7Ç1 'Ӵ È1 %,ӊ1 3+È3 7+, &Ð1* &+Ӕ1* 7+Ҩ0 WATERPROOFING METHOD STATEMENT ....., 2020 'Ӵ È1 PROJECT R00 &Ð1* 7< 71++ 9Ӳ$ È &+Æ8 $6,$ 0257$5 Co., LTD
CONTENTS
METHOD STATEMENT
1. BASEMENT SLAB 2
+ )
2. D. WALL
+ )
3. : LIFT PIT
+ )
4. : WATER TANK
TREATMENT TANK, SEPTIC TANK
+ )
SWIMMING POOL
TOILET, BALCONY, WET AREA
R.C ROOF, TERRACE, GUITTER
+ PRODUCT (Method 1):
+ PRODUCT (Method 2): VISCOGUM SAND
9. R.C ROOF,
+ PRODUCT (Method 1):
+ PRODUCT (Method 2): VISCOGUM SLATED
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CONTENTS
10. PODIUM SLAB
+ PRODUCT :
11. PLANTER BOX, LANDSCAPE
+
CONSTRUCTION JOINT
WATERSTOP: FLEXSTOP IC/IX 200/250
FLEXSWELL
TREATMENT FOR TIE-ROD
(AM FLEXSEAL )
PART 1 BASEMENT SLAB 2
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
ng
Lean concrete
R.C Slab
Waterproofing area
ProductRemark
Basement slab 2
AM FLEXSEAL
5.0 kg/m
2
Construction joint
AM FLEXSWELL
DETAIL BDETAIL A
ng
Lean concrete
R.C Slab
WATERPROOFING M.S FOR BASEMENT SLAB 2
D.WALL
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water
Cut off unnecessary steel bars or tie-rods in minimum 30x30 mm depth
to concrete surface
R.C SLAB
AM FLEXSWELL
AM FLEXSWELL SWELLABLE
RUBBER OR BENTONITE STRIP
COMPRESS SOIL
LEAN CONCRETE
AM FLEXSEAL
W.P LAYER: AM FLEXSEAL
NOTE(s):
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
BASEMENT SLAB 2
BASEMENT SLAB 2
BASEMENT SLAB 1
Diaphragm wall
AM FLEXSEAL
W.P layer: AM FLEXSEAL
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
1/2 H
DETAIL A
DETAIL B
AM FLEXSEAL
W.P layer: AM FLEXSEAL
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
AM FLEXSEAL
METHOD STATEMENT-DRY POWDER SPRINKLING AM FLEXSEAL FOR SLAB
SAMPLE PICTURE
SURFACE PREPARATION:
Cleaning the surface and remove all debris.
The surface does not need to be dry but standing water must be removed.
/ MIXING:
No water added into powder.
AM FLEXSEAL
2
Pre-calculate the amount of AM FLEXSEAL required at 5.0 kg/m
2
/ APPLICATION:
AM FLEXSEAL
2
Step 1: Dry sprinkle the powder AM FLEXSEAL (consumption 5.0 kg/m
2
) evenly throughout the area required onto
lean concrete before casting concrete 20 - 30 minutes.
AM FLEXSEAL .
Step 2: In dry conditions concreting conducted over a period of 24 hours after sprinkle AM FLEXSEAL. Construction
temperature from to
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
AM FLEXSEAL
METHOD STATEMENT-DRY POWDER SPRINKLING AM FLEXSEAL FOR SLAB
SAMPLE PICTURE
SURFACE PREPARATION:
Cleaning the surface and remove all debris.
The surface does not need to be dry but standing water must be removed.
/ MIXING:
No water added into powder.
AM FLEXSEAL
2
Pre-calculate the amount of AM FLEXSEAL required at 5.0 kg/m
2
/ APPLICATION:
AM FLEXSEAL
2
Step 1: Dry sprinkle the powder AM FLEXSEAL (consumption 5.0 kg/m
2
) evenly throughout the area required onto
lean concrete before casting concrete 20 - 30 minutes.
AM FLEXSEAL.
Step 2: In dry conditions concreting conducted over a period of 24 hours after sprinkle AM FLEXSEAL.
Construction temperature from to
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
SURFACE PREPARATION
1. sinh lo b c c c n b n a, c b n D ng b
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. must be
removed by high pressure water jetting machine or mechanical method .
AM FLEXSEAL ng ng n c.
The surface does not need to be dry but standing water must be removed.
3. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with latex motar.
ch n ng, khe n n b b ng c ch c
a ng
Repair construction joints, surface cracks by chiping of form V after fill non-shink grout (if any).
Pipe treatment (if any)
Pre-water or damp the surface prior to application
V-Shape hackFill with Grout
Apply Waterproofing layer
MIXING:
1. n c ch o ng c a. Sau b AM FLEXSEAL o ng
c ho c b ng tay n n AM FLEXSEAL c cho n khi nh h
ng n ng b n c c.
Pour water into a pail, and pour AM FLEXSEAL powder slowly into pail and mix with a low speed mixing
machine or with paddle by hand. Mix until a slurry of even consistency is achieved.
Mixing ratio:
5.0- 8.0 n c : 25kg AM FLEXSEAL (
2
).
25kg AM FLEXSEAL : 5.0- 8.0 liters water (Apply at 5.0 kg/m
2
in two coats)
.
Do not add water.
Mixed material should be used within 20 minutes, recommended not more than 30 minutes. The
material can be mixed again if it hardens but do not add water again.
APPLICATION:
1:
Pre-water or damp the surface prior to application.
D ng c thi c ng n AM FLEXSEAL
c o .
Apply the first coat of AM FLEXSEAL by brush onto the surface concrete.
3: Sau kho ng 1-2 thi c ng 2 ng thi c ng 2 sau 24 .
After approximately 1-2 hour, apply the second coat finish recommended not more than 24 hous.
B c 4:
Proceed to maintenance irrigation.
