching mode on the Forming
Limit
Strain and Stress Diagrams of High Strength Steel Sheet
Korkiat Laokor
DMC-O-05In�uence of Pre-Stretching on
Fracture Forming Limit Curve of Aluminum Alloys Sheet
AA5052-H32Taratip Chaimongkon
DMC-O-08Fatigue Assessment of an
O�shore Piping System by Finite Element Analysis
Somboon Otarawanna
DMC-O-09Investigation of the Structural Integrity of a Cryogenic
Tank with Sunken Marks by Finite
Element AnalysisSomboon Otarawanna
12:00-13:00 Lunch (GH203 room, 2nd Floor)
Session Chair (s)
MRS-Thailand Annual Meeting
10
-
Session MRS Thailand
Dr. Sinthu ChanthapanAsst.Prof.Dr.-Ing. Pruet
Kowitwarangkul Dr. Pakamard SaewongDr. Supawan Vichaphund
and
Asst.Prof.Dr. Niti Yongvanich
15:00-15:15
15:15-15:30 Break
15:30-15:45
15:45-16:00
16:00-16:15
16:15-16:30
16:30-18:00 Poster Session I (GH202 room, 2nd Floor)
18:00-20:00 Banquet (Fahrenheit Restaurant, 1st Floor)
Materials Technologyfor Environment 3
Ceramics 3(Ceramic Materials for
Energy and Environmental Applications)
Design & Manufacturing and Computational
Science & Engineering 3
Metals, Alloys & Intermetallic
Compounds 2
MET-I-02A Microstructure Based Design for Applications of
Advanced
High Strength SteelsAssoc. Prof. Dr.-Ing Vitoon
Uthaisangsuk
DMC-O-06Ductility Improvement of the
Co-28Cr-6Mo Alloy Processed by Selective Laser Melting
Pongnarin Jiamwatthanachai
ENV-O-09Incorporating Black Dust into Autoclaved Aerated
Concrete
Wall for Heat Transfer ReductionKetwadee Janyoosuk
CER-I-02Challenges in Application of
Ceramic Materials for Sustainable Water Treatment and
Wastewater
RecyclingAssoc. Prof. Dr. Chavalit
Ratanatamskul
CER-O-09Preparation of Porous Alumina
Refractory Brick by Addition of Foaming Agent
Thanakorn Wasanapiarnpong
CER-O-10E�ect of Zeolite on Early
Strength of Portland Cement Mortars
Raphat Tanasalagula
CER-O-11Preparation of Lightweight
Clay Brick by Additions of Plaster Mold Waste,
Sodium Silicate and Foaming Agent
Thanakorn Wasanapiarnpong
ENV-O-10In�uence of Type and
Composition of SCM on Expansion of Mortar Bars
from
Alkali -Silica ReactionSuvimol Sujjavanich
ENV-O-11Impact of Engine Oil's Additives
on Particulate Matter's Micro- and Nanostructure using
Electron Microscopy Image Analysis
Phyo Zin Ko Ko Discussion Panel
Textiles 4.0: Innovation and Market Trend
in Well-being Society
Panelists:Peerawat Thongkam
Novatec Healthcare Co., Ltd.
Sutee Tappong Thong Thai Textile Co., Ltd.
Sirinan Thubthimthed Thailand Institute of Scienti�c and
Technological Research
Moderator: Dr. Jarika Makkoch
Imagine Innovation Co., Ltd.
DMC-O-07Application of MATLAB GUI for
Modeling of Residual Stress and Distortion in Arc Welded
Metal
Kittichai Sojiphan
DMC-O-10Study Under�ow Diameter,
Vortex �nder, Cylindrical and Conical Lengths of
Hydrocyclone to achieve High Separation SharpnessSupachart
Pakpoom
DMC-O-11The Quality Improvement of Molten Aluminium Alloy in
Melting and Casting ProcessJintana Tempiamwatcharothai
DMC-O-12Determination of Internal and
External Surface Areas of Atomistic
Porous Carbons Poomiwat Phadungbut
MET-O-06Corrosion Behaviors of Ship Structural Steel in
Simulated
Marine Tidal EnvironmentNattapol Jaiyos
MET-O-07Metallurgical Evaluation
of 304H Coil for Cracking Furnace
Siriwan Ouampan
MET-O-08E�ect of Substrate-Target
Distance on the Structure of TiCrN Films Deposited from
Mosaic Target by Reactive DC Magnetron Sputtering
Nirun Witit-Anun
MET-O-09One Step Pressing-Annealing to
Produce LTP MnBi MagnetsThanida Charoensuk
Innovative Textiles for Future Healthcare
Application(Cont.)
Session Chair (s)
MRS-Thailand Annual Meeting
11
-
08:00-09:15
09:15-10:00
10:00-10:45
10:45-11:00 Break
Room GH201 MR221 MR222 MR223 MR224 MR225
Session
Dr. Vituruch Goodwin Dr. Dhritti Tanprayoon Dr. Robert MolloyDr.
Chanchana
Thanachayanont Assoc.Prof.Dr. Ittipol
Jangchud
Asst.Prof.Dr. Sirithan Jiemsirilers and
Dr. Charusporn Mongkolkachit
11:00-11:30
11:30-11:45
11:45-12:00
12:00-13:00
������ �������������������
Materials for Energy 1 Metals, Alloys & Intermetallic
Compounds 3
Biomedical Materials and Devices 2
Testing and Reliability 1 Polymer 2
ENR-I-01Lithium-ion Battery:
Material and System Design towards High Rate Capability
Dr. Pimpa Limthongkul
MET-I-03Microstructure Formation of
Solder Alloys During Soldering Using Synchrotron
Radiography ImagingDr. Mohd Arif Anuar
Mohd Salleh
BIO-I-01Stereo lithographic Additive
Manufacturing of Bio-Ceramic Implants with Graded and
Fluctuated StructuresProf. Soshu Kirihara
TES-I-01Understanding Nanostructures
and Nanostructure Development using X-ray
and Complementary Spectroscopic Techniques
Prof. Lam Yeng Ming
POL-I-02Superior Tough Polymers:
Recent Advances in Polymer Processing
Prof.Dr.Eng. Hiroshi Ito
CER-I-03Processing and Properties of Ceramic Geopolymer
Based
MaterialsAssoc. Prof. Dr. Mohd Mustafa Al
Bakri Abdullah
CER-O-12Fly Ash-Based Geopolymer:
Fabrication and Applications Patthamaporn Timakul
CER-O-13Cenospheres Separation from
Lignite Fly AshSorachon Yoriya
POL-O-03Stretchable and Ultrasensitive
Strain and/or Self-sensing Material Based on Carbon
Nanostructures-polymer
NanocompositesTejendra Kumar Gupta
POL-O-04Formation of Porous Polymer Nanostructures by
Imprinting
Process: Phase Separation and Foaming of PS/PVA Blend
at the NanoscaleParitat Muanchan
TES-I-02XPS and XAS for
Characterization of Carbon Materials
Assoc.Prof.Dr. Prayoon Songsiriritthigul
BIO-I-02Tissue Intergrated 3DP Porous
Polyethylene ImplantDr. Jintamai Suwanprateeb
MET-O-10E�ects of Admixed Ni, B and C
Elements on Microstructure and Property of Sintered Steels
Bhanu Vetayanugul
MET-O-11Microstructure, Mechanical and
Wear Properties of Sintered Fe-Mo-Si-C Alloys
Kittikhun Ruangchai
ENR-O-01Decreasing Precipitation in
Biodiesel Blending with Fossil Diesel by Using Partial
HydrogenationUkrit Sahapatsombut
ENR-O-02E�ect of SiO2 Pore Size on
Sulfur Tolerance of Metallic Catalysts used for Partial
Hydrogenation of BiodieselTheerapron Leung-On
Registration (2nd Floor in front of Grand Hall)
Plenary Lecture 4: Next Generation Rechargeable Batteriesby
Prof. Takeshi Abe, Kyoto University, Japan
Ceramics 4(Geopolymers, Cements, and
Conventional Ceramics)
Lunch (GH203 room, 2nd Floor)
Plenary Lecture 3: Ceramics Manufacturing by Spark Plasma
Sinteringby Prof. Takashi Goto, Tohoku University, Japan and Wuhan
University of Technology, China
Session Chair (s)
12
-
Session
Dr. Worawarit Kobsiriphat Bhanu VetayanugulAsst.Prof.Dr.
