-
For: SYRF204D series systems
SYRF204D-LCD System
PLEASE READ THIS MANUAL BEFORE USING YOUR SYSTEM, and always
follow the instructions for safety and proper use. Save this manual
for future reference.
SYRF204D_SI 11/29/12
SYRF204D 4-Camera Digital Wireless System Installation and Setup
Guide
-
ii
CAUTION Operate this device only in environments where the
temperature or humidity is within the recommended range.
Operation
at extreme temperatures or in very high or low humidity levels
may cause electric shock and shorten the life of the product.
CAUTION Installation and servicing should be performed by
qualified and experienced personnel only. DVR should always remain
OFF
during any installation process.
CAUTION Do not use the camera if fumes, smoke or a strange odor
is emitted from the unit, or if it seems to function
incorrectly.
Disconnect the power source immediately, and consult your
dealer.
FCC NOTICEThis equipment has been tested and found to comply
with R&TTE standards or Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications.
FCC CAUTIONTo assure continued compliance, use only shielded
interface cables when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party
responsible for compliance could void this device of which
operation is subject to the following two conditions
1. Thisdevicemaynotcauseharmfulinterference.
2.
Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
-
iii4-Camera Digital Wireless System Setup Guide
SAFETY INSTRUCTIONS
Safety Instructions
• Toreduceriskofelectricshock,donotdisassemblethisdevice.•
Useonlythepowersuppliesprovidedwiththedevice.•
Defectivepartsmustbereplacedbyoriginalsparepartsonly.•
IfyouspillliquidontheDVR,unplugitfromtheACoutlettopreventpossiblefireorshockhazard,thenconsultauthorized
servicepersonnelforrepair.•
Whencleaningthedevice,turnitofffirst.Useacleansoftclothmoistenedwithalittlebitofwatertocleanit.•
Ifthedevicedoesnotworkproperly,returnittothedealerwhereitwaspurchased.Donotdismantleitbyyourself.•
Donotusethedeviceclosetoheater,refrigeratororstove.•
Wheninuse,donotpointthecameratowardanybrightlight.•
HandleyourDVRwithcare;itcontainsaharddiskdrive.
—
Itispossibletodamageharddrivesiftheyaremovedwhiletheirmotorsarestillrunning.Toallowtheharddrivetospindownandparkitsheads,waitatleast10secondsafterdisconnectingpowerbeforemovingtheunit.
—
Toavoidshockandvibrationdamagetotheinternalharddrive,donotmovetheunitwhileitispluggedin.—
Protectharddiskdrivesfromstaticelectricity.—
Donotstackharddiskdrivesorkeepthemupright.—
Donotuseanelectricormagneticscrewdrivertofixharddiskdrives.
•
Donotplacetheunitinanenclosedareawheretheairflowthroughthecoolingventsisimpeded.•
Protectthepowercordfrombeingsteppedonorpinchedparticularlyatplugsandthepointswheretheyexitfromthe
apparatus.•
Donotdropmetallicpartsthroughslots.Thiscouldpermanentlydamagethedevice.Turnthepoweroffimmediatelyand
contactqualifiedservicepersonnelforrepair.•
Donotoverloadoutletsandextensioncordsasthismayresultinariskoffireorelectricshock.
-
iv
TABLE OF CONTENTS
Table of Contents
SECTION 1 Systems Overview . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 11.1 Aboutthisdocument. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .11.2
Controlsandconnectors. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .2
1.2.1 DVRFrontPanel. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .21.2.2 DVRBackpanel. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .31.2.3 Cameracomponents. . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .41.2.4 Camerabackpanel . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .51.2.5 Mousecontrol.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.6
SECTION 2 Installing Your System . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 72.1 Gettingstarted:Unpackingtheequipment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .72.2 Cameraplacement. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .82.3 DVRplacement. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92.4
DVRInstallation . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .102.5 Camerainstallation . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .11
SECTION 3 DVR Setup . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 143.1 LogintotheDVR . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .143.2
Configuringthesystem. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .15
3.2.1 Settingthescreenlanguageandvideosystemformat. . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .163.2.1
Settingthesystemtime. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.163.2.2 ChangetheAdminanduser1passwords . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183.2.3
Adduserstothesystem. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.193.2.4 SetHDDoverwriteoption. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .20
3.3 Recordconfigurationsettings. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .213.4 Videoconfigurationsettings. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .23
3.4.1 Videosetup. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . .253.5 Networkconfigurationsettings . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .263.6 Alarmconfigurationsettings . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .27
3.6.1 Motiondetectionsetup. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .28SECTION 4 Networking Your DVR . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . 31
4.1
ConfiguretheDVRforaccessonyourhomenetwork......................................324.1.1
VerifylocalnetworkconnectabilitywithIE . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.2 AccessingyourDVRfromtheInternet. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.41SECTION 5 Accessing Your DVR With a Web Browser . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 44
-
v4-Camera Digital Wireless System Setup Guide
TABLE OF CONTENTS
5.1 ConnectingtoyourDVRwithIE . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .445.2 Livescreen. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .455.3 Replaywindow. . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .465.4
Remotewindow. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .465.5 Localsetting . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .475.6 Logout . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.48
SECTION 6 KWeye Smartphone App . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . 496.1 InstallingKWeye. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .49
6.1.1 InstallingKWeyeiniPhone . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .496.1.2 InstallingKWeyeinAndroid . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . .51
6.2 SetupaccesstoaDVR . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .516.3 UsingKWeye. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .52
SECTION 7 DVR System Menus Reference . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . 547.1 Menutree . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .54
7.1.1 ToolBar. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . .557.1.2 Menuoptions. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .56
7.2
Systemmenu.......................................................................577.2.1
