1 5471 (supersedes 5431)---0506---J7 RTC---80100 II Link-Belt Cranes Technical Dat a Specifications & Capacities Telescopic Boom Rough Terrain Crane 100 ton (90.72 metric ton) CAUTION: This material is supplied for reference use only. Operator must refer to in---cab Crane Rating Manual and Operator’s Manual to determine allowable crane lifting capacities and assembly and operating procedures.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
15471 (supersedes 5431)---0506---J7
RTC---80100 IILink-Belt Cranes
Technical DataSpecifications & Capacities
Telescopic Boom Rough Terrain Crane100 ton (90.72 metric ton)
CAUTION: This material is supplied forreference use only. Operator must refer toin---cab Crane RatingManual andOperator’sManual to determine allowable crane liftingcapacities and assembly and operatingprocedures.
Boom, Attachments, and Upper StructureJ BoomDesign --- Five section, formed construction of extra hightensile steel consisting of one base section and four tele-scoping sections. The first telescoping section extendsindependently by means of one, double---acting, singlestage hydraulic cylinder with integral holding valves. Thesecond telescoping section extends independently bymeans of one, double---acting, single stage hydraulic cylin-der with integral holding valves. The third and fourth sec-tions extend proportionally by means of one, double---act-ing, single stage cylinder with integrated holding valvesand cables.
BoomS 40---150 ft (12.2 ---45.7m) five section full power boomS Three boom extend modes, controlled from the opera-tor’s cab, provide superior capacities by varying the ex-tension of the telescoping sections:S Standard mode is the full power, synchronized modeof telescoping all sections proportionally
S A---max1mode (or mode ‘A1’) extends only the innerand center sections to 95 ft (29m) offering increasedcapacities for in---close, maximum capacity picks
S A---max2mode (or mode ‘A2’) tip, outer and center sec-tions extend to 122.5 ft (37.34m) offering maximumstability
S Mechanical boom angle indicatorS Maximum tip height for each extend mode is:S Standard is 159 ft 6 in (48.6m).S A---max2 is 132 ft 6 in (40.3m)S A---max1 is 105 ft 6 in (32.1m)Boom Wear PadsS Bottom wear pads are universal for all boom sectionsS Top wear pads are universal for all boom sectionsBoom HeadS Six 16.5 in (41.9cm) root diameter nylon sheaves to han-dle up to twelve parts of line
S Easily removable wire rope guardsS Rope dead end lugs on each side of the boom headS Boom head is designed for quick---reeve of the hookblockBoom ElevationS One double acting hydraulic cylinder with integral hold-ing valve
S Boom elevation: ---3˚ to 80˚Auxiliary Lifting Sheave --- OptionalS Single 16.5 in (41.9m) root diameter nylon sheaveS Easily removable wire rope guardsS Does not affect erection of the fly or use of the main headsheaves
Hook Blocks and Balls --- OptionalS 100 ton (90.72mt) 6 sheave, quick---reeve hook block, withsafety latch
S 80 ton (72.57mt) 5 sheave, quick---reeve hook block withsafety latch
S 50 ton (45.36mt) 4 sheave, quick---reeve hook block withsafety latch
S 12 ton (10.89mt) hook ball (swivel) with safety latchFly --- OptionalS 31 ft---55 ft (9.45---16.76m) two piece bi---fold lattice fly,stowable, offsettable to 2˚, 25˚, and 45˚. Maximum tipheight for 31 ft (9.45m) fly is 190 ft (57.9m) and for the 55 ft(16.76m) is 214 ft (65.2m).Fly Extensions --- OptionalS One 15 ft (4.57m) lattice extension to be mounted be-tween the 31 ft (9.45m) and 55 ft (16.76m) fly options.Maximum tip height is 228 ft 6 in (69.6m).
