Close Window 1 Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.) This router only has two interfaces. The router interfaces are not operational yet. This router is configured to forward packets to remote networks. The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command. An IP packet received by this router with a destination address of 198.18.8.2 will be forwarded out of the Serial0/0/0 interface. 2 Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.) If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0. If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1. If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Close Window
1
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)
This router only has two interfaces.
The router interfaces are not operational yet.
This router is configured to forward packets to remote networks.
The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.
An IP packet received by this router with a destination address of 198.18.8.2 will be forwarded out of the Serial0/0/0 interface.
2
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0.
If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 172.20.255.1, it will be forwarded out interface S0/0/0.
If RouterC receives a packet that is destined for 192.16.5.101, it will be forwarded out interface S0/0/1.
3 What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
only the Layer 2 source address
only the Layer 2 destination address
only the Layer 3 source address
only the Layer 3 destination address
the Layer 2 source and destination address
the Layer 3 source and destination address
4 If a router cannot find a valid configuration file during the startup sequence, what will occur?
The startup sequence will reset.
The router will prompt the user for a response to enter setup mode.
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last valid configuration.
The router will monitor local traffic to determine routing protocol configuration requirements.
5 Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
VTY interface
console interface
Ethernet interface
secret EXEC mode
privileged EXEC mode
router configuration mode
6 Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing occurs when a router sends the same packet to different destination networks.
Load balancing occurs when the same number of packets are sent over static and dynamic routes.
Load balancing allows a router to forward packets over multiple paths to the same destination network.
Unequal cost load balancing is supported by EIGRP.
If multiple paths with different metrics to a destinations exist, the router cannot support load balancing.
7 What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination MAC Address in the IP Header to look up the next-hop address in the routing table
leaves the Layer 2 frame header intact when decapsulating the Layer 3 packet
uses the destination IP Address in the IP header to look up the next-hop address in the routing table
encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
encapsulates the Layer 3 packet into a special Layer 1 frame and forwards it to the exit interface
8
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)
source IP address: 192.168.10.129
source IP address: BBBB.3333.5677
source MAC address: 5555.AAAA.6666
destination IP address: 192.168.10.33
destination IP address: 192.168.10.134
destination MAC address: 9999.DADC.1234
9 What is the outcome of entering these commands? R1(config)# line vty 0 4 R1(config-line)# password check123 R1(config-line)# login
ensures that a password is entered before entering user EXEC mode
sets the password to be used for connecting to this router via Telnet
requires check123 to be entered before the configuration can be saved
creates a local user account for logging in to a router or switch
10 Which are functions of a router? (Choose three.)
packet switching
extension of network segments
segmentation of broadcast domains
selection of best path based on logical addressing
selection of best path based on physical addressing
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
12
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?
The passwords are encrypted.
The current configuration was saved to NVRAM.
The configuration that is shown will be the one used on the next reboot.
The commands that are displayed determine the current operation of the router.
14
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The destination networks do not exist.
The IP addresses on the router interfaces must be configured as network addresses and not host addresses.
The interfaces must be enabled with the no shutdown command.
Each interface must be configured with the clock rate command.
15 The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network
Which of the following is true regarding CDP and the graphic shown?
CDP running on Router D will gather information about routers A, B, C, and E.
By default, Router A will receive CDP advertisements from routers B and C.
If routers D and E are running different routing protocols, they will not exchange CDP information.
Router E can use CDP to identify the IOS running on Router B.
2 The output of the Router# show interfaces serial 0/1 command displays the following: Serial0/1 is up, line protocol is down. What is the most likely cause for the line protocol being down?
Serial0/1 is shutdown.
There is no cable connecting the routers.
The remote router is using serial 0/0.
No clock rate has been set.
3 Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
ping
show arp
traceroute
show ip route
show controllers
show cdp neighbor
4 A router has one static route configured to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)
It operates at the network layer and allows two systems to learn about each other.
It creates a topology map of the entire network.
It allows systems to learn about each other even if different network layer protocols are configured.
It forwards advertisements about routes for faster convergence.
