BHAGALPUR COLLEGE OF ENGINEERING, BHAGALPUR. TEQIP-II Agenda for discussion and approval 1. To get approval for the appointment of consultant for NBA Accreditation in Civil, Electrical and Mechanical Engineering. At least 60% of ourUGprogrammes should be accredited. Accreditation are awarded based on the sufficient Infrastructures, Student Faculty Ratio, Faculties Qualifications, and others College Activities. Accreditation 1 is a formal, third party recognition of competence of our Colleges.In NBA, the Course will be a ccredited based on courses. The Department of Science and Technology is very keen to move for accreditation of Civil, Electrical and Mechanical Engineering course. The accreditation fees for 3 Course will be Rs 9.00 lakhs. Accreditation is essential to promote quality conscious where excellence, relevance to market needs and participation by all stake holders are prime and major determinants. It is important to set the quality benchmarks targeted at global and national level. We have to make evaluation and self-assessment of our programmes mentioned above. Therefore, it is urgent need to appoint 1 The vision of the NBA is “to be an accrediting agency of international repute by ensuring the highest degree of credibility in assurance of quality and relevance of professional education and come to the expectations of its stakeholders, viz., academicians, corporate, educational institutions, government, industry, regulators, students, and their parents
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
BHAGALPUR COLLEGE OF ENGINEERING, BHAGALPUR.
TEQIP-II
Agenda for discussion and approval
1. To get approval for the appointment of consultant for NBA Accreditation in Civil, Electrical and Mechanical Engineering.
At least 60% of ourUGprogrammes should be accredited. Accreditation are awarded based on the sufficient Infrastructures, Student Faculty
Ratio, Faculties Qualifications, and others College Activities. Accreditation1 is a formal, third party recognition of competence of our
Colleges.In NBA, the Course will be accredited based on courses. The Department of Science and Technology is very keen to move for
accreditation of Civil, Electrical and Mechanical Engineering course. The accreditation fees for 3 Course will be Rs 9.00 lakhs.
Accreditation is essential to promote quality conscious where excellence, relevance to market needs and participation by all stake holders are
prime and major determinants. It is important to set the quality benchmarks targeted at global and national level. We have to make evaluation
and self-assessment of our programmes mentioned above. Therefore, it is urgent need to appoint consultant for preparing the self-appraisal
reports of our Institution based on guidelines, norms and standards specified by NBA.
2. To seek approval of revised procurement plan for the different departments
Enhancing the laboratories towards the successful transformation into the Centre of excellence. Establishing the research culture in the institute
for collaborative working of various departments. Effectively executing the procurement policy in tune with the Guidelines of World Bank and
associated government bodies for more transparent and fair procedure for which approval from SPFU and NPIU is also necessary.
S.No.
Activities Total
Allocation
Permissible Expenditure
Infrastructure improvements for teaching, training and learning through
1The vision of the NBA is “to be an accrediting agency of international repute by ensuring the highest degree of credibility in assurance of quality and relevance of professional education and come to the expectations of its stakeholders, viz., academicians, corporate, educational institutions, government, industry, regulators, students, and their parents
1. Establishment of new laboratories and strengthening of existing for PG programs, faculty research, etc.Procurement of furniture.Details are in Annexure 1.
480 Lakh
a) New equipment and furniture: establishing new PG laboratories and strengthening of
existing laboratories Faculty research and institutional consultancy work Campus‐Wi Fi networking of academic and
administrative buildings, hostels and faculty Residences.
Course‐specific Software (Rs. 50.00 L).
Modernization and Strengthening of Libraries (Rs. 50.00 L):
Procurement of print and digitized books, e‐journals Expenditure for digitization of library books Establishment of CD bank Membership of INDEST - AICTE consortium (The
Ministry of Human Resource Development has set-up the Indian National Digital Library in Engineering Sciences and Technology (INDEST) Consortium.The consortium headquarters set-up at the IIT Delhi. Besides, 44 Government or Government-aided engineering colleges and technical departments in universities have joined the Consortium with financial support from the AICTE. Moreover, the INDEST Consortium, as an open-ended proposition, welcomes other institutions to join it on their own for sharing benefits it offers in terms of highly discounted rates of subscription and better terms of agreement with the publishers. The Consortium has an active mailing list and a Web site hosted at the IIT Delhi).
Civil Worksrefurbishment of existing structures/ spaces to create new laboratories for PG programs and research as per the need ( Rs 5.00 Lakh)
2 Updating of learning resources
3 Modernization and strengthening of libraries and increasing access to knowledge resourcesDetail in
Annexure 24
Refurbishment (Minor Civil Works)
5 Providing Teaching and Research Assistantships for significantly increasing enrolment in existing and new Masters and Doctoral programs in Engineering disciplines
100.0 L
TEQIP Scholarships (Rs. 25.00 L): Teaching and Research Assistance ships for Master’s students in engineering disciplines who are not getting any other Scholarships or those who are not sponsored by any company.
Developing research interest among UG students Fiscal incentive to students that voluntarily associate
with industry oriented R&D projects and Travel cost of students that associate with an industry for about 3‐4 weeks during vacations to continue work on R&D projects.
Registration Fees for UG students attending National Conferences for presenting Research Paper or Attending a STTP useful for Research.
Inviting expert Lecturers from Research Institutes to contents other than Syllabus related to research topics.
6 Enhancement of R.& D. and institutional consultancy activities
20.00 L
1. Enhancement of R.& D. and Consultancy securing sponsored projects and consultancy
assignments Publication of research papers in per reviewed
journals commercialization of research products
patenting of research products Travel cost, hospitality and honorarium
paid to Consultant for participation inR & D and for delivering Expert lectures
2.Organizing National and InternationalConferences (Bihar and all the States in the Indo-Gangetic plane have very nice ravine sediments deposited along the banks of Ganga and other rivers. These are very good material for brick making. There are so many brick kilns along the banks of rivers. The construction of houses with this technology would reduce the cost by about 35 %. The
houses built in such a fashion with a seismic belt would be seismically stable, climatically suitable and environment friendly. It is purposed to arrange a national seminar on Key Hole Brick Technology within next two / three months at Patna through a one day conference or Seminar. The cost would be approximately Rs 5.00 Lakh.
Hospitality to participants Venue and logistic arrangements Replication of printed training materials Publication of proceedings Travel, boarding & lodging for
invited experts3. Seed Money for Research Projects
Seed money for good innovative projectsfor equipment and consumables
7 Faculty and Staff development for improved competence based on TNA Annexure 3
100 L
Faculty Qualification Up gradation1. Fees charged for course work and use of research facilities; and consumables by the institution where faculty is enrolled for qualification up gradation either through fulltime or part‐time or by sandwich scheme.2. Consumables, if faculty is registered for qualification up-gradation on full‐time or part‐time basis within the parent Institution
b) Subject knowledge and research competence up-gradation of Facultyas planned through TNA• Course fee; travel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when faculty is deputed out‐station to another institution (within India or abroad) for the duration of the course, travel time and the time permitted by the BoG (for travel abroad) and by Principal (for National Travel) for visits to institutions/organizations of interest and relevance to the
faculty• Course fee and local travel expenses as per applicable norms and rules when faculty attends a course in‐station but at an institution other than the parent institution
c) Resource sharing through collaborative arrangements• Travel expenses; boarding, lodging, and sundry expenses/allowances for faculty visiting institutions and industries within India to develop and implement joint projects with well-defined deliverables.• Hospitality, local travel, for Faculties visiting from other institutes to BCE Bhagalpur for guidance and collaboration
d) Organizing subject area Continuing Education Training Programs,Workshops2, seminars3 as per norms decided by the BoG.• Hospitality to participants• Venue and logistic arrangements• Replication of printed training materials• Publication of proceedings• Travel, boarding & lodging for invited experts• Honorarium for delivering lectures and training in BCE BhagalpurTraining of Technical Support Staff• Course fee; travel expenses; boarding, lodging, and sundry expenses 4as per applicable norms and rules when the technical support staff is deputed outstation to another organization within India and travel time• Course fee and local travel expenses as per applicable norms and rules when training is attended in‐station but at an
2 A four days workshop organised on composite course on earthquake which covers the following aspects: Scientific aspects of earthquake, Engineering aspects of earthquake, Disaster management aspect of earthquake, and Tsunami. Further, a two week course has been organised by NITTR Kolkatta on Pedagogy.
