90 Terminal block accessories Clutch Lock Terminal Blocks PLC Interface Terminal Blocks Rail Type Terminal Blocks Assembly Terminal Blocks Special Purpose Terminal Blocks Terminal Block Accessories Line-up Stud support / copper bar for branching Terminal block accessories Terminal block accessories Stud support Copper bar for branching This is suitable for as support of bus bar and copper bar for branching. The stud made from galvanized steel resistant to corrosion supports firmly the bus bar and copper bar for branching. As the base part is phenolic molding compound, it is very strong. The stud has a strong fit drive mechanism, so it does not spin free. The nut and spring washer for securing are included. As it is for supporting, it cannot be conducted. TS 100 CHM TS 200 CHM TS 600 CHM Type name Diameter of stud TS 100 CHM TS 200 CHM TS 600 CHM M 8 M10 M12 Ambient temperature Relative humidity Insulation resistance Commercially available cycle withstand voltage -20 to +40℃ (No freezing or condensation) 45 to 85% 100M Ω or more (500V Megger) 2500V 1 minute Cramping torque (N・m) 8 to 10 15 to 20 25 to 35 General mass (g) 40 80 130 Type name Diameter of stud TS 11 TS 12 TS 21 TS 22 100A 200A Number of screw holes 10 20 10 20 General mass (g) 90 180 160 260 Number of contents 10 pieces Diameter of screw M5 Cramping torque 2.2 to 2.8 N・m ■ Dimensions (Unit: mm) TS 11 TS 12 TS 21 TS 22 ■ Dimensions (Unit: mm) This can divaricate small current circuit and control circuit in various branch. This can be a branching terminal block by supporting with TS series stud terminal block. In order to improve the contact dependability, nickel is plated on copper bar. M5 tap M5 tap Thickness 4mm Thickness 4mm Thickness 4mm Thickness 4mm
10
Embed
Terminal block accessories - · PDF fileTerminal block accessories Clutch Lock Terminal Blocks PLC Interface Terminal Blocks Rail Type Terminal Blocks Assembly ... TTB 1S The cover
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
This is suitable for as support of bus bar and copper bar for branching.The stud made from galvanized steel resistant to corrosion supports firmlythe bus bar and copper bar for branching.As the base part is phenolic molding compound, it is very strong. The studhas a strong fit drive mechanism, so it does not spin free.The nut and spring washer for securing are included.As it is for supporting, it cannot be conducted.
TS 100 CHM TS 200 CHM TS 600 CHM
Type name Diameterof stud
TS 100 CHMTS 200 CHMTS 600 CHM
M 8M10M12
AmbienttemperatureRelative humidityInsulation resistanceCommercially availablecycle withstand voltage
-20 to +40℃(No freezing or condensation)45 to 85%100M Ω or more (500V Megger)2500V 1 minute
Cramping torque(N・m)
8 to 1015 to 2025 to 35
General mass(g)
4080130
Typename
Diameterof stud
TS 11TS 12TS 21TS 22
100A
200A
Number ofscrew holes
10201020
Generalmass (g)
90180160260
Number ofcontents
10 pieces
Diameterof screw
M5
Cramping torque
2.2 to 2.8 N・m
■ Dimensions (Unit: mm)
TS 11 TS 12
TS 21 TS 22
■ Dimensions (Unit: mm)
This can divaricate small current circuit and control circuit in various branch.This can be a branching terminal block by supporting with TS series stud terminal block.In order to improve the contact dependability, nickel is plated on copper bar.
5 sets of A/B5 sets of A/B5 sets of A/B10 pieces10 pieces10 pieces10 pieces10 pieces
5 sets of A/B5 sets of A/B
5 sets of A/B
End plate
This is used for terminal of assembled terminal unit. When two sheets are used for both ends, they also work as stopper of sticker. Furthermore, it is also possible to use one sheet for one side by bending and removing the lug for pressing sticker.
Use one sheet for the terminal of assembled terminal unit. However, it is not necessary for TR200 and TR400. As the N type has no groove for leading name sticker, it is possible to use two sheets for both ends to use them as stopper of sticker too.
The end plate is used for terminal of assembled terminal unit. Furthermore, it also works as a stopper of name sticker. Each sheet for right and left is one set.
(for TW Series)
TXA1
Sticker pressing lug
When two sheets are used for both sides
44.55.544.579115.5105.5105677.59111112697
Note: End plate general mass is total of right and left 2 plates (1 pair).
■ Cover of assembled terminal block (part for maintenance)
■ Insulation barrier
Cover
This cover is made from transparent polycarbon-ate, and set-in type. For TX100 or greater models, 3P dedicated products are also available. TT10SK type can be attached to upper stage only, TT20K and TTJ8N types can be attached to both of upper stage and lower stage.
Width x length(mm)
TXB 1TXB 1 LTXB 2TXB 2 L
TRB 1TRB 1 LTRB 2TRB 2 LTRB 3TRB 3 LTRB 6TRB 10 N
TRB 20 NTRB 40 NTRB 10 N 03TRB 20 N 03TRB 30 N 03TRB 40 N 03TRB 60 N 03TTB 1 STTB 1 SLTTB 2TTB 2L
It is possible to set the terminal No. etc. on it. As the partitioning line is printed for TXC type, it is possible to attach it to terminal unit after setting a seal on it, and it is very convenient.