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .577.2.2 VideoSystem . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .577.2.3 TimeSetup. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .577.2.4 Usermanagement.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .587.2.5 HDD. .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .617.2.6 Maintenance. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .617.2.7
Information....................................................................63
7.3 Record . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .637.3.1 RecordChannel . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .647.3.2 Record. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.647.3.3 Bit-rate . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .647.3.4 Resolution . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .647.3.5 FrameRate. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .647.3.6
Packtime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . .647.3.7 RecordMode. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .65
7.4 Video. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .667.4.1 VideoChannel . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .667.4.2 Name. . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.66
-
vi
TABLE OF CONTENTS
7.4.3 Position. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .667.4.4 Live . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .667.4.5 Color . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .667.4.6 RecordTime . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . .677.4.7 Margin. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .677.4.8 VideoSetup . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
7.5 Network. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .687.5.1 NetworkSetup. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .687.5.2
DDNSSetup....................................................................707.5.3
EmailSetup. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .717.5.4 MobileMonitor . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .72
7.6 Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .737.6.1 Output. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .737.6.2 Duration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .737.6.3 Buzzer. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . .737.6.4 Prerecord. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .737.6.5 Exception . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.747.6.6 I/OAlarm. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . .747.6.7 MotionDetection. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .76
7.7 PTZ . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .777.7.1 Channel. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .787.7.2
Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . .787.7.3 BaudRate. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .787.7.4 DataBit. . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .787.7.5 StopBit.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. .787.7.6 Parity. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . .787.7.7 Address. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .78
SECTION 8 Cleaning . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . 79SECTION 9 Specifications . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80APPENDIX A Off-loaded Video Files . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 82APPENDIX B Troubleshooting . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . 83APPENDIX C
DVR Compatible HDDs . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . 86APPENDIX D Compatible USB DVD Recorders . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 87
-
14-Camera Digital Wireless System Setup Guide
SECTION 1: SYSTEM OVERVIEW
SECTION1 Systems
OverviewCongratulationsonpurchasingyour4-CameraDigitalWirelessSystem!Yoursystemincludes:
• 4channel2.4GHzwirelesssystem16QAM/QPSK/BPSKdigitalmodulation•
4channelswirelessor2channelswiredoptional•
H.264DVRsystemwithnetworkfunction;canbeconfiguredlocallyoracrossanetworkwithMicrosoft®InternetExplorer®
(IE)browser.• EasytouseGUI•
Longrecordingtime,upto20dayswith500GBHDD@25fps•
500GBHDDwithremovableHDDrack• USBmouse•
Camerahas24IRLEDsfornightvision• Supportdualcodingstream•
Supportnetworkfilesharefunction•
SupportFourchannelsimultaneousplayback•
Support3GmobilephonesurveillanceandE-mailfunction.•
Transmissiondistanceupto325ft(lineofsight)•
LCD17”monitor(withSYRF204D-LCDsystemonly)•
BackupfilescompatiblewithMicrosoftWindowsMediaPlayer
1.1 About this document
Thisdocumentisasimplifiedguidetosettingupabasicsystem.FordetailedinformationaboutyourDVRandcamerasystem,refertotheDVRUserManual.
-
2
SECTION 1: SYSTEM OVERVIEW
1.2 Controls and connectors
1.2.1 DVRFrontPanel
Single/Multi Camera Display
Toggle
tqpu Menu Navigation
Buttons
Enter
Rewind
Menu / Escape
Play / Pause
Record
CH1 .. CH4 Camera Select
Stop
Forward
Button Usage
CH1..CH4
Usedtoselectthecameraonchannel1,2,3,or4forfullscreenview
o/ Togglesbetweensinglecamera,multi-cameradisplay.
ENTER Presstoconfirmamenuchoice.
MENU/ESC Accesstoolbar/hidetoolbar/exitmenu/exitsubmenu
REW
Presstorewindvideoplayback.Pressrepeatedlytorewind2X,4x,8xnormalspeed.
u/II
Whenarecordedfileisselected,pressthisbuttontoplay.thenpressitagaintopauseplayback.
STOP Stopplayback.
FWD
Pressforfastvideoplayback.Pressrepeatedlytoadvance2X,4x,8xnormalspeed.
REC Usetostartandstopmanualrecording.
tqpuUsethesebuttonstonavigatethroughthemenusystem.Generally,usethetubuttonstomovetoselectionboxes,andusetheqptoselectsubmenuparameters.
POWER PowerOnLED
HDD HDDactivityLED.
-
34-Camera Digital Wireless System Setup Guide
SECTION 1: SYSTEM OVERVIEW
1.2.2 DVRBackpanel
Input Selector for CH2, CH4
wire or wireless
CH1, CH2 (wired) video In
Wireless antenna connectors (CH1 - CH4)
LAN Main Out (BNC)
Power Switch
Sensor In/Alarm Out,RS485
connections
PAIR button (1 - 4)
Main Out (VGA)
USB ports
Fan Grill
Power DC 12V
Connector / Button Usage
Pair button (1 - 4)
Buttonformanualtransmitter/receiverlinkpairing(channels1-4)
Main Out (VGA) ConnectorforVGAmonitor
CH2, CH4 (wired) video In
BNCconnectorsforwiredinputstochannels2and4.TheseportsareenabledwhentheinputselectorswitchforthechannelisintheCH2/CH4position.
Wireless antenna connectors
SMAconnectorsforwirelessinputstochannels1-4(lefttoright)
Power switch Maininputpowerswitch.
USB ports
USBportstoconnectamouseorabackupdevicesuchasaflashdriveorDVDrecorder.
Input selector for CH2, CH4 wire or wireless
Switchtoenablewired(BNCconnectorsforCH2,CH4)orwireless(RFSMAwirelessconnectorsforCH2,CH4)videoinput.
MAIN OUT BNC
BNCcompositevideooutputtodisplaydevice(75Ω,1Vp-p)
LAN StandardRJ45Ethernet10BaseT,100BaseTportwithautodetect.
Alarm In/Out RS485 connections Sensor/Alarm/RS-485interface(
MAIN OUT VGA
StandardVGAoutputtoadisplaydevice,suchasacomputermonitor.
LAN StandardRJ45Ethernet10BaseT,100BaseTportwithautodetect.
ALARM IN, ALARM OUT, RS485
Usetheseconnectorstoattachexternalsensordevices,alarmreportingdevices,anddeviceswithanRS485controlinterface,suchasPTZcameras.SeetheDVRUserManualformoreinformation.
DC 12V Connectto12VDCpoweradapter.
POWER Powerswitchtoturntheunitonandoff.