AM FLEXSEAL
METHOD STATEMENT - APPLIED AM FLEXSEAL BY BRUSH
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
PRODUCT(AM FLEXSEAL)
PART 2 D.WALL - BASEMENT SLAB
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR D. WALL - BASEMENT SLAB 2
R.C Slab
B ng
Lean concrete
AM FLEXSTOP XX 250
Waterstop: AM FLEXSTOP XX 250
AM FLEXSEAL
W.P layer: AM FLEXSEAL
TRENCH DETAIL
L AM FLEXSEAL
W.P layer: AM FLEXSEAL
Waterproofing area
ProductRemark
Basement
AM FLEXSEAL
Construction joint
AM FLEXSTOP XX/IC 250
DETAIL A
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to
concrete surface
AM GROUT 307
After installed and filled with grout, penetration pipes cut off closely to
concrete slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
TREATMENT PIPE
INSIDE
D. Wall
Pipe
OUTSIDE
Mesh - Corner reinforcement
W.P layer - Corner reiforcement
DETAIL A
AM FLEXSTOP XX 250
WATERSTOP: AM FLEXSTOP XX 250
NG
LEAN CONCRETE
R.C SLAB
L AM FLEXSEAL (5.0 KG/M
2
)
W.P LAYER: AM FLEXSEAL (5.0 KG/M
2
)
BASEMENT SLAB 1
BASEMENT SLAB 2
BASEMENT SLAB 2
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
AM GROUT 307
Non-shrink Grout AM GROUT 307
METHOD 1
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR D. WALL - BASEMENT SLAB 2
R.C Slab
B ng
Lean concrete
AM FLEXSTOP XX 250
Waterstop: AM FLEXSTOP XX 250
AM FLEXSEAL
W.P layer: AM FLEXSEAL
TRENCH DETAIL
L AM FLEXSEAL
W.P layer: AM FLEXSEAL
Waterproofing area
ProductRemark
Basement
AM FLEXSEAL
Construction joint
AM FLEXSTOP XX/IC 250
DETAIL A
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to
concrete surface
AM GROUT 307
After installed and filled with grout, penetration pipes cut off closely to
concrete slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
TREATMENT PIPE
INSIDE
D. Wall
Pipe
OUTSIDE
Mesh - Corner reinforcement
W.P layer - Corner reiforcement
DETAIL A
AM FLEXSTOP XX 250
WATERSTOP: AM FLEXSTOP XX 250
NG
LEAN CONCRETE
R.C SLAB
L AM FLEXSEAL (5.0 KG/M
2
)
W.P LAYER: AM FLEXSEAL (5.0 KG/M
2
)
BASEMENT SLAB 1
BASEMENT SLAB 2
BASEMENT SLAB 2
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
AM GROUT 307
Non-shrink Grout AM GROUT 307
METHOD 2
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
AM FLEXSEAL
METHOD STATEMENT-DRY POWDER SPRINKLING AM FLEXSEAL FOR SLAB
SAMPLE PICTURE
SURFACE PREPARATION:
Cleaning the surface and remove all debris.
The surface does not need to be dry but standing water must be removed.
/ MIXING:
No water added into powder.
AM FLEXSEAL
2
Pre-calculate the amount of AM FLEXSEAL required at 5.0 kg/m
2
/ APPLICATION:
AM FLEXSEAL
2
Step 1: Dry sprinkle the powder AM FLEXSEAL (consumption 5.0 kg/m
2
) evenly throughout the area required onto
lean concrete before casting concrete 20 - 30 minutes.
AM FLEXSEAL.
Step 2: In dry conditions concreting conducted over a period of 24 hours after sprinkle AM FLEXSEAL. Construction
temperature from to
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
I. CHU N B B M T/ SURFACE PREPARATION
1. V sinh lo i b p ch m t nh h , v t, c ho ng
h c v sinh b m t.
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. must be
removed by high pressure water jetting machine or mechanical method
2. B m AM FLEXSEAL n ph c ng n c
The surface does not need to be dry but standing water must be removed
, t ong ph i i b ng v AM LATEX 302
Repair honey comb concrete by AM LATEX 302 motar.
4. X ty, c t b s t l m t b c l r ng 50x50mm sau ng v a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with latex motar.
5. X ch ng ng, khe n m t b c v ch ng V sau a
Repair construction joints, surface cracks by chiping of form V after fill non-shink grout (if any).
6. X ng (n
Pipe treatment (if any)
7. T o m tr
Pre-water or damp the surface prior to application
V-Shape hackFill with Grout
Apply Waterproofing layer
MIXING:
1. n c ch o ng c a. Sau b AM FLEXSEAL o ng
c ho c b ng tay n n AM FLEXSEAL c cho n khi nh h
ng n ng b n c c.
Pour water into a pail, and pour AM FLEXSEAL powder slowly into pail and mix with a low speed mixing
machine or with paddle by hand. Mix until a slurry of even consistency is achieved.
Mixing ratio:
5.0- 8.0 n c : 25kg AM FLEXSEAL (
2
).
25kg AM FLEXSEAL : 5.0- 8.0 liters water (Apply at 5.0 kg/m
2
in two coats)
.
Do not add water.
Mixed material should be used within 20 minutes, recommended not more than 30 minutes. The
material can be mixed again if it hardens but do not add water again.
APPLICATION:
1:
Pre-water or damp the surface prior to application.
D ng c thi c ng n AM FLEXSEAL c o .
Apply the first coat of AM FLEXSEAL by brush onto the surface concrete.
3: Sau kho ng 1-2 thi c ng 2 ng thi c ng 2 sau 24 .
After approximately 1-2 hour, apply the second coat finish recommended not more than 24 hous.
4:
Proceed to maintenance irrigation.
AM FLEXSEAL
METHOD STATEMENT - APPLIED AM FLEXSEAL BY BRUSH
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
PRODUCT(AM FLEXSEAL)
PART 3 LIFT-PIT
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
LEAN CONCRETE
PILE CAP
WATERPROOFING METHOD STATEMENT FOR LIFT PIT
AM FLEXSWELL
AM FLEXSWELL SWELLABLE RUBBER OR
BENTONITE STRIP.
AM FLEXSEAL
W.P LAYER: AM FLEXSEAL
100
100
DETAIL A
DETAIL B
BASEMENT SLAB 2
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
NOTE(s):
Waterproofing area
Product
Remark
Lift pit
AM FLEXSEAL
5.0 kg/m
2
Construction joint
AM FLEXSWELL
DETAIL BDETAIL A
Pile cap
AM FLEXSEAL
W.P layer: AM FLEXSEAL
100
BASEMENT SLAB 2
c c ng AM FLEXSEAL
W.P layer by sprinkle: AM FLEXSEAL
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
SURFACE PREPARATION.