Weerachai
Singhatanadgit Dr. Bralee Chayasombat Dr. Witchuda Daud
13:00-13:15
13:15-13:30
13:30-13:45
13:45-14:00
14:00-14:15
14:15-14:45 Break & Poster Session II (GH202 room, 2nd
Floor)
ENR-O-03The In�uence of Precursors on Optical Properties of
Carbon
Nanodots Synthesized via Hydrothermal Carbonization
TechniqueKamonwan Aup-Ngoen
MET-O-12Mechanical and Wear Properties
of Pearlitic Ductile Iron-like Sintered Fe-Cr-Mo-Si-C Alloys
Kittikhun Ruangchai
BIO-O-05Strontium Containing Sol-Gel Bioactive Glass
Nanoparticles (Sr-BGNPs) for Bone Regeneration
ApplicationsParichart Naruphontjirakul
POL-O-05Oxygen Permeability
Enhancement of Commercial Polyethylene Terephthalate/
Polyethylene Laminated Film by Laser Micro-Perforation
Technique; Modi�ed Atmosphere Packaging
for Ready to Eat Fresh-Cut Ajcharaporn Aontee
CER-I-04Solid-state Synthesis of
NIR-re�ective Black Pigment: E�ect of Raw Material on
Pigment’s PropertyDr. Sitthisuntorn Supothina
CER-O-14Double Ceramic Layer Thermal
Barrier Coating (DCL-TBC) Architecture : An Overview
Azrina Arshad
CER-O-15Workability and Setting Time
of Superplasticizers on Alkaline-Activated
Class C Fly AshKhanthima Hemra
POL-O-06A Comparison of Microhole
Formation Behavior on Polypropylene and Poly(lactic
acid) Film Using CO2 Laser Irradiation
Charinee Winotapun
POL-O-07Enhancement of Cellular
Structure and Properties of Flame Retardant Insulation
Polyethylene Octene Elastomer (POE) Foam by Blending with
Natural RubberKarnjana Sawangpet
POL-O-08The Stress-strain Extraction of
Rubber-foam Material by using Arti�cial Neural Network and
Genetic AlgorithmEkachai Ouysook
TES-I-03Applications of
Synchrotron-based X-ray Absorption Spectroscopy and
Infrared Microscopy to Investigate on Advanced
Functional MaterialsDr. Pinit Kidkhunthod
TES-O-01Application of Ultrasonic
Inspection for Microstructure Analysis of Metals Kittichai
Sojiphan
TES-O-02A Barkhausen Noise Measuring
System for Steel Hardness Evaluation
Nopparat Seemuang
MET-O-13In�uences of Cooling Rate
and Carbon Content on Microstructures, Mechanical
and Wear Properties of Sintered Fe-Mo-C Steels
Monnapas Morakotjinda
BIO-O-06Association between Extracellular Matrix
Accumulation and Oxidative Stress-induced Apoptosis in
Chondrocytes Cultured on
3D-porous Sca�olds in Static versus Dynamic Cultures
Tareerat Lertwimol
MET-O-14E�ect of Boron Addition and
Sintering Atmosphere on Precipitation in Sintered
Fe-Mo-C SteelsNattaya Tosangthum
BIO-O-07Radiation Processing of
Hydrogel Sheet Dressings Incorporated with Antibacterial
Properties for Wound Healing
ApplicationPimpon Uttayarat
MET-O-15Thermoelectric Properties of Lead Telluride
Processed by
Mechanical Grinding and Hot-Pressing Technique Mongkol
Bumrungpon
BIO-O-08Preparation of 3D-Printed
Oligolactide-Hydroxyapatite Composite Sca�olds Loaded
with Bone Morphogenetic Protein-2 for Bone Tissue
EngineeringJitlada Sansatsadeekul
BIO-O-04Shear Bond Strength of Resin
Cement to Saliva-contaminated Metal Alloys After Various
Surface TreatmentsAtikom Surintanasarn
ENR-O-04E�ects of Cr Doping into Mn-site on Physical and
Electrochemical Properties of Li2MnSiO4 Cathode Materials
for Li-ion BatteriesThanya Phraewphiphat
ENR-O-05Synthesis and Characterizations
of a Family of Dual-functional Lithium Salts
for Lithium-Polymer BatteriesPriew Eiamlamai
ENR-O-06Electrophoretic Deposition of Carbon Nanotubes onto
Metal
Substrates: Characterization and Electrochemical
Applications
Napapon Massa-Angkul
Materials for Energy 2Metals, Alloys &
Intermetallic Compounds 4
Biomedical Materials and Devices 3
Testing and Reliability 2 Polymer 3
Ceramics 5(Novel Synthesis and
Coating)Dr. Kullachate Muangnapoh and
Dr. Siriporn LarpkiattawornSession Chair (s)
13
-
SessionPolymers 4
Dr. Ukrit Sahapatsombut Bhanu Vetayanugul Dr. Nutthanun
Suphadon
14:45-15:00
15:00-15:15
15:15:15:30
15:30-15:45
15:45-16 :00
16 :00-16 :30 Closing Ceremony (Grand Hall, 2nd Floor)
ENR-O-07Carbon for Anode Materials from
Rice Husk and Rice StrawPranuda Jivaganont
Materials for Energy 3 Metals, Alloys & Intermetallic
Compounds 5
Biomedical Materials and Devices 4
Testing and Reliability 3
Ceramics 6(Novel Synthesis and
Coating)
Dr. ChanchanaThanachayanont
Asst. Prof. Dr. Dujreutai Pongkao Kashima
Asst.Prof.Dr. Thanakorn Wasanapiarnpong and
Dr. Samunya Sanguanpak
ENR-O-083,12-Bis(phenylmethylamine)-[i]-
(1-phenyl-pyrrolidine-2,5-diono)-[5]helicene:
A New Semiconductor Material for Organic Electronic
ApplicationsLaongdao Kangkaew
ENR-O-09A Novel Red Dye from
[5] Helicene Derivative for Organic Light-Emitting Diode
Waraporn Panchan
ENR-O-10Solution Processable
Molybdenum Oxide as a Hole Transport Layer for Organic
Photovoltaic DevicesChaiyuth Saekung
MET-O-16Microstructure and Property of
Sintered Fe-4Ni-0.5-Mo-0.14Mn-0.22B-xC Steels
Thanyaporn Yotkaew
MET-O-17E�ect of Waste-Derived Calcium
Sulfate Additions on the Tribological Properties of
Sintered Steel-Based MaterialChiraporn Auechalitanukul
MET-O-18Tribological Properties of Sintered Graphite-Steel
Composites Containing Lignite Bottom Ash
Chiraporn Auechalitanukul
BIO-O-09Dual-curing Polylactide for Resorbable Bone Cement
Somruethai Channasanon
BIO-O-10Multifunctional Properties of
Mineral Ions Incorporated Hydroxyapatite/Chi-g-PMMA
Sca�old for Bone Tissue Engineering
Tanatsaparn Tithito
BIO-O-11E�ect of pH on Resorbability of 3D Printed
Hydroxyapatite
Faungchat Thammarakcharoen
BIO-O-12E�ect of Yttria-stabilized Zirconia
Addition on Mica-based Glass-ceramic
Sukanda Angkulpipat
BIO-O-13E�ect of Pre-reaction Glass on
Strength of Glass Ionomer Cement as a Dental Filler
Autcharaporn Srion
TES-O-04A Study of Size and Surface
Measurement of Nanoparticles and Mesoporous Materials and
Interlaboratory ComparisonBralee Chayasombat
TES-O-05Failure Analysis of Superheat Tube 2.5Cr-1Mo in
Biomass
Power PlantBoonhlua Khwansri
TES-O-06X-Ray and Computed
Tomography as a Tool for Quality Assurance, Process
Optimization
and Material Characterization in the Field of Additive
ManufacturingPhilip Sperling
POL-I-03Natural Rubber (NR) in Rail and
Agriculture Applications : Rubber Rail Crossing Panels and
Reinforced Porous PipesAssoc.Prof.Dr. Ittipol Jangchud
POL-O-09Strain-induced Crystallization of Natural
Rubber/Halloysite
Nanotubes Composites in the Presence of Alkanolamide-based
Palm StearinNureeyah Jehsoh
POL-O-10Novel Thermoplastic
Vulcanizates based on Polyamide-12 Blends: In�uence
of Modi�ed Devulcanized Natural Rubber Gloves on Properties of
the BlendsBoripat Sripornsawat
POL-O-11In�uence of Filler Network
Formation on De-vulcanization E�ciency of Carbon Black
Filled
SBR and NRAnuwat Worlee
CER-I-05Polydiacetylene/Zinc oxide
Nanocomposites for Colorimetric Sensing
ApplicationsAssoc.Prof.Dr. Nisanart Triphol
CER-O-17In�uences of Chemical
Composition, Microstructure and Bandgap energy no
Photocatalytic Activities of ZnO and Ag-doped ZnO by
Solution
Combustion Technique Kornkamon Meesombad
Session Chair (s)
14
-
th
The 10th International Conference on Materials Science and
Technology
BIO Biomedical Materials and Devices [ BIO-P-01 to BIO-P-10
]
CER Ceramics[ CER-P-01 to CER-P-32 ]
DMC Design and Manufacturing + Computational Science and
Engineering [ DMC-P-01 ]
ENR Materials for Energy[ ENR-P-04 to ENR-P-14 ]
ENV Materials Technology for Environment [ ENV-P-01 to ENV-P-18
]
MET Metals, Alloys and Intermetallic Compounds [ MET-P-01 to
MET-P-16 ]
POL Polymers[ POL-P-01 to POL-P-26 ]
TES Testing and Reliability [ TES-P-01 to TES-P-02 ]
MR225
MR224
GH 201 GH 202 GH 203
MR223
MR210
MR222
MR221
Poster RoomGrand Hall Lunch Room
Stage
GH 202Poster Room
Foyer AreaExhibition Zone
Registration
www.mtec.or.th/msat-10
1 2 3 4 5 6 7 8
15 14 13 12 11 10 9
Refreshment
MTEC
1 RI Technologies Ltd. 2 – 4 Department of Materials Science
and
Engineering, Silpakorn University5 Plastics Institute of
Thailand6 Thai Parkerizing Co., Ltd.7 – 8 IRPC Public Company
Limited9 – 10 Photonics Science Co., Ltd. 11 Metallurgy and
Materials Science Research
Institute, Chulalongkorn University12 Materials Research Society
of Thailand13 Adtech Service Automation Co., Ltd. 14 Kinetics
Corporation Ltd.15 Bara Scienti�c Co., Ltd.16 Puditec Co., Ltd.