-
4
SECTION 1: SYSTEM OVERVIEW
Sensor, Alarm, RS485 connectors
Sensorinputs1-4
Sensorinputground Alarmoutput
RS485A,B
Groundterminals
1.2.3 Cameracomponents
Adjustable Sun Shield
Antenna
Lens
Mounting Bracket Assembly
Mounting Plate
Gimbal Lock Knob
IR Array
Power LED
Light Level Sensor
Power Drop Cable
-
54-Camera Digital Wireless System Setup Guide
SECTION 1: SYSTEM OVERVIEW
1.2.4 Camerabackpanel
AntennaSMAconnector
Antenna
Powerdropcable
ChannelselectswitchesNOTE:Switchblockisinvertedoncamera
Sunshield
Pairingbutton
Camera back show with plugs removed
PAIRing button
PAIRingthecameraisaprocesstosynchronizeacameratooperateonachannelwiththeDVR.Normally,thecameraandDVRsynchronizetheirconnection(PAIR)automatically.However,ifmanuallypairingisrequired,dothefollowing:
1. Removetwoplasticcapsontherearofthewirelesscamera.
2. Setchannelselectswitchestothechanneltowhatyouwant(seeChannel
select switch settings).
3. PoweronthecameraandDVR.
4.
Forthechannelthecameraisconfiguredfor,pressandholddownthePAIRbuttononthebackoftheDVRfor3seconds.
5. WhentheDVRmonitordisplaysthemessage“Please press paring
button of TX
device”,pressandholddownthePAIRingbuttonthebackofthecamera(TXdevice)untilthecamerapowerLEDbeginstoflash.Youmustpressthepairbutton
-
6
SECTION 1: SYSTEM OVERVIEW
thecamerawithin58secondsoftheappearanceofthemessageontheDVR,otherwise,themessage“Pairing
failed”willappear.
WhenthePAIRingiscomplete,theDVRmonitorscreenwillshow“Paring OK
Save
data“andthepowerLEDofthewirelessDVRwillbelitconstantly.IfthePAIRingprocessfailed,themessage“Link
failed”willappear.
6.
AfterthePAIRingiscomplete,reinstalltheplasticcapsonthebackofthecameratosealthePAIRingbuttonandchannelselectswitchaccesses.
Channel select switch settings
EachcamerainyourSYRF204Dkitwaspresetatthefactorytoaitsownchannelnumber.However,ifyouneedtochangethesesettings,usethefollowingtabletoconfigureyourcamerastooperateondifferentchannels.Eachcameramustoperateonitsownchannel.
Switch
Channel select
1 2 3 4
1 Off On Off On
2 Off Off On On
1.2.5 Mousecontrol
ThemouseoperatesjustlikeamouseonaWindowsPC.ConnectthemousetotheUSBconnectorinthebackpanel.
Action Effect
RightclickInlivedisplaymode,rightclicktoeitherdisplayorhidethetoolbar.
Inmainmenuorsubmenumode,rightclicktoexitthecurrentmenu.Notethatthesettingswillnotbesavedafterrightclicking.
Leftclick
Onmenuunlockmode,inthetoolbarleftclickontheSYSTEMSETTINGSicon,
,toenterintothemainmenu.
Afterenteringmainmenu,leftclicktoentersubmenus.
Inmenumode,leftclickthePLAYicon, ,toreviewvideofiles.
Leftclicktoselectvaluesineditboxesorpull-downmenus.Thesystemsupportsspecialsymbols,numbersandletters.
LeftclickthePLAYicon, ,toenterplaybackmode.Leftclick>>
tocontroltheforwardfunction,>ISlowplayfunction,I>frameplayfunction,>Playfunction,andXexitfunction.
IntheVIDEO|VIDEOSETUP|COLORSETUPconfigurationwindow,youcanleftclicktoadjustcolorcontrolbarandscreencontrolbar.
Inthemainmenu,submenuorplaybackview,leftclick“x”toexit/closethecurrentmenu.
IntheALARM|MOTION|MDAREAconfigurationwindow,leftclickanareasegmenttoselect/deselectitformotionsensing.
Doubleclick
Inlivevieworduringvideoplayback,double-clicktomaximizechannelonthescreen.
MousedragIntheALARM|MOTION|MDAREAconfigurationwindow,presstheleftmousebuttonanddragtoframeanareatosenseformotiondetection.
Usethemousetoselectmenuitems.
-
74-Camera Digital Wireless System Setup Guide
SECTION 2: INSTALLING YOUR SYSTEM
SECTION2 Installing Your System
2.1 Getting started: Unpacking the equipment
Yoursystemincludes:
• 4-channelH.264networkableDVRwithfourantennasandapoweradapter•
BNCtoRCAextensioncable(3ft,2wire,notshown)• USBmouse•
4wirelesscameras,eachwithamountingbracket,poweradapterandantenna•
Thismanual,mini-CDwithsmartphoneapplications(onCD)•
LCDMonitor(withSYRF204D-LCDsystem,notshownbelow)
Removetheequipmentfromitspackagingandplaceitonaflat,cleansurface.Inspecteachitem.Ifanyvisibledamageispresent,contactyourdistributorforareplacement.Verifythatyourorderiscomplete.
Cameras
Mouse
DVR
DVR Power
Adapter
Camera Power
Adapters
What you need
Althougheachsecuritysysteminstallationisdifferent,mostrequirethefollowingitemsnotincludedwithyoursystemcomponents:
• Toolstoinstallthecamerasandroutepowercables
-
8
SECTION 2: INSTALLING YOUR SYSTEM
• Fastenerstoattacheachcameratoitsmountingsurface•
AdisplaydeviceandcablingtoconnecttomonitortheDVR(exceptforSYRF204D-LCDsystems).TheDVRwillconnectdirectly
toaVGAvideomonitor,ortoaTVwithaBNCtoRCAadapterandRCAcable.Thedisplaydeviceisusuallyneededonlyforsystemsetup.ItcanbedisconnectedwhentheDVRisnetworkedforaccessacrossaLANorInternet.
•
Uninterruptiblepowersupply(UPS).Thisdeviceisusedtoensuresystemstabilityduringvoltagesurges,sags,andoutages.IfaUPSisnotavailable,apowerstripwithstrongsurgeprotectionishighlyrecommended.
2.2 Camera placement
Planyourcamerainstallationcarefully.Identifythelocationswherecameraswillprovidethebestcoverage,considering:
• Field of
view–Camerasmustbepositionedsotheycaneffectivelyviewtheentireareathatmustbemonitored,andinalocationthatmakestamperingwithitdifficult.