1. sinh lo b c c c n b n a, c b n D ng b
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc.
must be removed by high pressure water jetting machine or mechanical method.
AM FLEXSEAL ng ng n c
The surface does not need to be dry but standing water must be removed.
3. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the
hole with latex motar.
ch n ng, khe n n b b ng c ch c
a ng
Repair construction joints, surface cracks by chiping of form V after fill non-shink grout (if any).
Pipe treatment (if any)
Pre-water or damp the surface prior to application
V-Shape hackFill with Grout
Apply Waterproofing layer
MIXING:
1. n c ch o ng c a. Sau b AM FLEXSEAL o ng
c ho c b ng tay n n AM FLEXSEAL c cho n khi nh h ng
n ng b n c c.
Pour water into a pail, and pour AM FLEXSEAL powder slowly into pail and mix with a low speed mixing
machine or with paddle by hand. Mix until a slurry of even consistency is achieved.
Mixing ratio:
5.0- 8.0 n c : 25kg AM FLEXSEAL (
2
).
25kg AM FLEXSEAL : 5.0- 8.0 liters water (Apply at 5.0 kg/m
2
in two coats)
.
Do not add water.
Mixed material should be used within 20 minutes, recommended not more than 30 minutes. The material
can be mixed again if it hardens but do not add water again.
APPLICATION:
1:
Pre-water or damp the surface prior to application.
D ng c thi c ng n AM FLEXSEAL c o .
Apply the first coat of AM FLEXSEAL by brush onto the surface concrete.
3: Sau kho ng 1-2 thi c ng 2 ng thi c ng 2 sau 24 .
After approximately 1-2 hour, apply the second coat finish recommended not more than 24 hous.
4:
Proceed to maintenance irrigation.
AM FLEXSEAL
METHOD STATEMENT - APPLIED AM FLEXSEAL BY BRUSH
PART 4 WATER TANK
(AM FLEXPROOF 502)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
DETAIL A
DETAIL B
PROTECTION SCREED
MESH - CORNER REINFORCEMENT
FILLET
DETAIL A DETAIL B
R.C. wall, slab
AM FLEXPOOF 502
W.P layer: AM FLEXPOOF 502
Protection screed
Protection screed
W.P layer - Corner reinforcement
R.C. wall, slab
Fillet
Mesh - Corner reiforcement
AM FLEXPROOF 502
W.P layer: AM Flexproof 502
WATERPROOFING METHOD STATEMENT FOR WATER TANK
Waterproofing area
ProductRemark
Water tank
AM FLEXPROOF 502
2.5 kg/m
2
Construction joint
AM FLEXSTOP IC 200
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete surface
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and poured concrete
again on design requirement
NOTE(S):
AM SEAL PU1
AM SEAL PU1 sealant
R.C wall, slab
W.P layer - Corner reinforcement
AM GROUT 307
Non-shrink Grout AM GROUT 307
PIPE TREATMENT
AM FLEXPOOF 502
W.P layer: AM FLEXPROOF 502
Finishing layer
Mesh - Corner reiforcement
Finishing layer
Protection screed
Finishing layer
FINISHING LAYER
AM FLEXPROOF 502
W.P LAYER - CORNER REINFORCEMENT: AM FLEXPROOF 502
LEAN CONCRETE
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
WATER TANK
AM FLEXSTOP IC 200
WATERSTOP: AM FLEXSTOP IC 200
W.P LAYER: AM FLEXPROOF 502 (3 LAYRERS)
R.C SLAB
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
/ MIXING:
Pour Part A (liquid) into a pail, and pour Part B (powder) slowly into the pail and mix with a low speed mixing
machine or with paddle by hand. Mix until a slurry of even consistency is achieved (apx. 3minutes).
AM FLEXPROOF 502:
METHOD STATEMENT OF AM FLEXPROOF 502:
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. Must be
removed by mechanical method .
Repair chamfered beams, columns before applying waterproofing.
3. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with
latex motar.
ch n ng
Repair construction joints by mesh reinforcement.
Do fillet at corner
Pipe treatment (if any)
Pre-water or damp the surface prior to application
APPLICATION:
Step 1: Apply one coat stick mesh at corner of wall - slab.
2
n, ng c o .
Step 2: Apply first coat (consumption 0.8 kg/m
2
), over the pre-wetted wall, slab.
2
).
Step 3: Apply second coat (consumption 0.8 kg/m
2
) after the first coat has dried (4-5 hours).
2
)
Step 4: Apply third coat (consumption 0.9 kg/m
2
) after the second coat has dried (4-5 hours).
B c 5: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 5: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 6: Screeding/ plastering for protection after fluid test.
Waterproofing layer
Mesh reinforcement
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
WATER TANK
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
PRODUCT(AM EPOXICOTE TAR/ AM EPOXICOTE 402F)
PART 5 TREATMENT TANK, SEPTIC TANK
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR TREATMENT TANK, SEPTIC TANK
Waterproofing area
Product
Remark
Treatment tank, Septic tank
AM EPOXICOTE TAR
0.46 kg/m
2
Construction joint
AM FLEXSTOP IC 250
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
DETAIL B PIPE TREATMENT
R.C. wall, slab
DETAIL A
NOTE(s):
R.C. wall, slab
DETAIL A
DETAIL B
R.C SLAB
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
AM EPOXIPRIMER 401 MT
EPOXY PRIMER: AM EPOXIPRIMER 401 MT
EPOXIPRIMER 401 MT
Epoxy primer: EPOXIPRIMER 401 MT
EPOXICOTE TAR
Epoxy coating: EPOXICOTE TAR
AM EPOXICOTE TAR
EPOXY COATING: AM MEPOXYCOTE TAR
EPOXIPRIMER 401 MT
Epoxy primer: EPOXIPRIMER 401 MT
EPOXICOTE TAR
Epoxy coating: EPOXICOTE TAR
R.C wall, slab
Mesh - Corner reiforcement
EPOXICOTE TAR
W.P layer - Corner reinforcement: EPOXICOTE TAR
EPOXICOTE TAR
Epoxy coating: EPOXICOTE TAR
EPOXIPRIMER 401 MT
Epoxy primer: EPOXIPRIMER 401 MT
AM SEAL PU1
AM SEAL PU1 sealant
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
METHOD 2
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
METHOD STATEMENT:
PREPARATION BEFORE THE CONSTRUCTION:
Check the quality of the concrete before applying waterproofing water test.
