Technical Application Guide for UP-SHINE LED Pendant Light UP-PL4012-25W-W
Technical ApplicationGuide for UP-SHINELED Pendant LightUP-PL4012-25W-W
Introduction
www.upshine.com [email protected]
Pendant led light acts as a decorative light in most applications. Elegant design creates soft lighting effect,various installation ways, such as suspended, surface mounted and recessed into ceiling. Perfect for hotels, restaurant, coffee shop etc. 300mm, 400mm, 500mm and 600mm diameter for wide choice.
● Up to 80% energy saving compared to standard CFL● Long lifetime of 40,000 hours ● 120° wide beam angle● CCT: 3000K 4000K 5000K 5700K ● No UV/IR light● Environment friendly, without Mercury or any other hazardous substances
Application notes● IP40 for indoor use only● Professional electrician for installation only
● Switch off before installation● Do not touch when in use● Keep away from hot steam and corrosive gas
Application AreasIt is widely used for various commercial and residential lighting applications, such as office, hotel, restaurant, home lighting etc.
Certificates
SAA
Technical Specifications
Model Voltage Power PowerFactor
Lumen(±5%)
Beamangle CCT Lifespan CRI Dimmable
UP-PL4012-25W-W AC100-240V 25W ≥0.9 1750 120o 3000K 40000h ≥80 No
UP-PL4012-25W-W AC100-240V 25W ≥0.9 2000 120o 4000K 40000h ≥80 No
UP-PL4012-25W-W AC100-240V 25W ≥0.9 2050 120o 5000K 40000h ≥80 No
UP-PL4012-25W-W AC100-240V 25W ≥0.9 2070 120o 5700K 40000h ≥80 No
UP-PL4012-25W-W-D AC200-240V 25W ≥0.9 1700 120o 3000K 40000h ≥80 Yes
UP-PL4012-25W-W-D AC200-240V 25W ≥0.9 1950 120o 4000K 40000h ≥80 Yes
UP-PL4012-25W-W-D AC200-240V 25W ≥0.9 2000 120o 5000K 40000h ≥80 Yes
UP-PL4012-25W-W-D AC200-240V 25W ≥0.9 2020 120o 5700K 40000h ≥80 Yes
Fixture CompatibilityRated
WattageElectrical
ClassificationIngress
Protection Operating
TempOperatingHumidity
Storage Temp
25W Ⅰ IP40 -20oC~45oC 0~90% -20oC~65oC
Driver data Sheet
Driver data Dim Non-dim
Input rated Voltage AC230V AC100-240V
Frequency 50Hz 50/60Hz
Input Voltage AC200-240V AC85-265V
Efficiency ≥85% ≥86%
Total load Wattage 25W±5% 25W±5%
Power Factor ≥0.9 ≥0.9
Rated input current ≤0.12A ≤0.28A
Full load output Voltage DC35-40V DC35-40V
Rated output current 580mA 580mA
Output current range 580mA±5% 580mA±5%
Tolerance ±5% ±5%
Current output tolerance ±5% ±5%
Dimming range 8%-100% —
Dimmer Triac dimmers —
Short circuit protection PASS PASS
Over voltage protection PASS PASS
Over temperature protection PASS PASS
Withstand voltage AC1500V AC1500V
www.upshine.com [email protected]
Product Information
Hei
ght a
djus
tabl
e
Ø400
Ø188
1255
Spectral Distribution
380 500 600 700 800 380 500 600 700 800
380 500 600 700 800 380 500 600 700 800
Wavelength(nm) Wavelength(nm)
Wavelength(nm) Wavelength(nm)
Max=6595 [1.0=20000] Max=7572 [1.0=20000]
Max=8572 [1.0=20000] Max=7373 [1.0=20000]
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