Foyer AreaExhibition
16
15
-
th
The 10th International Conference on Materials Science and
Technology
LIST OF ORAL & POSTER PRESENTATIONS
PLENARY LECTURESPL-01 3D Printing Materials Sciences PL-01
Yinmin WangPL-01 Lawrence Livermore National Laboratory, United
State of America PL-02 State-of-The-Art Titanium Alloys by Powder
Metallurgy ProcessPL-02 Katsuyoshi KondohPL-02 Osaka University,
Japan PL-03 Ceramics Manufacturing by Spark Plasma Sintering PL-03
Takashi GotoPL-03 Tohoku University, Japan PL-04 Next Generation
Rechargeable BatteriesPL-04 Takeshi AbePL-04 Kyoto University,
Japan
BIOMEDICAL MATERIALS AND DEVICESINVITED LECTURES
BIO-I-01 Stereolithographic Additive Manufacturing of
Bio-Ceramic Implants with Graded and Fluctuated Structures
BIO-I-01 Soshu KiriharaBIO-I-01 Osaka University, Japan BIO-I-02
Tissue Intergrated 3DP Porous Polyethylene ImplantBIO-I-02 Jintamai
SuwanprateebBIO-I-02 National Metal and Materials Technology Center
(MTEC), Thailand
ORAL PRESENTATIONSBIO-O-01 Wear Resistance of the Asian Specific
Knee-Joint ProsthesisBIO-O-01 Kanokporn PintobtangBIO-O-01 National
Metal and Materials Technology Center (MTEC), Thailand BIO-O-02
Design of Modular Proximal Humeral Endoprosthesis Based on Thai
Anatomical Data BIO-O-02 Kavin KarunratanakulBIO-O-02 National
Metal and Materials Technology Center (MTEC), Thailand BIO-O-03
Fabrication of 3D Microstructure with Superhydrophobic and
Antifouling Properties for
Marine and Medical Applications BIO-O-03 Nithi AtthiBIO-O-03
National Electronics and Computer Technology Center (NECTEC),
Thailand BIO-O-04 Shear Bond Strength of Resin Cement to
Saliva-contaminated Metal Alloys After Various
Surface TreatmentsBIO-O-04 Atikom SurintanasarnBIO-O-04
Chulalongkorn University, Thailand BIO-O-05 Strontium Containing
Sol-Gel Bioactive Glass Nanoparticles (Sr-BGNPs) for Bone
Regeneration ApplicationsBIO-O-05 Parichart
NaruphontjirakulBIO-O-05 King Mongkut's University of Technology
Thonburi, Thailand BIO-O-06 Association between Extracellular
Matrix Accumulation and Oxidative Stress-induced
Apoptosis in Chondrocytes Cultured on 3D-porous Scaffolds in
Static versus Dynamic Cultures
BIO-O-06 Tareerat LertwimolBIO-O-06 National Metal and Materials
Technology Center (MTEC), Thailand
16
-
th
The 10th International Conference on Materials Science and
Technology
BIO-O-07 Radiation Processing of Hydrogel Sheet Dressings
Incorporated with Antibacterial Properties for Wound Healing
Application
BIO-O-07 Pimpon UttayaratBIO-O-07 Thailand Institute of Nuclear
Technology, Thailand BIO-O-08 Preparation of 3D-Printed
Oligolactide-Hydroxyapatite Composite Scaffolds Loaded with
Bone Morphogenetic Protein-2 for Bone Tissue EngineeringBIO-O-08
Jitlada SansatsadeekulBIO-O-08 National Metal and Materials
Technology Center (MTEC), Thailand BIO-O-09 Dual-curing Polylactide
for Resorbable Bone CementBIO-O-09 Somruethai ChannasanonBIO-O-09
National Metal and Materials Technology Center (MTEC), Thailand
BIO-O-10 Multifunctional Properties of Mineral Ions Incorporated
Hydroxyapatite/Chi-g-PMMA
Scaffold for Bone Tissue EngineeringBIO-O-10 Tanatsaparn
TithitoBIO-O-10 Kasetsart University, Thailand BIO-O-11 Effect of
pH on Resorbability of 3D Printed HydroxyapatiteBIO-O-11 Faungchat
ThammarakcharoenBIO-O-11 National Metal and Materials Technology
Center (MTEC), Thailand BIO-O-12 Effect of Yttria-stabilized
Zirconia Addition on Mica-based Glass-ceramicBIO-O-12 Sukanda
AngkulpipatBIO-O-12 Kasetsart University, Thailand BIO-O-13 Effect
of Pre-reaction Glass on Strength of Glass Ionomer Cement as a
Dental FillerBIO-O-13 Autcharaporn SrionBIO-O-13 National Metal and
Materials Technology Center (MTEC), Thailand
POSTER PRESENTATIONSBIO-P-01 A Study of Sericin-Thunbergia
Laurifollia Electrospun Fibre for Wound Healing ApplicationBIO-P-01
Pattarinee KlumdoungBIO-P-01 Rajamangala University of Technology
Krungthep, Thailand BIO-P-02 Bacterial Cellulose Microcrystal for
Medical Materials: Part II BIO-P-02 Pornpen SiridamrongBIO-P-02
Thailand Institute of Scientific and Technological Research,
Thailand BIO-P-03 Influence of Thermal Treatment Temperature on
Phase Formation and Bioactivity of Glass-
Ceramics Based on the SiO2-Na2O-CaO-P2O5 System BIO-P-03
Nuttapon PisitpipathsinBIO-P-03 Rajamangala University of
Technology Isan, Thailand BIO-P-04 Preparation and Evaluation of
Electrospun Fibers Containing Antibiotic Tetracycline BIO-P-04
Manisara PhiriyawirutBIO-P-04 King Mongkut's University of
Technology Thonburi, Thailand BIO-P-05 Effect of Ferroelectric BCZT
Materials Addition on Bioactive Behavior of 45S5/xBCZT
CompositesBIO-P-05 Nuttapon PisitpipathsinBIO-P-05 Rajamangala
University of Technology Isan, Thailand BIO-P-06 Preparation of
Semi-interpenetrating Polymer Network Hydrogels from Silk Sericin
for
Wound Healing Treatment BIO-P-06 Supattra KlayyaBIO-P-06 Mae Fah
Luang University, Thailand BIO-P-07 Water Absorption and Granular
Agglomeration of 3D Printed Hydroxyapatite Granules BIO-P-07
Faungchat ThammarakcharoenBIO-P-07 National Metal and Materials
Technology Center (MTEC), Thailand BIO-P-08 Effects of Surface
Modification Processes on the Adhesion of Hydroxyapatite Layers
Coated
onto Titanium SubstratesBIO-P-08 Benjaporn InseemeesakBIO-P-08
Kasetsart University, Thailand
17
-
th
The 10th International Conference on Materials Science and
Technology
BIO-P-09 Development of In Situ Cross-Linking Hydrogel from
Sodium Alginate/ Banana Peel Polysaccharides and Calcium Carbonate
for Biomedical Applications
BIO-P-09 Saranyou OontaweeBIO-P-09 Thammasat University,
Thailand BIO-P-10 Effect of Heat Treatment on Properties of Calcium
Phosphate CementBIO-P-10 Kannaporn PooputBIO-P-10 National Metal
and Materials Technology Center (MTEC), Thailand
CERAMICSINVITED LECTURES
CER-I-01 Local Structure Investigation in Some Magnetic
Materials Studied by Synchrotron X-Ray Absorption Spectroscopy
CER-I-01 Rattikorn YimnirunCER-I-01 Vidyasirimedhi Institute of
Science and Technology, Thailand CER-I-02 Challenges in Application
of Ceramic Materials for Sustainable Water Treatment and
Wastewater Recycling CER-I-02 Chavalit RatanatamskulCER-I-02
Chulalongkorn University, Thailand CER-I-03 Processing and
Properties of Ceramic Geopolymer Based MaterialsCER-I-03 Mohd
Mustafa Al Bakri AbdullahCER-I-03 Universiti Malaysia Perlis
(UniMAP), Malaysia CER-I-04 Solid-state Synthesis of NIR-reflective
Black Pigment: Effect of Raw Material on Pigment’s
PropertyCER-I-04 Sitthisuntorn SupothinaCER-I-04 National Metal
and Materials Technology Center (MTEC), Thailand CER-I-05
Polydiacetylene/Zinc Oxide Nanocomposites for Colorimetric Sensing
Applications CER-I-05 Nisanart TraipholCER-I-05 Chulalongkorn
University, Thailand
ORAL PRESENTATIONSCER-O-01 Phase Formation of Boron Carbide
Powder Synthesized from Glutinous Rice FlourCER-O-01 Kannigar
DateraksaCER-O-01 Chulalongkorn University, Thailand CER-O-02 Study
of Electrical and Magnetic Properties of Multiferroic Composite
(BiFeO3)x(Ba5TbTi3V7O30)1-x CER-O-02 Hage DoleyCER-O-02 Rajiv
Gandhi University, India CER-O-03 Effect of Barium Addition on the
Glass Structure of Na-Si-Al-Ca-Zn Glaze System CER-O-03 Niti
YongvanichCER-O-03 Silpakorn University, Thailand CER-O-04 Effect
of Alumina on Mechanical Properties of Glass Fiber from Basalt and
Bottom Ash MixtureCER-O-04 Apirat TheerapapvisetpongCER-O-04
Chulalongkorn University, Thailand CER-O-05 Effect SiO2 Contents in
TEOS-SiO2-OTES Hybrid Coating on Glass CER-O-05 Kanit
TapasaCER-O-05 Department of Science Service, Thailand CER-O-06
Study of Crystal Structure and Topography of Sintered Glass-Ceramic
Produce from
NBS and SLGCER-O-06 Nattawat KulratCER-O-06 Mahidol University,
Thailand CER-O-07 Preparation of Lightweight Brick from Waste Glass
and Lime MudCER-O-07 Piyanan BoonphayakCER-O-07 Naresuan
University, Thailand
18
-
th
The 10th International Conference on Materials Science and
Technology
CER-O-09 Preparation of Porous Alumina Refractory Brick by
Addition of Foaming AgentCER-O-09 Thanakorn WasanapiarnpongCER-O-09
Chulalongkorn University, Thailand CER-O-10 Effect of Zeolite on
Early Strength of Portland Cement MortarsCER-O-10 Raphat
TanasangulCER-O-10 Kasetsart University, Thailand CER-O-11
Preparation of Lightweight Clay Brick by Additions of Plaster Mold
Waste, Sodium Silicate
and Foaming AgentCER-O-11 Thanakorn WasanapiarnpongCER-O-11
Chulalongkorn University, Thailand CER-O-12 Fly Ash-Based
Geopolymer: Fabrication and Applications CER-O-12 Patthamaporn