SURFACE PREPARATION:
The wall surfaces must be sound . Measuring the substrate moisture.
Wall surfaces must be treated and sandpaper to achieve a fairy surface.
Repair chamfered beams, columns before applying waterproofing.
latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with latex motar.
Repair construction joints by mesh reinforcement..
Do fillet at corner
Pipe treatment (if any)
MIXING:
1. AM EPOXIPRIMER 401 MT:
Stir part A gently, then pour into part B container and mix at least 2 minutes
using electrical mixer with suitable mixing paddle (round speed appx.
500-600 rpm) until a homogenous compound achieved.
2. AM EPOXYCOTE TAR :
Stir part A gently, then pour into part B container and mix at least 2 minutes
using electrical mixer with suitable mixing paddle (round speed appx.
500-600 rpm) until a homogenous compound achieved.
APPLICATION:
AM EPOXIPRIMER 401 MT 0.15 Kg/ m
2
Step 1: Apply AM EPOXIPRIMER 401 MT (consumption 0.15 Kg/ m
2
) onto the treated surfaces.
AM EPOXIPRIMER 401 MT AM
EPOXICOTE TAR
2
)
Step 2: Apply the first AM EPOXICOTE TAR (consumption 0.23 Kg/ m
2
) after AM EPOXIPRIMER 401MT
layer has dried (4-6 hours)
AM EPOXICOTE TAR AM
EPOXICOTE TAR 0.23 Kg/ m2)
Step 3: Apply the second AM EPOXICOTE TAR layer (consumption 0.23 Kg/ m2) after the first AM
EPOXICOTE TAR layer has dried (4-6 hours)
AM EPOXICOTE TAR
Step 4: Protect AM EPOXICOTE TAR layer from damp ,condensation and water at least 2 days after
application, Epoxy system should be ready in use after 7 days.
Step 5: Do fluid test after 7 days, within 48-72 hours .
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR TREATMENT TANK, SEPTIC TANK
Waterproofing area
Product
Remark
Treatment tank, Septic tank
AM EPOXICOTE 402F
0.45 kg/m
2
Construction joint
AM FLEXSTOP IC 250
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
DETAIL B PIPE TREATMENT
R.C. wall, slab
DETAIL A
NOTE(s):
R.C. wall, slab
DETAIL A
DETAIL B
R.C SLAB
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
AM EPOXICOTE 402F
EPOXY PRIMER: AM EPOXICOTE 402F
AM EPOXICOTE 402F
Epoxy primer: AM EPOXICOTE 402F
AM EPOXICOTE 402F
Epoxy coating: AM EPOXICOTE 402F
AM EPOXICOTE 402F
EPOXY COATING: AM MEPOXYCOTE 402F
R.C wall, slab
Mesh - Corner reiforcement
AM EPOXICOTE 402F
W.P layer - Corner reinforcement: AM POXICOTE 402F
AM SEAL PU1
AM SEAL PU1 sealant
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
AM EPOXICOTE 402F
Epoxy primer: AM EPOXICOTE 402F
AM EPOXICOTE 402F
Epoxy coating: AM EPOXICOTE 402F
AM EPOXICOTE 402F
Epoxy primer: AM EPOXICOTE 402F
AM EPOXICOTE 402F
Epoxy coating: AM EPOXICOTE 402F
METHOD 2
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
METHOD STATEMENT:
PREPARATION BEFORE THE CONSTRUCTION:
Check the quality of the concrete before applying waterproofing water test.
SURFACE PREPARATION:
The wall surfaces must be sound . Measuring the substrate moisture.
Wall surfaces must be treated and sandpaper to achieve a fairy surface.
Repair chamfered beams, columns before applying waterproofing.
latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with latex motar.
Repair construction joints by mesh reinforcement..
Do fillet at corner
Pipe treatment (if any)
MIXING:
1. AM EPOXICOTE 402F
Stir part A gently, then pour into part B container and mix at least 2 minutes
using electrical mixer with suitable mixing paddle (round speed appx.
500-600 rpm) until a homogenous compound achieved.
APPLICATION:
AM EPOXICOTE 402F 0.15 Kg/ m
2
Step 1: Apply AM EPOXICOTE 402F (consumption 0.15 Kg/ m
2
) onto the treated surfaces.
AM EPOXICOTE 402F AM EPOXICOTE
402F
2
)
Step 2: Apply the first AM EPOXICOTE 402F (consumption 0.15 Kg/ m
2
) after AM EPOXICOTE 402F
layer has dried (4-6 hours)
AM EPOXICOTE 402F AM
EPOXICOTE 402F 0.15 Kg/ m2)
Step 3: Apply the second AM EPOXICOTE 402F layer (consumption 0.15 Kg/ m2) after the first AM
EPOXICOTE 402F layer has dried (4-6 hours)
AM EPOXICOTE 402F
Step 4: Protect AM EPOXICOTE 402F layer from damp ,condensation and water at least 2 days after
application, Epoxy system should be ready in use after 7 days.
Step 5: Do fluid test after 7 days, within 48-72 hours .