3 Bihar and all the States in the Indo-Gangetic plane have very nice ravine sediments deposited along the banks of Ganga and other rivers. These are very good material for brick making. There are so many brick kilns along the banks of rivers. The construction of houses with this technology would reduce the cost by about 35 %. The houses built in such a fashion with a seismic belt would be seismically stable, climatically suitable and environment friendly. It is purposed to arrange a national seminar on Key Hole Brick Technology within next two / three months at Patna through a one day conference or Seminar.4 Expenditure incurred in attending International Seminar on the 6th Conference of the International Society for Integrated Disaster Risk Management (IDRIM -TIFAC 2015) held in Delhi during October 28-30, 2015 is Rs 25,000/-. It was attended by Principal, Dr Nirmal Kumar.
institution other than the parent institution
Group Training Arranged for Faculty/Staff Fees for participants, transport, food, etc. for the training programs arranged by the Institute in collaboration with Industry or some outsourced partyReimbursement of travel cost for the faculty5, who attend International and National Conference in India and Abroad.
8 Enhanced interaction with industry
Rs 40 L
Increasing Industry-Institute-Interaction• Travel cost, hospitality and honorarium paid to industry personnel for participation in curriculum development/revision/restructure, student assessment and institutional bodies, and for delivering expert lectures• Expenditure for increasing Institute Industry Interaction
Placement Activities for Students• Expenditure towards inviting industries (excluding travel cost and lodging boarding) for campus interviews and hospitality during campus interviews• Arranging tutoring by industry experts to prepare students for on‐ and off‐campus job interviews
9 Institutional management capacity enhancement
Rs 30.00 Lakh
Training of Institution Officials and Senior Faculty and Orientation of BoG Members6
1. Course fee; travel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when deputed outstation to another institution (within India or abroad) for the duration of the course, travel time and the time permitted by the BoG (for travel abroad)/ by Principal for National Travel for visits to institutions/ organizations of
5 Expenditure incurred in attending Training Course by Dr Nagendra Choudhary may be approved amounting to Rs 20000.00 ( Twenty thousand) only.6 Expenditure incurred on visit of Prof Jaiprakash , Mentor from 25-27th October 2015 may be approved amounting to Rs 50000.00 ( Fifty thousand) only.
interest and relevance to the faculty in the vicinity of the location of training2. Trainer’s fee and overheads; and sundry expenditure if training programs organized within the parent institution.3. Travel costs, boarding and lodging expenditure and sitting fee to Board members; sundry expenses on organizing Orientation program.Study ToursTravel expenses, boarding and lodging, and sundry expenses/allowances as per applicable norms and rules when deputed for study tour within India or abroad for the duration of the tour and travel time.
10 Implementation of Institutional reforms
Rs 20 L
Curricular ReformsTravel cost, hospitality and honorarium paid to industry personnel for participation in curriculum development/revision/restructure & reforms; Sundry expenditure on holding meetings of the concerned committees.
Accreditation: Accreditation fee to NBA
11 Academic support for weak students( Annexure 3)
Rs 40.00 Support to Academically Weak Students Psychological Services and Support for Needy
Students for coping with the institutional environment.
Support for Students to Improve their Employability
Honorarium to faculty and staff for taking bridge courses,
remedial teaching classes and skill development training and
TA, DA to outside experts for specialized training in soft
components including communication‐ presentation skills
12 Incremental Operating Cost
Rs 100.00 Lakh BoG and other Committee Meetings
TA & DA for faculty and staff attending workshops, Meetings and training in the World Bank procedures as organized/arranged by the NPIU and SPFUs
Occasional hiring of vehicles for project related work only
Salaries of additional full‐time regular and contract faculty and staff appointed against posts created under the Project
In‐house maintenance of existing and new equipment
Maintenance of equipment including computers and related devices and assets provided under the Project through Annual Maintenance Contracts
Office operation including stationery, postage, electronic communication, telephone, electricity, water, etc.
consultancy Services engaged for technical assistance related to procurement of Civil Works and equipment, pedagogical training, mentoring, hand‐holding for Project implementation as required by weak institutions, external financial auditing
Contract fee for outsourced services Procurement related expenses I,e.; Advertisement,
related stationary, photography, video shooting, and hospitality charges.
2 Grinding machine Grinding machineWorking-01, Not working-01
2. Spot welding machine
01 1,50,000 1,50,000
3 Drilling machine Drilling machineWorking-01, Not working-02
3. Cuppola furnace 01 1,00,000 1,00,000
4 Vertical shaper machine Vertical shaper machineWorking-01, Not working-03
4. CNC Lathe.
Technical Specification:
DNC Based PC-Controlled horizontal bed lathe. Machine complete with fully enclosed working area, safety units according to CE- regulations steeples adjustable main drive, 8- station tool turret, manual tailstock
01 9,00,000 9,00,000
automatic movement to the reference position electrical and mechanical preparation for automation connection cable PC machine, disk with machine data Must be programmable through control keyboard designed as per industrial control & control software like: Operation : Control Keyboard same as industrial control units Preparation for the exchange to other control systems.Control Systems
1. SIEMENS & GE FANUC
2. CAD/CAM
Working area should not be less than dimensions given below.
1. Swing over bed (mm) ∅ 125
2. Swing over cross slide (mm) ∅ 55
3. Max machining diameter (Chuck parts with tailstock) (mm) ∅50
4. Max. Parts length (mm) 215
Travel
1. Travel in X- axis
(mm) 452. Travel in Z- axis
(mm) 225
Main Spindle
1. Spindle nose according factory standard
2. Spindle bone (mm) ∅ 15
3. Chuck diameter (mm) 70
4. Hole to chuck (mm) ∅ 15
5. Speed range (rpm) 120-4000
6. Mechanical spindle speed 2
7. Max. torque (Nm) 14
Main drive
1. AC – motor,2. Speed range
(rmp) 1200 to 14000
Tool turret (Important)
1. Number of tool stations -8
2. Tool holding inside/outside -4/4
Feed drives
1. 3 phase step motor
2. Rapid traverse in X/Z
Tailstock
1. Quill stroke (mm) 35
2. Quill diameter (mm) 22
3. Internal taper MT 1
DNC- interface
1. For remote control via a software protocol. The communication in done via the Rs. 232 interface for the FMS/CIM – operation
Safety equipment
Machine full covered axis limit switch door limit switch emergency according CE standard
Documentation
1. Machine description
2. Software Manual3. Electrical
documentation4. Training manuals5. Teaching material
5 Forge heating Equipment Forge heating EquipmentWorking-01, Not working-09
5. CNC Milling MachineTechnical
1 12,50,000 12,50,000
Specification
DNC based PC – controlled 4-axis milling machine for universal CNC training with 8- station tool turret machine complete with fully enclosed working area, step less adjustable main drive automatic movement tc the reference
Must be programmable through control keyboard & software like,
Operation : Control Keyboard same as industrial control units, preparation for the exchange to the control systems:
Control System
1. Siemens & GE Fanuc
2. CAD/ CAM
Technical data of the machine (not less than)
