Blohm + Voss Pipe Handling Equipment ABVC-200 Sliptype Elevator Manual PN 672600-Y-D Rev 003, February 2012 Technical Documentation Original Instructions Blohm + Voss Oil Tools
1
Blohm + Voss Pipe Handling Equipment
ABVC-200 Sliptype Elevator
Man
ual P
N 6
726
00
-Y-D
Rev
00
3, F
ebru
ary
2012
Technical Documentation
Original Instructions
Blohm + Voss Oil Tools
2
Improper / Unsafe Use
The tool must only be used for the designated purpose. When using the tool, the rated load must never be exceeded.
GENERAL INFORMATION
Intended use of this manual
This manual is intended for use by field service, engineering, installation, operation, and repair personnel. Every effort has been made to ensure the accuracy of the information contained herein. Blohm + Voss Oil Tools, will not be held liable for errors in this material, or for consequences arising from misuse of this material.Anyone using service procedures or tools, whether or not recommended by Blohm + Voss Oil Tools, must be thoroughly satisfied that neither personal safety nor equipment safety will be jeopardized.
Intellectual property
All rights retained. No part of this document may be reproduced in any form (print, photocopy, microfilm or any other procedure) or be processed using an electronic system without written approval of Blohm + Voss Oil Tools.All information contained in this manual is based upon the latest product information available at any time of printing. Dependent on ongoing technical improvements (ISO 9001) “Blohm + Voss Oil Tools” reserves the right to change the design and specifications without announcement. The values specified in this manual represent the nominal values of a unit produced in series. Slight deviations in the case of the individual devices are possible.
NOTE: In the event of problems that cannot be solved with the aid of this manual, please contact one of the addresses listed below.
Warnings and Note
WARNING: A “WARNING” INdIcAtes A defINIte RIsk of equIpmeNt dAmAGe oR dANGeR to peRsoNNel. fAIluRe to obseRve ANd folloW pRopeR pRoceduRes could Result IN seRIous oR fAtAl INjuRy to peRsoNNel, sIGNIfIcANt pRopeRty loss, oR sIGNIfIcANt equIpmeNt dAmAGe.
NOTE: A “note” indicates that additional information is provided about the current topics.
WARNING: thIs techNIcAl documeNtAtIoN coNtAINs INstRuctIoNs oN sAfety, INstAllAtIoN, opeRAtIoN ANd mAINteNANce foR the blohm + voss oIl tools tool . It must be studIed befoRe WoRkING WIth the tool.
CE Marking
The tool complies with the Machinery Directive 98/37/EC and 2006/42/EC
For machines containing any hydraulic or pneumatic powered parts, the Directive 94/9/EC “Equipment and protective systems in potentially explosive atmospheres” applies.The marking is as follows:CE Ex II 2G T5 (hydraulic tools) or CE Ex II 2G T6 (pneumatic tools).
Manufacturer & Agents World wide
Limited Warranty
The warranty provided will be void if the tool is either:1. Repaired or serviced by
a service facility which was not authorised by Blohm + Voss Oil Tools.
2. Replacement parts not manufactured by Blohm+Voss Oil Tools are used.
3. Modifications were made to the tool which were not approved by Blohm+Voss Oil Tools.
Blohm + Voss Oil ToolsHermann-Blohm-Straße 220457 HamburgGermany
Phone: +49 40/3119-1826/1162 Fax: +49 40/[email protected]
Premier Sea & Land Pte. Ltd.1, Scotts Road #19-12 Shaw CentreSingapore 228208Republic of Singapore
Phone: +65-6734-7177Fax: [email protected]
Blohm + Voss Oil Tools, LLC7670 Woodway, Suite 266 Houston, Texas 77063United States of America
Phone: +1-713-952 0266Fax: +1-713-952 [email protected]
3
General safety issues
WARNING: oNe should AvoId cReAtING IGNItIoN souRces, lIke heAt, As A Result of the use of the tool WIth otheR tools oR equIpmeNt.
WARNING: do Not use the tool foR ANy otheR puRpose thAN GIveN IN thIs documeNt WIthIN It̀ s specIfIcAtIoN.
WARNING: fAIluRe to coNduct RoutINe mAINteNANce could Result IN equIpmeNt dAmAGe oR INjuRy to peRsoNNel.
WARNING: WeAR peRsoNAl pRotectIoN equIpmeNt WhIle WoRkING WIth the equIpmeNt.
WARNING: If ANy sAfety elemeNts (lIke sAfety Ropes, sAfety sheets, plAtes oR WAsheRs) WeRe dIsAssembled due to mAINteNANce WoRk, do Not Re-use them. AlWAys ReplAce them WIth NeW sAfety elemeNts.
WARNING: All WARNING plAtes, sIGNs ANd lAbels AttAched to the equIpmeNt must be obseRved. the WARNING plAtes, sIGNs ANd lAbels must be pReseNt oN the tool. do Not Remove the lAbels. If they ARe mIssING, ReplAcING Is mANdAtoRy.
WARNING: ANy modIfIcAtIoN to the tool cARRIed out WIthout the AppRovAl of blohm + voss oIl tools WIll voId ANy WARRANty.
WARNING: usING the tool WIth dAmAGed oR WoRN pARts cAN cReAte seRIous INcIdeNts.
WARNING: It Is Not AlloWed to use ANy compoNeNts WhIch ARe of "NoN-b+v" oRIGINe, oR use "NoN-oem" pARts WhIch ARe Not AppRoved by b+v. It WIll voId ANy WARRANty ANd mAy effect the coRRect fuNctIoNING of the tool ANd It's sAfety feAtuRes.
WARNING: the compANy opeRAtING the tool Is RespoNsIble foR evAluAtING sAfe ANd pRopeR use of the tool IN A hAzARd ANAlysIs.
WARNING: the opeRAtING compANy Is oblIGAted to Issue WoRkING INstRuctIoNs foR sAfe use ANd supeRvIse obseRvANce of these WoRkING INstRuctIoNs.
WARNING: eveRy employee, WhIch opeRAtes, seRvIces, INspects oR otheRWIse INvolved WIth the use of the tool IN otheR AReAs hAs to eNsuRe, thAt these ActIoNs ARe doNe by tRAINed ANd by AN blohm + voss oIl tools AuthoRIzed peRsoNNel,ANd should complete ReGulAR couRses of tRAINING, to eNsuRe pRopeR use As Well As sAfe opeRAtIoN, coRRect mAINtAINANce ANd INspectIoN.
WARNING: If NecessARy, A ReAsoNAble, AddItIoNAl supeRvIsoR should be AppoINted duRING opeRAtIoN.
WARNING: stAy AWAy fRom the tool duRING opeRAtIoN. IN cAse It Is Remote opeRAted It mAy mAke movemeNts WIthout WARNING.
Warning sign PN 671638General warning
Warning sign PN 671642Pay attention: Apply grease at least once a day.
Warning sign PN 611524Danger: Do not touch.
Warning sign PN 671640-1Pay attention: Do not place your hands between moving parts.