TimakulCER-O-12 National Metal and Materials Technology Center
(MTEC), Thailand CER-O-13 Cenospheres Separation from Lignite Fly
Ash CER-O-13 Sorachon YoriyaCER-O-13 National Metal and Materials
Technology Center (MTEC), Thailand CER-O-14 Double Ceramic Layer
Thermal Barrier Coatings (DCL-TBCs) Architecture : an Overview
CER-O-14 Azrina ArshadCER-O-14 Universiti Teknologi Malaysia,
Malaysia CER-O-15 Workability and Setting Time of Superplasticizers
on Alkaline-Activated Class C Fly Ash CER-O-15 Khanthima
HemraCER-O-15 National Metal and Materials Technology Center
(MTEC), Thailand CER-O-17 Influences of Chemical Composition,
Microstructure and Bandgap Energy No Photocatalytic
Activities of ZnO and Ag-doped ZnO by Solution Combustion
Technique CER-O-17 Kornkamon MeesombadCER-O-17 Kasetsart
University, Thailand
POSTER PRESENTATIONSCER-P-01 Effect of ZrO2 and MgO Addition on
Structure, Mechanical and Thermal Properties of
Metakaolin-Based Geopolymer ProductsCER-P-01 Rewadee
WongmaneerungCER-P-01 Maejo University, Thailand CER-P-02 Effect of
Ferric Oxide Nanoparticles Incorporation on Structure and
Electrical Properties of
Modified BNKT Lead-Free CeramicsCER-P-02 Pharatree JaitaCER-P-02
Chiang Mai University, Thailand CER-P-03 Mechanical and Electrical
Properties of BZT Modified by Barium Hexaferrite CER-P-03 Supalak
ManothamCER-P-03 Chiang Mai University, Thailand CER-P-04
Temperature Dependence on Mechanical, Dielectric and Electric
Field-Induced Strain
Response of Lead-Free BSrT-Modified BNKT Ceramics CER-P-04
Pharatree JaitaCER-P-04 Chiang Mai University, Thailand CER-P-05
The Effects of Replacement Metakaolin with Diatomite in Geopolymer
Ceramic MaterialsCER-P-05 Suwanan ThammarongCER-P-05 Chiang Mai
University, Thailand CER-P-06 Utilization of Lignite Ash as Raw
Materials for Ceramic Tile PreparationCER-P-06 Mateekul
JiarawattananonCER-P-06 National Metal and Materials Technology
Center (MTEC), Thailand CER-P-07 Influence of Mechanical Activation
on the Phase Formation in the Synthesis of Cordierite
from Talc and Andalusite CER-P-07 Chatcharin
VairojanakitCER-P-07 Chulalongkorn University, Thailand
19
-
th
The 10th International Conference on Materials Science and
Technology
CER-P-08 Antibacterial Activity of Silver Exchanged Zeolite:
Effect of Si/Al Ratio on Zeolite Framework
CER-P-08 Nissapa WattanawongCER-P-08 Chulalongkorn University,
Thailand CER-P-09 Characteristic and Preparation of TiO2/PVP
Nanofiber using Electrospinning Technique CER-P-09 Tawat
SoitongCER-P-09 Maejo University, Thailand CER-P-10 Mechanical and
Electrical Properties of La Modified
Bi0.5(Na0.4K0.1)(Ti0.98Zr0.02)O3 CeramicsCER-P-10 Pichitchai
ButnoiCER-P-10 Chiang Mai University, Thailand CER-P-11 Effects of
Bituminous Coal Ash Addition in Pottery ProductsCER-P-11 Yannawut
WonghomCER-P-11 Chulalongkorn University, Thailand CER-P-12
Reducing Water Absorption of Fiber-Cement Composites for Exterior
Applications by Crystal
Modification Method CER-P-12 Parinya ChakartnarodomCER-P-12
Kasetsart University, Thailand CER-P-13 Effect of Pore Formers on
Anode Pore Structure and Electrochemical Performance of Solid
Oxide Fuel Cell CER-P-13 Nutthita ChuankrerkkulCER-P-13
Metallurgy and Materials Science Research Institute, Thailand
CER-P-14 Fabrication of Li0.06(K0.5,Na0.5)0.94NbO3 Nanofibers by
Electrospinning TechniqueCER-P-14 Supattra WongsaenmaiCER-P-14
Maejo University, Thailand CER-P-15 Influence of Sintering
Temperature on Electrical Properties of Lead-Free
Ba0.93Ca0.04La0.03Ti0.9Sn0.1O3 CeramicsCER-P-15 Nuttapaphat
AkkaramontrekunCER-P-15 Rajamangala University of Technology Isan,
Thailand CER-P-16 Synthesis and Characterization of (Cr,
Sb)-co-doped TiO2 Orange Pigment with High NIR
ReflectanceCER-P-16 Mantana SuwanCER-P-16 National Metal and
Materials Technology Center (MTEC), Thailand CER-P-17 Synthesis and
Textural Properties of High Surface Area Mesoporous MCM – 41
CER-P-17 Punchaluck SirinwaranonCER-P-17 Chulalongkorn University,
Thailand CER-P-18 Effects of SnO2-SiO2-MgO-Bi2O3-Y2O3 Additions on
Liquid Phase Sintering Silicon Nitride CER-P-18 Sasijuta
WattanarachCER-P-18 Chulalongkorn University, Thailand CER-P-19
Conversion of Coal Fly Ash to Zeolite X: Alkaline Fusion Followed
by Hydrothermal MethodCER-P-19 Panida WimuktiwanCER-P-19 National
Metal and Materials Technology Center (MTEC), Thailand CER-P-20
Synthesis and Characterization of SiO2 Nanoparticles Via Sol-gel
Process for Latent
Fingerprints Detection ApplicationsCER-P-20 Suttikan
ChaikulCER-P-20 National Metal and Materials Technology Center
(MTEC), Thailand CER-P-21 Effect of Alumina Addition on Rheological
Behavior of Shear Thickening FluidCER-P-21 Natnicha
NuampakdeeCER-P-21 Chulalongkorn University, Thailand CER-P-22
Influence of Pattern and Frequency of Mechanical Force on
Electrical Output Power of
Piezoelectric Circular Diaphragm CER-P-22 Muangjai
UnruanCER-P-22 Rajamangala University of Technology Isan,
Thailand
20
-
th
The 10th International Conference on Materials Science and
Technology
CER-P-23 Synthesis and Thermal Properties of C3AH6 Cement
Hydrate Derived from C12A7 CementCER-P-23 Chaiwat PhrompetCER-P-23
King Mongkut's Institute of Technology Ladkrabang, Thailand
CER-P-24 Photocatalytic Activities of SrxCa(1-x)TiO3 (x=0, 0.25,
0.5, 0.75 and 1) Powders Synthesized by
Solution Combustion Technique CER-P-24 Nicha SatoCER-P-24
Kasetsart University, Thailand CER-P-25 A Prototype of Rubber
Energy Harvesting Floor CER-P-25 Sujitra UnruanCER-P-25 Rajamangala
University of Technology Isan, Thailand CER-P-26 Characterization
and Properties of Lampang Kaolinite Clay for Standard Clay CER-P-26
Soravich MulintaCER-P-26 Lampang Rajabhat University, Thailand
CER-P-27 Effects of Firing Temperature of Red Clay and Sponge Waste
on Physical Properties for Plant
MaterialsCER-P-27 Sukanya PukpobsukCER-P-27 Lampang Rajabhat
University, Thailand CER-P-28 The Preparation of Bone China Body
from Pig Bone Ash, Lampang Kaolinite and Fly AshCER-P-28 Apinan
KhankhomCER-P-28 Lampang Rajabhat University, Thailand CER-P-29
Effect of Binder Content on the Slip Rheology and Green Properties
of Slip Cast AluminaCER-P-29 Kritkaew SomtonCER-P-29 National Metal
and Materials Technology Center (MTEC), Thailand CER-P-30 Use of
Waterglass from Rice Husk and Bagasse Ashes in the Preparation of
Fly Ash Based
GeopolymerCER-P-30 Khemmakorn GomonsirisukCER-P-30 National
Metal and Materials Technology Center (MTEC), Thailand CER-P-31 The
Study and Development of High Porous Geopolymer Concrete from
Industrial Wastes for
Energy Saving Building CER-P-31 Suteerapun PunlertCER-P-31
National Metal and Materials Technology Center (MTEC), Thailand
CER-P-32 Physical Properties and Thermal Conductivity of Soil -
Cement Block Geopolymer CER-P-32 Pongsak JittabutCER-P-32 Nakhon
Ratchasima Rajabhat University, Thailand
DESIGN AND MANUFACTURING + COMPUTATIONAL SCIENCE AND
ENGINEERINGINVITED LECTURES
DMC-I-01 Hybrid Metal Forming Processes for Mass Customized
ProductionDMC-I-01 Suwat JirathearanatDMC-I-01 Singapore Institute
of Manufacturing Technology, Singapore DMC-I-02 CFD Simulation and
Modeling of Metallurgical Processes DMC-I-02 Pruet
KowitwarangkulDMC-I-02 King Mongkut's University of Technology
North Bangkok, Thailand
ORAL PRESENTATIONSDMC-O-01 Determination of Wrinkling Initiation
for Aluminum Alloy Sheet based on Instability BehaviorDMC-O-01
Channarong YamchoangDMC-O-01 King Mongkut's University of
Technology North Bangkok, Thailand DMC-O-02 Analysis and Correction
of Defects for Deep Drawing Process of Stainless Sink by Use of
Finite Element Simulation DMC-O-02 Benjaphorn KhuanngernDMC-O-02
King Mongkut's University of Technology Thonburi, Thailand
21
-
th
The 10th International Conference on Materials Science and
Technology
DMC-O-03 Bending Limit Curves in Strain and Stress Space for
Advanced High Strength Steel SheetDMC-O-03 Phimmat KalawongDMC-O-03
King Mongkut's University of Technology North Bangkok, Thailand
DMC-O-04 Influence of Pre-Stretching Modes on the Forming Limit
Strain and Stress Diagrams of High
Strength Steel Sheet DMC-O-04 Korkiat LaokorDMC-O-04 King
Mongkut's University of Technology North Bangkok, Thailand DMC-O-05
Influence of Pre-Stretching on Fracture Forming Limit Curve of
Aluminum Alloys Sheet
AA5052-H32DMC-O-05 Taratip ChaimongkonDMC-O-05 King Mongkut's
University of Technology North Bangkok, Thailand DMC-O-06 Ductility
Improvement of the Co-28Cr-6Mo Alloy Processed by Selective Laser
Melting DMC-O-06 Pongnarin JiamwatthanachaiDMC-O-06 Prince of
