TECHNOLOGICAL COMPARISON: INTENSIFIERS © 2012 CMS SPA - All rights reserved. This document is strictly confidential; CMS SPA reserves according to the.

TECHNOLOGICAL COMPARISON: INTENSIFIERS

© 2012 CMS SPA - All rights reserved. This document is strictly confidential; CMS SPA reserves according to the law the ownership of this document with prohibition to reproduce it and to communicate it to bystanders without CMS SPA's written authorization

Parallel intensifiers Opposed twin Intensifiers

TECHNOLOGY

Power drive Pump Electric Servo Pump

Advantages parallel intensifiers:

-Constant pressure signal = high quality cut- Redundancy (can run with only 2 intensifiers and do the any maintenance when you decide not when the machine breaks down)- No attenuator to be replaced.- Low Cycle time: 30 cycle/minute = Long time between replacement (all things equal there is less wear per hour with 3 intensifiers = longer time between seal replacement)- Air/oil heat exchanger (integrated)

PARALLEL INTENSIFIER

Disadvantages opposed twin intensifiers

- Pressure drops = less quality- No redundancy (production at the mercy of breakdowns)- Attenuator needed (reservoir) that has to be replaced (€ 5.000/10.000)- High Cycle time: 60 cycle/minute = High maintenance costs- Water/oil heat exchanger

OPPOSED TWIN INTENSIFIER

POWER DRIVE PUMP

Disadvantages pd intensifiers

- Ultre High Cycle time: 300 cycle/minute = Ultra High maintenance costs due to the high speed and temperature- Working pressure: maximum pressure of 3800 bar = less cutting speed/quality- No redundancy (production at the mercy of breakdowns)- Pump flowrate fixed = high water consumption (water is consumed also when the head is closed)- Intensifier normally used for hydro cleaning applications = low cost, low pressure, low speed

Disadvantages electric servo pump

-High Cycle time: 60 cycle/minute = High maintenance costs due to the high speed and temperature- Working pressure: maximum pressure of 3800 bar = less cutting speed/quality- No redundancy (production at the mercy of breakdowns)- Attenuator needed (reservoir) that has to be replaced (€ 5.000/10.000)- New technology: how many pump Techni already installed?

ELECTRIC SERVO PUMP

SINGLE EFFECT MULTIPLIERS

DOUBLE EFFECT MULTIPLIERS

SINGLE EFFECT MULTIPLIERS WITH

ENGINE DIRECT DRIVE

ELECTRIC SERVO PUMP

WORKING PRESSURE

60.000 psi (4.100 Bar)

60.000 psi (4.100 Bar) 55.000 psi (3.800 Bar) 55.000 psi (3.800 Bar)

REDUNDANCY

Yes: possibility to work also when there it is necessary to make maintenance to one cylinder

No: machine downtime No: machine downtime No: machine downtime

WATER FLOWRATE

= = > =

OPERATING COSTS

> electric power - < water

> electric power - > water

< electric power - < water

< electric power - < water

PISTONS CYCLES

Low (30 cycle/minute)

Middle (60 cycle/minute)

High (300 cycle/minute) Middle (60 cycle/minute)

MAINTENANCE COSTS

Low Middle High Middle

PUMP FLOWRATE

Varying Varying Fixed Varying

NOISE High Middle Low Low

COMPARISON

KMT SL-V 60 PLUS OMAX P4055V TECHNI ESP 55

POWER 45 kW (60 Hp) 45 kW (60 Hp) 30 kW (40 Hp)

INTENSIFIERHYDRAULIC WITH

THREE INTENSIFIERS

HYDRAULIC WITH TWO INTENSIFIERS

ELECTRIC WITH THREE PISTONS

ELECTRIC WITH TWO INTENSIFIERS

MAX PRESSURE 4150 bar 4150 bar 3800 bar 3800 bar

WATER FLOW RATE 5 l/min 4,5l/min 4 l/min 3,8l/min

MAX ORIFICE SIZE 0,40mm 0,38mm 0,38mm 0,35mm

COMPARISON

9

TECNOCUT INTENSIFIERS RANGE

10

4100 BAR INTENSIFIERS

11

6200 BAR INTENSIFIERS

www.cms.it

www.tecnocut.it

THANK YOU

© 2011 CMS SPA - All rights reserved. This document is strictly confidential; CMS SPA reserves according to the law the ownership of this document with prohibition to reproduce it and to communicate it to bystanders without CMS SPA's written authorization