Warning sign PN 671641Pay attention: Risk of crushing.
Safety issues elevator
WARNING: do NeveR uNlAtch/opeN the tool WhIle A pIpe Is suspeNded IN the tool; the pIpe WIll be lost!
WARNING: WhIle usING the elevAtoR, AlWAys mAke suRe the dooR Is completely closed WIth the lAtch/lAtch lock fully eNGAGed ANd If ApplIcAble the veRIfIcAtIoN pIN pRopeRly INstAlled.
WARNING: pAy specIAl AtteNtIoN to the veRIfIcAtIoN pIN (If ApplIcAble), lAtch ANd lAtch lock foR ANy sIGNs of WeAR, beNdING oR dAmAGe At ANy tIme. IN cAse pARts ARe dAmAGed oR beNt, ReplAce ImmedIAtelly by NeW, oRIGINAl pARts.
Safety issues automatic elevators
WARNING: eNsuRe the coNNectoRs ARe fRom A mAle ANd femAle type to pReveNt fAulty coNNectIoNs.
4
Warning signs.
On the following pages warning signs and their relative positions are shown.
Warning sign „Warning“ PN 613684
Warning sign „Automatic“ PN 613639
Warning sign „Danger“ PN 671637
Warning sign PN 671636
5
We,
Blohm + Voss Oil Tools Hermann-Blohm-Strasse 2 20457 Hamburg Phone:+49(0)40 3119-1139Fax:+49(0)40 3119-3305
declare that the product
ABVC 150-200 Sliptype Elevator
which is the subject of this declaration, is in conformity with the following standard(s) or normative documents 98/37/EC: Machinery Directive 2006/42/EC: Machinery Directive from 31 December 2009.DIN EN ISO 12100 : Safety of machinery, part 1 and 2 DIN EN ISO 14121-1: Safety of machinery, Risk assessment Directive 94/9/EC: Devices and protection systems for intended use in explosive areas DIN EN 13463-1:2009-07: Non-electrical equipment for use in potentially explosive atmospheres ISO 13535:2002/API 8C: Petroleum and natural gas industries-Drilling and production equipment-Hoisting equipment
Marking: II 2G T6
EC-DECLARATION OF CONFORMITY
6
Table of contents
GENERAL INFORMATION 2
Warnings and Note 2Intended use of this manual 2Intellectual property 2Improper / Unsafe Use 2Manufacturer & Agents World wide 2CE Marking 2Limited Warranty 2General safety issues 3Safety issues elevator 3Safety issues automatic elevators 3Warning signs. 4
EC-DECLARATION OF CONFORMITY 5
Table of contents 6
1. Description 10
General 10Features 10Options 10Main assembly 10Improper / Unsafe Use 11Limited Warranty 11Identification 11Technical Data 12Contents of delivery 12Main Dimensions ABVC-200 Sliptype elevator 13Main components & functioning 14Functioning 14
2. Commissioning 16
Commissioning ABVC-200 Elevator 16Scope of supply 16Pneumatic Characteristics 16Check and Lubrication 16Function Test 17
3. Installation 20
Lifting and transport 20Pneumatic functioning 20Installation of pneumatic Parts 20Installation of Elevator 21Installing and removing the required Slips 21Installation Checklist ABVC-200 Elevator 22Pneumatic Connections 22Function test 22
4. Operations 24
Safety 24Operation MU (make up) 24Operation BO (break out) 24Connecting and disconnecting of the pneumatic hoses 24Manual Opening in Case of Emergency 25Manual Closing of the Elevator 26Handling the Trigger Closing Tool 26
5. Maintenance and Inspection 32
General 32Daily Lubrication 32Daily Inspection 32Grease points 32Daily Test 32Locking of screws 32Grease Quality 33Inspection categories acc. to API RP 8B 34Frequency 34Periodic inspection 34Non-periodic inspection 34Inspection 34Inspection of Hydraulic/Pneumatic System 34Critical Load Inspection 35Dismantling Inspection 35INSPECTION CHECK LISTS 36Check Category I (Ongoing observation) 37Observe during operation for inadequate performance37Check List Category II (Daily) 37Check List Category III (every 6 months) 38Check List Category IV (every year) 38Wear data criteria 39Bore of Door and Body hinge pins 39Measuring of wear 39Remanufacturing 39Critical Areas 40Trouble shooting 40
6. Size Components 41
Pipe sizes, Slip Segments and Trigger Hammers 42
TAB
LEO
F CO
NTE
NT
SD
ES
CR
IPTIO
NC
OM
MIS
SIO
NIN
GIN
STA
LLA
TION
OP
ER
ATIO
NS
IZE CO
MP
ON
EN
TS
MA
INTE
NA
NC
E&
INS
PEC
TION
DR
AW
ING
S
7
7. DRAWINGS & SPARE PARTS 43
672600-Y Center Latch Elevator 44672000-Y BVC-200 modified for ABVC-200 45Latch opening unit PN: 613860 47PN 613861 Cover Assembly, Middle 50Pneumatic Set WITH FEEDBACKSIGNAL 51PN: 615701-3 Pneumatic Set III 51Elevator Actuation Arrangement 53PN: 615130 For ABVC-200 53Trigger Assembly PN: 672620 55Trigger Unit ABVC 150/200 : PN 671620-1 56Trigger Closing Tool PN: 613700-TCT 58672615 Welding attachment actuator casing 59672652 Welding attachments to elevator 60Spare Parts for one year operation 61Parts list PN: 672600-Y-RSP 61Parts list PN: 672000-Y-RSP 61Parts list PN: 613860-RSP 62Parts list PN: 613861-RSP 62Parts list PN: 615130-RSP 62Parts list PN: 671620-RSP 62Parts list PN: 671620-1-RSP 63
TAB
LEO
F C
ON
TEN
TS
DE
SC
RIP
TIO
NC
OM
MIS
SIO
NIN
GIN
STA
LLA
TIO
NO
PE
RA
TIO
NS
IZE
CO
MP
ON
EN
TS
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
DR
AW
ING
S
8
TAB
LEO
F CO
NTE
NT
SD
ES
CR
IPTIO
NC
OM
MIS
SIO
NIN
GIN
STA
LLA
TION
OP
ER
ATIO
NS
IZE CO
MP
ON
EN
TS
MA
INTE
NA
NC
E&
INS
PEC
TION
DR
AW
ING
S
9
DE
SC
RIP
TIO
N
DESCRIPTION
10
DE
SC
RIP
TION
1. Description
General
The Blohm+Voss ABCV-200 Sliptype elevator is designed to be installed into the links. It is designed for easier operation as the elevator closing sequence can be started automatically. The ABVC-200 Sliptype elevator is rated for 200 short tons. Body and Slips are produced according to API 8C latest edition.The ABVC-200 Sliptype elevator is used for suspending tubular like casing, drill pipe, tubing and drill collars. The VES-indication stands for “Variable Elevator System”, meaning it can accomodate various sizes and types of slips.