PART 6 SWIMMING POOL
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
(AM FLEXPROOF 502)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
FINISHING LAYER
R.C. WALL, SLAB
FILLET
PROTECTION SCREED
FULLY MESH REINFORCEMENT
AM FLEXPROOF 502
W.P LAYER - MESH REINFORCEMENT: AM FLEXPROOF 502
AM FLEXPROOF 502
W.P 2 LAYERS: AM FLEXPROOF 502
WATERPROOFING METHOD STATEMENT FOR SWIMMING POOL
DETAIL BDETAIL A
Protection screed
Fillet
Finishing layer
Full mesh reinforcement
2 L AM FLEXPROOF 502
W.P 2 layer: AM FLEXPROOF 502
R.C. wall, slab
Finishing layer
2 L AM FLEXPROOF 502
W.P 2 layer: AM FLEXPROOF 502
Protection screed
R.C. wall, slab
Full mesh reinforcement
Protection screed
Finishing layer
Non-shrink grout
PIPE TREATMENT
Full mesh reinforcement
L
AM FLEXPROOF 502
W.P layer - Mesh reinforcement: AM FLEXPROOF 502
L
AM FLEXPROOF 502
W.P layer - Mesh reinforcement: AM FLEXPROOF 502
2 L
AM FLEXPROOF 502
W.P 2 layer: AM FLEXPROOF 502
L
AM FLEXPROOF 502
W.P layer - Mesh reinforcement: AM FLEXPROOF 502
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
R.C. slab
SWIMMING POOL
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
Waterproofing area
Product
Remark
Swimming pool
AM FLEXPROOF 502
2.5 Kg/ m
2
Construction joint
AM FLEXSTOP IC 250
NOTE(S):
DETAIL A
DETAIL B
LEAN CONCRETE
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
AM SEAL PU1
AM SEAL PU1 sealant
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
/ MIXING:
Pour Part A (liquid) into a pail, and pour Part B (powder) slowly into the pail and mix with a low speed
mixing machine or with paddle by hand. Mix until a slurry of even consistency is achieved (apx. 3minutes).
AM FLEXPROOF 502:
METHOD STATEMENT OF AM FLEXPROOF 502:
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. Must
be removed by mechanical method .
2. C c ong c
Repair honey comb concrete by latex motar .
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with
latex motar.
ch n ng
Repair construction joints by mesh reinforcement.
Do fillet at corner.
Pipe treatment (if any).
Pre-water or damp the surface prior to application
III. APPLICATION:
2
Step 1: Apply first coat (consumption 0.8 kg/m
2
), over the pre-wetted wall, slab and reinforcement.
Step 2: Apply reinforced fiber mesh when 1
st
coat is still wet, ensure the mesh is fully in contact with 1
st
coat.
2
).
Step 3: Apply second coat (consumption 0.8 kg/m
2
) after the first coat has dried (4-5 hours).
2
)
Step 4: Apply third coat (consumption 0.9 kg/m
2
) after the second coat has dried (4-5 hours).
B c 5: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 5: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 6: Screeding/ plastering for protection after fluid test.
SWIMMING POOL
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
Waterproofing layer
Mesh reinforcement
PART 7 TOILET, BALCONY, WET AREA
(AM FLEXPROOF 501)
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR TOILET, BALCONY, WET AREA
300
DETAIL A
R.C. wall, slab
Finishing layer
DETAIL B
R.C WALL, SLAB
FINISHING LAYER
FILLET
W.P LAYER - CORNETR REINFORCEMENT
AM FLEXPROOF 501
W.P LAYER: AM FLEXPROOF 501
PIPE TREATMENT
Finishing layer
W.P layer - Corner reinforcement
R.C. wall, slab
Fillet
DETAIL A
DETAIL B
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout.
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
Mesh - Corner reiforcement
MESH - CORNER REINFORCEMENT
PROTECTION SCREED
Protection screed
Protection screed
Waterproofing area
Product
Remark
Standing bath
AM FLEXPROOF 501
NOTE(s):
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
AM SEAL PU1
AM SEAL PU1 sealant
R.C wall, slab
W.P layer - Corner reinforcement
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXPOOF 501
W.P layer: AM FLEXPROOF 501
Finishing layer
Mesh - Corner reiforcement
Protection screed
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
Waterproofing area
Product
Remark
Standing bath
AM FLEXPROOF 501
NOTE(s):
DETAIL B
R.C WALL, SLAB
FINISHING LAYER
PROTECTION SCREED
FILLET
W.P LAYER - CORNETR REINFORCEMENT
MESH - CORNER REINFORCEMENT
DETAIL A
WATERPROOFING METHOD STATEMENT FOR STANDING BATH
AM FLEXPROOF 501
W.P LAYER: AM FLEXPROOF 501
R.C. wall, slab
Finishing layer
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
Protection screed
DETAIL A
DETAIL B
1500
Finishing layer
W.P layer - Corner reinforcement
R.C. wall, slab
Fillet
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
Mesh - Corner reiforcement
Protection screed
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout.
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
PIPE TREATMENT
AM SEAL PU1
AM SEAL PU1 sealant
R.C wall, slab
W.P layer - Corner reinforcement
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXPOOF 501
W.P layer: AM FLEXPROOF 501 Finishing layer
Mesh - Corner reiforcement
Protection screed
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
300
H
WATERPROOFING METHOD STATEMENT FOR BATHTUB
DETAIL A
R.C WALL, SLAB
FINISHING LAYER
PROTECTION SCREED
DETAIL B
FILLET
W.P LAYER - CORNETR REINFORCEMENT
MESH - CORNER REINFORCEMENT
300
Waterproofing area
Product
Remark
Bathtub
AM FLEXPROOF 501
NOTE(s):
Fillet
Brick wall
DETAIL B
DETAIL A
Finishing layer
Mesh - Corner reinforcement
W.P layer - Corner reinforcement
Protection screed
R.C. wall, slab
Protection screed
Finishing layer
Brick wall or kicker
AM FLEXPROOF 501
W.P LAYER: AM FLEXPROOF 501
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
PIPE TREATMENT
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout.
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
AM FLEXPROOF 501
W.P layer: AM FLEXPROOF 501
AM SEAL PU1
AM SEAL PU1 sealant
R.C wall, slab
W.P layer - Corner reinforcement
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXPOOF 501
W.P layer: AM FLEXPROOF 501 Finishing layer
Mesh - Corner reiforcement
Protection screed
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
APPLICATION:
Step 1: Apply one coat stick mesh at corner of wall - slab.
2
n, ng c o .
Step 2: Apply first coat (consumption 0.8 kg/m
2
), over the pre-wetted wall, slab.
2
).
Step 3: Apply second coat (consumption 0.8 kg/m
2
) after the first coat has dried (4-5 hours).
2
)
Step 4: Apply third coat (consumption 0.9 kg/m
2
) after the second coat has dried (4-5 hours).
