This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
PackagingTape and Reel Specification for Integrated Circuits
COMMON INFORMATION
TB347Rev.34
Oct 15, 2021
IntroductionMany Surface Mounted Devices (SMDs) are packaged for shipment in embossed tape and wound onto reels. The Renesas tape and reel specifications comply with the Electronics Industries Association (EIA) standards for “Embossed Carrier Taping of Surface Mount Components for Automatic Handling”.
• EIA-481 for 8, 12, 16, 24, 32, 44, and 56mm Wide Tape
(Except the orientation of square package)
Renesas now supplies many different SMDs in tape and reel, as shown in Table 1.
TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued)
PACKAGETYPE
# OFLEADS
NOMINAL PACKAGESIZE
UNITS PER REEL
REEL AND HUB SIZE
(Note 3)
TRAILER “A” LEADER “B” POCKET TAPE
POCKETS LENGTH POCKETS LENGTH WIDTHPITCH(P1)
TB347 Rev.34 Page 8 of 18Oct 15, 2021
Packaging Tape and Reel Specification for Integrated Circuits
ODFN 8 2.36x2.94x1.35mm 1000/250
7&2.4/7&2.4
40 320mm 100 800mm 12mm 8mm
NOTES:
1. Pocket count and trailer and leader lengths are nominal counts/dimensions.
2. Package size in inches (unless otherwise indicated).
3. Reel and hub size; Example: 13&4 = 13 inch reel with 4 inch hub.
4. Multiple lead counts.
5. Dependent upon the specific package type. Reference specific package type and number of leads in Table 1 for additional information.
6. Products starting with “TW”
7. Products starting with “ZL”
8. Products starting with “Q”
TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued)
PACKAGETYPE
# OFLEADS
NOMINAL PACKAGESIZE
UNITS PER REEL
REEL AND HUB SIZE
(Note 3)
TRAILER “A” LEADER “B” POCKET TAPE
POCKETS LENGTH POCKETS LENGTH WIDTHPITCH(P1)
TB347 Rev.34 Page 9 of 18Oct 15, 2021
Packaging Tape and Reel Specification for Integrated Circuits
General InformationThe Renesas tape and reel packing system protects the product from mechanical and electrical damage and is designed for automatic pick-and-place equipment.
The tape and reel packing system consists of a pocket carrier tape sealed with protective cover tape to hold the devices in place.
The devices are loaded into the carrier pockets with leads down.
The tape is wound onto a plastic reel for labeling and then packaged for shipment.
All tape sizes are supplied on 7inch and 13inch diameter reels.
The conductive carrier tape and antistatic coated transparent cover tape and reel provide ESD protection.
Information labels, ESD labels, and barcode labels (if required) are placed on each reel.
Transparent cover tape allows device verification and brand inspection without having to remove or handle components.
No more than two date codes are combined on any one reel.
FIGURE 1. TAPE/REEL AND LABEL INFORMATION
FIGURE 2. TAPE LEADER AND TRAILER
CARRIER TAPE
EMBOSSED CAVITY
BARCODE LABEL
ESD CAUTION
TOP COVER TAPE
SPROCKET HOLE(ROUND)
NOTE: LABELS TO BE PLACED ONTHE REEL OPPOSITE THE ROUND(TAPE) SPROCKET HOLES.
ANY ADDITIONAL LABEL(IF REQUIRED)
IF REQUIRED
WAREHOUSE LABEL
IF REQUIRED
ENDCARRIER TAPE
COVER TAPE
START
COVER TAPE TRAILER
POCKETS
AND LENGTH “A”
COMPONENTSLEADER
POCKETS
AND LENGTH “B”
TB347 Rev.34 Page 10 of 18Oct 15, 2021
Packaging Tape and Reel Specification for Integrated Circuits
Materials and DesignCarrier TapeThe pocketed carrier tape is made of conductive polystyrene plus carbon material (or equivalent). The surface resistivity is 106Ω/sq. maximum.
Pocket tapes are designed so that the components remain in position for automatic handling after the cover tape is removed.
Each pocket has a hole in the center for automated sensing of whether the pocket is occupied, thus facilitating device removal.
Sprocket holes along the edge of the carrier tape enable direct feeding into automated board assembly equipment.
See Figures 3 and 4 for carrier tape dimensions.
Cover TapeThe cover tape is made of antistatic transparent polyester film.
The surface resistivity is less than 1010Ω/sq. maximum.
The cover tape is heat-sealed or pressure sealed to the edges of the carrier tape to encase the devices in the pockets.
The force to peel back the cover tape from the carrier tape shall be a mean value of 30gm to 80gm (0.3N to 0.8N).
ReelThe device loading orientation is in compliance with EIA-481 (see Figure 5).
The loaded carrier tape is wound onto a reel that is uniformly sized for all packages (see Figure 6).
The reel is made of antistatic high impact polystyrene. The surface resistivity is less than 1010Ω/sq. maximum.
NOTE:29. Dimensions are in millimeters (inches are in parentheses for reference only).
TB347 Rev.34 Page 17 of 18Oct 15, 2021
Packaging Tape and Reel Specification for Integrated Circuits
Revision History
DATE REVISION CHANGE
Oct 15, 2021 34 Added 3000/reel into 7X7 QFN packing spec.Added FCQFN 4X4 QFN on the standard 4X4 QFN packing specAdded 1.28x 1.36mm WLCSP packing spec.Added 3.74x4.14mm WLCSP packing spec.Added 3x3x1.7mm LGA packing spec.
Jan 13, 2020 33 Removed 32LD uTDFN 5 x 5 x 0.63 mm (Not used) from page 8.Added 32LD PQFN 5 x 5 x 0.63 mm Tape/Reel information on page 8.Added 32LD PQFN 5 x 5 x 0.77 mm Tape/Reel information on page 8.Added 39LD PQFN 5 x 7 x 0.75 mm Tape/Reel information on page 8.
Corporate HeadquartersTOYOSU FORESIA, 3-2-24 Toyosu,Koto-ku, Tokyo 135-0061, Japanwww.renesas.com
Contact InformationFor further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit:www.renesas.com/contact/
TrademarksRenesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products.