Features
• Pneumatic operated elevator• Rapid changing of pipe sizes by means of slips.• Material and manufacturing standard in acc. to API 8C• Pneumatic system is completely integrated and covered into the ABVC-200 Sliptype elevator.• Automated for opening AND closing sequence
Options
PN 613700-TCT Trigger Closing ToolLonger air hoses upon request
Main assembly
The Elevator consist of the following main assemblies:
Latch opening Unit
Elevator Frame
Trigger
Elevator Actuation Arrangement
incl. mech. Indicator System
Main Assembly ABVC-200
11
DE
SC
RIP
TIO
N
Improper / Unsafe Use
The ABVC-200 Sliptype elevator must only be used for the designated purpose. When using the ABVC-200 Sliptype elevator, the load of 200 sh tons must never be exceeded (depending on the rating).
Limited Warranty
The warranty provided will be void if the Elevator is either:a) repaired or serviced by a service facility which was not authorised by Blohm+Voss Repair GmbHb) replacement parts not manufactured by Blohm+Voss Repair GmbH are usedc) modifications were made to the Elevator which were not approved by Blohm+Voss Repair GmbH
Identification
The identification area clearly identifies the Elevator area (manufacturer, type, material, part number, serial number, date of manufacture). It is important to keep this information ready for the purpose of servicing and repair work.
Identification
12
DE
SC
RIP
TION
Technical Data
ACL Type: ABVC-200
Working pressure Min 7 bar (100 Psi), Max 10 bar (145 Psi)
Maximum allowed pressure 10 bar (145 Psi)
Required Volumetric Flow 6,8 m 3/min (240 cfm)
Temperature working range ambient
- 20° C to + 40° C- 4° F to 104° F
Load Capacity 200 sh tons
Part number 672600-Y
API test load 300 sh tons
Pipe Diameter Range
min 2.3/8 inch
max 7.5/8
Weight 1100 kg
B+V Elevator Link 250 sh t
Contents of delivery
Part Number
Hose assembly 613790
Hose coupling 613812
Hose coupling 613811
3/2 way valve 613731
Absorbent 612643
13
DE
SC
RIP
TIO
N
Main Dimensions ABVC-200 Sliptype elevator
B
A
C
D
A = 569 mm
B = 1551 mm
C = 894 mm
D = 931 mm
Main Dimentions ABVC-200
14
DE
SC
RIP
TION
Main components & functioning
Elevator components ABVC
Latch opening Unit
Elevator Frame
Trigger
Elevator Actuation Arrangement
incl. mech. Indicator System
Functioning
The elevator actuating arrangement opens the elevator body pneumatically. When the elevator is open, the drill pipe will be placed in the elevator. When the Trigger system is activated, the elevator actuating arrangement closes. If the elevator is completely closed, the Latch Indicator System shows a green sign in the front. As long as the elevator is not completely closed the Indicator sign indicates red.
ABVC-200 Sliptype-Elevators have exchangeable slips, which allows the elevator to run with different types of pipes and pipe diameters.
Slip system ABVC
Slip system
15
CO
MM
ISIO
NIN
G
COMMISSIONING
16
2. Commissioning
CO
MM
ISIO
NIN
GS
Commissioning ABVC-200 Elevator
Blohm + Voss strongly recommends to accomplish the Elevator commissioning with the Blohm + Voss Commissioning Service.
Read manual before first use !
OK o Check crew is aware of all danger regarding handling the B+V tool.
OK o Go through manual with crew.
Prior to use of the Blohm+Voss Elevator following checks must be carried out :
Scope of supply
OK o Cross check all delivered parts
Pneumatic Characteristics
OK o Operating pressure 7...10 bar (100...145 PSI)
OK o Volumetric flow 6.8 l/min (240 cfm)
OK o Air filter and regulatorLubricated and de-watered, air regulator and lubricator installed
Check and Lubrication
OK o Check elevator is in closed position
OK o Check Air Supply line is disconnected
OK o Check for correct seating of Hinge Pin and latch pin
OK o Apply grease to all greasing points until grease is visibly coming out of the bores
OK o Check if elevator is installed as outlined in manual
OK o OPTIONAL: Connect additional feedback line
OK o Connect the air supply line to the elevator
17
OK o Check elevator opens by air pressure
OK o Check latch indicator shows a red sign when elevator open
OK o OPTIONAL: Check feedback signal indicates elevator open
OK o Switch air pressure off
OK o WARNING: Be careful, stand beside the elevator and follow manual; check if elevator closes by actuating the trigger.
OK o Check if elevator closes after activating trigger.
OK o Check if indicator shows a green sign when elevator is closed
OK o OPTIONAL: Check feedback signal indicates elevator closed
OK o Check required slips are installed before first use
OK o Check if correct size trigger hammer is installed
OK o Check if slip springs are working correctly
OK o Check slip segments are of same size and serial number
OK o Check if slips are fixated correctly
OK o Check all safety / lock wire is present
OK o Check if the trigger lock pin is present
OK o Check elevator opens by air pressure. Now the indicator must indicate red.
OK o Pick up a pipe; Check if, after contact with trigger, the elevator closes and the indicator indicates green
Note: If the elevAtoR Refuses to close, check teNsIoN of tRIGGeR.
Function Test
CO
MM
ISIO
NIN
GS
18
19
INS
TALL
ATI
ON
INSTALLATION
20
INS
TALL
ATIO
N
1
2
3
1R P
A
1
2
3
Elevator ActuatingArrangement
Latch OpeningArrangement
air drain before Elevator closing
actuated when Latchis fully open
3/2 way valve (optional)5
4
3
2
3. Installation
Lifting and transport
WARNING: lIft the Abvc-200 elevAtoR oN the lIftING eARs oNly.WARNING: WeAR youR peRsoNAl pRotectIoN equIpmeNt At All tImes.
Pneumatic functioning
The Three-way-valve (see Pos.5) applies pressure to air operated elevator. The Latch cylinder (Pos.4) will be actuated and causes opening of the latch lock and latch. The Latch will be locked in opening position.
When the latch is fully opened, valve (Pos.3) will be operated by a cam plate. Thereupon the valve (2) will be shifted and the elevator cylinder (1) will be actuated.Then both bodyhalves will open, pretension of the springs will be increased and the trigger system will move into a locked position and keep the frame open. The three-way-valve (Pos.5) has to be operated again and compressed air of the system will exhaust quickly through the valves Pos. 2, 3 and 5.
The Elevator can be attached to the pipe. The Elevator will be closed when a pipe touches the trigger. The Elevator will be latched by the Latch and locked by the Latch Lock. When the elevator is completely closed the Latch Indicator shows a green sign at the front.
Installation of pneumatic Parts
Equip the elevators air supply with a maintenance unit (Lubricator, air regulator, filter) to make sure that devices operate with clean compressed air. An air regulator ensures constant working pressure and guards the pneumatic parts against break down.
Schematic Plan
21
INS
TALL
ATI
ON
Installation of Elevator
Remove the link block bolts and allow the link block assembly to swing open. Place the links in the opened elevator ears, and secure the link block by replacing the removed bolts and safety springs.