Working area,
1. Longitudinal travel (X-axis) (mm) 175
2. Cross travel (Y-axis) (mm) 125
3. Vertical travel (Z-axis) (mm) 250
Milling table
1. Clamping surface (L x W) (mm) 400x 120
2. 2 T- slots
Tool system
1. Tool magazine pick-up system with swivel arm on the left of the milling head placed. Blow out facility.
2. System drive electr, mech.
3. Tool clamping automatic
4. Number of tool station 8
Main drive
1. Asynchronous AC motor,
2. Speed range (Step less) (U/min) 150
Feed drive
1. 3 phase step motor in x/y/z axis
2. Feed rate and rapid traverse in x/y/z
4th axis (c -axis)
1. Continuously controlled
2. Spindle height
40mm3. Displacement
20mm4. Retrofit able
DNC- Interface
1. For remote control via a software protocol. The communication is done via the Rs. 232 interface for the FMS/CIM – operation
Safety equipment
1. Machine full covered, axis limit switch door limit switch emergency off switch
2. According CE standard
Documentation
1. Machine description
2. Software manual3. Electrical
documentation4. Training manuals5. Teaching material
6 Milling machine Milling machine- Not working
6. Electric welding machine (Memco)
1 1,20,000 1,20,000
7 Spot welding machine Spot welding machine-Not working
7. Welding Helmet 10 500 5,000
8 Cuppola furnace Cuppola furnace-Not working
8. Hand Screen 10 400 4,000
9 CNC Lathe CNC Lathe- Not working 9. Black Glass 20 200 4,000
10 CNC Milling Machine 10. White Glass 40 100 4,000
11 Electric welding machine (Memco)
11. Cable Clamp 10 100 1,000
12 Welding Helmet 12. Welding holder 08 500 4,000
13 Hand Screen 13. Earth Clamp 02 500 1,000
14 Black Glass 14. Chipping Hammer
10 200 2,000
15 White Glass 15. Wire Brush 20 100 2,000
16 Cable Clamp 16. Gas Welding Trolly
01 10,000 10,000
17 Welding Holder 17. Gas Cylinder (Oxygen) with regulator
Sl. Name of Equipment’s Qty. Rate/unit in Rs. (Approx)
Amount in Rs. (Approx)
1 Vapour Compression Unit Mechanical Heat Pump Test Rig
01 70,000 70,000
2 Vapour Compression Unit Test Rig-Cycle of Refrigeration
01 70,000 70,000
3. Domestic Refrigeration R- 43 01 30,000 30,000
4 Air Conditioning – Test Rig 01 70,000 70,000
5 Ice Plant Test Rig 01 70,000 70,000
Total (Rs.) 3,10,000
TEQIP –II
SL NO NAME OF LABORATORY AMOUNT (Rs.)
1 STEAM POWER LABORATORY 10,00,000
2 CAD/CAM LAB. 27,96,200
3 REFRIGERATION LAB 3,10,000
TOTAL (Rs). 41,06,200
B. Civil Engineering DepartmentList of Machines/ Equipment’s
S. No Name of equipment’s Specification Qty. Rate Amountincluding VAT
Total Amount (Rs.)
Concrete Lab.1 Compression testing
MachineAnalogue Compression Testing Machine, Capacity 2000kN,Electrically Operated, Single Gauge confirm IS – 14858 (2000), ASTM – C-39, AASTHO –T-22 with NCCBM certified load gauge. Loading Unit: Electrically operated fully welded of steel cross head and machined steel base with solid support plates. The hydraulic jack of 2000kN capacity is fixed on the base. The upper platen has got a self-aligning action. The lower platen rests on the jack ram and is positioned centrally with the help of a centering pin. Loading is accomplished by the upward movement of the lower platen. Both the lower and the upper platens are hardened, ground and polished. Guidelines are marked on the lower platen to keep the specimen centrally and co-axially with the hydraulic jack. A dust cover is provided on the jack to prevent any dust going into the cylinder of the jack. Four spacers with locating pins are provided to be inserted in between the lower platen and the hydraulic jack to reduce the excessive gap between the two
1 3,50,000.00
platens when small specimens along with brick platen are required to be tested. Motorized Pumping Unit :Motorized pumping unit of 2000kN is housed in an elegant cabinet and is of two speed design driven by an electric motor. A connector is fixed to connect the motor to the mains through ON-OFF Push Button Switch. Slow and fast lever which is fitted with a knob. To and fro movement of this lever, coarse adjustment of rate of loading can be done. Fine adjustment can be done by rotating the knob fitted on this lever. Release valve preferred to be provided on the top of the pump. Pressure can be released by unscrewing the knob. Oil reservoir is fitted with oil filler plug cum dipstick , drain plug , and safety valve The unit is suitable for operation on 220volts, 1 phase, 50 cycles AC supply.3General Specification:Least Count : 10 Kn.Accuracy: +- 1%Platen max clearance: 370 mm.Upper swiveling arrangement. Side plate distance ( Max) : 340 mm Size of platen: 222.0 mm dia. Platen hardness: 60 BHN Piston dia : 222.2 mm. Piston stroke : 50 mm.Specimen sizes : 70.6mm,100mm, 150mm Cube and cylinder.Frame stiffness : 3000 KN / mm.Weight :1500 KG aprox.Painting: Powder coating with a minimum thickness of 75 micron.Pump noise level : within 65 dbSample viewing port: 305 x 460 mm with poly acrylic transparent sheet.NABL Calibration with traceability Certificate
2 Flexure Testing Machine 100kN Flexure Testing Machine Electrically Operated, are designed to test flexural strength of concrete beams. The design provide maximum rigidity throughout their working range. The load is applied by the downward movement of the piston. A spacer is provided for testing different size of beams. The load is indicated on a calibrated bourdon tube type load gauge of range : 0 -100 kN x 0.5 kN,The load gauge is calibrated against National Physical Laboratory / National Council for Cement and Building Materials certified proving ring. Light weight, rugged high strength frame • Double action hydraulic pump • Self-aligning roller assembly • Hydraulic jack provided with retraction spring,• For testing beams of 100X100X500mm and 150X150X 700mm. Suitable for operation on 220V, 50Hz, Single Phase, AC supply (For Electrically Operated Flexure Testing Machine).Least count-0.5KN,center distance between supporting roller for various beam size,600mm and 400mm. center distance between loading roller for various beam size-200mm and 133mm.
1,50,000.00
3 Concrete Permeability Apparatus,
Concrete Permeability Apparatus, 3 Cell model for 150mm cube as per IS 3085 with Compressor 15kg/sq cm capacity
1,34,000.00
4 Air Entrainment Apparatus,
Air Entrainment Meter Capacity 0.005m3 (5 litres) suitable for aggregate size upto 38mm, consists of a pressure-tight flanged cylindrical measuring bowl, fitted with a removeable flanged and a conical cover assembly with a seal in-between. The conical cover hasan air valve and a pet cock for bleeding-off the water. A cylindrical stand pipe, which is graduated in per cent air content, is fixed on the conical cover assembly. Required pressure is applied to the specimen with the help of a pressure bulb. The whole assembly is mounted on a flat base. Each apparatus is supplied complete with a calibrating cylinder, pressure gauge, funnel, trowel and tamping bar.
23,000.00
5 Fatigue Testing Machine Maximum bending moment kg.cm 200 bending moment adjustable kg.cm 25-200 ranges kg. cm 5-125 gripping dia of specimen 12mm, testing dia of specimen 8mm rotating speed 4200rmp, accuracy of applied bending moment +- 1% digital counter 8 digit, power required Hp 0.5, main supply 3ph, 415V, 50Hz, AC, overall size (approx) 1000L x 5000W x 600H weight (approx) 120kg.