•
Lighting–Directsunlightshiningonthecameralensorbrightreflectionsfromshinyobjectsinthefieldofviewcandiminishvideoqualityandcameraperformance.Mountthecamerainshadedareas,ifpossible,orwheretheseinfluencescanbeminimized.
• Ease of
installation–Mustbeabletoinstallthecameraatthelocation,consideringmountinghardwarerequirements,temperature,dust,moisture,etc.
• Camera and DVR
spacing–TheminimumspacingguidelinesbetweenthewirelesscamerasandtheDVRshownbelowwillensurethebestperformanceofyourwirelesssystem.Camerascanbeasfaras325feetfromtheDVR(lineofsight,unobstructed).
> 16.5 ft
> 16.5 ft
> 10 ft
> 10 ft
> 10 ft
> 10 ft
> 16.5 ft
> 16.5 ft
Minimum distances between system components
•
PAIRing–ConsideringwallsandotherobstructionsthatmightexistbetweenthebestplacementofthecameraandtheDVR,theymustbeablesynchronize(PAIR)witheachother.
-
94-Camera Digital Wireless System Setup Guide
SECTION 2: INSTALLING YOUR SYSTEM
About weatherproof cameras
Weatherproofcamerascanbemountedinanyopenarea,suchasonatelephonepoleoronthesideofabuilding.However,forbestresults,werecommendyoumountyourcamerasinashelteredarea,suchasundertheeaveorroofofabuilding.Pointthecamerainthedirectionyouwishtoobserve.Whenroutingcablenearthecamera,allowenoughslacktoformaU-shaped“driploop”tohelpdirectmoistureorrainwater,thataccumulatesonthecable,awayfromthecamera.
Drip Loop
Drop Cable
NOTE Cable connections are not weatherproof.
Powercablescanberunalmostanywhere,andarefrequentlyroutedthroughatticsorabovedrop/acousticceilingsbecauseoftheeaseofinstallation.Foraddedsecurity,werecommendyourunyourcablesinareaswithlimitedaccesstopreventtampering.Avoidrunningthecablenearhighvoltageappliancessuchasfluorescentlighting.Electricalnoiseandmagneticfieldsproducedbythesedevicesmayaffectvideosignalquality.
2.3 DVR placement
Yourmonitoringandrecordingequipmentiscentraltoconstantsurveillanceandthereliablecaptureofvideoevidence.Westronglysuggeststhatitbeinstalledinasecurelocationwithaccesslimitedtoauthorizedpersonnel.
DVRsgenerateheatandshouldbeinaventilatedarea.Ahightemperatureenvironmentwillreducethelifespanandreliabilityoftheequipment.Additionally,theDVRisnotweatherproof,soavoidexposuretoliquidsandexcessivedust.DonotplaceobjectsalongthesidesorbehindtheDVRthatwillblockairflowthroughtheunit.
-
10
SECTION 2: INSTALLING YOUR SYSTEM
2.4 DVR Installation
1.
PlaceyourDVRonaclean,flat,horizontalsurfaceinlocationcharacteristicofthatdescribedabove.
2.
Installandsetupyourmonitorinaccordancewiththeinstructionsprovidedwiththemonitor.Donotpoweritonatthistime.
3.
CabletheDVRmainout(VGA)connectortoyourmonitor’sVGAinput.YoucanalsousethemonitormainoutBNCinterface,butthesignalqualityisbetterthroughtheVGAinterface.
NOTE Some monitors have multiple inputs including VGA ,HDMI,
BNC, etc. If you are using this kind of monitor, configure your
monitor to display the input from your DVR.
Wireless antenna SMA connectors (CH1 - CH4)
LAN
Main Out (BNC)
Power Switch
Sensor In/Alarm Out, RS485 connections
Main Out (VGA)
USB ports
Power DC 12V
4.
PlugtheUSBmouseprovidedintotheUSBmouseconnectoronthebackoftheDVR.
NOTE At this time, you can connect sensors (not provided) to the
sensor and ground terminal block on the back of the DVR, if needed.
You can also attach an alarm output (reporting) device to the same
terminal block. For additional information, see section 1.2.2 above
or contact your DVR support organization for specific
instructions.
NOTE Do not connect a LAN drop cable to your DVR at this time.
Refer to “Networking your DVR” later in this manual.
5.
Attachthe4antennasprovidedwiththeDVRtothefourSMAconnectorsonthebackoftheDVR.Orientthemsotheyarevertical.
6.
SlidetheINPUTSELECTswitchesforCH2andCH4totheRFposition(left).
7.
PlugtheDVRpoweradapterprovidedwithyoursystemintotheDV12VconnectoronthebackoftheDVR,andintoastandard120VACoutlet.
8.
PoweronyourDVRbysettingthepowerswitchonthebackoftheunittoON(position“1”).
-
114-Camera Digital Wireless System Setup Guide
SECTION 2: INSTALLING YOUR SYSTEM
9.
Poweronyourmonitorandconfigureit,ifnecessaryfortheinputyouareusingforyourDVR.AftertheDVRinitializes,theinitialscreenonthemonitorwillbesimilartothatshownbelow.
Theaboveimageisdividedintofourquadrants,oneforeachcamerachannel.Theupperrowquadrantsareassignedtochannels1and2,lefttoright.Thelowerrowquadrantsareassignedtochannels3and4,lefttoright.
2.5 Camera installation
Whereveracameraislocated,itmustbeabletoPAIRwiththeDVR.Beforemountingthecamera,testthecameraandDVRtoassurethatgoodqualityvideocanbeseenonthesystemmonitor:
1.
AttachtheantennaprovidedwiththecameratotheSMAconnectoronthebackofthecamera.
2.
Positionthecamerainlocationwhereyouwanttoinstallit,thenplugthepoweradapterprovidedwiththecameraintothecamerapowerdropcableandintoastandard120VACoutlet.
3.
Afterashorttime,verifythatcameravideocanbeseenontheDVRmonitor.Intheexamplebelow,thecameratestedwassetupforchannel2..
-
12
SECTION 2 INSTALLING YOUR SYSTEM
4. Disconnectpowerfromthecameraandsetitaside.
5.