WARNING: keep dIstANce fRom the elevAtoR duRING opeRAtIoN ANd tRIAls
Installing and removing the required Slips
A set of slips consists of 3 parts. To equip the elevator with the required slip, the elevator must be open. Before installing a new slip, the seating area in the elevator must be cleaned and lubricated.
WARNING: mAke suRe thAt All 3 slIp seGmeNts ARe the sAme sIze ANd hAve the sAme seRIAl NumbeR.
1. Before fitting the slip-segments, install the correct guide plates.2. First put in the springs. 3. Fit the slip segment on top of the spring. 4. The spring will be compressed and easily slide in the Elevator. 5. Fix the Slip segments with the screw and check if they are properly tightened. 6. Install the safety wire to secure the screws.
WARNING: use the lockING pIN WheN WoRkING oN AN opeN elevAtoR to pReveNt INAdveRtANt closING of the elevAtoR.
WARNING: the Abcv-200 elevAtoR shAll NeveR be used WIthout slIp seGmeNts.
WARNING: Keep distance from the automatic operated Elevator as it may close / open remote operated. Do not work to the Elevator while open. Use the locking Pin.
Locking Pin
22
INS
TALL
ATIO
N
Installation Checklist ABVC-200 Elevator
Basically the Elevator has to be installed as shown in the manual
OK o Make sure the required slips are installed before first use
OK o Make sure the slips are fixed with the screws
OK o Make sure the correct trigger hammer is installed
OK o Make sure the required guide plates are installed
OK o Make sure Pneumatic Pressure is switched on.
Pneumatic Connections
OK o Make sure the controls are connected to the Pneumatic Power Supply
OK o Make sure the 2-hand controls are connected
OK o Make sure the Pneumatic Line is connected
Function test
There are two possibilities to carry out the function test: 1. ABVC-200 Sliptype Elevator standing on the floor 2. ABVC-200 Sliptype Elevator installed into the links
OK o Close elevator
OK o Open elevator
OK o Check signal “elevator closed and latched” is visible (green).
OK o Check signal “elevator open” is visible (red).
OK o Check if closing tool and other loose service tools are removed from the elevator.
23
OP
ER
ATI
ON
S
OPERATIONS
24
OP
ER
ATIO
NS
4. Operations
WARNING: do Not touch the ABVC-200 Sliptype elevAtoR.
WARNING: NeveR opeN the elevAtoR WheN the pIpe loAd Is stIll suspeNded by the elevAtoR.
Safety
• Make sure that ALL pneumatic lines are isolated before any work is carried out in the ABVC-200 Sliptype Elevator. • It is recommended to have the ABVC-200 Sliptype Elevator operated by the driller.
Operation MU (make up)
1. Pick up a section of pipe. The ABVC-200 Elevator is closed when the “elevator closed indication signal” is visible.2. Now make up the stand or joint. 3. When the pipe is made up, pick up the load and open the slips.4. Now lower the string.5. Pick up the weight of the pipe string with the slips, before opening the ABVC- 200 Elevator.
6. Open the ABVC-200 Sliptype Elevator and pick up a new section of pipe.
Operation BO (break out)
1. Pick up the string with the elevator. The ABVC-200 Elevator is closed when the “elevator closed indication signal” is visible.2. Raise the slips. 3. Pull out the string.4. Set the slips5. Release the stringweight from the ABVC-200 Sliptype Elevator.6. Now BO the stand or joint.
7. When the pipe is BO, pick up the stand and handle.
Connecting and disconnecting of the pneumatic hoses
WARNING: be cAReful WheN dIscoNNectING pNeumAtIc hoses. mAke suRe pRessuRe Is of the hoses ANd the WeIGht of the stRING cANNot GeNeRAte pRessuRe.
25
OP
ER
ATI
ON
S
Manual Opening in Case of Emergency
If elevator cannot be opened by compressed air, please follow these points:
1. Disconnect elevator air supply 2. For Latch opening use a steel bar (Pos.1). Be aware of the latch spring!
WARNING: A steel bAR could cAuse INjuRIes due to the lAtch spRING foRce.
3. To open the elevator body remove the two screws (Pos.2) and the Cap (Pos.3).4. Remove the Cotter pin (Pos.4) and unscrew the nut (Pos.5) until the elevator body is fully opened.
After maintenance or repair make sure that the nut (Pos.5) is returned to it`s originally position. Make sure all safety elements and warning signs are in place and undamaged.
23
4
5
Main Assembly
Manual opening in Case of Emergency
26
OP
ER
ATIO
NS
Manual Closing of the Elevator
WARNING: close b+v Acl / ves-Acl elevAtoRs oNly WIth help of the b+v tRIGGeR closING tool pN 613700-tct (optIoNAl).
Remove Trigger Closing Tool from Elevator after every time of use.
WARNING: NeveR use tools lIke hAmmeRs oR bARs to close ABVC-200 Sliptype elevAtoRs. use AlWAys the b+v tRIGGeR closING tool to close the elevAtoRs
Handling the Trigger Closing Tool
• Elevator is hanging free, just above drill floor• Make sure the Trigger Locking Pin is removed
First example of wrong closing method
Second example of wrong closing method
Trigger Closing Tool
27
OP
ER
ATI
ON
S
Depending to different Hammer sizes:
• Turn back Spindle to maximum opening measure of Trigger Closing Tool first.• Put the Trigger Closing Tool on top of the Trigger System as shown below.
Turning the screw adjusts the Trigger Closing Tool , so there is no space in front to the hammer and no space to the rear of Trigger System.
WARNING: It Is dANGeRous ARouNd the lAtch AReA: No peRsoNNel oR objects AlloWed
Release air pressure from the Elevator.
Adjust to fit
Position of Locking Pin
Scetch of TCT
28
OP
ER
ATIO
NS
Hold down the Trigger Closing Tool with one hand Use the wrench with the other hand
By turning the screw the Hammer of Trigger System is slowly drawn backwards.
WARNING: WhIle tuRNING the scReW double check thAt Nobody Is IN fRoNt of the elevAtoR !
The elevator will close suddenly and quick after a few turns of the screw. There isan extreme danger of injuries.
Remove Trigger Closing Tool from Elevator after every time of use.
How to close the Elevator
Keep distance while working on the TCT
Elevator in closed position
29
OP
ER
ATI
ON
S
Trigger Closing Tool must be taken off the Elevator after every time of use.
Example of Elevator without TCT
30
OP
ER
ATIO
NS
31
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
MAINTENANCE& INSPECTION
32
MA
INTE
NA
NC
E &
INS
PEC
TION
General
If cracks, excessive wear etc. is recognised, contact Blohm + Voss Repair GmbH or an authorised service company.Weldings of the castings should be done only by Blohm + Voss Repair GmbH or an authorised service company in according to Blohm+Voss welding procedure.
A regular preventative maintenance program should be established for all elevators. These written maintenance procedures should be given to the crew or maintenance personnel.