J Operator’s Cab and ControlsEnvironmental Cab --- Fully enclosed, one person cab ofgalvaneal steel structure with acoustical insulationEquipped with:S Tinted and tempered glass windowsS Extra---large fixed front window with windshield wiper andwasher
S Swing up roof window with windshield wiperS Sliding left side door with large fixed windowS Sliding rear and right side windows for ventilationS Six way adjustable, cushioned seat with seat belt andstorage compartment
S Engine dependent warm---water heater with air ducts forfront windshield defroster and cab floor
S Defroster fan for the front windowS Bubble levelS Circulating fanS Adjustable sun visorS Dome lightS Cup holderS Fire extinguisherS Left side viewing mirrorS Two position travel swing lockAir Conditioning --- Optional --- Integral with cab heatingsystem utilizing the same ventilation outletsSteering Column --- Pedestal type with tilt and telescopefunctions for operator comfort. Column includes the follow-ing controls and indicators:Left and right levers include:
S Horn buttonS Turn signal switchS Driving light switchS Forward/Neutral/Reverse direction switch
S Travel circuit temperatureS Engine oil pressureS Travel park brakeS Service brakeS Turn signalsS Case filter restrictionS Charge filter restrictionS Pump CPU errorS Engine overspeedS Rear wheel offset---optionalS Emergency steer --- optionalArmrest Controls --- Two dual axis hydraulic joystick con-trollers or optional single axis hydraulic controllers for:S SwingS Boom hoistS Main rear winchS Auxiliary front winch --- optionalS Drum rotation indicationS Drum rotation indicator activation switchS Winch high/low speed and disable switch(es)S Third wrap selector switch --- optionalS Telescopic override switchesS Warning horn buttonS Swing park brakeOutrigger Controls --- Hand held control box with umbilicalcord gives the operator the freedom to view operation whilesetting the outriggers.Foot ControlsS Boom telescopeS Swing brakeS Engine throttleS Service brakeRight Front Console --- Controls and indicators for:S Engine ignition S Console dimmer switchS Engine throttle lock S Bubble levelS Function disable S 12 volt power connectionS Fine metering S Air conditioning --- optionalS Front windshield wiper S Boom floodlight --- optionaland washer S Rotating beacon/Strobe
S Cab floodlights light --- optionalS Warning horn S Third wrap indicator ---S Heating controls optionalCab Instrumentation --- Ergonomically positioned, analoginstrumentation for crane operation including:S Engine coolant temperature with warning indicatorS Hydraulic oil temperature with warning indicatorS Fuel level with warning indicatorS TachometerS Travel circuit temperature with warning indicatorS Voltmeter with warning indicator
Rated Capacity Limiter --- Microguard graphic audio---visual warning system integrated into the dash with anti ---two block and function limiter. Operating data availableincludes:S Crane configurationS Boom length and angleS Boom head heightS Allowed load and % of allowed loadS Boom angleS Radius of loadS Actual loadS Operator settable alarms (include):S Maximum and minimum boom anglesS Maximum tip heightS Maximum boom lengthS Swing left/right positionsS Operator defined area (imaginary plane)
S Two 15 ft (4.57m) lattice extension to be mounted be-tween the 31 ft (9.45m) and 55 ft (16.76m) fly options.Maximum tip height is 243 ft (74.07m).Internal RCL Light Bar --- Optional --- Visually informs theoperator when crane is approaching maximum load capac-ity with a series of green, yellow, and red lights.External RCL Light Bar --- Optional --- Visually informs theground crew when crane is approaching maximum loadcapacity with a series of green, yellow, and red lights.
J SwingMotor/Planetary --- Bi ---directional hydraulic swing motormounted to a planetary reducer for 360˚ continuoussmooth swing at 1.5 rpm.Swing Park Brake --- 360˚, electric over hydraulic, (springapplied/hydraulic released) multi ---disc brake mounted onthe speed reducer. Operated by a toggle switch from theoperator’s cab.Swing Brake --- 360˚, foot operated, hydraulic applied discbrake mounted to the speed reducer.Swing Lock --- Two---position swing lock (boom over frontor rear) operated from the operator’s cab.360˚ Positive Swing Lock --- Optional --- Meets New YorkCity requirement.