3000K
5000K
4000K
5700K
Photometric Diagram
Beam diagram Beam diagram
Beam diagram Beam diagram
Polar intensity diagram Polar intensity diagram
Polar intensity diagram Polar intensity diagram
Cartesian intensity diagram Cartesian intensity diagram
Cartesian intensity diagram Cartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 112.1 DEG
-/+180
-120
-90
-30
120
90
30
0
110
220
330
440
550
0
UNIT: cdAVERAGE BEAM ANGLE(50%): 115.3 DEG
-/+180
-120
-90
-30
120
90
30
0
110
220
330
440
550
0
UNIT: cdAVERAGE BEAM ANGLE(50%): 115.3 DEG
-/+180
-120
-90
-30
120
90
30
0
110
220
330
440
550
0
UNIT: cdAVERAGE BEAM ANGLE(50%): 114.9 DEG
-/+180
-120
-90
-30
120
90
30
0
110
220
330
440
550
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)5.5
4.95
4.4
3.85
3.3
2.75
2.2
1.65
1.1
0.55
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)5.5
4.95
4.4
3.85
3.3
2.75
2.2
1.65
1.1
0.55
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)5.5
4.95
4.4
3.85
3.3
2.75
2.2
1.65
1.1
0.55
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)5.5
4.95
4.4
3.85
3.3
2.75
2.2
1.65
1.1
0.55
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Height Eavg, Emax Angle: 113.77deg Diameter Height Eavg, Emax Angle: 113.09deg Diameter
Height Eavg, Emax Angle: 112.66deg Diameter Height Eavg, Emax Angle: 117.25deg Diameter
Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 1680 lm Flux out: 1800 lm
Flux out: 1870 lm Flux out: 1920 lm
0.4687, 2.123fc5.021, 15.24lx
0.5478, 1.868fc6.897, 20.10lx
0.502, 1.754fc5.764, 19.21lx
0.5871, 1.451fc5.758, 19.11lx
47.04ft1455.60cm
49.65ft1513.39cm
48.54ft1480.03cm
47.05ft1503.22cm
9.69ft295.34cm
9.93ft302.68cm
9.686ft298.99cm
9.61ft296.55cm
19.38ft590.68cm
19.86ft605.36cm
19.41ft595.13cm
19.15ft590.58cm
29.07ft886.02cm
29.79ft908.04cm
29.4ft890.01cm
28.77ft876.93cm
38.76ft1181.36cm
39.72ft1210.72cm
39.14ft1193.11cm
38.36ft1169.25cm
14.55, 48.94fc156.7, 526.8lx
13.70, 46.69fc147.4, 502.6lx
15.21, 45.30fc142.2, 465.3lx
13.42, 44.15fc140.1, 463.4lx
3.638, 12.24fc39.16, 131.7lx
3.424, 11.67fc36.85, 125.6lx
4.510, 12.61fc45.12, 185.6lx
4.321, 11.03fc37.33, 120.4lx
1.617, 5.438fc17.41, 58.53lx
1.522, 5.188fc16.38, 55.84lx
1.742, 5.632fc15.32, 57.54lx
1.425, 4.988fc15.63, 51.24lx
0.9096, 3.059fc9.791, 32.92lx
0.8560, 2.918fc9.214, 31.41lx
0.888, 3.015fc9.054, 32.44lx
0.8344, 3.425fc9.151, 29.33lx
3.281ft
1m
3.281ft
1m
3.281ft
1m
3.281ft
1m
13.12ft
4m
13.12ft
4m
13.12ft
4m
13.12ft
4m
9.843ft
3m
9.843ft
3m
9.843ft
3m
9.843ft
3m
6.562ft
2m
6.562ft
2m
6.562ft
2m
6.562ft
2m
16.4ft
5m
16.4ft
5m
16.4ft
5m
16.4ft
5m
4.17SDCM F3000K
x=0.4702 y=0.4228
3.60SDCM F5700K
x=0.3523 y=0.3684
3.09SDCM F5000K
x=0.3866 y=0.3848
3.86SDCM F4000K
x=0.4472 y=0.4107
5000K 5700K
3000K 4000K
www.upshine.com [email protected]
80
70
60
50
40
30
20
10
0
Tem
pera
ture
(o C)
Time
The driver lifespan is based on capacitor working temperature.