Assemblethecameramountingbracket(shippedin3pieces)asshownbelow.
Rubberwasher
Gimballockknobr
6.
Anchorthemountingbracketatthecameralocationusingfastenersthatareappropriateforsurfacematerial.Thescrewsandwallinsertsprovidedwiththecameraareusefulformanytypesofsurfacematerials.
7.
Attachthecameratothemountingbracket.Makesurethattherubberwasherprovidedisplacedovertheboltandbetweenthebracketandthecamera.
8. Reapplypowertothecamera.
9.
ViewvideofromthecameraontheDVRmonitor,thenloosenthegimballockknobandaimthecameraatthepreferredfieldofview,ifnecessary.Tightenthegimballockknob.
10.
Repeatthisprocedurefortheothercamerasyouareinstalling.Youshouldseevideofromeachcamera.
-
134-Camera Digital Wireless System Setup Guide
SECTION 2 INSTALLING YOUR SYSTEM
Note:Theimagesyouseefromyourcamerasmaybedifferentfromthoseshownhere.
-
14
SECTION 3: DVR SETUP
SECTION3 DVR
SetupSettingupyourDVRincludesloggingintoyourDVR,settingtheclock,settingadministratoranduseraccountpasswords,andsettingupscheduledand/orautomatedmotionrecording.
3.1 Login to the DVR
Twoaccessaccountsarepresetinyoursystem:Adminanduser1.WiththeAdminlogin,youcanmakeconfigurationchangestothesystem,createuseraccountsandpasswords,andcontroltheprivilegesallottedtoeachaccount.Withthefactorydefaultuser1accountloginyoucannotmakeconfigurationchangesorcreateaccounts,butcanchangeyourownpassword.ThefactorydefaultAdminanduser1accountpasswordsare:
Admin: 888888 user1: 666666
Tologintothesystem:
1.
PowerontheDVRandwaituntilitadvancestothecameraviewscreen.Atypicalcameraviewscreenisshownbelow.
NOTE During initial startup of the system, no password is
required.
Camera Channel Number
2.
PresstheMENUbuttononthefrontpaneltwice,orright-clickthemousetwiceanywhereonthescreen.AnInput
Passwordwindowwillappear.
-
154-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
Confirm entry
3.
ClicktheqiconstotherightoftheUserNamefieldparameterfieldandselectAdmin.Tomakeconfigurationchangestothesystem,youmustlogintotheAdminaccount.
4.
Usingthemouse,clicktheentryfieldonthePASSWORDline,thenclickthenumberbuttonsthatappeartoentertheaccountpassword.Forexample,toenterthedefaultAdminpassword,888888,clickthe“8”buttonsixtimes.
5.
Clickthea(checkmark)iconinthelowerrightcornerofthewindowtoconfirmyourentryandenterthelogininformation.Atoolbariconstripwillappearatthebottomofthescreen.
3.2 Configuring the system
Basicsystemconfigurationsettingsincludesettingthescreenlanguage,videosystemformat,systemtime,creatingusers,initializingtheharddiskdrive(HDD),andsettingupautomatedrecording.
1.
Ifthesystemisnotrunning,powerontheDVRandwaituntilitcompletesinitialization.
2.
Right-clickanywhereonthedesktop,orpresstheMENUbutton.Astatusbarwillappear.
3.
ComparetheDVRsystemdateandtimeshownontheStatusBarwithanaccurateclock.
System Date and Time Remaining HDD Recording TIme
Status Bar
Note:Toseeanaccurateclock,accessareliableInternettimeserver,suchastf
.nist .gov
4.
Right-clickthemouseanywhereonthescreenagain.TheStatusbarwillchangetoaToolsBaroraloginwindow.IfaLOGINwindowopens,logintothesystemasanAdmin(seeabove).
-
16
SECTION 3: DVR SETUP
System Settings EZoomPTZ
Play
Manual Record / Stop Manual Record
Auto Sequence VGA - BNC switch
Advance
Keylock
Tool Bar
5. ClicktheSettingsbuttonontheToolBar.
3.2.1 Settingthescreenlanguageandvideosystemformat
1.
IntheSettingswindowSYSTEMtab,clicktheqiconattherightendoftheLANGUAGEline.Select(click)thescreenlanguageyoupreferfromthedropdownlist.
2. IftheVIDEO
SYSTEMoptiondoesnotindicateNTSC,clicktheqiconattherightendoftheVIDEO
SYSTEMline,thenselectNTSCfromthedropdownlist.
3.2.1 Settingthesystemtime
1. OntheTIMEline,clickthe>>icontoopentheTIME
SETUPwindow.
-
174-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
2. ClicktheqiconattherightendoftheDATE
FORMATline.Selecttheformatyouprefer:MM/DD/YY,YY-MM-DD,orDD-MM-YY.
3.
ClicktheentryontheDATEline.Clickthetoruiconstohighlightadigitofthedate,thenclickthenumbervalueofthedigitTocompletetheentryandclosethevirtualkeyboard,clickthe=button.
4. ClicktheqiconattherightendoftheTIME
FORMATline.Selecttheformatyouprefer:12houror24hour.
5.
ClicktheentryontheTIMEline.Clickthetoruiconstohighlightadigitofthecurrenttime,thenclickthenumbervalueofthedigit.Tocompletetheentry,clickthe=button.
6.
Ifyouselecteda12hourtimeformat,clicktheqicononthelinebelowtheTIMEentry,thenselecteitherAMorPM.
7. OntheDSTline,clickthe>>
icontoopentheDST(ON/OFF)optionwindow.IfyouselectON,aDSTsetupwindowwillopen.UsethemethodlikethatdetailedabovetosetuptheDSTstartandendtime,thenclicktheconfirmentrycheck(a)inthelowerrightcornertoconfirmyourentries.
8. ClicktheCONFIRMbuttonintheNOTEwindow.
-
18
SECTION 3: DVR SETUP
3.2.2 ChangetheAdminanduser1passwords
ChangingthedefaultAdminanduser1accountpasswordsfromtheirinitial(default)valueaddssecuritytoyoursystem.Thefactorydefaultaccountnamesandtheirpasswordsare:
Admin: 888888 user1: 666666
Tochangethesepasswords:
1.