Songkla University, Thailand DMC-O-07 Application of MATLAB GUI for
Modeling of Residual Stress and Distortion in
Arc Welded Metal DMC-O-07 Kittichai SojiphanDMC-O-07 King
Mongkut's University of Technology North Bangkok, Thailand DMC-O-08
Fatigue Assessment of an Offshore Piping System by Finite Element
Analysis DMC-O-08 Somboon OtarawannaDMC-O-08 National Metal and
Materials Technology Center (MTEC), Thailand DMC-O-09 Investigation
of the Structural Integrity of a Cryogenic Tank with Sunken Marks
by Finite
Element Analysis DMC-O-09 Somboon OtarawannaDMC-O-09 National
Metal and Materials Technology Center (MTEC), Thailand DMC-O-10
Study Underflow diameter, Free Vortex, Cylindrical and Conical
Length of Hydrocyclone to
Achieve High Separation Sharpness DMC-O-10 Pakpoom
SupachartDMC-O-10 King Mongkut's University of Technology Thonburi,
Thailand DMC-O-11 The Quality Improvement of Molten Aluminium Alloy
in Melting and Casting ProcessDMC-O-11 Jintana
TempiamwatcharothaiDMC-O-11 King Mongkut's University of Technology
North Bangkok, Thailand DMC-O-12 Determination of Internal and
External Surface Areas of Atomistic Porous Carbons DMC-O-12
Poomiwat PhadungbutDMC-O-12 Mahidol University, Thailand
POSTER PRESENTATIONSDMC-P-01 Numerical-Experimental Model and
Polynomial Regression Method for Interpretation of
G-BHN Relation of Kraft-based Fibrous Composites Evaluated by
using Brinell AnalysisDMC-P-01 Rakdiaw MuangmaDMC-P-01 Chiang Rai
Rajabhat University, Thailand
MATERIALS FOR ENERGYINVITED LECTURES
ENR-I-01 Lithium-ion Battery: Material and System Design towards
High Rate CapabilityENR-I-01 Pimpa LimthongkulENR-I-01 National
Metal and Materials Technology Center (MTEC), Thailand
ORAL PRESENTATIONSENR-O-01 Decreasing Precipitation in Biodiesel
blending with Fossil Diesel by using Partial
Hydrogenation ENR-O-01 Ukrit SahapatsombutENR-O-01 National
Metal and Materials Technology Center (MTEC), Thailand
22
-
th
The 10th International Conference on Materials Science and
Technology
ENR-O-02 Effect of SiO2 Pore Size on Sulfur Tolerance of
Metallic Catalysts used for Partial Hydrogenation of Biodiesel
ENR-O-02 Theerapron Leung OnENR-O-02 National Metal and
Materials Technology Center (MTEC), Thailand ENR-O-03 The Influence
of Precursors on Optical Properties of Carbon Nanodots Synthesized
via
Hydrothermal Carbonization TechniqueENR-O-03 Kamonwan
Aup-NgoenENR-O-03 King Mongkut's University of Technology Thonburi,
Thailand ENR-O-04 Effects of Cr Doping into Mn-site on Physical and
Electrochemical Properties of Li2MnSiO4
Cathode Materials for Li-ion Batteries ENR-O-04 Thanya
PhraewphiphatENR-O-04 National Metal and Materials Technology
Center (MTEC), Thailand ENR-O-05 Synthesis and Characterizations of
a Family of Dual-functional Lithium Salts for Lithium-
Polymer BatteriesENR-O-05 Priew EiamlamaiENR-O-05 National Metal
and Materials Technology Center (MTEC), Thailand ENR-O-06
Electrophoretic Deposition of Carbon Nanotubes onto Metal
Substrates: Characterization and
Electrochemical ApplicationsENR-O-06 Napapon
Massa-AngkulENR-O-06 Khon Kaen University, Thailand ENR-O-07 Carbon
for Anode Materials from Rice Husk and Rice StrawENR-O-07 Pranuda
JivaganontENR-O-07 National Metal and Materials Technology Center
(MTEC), Thailand ENR-O-08
3,12-Bis(phenylmethylamine)-[i]-(1-phenyl-pyrrolidine-2,5-diono)-[5]helicene:
A New
Semiconductor Material for Organic Electronic Applications
ENR-O-08 Laongdao KangkaewENR-O-08 National Metal and Materials
Technology Center (MTEC), Thailand ENR-O-09 A Novel Red Dye from
[5]Helicene Derivative for Organic Light-Emitting Diode ENR-O-09
Waraporn PanchanENR-O-09 National Metal and Materials Technology
Center (MTEC), Thailand ENR-O-10 Solution Processable Molybdenum
Oxide as a Hole Transport Layer for Organic Photovoltaic
DevicesENR-O-10 Chaiyuth SaekungENR-O-10 National Metal and
Materials Technology Center (MTEC), Thailand
POSTER PRESENTATIONSENR-P-04 Synthesis and Characterizations of
Y-doped BaCeO3 Ceramic for Use as Solid Electrolyte in
Solid Oxide Fuel CellENR-P-04 Wiset SomkhuanENR-P-04 Chiang Mai
University, Thailand ENR-P-05 Physical and Electrical Property of
TiO2 Nanotube Arrays for Supercapacitors ENR-P-05 Somwan
ChumphongphanENR-P-05 Mae Fah Luang University, Thailand ENR-P-07
Phase Transformation in Sputtered-vanadium Oxide Films under
Post-annealing Heat TreatmentENR-P-07 S.Tipawan KhlayboonmeENR-P-07
King Mongkut's Institute of Technology Ladkrabang, Thailand
ENR-P-08 Electrochemical Behavior of the Zinc Anode in Various
Conditional EnvironmentsENR-P-08 Sawitta TriamthaisongENR-P-08 Khon
Kaen University, Thailand ENR-P-09 The Interconnected Open-channel
Highly Porous Carbon Material Derived from Pineapple Leaf
Fibers as a Sustainable Electrode Material for Electrochemical
Energy Storage DevicesENR-P-09 Supacharee RoddechaENR-P-09
Kasetsart University, Thailand
23
-
th
The 10th International Conference on Materials Science and
Technology
ENR-P-11 Improvement of the Electrical Properties in
Ba(Ti0.92Sn0.08)O3 Lead-Free Ceramics by Ca Addition and Sintering
Profile
ENR-P-11 Pornsuda BomlaiENR-P-11 Prince of Songkla University,
Thailand ENR-P-12 Activated Carbon for EDLC Electrodes from Palm
Empty Fruit BunchENR-P-12 Yatika SomrangENR-P-12 National Metal and
Materials Technology Center (MTEC), Thailand ENR-P-13 Influence of
Gd on Water-Gas Shift Performance of Ni/CeO2 Catalyst ENR-P-13
Pannipa TepamatrENR-P-13 Thammasat University, Thailand
MATERIALS TECHNOLOGY FOR ENVIRONMENTINVITED LECTURES
ENV-I-01 Metal Nanoparticle/polymer/carbon Nanotube Hybrid
Materials for Highly Sensitive and Selective Volatile Organic
Compound Detection
ENV-I-01 Worawut MuangratENV-I-01 Shinshu University, Japan
ENV-I-02 Chiang Rai Zero Waste : A Step-by-step Approach toward
Partnership for Sustainability ENV-I-02 Panate
ManomaiviboolENV-I-02 Mae Fah Luang University, Thailand
ORAL PRESENTATIONSENV-O-01 Influence of Silica Supports on
Photocatalytic Oxidation of Sulfur Compound and Sulfone
AdsorptionENV-O-01 Nitipon ChekuntodENV-O-01 King Mongkut's
University of Technology North Bangkok, Thailand ENV-O-03 Enhancing
the Photocatalytic Degradation of TiO2 Over Pineapple Fibers
Material for
Methyleneblue RemovalENV-O-03 Suchadee SribenjaENV-O-03
Mahasarakham University, Thailand ENV-O-04 Bamboo Char-supported
Platinum Nanoparticle Electrocatalyst for the Oxygen Reduction
ReactionENV-O-04 Samerkhae JongthammanurakENV-O-04 National
Metal and Materials Technology Center (MTEC), Thailand ENV-O-05
Effect of Surfactant on Collapse in Oil Palm Wood during Drying
ENV-O-05 Choosak RittiphetENV-O-05 Walailak University, Thailand
ENV-O-06 Optical Transparent and Hydrophobic Properties of
TEOS/OTES Hybrid Materials by Sol-Gel
ProcessingENV-O-06 Usanee PantulapENV-O-06 Department of Science
Service, Thailand ENV-O-07 Glass Batch Modification to Improve The
Weathering Resistance in Soda-lime Silicate GlassENV-O-07 Ekarat
MeechoowasENV-O-07 Department of Science Service, Thailand ENV-O-08
Mechanical Properties and Thermal Performance of Autoclaved Aerated
Lightweight Concrete
Wall Consisting of Phase Change MaterialENV-O-08 Aitthi
KhongthonENV-O-08 Naresuan University, Thailand ENV-O-09
Incorporating Black Dust into Autoclaved Aerated Concrete Wall for
Heat Transfer ReductionENV-O-09 Ketwadee JanyoosukENV-O-09 Naresuan
University, Thailand
24
-
th
The 10th International Conference on Materials Science and
Technology
ENV-O-10 Influence of Type and Composition of SCM on Expansion
of Mortar Bars from Alkali -Silica Reaction
ENV-O-10 Suvimol SujjavanichENV-O-10 Kasetsart University,
Thailand ENV-O-11 Impact of Engine Oil's Additives on Particulate
Matter's Micro- and Nanostructure using
Electron Microscopy Image Analysis ENV-O-11 Phyo Zin Ko
KoENV-O-11 King Mongkut's Institute of Technology Ladkrabang,
Thailand
POSTER PRESENTATIONSENV-P-01 The Effects of Biochar additive on
the Properties of Geopolymer Materials ENV-P-01 Phitchayanin
KhamlueENV-P-01 Chiang Mai University, Thailand ENV-P-02
Preparation and Characterization of Ceramic Waste-Based Geopolymer
Ceramic Composites
for Substrate Culture ApplicationENV-P-02 Kannikar
KaewapaiENV-P-02 Chiang Mai University, Thailand ENV-P-03 Surface
Morphologies and Durability on Water Contact Angle of Titanium
Dioxide
Nanoparticle Thin Films ENV-P-03 Buppachat ToboonsungENV-P-03
Nakhon Ratchasima Rajabhat University, Thailand ENV-P-04 Ammonia
Adsorption using Activated Carbon Derived from Nipa Palm Husk Via
Chemical