Driver lifetime & LED lifetime
90000
80000
70000
60000
50000
40000
30000
20000
10000
065oC 75oC 85oC 95oC 105oC
Life
time
(hou
rs)
Capacitor Tc (oC)
Driver Lifetime LED Lifetime
% L
umin
ous
Flux
FLUX
△ U'V'
110%
105%
100%
95%
90%
85%
80%
75%
70%
0.0040
0.0035
0.0030
0.0025
0.0020
0.0015
0.0010
0.0005
0.00000 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
LifeTime (hours)
Polar Diagram Comparison
AVERAGE BEAM ANGLE (50%): 115.4DEG
UNIT: cd
C0/180, 112.9 deg
C30/210, 114.9 deg
C60/240, 114.1 deg
C90/270, 113.4 deg
110
220
330
440
550
0O
+/-180O
150O-150O
120O-120O
90O-90O
60O-60O
30O-30O
0
14:2
9:22
15:2
0:16
16:1
1:16
17:0
2:16
17:5
3:16
18:4
4:16
19:3
5:16
20:2
6:16
21:1
7:16
22:0
8:16
22:5
9:16
23:5
0:16
0:41
:16
1:32
:16
2:23
:16
3:14
:16
4:05
:16
4:56
:16
5:47
:16
6:38
:16
7:29
:16
8:20
:16
IC
Capactior
MOS
PCB
Fitting
Voltage transformer
Environmental temperature
Temperature● The testing is operated at 25°C
● The lifetime of capacitor, minimum of 5,000 hours if operated at 105°C, will be doubled whenever the temperature drops 10°C
● The highest withstand temperature of IC, MOS could be 120°C
● The highest withstand temperature of LED junction temperature is 150°C
www.upshine.com [email protected]
Installation
Suspended installation (Wooden ceiling):
1. Unbox panel light and accessory pack.2. Switch off, fix bracket into ceiling with
screw.
4. Fix the wall mount bracket into ceiling by screw.
5. Hang panel to suspending rope and connect the DC connector
6. Adjust the length of hanging wire to proper height, Restore the power and switch on.
Suspended installation (Concrete ceiling):
1. Unbox panel light and accessory pack 2. Power off, Punch holes and knock the plastic anchor into ceiling
3. Fix bracket into ceiling with screw.
4. Insert the hanging wire into wall mount bracket; connect L/N/E to mains supply.
5. Fix the wall mount bracket into ceiling by screw.
6. Hang panel to suspending rope and connect the DC connector
www.upshine.com [email protected]
3. Insert the hanging wire into wall mount bracket; connect L/N/E to mains supply.
N =L =
YELLOW-GREEN
BROWNBLUE
=
N =L =
YELLOW-GREEN
BROWNBLUE
=
7. Adjust the length of hanging wire to proper height, Restore the power and switch on
N =L =
YELLOW-GREEN
BROWNBLUE
=ON
OFF
1.Determine the mounting location, ceiling opening 200-220mm, mark the hole position of wall mount box and knock the plastic anchor into ceiling
1. Determine the mounting location, mark the hole position of wall mount box and knock the plastic anchor into ceiling.
2. Take out the wall mounted box from round panel by clockwise rotation. Disconnect the DC plug and fall-prevention rope.
3. Fix the wall mount box on ceiling tightly by screws.
2.Take out the wall mounted box from round panel by clockwise rotation. Disconnect the DC plug and fall-prevention rope.
4. Connect the AC wires to the connection terminals in the mount box.
5. Connect fall-prevention rope and the DC plug, then rotate anticlockwise the round panel into wall mount box until it is firmly attached.
3. Insert the wall mount box into the hole in the ceiling, fix it tightly by screws.
6. Installation complete, switch on.
Recessed installation:
Surface mount installation:
www.upshine.com [email protected]
www.upshine.com [email protected] Phone: +86 755 2919 7332Add: 2nd building Dingfeng High-Tech Zone, Fuyuan 1st road, Fu Yong Sub-district, Bao'an, Shenzhen China
SIZE(CM) N.W/pc(KGS) G.W.(KGS) Q'TY(PCS)
Carton 45.5*21.5*65 3.1 13.3 4
SIZE(CM) N.W/pc(KGS) G.W.(KGS) Q'TY(PCS)
Carton 46*30.5*46 3.3 13.7 4
CTNS Q'TY(PCS) VOLUME(CBM)
20'' standardcontainer 433 1732 28
40'' standardcontainer 866 3464 56
CTNS Q'TY(PCS) VOLUME(CBM)
20'' standardcontainer 426 1704 28
40'' standardcontainer 852 3408 56
Packaging Information(Suspended)
(Surface mount & recessed)
N =L =
YELLOW-GREEN
BROWNBLUE
=
ON
OFF
4. Connect the AC wires t o the connec t i on terminals in the mount box.
5. Connect fall-prevention rope and the DC plug, then rotate anticlockwise the round panel into wall mount box until it is firmly attached.
6. Installation complete, switch on.