14 A network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
drops the packet because the destination host is not listed in the routing table
looks up the MAC address of the S0/1/0 interface to determine the destination MAC address of the new frame
performs a recursive lookup for the IP address of the S0/1/0 interface before forwarding the packet
encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface
15
Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1 Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2 Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1 Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2 Altamonte(config)# ip route 198.18.222.0 255.255.255.255 s0/1
WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1 WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1 Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1 Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2 Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/0
Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?
The rate would be negotiated by both routers.
A rate would not be selected due to the DCE/DTE connection mismatch.
The rate configured on the DTE determines the clock rate.
The rate configured on the DCE determines the clock rate.
20
Refer to the exhibit. What two commands are required to provide connectivity between the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)
A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
A(config)# ip route 10.0.0.0 255.0.0.0 172.16.40.2
A (config)# ip route 10.0.0.0 255.0.0.0 s 0/0/0
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
B (config)# ip route 192.168.1.0 255.255.255.0 172.16.40.1
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/1/0
Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?
R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1 R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2 R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2 R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1 R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2
R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.2.1 R2(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
Chapter 3:Dynamic routing
Close Window
1 Which two statements are true regarding the advantages of the use of static routes? (Choose two).
increased security
reduced effort in configuring routes
the administrator maintains control over routing
easier to implement in a growing network
reduces the chance of routing errors
increased router resource usage
2 A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to
the destination network?
The router will install the first route it learned into the routing table.
The router will install both routes in the routing table and load balance between the two.
The router will put the first route in the routing table, and denote the second route as a backup route.
The router will pick the path with the higher bandwidth and will place it in the routing table.
3 When multiple routing protocols have a route to the same destination network, what determines which route is installed in the routing
192.168.252.2 is an interface on the router that produced this output.
13 Which two statements are true regarding classless routing protocols? (Choose two.)
sends subnet mask information in routing updates
sends complete routing table update to all neighbors
is supported by RIP version 1
allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
reduces the amount of address space available in an organization
14 Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers will not allow packets to be forwarded until the network has converged.
Hosts are unable to access their gateway until the network has converged.
Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged.
15 Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network requires a special hierarchical design
fast convergence of the network is crucial
the network is using a hub and spoke topology
the network is using a flat design
there are more than 15 hops between the most distant routers
16 The following line of code is present in the routing table: O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1 What does the number 129 indicate in this output?
The cost for this link has a value of 129.
The clock rate on this serial interface is set to 129,000.
The next-hop router is 129 hops away from this router.
This route has been updated 129 times in this routing table.
17
Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
3
4
56
624
724
18
Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install a RIP route using network A in its routing table because the administrative distance of RIP is higher than EIGRP.
R1 will install a RIP route using network A in its routing table because the path cost from RIP is lower than EIGRP.
R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.
R1 will install an EIGRP route using network B in its routing table because the path cost from EIGRP is lower than RIP.
R1 will install an EIGRP route and a RIP route in its routing table and load balance between them.
19 A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing.
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network
10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.1.0.0/16
10.1.0.0/8
10.0.0.0/16
10.0.0.0/8
6
Chapter 7:
1 What are two functions of the network command used when configuring routing protocols? (Choose two.)
identifies which networks will be included in the routing updates
identifies the hosts addresses that can be summarized in the network
used to list all addresses for remote and local networks
determines which subnet mask to apply to routing updates
determines which interfaces can send and receive routing updates
2 What is the maximum network diameter permitted by the default metric of RIPv2?
15 hops
16 hops
100 hops
120 hops
255 hops
3
Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 is configured on router B?
Routes to the 10.16.1.0/27, 10.16.1.64/27, and 10.16.1.128/27 networks are added.
A connected route to the 10.16.1.128/27 network is added.
A third route to the 10.0.0.0/8 network with RIPv1 as the source is added.
The 10.0.0.0/8 route is dropped immediately from the routing table after router B is configured.
4 A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.)
10.0.0.0/8
127.0.0.0/8
169.254.0.0/16
172.16.0.0/12
192.168.0.0/16
209.165.201.0/27
5 A network administrator installed four new routers that are running RIPv2. Router1 is a boundary router in the RIPv2 network and has a default route configured. Once the network has converged, the network administrator enters Router1(config-router)# default-information originate on Router1. How will this affect the network?
prevents Router1 from forwarding updates about networks that are not directly connected
causes all routers in the network to synchronize routing updates with Router1
forces Router1 to become the primary or designated router (DR) for updates
propagates the default route to all routers in the network
6
Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem?