Step 5: Do fluid test within 48-72 hours.
Step 6: Screeding/ plastering for protection after fluid test.
/ MIXING:
Pour Part A (liquid) into a pail, and pour Part B (powder) slowly into the pail and mix with a low speed
mixing machine or with paddle by hand. Mix until a slurry of even consistency is achieved (apx. 3minutes).
METHOD STATEMENT
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc.
Must be removed by mechanical method.
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole
with latex motar.
ch n ng
Repair construction joints by mesh reinforcement.
Do fillet at corner .
Pipe treatment (if any).
Pre-water or damp the surface prior to application.
Waterproofing layer
Mesh reinforcement
Waterproofing layer
PART 8. R.C ROOF, TERRACE
(AM FLEXPROOF 503 PU/ VISCOGUM SAND)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout.
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
WATERPROOFING METHOD STATEMENT FOR R.C ROOF, TERRACE
R.C. WALL, SLAB
PROTECTION CONCRETE
MESH - CORNER REINFORCEMENT
P.E FILM LAYER
AM FLEXPROOF 503 PU
W.P LAYER: AM FLEXPROOF 503 PU
THERMAL INSULATION XPS FOAM
NOTE(s):
EXPANSION JOINT
300
DETAIL B
BRICK WALL
i
i
PIPE TREATMENTDETAIL A DETAIL B
R.C. wall, slab
PE film layer
Primer layer
Thermal insulation XPS foamProtection concrete
Protection screed
R.C. wall, slab
Primer layer
PE film
Mesh - Corner reinforcement
R.C. wall, slab
White foam
Primer layer
Thermal insulation XPS foam
PRIMER LAYER
DETAIL A
L
AM FLEXPROOF 503 PU
W.P layer: AM FLEXPROOF 503 PU
L
AM FLEXPROOF 503 PU
W.P layer:
AM FLEXPROOF 503 PU
L AM FLEXPROOF 503 PU
W.P layer: AM FLEXPROOF 503 PU
Protection concrete
Waterproofing area
ProductRemark
R.C roof, terrace
AM FLEXPROOF 503 PU
AM SEAL PU1
AM SEAL PU1 sealant
AM GROUT 307
Non-shrink Grout AM GROUT 307
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
METHOD 1
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
METHOD STATEMENT
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc.
Must be removed by mechanical method.
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole
with latex motar.
ch n ng
Repair construction joints by mesh reinforcement.
Do fillet at corner
Pipe treatment (if any)
/ APPLICATION:
Step 1: Apply primer layer onto wall - slab treated.
Step 2: Apply first coat (consumption 0.75 kg/m2) after primer layer has dried and stick mesh reinforcement
mesh at corner of wall - slab.
Step 3: Apply second coat (consumption 0.75 kg/m2) after first coat has dried (2-4 hours).
B c 4: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 4: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 5: Screeding/ plastering for protection after fluid test.
Waterproofing layer
Mesh reinforcement
Waterproofing layer
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
Waterproofing area
Product
Remark
R.C roof , Terrace
VISCOGUM SAND 3MM
R.C. WALL, SLAB
PROTECTION CONCRETE
P.E FILM LAYER
THERMAL INSULATION XPS FOAM
NOTE(s):
EXPANSION JOINT
R.C ROOF, TERRACE, GUTTER
PIPE TREATMENTDETAIL C
R.C. wall, slab
PE film layer
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
Thermal insulation XPS foam
Protection concrete
AM FLEXPROOF 521WB
PRIMER LAYER AM FLEXPROOF 521WB
DETAIL A
Protection screed
DETAIL D
R.C. wall, slab
PE film layer
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
Thermal insulation XPS foam
Protection concrete
PE film layer
150
WATERPROOFING METHOD STATEMENT FOR R.C ROOF, TERRACE, GUTTER
DETAIL B
300
DETAIL D
Brick wall
i
i
DETAIL C
DETAIL A
DETAIL B
Protection screed
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
R.C. wall, slab
Brick wall
Fillet
AM SEAL PU1
AM SEAL PU1 sealant
Aluminum splint 20x20mm
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
AM SEAL PU1
AM SEAL PU1 sealant
AM Grout 307
Non-shrink grout AM Grout 307
Protection screed
R.C. wall, slab
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
PE film
Thermal insulation XPS foam
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
VISCOGUM SAND 3MM
WP layer: VISCOGUM SAND 3MM
@300mm
METHOD 2
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
PART 9. R.C ROOF.
(VISCOGUM SLATED/ AM FLEXPROOF 504 PU)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, VietnamT. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
WATERPROOFING METHOD STATEMENT FOR R.C ROOF, GUTTER
DETAIL B
300
DETAIL C
i
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
R.C. WALL, SLAB
NOTE(s):
R.C ROOF, GUTTER
PIPE TREATMENTDETAIL B
PRIMER LAYER
R.C. wall, slab
Primer layer
DETAIL C
R.C. wall, slab
Primer layer
AM SEAL PU1
AM SEAL PU1 sealant
AM Grout 307
Non-shrink grout AM Grout 307
R.C. wall, slab
Primer layer
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
AM FLEXPROOF 504 PU
WP layer: AM FLEXPROOF 504 PU
AM FLEXPROOF 504 PU
WP LAYER: AM FLEXPROOF 504 PU
AM FLEXPROOF 504 PU
WP layer: AM FLEXPROOF 504 PU
AM FLEXPROOF 504 PU
WP layer: AM FLEXPROOF 504 PU
Fillet
METHOD 2
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
i
ii
Waterproofing area
ProductRemark
R.C roof, terrace
AM FLEXPROOF 504 PU
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
METHOD STATEMENT
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc.
Must be removed by mechanical method.
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole
with latex motar.
ch n ng
Repair construction joints by mesh reinforcement.
Do fillet at corner
Pipe treatment (if any)
/ APPLICATION:
Step 1: Apply primer layer onto wall - slab treated.
Step 2: Apply first coat (consumption 1.0 kg/m2) after primer layer has dried and stick mesh reinforcement
mesh at corner of wall - slab.
Step 3: Apply second coat (consumption 1.0 kg/m2) after first coat has dried (2-4 hours).