Dedicated 5.5 width × 1m made of fiber, sold by one piece (Thickness 1mm)Dedicated 6.5 width × 1m made of fiber, sold by one piece (Thickness 1mm)Dedicated 9.5 width × 1m made of fiber, sold by one piece (Thickness 1mm)Dedicated 9.5 width × 1m made of fiber, sold by one piece (Thickness 1mm) - - - - -(TRC 11, 12 are used)(TRC 11, 12 are used)(TRC 21, 22 are used)(TRC 21, 22 are used)
Type name of terminal block name sticker
■ Name sticker of terminal block (part for maintenance)The name sticker of assembled terminal block is prepared as a part for maintenance.
Remarks:1. Use the steel rail after applying rust resisting coating material to cut surface.2. When you use the rail leaving long, the intensity increases adequately by securing a few points not only both ends.
There are four types of rails (IEC 35mm width, IEC 15mm width, C type, IEC / C type dual purpose).IEC 35mm width rail has an alumi-num type and steel type.
Slim typeResinStandardLarge type2 points fixing-Large type
Attach this to both ends of assembled terminal unit to fix the unit to rail firmly. It is also possible to attach or remove from surface of rail.
Remark:As TXE2 has a unit-fixing bracket, it is possible to fix the terminal firmly.Especially, it is optimum for large type terminal block of TX30 or greater. For TT Series (2-stage type terminal block), it is fixed more firmly by attaching TXE2C (accessory plate) additionally.
Set the screw on rail after warming it enough.The screw is fixed by securing it pressing the screw head with screwdriver.
TXE 1
TXE 2
TXE 4
TXE 2C
TRE 1
TXJE 1
TWE 1 JTXE 3
● How to attach TXE1 and TXE2
The configuration of these stoppers is new type, so the rail is shorter and more compact than those of existing products.As it is fixed by securing the screw lightly, take care not to secure the screw too much. Check the both legs of bracket hang on the edge of rail completely.
● How to attach TXE4, TXJE1, TWE1, JTXE3 and JTXE5
127.5
47 12
237.5
1247
18.726
1.2
22.5
45
21
43
9.57.5
M4×10(± Pan head small screw)
187.5
45
9
2010
24 14
95
823
6
7.5
17
47
640.5
46
25.5
4
6.5
TWE2
40.5
5
11.537
45
9
307.
5
34
96
Terminal block accessoriesC
lutch
Lo
ckT
ermin
al Blo
cksP
LC
Interface
Term
inal B
locks
Rail T
ype
Term
inal B
locks
Assem
bly
Term
inal B
locks
Sp
ecial Pu
rpo
seT
ermin
al Blo
cksTerm
inalB
lock Accessories
Lin
e-up
■ Dimensions (Unit: mm)
Rail support
Remarks:1. TRGC1A, TRGC2A, and TRGC3A are the one that the rail attachment parts of TRGC1, TRGC2, and TRGC3 are bent by 30°.2. As there is a hole of φ 4.3 (prepared hole of M5) is allocated at the neck part of TRGC3 and TRGC3A, it can be used as an attachment hole of rail or other equipment.
This makes wiring easy by suspending the rail or changing the attachment angle.With this, it is possible to attach the terminal block to corner of board or narrow attachment space.
This is a transfer bracket convenient for common wiring. There are three types (2- pin, 6-pin, and 20-pin), and each type can be cut for required number of pins by wire cutter etc. The material is brass nickel plating. You can select the short bar from three types below.
Remarks:1. For details on short bar for clutch lock terminal block, please refer to“Clutch Lock Terminal Block”.
2. There are short bars of different types other than the ones shown in the table below. For details, please refer to the catalogue of "parts for board".
3. Use the short bar so that the total current of every pin which short-circuits is conducting current or less of short bar.
Type name No.of pins Rail type terminal block Assembled terminal block
This is a tool to remove the unit attached to DIN rail (TXDA2, TNDS2). This can be used for TX7 to TX20 and TXU7 to TXU20.
Unit removing tool
Product name Type name
TXKRemoving tool for Series TXApplicable unit
TX7 to 20, TXU7 to 20
Insert this into the gap between electric cable and mark tube to prevent the slip or falling of mark tube.When shipped from factory, as 10 pieces are connected in one set, cut it when you use.
Line number stopper
This is an adapter for checking conducting.It is possible to insert tester pin or alligator clip in it.Furthermore, the cap that protects terminal part is included.(As there is a strap hole, it is possible to prevent the loss of cap by connecting it to main unit with a rope.)
Check adapter
This is a tool for connecting the electric cable of crimptype terminal dedicated type (TWY10, TWY16).
Electric cable connecting tool(for TWY Series)
Product name Type name
TWYT 1Electric cable connecting tool for TWY
Wire connection tool
Tools to connect independently to modular type plug.
Push
TWSB1
TWSB2
(Example of use) External dimensions (Unit: mm)
Before delinking (10 trains)
Approx 90
8
1.2
20
7.4
0.6
28.5
22.3
14.9
52.9φ2.5
φ2.5
General mass (g)
Wire connection tool for TWS10 TWSB 1Wire connection tool for TWS20 TWSB 2