A gateway of last resort is required.
Subnetting is not supported by RIPv1.
VLSM is not supported by RIPv1.
One of the routers needs a clock rate on the serial interface.
Refer to the exhibit. What can be concluded from the output shown in the exhibit?
The routing table is limited to 2 routes.
The LAN interfaces are participating in the routing process.
One update has been sent out of each serial interface and 2 have been received.
The no auto-summary has not been configured on this router.
8
Refer to the exhibit. RIPv1 is configured as the routing protocol for the network that is shown. The following commands are used on each router: router rip network 10.0.0.0
network 172.16.0.0 When this configuration is complete, users on the LAN of each router are unable to access the remote LANs. Why?
The network statements are configured incorrectly.
A routing loop has been created.
RIPv1 is unable to route to discontiguous subnets of a major network.
RIPv1 is unable to route networks with a /24 subnet mask.
9
Refer to the exhibit. The exhibited network contains a mixture of Cisco and non-Cisco routers. The command debug ip rip was entered on the JAX router. All routers are running the same version of RIP. Router CHI and Router ORL are not able to reach the 192.168.1.16/28 network. What is a possible solution to this problem?
Enable split horizon in the network.
Configure RIPv2 on routers.
Add network 192.168.1.0 to the RIP configuration on the JAX router.
Configure JAX Fa0/0 as a passive interface.
Enable the Serial0/0/0 interface on the JAX router.
Change the IP address on the Fa0/0 interface of the JAX router to 192.168.1.1/24.
Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?
Router1(config)# ip classless
Router1(config-router)# network 192.168.16.0
Router1(config-router)# no passive-interface serial 0/1/1
Router2(config-router)# version 2
Router2(config-router)# neighbor 10.0.0.2
11
Refer to the exhibit. All routers are running RIP version 2. JAX is configured to just advertise the 10.0.0.0/24 network. CHI is configured to advertise the 172.16.0.0/16 network. A network administrator enters the commands shown in the exhibit. What changes will occur in this network?
The JAX router will ignore updates for the 172.16.0.0/16 network due to split horizon issues.
The CHI router will install a route to the 192.168.0.0/16 network in its routing table.
The routing table for CHI will have the 192.168.0.0/16 route but it will have an S next to the route.
The ORL router will apply a 255.255.0.0 subnet mask to all networks in the routing updates it forwards.
They both have the same metric value for infinite distance.
They both use a broadcast IP address to send updates to their neighbors.
They both send subnet mask information in their updates.
They both provide for authentication of update sources.
They both use split horizon to prevent routing loops.
16 RIPv2 is the configured routing protocol on the routers in a network. The command Router(config-router)# no version 2 is entered on the routers. What effect does entering this command have on routing updates?
Subnet masks will be added to the routing updates.
Routing updates will be sent out using multicast address 224.0.0.9.
Version 1 and 2 updates will be received and the version 2 updates will not be sent.
The RIP routing process will be removed from the router and routing updates will not be forwarded.
17
Refer to the exhibit. What effect will the commands that are shown have on RIP updates for Router1?
Only version 2 updates are sent to 255.255.255.255.
Only version 2 updates are sent to 224.0.0.9.
Both version 1 and version 2 updates are sent to 224.0.0.9.
Both version 1 and version 2 updates are sent to 255.255.255.255.
18 What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)
RIP version 2 supports VLSM.
RIP version 2 supports more than 16 routers.
RIP version 2 supports classful (and not classless) routing
RIP version 2 supports routing update authentication.
RIP version 2 supports multi-areas.
RIP version 2 uses the Dijkstra algorithm rather than the Bellman-Ford algorithm.
Refer to the exhibit. A technician needs to add a new loopback interface to test routing functionality and network design. The technician enters the following set of commands on the router: Sanford(config)# interface loopback1 Sanford(config-if)# ip address 192.168.6.62 255.255.255.252 Why does the router respond with an error?
The router does not allow loopback interface configurations.
This mask can not be used with this class of addresses.
Classless routing must be configured before this address can be added.
The network address for Loopback1 overlaps with an already configured interface address.
The router is over the limit for the maximum paths that can be provided in the routing table.