J ElectricalSwing Alarm --- Audio warning device signals when theupper is swinging.LightsS Two working lights on front of the cabS One rotating amber beacon on top of the cab --- optionalS One amber strobe beacon on top of the cab --- optionalS Boom floodlight --- optional
35471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
J Load Hoist SystemLoad Hoist Performance
Front and Rear Winches --- 7/8 in (22mm) RopeMaximum Line Pull Normal Line Speed High Line Speed Layer Total
Front WinchStandard 7/8 22 18x19 rotation resistant --- right regular lay (Type RB) 17,520 7 946.9Optional 7/8 22 36x7 rotation resistant --- right regular lay (Type ZB) 20,920 9 489.2
2M Main and Optional Auxiliary WinchesS Axial piston, full and half displacement (2---speed) motorsdriven through planetary reduction unit for positive con-trol under all load conditions.
S Grooved laggingS Power up/down mode of operationS Hoist drum cable followerS Drum rotation indicatorS Drum diameter: 15 in (38.1cm)S Rope length:S Front: 850 ft (215.9m)S Rear: 500 ft (127.0m)
S Maximum rope storage: 951 ft (289.9m)S Terminator style socket and wedgeThird wrap indicator --- optional --- Visually and audiblywarns the operator when the wire rope is on the first (bot-tom) layer and when the wire rope is down to the last threewraps.
J EngineSpecification Detroit Diesel Series 40
Numbers of Cylinders 6
Cycle 4
Bore and Stroke: inch (mm) 4.59 x 5.35 (116.59 x 135.89)
Piston Displacement: in3 (L) 530 (8.69)
Max. Brake Horsepower: hp (kW) 330 (246) @ 2,000 rpm
Peak Torque: ft lb (Nm) 1,050 (1 424) @ 1,300 rpm
Electric/starting systems: volts 12/12
Alternator: amps 130
Crankcase Capacity: qt (L) 28 (26.5)
S Water/fuel separator on engineS 110---volt block heaterS Ether injection --- optional
4 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
J Drive SystemHydrostatic type consisting of two variable speed pistonpumps supplying hydraulic power to six hydraulic cam lobewheel drive motors computer controlled for smooth andreliable operation.
J Fuel TankOne 95 gal (359.6L) capacity tank
J Hydraulic SystemAll functions are hydraulically powered allowing positiveprecise control with independent or simultaneous operationof all functions.Main PumpsS One, two section gear pump for the boom hoist, tele-scope, and charge circuits.
S Two, closed---loop piston pumps serve as travel pumps.these two pumps supply hydraulic power to the wheelmotors.
S Two, closed---loop piston pumps are mounted to the rearof the two travel pumps. The left pump drives the frontwinch and the right pump drives the optional rear winch.
S One, pressure compensated piston pump mounted tothe rear of the left winch pump supplies hydraulic powerto the outrigger, counterweight removal (optional), oscilla-tion, and travel brake circuits.
S One, single section gear pump mounted to the rear of theright side winch pump supplies hydraulic power to theswing and steering circuits.
Hydraulic Reservoir --- 255 gal (96.5L) capacity equippedwith sight level gauge. Diffuser built in for deaeration. Mag-netic drain plug and large internal magnetFiltrationS One, 7---micron filter located inside hydraulic reservoir,accessible for easy replacement
S One, 7---micron charge filter located next to the reservoirwith an in---cab indicator light
S Two, 10---micron pressure filters located next to the reser-voir with change indicators
S Three, 100 mesh suction strainers located inside the hy-draulic reservoirCounterbalance Valves --- All boom extend cylinders andboom hoist cylinder are equipped with counterbalancevalves to provide load lowering and prevents accidentalload drop when hydraulic power is suddenly reduced.
J Pump DriveAll pumps are mounted on the pump drive gearbox andmechanically driven by the diesel engine.
