TECHNICAL DATA SHEET EXPLOSION PROOF SERIES · Model X840/X841/X842 Grinder Pumps Class I, Division 1, Groups C & D Class I, Zone 1, Groups IIA and IIB PRODUCT SPECIFICATIONS MOTOR

© Copyright 2019 Zoeller® Co. All rights reserved.502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | zoellerpump.com

SECTION: 2.30.080FM2855

0519Supersedes

1018

Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.

TECHNICAL DATA SHEETEXPLOSION PROOF SERIES

Model X840/X841/X842 Grinder PumpsClass I, Division 1, Groups C & D

Class I, Zone 1, Groups IIA and IIB

PRODUCT SPECIFICATIONS

MO

TO

R

Horse Power 2

Voltage 200 - 575

Phase 1 or 3 Ph

Hertz 60 Hz

RPM 3450

Type Capacitor start / capacitor run or 3 Ph

Insulation Class F

Amps 4.5 - 20.0

PUM

P

Operation Nonautomatic

Discharge Size 1-1/4" NPT vertical

Cord Length 20' (6 m) standard

Cord Type UL listed, SOOW

Max. Head 125' (38.1 m)

Max. Flow Rate 54 GPM (204 LPM)

Max. Operating Temp. 104 °F (40 °C)

Cooling Oil filled

Motor Protection Auto reset thermal overload (1 Ph) or thermal sensor (3 Ph)

MA

TER

IALS

Cap Cast iron

Motor Housing Cast iron

Adapter Cast iron

Pump Housing Cast iron

Upper Bearing Ball bearing

Lower Bearing Ball bearing

Mechanical Seals Carbon/ceramic with stainless steel parts

Impeller Type Non-clogging vortex

Impeller Ductile iron

Hardware Stainless steel

Motor Shaft Stainless steel

Square Rings Neoprene

Cutter Hardened 440 C stainless steel, Rockwell C55-60

NOTE: See model comparison chart for specific details.

SK2837

11-27/32”(301 mm)

6-15/32”(164 mm)

4-1/4”(108 mm)

4-1/4”(108 mm)

8-1/2”(216 mm)

2 - 11-1/2 NPT(THREADS FOR CONDUIT CONNECTION)

26-31/32”(685 mm)

26-1/8”(664 mm)

4-9/16”(116 mm)

5-3/8”(137 mm)

NOT FOR USE IN ACIDIC ATMOSPHERES.

Certified to CSA StandardC22.2 No. 145

Tested to FM Standard 3600 & 3615

© Copyright 2019 Zoeller® Co. All rights reserved.502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | zoellerpump.com

Model X840 is a reversible grinder pump, and models X841 and X842 are single-direction grinder pumps.

016532

All installation of controls, protection devices and wiring should be done by a qualified licensed electrician. All electrical and safety codes should be followed including the most recent National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA).CAUTION

TOTAL DYNAMIC HEAD FLOW PER MINUTE

HEAD CAPACITY CURVEMODEL X840/X841/X842

0 40 80 120 160 200 240

706050403020100

104

8

12

16

20

130

70

60

50

40

30

20

FLOW PER MINUTE

GALLONSLITERS

TOTA

L DY

NA

MIC

HEA

D

80

9028

24

MET

ERS

FEET

100

110

120

32

36

X840 X841X842

TOTAL DYNAMIC HEAD/FLOWPER MINUTE

SEWAGE

MODELFeet

Shut-off Head:

X840Meters Gal. Liters

5102030 9.1

6.13.01.5

44

45

167

170

104 ft (31.7 m)

605040

908070

110100

120

12.215.218.321.324.427.430.533.536.6

423630 114

136159

231610 38

6187

3---- --

--11

125 ft (38.1 m)

X841Gal. Liters

45 17045 170

125 ft (38.1 m)

9525

134

20 764915

34

3229

34

34

3434

129

121110

129

129

129129

X842Gal.3434

129129

Liters

5249 185

197

433628 106

136163

19114 15

4272

54 20454 20454 20454 20454 204

ModelMODEL COMPARISON

Mode Volts Phase Amps HP Hz Lbs Kg

IX840 Non 200 1 20.0 2 60 155 70

IX841 Non 200 1 20.0 2 60 155 70

IX842 Non 200 1 20.0 2 60 155 70

EX840 Non 230 1 17.2 2 60 155 70

EX841 Non 230 1 17.2 2 60 155 70

EX842 Non 230 1 17.2 2 60 155 70

JX840 Non 200 3 12.3 2 60 155 70

JX841 Non 200 3 12.3 2 60 155 70

JX842 Non 200 3 12.3 2 60 155 70

FX840 Non 230 3 10.8 2 60 155 70

FX841 Non 230 3 10.8 2 60 155 70

FX842 Non 230 3 10.8 2 60 155 70

GX840 Non 460 3 5.5 2 60 155 70

GX841 Non 460 3 5.5 2 60 155 70

GX842 Non 460 3 5.5 2 60 155 70

BAX840 Non 575 3 4.5 2 60 155 70

BAX841 Non 575 3 4.5 2 60 155 70

BAX842 Non 575 3 4.5 2 60 155 70

016532

© Copyright 2019 Zoeller® Co. All rights reserved.502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | zoellerpump.com