1,80,000.00
6 Tile Abrasion Testing Machine
Tile Abrasion Testing Machine for tile sample is pressed under a specified load against a grinding path, strewen evenly with an abrasive powder, revolving at the rate of 30 ± 1 rpm. At the end of 100 revolutions of the disc, the second parallel side of the tile is subjected to wear an equal number of revolutions of
the disc. The wear of the tile is measured using AIM48101 thickness measuring device (which is supplied at extra cost). The Abrasion Testing Machine consists of a replaceable
1,39,350.00
grinding path, fitted on to a disc rotating
about its vertical axis. The rotating disc and the grinding path are enclosed by a circular tray. A bracket holds the specimen. The loading is by a counterbalanced lever. Afunnel is provided to facilitate charging the grinding path with abrasive powder. Supplied complete with automatic pre-set revolution counter and one 7.5 kg weight, but without abrasive powder and thickness measuring device.
Suitable for operation on 415 V, 50 Hz, 3 phase,AC supply7 Compaction Factor
ApparatusCompaction Factor Apparatus for determination of workability determination of concrete mixes of very low workability such as those normally used with concrete, compacted by vibration. Concrete mix having maximum size of aggregate not exceeding 38 mm, can be tested for workability. Compaction Factor Apparatus is complete with hoppers and receiver assembly, Tamping Rod of 16 mm dia X 60 cm long having a Hooper and two trowels.
23,000
8 Cement Tensile Testing Machine
This cement tensile testing machine is primarily used to determine the tensile strength of briquette specimens of cement it can also be used to test the flexure strength of the sample. This test is commonly used by cement manufacturers in order to determine the quality of cement. Capacity 2kN&10kN, Loading speed of the single lever system 10+_ N/Sec, loading speed of the double lever system 50+- 10/sec flexure jaw diameter of the loading roller 10mm supporting roller diameter 10mm supporting roller distance 100mm barrel plate span 46mm
2,56,109
9 Concrete Mixer, Pan Type, Capacity 40L
Concrete Mixer, Pan Type, Capacity 40L 2,41,400
Rs. 1496859.00Transportation Engg. Lab.
10 Benkelman Beam Benkelman Beam with Digital Dial Gauge in Wooden Carrying Case (as per IRC:81), Lightweight aluminium construction.• Ease of Transportation. • Unique Telescopic Design, simplifying field set up. • Compact, thereby reducing the amount of storage space needed. Benkelman Beam utilises the technique of using balanced beam in conjunction with a suitable vehicle to measuring road flexure. The improved Benkelman Beam is a convenient, accurate device for measuring the deflection of flexible pavements under moving wheel loads. Operating on a simple lever arm principle, the unit consists of a Reference Beam, Body, two part Probe Beam and Rear Zero adjust.
38,500.00
11 Flash Point Apparatus Flash Point (Open) and Fire Point Cleveland, ElectricalHeating Thermometer IP 28 C,Range : -6°C to+110°C, Ref. Standards - IS:1448 (Part 69), ASTM D 92, IP 36,BS:4689, ISO 2592,For determining the flash and fire
13,120.00
points of petroleum products, except for fuel oil and those products which have open cup flash point below 79° C (175° F).consisting of Cleveland Flash Cup Brass, with anInsulated Handle. Gas Test-Jet Assembly Correctly positioned and pivoted from a cast cup platform which is fixed to a heating bath. Energy Regulator, To regulate the rate of rise in temperature 220 V, 50 Hz, SinglePhase, AC Supply.
12 Film Stripping Device, Film Stripping Device, is used to measure the resistance of bituminous mixtures to stripping of asphalt from aggregate particles. It is generally used to evaluate mineral aggregates & to judge the adhesion of the bituminous materials. The device consists of a disk on which 4 bottles are mounted. The disc rotates at a speed of approx. 100 rpm. The sample, usually the aggregate fraction which passes a 9.525 mm sieve but is retained on a No. 8 sieve, is placed in the bottles & agitated for 15 minutes. The percentage of aggregate stripped can be visually estimated. The device is provided with a pre set
59,000.00
13 Mastic Asphalt Tester Mastic Asphalt Tester as per IS:1195 90,050.00
14 Sieves Sieves Set 20cm diaSeives 4,75 mm2.36 ,2.00,1.80 mm,1.70 mm,1.00mm,212micron,150 micron,600micron,425 micron, 250 micron,125 micron,63micron,90mic, 75 mic and pan and cover.
20,000
Rs. 220670.00
Soil Machines Lab
15 Hand Operated Extractor
Hand Operated Extractor 38mm mm dia specimen, for 38 mm dia specimens for extracting soil core specimens of 38 mm diafromsampling tube or from larger size samplers. It can be usedin the field also, for taking out samples. Having Sample Extractor Frame Screw Type with a Wire Sample Trimmer Jarring Link for driving the Sampling Tube, Adapter with locking screw for fitting the 38 mm diaSampling,Tube to Jarring Link, Split Mould38 mm dia x 76 mm long, provided with Quick Release Clamps. It can be fitted to Sample Extractor, Sampling Tube,Unrelieved, 38 mm dia x 200 mm long 1 No.
12,000.00
16 Sample ject This Extractor has been specially designed to overcome the difficulties faced in extracting specimens from longer Sampling tubes.
Salient Features:
1,50,000.00
High efficiency hydraulic pump.Power pack with quick release couplings.Manual operation possible on power failure.Ejects soil from sampling tubes and moulds upto 60 cm in length and 38 to 150 mm in diameter by a single operation• Allows direct transfer of soil from field sampling tubes, Proctor and CBR moulds into 38 mm diameter tubes with minimal disturbance.• 60 cm piston stroke.• 50kN pushing force.• Electrical-cum-hand operated or only hand operated hydraulic system.• Built-in safety valve to prevent loading beyond 50kN.• Portable, with facility for floor mounting.• Lever for selecting up/down movement of piston.• Top-plate for holding upto 6 sampling tubes of 38 mm dia.
The equipment consist of the following:
1. Adapter rings/Disk kit - Adapter rings and ejector discs for 38, 50, 75, 100 & 150 mm dia sampling tubes or moulds, included.
2. Sampling Tube, Unrelieved,38 mm dia x 200 mm long
17 Infra-Red Moisture Meter
This moisture meter has been designed for rapid and accurate determination of the moisture content of a wide variety of materials. It is torsion wire instruments, the torque being applied to one end of the wire be means of a calibrated drum to balance the loss of weight as the test sample dries under infrared radiation. The speed of drying (about 30min) thus obtained, combined with the frictionless balancing system gives the result as accurate as those obtained by standard oven drying method. Since drying weighing are simultaneously it is useful especially for determination of moisture in substances that quickly reabsorbs moisture after drying. The infrared radiation is controlled by a voltage regulator and thereby provide excellent heat control. The instrument is provided with as indicator lamp. Which glows when the unit is switched on. The torsion balance has a built-in magnetic damper of reduce pan vibration that enables quick weighing. The balance scale (drum) is divided in terms of moisture percentage on wet weight basis, which are read directly from it. Graduations are from 0 to 100% in 0.2 divisions. But readings may be estimated to 0.1% moisture content. Suitable for operation on 220V n50hz single phases AC supply. Capacity: 5g approx... Sensitivity 10mg approx... Range 0 to 100% moisture content on wet weight basis. Reading accuracy: +- 0.20% Probable error : +- 0.25 in the lower upto compared to 25% and +- 1% for
22,510.00
moisture contents oven methods : above 50%
18 Hydrometer Range Hydrometer, Range : 0.995 to 1 540.00
19 High Speed Stirrer Designed as a compact bench-mounted laboratory stirrer for the pretreatment stage of soils before particle size analysis. The mixer spindle operates within a dispersion cup which can be fitted with an ant splashing baffle to improve the efficiency of mixing. Suitable for operation on 220V 50Hz, single phase AC Supply.