Withthesystempoweredon,rightclicktwiceonthedesktoporpressthemenubuttononthefrontpaneltwice,thenlogintothesystemastheAdmin(ifapasswordloginisrequired).
2.
ClicktheSettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
3. OntheUSERline,clickthe>>icontoopentheUSER MANAGEMENT
window.
4. OntheCHANGE PASSWORDline,clickthe>>icontoopentheCHANGE
PASSWORD window.
-
194-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
5. ClicktheqiconattherightendoftheUSER
NAMEline.Fromthedropdownlist,selectAdmin .
6.
ClicktheOLDPASSWORDentryfield,thenenterthecurrentAdminpasswordusingthevirtualkeyboard.
7. EnterboththeNEW PASSWORDandCONFIRM
PASSWORDfieldswithadifferentpassword.Passwordscannotbemorethan6digitsinlength.
8.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNote
window.
9. Repeatsteps3,4,5,and6abovetochangetheuser1password.
3.2.3 Adduserstothesystem
1. OntheSYSTEMtabUSERline,clickthe>> icontoopentheUSER
MANAGEMENT window.
2. IntheUSER MANAGEMENT window,clickthe>>
iconontheADDUSERline.
3. ClicktheentryfieldontheUSER
NAMElinetoopenavirtualkeyboard.Clickthelettersandnumberstoenterausername,thenclickthe=icontoclosethekeyboard.
4. EnterboththePASSWORDandCONFIRM
PASSWORDfieldswithapasswordfortheuser.Passwordscannotbemorethan6digitsinlength.
5.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
6.
PresstheMENUbuttononthefrontpanelorrightclickonthedesktoptoreturntotheUSERMANAGEMENTwindow.
7. IntheUSER MANAGEMENT window,clickthe>> iconontheSET
PERMISSIONSline.
-
20
SECTION 3: DVR SETUP
8. ClicktheqiconattherightendoftheUSERS
line.Fromthedropdownlist,selectthenameoftheuseryoujustcreated.
9. ClicktheOPTcheckboxestoassignpermissionstothenewuser.
10.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
11. IntheUSER MANAGEMENT window,clickthe>>
iconontheREMOTEline.
12.
Click(check)theoptionsyouwanttheassigntotheuser,thenclicktheconfirmicon(a)inthelowerrightcornerofthescreen.ClicktheConfirmbuttonintheNotewindow.
13. Similarly,intheUSER MANAGEMENT window,clickthe>>
iconontheVIEWline.Click(check)thecamerachannelsyouwanttoallowtheusertosee,thenclicktheconfirmicon(a)inthelowerrightcornerofthescreen.ClicktheConfirmbuttonintheNotewindow.
14.
PresstheMENUbuttononthefrontpaneltoreturntotheUSERMANAGEMENTwindow,thenpresstheMENUbuttonagaintoreturntotheSETTINGSwindowSYSTEMtab.
3.2.4 SetHDDoverwriteoption
1. OntheSYSTEMtabHDDline,clickthe>> icontoopentheHDD
MANAGEMENT window.
-
214-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
2. ClicktheqiconattherightendoftheOVERWRITE
line.Fromthedropdownlist,selecttheoptionyouprefer:
—
Close:WhentheHDDbecomesfull,noadditionalrecordingsarewrittentotheHDD—
Overwrite:RecordingsontheHDDareoverwrittenwhentheHDDbecomesfull.Theoldestrecordingisoverwritten
first.— 1 HOUR . . 90
DAYS:Recordingsareoverwrittenwhenolderthanthetimeselected.
3.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
4.
PresstheMENUbuttononthefrontpanelorclickonthedesktoptoreturntotheSYSTEMtab.
3.3 Record configuration settings
Therecordingsettingsofeachcamerachannelcanbespecifiedseparatelyorcollectively.Thesesettings,includingtherecordingscheduleforeachchannel,aresetupthroughtheRecordtab.
1.
ClicktheSettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
2. ClickRECORDtoopentheRECORDsettingsmenu.
-
22
SECTION 3: DVR SETUP
3. ClicktheqiconattherightendoftheCHANNEL
line.Fromthedropdownlist,selectthenumberofthecamerachannelyouwanttosetup,orselectALLtoconfigureallchannelswiththesamesettings.
4. ClicktheqiconattherightendoftheRECORD
line.Fromthedropdownlist,selectDISABLE,orENABLEtorecordvideofromthechannel.
5. ClicktheqiconattherightendoftheBITRATE
line.SelectGOOD,NORMAL,orLOW.AGOODbitrateproducesthebestrecordingquality,butusesmoreprocessingpowerandharddiskspace.
6. ClicktheqiconattherightendoftheRESOLUTION
line.Fromthedropdownlist,selectD1(720×486),HD1(720×240),orCIF(352×288).
7. ClicktheqiconattherightendoftheFRAME RATE
line.Fromthedropdownlist,selectanumberbetween1and30(framespersecond).Thehighertheframerate(30fps),thesmootherthevideomotion.However,higherframeratesconsumestoragespacefaster.
8. ClicktheqiconattherightendofthePACKTIME
line.Fromthedropdownlist,selecteither15,30,45,or60(minutes).Packtimeisthetimelengthofvideofilesegmentsthatareoff-loaded(backedup).
9. ClicktheqiconattherightendoftheRECORD MODE
line.Fromthedropdownlist,selecteitherALWAYSorSCHEDULE.ALWAYScausestheDVRtorecordcontinuously.SelectingSCHEDULEallowsyoutoopenawindowtoconfiguretheDVRtorecordbythehourofthedayanddayoftheweek,eitherbymotionsensing,continuousrecording,ornotrecording.SeeScheduledrecordingbelow.
10.
Ifyouareconfiguringthecamerachannelsdifferently,repeatthisprocedurefortheothercamerachannels.
Scheduled recording
IftheRECORDMODE-SCHEDULEisselected:
1.
Clickthe>>iconontheRECORDtabtoopentheRECORDSCHEDULESETUPwindow.
-
234-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
2. ClicktheqiconattherightendoftheCHANNEL
line.Fromthedropdownlist,selectthechannelnumbertoapplytherecordingscheduleto,orselectALLtoapplythescheduletoallcameras.
3.