STANDARD FEATURES:• cCSAus rated Class I, Division 1, Groups C & D and Class

Zone 1, Groups IIA & IIB Construction• Tested to FM standards 3600 and 3615 by CSA• Reversible cutter action manual/auto**• 1-1/4" NPT vertical discharge• Carbon/ceramic tandem seals• Thermal sensors** (overload on 1 Ph)• Moisture probes**• Vortex impeller: Ductile iron• Stainless steel cutter and plate (R-C 55-60)• Stainless steel shaft• Stainless steel lifting bail• Corrosion-resistant, powder coated epoxy paint• 20' (6 m) power cord - 20' (6 m) sensor cordOPTIONS: Extended cord lengths Bronze impeller Anti-siphon device

**Requires circuit in control panel to function Reversible feature only available on X840 models

¤ Single phase units require a set of capacitors and relay starting components.

VARIABLE LEVEL FLOAT SWITCH ASSEMBLY 3 Switches with weights and brackets

P/N 10-3237 WGT. 10 lb (4.5 kg) 4 Switches with weights and brackets

P/N 10-3238 WGT. 14 lb (6.4 kg)

CONTROL PANELSTANDARD FEATURES:• NEMA 4X outdoor rating• Intrinsically-safe relays• Audible and visible high water alarm• Starting, control, and alarm circuits• Circuit breaker and rated motor contactor (1 Ph)• Capacitors and motor starting relay (1 Ph)• Motor-protective switch (circuit breaker/adj

overloads) and rated motor contactor (3 Ph) • Alternating circuit (duplex)• Automatic reversing circuit (model X840 only)• High water alarm light• Internal seal leak light• HOA switches and pilot light(s)• Terminal strips• Thermal cut-out circuit (3 Ph only)• Padlock hasp• UL listed• Dry auxiliary contacts

OPTIONS: Flasher for high water alarm light Manual reset of high water alarm Elapsed time meters

* These control boxes consist of the reversing mechanisms and capacitors (1 Ph units) only. They will not control pumps. Refer to Section B for complete system controls. For duplex applications use two simplex reversing control boxes. (For pump prefix identification see News & Views 0052)

Note: All variable level float switches in this section are mechanically activated and do not contain mercury.

GRINDER SYSTEMSGRINDER MODELS X840/X841/X842

VERTICAL DISCHARGE - 20' (6 m) CORDS

P/N WGT. MODEL VOLTS

PH AMP

840-0064 155 lb (70.3 kg) EX840 230 1¤ 17.2

840-0065 155 lb (70.3 kg) IX840 200 1¤ 20.0

840-0066 151 lb (68.5 kg) JX840 200 3 12.3

840-0067 151 lb (68.5 kg) FX840 230 3 10.8

840-0068 151 lb (68.5 kg) GX840 460 3 5.5

840-0069 151 lb (68.5 kg) BAX840 575 3 4.5

841-0017 155 lb (70.3 kg) EX841 230 1¤ 17.2

841-0018 155 lb (70.3 kg) IX841 200 1¤ 20.0

841-0019 151 lb (68.5 kg) JX841 200 3 12.3

841-0020 151 lb (68.5 kg) FX841 230 3 10.8

841-0021 151 lb (68.5 kg) GX841 460 3 5.5

841-0022 151 lb (68.5 kg) BAX841 575 3 4.5

842-0011 155 lb (70.3 kg) EX842 230 1¤ 17.2

842-0012 155 lb (70.3 kg) IX842 200 1¤ 20.0

842-0013 151 lb (68.5 kg) JX842 200 3 12.3

842-0014 151 lb (68.5 kg) FX842 230 3 10.8

842-0015 151 lb (68.5 kg) GX842 460 3 5.5

842-0016 151 lb (68.5 kg) BAX842 575 3 4.5

CONTROL PANELS

SIMPLEX - NEMA 4 X DUPLEX - NEMA 4X

MODEL P/N WGT. P/N WGT.