J CounterweightTotal of 24,000 lb (10 886kg) consisting of two removablecounterweights pinned to the upper with capacities for 0 lb(0kg), 12,000 lb (5 443kg), and 24,000 lb (10 886kg) config-urations.S Optional --- Hydraulic counterweight removal activated bya hand---held controller with enough cable to access thepins on each side of the counterweights.
55471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
CarrierJ GeneralS 9 ft 11 in (3.02m) wideS 16 ft 1 in (4.90m) wheelbase (centerline of first axle tocenterline of third axle).Frame --- Box---type, torsion resistant, welded constructionmade of high tensile steel. Equipped with front and reartowing and tie---down lugs, tow connections, and accessladders.
J OutriggersBoxes --- Two removable, double box, front and rearpinned to carrier frame. Hydraulic outrigger pin removal ---optional.Beams and Jacks --- Four single stage beams with Con-fined Area Lifting Capacities (CALCt) provide selectableoutrigger extensions of full, intermediate, and retracted.Hydraulically controlled from the operator’s cab with inte-gral check valves.Pontoons --- Four lightweight, quick release, 26 in (0.66m)diameter, steel pontoons with contact area of 539 in2(3 477cm2) can be stored for road travel in storage rackson the carrier.Main Jack Reaction --- 132,000 lb (59 874kg) force and245 psi (1 689kPa) ground bearing pressure.
J Steering and Wheel Drive MotorsSteering --- Four independent modes consisting of twowheel front, four wheel rear, six wheel, and crab. Eachmode is controlled from the steering wheel and is selectedby a switch in the operator’s cab.Drive --- Three modes: 6 x 2 high, 6 x 2 low, and 6 x 6 foroff highway travelFront Drive Motors --- Steered, driven for 6 x 2 and 6 x 6Rear Drive Motors --- Steered, non---driven for 6 x 2 andsteered, driven for 6 x 6
J SuspensionFront --- Double “A” arms connected to oscillation cylindersthat lockout when the upper structure rotates 3˚ past cent-erlineLeft Rear --- Center and rear wheels mounted on double“A” arms connected to oscillation cylinders that lockoutwhen the upper structure rotates 3˚ past centerline. Os-cillation occurs across left center and left rear wheels.Right Rear --- Center and rear wheels mounted on double“A” arms connected to oscillation cylinders that lockoutwhen the upper structure rotates 3˚ past centerline. Os-cillation occurs across right center and right rear wheels.Ride Height Adjustment --- Suspension can be lowered fortransport using a hand---held controller from the ground.
J Tires and WheelsFront and Rear --- Six (single) 23.5 x 25---2 star radials,earthmover type tires on steel disc wheelsS Spare tires and wheels --- optional
J BrakesService --- Full hydraulic, dual circuit, disc type brakes onall wheel endsParking/Emergency --- Spring loaded type, acting on frontwheel ends
J ElectricalThree batteries provide 12 volt operation and startingLightsS Front lighting includes two main headlights and two park-ing/directional indicators
S Side lighting includes two parking/directional indicatorsper side
S Rear lighting includes two parking/directional indicators,two parking/brake lights, and two reversing lights
S Other equipment includes hazard/warning system
J Carrier Speeds and GradeabilityVariableHydrostaticDrive
Speed Gradeability
Range mph km/h % Grade
6 WD Low 3 4.8 55
2 WD Low 9 14.5 15
2 WD High 18.5 29.8 6
Based on a gross vehicle weight of 123,000 lb (55 792kg).Crane operating angle must not exceed 30˚ (66% grade).
J Hydraulic SystemFiltration --- One, 60---micron, full flow, line filter in thewheel motor case drain circuit. Filter includes an in---cabchange indicator. Accessible for easy filter replacement.