Atthebottomofthewindow,clickeithertheMD(motiondetection)orNORMAL(continuousrecording)checkbox,thenclickaboxinthetimearraytoapplythatmethodofrecordingtothattimeslot.
Intheexampleabove,NORMALrecordingwasscheduledforMondaythroughFridaybetween7AMand6PM.MDrecordingwasscheduledforMondaythroughFridaybetween4AMand7AMandbetween6PMand9PM,andonSaturdayandSundaybetween4AMand9PM.
4.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
5.
Ifyousetuptherecordscheduleforasinglechannel,repeatthisproceduretosetuptheothercamerachannels.
6. PresstheMENUbuttononthefrontpaneltoreturntotheRECORDtab.
3.4 Video configuration settings
Thevideoconfigurationsettingsaffecttheappearanceofthecameravideoonthemonitor.Theconfigurationcanbesesetupforeachindividualcamera,orthesamesettingscanbeappliedtoallcameras.
1.
ClicktheSettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
2. ClickVIDEOtoopentheVIDEOsettingsmenu.
-
24
SECTION 3: DVR SETUP
3. ClicktheqiconattherightendoftheCHANNEL
line.Fromthedropdownlist,selectthenumberofthecamerachannelyouwanttosetup,orselectALLtoconfigureallchannels.
4.
Initially,camerachannelsarenamedCH1..CH4.YoucanchangethenameofthechannelbyclickingontheentryfieldontheNAMElinetoopenavirtualkeyboard.Usethekeyboardtoenteranewname,ifneeded,thenclickthe=buttontoclosethekeyboard.
5. ClicktheqiconattherightendofthePOSITION
line.ThepositionoptionselectswherethecamerachannelNAMEappearsonthelivedisplay.Chooseoneoftheflowing:U-L(upperleft),D-L(lowerleft),U-R(upperright),orD-R(lowerright).
6. ClicktheqiconattherightendoftheLIVE
line.Inthedropdownlist,selectON(toviewvideofromthecameraontheLivescreen),orOFF.
7. OntheCOLORline,clickthe>>icontoopentheCOLOR SETUP
window.
TheCOLORSETUPwindowissuperimposedonthevideoimagefromthecamerachannelyouselected.AdjustthemarkersfortheHUE,BRIGHTNESS,CONTRAST,andSATURATIONtoproducethebestpicturefromthecamera.
8.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
9.
Ifyousetuptherecordscheduleforasinglechannel,repeatthisproceduretosetuptherecordscheduleforotherchannels.
-
254-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
3.4.1 Videosetup
TheVIDEOSETUPmenuprovidesconfigurationsettingsforthemonitorscreenresolution,sequentialliveviewsettings,andvideoblocking.
1.
ClicktheSettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
2. ClickVIDEOtoopentheVIDEOsettingsmenu.
3. OntheVIDEO
SETUPline,clickthe>>icontoopentheVIDEOSETUPmenu.
4. ClicktheqiconattherightendoftheVGA
line.Selectoneoftheoptions:1024x768or1280x1024.NOTE:ChangingthissettingfromthecurrentvaluewillcauseaDVRrestart.
5. ClicktheentryfieldontheSEQUENTIAL
TIMEline,thenenteranumberbetween1and300(seconds).Thisoptionsetsthepausedurationwhensequentiallydisplayingthelivevideofromeachcamerainfullscreen.
Video blocking
Forsecurityorprivacyreasons,someareasofthevideofieldsofviewareblocked.Tosetuptheblocking:
1. IntheVIDEOSETUPmenu,clicktheqiconattherightendoftheCHANNEL
line,thenselectavideochannelnumberfromthedropdownlist.
2. OntheVIDEO SETUP / AREA
COVEREDline,clickthe>>icon.Videofromthecamerawillappearinfullscreenmode.
-
26
SECTION 3: DVR SETUP
3.
Blockareasofthevideoimagebypressingtheleftmousebuttonanddraggingtocreateaboxovertheareasyouwanttoblock.Inthefollowingimage,twoblockboxescoverwindowsforprivacy.
Privacy Blocks
Aftertheblockiscreated,itcanberepositionedbydraggingitwithamouse.
Toremoveablock,doubleclickonit.
4. RightclickanywhereonthedesktoptoreturntotheVIDEO
SETUPmenu.
5.
Clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
6. Repeatthisprocedurefortheothercamerachannels,ifnecessary.
3.5 Network configuration settings
UsetheNETWORKmenutoconfigureyourDVRforuseonaLAN,foraccessthroughtheInternet,foraccessfromasmartphone,andforissuingautomatedemailwhenalarmconditionsoccur.
-
274-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
RefertotheChapter4,Networking your
DVRforconfiguringyoursystemforlocalLANandInternetaccess.Forothernetworksettings,includingDDNS,EMAIL,MOBILE,andOTHERSETTINGS,refertothechapterDVR
System Menus.
NOTE The default IP addresses and port settings of your DVR may
be different from those shown in this document. Always use network
settings that are compatible with your network(s).
3.6 Alarm configuration settings
UsetheALARMmenutoconfigureyourDVRforbehaviorwhentheharddiskdrivebecomesfull,andformotiondetectionsensitivityofeachchannel.
1.
ClicktheSettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
2. ClicktheALARMtabtoopentheALARMsettingsmenu.
3. ClicktheqiconattherightendoftheDURATION
line.Fromthedropdownlist,selecteither30SEC..5MIN.Thisoptionsetstherecordingtimelengthafteranalarmrecordingisactivated.
4. ClicktheqiconattherightendoftheBUZZER
line.Fromthedropdownlist,selecteitherOFF,or5SEC..60SEC.Thisoptionsetsthebuzzersoundingtimewhenthealarmistriggered.
5. ClicktheqiconattherightendofthePRERECORD
line.Fromthedropdownlist,selecteitherOFFor5SEC.Thisoptiondisablesorenablesrecording5secondsofvideobeforethealarmoccurred.
6.
Clickthe>>iconontheEXCEPTIONlinetoopentheEXCEPTIONALARMmenu.
-
28
SECTION 3: DVR SETUP
7. Clickthe>>iconattherightendoftheHDD
FULLline.ThisfeatureenablesthebuzzersoundwhentheHDDisnearlyfull.SelecteitherOFF,1G(remaining),5G,10G,1HOUR,5HOUR,10HOUR,or20HOUR.