25,050.00
Rs. 210100.00Fluid Mechanics Lab
20 Reynolds Apparatus Dye vessel: Material stainless steel suitable capacity, Tube material borosilicate glass. Constant head water tank capacity 40ltrs. Water circulation: FHP pump. Flow measurement: using measuring cylinder. Sump tank: capacity 60ltrs. Stop watch: electronic. Control panel comprises of standard make on/off switch, main indicator etc. tank is be made of stainless steel.
50,740.00
21 Multipurpose Tilting flume
Pre-fabricated Perspex walled multipurpose tilting flume with following dimensions: length = 6m, width= 0.2m and depth 2m
1,99,000.00
22 Metacentric Height Apparatus
Pontoon: size 300x150mm (approx) with a Horizontal guide bar for aliding weight. Water tank: size 600x400x400mm (approx). Front window of tank: made of glass/perspex. A set of weight is supplied with the apparatus. Tank is made of stainless steel.
40,000
Rs. 289740.00Soil Dynamics Laboratory
23 Block Vibration test setup
Consisting of :
1. Mechanical oscillator with eccentricity Indicator and speed sensor specification : peak Force : 2000 kgf at 45 hz Eccentricity : 0-140 deg. CFrequency Range : 0 to 50 HzStandard IS 5249 : 1992
01 610000 610000
2. Variable speed 5HP D.C Motor specifications : Capacity : 5 H.P. or suitable to drive the mechanical oscillator quoted above for the required frequency range at full loadType : Shunt Motor (220V DC)Coupling Arrangement : ProvidedSelf-Vibration : negligible
3. Speed control unit thyristorised Controlled variable speed drive system with digital LED Display to Drive the DC
Motor Specifications: Speed variation : 50 to 3000rpmLeast count : 1 rpmMad drop in voltage at full load : less than 2%Power source 230 + 10 % 50 Hz AC mains Model : MsCu -1000 Accessories fixing plates, Nuts & Bolts, Belt/Flexible shaft, cables and tools etc. to fix the system for operation.
4. Digital vibration meter specification : Display : 312
Digit
LED Resolution : Acc : 0.1g Disp. : 0.01mm Output : Analog output provided
5. Accelerometer Specification: Accelerometer Range : +-5 g
24 Ultra sonic pulse velocity test equipment
Ultra sonic pulse velocity test equipment, complete with lough polyester carrying Bag. Two transducers (54KHz) Ultrasound couplant. Two 3.6 metre cables power supply and manual 100/240V AC 50/60 Hz complete with free computer interface Kit with reference bar.
01 395000 395000
Optional extra
a) Note. For greater depth. 24KHz transducers are required UTR24kHz. Transducer received 50mm dia X 112mm loag.
b) Note. For shallow depth. 150 kHz, transducers are required UTR 150 kHz 150 kHz, transducer receiver 25mm dia X 34 long. If using with them WAD/3.6 BNO-BNC cable is needed.
01
01
130000
110000
130000
110000
Rs. 1245000.00Fluid Machinery Lab
25
26
2728
1. Centrifugal Pump with 10HP motor kirloskar make fatted with all necerary accessories and attachment such as manometer, officemate and pressure gangeupto 100 gange pressure.
2. Reciprocating pump with 10HP motor kirloskar make fitted with all neccrsary accessories and attachment such as manometer, officemate and pressure gangeupto 500 gange pressure.
3. Manometer set for Francis turbure to measure upto 500 pice
4. Digital tachometer with the range 0 to 5000 rpm
01
01
0101
2,00,000
2,00,000
10,0004300
2,00,000
2,00,000
10,0004,300
Rs. Total 3876669.00
(Rupees thirty eight lakhs seventy six thousand six hundred sixty nine) only.
Sl. Name of Equipment
Total Price (Rs.)No. Specification1
Rebound1,50,000.00
: Measuring Range: 10 - 70 N/mm2 (1'450 to
Hammer 10'152 psi). The following standards can beapplied to the Original Schmidt:
ISO/DIS 8045EN 12504-2ENV 206DIN 1048 part 2BS 1881 part 202ASTM C 80SASTM D 5873(Rock)NFP 18-417B 15-225JGJ(r 23-2001)JG 817-1993
System Features:
• Type N Original Schmidt: Rebound valuesare read from a scale for subsequentCalculation of the mean. Compressivestrength values can be read from aconversion diagram
• Type NR Original Schmidt: Rebound valuesare recorded as a bar chart on a paper stripwhich has a capacity for 4'000 test impacts
• Type L Original Schmidt: Handling equalstype NR but the type L offers an Impactenergy three times srnelle.
• Type LR Original Schmidt: Handling equalstype NR, but with impact energy three timessmaller. The LR also features a paper stripfor recording up to 4'000 test impactswithout reloading
StandardizationThe following standards can be aoolied to theOriginal Schmidt:
• ISO/DIS 8045 • ASTM 0• EN 12 504-2 5873(Rock)
• ENV 206 • NFP 18-417
• DIN 1048 part 2 • B 15-225• BS 1881 part 202 • JGJ/T 23-2001• ASTM C 805 • JJG 817-1993System Technical Spedfication:
Original ScmidtType N
Measuring 10 - 70 N/mm2 (1'450 to 10'152 psi)range
Impact 2.207 Nm
energy .
Make: Proceu Asia Pte Ltd
2 PUNDIT LAB 5,25,000.00Consisting of:Display unit, 2 transducers (54 kHZ), 2 BNCcablesl.5 m (5ft), couplant, calibration rod,USB charger with USB-cable, 4xAA(LR6}batteries, data carrier with software,documentation and carrying case.System Features
• Integrated waveform display
• Remote control: A USB connection and thePundit Link application allow full remotecontrol of all features of the ultrasonic testequipment Pundit Lab.
• Open interface: full remote control of theinstrument is also possible with third partysoftware
• Direct data logging on the PC• Multiple Power Supply Options: the
ultrasonic test equipment Pundit Lab runson battery supply, mains supply via ACadaptor and can also be powered from a PCvia the USB connection.
• Wide range of transducers: The ultrasonic
. test equipment Pundit Lab supports a wide
. range of transducers from 24 kHz. up to 500kHz., making it suitable not only for concreteand rock, but also for other materials suchas graphite, ceramics, woods, etc.Exponential transducers for rough surfacesand shear wave transducers for estimationof dynamic modulus of elasticity completethe portfolio.
System Technical dataTransit time measurement of the ultrasonic test
cableMechanical .Dimensions 172 x 5S x 220 rnmWeight 1.316 g (incl. battenes)
Environmental conditions For the ultrasonic testequipmentOperating -100 to 60°C (0° to 1400F)temperatureHumidity <95% RH, non condensingThe ultrasonic test equipment Pundit Lab complieswith the following standards:• EN12504-4 (Europe)
I • ASTM C 597-02 (North America)• BS 1881 Part 203 (UK)• 1501920-7:2004 (International)
• IS13311 (India)
• CECS21 (China)
Software Features :The Windows based software Pundit Link, developedby Proceq, unlocks the full capabilities of theultrasonic test equipment Pundit Lab, providing theuser with:
.' waveform Visualization and analysis turnsyour PC into an oscilloscope.
, • interactive adjustment of trigger point. • on-line data acquisition
• full remote control of the instrumentincluding programmable data loggngfunctionality
• export of data to third party applications
3 I Rebar Locator PROFOMETER 5+ Model 10,50,000.00SCANLOG Basic UnitKey features are identical to Model 5, withadditional key features:'" "Cyber Scan" functions for displaying. thereinforcement.'" "t-1easuring with grid" function for grey-scale display of concrete cover. The objects ofboth functions can be stored, printed outdirectly and transferred to a PC.