6 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
Axle LoadsBase machine with full tank of fueland 24,000 lb (10 886kg) ofcounterweight
Gross VehicleWeight (1)
Upper Facing Front Upper Facing RearFront Axle Rear Axle Group Front Axles Rear Axle Group
lb kg lb kg lb kg lb kg lb kg126,560 57 407 39,742 18 027 86,818 39 380 61,201 27 760 65,359 29 647
(1) Adjust gross vehicle weight and axle loading according to component weight.Note: All weights are ±3%.
C
BCrane Weight: 89,984 lb (40 816kg), equipped with:S 40---150 ft (12.19 ---45.72m), five section boomS 80 ton (72.57mt) hook blockS One winch with 850 ft (259.08m) of 7/8 in (22mm) ropeS 31---55 ft (9.45 ---16.76m) bi---fold flyS Winch rollerS Auxiliary armS Air conditioning
Drop Off Load Weight: 44,865 lb (20 350kg)S Two outrigger boxes with tow shacklesS 24,000 lb (10 886kg) counterweightS Rear winch with 500 ft (152.40m) of 7/8 in (22mm) ropeS Winch rollerS 12 ton (10.9mt) hook ball
Normal Suspension Collapsed SuspensionC [with 18 in (0.46m) Trailer] 13 ft 8 in (4.17m) 13 ft 5 in (4.09m)C [with 24 in (0.61m) Trailer] 14 ft 2 in (4.32m) 13 ft 11 in (4.24m)
ATransport Configuration and Weights
75471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
General Dimensions
28”(0.71m)
7’ 7.38” (2.32m)
11’ 2” (3.40m)
18’ 7” (5.66m)
26’ 0” (7.93m)
Full Retraction
Intermediate Extension
Centerline of tires
Full Extension
9’ 11”(3.02m)
12’ 0”(3.65m)
17.75”(0.45m)
10.29”(0.26m)
Turning Radius --- 2 Wheel Steering English MetricWall to wall over carrier 44’ 11” 13.69mWall to wall over boom attachment 55’ 1” 16.79mCurb to curb 41’ 9” 12.73mCenterline of tire 40’ 5” 12.32m
Turning Radius --- 6 Wheel Steering English MetricWall to wall over carrier 25’ 6” 7.77mWall to wall over boom attachment 37’ 8” 11.48mCurb to curb 22’ 3” 6.79mCenterline of tire 20’ 10” 6.35m
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
115471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
24,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
12 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
24,000 lb Counterweight -- On Tires -- Stationary -- Boom Centered Over Rear Between Tire Tracks(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
135471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
24,000 lb Counterweight -- On Tires -- Pick & Carry (Creep) -- Boom Centered Over Rear(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
155471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
24,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
16 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
24,000 lb Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Pounds)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers do not exceed 85% of the tipping loads and on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
18 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
10 885kg Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Kilograms)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
195471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
10 885kg Counterweight -- On Tires -- Stationary -- Boom Centered Over Rear Between Tire Tracks(All Capacities Are Listed In Kilograms)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
20 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
10 885kg Counterweight -- On Tires -- Pick & Carry (Creep) -- Boom Centered Over Rear(All Capacities Are Listed In Kilograms)
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
22 5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
10 885kg Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Kilograms)45.72m Main Boom Length --- 25˚ Fly Offset
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
235471 (supersedes 5431)---0506--- J7
RTC---80100 IILink-Belt Cranes
10 885kg Counterweight -- Fully Extended Outriggers -- 360˚ Rotation(All Capacities Are Listed In Kilograms)45.72m Main Boom Length --- 45˚ Fly Offset
This information is not for crane operation. Operator must refer to the in---cab information for crane operation. Rated lifting capacities shown onfully extended outriggers or on tires do not exceed 75% of the tipping loads.
5471 (supersedes 5431)---0506--- J7
RTC---80100 II Link-Belt Cranes
Link--Belt Construction Equipment Company Lexington, Kentucky www.linkbelt.comRLink--Belt is a registered trademark. Copyright 2006. We are constantly improving our products and therefore reserve the right to change designs and specifications.