B c 4: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 4: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Waterproofing layer
Mesh reinforcement
Waterproofing layer
WATERPROOFING METHOD STATEMENT FOR R.C ROOF, GUTTER
DETAIL B
300
DETAIL C
i
DETAIL A
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
tinh.
Remove all dust, debris, bricks, stones, and standing water,...
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to concrete
surface
After installed and filled with grout, penetration pipes cut off closely to concrete
slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together with
R.C. slab
Waterproofing area
Product
Remark
R.C roof , Gutter
VISCOGUM SLATED
R.C. WALL, SLAB
NOTE(s):
R.C ROOF, GUTTER
PIPE TREATMENTDETAIL B
AM FLEXPROOF 521WB
PRIMER LAYER AM FLEXPROOF 521WB
DETAIL A
R.C. wall, slab
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
DETAIL C
R.C. wall, slab
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
AM SEAL PU1
AM SEAL PU1 sealant
AM Grout 307
Non-shrink grout AM Grout 307
R.C. wall, slab
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
AM FLEXSWELL
AM FLEXSWELL swellable
rubber or bentonite strip.
VISCOGUM SLATED
WP layer: VISCOGUM SLATED
VISCOGUM SLATED
WP LAYER: VISCOGUM SLATED
VISCOGUM SLATED
WP layer: VISCOGUM SLATED
VISCOGUM SLATED
WP layer: VISCOGUM SLATED
AM SEAL PU1
AM SEAL PU1 sealant
AM FLEXPROOF 521WB
Primer layer AM FLEXPROOF 521WB
VISCOGUM SLATED
WP layer: VISCOGUM SLATED
Aluminum splint 20x20mm
Fillet
@300mm
METHOD 1
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
i
ii
PART 10 PODIUM SLAB
PRODUCT
(AM PLEXPROOF 503 PU)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
R.C. WALL, SLAB
PRIMER LAYER
FILLET
AM FLEXPROOF 503 PU
W.P LAYER: AM FLEXPROOF 503 PU
PROTECTION SCREED
MESH - CORNER REINFORCEMENT
DETAIL A DETAIL B
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to
concrete surface
After installed and filled with grout, penetration pipes cut off closely to
concrete slab surface (avoid impacting on them after waterproofing)
Do not cover with ciment mortar prior to waterproofing; a minimium 300mm
height of parapet wall should be left for reinforcement
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Conduction pipe should be built at least 500mm height for waterproofing
reinforcement
Kicker must be cast min. 200mm at parapet wall, should be cast together
with R.C. slab
WATERPROOFING METHOD STATEMENT FOR PODIUM SLAB
Primer layer
AM FLEXPROOF 503 PU
W.P layer: AM FLEXPROOF 503 PU
R.C. Slab
Protection screed
Fillet
Mesh - Corner reinforcement
AM FLEXPROOF 503 PU
W.P layer: AM FLEXPROOF 503 PU
Protection screed
R.C. wall, slab
Primer layer
Waterproofing area
Product
Podium slab
AM FLEXPROOF 503 PU
1.5 kg/m
2
DETAIL ADETAIL B
AM FLEXPROOF 503 PU
AM FLEXSWELL
AM FLEXSWELL SWELLABLE RUBBER OR
BENTONITE STRIP.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
II. / APPLICATION:
Step 1: Apply primer layer onto wall - slab treated.
Step 2: Apply first coat (consumption 0.75 kg/m2) after primer layer has dried and stick mesh
reinforcement mesh at corner of wall - slab.
Step 3: Apply second coat (consumption 0.75 kg/m2) after first coat has dried (2-4 hours).
B c 4: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 4: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 5: Screeding/ plastering for protection after fluid test.
AM FLEXPROOF 503 PU:
METHOD STATEMENT - AM FLEXPROOF 503 PU:
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc.
Must be removed by mechanical method
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole
with latex motar.
ch n ng, khe n n b b ng c ch c
a ng
Repair construction joints by chip of form V after fill non-shink grout (if any).
Do fillet at corner
Pipe treatment (if any)
V-Shape hackFill with Grout
Apply Waterproofing layer
PART 11 PLANTER BOX, LANDSCAPE
PRODUCT
(AM FLEXPROOF 502 &
AM FLEXPROOF 503 PU)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
DETAIL BDETAIL A
Waterproofing area
Product
Remark
Planter box, Landscape
AM FLEXPROOF 502
AM FLEXPROOF 503 PU
2.5 Kg/m
2
1.5 Kg/m
2
Protection screed
R.C. wall, slab
FINISHING LAYER (IF ANY)
R.C. WALL, SLAB
FILLET
PROTECTION SCREED
AM FLEXPROOF 502
W.P LAYER - REINFORCEMENT: AM FLEXPROOF 502
FIRBE GLASS - REINFORCEMENT
Protection screed
Fillet
R.C Wall
Fiberglass mesh - Reinforcement
WATERPROOFING METHOD STATEMENT FOR PLANTER BOX, LANDSCAPE
PIPE TREATMENT
AM SEAL PU1
AM SEAL PU1 sealant
Fiberglass mesh - Corner reiforcement
W.P layer - Corner reiforcement
R.C wall, slab
AM GROUT 307
Non-shrink Grout AM GROUT 307
Protection screed
Finishing layer
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
Finishing layer (if any)
DETAIL A
Finishing layer (if any)
REQUIREMENTS OF SURFACES NEED TO BE WATERPROOFED
Remove forms, steel and wooden supports
Remove all dust, debris, bricks, stones, and standing water
Cut off unnecessary steel bars or tie-rods in minimum 20mm depth to
concrete surface
After installed and filled with grout, penetration pipes cut off closely to
concrete slab surface (avoid impacting on them after waterproofing)
Any protrusions must be hacked for a flat surface on design requirement
Any honeycomb spots or voids must be removed for a sound concrete and
poured concrete again on design requirement
Kicker must be cast min. 200mm at parapet wall, should be cast together
with R.C. slab
AM FLEXPROOF 502
W.P LAYER: AM FLEXPROOF 502
PRIMER LAYER
MESH - CORNER REINFORCEMENT
AM FLEXPROOF 503 PU
W.P LAYER: AM FLEXPROOF 503 PU
R.C Wall, Slab
Reinforcing mesh
DETAIL C
Mesh - Corner
reinforcement
Primer layer
AM FLEXPROOF 503 PU
W.P layer: AM FLEXPROOF 503 PU
Protection screed
Finishing layer (if any)
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
Protection screed
DETAIL A DETAIL B
DETAIL C
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXPROOF 502
W.P layer: AM FLEXPROOF 502
AM FLEXSWELL
AM FLEXSWELL swellable rubber or
bentonite strip.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
/ MIXING:
Pour Part A (liquid) into a pail, and pour Part B (powder) slowly into the pail and mix with a low speed
mixing machine or with paddle by hand. Mix until a slurry of even consistency is achieved (apx. 3minutes).