ActivationENV-P-04 Chaichana PiyamawadeeENV-P-04 Chulalongkorn
University, Thailand ENV-P-05 Room Temperature Gas Sensor Based on
Helical Carbon CoilsENV-P-05 Udomdej PakdeeENV-P-05 Rajamangala
University of Technology Krungthep, Thailand ENV-P-06 Synthesis of
Modified Chitosan with Thiamine Hydrochloride as the Adsorbent for
Calcium
(II) Ion RemovalENV-P-06 Ratana SananmuangENV-P-06 Naresuan
University, Thailand ENV-P-07 Removal of Chromium(VI) ion in
Solution by Chitosan-Polyaniline Composited Membrane and
Coating on Plaster Rod as Adsorbed Electrode ENV-P-07 Ratana
SananmuangENV-P-07 Naresuan University, Thailand ENV-P-08 Effect of
Sintering Temperature on Mechanical and Electrical Properties of
Lead-free
Bi0.5(Na0.4K0.1)Ti0.98Zr0.02O3 Piezoelectric Ceramics ENV-P-08
Pichitchai ButnoiENV-P-08 Chiang Mai University, Thailand ENV-P-09
Utilization of Aluminum Buffing Dust as a Raw Material for the
Production of Mullite ENV-P-09 Nuntaporn KongkajunENV-P-09
Thammasat University, Thailand ENV-P-10 Physical and Thermal
Properties of Cement Board made from Waste Paper and
Rice Straw ENV-P-10 Watcharapong WongkeoENV-P-10 Nakhon
Ratchasima Rajabhat University, Thailand ENV-P-11
Photoelectrocatalytic and Ultrasonic-assisted for Organic Dye
Degradation using Zinc Oxide
(ZnO) ElectrodeENV-P-11 Chirarat LunkhamENV-P-11 Rajamangala
University of Technology Thanyaburi, Thailand
25
-
th
The 10th International Conference on Materials Science and
Technology
ENV-P-12 Preparation and Characterization of Polyurethane Sponge
Decorated with Reduced Graphene Oxide for Oil Removal
ENV-P-12 Natcha JirasuttisarnENV-P-12 King Mongkut's Institute
of Technology Ladkrabang, Thailand ENV-P-13 Strength Improvement of
High-Yield Pulp Fibers from Jute Using Alkaline-Oxygen
TreatmentENV-P-13 Jatuporn KongcrupENV-P-13 Kasetsart University,
Thailand ENV-P-14 Chemical Composition and Morphological Properties
of Oil Palm Fronds and Its Application in
the Production of NSSC Pulp for Reinforcing Corrugating Medium
Paper ENV-P-14 Wiroj SavangsrisutikunENV-P-14 Kasetsart University,
Thailand ENV-P-15 Effect of Basalt Addition and Curing Condition on
the Strength Development of
Geopolymer ENV-P-15 Pimpun HenpraserttaeENV-P-15 National Metal
and Materials Technology Center (MTEC), Thailand ENV-P-16 Effects
of the Chemical Treatment on Coal Bottom Ash for the Utilization in
Fiber- Reinforced
Cement Composites ENV-P-16 Passakorn SonprasarnENV-P-16
Kasetsart University, Thailand ENV-P-17 The Influences of Chemical
Treatment on Recycled Rejected Fiber Cement Used as Fillers in
the Fiber Cement Products ENV-P-17 Peerapat PahusuwannoENV-P-17
Kasetsart University, Thailand ENV-P-18 Hydrophobic and Oleophilic
Filter Paper for Oil/Water SeparationENV-P-18 Sunisa
JindasuwanENV-P-18 King Mongkut's University of Technology North
Bangkok, Thailand
METALS, ALLOYS AND INTERMETALLIC COMPOUNDSINVITED LECTURES
MET-I-01 Future Manufacturing Now – SLM Solutions at a glance:
SLM technology, Applications, Additive Intelligence and R&D
MET-I-01 Edwin MokMET-I-01 SLM Solutions Singapore Pte Ltd,
Singapore MET-I-02 A Microstructure Based Design for Applications
of Advanced High Strength Steels MET-I-02 Vitoon
UthaisangsukMET-I-02 King Mongkut's University of Technology
Thonburi, Thailand MET-I-03 Microstructure Formation of Solder
Alloys During Soldering Using Synchrotron Radiography
ImagingMET-I-03 Mohd Arif Anuar Mohd SallehMET-I-03 Universiti
Malaysia Perlis (UniMAP), Malaysia
ORAL PRESENTATIONSMET-O-01 Surface Smoothing by Friction Stir
Forming for A5083 Aluminum Alloy Plate MET-O-01 Takahiro
OhashiMET-O-01 Kokushikan University, Japan MET-O-02
Spheroidization of Fe-intermetallic Compounds in Al-Si Alloys by
Ultrasonic VibrationMET-O-02 Chakkrist PhongphisutthinanMET-O-02
National Metal and Materials Technology Center (MTEC), Thailand
MET-O-03 Isothermal Aging of Al-Ni-Sc Alloy Containing Al3Ni
Microfibers and Al3Sc NanoprecipitatesMET-O-03 Chanun
SuwanpreechaMET-O-03 King Mongkut's University of Technology
Thonburi, Thailand
26
-
th
The 10th International Conference on Materials Science and
Technology
MET-O-04 Synthesis of Al-Li Alloys by Hybrid Semi-Solid and
Sonication ProcessingMET-O-04 Payodhar PadhiMET-O-04 Konark
Institute of Science and Technology, India MET-O-05 Influence of
Magnesium on Microstructures and Mechanical Properties of
Cu-38Zn-1Sn-0.2Al-
0.2Si AlloysMET-O-05 Pemika SuksongkarmMET-O-05 King Mongkut's
University of Technology Thonburi, Thailand MET-O-06 Corrosion
Behaviors of Ship Structural Steel in Simulated Marine Tidal
Environment MET-O-06 Nattapol JaiyosMET-O-06 The Sirindhorn
International Thai-German Graduate School of Engineering (TGGS),
King Mongkut's
University of Technology North Bangkok, Thailand MET-O-07
Metallurgical Evaluation of 304H Coil for Cracking FurnaceMET-O-07
Siriwan OuampanMET-O-07 National Metal and Materials Technology
Center (MTEC), Thailand MET-O-08 Effect of Substrate-Target
Distance on the Structure of TiCrN Films Deposited from Mosaic
Target by Reactive DC Magnetron Sputtering MET-O-08 Nirun
Witit-AnunMET-O-08 Burapha University, Thailand MET-O-09 One Step
Pressing-Annealing to Produce LTP MnBi MagnetsMET-O-09 Thanida
CharoensukMET-O-09 Walailak University, Thailand MET-O-10 Effects
of Admixed Ni, B and C Elements on Microstructure and Property of
Sintered SteelsMET-O-10 Bhanu VetayanugulMET-O-10 National Metal
and Materials Technology Center (MTEC), Thailand MET-O-11
Microstructure, Mechanical and Wear Properties of Sintered
Fe-Mo-Si-C AlloysMET-O-11 Kittikhun RuangchaiMET-O-11 Naresuan
University, Thailand MET-O-12 Mechanical and Wear Properties of
Pearlitic Ductile Iron-like Sintered Fe-Cr-Mo-Si-C AlloysMET-O-12
Kittikhun RuangchaiMET-O-12 Naresuan University, Thailand MET-O-13
Influences of Cooling Rate and Carbon Content on Microstructures,
Mechanical and Wear
Properties of Sintered Fe-Mo-C Steels MET-O-13 Monnapas
MorakotjindaMET-O-13 National Metal and Materials Technology Center
(MTEC), Thailand MET-O-14 Effect of Boron Addition and Sintering
Atmosphere on Precipitation in Sintered
Fe-Mo-C Steels MET-O-14 Nattaya TosangthumMET-O-14 National
Metal and Materials Technology Center (MTEC), Thailand MET-O-15
Thermoelectric Properties of Lead Telluride Processed by Mechanical
Grinding and Hot-
Pressing TechniqueMET-O-15 Mongkol BumrungponMET-O-15 Tokushima
University, Thailand MET-O-16 Microstructure and Property of
Sintered Fe-4Ni-0.5Mo-0.14Mn-0.22B-xC SteelsMET-O-16 Thanyaporn
YotkaewMET-O-16 National Metal and Materials Technology Center
(MTEC), Thailand MET-O-17 Effect of Waste-Derived Calcium Sulfate
Additions on the Tribological Properties of Sintered
Steel-Based MaterialMET-O-17 Chiraporn AuechalitanukulMET-O-17
King Mongkut's University of Technology Thonburi, Thailand MET-O-18
Tribological Properties of Sintered Graphite-Steel Composites
Containing Lignite Bottom AshMET-O-18 Chiraporn
AuechalitanukulMET-O-18 King Mongkut's University of Technology
Thonburi, Thailand
27
-
th
The 10th International Conference on Materials Science and
Technology
POSTER PRESENTATIONSMET-P-01 The Corrosion Resistance of
CoCrFeNi High Entropy Alloys in Chloride SolutionMET-P-01 Piyanut
MuangtongMET-P-01 University of Sheffield, United Kingdom MET-P-02
Porous Copper Fabrication Using Powder Metallurgy Routes MET-P-02
Shaiful Anwar IsmailMET-P-02 University of Sheffield, United
Kingdom MET-P-03 Structure and Morphology Study of Very Thin TiCrN
Films Deposited by Unbalanced
Magnetron Co-sputteringMET-P-03 Chutima PaksunchaiMET-P-03
Rajamangala University of Technology Krungthep, Thailand MET-P-05
Effect of Heat Input in Welding on the Size and Quantities of
Titanium Carbonitride Ti(C,N)
for Heat Affected Zone in Stainless Steel Grade AISI 321
MET-P-05 Titinan MethongMET-P-05 King Mongkut's University of
Technology Thonburi, Thailand MET-P-06 Effects of Heat Treatment
and Composition on Ball-Milled MnBi and MnBi/Co Magnets MET-P-06
Thanida CharoensukMET-P-06 Walailak University, Thailand MET-P-07
Effect of Ethanol on Hydrophilicity of the Anodized Films Performed
by Two-Step Anodization
at Low Current Density MET-P-07 Phanawan WhangdeeMET-P-07
Rajamangala University of Technology Isan, Thailand MET-P-08
Structure and Oxidation Behavior CrN Thin Films Deposited Using DC
Reactive Magnetron
Sputtering MET-P-08 Adisorn BuranawongMET-P-08 Burapha
University, Thailand MET-P-09 Effect of Microstructure on the Low
Temperature Toughness of Low Carbon Steel for Spent
Nuclear Fuel Storage Cask MET-P-09 Jehyuk OhMET-P-09 Korea