Each Basic Unit is identical to Model S withadditional items:• 1 Nos. probe carriage Scan Car with pathmeasuring device and path measuring devicecable 1.55 m f.or scanning,• 1 Nos. Interface converter to printer withparallel Interface, with 2.0 rn cable.Features
• The Profometer 5+ cover meter allows thedetection of rebars
• Correction functens for the Influence ofneighbouring bars
• The cover met r offers optical as well as ,
acoustic locating aids
• Storage of 40'OCO indivrduel cover valuesand statistical analysis (160'000 with modelScanlog)
• Data transfer function from the cover meterto a PC and evluation using the Pro VistaAnalysIs Software, Included with the covermeter,
Applications
• Locate rebars With the cover meter to avoidthem when drilling holes
• Acceptance inspection of cover afterformwork is removed
• Measuring concrete cover depth with thecover meter
• Quality assurance in mass production ofprefabricated concrete elements
• Profometer 5' rover meter Model Scanlog Isespecially suited for large areas and whencomprehensive reporting is required
System Technical Data:non-volatile memory for 40'000
Memory measured values 160'000) and 60objects respectively
.. Display LCD with bac light, 128 x 128 pixelI t fa RS 232 or with adapter for USB Port on
n erce PCS ft Pro Vista for downloading data and
o ware evaluation on PCBattrI six 1.5 V for 45 h operation; 30 h with
e es backlight onMeasuring Range of the cover meterOperating temperature -0 °C to +60 °c
Storage temperature -10°C to +60 -c
Cover depth small range up to 100 mm
measurements (3.94 in.)large range up to 185 mm(7,28 m.)
. up to a cover of 70 mmDiameter measurement (2.76 in.)
StandardizationThe following standards n be applied to the cover
meter:• BS 1881 • SN 505262
part 204 • DGZfP B2• DIN 1045 (recommendation)
Including 390 00 270 Test block4 Canin+ instrument with Device cantn, carrying5,50,000.00
strap, transfer cable, USB adapter. operatinginstruction, rod electrode, caninprovista software.Measuring Range: 0 to 99kncmResolution: lKOcm
ELECTRICAL ENGINEERING DEPARTMENT(C)
Sr No. Name Of Machine Technical Specification DEMAND Rate Amount Remarks
1 Computer System
Intel Processor core i3 or i7 or latest with mother board Intel Chipset 41/61 latest with
4 USB,1 Serial port, 1 LPT port, 2 GB RAM DDR III,500 GB SATA Hard Disk,18"LCD/LED Monitor,Desktop Cabinet with SMPS , DVD writer.Keyboard,USB Mouse,1 GB Network card or latest configuration with microsoft
windows pre loaded
25 pcs
2 UPS 10 KVA Online,6 Hrs Backup with battery 02 pcs
3 Three phase Auto Transformer
15 KVA,Input 415 V,3 phase,50 Hz,Output0-415V,30 A per line,Cooling Air natural 10 pcs
4 Single phase Auto Transformer(Dimmerstat)
Single phase,AirCooled,enclosed model Input:0-230 Volts,10 A Output 0-270 Volts 10 pcs
5 Wattmeter
Portable Type, Accuracy Class-1,
140 mm long Mirror scale Range: 2.5/5A 300V
LPF Type,P.F=0.2
10 pcs
6 Rehostats
Wire wound resistors,Variable,Three terminals. With steel clamp+Brush type
Name Of Equipment Technical Specification DEMAND Rate Amount Remarks
1 Split Type Air Conditioner
1.5 T with suitable stabilizer 5 star rating with installation,make:Samsung/Voltas/LG/Haier 03 pcs 50,000 1,50,000
2 Photo Copier Machine
copy,print, color scan speed 25 ppm A3 size,256 MB RAM,Duplex, Make xerox/ricoh/canon 01 pcs 1,40,000 1,40,000
3 HP color Laser Jet printer Model M252 DW 01 pcs 37,000 37,000
4 Printer laser jet HP laser Jet 1160 or equivalent 02 pcs5 LCD Projector 4.43/PAL/SECAM, with PC interface and audio interface 01 pcs6 Printer Cartridge Mak HP laser Jet P1606dn 06 pcs 5,400 32,4007 Inverter with UPS 1000 VA Make Sukam/Lumionous/Exide/Microtech 03 nos 6000 18,0008 Tubular Battery 12V 180 AH Make:Exide/Sukam/Luminous/ 04 nos 16000 64,0009 Ceiling Fan 1400 mm Make:Havells/USHA/Polar/Crompton 12 nos 2500 30,000
10 Double Tube light set Make:Philips/Havells 15 nos 1000 15,000
11 Water purifier RO-UV-UF Capacity 7-8 ltsMake:Kent/AquaGuard/Hind Lever 1 nos 20,000 20,000
16 MCB 32 A Make:Havells/Anchor 03 pcs17 PVC Tape Make Steel Grip/Anchor Blue Black 10 pcs 10 100
18 Electrical Tool kit setConsisting of Combination plier,Long Nose plier,Cutter, Nose
Plier,Round Nose Plier,Screw driver set,Philips Screw driver,Rawlplug,poker,plumbbob,hammers,Haksawetc
04 pcs
19 soldering Iron Set 25 watt with solder wire, flux,Makesolderon 04 pcs 150 60020 Hydrometer 02 pcs 100 20021 Electric bulb 100w Make:Philips/Bajaj/Surya 50 Pcs 15 75022 Fire Extinguisher Specially for Electrical fire 04 pcs
Sr No.
Name Of Appratus Technical Specification DEMAND Rate Amount Remarks
1 Function generator1 MHz
20 MHz 100 MHz
02 pcs each
2 Solarbotics L 298 H-Bridge board with appropriate connectors 02 pcs each
3 PIC kit 2 with appropriate connectors and driver 02 pcs each
4 RS-232 cable compatible with PCs serial port and dsPIC board's serial port connector i.e DB-9 connector 02 pcs each
5 Power supply ±15 V,3A 02 pcs each
6Bread Board
Development system
Bread board system with DC power O/P 5 V,± 12 V and 0-5V variable,digitalvoltmeter,Ammeter,LED indicators 8 nos,Logic
input switches 08 nos,7-segment display 2 nos,clock generator Manual pulser,Potentiometer, Relay etc with about 1600 bread
board points with suitable digital IC's for logic gates,flipflop,shiftregisters,countersetc
25 pcs
7 Trainer Kit for Digital IC's
Trainer kit shall consist of digital Ics for logic gates,FlipFlop,shiftregisters,counter along with toggle switches
for input and bi-color LED at outputs,built in power supply25 pcs
8 Microprocessor kit 8085
With Logic Interface cards of 8085 microprecessor kit with appropriate connectors 20 pcs
9 Dual DAC card for 8085 10 pcs
10 PIC micro-contrroller Model:PIC 16F877A with appropriate software and connectors 05 pcs
11 Power Factor Meter Single Phase 5-10 A,250 V 05 pcs
12Microcontroller
trainer kit (IC-8051 based)
Intel 89C51 operating at 12 MHz Onboard crystal 12MHz for oscillator 1 & 1.8432 MHz for oscillator 2 Onboard GM16C550 for Asynchronous serial communication 32 KB onboard user
program memory 12 KB battery Backed up user program memory
16KB battery Backed up user data memory 40 Characters X2 lines LCD display controlled by 89C2051 supports esxternal
ASCII keyboard Onboard +5V,+12 V,-12V Dc for peripheral card. Timer counter chip(8253),two counters available for users. Two 8255 chips,giving 48 TTL I/O lines.all signal s terminated on two
26 pin FRc connectors. port P1 pins brought out on 10 pin connectors for user interface. Serial port RS-232 compatible usin
8250,sinals terminated on a 9-pin D-connector. Address ,Data and control bus available on 50 pin FRc connector for expansion.
