TA-4J S.A. 49 458 1/48 scale detail set for HASEGAWA kit • sada detailù pro model 1/48 HASEGAWA ORIGINAL KIT PARTS PÙVODNÍ DÍLY STAVEBNICE PHOTO-ETCHED PARTS LEPTANÉ DÍLY PARTS TO BE REMOVED DÍLY K ODSTRANÌNÍ FILL TMELIT eduard REMOVE ODSTRANIT OPTION VOLBA ? REPLACE NAHRADIT BEND OHNOUT GRIND OBROUSIT SYMETRICAL ASSEMBLY SYMETRICKÁ MONTÁŽ DRILL HOLE VRTAT OTVOR APPLY EXPRESS MASK AND PAINT BEFORE GLUING POUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM 1/7 49 458 REFERENCES: Aeroguide #14 FOR BOTH SEATS E36 ( V28 ) E35 ( V27 ) E41 ( V31 ) E41 ( V31 ) E34 V18 E33 V19 10 26 32 17 18 6 34 11 25 21 7 33 12 31 14 24 36 35 9 8 20 19 film In detail & scale #32 FOR BOTH SEATS FOR BOTH SEATS FE 458 + 49 458 TA-4J
7
Embed
TA-4J S.A. eduard · 2013. 5. 22. · LEPTANÉ D LY PARTS TO BE REMOVED ... 8 9 36 35 19 20 film In detail & scale #32 FOR BOTH SEATS FOR BOTH SEATS FE 458 + 49 458 TA-4J. 2/7 49
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
TA-4J S.A.49 4581/48 scale detail set for HASEGAWA kit • sada detailù pro model 1/48 HASEGAWA
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
For futher detail sets look for 48 631 TA-4J Airbrakes and 48 644 A-4 ladder
(not included in this set)
eduard
30
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.