Institute of Industrial Technology(KITECH), South Korea MET-P-10
Comparision of Wear Behavior of Commercial Aluminium and Aluminium
- Alumina Metal
Matrix Nano Composites in Dry ConditionMET-P-10 Payodhar
PadhiMET-P-10 Konark Institute of Science and Technology, India
MET-P-11 Impact of Oil Additive Characteristics on Biofuel Engine
Wear using Electron Microscopy and
Laser Diffraction Spectroscopy MET-P-11 Panyakorn
RungsritanapaisanMET-P-11 King Mongkut's Institute of Technology
Ladkrabang, Thailand MET-P-12 Microstructure, Mechanical and Wear
Properties of Sintered Molybdenum-Containing Steels
Modified by Nickel Addition MET-P-12 Pongsak WilaMET-P-12
National Metal and Materials Technology Center (MTEC), Thailand
MET-P-13 Design of Experiment for Studying Grain Size of Alpha
Aluminum by varying Pouring
Temperature and Plate LengthMET-P-13 Suteerapun PunlertMET-P-13
National Metal and Materials Technology Center (MTEC), Thailand
MET-P-15 Equal Channel Angular Pressing of a Sprayed Formed
Al-Cu-Li Alloy MET-P-15 Chaiyasit BanjongprasertMET-P-15 Chiang Mai
University, Thailand MET-P-16 Optimization of Hardness of TiAlN
Coating using the Taguchi MethodMET-P-16 Kirati WareeMET-P-16
National Metal and Materials Technology Center (MTEC), Thailand
28
-
th
The 10th International Conference on Materials Science and
Technology
POLYMERSINVITED LECTURES
POL-I-01 Functional Materials Based on Biodegradable Polylactide
Copolymers: Form Synthesis to Fabrication and Applications
POL-I-01 Pakorn OpaprakasitPOL-I-01 Sirindhorn International
Institute of Technology, Thailand POL-I-02 Superior Tough Polymers:
Recent Advances in Polymer Processing POL-I-02 Hiroshi ItoPOL-I-02
Yamagata University, Japan POL-I-03 Natural Rubber (NR) in Rail and
Agriculture Applications: Rubber Rail Crossing Panels and
Reinforced Porous PipesPOL-I-03 Ittipol JangchudPOL-I-03 King
Mongkut's Institute of Technology Ladkrabang, Thailand
ORAL PRESENTATIONSPOL-O-01 Injection Moldable Poly(lactic acid)
(PLA)-Polybutylene Succinate (PBS)-Activated Carbon
Composite Foams: Effects of PLA:PBS RatiosPOL-O-01 Kittipong
HrimchumPOL-O-01 National Metal and Materials Technology Center
(MTEC), Thailand POL-O-02 Electro-Spinning and Carbonisation of
Lignin FibresPOL-O-02 Bongkot HararakPOL-O-02 University of
Birmingham, United Kingdom POL-O-03 Stretchable and Ultrasensitive
Strain and/or Self-sensing Material Based on Carbon
Nanostructures-polymer NanocompositesPOL-O-03 Tejendra Kumar
GuptaPOL-O-03 Amity University, India POL-O-04 Formation of Porous
Polymer Nanostructures by Imprinting Process: Phase Separation
and
Foaming of PS/PVA Blend at the Nanoscale POL-O-04 Paritat
MuanchanPOL-O-04 Yamagata University, Japan POL-O-05 Oxygen
Permeability Enhancement of Commercial Polyethylene
terephthalate/Polyethylene
Laminated Film by Laser Micro-Perforation Technique; Modified
Atmosphere Packaging for Ready to Eat Fresh-Cut
POL-O-05 Ajcharaporn AonteePOL-O-05 National Metal and Materials
Technology Center (MTEC), Thailand POL-O-06 A Comparison of
Microhole Formation Behavior on Polypropylene and Poly(lactic acid)
Film
Using CO2 Laser Irradiation POL-O-06 Charinee WinotapunPOL-O-06
National Metal and Materials Technology Center (MTEC), Thailand
POL-O-07 Enhancement of Cellular Structure and Properties of Flame
Retardant Insulation
Polyethylene Octene Elastomer (POE) Foam by Blending with
Natural RubberPOL-O-07 Karnjana SawangpetPOL-O-07 Prince of Songkla
University, Thailand POL-O-08 The Stress-strain Extraction of
Rubber-foam Material by using Artificial Neural Network and
Genetic AlgorithmPOL-O-08 Ekachai OuysookPOL-O-08 Mahidol
University, Thailand POL-O-09 Strain-induced Crystallization of
Natural Rubber/Halloysite Nanotubes Composites in the
Presence of Alkanolamide-based Palm Stearin POL-O-09 Nureeyah
JehsohPOL-O-09 Prince of Songkla University, Thailand
29
-
th
The 10th International Conference on Materials Science and
Technology
POL-O-10 Novel Thermoplastic Vulcanizates based on Polyamide-12
Blends: Influence of modified Devulcanized Natural Rubber Gloves on
Properties of the Blends
POL-O-10 Boripat SripornsawatPOL-O-10 Prince of Songkla
University, Thailand POL-O-11 Influence of Filler Network Formation
on De-vulcanization Efficiency of Carbon Black Filled
SBR and NRPOL-O-11 Anuwat WorleePOL-O-11 Prince of Songkla
University, Thailand
POSTER PRESENTATIONSPOL-P-01 Activated Carbon Loaded
Lignocellulosic Fibers by Pulp Refining Process for Dye and
Metal
Ion Absorbing Paper POL-P-01 Suteera WitayakranPOL-P-01
Kasetsart University, Thailand POL-P-03 Use of Steam Explosion as a
Green Alternative Method to Prepare Pulp from
Pineapple LeavesPOL-P-03 Supachok TanpichaiPOL-P-03 King
Mongkut's University of Technology Thonburi, Thailand POL-P-05
Cellulose/Activated Carbon Biocomposite Film from Sisal Fiber for
Dye RemovalPOL-P-05 Noppon SomsestaPOL-P-05 Chulalongkorn
University, Thailand POL-P-06 Isolation of Sugarcane Bagasse
Nanofibrils from Agricultural Waste Using an
Environmentally Friendly Mechanical TreatmentPOL-P-06 Intatch
HongrattanavichitPOL-P-06 Chulalongkorn University, Thailand
POL-P-07 Poly(Butylene Succinate) and Recycled Poly(Ethylene
Terephthalate) Blends adding GMA
as Compatibilizer: Mechanical Properties and Chemical Resistance
to Household Chemicals
POL-P-07 Nattakarn HongsriphanPOL-P-07 Silpakorn University -
Sanamchandra Palace Campus, Thailand POL-P-08 Preparation and
Properties of Composite Films From Poly(Butylene Succinate),
Poly(Butylene
Adipate-Co-Terephthalate) and ZeolitePOL-P-08 Nattakarn
HongsriphanPOL-P-08 Silpakorn University - Sanamchandra Palace
Campus, Thailand POL-P-09 Preparation and Characterization of
Siloxane Modified Polyacrylate POL-P-09 Weepol PramualkijjaPOL-P-09
Chulalongkorn University, Thailand POL-P-10 Facile Preparation of
Cellulose II Nanofibers Using NaOH/Urea-assisted
PretreatmentPOL-P-10 Kraiwit PakutsahPOL-P-10 Chulalongkorn
University, Thailand POL-P-11 Influence of Pulverized Citrus Fibers
on Disintegration of Citrus Fiber/Tapioca Pregel Starch
Composite TabletsPOL-P-11 Chaiyaporn PomchaitawardPOL-P-11
National Metal and Materials Technology Center (MTEC), Thailand
POL-P-12 A Case Study of Recycled Poly(Lactic Acid) Contaminated
With Petroleum-based
Thermoplastics Used In Packaging Application POL-P-12 Pajaera
PatanathabutrPOL-P-12 Silpakorn University - Sanamchandra Palace
Campus, Thailand POL-P-13 Effect of β-Cyclodextrin on Antifungal,
Release Control of Sweet Basil Oil and Mechanical
Properties of LDPE Film Incorporated with Essential OilPOL-P-13
Poonsub ThreepopnatkulPOL-P-13 Silpakorn University, Thailand
30
-
th
The 10th International Conference on Materials Science and
Technology
POL-P-14 Effect of Calcium Ion Concentration on Rheological
Properties and Large Amplitude Oscillatory Shear Behavior of Mixed
Gels of Low Acyl Gellan Gum and Konjac Glucomanan/Xanthan Gum
POL-P-14 Thidarat MakmoonPOL-P-14 National Metal and Materials
Technology Center (MTEC), Thailand POL-P-15 Effect of Different
Organoclay from Different Master Batch on Crystallization of
PLA/EVA BlendsPOL-P-15 Chanchai ThongpinPOL-P-15 Silpakorn
University - Sanamchandra Palace Campus, Thailand POL-P-16
Preparation and Property Testing of Flame Retardant Soundproofing
Sheets from Used
Peritoneal Dialysis Solution ContainersPOL-P-16 Boonnak
SukhummekPOL-P-16 King Mongkut's University of Technology Thonburi,
Thailand POL-P-17 Structural Modification of Styrene Maleic
Anhydride Copolymers for Plant Bioactive
Compound Extraction POL-P-17 Patchara PunyamoonwongsaPOL-P-17
Mae Fah Luang University, Thailand POL-P-18 Reclaimed Rubber as a
Cost Reduction Filler in Natural Rubber/Polypropylene Blend:
Effect of Reclaimed Rubber Contents POL-P-18 Anoma
ThitithammawongPOL-P-18 Prince of Songkla University, Thailand
POL-P-19 Preparation and Characterization of Gelatin/Maleic
Anhydride Grafted Ethylene Vinyl Acetate
Copolymer Film POL-P-19 Sudsiri HemsriPOL-P-19 Silpakorn
University - Sanamchandra Palace Campus, Thailand POL-P-20 The
Effect of Poly(butylene adipate-co-terephthalate) on
Crystallization Behavior and
Morphology of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate)
POL-P-20 Sitthi DuangphetPOL-P-20 Mae Fah Luang University,
Thailand POL-P-21 Effect of light-aging on Intelligent pH Indicator
Film Composed of Gelatin and Extracted
Anthocyanin from Butterfly PeaPOL-P-21 Pornnapa
KasemsiriPOL-P-21 Khon Kaen University, Thailand POL-P-22
Hydroxylated Natural Rubber Effect on Crystallinity and Mechanical