supports follwing modes of operations: (i)Interrogation mode :for interactive dialog with system (ii) assembler mode:line assembler inbuilt in monitor(iii) single step
mode:useful for single stepping,inserting/removing breakpoints and debugging.powerful monitor software with standard
commands like MOVE,FILL,DISPLAY/MODIFY REGISTERS,EXECUTE PROGRAM,UPLOAD/DOWNLOAD etc.Single
line assemblers/dis-assembler.Software LCD outinesinEPROM:Clearscreen,Row Column, Display
Character,ReadColumn,ReadRow,Display a Message,Cursoroff,CursorOn,Read Keyboard&Display,Read
Suitable simulation software to perform micro controller system programming 10 user licensce copy or open
source software1no
12 C Compiler suitable for micro controller programming 10 user licensce copy or open source software 1no
Sr No. Name Of Furnitures Technical Specification Deman
dRate
Amount
Remarks
1 Wooden Arm Chair with Cushion 15 pcs 5000 75000
2 Computer Table Make: Zuari /Godrej 25 Pcs
3 Computer Chair Make: Zuari /Godrej 25 pcs
ELECTRONICS & COMMUNICATION ENGINEERING DEPTT.
(D)
Total
632000.00
Basic Instruments,Devices&Ics for all Labs of ECE Dept.
S.N. ITEMS WITH SPECIFICATION UNITPRICE (Rs)(Approx)
QTY AMOUNT(Rs)
1. Digital Multimeter 3.5 digit Metravi 702 1700.00 50 85000.002. General Purpose Power Supply:0-150 VD.C., 10 Amp
(variable)DC Output
15000.00 5 75000.00
3. Universal Electronic Trainer kit with 4(four) Bread Board; Power Supply :analog (AC& DC)constant &varriable and Digital 8 bit Input ; display: Digital 8 bit Input & output
15000.00 16 240000.00
4. Universal IC Tester NB 9350 26000.00 01 26000.00
5. 10 MHz Function GeneratorFrequency Range:0.5Hz to 10MHz;Resolution:10MHz;Waveforms;Sine,Square;Traingle,Ram,Pulse;DC Offset; AM/FM; 40MHz Auto Ranging Frequency Counter.
S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx) QTY AMOUNT
1. Bench LCR MeterSpecification: Five-terminal measuring technology;It can measure - inductance (L)Capacitance(C), resistance (R), quality factor(Q) and dissipation factor (D).With a basicAccuracy of 0.25% and five digit displayResolution
45,000.00 01 45,000.00
2. Single Phase Watt Meter 3200.00 01 3200.003. Maxwell's Bridge Trainer Kit 6000.00 02 12000.00
11. Frequency meter Training Kit 11000.00 02 22000.00
12. Schering Bride Aquile/Lale Make with built in 8000.00 02 16000.00
regulated
Power supply 230v,AC
13. Measurement of temperature with Thermister 6000.00 02 12000.00
14. Linear variable differential transducer (L.V.D.T) 4500.00 02 9000.00
15. Optical transducer trainer Omega type ICT-904 5500.00 02 11000.00
16. CRO Trainer Board having block tracing facility with
various test points
25,000.00 02 50,000.00
Total 2,76,200.00
Digital Signal Processing LabECE
S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx)
QTY AMOUNT
1. DSP Lab Version 2Features:Based on TMS320C6713 processor.Sampling & Waveform GenerationQuantizationPCM EncodingDelta ModulationDigital Modulation Schemes (ASK, PSK, FSK)Error Correcting CodesRead Write from CODECFast Fourier TransformFIR Filter implementation (Low P ass, High Pass, BandStop)IIR Filter implementationLinear ConvolutionAuto CorrelationPower Spectral DensityPlay Sound, Echo, Echo with FadingMultiple Echo, ReverberationSound MixingOn board Switch and LED InterDSK 6713-MATLAB Interface facing Program with DSK 6713
55,000.00 02 110000.00
2. DSP Development PlatformFeatures:External 5 V DC power supplyIEEE 1284 compliant male-to-female cableCode Composer Studio DSK toolsStudy and Analysis of FIR FilterLow Pass, High Pass, Band Pass, Band Stop filterStudy and Analysis of IIR FilterButterworth Approximation, Chebychev ApproximationStudy and Analysis of Adaptive FiltersLMS Algorithm, Noise CancellationStudy and Analysis of Digital Modulations TechniqueQAM, BPASK, PSK, FSKInterface MATLAB (Simulink )with 6713Read-Write using Simulink-6713Smart Tech-Book model.Smart E-manual for easy understanding.
70000.00 02 140000.00
3. DSP Development Board.Features:High performance 32 bit, TMS320F2812 Digital SignalController32 x 32 bit or dual 16 x 16 bit MAC8-stage fully protected pipelineFast interrupt response manager128Kw on-chip flash memoryCode Security Module (CSM)Two event managers56 shared GPIO pinsWatchdog timerCommunications peripherals12 channel PWM12 bit 16 channel ADC moduleInterfacing with Stepper Motor, Servo Motor, DCmotor.Interfacing with Character LCD and Graphic LCD.Interfacing with Temperature sensor and relay.Interfacing with DIP Switch and LED.Smart Tech-book Model.Smart Manual for easy understanding.DSP Technology learning software.
80000.00 02 160000.00
Total 410000.00
Microprocessor LabECE
S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx)
QTY AMOUNT
1. 8051 Microcontroler Training Kit with in-built P.S. 12000.00 03 36000.00
2. 8085Micro processor Training Kit within built Power
Supply ;opcode input facility.
20000.00 05 100000.00
3. 8251 Serial Data Interface card 2600.00 03 7800.00
4. ADC Peripheral interface study Card 2600.00 03 7800.00
5. DAC Peripheral interface study Card 2500.00 02 5000.00
6. Temprature Control interface card 7000.00 02 14000.00
8. Stepper Motor control Interface Card 3500.00 02 7000.00
9. DC motor speed controller Interface Kitek IC – 14 7000.00 02 14000.00
Total 205600.00
. Electronics Software LabECE
S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx)
QTY AMOUNT
1. Micro Tutor DSP Embedded lab▪ All in one DSP educational practice Boardwith code composer Studio for DSP …………..… 5 No.▪USB TAG Simulator………………….. 5 No.▪ Color CCD Camera…………………. 1No.▪ Interactive work book …………….... 1 No.▪ Application specific kits for DSP …… 4 No.
---
Total
Set
3,50,000.00
2. Lab View -measurement and instrumentation software latest version license for 5 PC
- - 3,00,000.00
3. Turbo C 2,500.00 01 2,500.00
4. M.S. Office 2007 11,000.00 10 1,10,000.00
5. Visual basic 6.0 11,000.00 01 11,000.00
6. Multi Sim latest version license for 25 PC - - 5,75,000.00
7. Vis Sim-com Software latest version license for 10PC - - 4,85,000.00
8. MATLAB Software Latest VERSION license for 20 PC
- - 3,00,000.00
9. Multimedia Projector1.Multimedia Projector Resolution: 1024 x 768 x GA, Lumens 30002.15 Meter VGA Cable3.Laser Pointer
55000 01 55,000.00
Total 21,38,500.00
S.N. ITEMS WITH SPECIFICATION UNITPRICE(Approx)
QTY AMOUNT
1. Godrej Bench Desk ( Seat, front & back – wooden) 18000.00 100 1800000.00
10 AC withStablizer for Language Lab, required AC 04 no. with Stablizer. 50,000 x 4 200000
11 False Ceiling with Strong Arm, Gypsum Board, complete finishing 3,50 x 1000 350000
12 Ceiling Light 2/2 Feet make Bajaj, Philips, Havells. 10,500 x 10 105000
13 Blind / Parda as per Requirment. 6 x 8 160 x 48 7,680
TOTAL = 3511480
(H)SMART CLASS LAB FOR 60 NOS. OF STUDENTS
S.No. Particulars Rate Qty. Amount1 Chair with Writing Pad 6, 500 x 60 390000
2PVC Flooring 1.5mm thickness Supply &Pasting ( for Area of 1,500 to 2,000 Sqft.)