WARNING: foR seRvIce ANd mAINteNANce dIscoNNect the AIR supply. WhIle WoRkING At the opeN elevAtoR, the tRIGGeR hAs to be IN the locked posItIoN.
Daily Lubrication
Lubricate Hinge Pins and Latch Pins (Grease Nipples).Lubricate Springs and Trigger System. Lubricate Emergency Opening and Actuator.
Daily Inspection
Inspect visually the Latch Opening Arrangements and Actuator with springs.
Grease points
Grease point 1: Hinge PinGrease point 2: Trigger LeverGrease point 3: TriggerGrease point 4: Latch PinGrease point 5: Bearing PinGrease point 6: Elevator Hinge
Daily Test
The Function of the Feedbacksignal has to be checked daily. If any damage or malfunction were found, take the elevator out of service for repair.
Locking of screws
All Screws are normally secured by a mechanical bolt lock or with a safety wire. All other screws are secured by metal adhesive (Locktite).
5. Maintenance and Inspection
1
3
2
4
6
5
Position of Locking Pin
Greasing Points
33
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
Grease Quality
In order to achieve efficient greasing even at different environmental temperatures, we recommend the following grease types should be used (obtainable from Blohm + Voss Oil Tools): • Low-Viscosity grease• Type AVIATICON Grease XRF
Alternatively; Use EP1 gear lubricating grease for greasing ”non-oil tight gear trains” when temp. < 0°C/32°F.Use EP2 when temp. > 0°C/32°F.
WARNING: eNsuRe to WeAR peRsoNAl sAfety pRotectIoN lIke Gloves ANd sAfety GlAsses WheN hANdlING hydRAulIc oIl ANd/oR GReAse. oIl ANd GReAse mAy be poteNtIAlly hARmfull foR skIN ANd eyes.
Recommended grease gun
34
MA
INTE
NA
NC
E &
INS
PEC
TION
Category IThis category involves observing the equipment during operation for indications of inadequate performance.When in use, equipment shall be visually inspected on a daily basis for cracks, loose fits or connections, elongation of part, and other signs of wear, corrosion or overloading. Any parts found to show cracks, excessive wear, etc., shall be removed from service for further examination.The equipment shall be visually inspected by a person knowledgeable in that equipment and its function.
Category IIThis is Category I inspection plus further inspection for corrosion, deformation, loose or missing components, deterioration, proper lubrication, visible external cracks, and adjustment. Category II may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances.
Category IIIThis is Category II inspection plus further inspection, which should include NDT of critical areas and may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances.Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paint-stripping, steam-cleaning, grit-blasting).
Category IVThis is Category III inspection plus further inspection for which the equipment is disassembled to the extent necessary to conduct NDT of all primary-load-carrying components.
Equipment shall be:• disassembled in a suitable-
equipped facility to the extent necessary to permit full inspection of all primary-load-carrying components and other components that are critical to the equipment.
• inspected for excessive wear, cracks, flaws and deformation.
Procedure:• Corrections shall be made
in accordance with the manufacturer’s recommendations.
• Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paint-stripping, steam-cleaning, grit-blasting)
Frequency
Periodic inspection
The recommended schedule for inspection of all kind of • Elevators:Ongoing IDaily: II6 Monthly: III1 Year: IV
The recommended frequencies apply for equipment in use during the specified period.The inspection frequencies are only recommendations. The schedule of inspection heavily depends on the following factors:• environment• load cycles• regulatory requirements• operating time• testing• repairs• re manufacture
Non-periodic inspection
A complete, on-job, shut-down inspection equivalent to the periodical Category III or Category IV should be made before (if anticipated) and after critical jobs (e.g., running heavy casing / drill strings, jarring, pulling on stuck pipes and/or operating at extreme low temperatures) <-20° C (<-4° F).
Inspection
A thorough inspection should be carried out periodically (every 3 months) or as special circumstances may require. Before starting an inspection disconnect any hydraulic/pneumatic system and remove all foreign materials (dirt, paint, grease Oil, scale, etc.) from surface by a suitable method. After a field inspection, it is advisable to record the extent of testing and testing results. Conduct the periodic or critical load inspection in the field by the crew with the supervisor. If cracks, excessive wear etc. is recognized, contact Blohm + Voss Oil Tools or an authorized service company.
Inspection of Hydraulic/Pneumatic System
Check for leakage every day. Should internal or external leakage reach an unacceptable high level, contact Blohm + Voss Oil Tools or an authorized service company.
Inspection categories acc. to API RP 8B
35
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
Critical Load Inspection
Critical loads may occur. For example: impact loads such as jarring, pulling on stuck pipe, etc. If critical loads occurred unexpectedly, conduct the inspection immediately.
Dismantling Inspection
Generally, when the equipment returns to base, warehouse, etc. Carry out the Tool inspection, immediately. Furthermore, control it prior to its being sent on the next job. • The Tool should be dismantled and
inspected in a suitably equipped facility for excessive wear, cracks, flaws or deformations.
• Corrections should be made in accordance with recommendations which can be obtained from Blohm + Voss Oil Tools.
• Weldings at the castings should be done only by Blohm + Voss Oil Tools or an authorized service company in according to Blohm+Voss welding procedure.
• When need is shown in a field inspection, dismantle the Tool and arrange an inspection in a suitably equipped facility.
• Springs should be carefully visually inspected for excessive wear and obvious weakness.
36
MA
INTE
NA
NC
E &
INS
PEC
TION
INSPECTION CHECK LISTS
CHECK LIST FRONT PAGE
TYPE OF EQUIPMENT
SERIAL NUMBER
PART NUMBER
SUPERVISOR
DATE OF INSPECTION
INSPECTION CATEGORY
PLACE OF INSPECTION
37
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
Check Category I (Ongoing observation)
Observe during operation for inadequate performance
Check List Category II (Daily)
CHECK FOR THE FOLLOWING GENERAL ISSUES (but not limited to):
DESCRIPTION CHECKED SIGNATURE
1 Complete front page of check list for the records OK
2 Check for correct size of elevator or slip segments OK
3Check correct function elevator latch indicator (open - red- or closed - green-)
OK
4 Check function of feedback signal (elevator closed) OK
5 Check state of lubrication OK
6 Check functioning of elevator as a whole OK
Remarks
CHECK FOR LOOSE ITEMS, ESPECIALLY FOR (but not limited to):
DESCRIPTION CHECKED SIGNATURE
1 Hinge pins, bolts and retainers OK
2 Fixation of slip segments OK
3 Screws, bolts, nuts, washers, retainers, springs and lock wire OK
4 Trigger hammer OK
5 Link blocks OK
6 Check completeness and condition of warning plates and labels OK
Remarks
CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR (but not limited to):
DESCRIPTION CHECKED SIGNATURE
1 Elevator Body and Door OK
2 Hing pins, bolts, nuts OK
3 Slip segments OK
4 Latch and lug OK
5 Closing arrangement OK
6 Trigger arrangement OK
Remarks
PNEUMATIC
DESCRIPTION CHECKED SIGNATURE
1 Check for loose fittings, pipes, valves OK
2 Check for pneumatic leaks (hoses, valves and cylinders) OK
3 Check condition of pneumatic couplings and connection hoses OK
Remarks
_________________________________ _______________________________SUPERVISOR DATE
38
MA
INTE
NA
NC
E &
INS
PEC
TION
Check List Category III (every 6 months)
GENERALDESCRIPTION CHECKED SIGNATURE1 Carry out an Category II inspection OK2 NDT (MPI) critical areas. Some disassembly may be needed to do so OK
3 Check parts for wear according to allowable tolerances. OK
Remarks
_________________________________ ________________________SUPERVISOR DATE
Check List Category IV (every year)
GENERALDESCRIPTION CHECKED SIGNATURE1 Carry out an Category III inspection OK
2NDT (MPI) critical areas and load bearing components. Strip elevator to do so
OK
3 Change all pneumatic hoses and fittings OK
4 Check condition of pneumatic valves and replace if necessary OK
Remarks
39
MA
INTE
NA
NC
E&
IN
SP
ECTI
ON
Wear data criteria
Bore of Door and Body hinge pins
Bore Body Hinge Pin
Dimension new max: 70.074 mmDimension worn max: 70.524 mm
Bore Door Hinge Pin
Dimension new max: 16.043 mmDimension worn max: 16.603 mm
Measuring of wear
To measure link ears it is necessary to use calipers and a ruler. Significant wear is restricted to the top link ear, it is here that the measurement is taken.Hinge Pins, Latch Pins and socket holes are not normally measured for wear in the field. When it becomes apparent that the Hinge or Latch Pins have more tolerances, the elevator should be dismantled for general engineering check up.