AM FLEXPROOF 502:
METHOD STATEMENT - AM FLEXPROOF 502:
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. Must be
removed by mechanical method
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with
latex motar.
ch n ng, khe n n b b ng c ch c
a ng
Repair construction joints by chip of form V after fill non-shink grout (if any).
Do fillet at corner
Pipe treatment (if any)
Pre-water or damp the surface prior to application
V-Shape hackFill with Grout
Apply Waterproofing layer
III. APPLICATION:
2
Step 1: Apply first coat (consumption 0.8 kg/m
2
), over the pre-wetted wall, slab and reinforcement.
Step 2: Apply reinforced fiber mesh when 1
st
coat is still wet, ensure the mesh is fully in contact with 1
st
coat.
2
).
Step 3: Apply second coat (consumption 0.8 kg/m
2
) after the first coat has dried (4-5 hours).
2
)
Step 4: Apply third coat (consumption 0.9 kg/m
2
) after the second coat has dried (4-5 hours).
B c 5: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 5: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 6: Screeding/ plastering for protection after fluid test.
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
II. / APPLICATION:
Step 1: Apply primer layer onto wall - slab treated.
Step 2: Apply first coat (consumption 0.75 kg/m2) after primer layer has dried and stick mesh
reinforcement mesh at corner of wall - slab.
Step 3: Apply second coat (consumption 0.75 kg/m2) after first coat has dried (2-4 hours).
B c 4: Sau khi hai (72 ng). n nh n c trong ng 48 .
Step 4: After the second coat has dried (72 hours). Do fluid test within 48 hours.
Step 5: Screeding/ plastering for protection after fluid test.
AM FLEXPROOF 503 PU:
METHOD STATEMENT - AM FLEXPROOF 503 PU:
SURFACE PREPARATION:
1. sinh lo b c c c n b n a, c b n D ng
sinh b .
All adhesion inhibiting substances such as dirt, cement, oil, hardeners, loose components, paint etc. Must be
removed by mechanical method
2. C c ong c
Repair honey comb concrete by latex motar.
b ng c ch c ng 50x50mm sau b ng a latex
Cut back any protrusions and patching coin holes by chip to form a hole 50x50mm then fill the hole with
latex motar.
ch n ng, khe n n b b ng c ch c
a ng
Repair construction joints by chip of form V after fill non-shink grout (if any).
Do fillet at corner
Pipe treatment (if any)
V-Shape hackFill with Grout
Apply Waterproofing layer
PART 12 CONSTRUCTION JOINT
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
(AM FLEXSTOP IC 250 &
AM FLEXSWELL)
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
CONSTRUCTION JOINT
(AM FLEXSTOP IC 250)
SAMPLE PICTURE
CONSTRUCTION JOINT FOR R.C SLAB
AM FLEXSTOP IC 250
Metal wire
Metal wire
Steel bar fixed
AM FLEXSTOP IC 250
125
Metal wire
125
CONSTRUCTION JOINT FOR R.C WALL
250
25
0
LEAN CONCRETE
R.C WALL, SLAB
AM FLEXSTOP IC 250
WATERSTOP: AM FLEXSTOP IC 250
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
CONSTRUCTION JOINT
AM FLEXSTOP IC 250
Steel bar fixed
AM FLEXSTOP IC 250
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
CONSTRUCTION JOINT
(AM FLEXSWELL)
LEAN CONCRETE.
R.C WALL, SLAB.
AM FLEXSWELL
AM FLEXSWELL SWELLABLE RUBBER
OR BENTONITE STRIP.
SAMPLE PICTURE
CONSTRUCTION JOINT FOR R.C WALL
CONSTRUCTION JOINT FOR R.C SLAB
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
CONSTRUCTION JOINT
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
PART 13 TREATMENT METHOD FOR TIE-ROD
TREATMENT METHOD FOR TIE-ROD
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn
CEMENT : SAND = 1 : 3 (A)
-
LATEX : WATER = 1 : 3 (B)
-
MIXING A & B TO CREATE MORTAR LATEX
MIXING (1 : 3)
TREATMENT METHOD FOR TIE-ROD
30
SECTION TYPICAL
STEP 1: PUNCH A HOLE 50X70MM, DEPTH 30mm STEP 2: CUT TIE-ROD & CLEAN CONCRETE
AM FLEXPROOF 502
STEP 4: APPLY 2 W.P AM FLEXPROOF 502
& REINFORCING MESH
W.P layer
Punch tie-rod
Tie-rod
Reinforcing mesh(150x150)
W.P layer
Tie-rod
Tie-rod
Punch tie-rod
Tie-rod
STEP 3: FILL WITH LATEX MORTAR
(MIX: 1/ 3)
Fill with latex mortar
Fill with latex mortar
Fill with latex mortar
REV
00
TEL.:
E-mail: Website:
ADD .:
Add: R.205, City View,12 Mac Dinh Chi Str.,
Da Kao Ward, Dist. 1, HCMC, Vietnam
Tel: (84-28) 38208686 / 38207126 Fax: (84-28) 38208866
Website: www.asiamortar.com
TREATMENT METHOD FOR TIE-ROD
ASIA MORTAR COMPANY LIMITED: R.205, City View, No 12 Mac Dinh Chi street, Da Kao ward, District 1, Ho Chi Minh City, Vietnam
T. (+84) 28 3820 8686 | H. (+84) 9 18 28 88 11 | E. [email protected] | W. www.asiamortar.vn