100 x 2000 200000
3AC withStablizer for Language Lab for 1,500 to 2000 Sqft Area, required AC 04 no. with Stablizer.
50,000 x 4 200000
4 False Ceiling with Strong Arm, Gypsum Board, complete finishing3,50 x 2,000 Sqft. 700000
5 Projector for Smart Classes with Remote 1, 00, 000 x01 1000006 Digital Sound System for Smart Classes With Mike Set. 1, 25, 000 x 01 1250007 Smart white interactive Board for Smart Classes of diagonal 78" 1, 20, 000 x 01 120000
Three (03) Smart classes are proposed Grand Total =1905000 X 03 =
5715000
ANNEXURE 2Digital library
The system is structured to expose students to multifarious learning experience and opportunities that challenges and maximizes their learning
potential. Providing education digitally and making it available to everyone every where is the main function of Digital Library. The teachers get the
relevant digital resources such as animations and videos, interactive virtual labs tools etc. and use them as a part of their lesson plans in every
classroom period. Learners can use the digital library to view content at their own choice post class hours. The basic aim is to provide a complete
system with easy to use interface which will manage all videos, reference document, resources, digital content to centralize all the learning recourses of
the academy and provide end users a unified platform for viewing. It is Propriety Item. The price of Digital Library (Online): E Repository7 + 2500
Training Need Analysis/ Software Requirements for Students and Teachers of BCE Bhagalpur
S.N. Departments Subject Related Training and Software
7 • Enroll - Provide login id and password to your students and teachers and enroll them.• Study plan - Create a path of his/her own learning• Follow - Follow any teacher, course, channel to be updated about their latest advancements• Personalized Digital Library – Create your personalized digital content library.• Integration – This solution provides integration with the Digital lecture studios in thecampus, Campus Management System and the Campus Wide Networking.• Increase star rating - Favouratise or like a lecture, teacher or course and increase its starrating.• Comment - Post comments and seek others comments and viewpoints
1. Mechanical CAD/ CAM Software ( Computer added Design and computer added Manufacturing ) Software for Mechanical EngineeringFinite Element Analysis Software for Stress Analysis , Mechanical vibration, Fatigue Motion, Heat transfer, fluid flow, electrostaticsSoftware for Machine Design: - Solid Edge (Complete Hybrid 2D/3D CAD system for accelerated Design, faster change.Project Planning software in Mechanical EngineeringPro/ Engineer Software for DesignSAP ( System, Application & Product) SoftwareERP ( Enterprise Resources Planning) SoftwareMechatronics software for Machine Design and RoboticsBig Data Analytics softwareSoftware for Automotive Design and manufacturing process with Design simulation softwareSoftware for basic of Robotics System and its DesignCATIA Software ( Computer added 3 Dimensional interactive application)Programming: C++Cloud Computing SoftwareMATLAB Software
2. Civil Auto CAD for Civil EngineeringS TAAD Pro for structural Analysis and Design of StructureProgramming: C++MATLAB softwareFinite Element Analysis Software for Stress Analysis , Mechanical vibration, FatigueETABS for Building Analysis and Design softwareSAP 2000 for dynamic AnalysisPrimavera Project Planner software for Construction ManagementCSI SAFE software designing Concrete floor and foundation SystemMXRoads software for designing all types of RoadsCloud Computing SoftwareVisual basic software for generation of graphicsGIS software solution for civil EngineeringCloud Computing Software
3. Electrical ETAB software for Design , power Management, Substation
Automation , Load shedding etc.Auto CAD for Electrical DesignELECDES for Electrical DesignSmartDraw software for designing electronic circuit, Automotive wiring, Circuit Schematics and designing digital circuits.Programming: C++MATLAB softwareSoftware for Estimating Electrical ProjectsEasyPower software for short circuit calculationsCloud Computing Software
Training requirements
Power System DesigningTransformer DesigningControl System DesignEmbedded system Design
4 Electronics and Communication ECAD : VLSI Design Software
Programming: C++Advanced JavaMATLAB softwareXilinx ISE for analysis of HDL DesignsCloud Computing SoftwareVIDE software for designing , testing and debugging Verilog applVHDL softwareIE3D, Antenna softwareFPGA KitXUP VirTEX OPEN SPARC BOARDIAR Embedded workbench Mcos/os II and II
Training requirements Web Development
Printed Circuit Board (PCB) DesigningPLC ( Programming Logic Control)Power System DesigningControl System DesignEmbedded system DesignEthical Hacking & Cyber SecurityMicrocontroller & MicroprocessorsAutonomous Robotics, 6th sense Robotics
5 Computer Science And Engineering Programming: C++
Web DesigningDesign and Analysis of AlgorithmsComputer Languages like C++,Java, Linux,Development of computer and hardware systemFoundation of Software EngineeringAndroid Application DevelopmentEthical HackingCyber SecurityCloud Computing
Common Training Need Analysis Requirements for Students, supporting staff and Teachers of BCE Bhagalpur
1. Soft Skill Development: Soft skills revolve around personal relationships, character, and attitude. By developing these skills, students may increase their performance, build stronger relationships, and work toward achieving objectives of life.
2. Training for doing experiments through virtual Lab
3. Communication skills
4. Personality Development: Taking Control of our Life with the Science of Personal Development.
5. Training of Fundamental Science for weak students
6. Basic Computer skills for faculty, staff and students
Training Need Analysis Requirements for supporting staff &Teachers of BCE Bhagalpur
(C)
Lesson planning
Improving Teaching Skill (Including Micro Teaching Sessions)Effective Teaching Methods and ICT enabled learningMotivating Student for LearningLaboratory/Workshop Instruction DesignStudent Performance EvaluationDesigning Questions (Development of Question Bank)Student Counselling & Career GuidanceApplication of Computer/IT in educationEducational PsychologyInstructional material developmentClassroom ManagementWriting research proposalsTraining psychologyUndertaking systemic researchOrientation/Refresher/Induction PorgramsCurriculum Development & Implementation relatedDevelopment of competency based curriculum in technical coursesDesign of question bank for effective implementation of currculumInnovative approaches in curriclum designManagement/Institutional Management/Communication relatedTQM in Institutional ManagementInstitutional DevelopmentDevelopment of Quality management system (QMS)/ ISO 9001:2008 in technical institutionsProject Planning & Management for teachersDeveloping Interpersonal Relationship in OrganizationsMaking effective presentationHuman resource development & managementPersonality DevelopmentImproving Communication/soft skill in day to day transactionsEnvironmental Awareness/Education/management including ISO 14001 2004 for teachersProcess of Accreditation in technical educationPlanning & implementing staff training program in institutionsManagement for general office staffOrganized problem solving & decision makingManagement principles for technical teachers
Development and use of Instructional mediaTeam Building & team performanceTeachers role in entrepreneurship development among students
Note: Expenditure for procurement of any equipment and furniture will not be admissible if procured with Government of Bihar Supports or any other
sources.
Expenditure for any Civil Work activity will not be admissible if undertaken with other sources.
Additional operating cost if required will be borne by the Department of Science and Technology.
The above activities are only indicatives
Procurement and Foreign Visits will be approved by SPFU and NPIU.
For all other activities Institutes should have full freedom to execute the action.