Properties of PLAPOL-P-22 Nutthapong TriampanichkulPOL-P-22 King
Mongkut's University of Technology Thonburi, Thailand POL-P-23
Dynamic Vulcanization of NR/PCL Blends: Effect of Rotor Speed on
Morphology, Tensile
Properties and Tension SetPOL-P-23 Theeraphat TanprasertPOL-P-23
Silpakorn University, Thailand POL-P-24 Effect of Alternative
Fillers on the Properties of Rubber CompoundsPOL-P-24 Wasana
KhongwongPOL-P-24 Thailand Institute of Scientific and
Technological Research, Thailand POL-P-26 Effect of Poly(vinyl
alcohol) on Thermoelectric Properties of Sodium Cobalt
OxidePOL-P-26 Chutima OopathumpPOL-P-26 Rajamangala University of
Technology Krungthep, Thailand
TESTING AND RELIABILITYINVITED LECTURES
TES-I-01 Understanding Nanostructures and Nanostructure
Development using X-ray and Complementary Spectroscopic
Techniques
TES-I-01 Yeng Ming LamTES-I-01 Nanyang Technological University,
Thailand
31
-
th
The 10th International Conference on Materials Science and
Technology
TES-I-02 XPS and XAS for Characterization of Carbon Materials
TES-I-02 Prayoon SongsiriritthigulTES-I-02 Suranaree University of
Technology, Thailand TES-I-03 Applications of Synchrotron-based
X-ray Absorption Spectroscopy and Infrared Microscopy
to Investigate on Advanced Functional Materials TES-I-03 Pinit
KidkhunthodTES-I-03 Synchrotron Light Research Institute,
Thailand
ORAL PRESENTATIONSTES-O-01 Application of Ultrasonic Inspection
for Microstructure Analysis of Metals TES-O-01 Kittichai
SojiphanTES-O-01 King Mongkut's University of Technology North
Bangkok, Thailand TES-O-02 A Barkhausen Noise Measuring System for
Steel Hardness EvaluationTES-O-02 Nopparat SeemuangTES-O-02 King
Mongkut's University of Technology North Bangkok, Thailand TES-O-04
A Study of Size and Surface Measurement of Nanoparticles and
Mesoporous Materials and
Interlaboratory Comparison TES-O-04 Bralee ChayasombatTES-O-04
National Metal and Materials Technology Center (MTEC), Thailand
TES-O-05 Failure Analysis of Superheat Tube 2.5Cr-1Mo in Biomass
Power Plant TES-O-05 Boonhlua KhwansriTES-O-05 King Mongkut's
University of Technology Thonburi, Thailand TES-O-06 X-Ray and
Computed Tomography as a Tool for Quality Assurance, Process
Optimization and
Material Characterization in the Field of Additive
ManufacturingTES-O-06 Philip SperlingTES-O-06 YXLON International
GmbH, Germany
POSTER PRESENTATIONSTES-P-01 The Effects of Ion Implantation on
Crystal Structure, Optical and Mechanical Properties of
Natural Spinel TES-P-01 Chanapa PantongTES-P-01 Thammasat
University, Thailand TES-P-02 Measurement of Potassium Ferricyanide
Concentration in Electrolyte Solution using Cyclic
Voltammetry by Frequency Domain ApproachTES-P-02 Bhanupol
KlongratogTES-P-02 King Mongkut's Institute of Technology
Ladkrabang, Thailand
SPECIAL SESSION: INNOVATIVE TEXTILES FOR FUTURE HEALTHCARE
APPLICATIONTEX-I-01 Multifunctionality in Textiles using
Metal-organics Framework TEX-I-01 Juan HinestrozaTEX-I-01 Cornell
University, United State of America TEX-I-02 Smart Textiles Having
Sensors and Actuators to Help Human ActivityTEX-I-02 Mutsumi
KimuraTEX-I-02 Shinshu University, Japan
32
-
Plenary Lectures
th
33
-
th
The 10th International Conference on Materials Science and
Technology
PL-01
3D Printing Materials Sciences
Y. Morris Wang Physical and Life Sciences Directorate, Lawrence
Livermore National Laboratory,
Livermore, CA 94550, USA Abstract The progress of materials
science and technology is often propelled by the development and
breakthrough of synthetic techniques. The recently emerged 3D
printing technologies (or additive manufacturing (AM)) utilize
computer-aided design files to produce materials and parts that
have potential applications in multiple fields. Compared to
conventional manufacturing techniques, AM has advantages of time-
and cost-saving, minimum waste, and large design freedom for
complex geometry components. Although AM focuses more frequently on
an engineering scheme, it offers unique opportunities to tailor
materials properties with highly nonequilibrium microstructures
and/or through ingenious structural designs, leading to
extraordinary materials properties that can extend far beyond those
achievable via conventional processing methods. This helps to open
a new field of 3D printing materials science. In this presentation
we will show a few interesting examples of common engineering
materials that can be manufactured by 3D printing technologies,
including metals and alloys, ceramics, carbon, and lattice
structures derived from these baseline materials. While we are
excited about the unique properties that can be achieved in these
materials, some serious deficiencies exist in 3D printing
technologies. We will discuss immediate scientific challenges and
potential solutions. This work was performed under the auspices of
the U.S. Department of Energy by Lawrence Livermore National
Laboratory under Contract DE-AC52-07NA27344. The speaker would like
to thank a large number of colleagues, postdoctoral staff members,
and graduate students who have contributed to this work.
34
-
th
The 10th International Conference on Materials Science and
Technology
PL-02
State-of-The-Art Titanium Alloys by Powder Metallurgy
Process
Katsuyoshi Kondoh Joining and Welding Research Institute, Osaka
University
The conventional titanium (Ti) alloys are strengthened by using
expensive and poisonous elements such as vanadium, niobium and
molybdenum. In our previous studies, the cheap elements such as
oxygen, nitrogen, carbon, silicon and hydrogen are selected to
significantly improve the mechanical properties of α-Ti sintered
materials by solid-solution strengthening and/or grains refinement
effects. In case of iron (Fe) addition, which is one of β phase
stabilizing elements, network-structured βphases containing Fe
atoms were formed at α-Ti grain boundaries when the elemental
mixture powder of pure Ti powder and pure Fe particles was
consolidated. With increase in additional Fe contents, the volume
fraction of βphase and mechanical strength proportionally
increased. For example, PM Ti-6wt.%Fe alloy indicated UTS of 1246
MPa and elongation of 22.4 % at ambient temperature. These
properties are much superior compared to the commercial Ti-6Al-4V
(Ti64) alloys. Regarding the electrochemical corrosion behavior of
Ti-Fe alloys, the corrosion current slightly decreased compared to
pure Ti, however, it was not a significant difference in the
industrial application. In this talk, the presentative results and
performances of the novel Ti materials via powder metallurgy route
will be introduced.
35
-
th
The 10th International Conference on Materials Science and
Technology
PL-03
Ceramics Manufacturing by Spark Plasma Sintering
Takashi Gotoa,b* aNew Industry Creation Hatchery Center, Tohoku
University, Sendai 980-8579, Japan
bState Key Laboratory of Advanced Technology for Materials
Synthesis and Processing, Wuhan University of Technology, Wuhan
40070, China
*[email protected] Keywords: Spark Plasma Sintering, Ultra
high temperature ceramics, Transparent Ceramics, Diamond
Spark plasma sintering (SPS) or electric current assisted
sintering (ECAS) is versatile technique to consolidate ceramic
materials. In SPS, electrical current directly passes through
specimens if conductive, causing a high heating rate commonly
100°C/min, which is beneficial for densification. We have been
developing novel ceramic materials by using SPS. The
characteristics of SPS are capable to sinter hardly-sinterable
ceramics, to sinter perfectly in a short time, and to sinter
materials massively for industrial application. Several research
outcomes are presented.
SiC, ZrB, TiC, TiB2 so-called ultra-high-temperature ceramics
(UHTCs) are difficult to sinter by conventional sintering
technique, while SPS can fabricate these monolithic materials and
their composites can be consolidated. We have fabricated UHTCs such
as SiC-ZrB2, TiN-TiB2, SiC-SiO2 composites by SPS. SPS can develop
high performance high-temperature structural ceramics.
SPS is also advantageous to fabricate transparent ceramics.
Transparent ceramics are a kind of perfect ceramics having density
more than 99 %, and residual pores should be thoroughly eliminated.
Although transparent ceramics can be synthesized by hot-pressing
(HP) or hot isostatic pressing (HIP), it takes a long time and high
temperature. SPS can make transparent ceramics in a short time,
without significant grain growth, resulting in mechanically strong
and