Remanufacturing
Remanufacturing and repair of critical areas or load bearing parts must be done only by B+V or an B+V authorized service company.Also minor cracks or defects, which may be removed by grinding without reducing safety or operation of the elevator, must be done only by B+V or an B+V authorized service company.Following the repair, the parts should again be inspected by an appropriate method to insure that the defect has been completely removed.If the elevator is defective beyond repair, destroy it directly. If it should turn out necessary to secure the open elevator for repair work, inspection, etc., fix the trigger with the locking pin after opening of the elevator.
40
MA
INTE
NA
NC
E &
INS
PEC
TION
Trouble shooting
Elevator does not open• Checkconnectionfordamages• Checkpneumaticpressureand flow rate• Checkfunctionandadjustmentof control valve• CheckfunctionofValve(3)(see Pneumatic diagram)Elevator does not close complete• CheckLatchandLatchLock Springs for damage• CheckpneumaticSystemfor damages
Critical Areas
Critical Areasare striped
Critical area's are hatched
Critical Areas
41
SIZ
E C
OM
PO
NE
NT
S
SIZE COMPONENTS
42
SiI
ZE C
OM
PO
NE
NT
S
6. Pipe sizes, Slip Segments and Trigger Hammers
Slips and Hammers
Pipe dimension
Trigger Hammers Slip Segments
23/8” 613835-4 672172
27/8”
27/8”
613835-4613835-4
672173
31/2”
31/2”
613835-1613835-1
672134672134
4” 4” 41/
2”
613835-2613835-2613835-2
672135672135672136
41/2”
5” 51/
2”
613835-3613835-3613835-3
672136672137672138
57/8”
65/8”
6.906
613835-3613835-5613835-5
613902-115672139672139
7” on request 672140
73/4 ” on request 672176
75/8 ” on request 672175
Note: ( - ) Trigger Hammers without Partnumbers will be manufactured on special request.
Slips
43
DR
AW
ING
S&
SP
AR
E P
AR
TS
DRAWINGS& SPARE PARTS
44
DR
AW
ING
S&
SP
AR
E PA
RT
S
672600-Y Center Latch Elevator
Pos. Qty Part. No. Description
1 1 672000-Y Elevator Assembly BVC200
2 1 613860 Latch Opening Unit
3 1 615130 Elevator Actuation Arrangement
4 1 672620 Trigger Assembly
5 1 672615 Welding Attachement Actuator Casing
6 1 672652 Welding Attachments
7 1 672006-1 Spring
8 1 615003-2 Lach Lock Assembly
9 1 672657 Hook for ABVC 200
10 1 671056 Safety Wire
11 2 672683 Hose Assembly
12 1 613790 Hose Assembly
13 1 613733 Stop and Go Valve
Parts list PN: 672600-Y
1
2
4 35
6
7
8 9
10
11
12
45
DR
AW
ING
S&
SP
AR
E P
AR
TS
Parts list PN: 672000-Y BVC-200
Pos. Qty Part no. Description
1 1 672001-1 Elevator Frame 1
2 1 672001-2 Elevator Frame 2
3 1 672023 Latch
4 1 615003-2 Latch Lock Assembly
5 1 641030 Latch Lock Pin
6 1 672006-1 Latch Spring for ABVC 200
7 1 612507 Latch Lock Spring
8 1 615024 Rivet Pin
9 1 615016 Door Lug Pin
10 1 612509 Latch Pin Securing Ring
11 2 612512 Link Block
12 1 672510 Hinge Pin Assembly
13 2 622514 Clevis Pin with Head
14 2 622515 Safety Spring
15 2 613623-1 Screw
16 2 752338 Castle Nut
17 4 752339 Cotter Pin
18 4 672116 Slip Bolt
19 4 672015 Slip Spring
20 4 672117 Screw
21 1 672510-1 Latch Pin Assembly
22 4 672053 Serrated Lock Washer
672000-Y BVC-200 modified for ABVC-200
21.1
12.1
8
5
3
76
4 10
21.5
21.2
21.3
21.4
9 19
22
18
1
2
20
14 16 11 13
1517
12.4
12.3
12.2
12.5
2112
46
DR
AW
ING
S&
SP
AR
E PA
RT
S
Parts list PN: 672510 Hinge Pin Assembly
Pos. Qty Part. No. Description
1 1 671511 Hinge Pin
2 1 671575 Securing Plate for Hinge Pin
3 2 613825 Safety Sheet
4 2 613823 Screw
5 2 612515 Grease Nipple
Parts list PN: 672510-1 Latch Pin Assembly
Pos. Qty Part. No. Description
1 1 671511-1 Latch Pin
2 1 671575 Securing Plate for Hinge Pin
3 2 613825 Safety Sheet
4 2 613823 Screw
5 2 612515 Grease Nipple
47
DR
AW
ING
S&
SP
AR
E P
AR
TS
Latch opening unit PN: 613860
1312
67
57 56
13 66 55 5761
65
6235
33
643937
33
5754
15
41 42 4043 33
36 44
19 17
10
30 18 19 20 11 25 22
14 9
2110
26 2329
24
38
3532
14
52 51 49 50
628
48
58 25 11
53
4645
7 8
4727
31
57
63
35
48
DR
AW
ING
S&
SP
AR
E PA
RT
S
Parts list PN: 613860 Latch Opening Unit
Pos. Qty Part. No. Description
6 2 613889 Clevis Pin with Head
7 2 613890 Washer
8 2 70814 Cotter Pin
9 1 613862 Casing Latch opening system
10 7 621412 Screw
11 2 612685 Permaglide Bush
12 7 752312 Lock Nut
13 1 621427 Screw
14 1 621430-1 Nut
15 1 613891 Clevis Pin with Head
17 1 612515 Grease Nipple
18 1 613880 Spring
19 4 615879 Washer
20 1 611009 Cotter Pin
21 1 613870 Lever
22 1 613881 Bolt
23 1 613882 Bolt
24 2 612509 Latch Pin Securing Ring
25 2 613879 Pin
26 1 613871 Yoke
27 2 613885 Spiral Split Pin
28 1 612641 Latch Cylinder
29 2 643775-1 Screw
30 2 775089 Screw
31 1 612662-1 Double Socket