EX or IX840 10-2709 26 lb (11.8 kg) 10-2713 34 lb (15.4 kg)

FX or JX840 10-2710 25 lb (11.3 kg) 10-2714 31 lb (14.1 kg)

GX840 10-2711 25 lb (11.3 kg) 10-2715 31 lb (14.1 kg)

BAX840 10-2712 25 lb (11.3 kg) 10-2716 31 lb (14.1 kg)

EX or IX841, 842 10-2717 24 lb (10.9 kg) 10-2721 30 lb (13.6 kg)

FX or JX841, 842 10-1568 24 lb (10.9 kg) 10-1596 27 lb (12.2 kg)

GX841, 842 10-1560 24 lb (10.9 kg) 10-1588 27 lb (12.2 kg)

BAX841, 842 10-2720 24 lb (10.9 kg) 10-2724 26 lb (11.8 kg)

For other options, please consult factory.

SIMPLEX REVERSING CONTROL BOXES*

AUTOMATIC MANUAL

MODEL P/N WGT. P/N WGT.

EX840 10-0352 8 lb (3.6 kg) 10-0360 7 lb (3.2 kg)

IX840 10-0352 8 lb (3.6 kg) 10-0360 7 lb (3.2 kg)

FX840 10-0353 6 lb (2.7 kg) 10-0361 5 lb (2.3 kg)

JX840 10-0353 6 lb (2.7 kg) 10-0361 5 lb (2.3 kg)

GX840 10-0353 6 lb (2.7 kg) Not available

BAX840 Not available Not available

© Copyright 2019 Zoeller® Co. All rights reserved.502-778-2731 | 800-928-7867 | 3649 Cane Run Road | Louisville, KY 40211-1961 | zoellerpump.com

• Fiberglass basin with anti-flotation ring• (2) Steel electrical couplings• 2" PVC discharge pipe from disconnect• 2" Adaptaflex discharge pipe seal• Non-sparking Z-Rail® disconnect system• 8' (2.4 m) stainless steel lifting cable • 3/4" stainless steel rail pipe • For basin depths to 84" (213 cm) [2’ (3.7 m) stainless steel

lifting cable for basin depths of 96" (244 cm)] • 2" PVC ball valve(s)• 2" cast iron check valve(s)• 1-4" rubber inlet pipe seal (field-installed)• Blank fiberglass cover with Zoeller imprint

SIMPLEX 24" x 60" (61 x 152 cm) P/N 33-0998 WGT. 189 lb (85.7 kg) 24" x 72" (61 x 183 cm) P/N 33-0999 WGT. 192 lb (87.1 kg) 24" x 84" (61 x 213 cm) P/N 33-1000 WGT. 213 lb (96.6kg) 24" x 96" (61 x 244 cm) P/N 33-1001 WGT. 235 lb (106.5kg)

 DUPLEX 36" x 60" (91 x 152 cm) P/N 33-1002 WGT. 393 lb (178.2kg) 36" x 72" (91 x 183 cm) P/N 33-1003 WGT. 468 lb (212.2kg) 36" x 84" (91 x 213 cm) P/N 33-1004 WGT. 533 lb (241.7 kg) 36" x 96" (91 x 244 cm) P/N 33-1005 WGT. 593 lb (268.9 kg) • Larger diameter or deeper basins (Allow for overhead clearance)

PUMP NOT INCLUDED

–– PREPACKAGED CHECKLIST ––

SIMPLEX(1) Grinder pump P/N ___________(1) Simplex control panel P/N ___________(1) Float switch assembly P/N ___________(1) Prepackaged basin assembly P/N ___________

DUPLEX(2) Grinder pump P/N ___________(1) Duplex control panel P/N ___________(1) Float switch assembly P/N ___________(1) Prepackaged basin assembly P/N ___________

2" FLEX BOOT FORDISCHARGE PIPE

2" DISCHARGE PIPE

3/4" SS GUIDE RAILS

CHECK VALVE

WEEP HOLE

NON-SPARKINGRAIL SYSTEM 1 1/4" X 2"

4" PIPE SEAL(SHIPPED LOOSE)

BLANK FIBERGLASS COVER

LIFTING CABLE

60" (152 cm)72" (183 cm)84" (213 cm)96" (244 cm)

36" (91 cm)

SHUT-OFF VALVE

SK2866

SK2867

24" (61 cm)

SHUT-OFF VALVE

2" DISCHARGE PIPE

3/4" SS GUIDE RAILS

CHECK VALVE

WEEP HOLE

NON-SPARKINGRAIL SYSTEM 1 1/4" X 2"

LIFTING CABLE

BLANK FIBERGLASS COVER

4" PIPE SEAL(SHIPPED LOOSE)

2" FLEX BOOT FOR DISCHARGE60" (152 cm)72" (183 cm)84" (213 cm)96" (244 cm)

OUTDOOR BASIN, COVER, AND RAIL SYSTEM ASSEMBLIESSTANDARD EQUIPMENT