32 1 612663-1 Socket
33 3 645096 L-Adapter
35 5 612944 Straight Connection
36 2 613945-1 Seal Rings
37 1 755737 Equal Tee
38 1 613797 Pneumatic Hose Assembly, L=290mm
39 1 613793 Pneumatic Hose Assembly, L=360mm
40 1 613886 3/2-Way-Valve
41 3 613887 Screw
42 3 613883 Washer
43 1 612661 Absorber II
44 1 645111 Adapter
45 4 613580 Rope Clamp I
46 8 613884 Cylinder Head Screw
47 1 612574 Rope
48 1 613878 Angle position indicator switch
49 2 645028 Screw
50 2 645683 Washer
51 1 645195 Screw
49
DR
AW
ING
S&
SP
AR
E P
AR
TS
Parts list PN: 613860 Latch Opening Unit
Pos. Qty Part. No. Description
52 2 645675 Nut
53 1 613861 Cover Assembly, middle
54 1 752117 Cover Plate
55 1 613868 Cover, left
56 1 613869 Cover, left behind
57 24 613899 Screw
58 1 612688 Spring
59 - - -
60 - 615701-3 Pneumatic Set III
61 3 613944 Reducing Nipple
62 1 612642-1 Quick Relief Valve
63 2 755370 Straight Bulkhead Coupling
64 1 613798 Pneumatic Hose Assembly 590 mm
65 1 613794 Pneumatic Hose Assembly 410 mm
66 2 755372 Standpipe Reducer
67 6 621431 Washer
50
DR
AW
ING
S&
SP
AR
E PA
RT
S
PN 613861 Cover Assembly, Middle
Parts list PN: 613861 Cover Assembly, Middle
Pos. Qty Part. No. Description
1 1 613863 Cover, middle
2 1 613864 Indicator Disk
3 1 613865 Lever
4 1 613866 Holder for Indicator Disk
5 7 753047 Washer
6 2 613893 Cotter Pin
7 2 613894 Screw
8 2 645683 Washer
9 2 613895 Cotter Pin
10 1 613896 Tension Spring 1
11 1 613897 Tension Spring 2
12 - - -
13 1 643779-1 Screw
14 1 612574 Rope
1
2
3
4
6
6
5
57
5
8
8
8
9
9
10
9
11
13
14
51
DR
AW
ING
S&
SP
AR
E P
AR
TS
Pneumatic Set WITH FEEDBACKSIGNAL
PN: 615701-3 Pneumatic Set III
1
2 3
8
10
9
27 8 12
12 1412
212221202337
2
3
1R P
A
8
11
1
2
3
9
19
28
13
31
15
18
17
Elevator ActuatingArrangement
Latch OpeningArrangement
34
19
1918
32
30
28
32
16
32
33 17
19
4
6
5
9 10
18
30
36
36
32
34
52
DR
AW
ING
S&
SP
AR
E PA
RT
S
Parts list PN: 615701-3 Pneumatic Set III
Pos. Qty Part no. Description
1 1 615160 Elevator Cylinder
2 1 615128 Reducing Fitting
3 1 612647-1 Swivel Connection
4 1 645111 Adapter
5 1 613830 Distribubtion Block
6 1 645094 Plug
7 - - -
8 3 612662-1 Double Socket
9 3 612663-1 Socket
10 2 613945 Swivelling Screw Fitting
11 1 612641 Latch Cylinder
12 3 613944 Reducing Nipple
13 1 612661 Absorber II
14 1 612642-1 Quick-Relief-Valve
15 1 613886 3/2-Way-Valve
16 1 755737 Equal Tee
17 2 755370 Straight Bulkhead Coupling
18 3 645096 L-Adapter
19 4 612944 Straight Connection
20 1 612655 Cover-Piece
21 2 612654 Straight-Socket
22 1 612653 EO-Pipe
23 2 613812 Clutch Hose Coupling
24 - - -
25 - - -
26 - - -
27 1 612654 Straight-Socket
28 2 613945-1 Seal Rings
29 - - -
30 2 613787 Pneumatic Hose 400mm
31 1 613788 Pneumatic Hose 250mm
32 3 613789 Pneumatic Hose 450mm
33 1 613790 Pneumatic Hose 5000 mm
34 1 613792 Pneumatic Hose 150mm
35 2 613791 Pneumatic Hose 900mm
36 4 755372 Standpipe Reducer
37 1 613790 Stop and Gio Valve Assembly
53
DR
AW
ING
S&
SP
AR
E P
AR
TS
Elevator Actuation Arrangement
PN: 615130 For ABVC-200
12
7
11
14
15
1619
25
26
31
32
3536
37
3839
40
48
42
44
45
41
43
8
49
464733
34 34
20
20
20 20
2020
20
20
17
5 10
24
30
2949
49
5
5
24
30
3011
11
11
8
17
15
14
19
1841
2819
13 27
50
54
DR
AW
ING
S&
SP
AR
E PA
RT
S
Parts list PN: 615130 Elevator Actuation Arrangement
Pos. Qty Part. No. Description
1 1 615131 Actuator Casing
2 1 615132 Actuator
3, 4 n/a
5 3 615134 Connection bar
6 na
7 2 615137 Spring support
8 2 615138 Spring support II
9 4 615133 Rod
10 1 615136 Bolt
11 2 615135 Actuating Pin I
12 na
13 1 613623 Castle nut
14 4 615141 Pressure Spring
15 4 615143 Pressure Spring
16 1 613690 Double Plate
17 6 612690 Hexagon nut
18 3 612692 Cylinder Head Screw
19 4 615145 Cylinder Head Screw
20 12 615146 Cylinder Head Screw
21, 22, 23 na
24 4 615147 Cotter pin
25 1 615140 Cover
26 1 615139 Cap
27 1 612679 Washer
28 2 613640 Cylinder head scew
29 1 615134 Connection bar
30 3 615136 Bolt
31 1 615160 Elevator cylinder
32 1 615831 Pneumatic cap
33 2 613782 Hexagon head screw
34 2 752124 Lock washer
35 1 612647-1 Swivel connection
36 1 612648 EO-pipe band
37 2 612644 Hose clip
38 1 612668 Air hose II
39 1 612658 Pipe socket
40 1 615704 Distribution block
41 2 612654 Straight socket
42 1 612653 EO-pipe
43 1 612655 Cover Piece
44 1 613812 Clutch hose coupling
45 1 615128 Reducing Fitting
46 2 612702 Double socket
47 2 615703 Socket
48 1 613785 Cylinder head scew
49 4 612650 Screw
50 1 752322 Cotter pin
55
DR
AW
ING
S&
SP
AR
E P
AR
TS
Trigger Assembly PN: 672620
2
1
3
Parts list PN: 672620
Pos. Quantity Part no. Description
1 1 671620-1 Trigger Unit
2 1 672622-... Hammer
3 3 672616 Mounting Grame
56
DR
AW
ING
S&
SP
AR
E PA
RT
S
Trigger Unit ABVC 150/200 : PN 671620-1
10
6 17 11
3
22 9
1516
4
21
2
20 10
14
5
8
17 1819176
13 12
20
57
DR
AW
ING
S&
SP
AR
E P
AR
TS
Parts list PN: 671620-1
Pos. Quantity Part no. Description
1 1 613839 Trigger Casing
2 1 671621 Slide
3 1 671623 Lever left
4 1 671623-1 Lever right
5 1 613834 Spindle
6 9 613823 Screw
7 4 613824 Taper Pin
8 1 613626 Spring
9 1 613841-1 Bolt Assembly for Hammer
10 2 613840 Bolt
11 2 613837 Bolt
12 1 752330 Castle Nut
13 1 752331 Cotter Pin
14 1 620411 Spring Type Straight Pin
15 2 612509 Latch Pin Securing Ring
16 4 613720 Retaining Ring
17 9 613825 Washer
18 2 612515 Grease Nipple
19 4 613826 Thread Pin
20 2 70064 Grease Fitting
21 1 613842 Safety Pin
22 4 612594 Sliding Bushing
58
DR
AW
ING
S&
SP
AR
E PA
RT
S
Trigger Closing Tool PN: 613700-TCT
Parts list PN: 613700-TCT
Pos. Quantity Part no. Description
1 1 613735 Body
2 1 613735-1 Center Support
3 1 613735-2 Hexagon head screw
4 1 621435 Washer
5 1 752837 Cotter Pin
6 1 613735-3 Hexagonal Nut
7 1 775015-2 Threaded Pin
PN 613888 Steel bar for Latch opening
13
42
5
67
59
DR
AW
ING
S&
SP
AR
E P
AR
TS
672615 Welding attachment actuator casing
Pos. Qty Part. No. Description
1 1 672615-1 Upper Bushing
2 1 672615-2 Lower Bushing
1
2
Parts list PN: 672615
60
DR
AW
ING
S&
SP
AR
E PA
RT
S
Pos. Qty Part. No. Description
1 1 672653 Upper flange
2 1 672654 Lower flange
3 1 671605 Link block right
4 1 671604 Link block left
5 1 672610 Upper eye plate door
6 1 672611 Upper eye plate body
7 1 672612 Lower eye plate door
8 1 672613 Lower eye plate body
9 1 672614 Knaggen
672652 Welding attachments to elevator
Parts list PN: 672652
1
2
78 10 56 34 9
61
DR
AW
ING
S&
SP
AR
E P
AR
TS
Spare Parts for one year operation
Parts list PN: 672600-Y-RSPPos. Quantity Part no. Description
1 2 613791 Hose Assembly
2 1 671637 Warning sign ”Spring”
3 1 671638 Warning sign ”Blohm+Voss”
4 1 671639 Warning sign ”Automatic”
5 1 671640 Warning sign ”Hands”
6 1 671642 Warning sign “Grease Daily”
7 1 672657 Hook for ABVC 200
8 1 671056 Safety Wire
9 1 613790 Hose Assembly
10 1 613733 Stop and Go Valve
Parts list PN: 672000-Y-RSP
Pos. Qty Part no. Description
4 0 615003 Latch Lock
5 1 641030 Latch Lock Pin
6 0 672006 Latch Spring
7 1 612507 Latch Lock Spring
10 1 612509 Latch Pin Securing Ring
12.2 1 671575 Securing Plate for Hinge Pin
12.3 2 613823 Safety Sheet
12.4 2 613825 Screw
12.5 2 612515 Grease Nipple
13 2 622514 Clevis Pin with Head
14 2 622515 Safety Spring
15 2 613623-1 Srew
16 2 752338 Castle Nut
17 4 752339 Cotter Pin
18 4 672116 Slip Bolt
19 4 672015 Slip Spring
20 4 672117 Screw
21.2 1 671575 Securing Plate for Hinge Pin
21.3 2 613823 Safety Sheet
21.4 2 613825 Screw
21.5 2 612515 Grease Nipple
22 4 672053 serrated Lock Washer
62
DR
AW
ING
S&
SP
AR
E PA
RT
S
Parts list PN: 615130-RSP
Pos. Quantity Part no. Description
26 1 615139 Cap
28 2 613640 Cylinder Head Screw
32 1 615831 Pneumatic Cap
33 2 613782 Hexagon Head Screw
34 2 752124 Lock Washer
46 2 615702 Double Socket
47 2 615703 Socket
48 1 613785 Cylinder Head Screw
Attention:Inside the Elevator Actuation Unit is assembled with heavy springs under high pressure !There is an extreme danger of injuries while disassembling, ifdisassembling is not done correctly. Therefore disassembling and repair is strictly permitted only for Blohm + Voss and their authorizied Service Facilities.
Parts list PN: 671620-RSP
Pos. Quantity Part no. Description
2 1 672622-0 Hammer for 2.3/8“-2.7/8“
2 1 672622-1 Hammer for 4.1/2“-5.1/2“
2 1 672622-2 Hammer for 5.5/8“-7.5/8“
Parts list PN: 613861-RSP
Pos. Quantity Part no. Description
1 1 613863 Cover, middle
10 1 613896 Tension Spring 1
11 1 613897 Tension Spring 2
14 1 613898 Rope
As an alternative to the single spare parts the hole Latch opening unit ( PN 613860) can be ordered completely.
Parts list PN: 613860-RSP
Pos. Quantity Part no. Description
40 1 613886 3/2-Way-Valve
62 1 612642-1 Quick Relif Valve
As an alternative to the single spare parts the hole Latch opening unit ( PN 613860) can be ordered completely.
63
DR
AW
ING
S&
SP
AR
E P
AR
TS
Parts list PN: 671620-1-RSP
Pos. Quantity Part no. Description
3 1 671623 Lever left
4 1 671623-1 Lever right
7 9 613823 Screw
8 4 613824 Taper Pin
10 1 613841-1 Bolt Assembly for Hammer
11 2 613840 Bolt
12 2 613837 Bolt
16 2 612509 Latch Pin Securing Ring
17 4 613720 Retaining Ring
18 9 613825 Washer
19 2 612515 Grease Nipple
20 4 613826 Thread Pin
21 4 612594 Sliding Bushing
25 2 70064 Grease Fitting