8. ClickthecheckboxtotherightoftheHDD
LOSSlabeltoenablethisalarm.WhentheHDDisnotavailable,thisfeaturewillsoundthebuzzerandplacethe
onthedesktop.
9. ClickthecheckboxtotherightoftheVIDEO
LOSSlabeltoenablethisalarm.Whenavideosignalfromachannelisnotdetected,thisfeaturewillsoundthebuzzerandplacetheVideo
LosslabelinthechannelLIVEviewwindow.
10.
Afterconfiguringyournetworksettings,clicktheconfirmicon(a)inthelowerrightcornerofthescreen,clicktheConfirmbuttonintheNotewindow.
11.
PresstheMENUbuttononthefrontpanel,orrightclickanywheretoreturntotheALARMmenu.
3.6.1 Motiondetectionsetup
Motiondetectioncanbeconfiguredforeachchannelindividually,oryoucanapplythesamesettingstoallchannelsatonetime.
1.
OntheALARMtabmenu,clickthe>>iconontheMOTIONlinetoopentheMOTIONDETECTIONmenu.
-
294-Camera Digital Wireless System Setup Guide
SECTION 3: DVR SETUP
2. ClicktheqiconattherightendoftheCHANNEL
line.Fromthedropdownlist,selectthecamerachannelnumberyouwanttosetup,orselectALLtoconfigureallchannels.
3. ClicktheqiconattherightendoftheSWITCH
line.Fromthedropdownlist,selectONorOFFtoenableordisablemotiondetectiononthechannel(s).
4. ClicktheqiconattherightendoftheSENSITIVITY
line.Fromthedropdownlist,select1..8tosetthelevelofsensitivity.1ishighest,8islowest.Highsensitivitymaycauseanalarmwhenasmallobject,suchasabirdormouse,passesthroughthefieldofview,whereasthelowestsensitivitylevelmaybeappropriatefordetectingonlycarsthatpassby.Thissettingisdependentonthewhatyouwanttodetect,andusuallyrequirestestingtofindthebestvalue.
5. Clickthe>>iconontheMD
AREAlinetospecifytheareaswhereofthescreenwheremotionshouldbesensed.Definingonlytheseareas(andignoringotherareas)ofthefieldofviewimprovestheperformanceoftheDVR.
TheMotionDetectionsetupscreenispartitionedintoagridof10x15blocks.Motionsensingineachblockcanbetoggledonandoffbyclickingtheblockarea.Initially,allblocksareshadedpurple,indicatingthatmotionsensingisdisabledeverywhere.
Todisableblocks(areas)formotionsensing,clicktheblock,orusethemousetodragarectangleoverareasyouwanttodisable.Theshadingwilldisappearforareasdeselectedtodetectmotion.
Motion Sensing Disabled
Motion Sensing
Enabled
-
30
SECTION 3: DVR SETUP
6.
Afterthemotionsensingareasareselected(shaded),rightclicktoreturntotheMOTIONDETECTIONSETUPmenu.
7.
ChecktheboxtorightoftheRECORDlabeltoenablerecordingwhenmotionisdetected.
8.
ChecktheboxtorightoftheBUZZERlabeltosoundthebuzzerwhenmotionisdetected.
9.
ChecktheboxtorightofthePRERECORDlabeltoaddtheprevious5secondsofvideofromthecameratothemotiondetectionrecording.
10.
ChecktheboxtorightoftheEMAILlabeltosendanemailwhenmotionissensed.Tousethisfeature,theEMAILconfigurationsettingsintheNETWORKtabmustbeconfigured.
11.
Afterconfiguringyourmotiondetectionsettings,clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
12. Repeatthestepsabovefortheothercamerachannels.
-
314-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
SECTION4 Networking Your
DVRYourDVRsupportshighlyflexiblenetworkingconfigurationsincludinganEthernetconnection,suchastoahomenetworkwithabroadbandrouterandmodem,andaPPPOEconnection.Inthissection,onlygeneralguidelinesforthesetupofaDVRonasimpleEthernetbroadbandhomenetworkareincluded.Ifyouencounterproblemsyoucannotresolve,contactyourdistributor.
Home networks
Atypicalhomenetworkincludesrouter,oneormorecomputers,andabroadbandmodemforaccesstoaninternetserviceprovider(ISP)andtheinternet.TheDVRattachestothenetworklikeacomputer,exceptthatithaspresetIPaddresssettingsthatmustbeconfiguredforyournetwork.
SettinguptheDVRonthehomenetworkrequiresconfiguringitwithIPaddresssettingsthatarecompatiblewithyournetwork,andconnectinganEthernetcablebetweentheDVRandtherouter.Oncesetup,yoursecuritysystemcanbemonitoredandcontrolledfromanycomputeronthenetworkwiththeMicrosoft®InternetExplorer(IE)browser.
-
32
SECTION 4: NETWORKING YOUR DVR
AftertheDVRissetuponyourhomenetwork,usuallytheroutercanbeconfiguredsothattheDVRisaccessiblefromacomputerontheInternetorfromasmartphone.Althoughmostroutersperformsimilarfunctions,thespecificprocedurestoconfigurethemvarywidely.However,thedocumentationprovidedwithyourrouter,withthegeneralguidelinesincludedhere,shouldenableyoutosetupyourDVRforwebaccess.
4.1 Configure the DVR for access on your home network
TosetupyourDVRonthenetworkwithoutconflictingwithotherdevices,configurethenetworksettingsofyourDVRbeforephysicallyconnectingittothenetwork.NetworkconflictsoccurwhentwodevicesonthenetworkhavethesameIPaddress.ThescreensshownhereweretakenfromaWindowsXPsystem:
1.
DeterminetheIPaddress,subnetmask,anddefaultgatewayofyourhomecomputer(PC)andrecorditinTable1.Togetthisinformation,dothefollowingattheWindowsdesktop:
a. OpentheWindowsStartmenuandclickRuntoopentheRundialogbox.
b.
TypecmdintheentryfieldandthenclickOKtoopentheDOScommandwindow.
c. Atthecommandprompt,enteripconfig
.ThePCwilldisplayEthernetdataassociatedwithyourEthernetadapterlocalareanetwork(LAN)connection.
Example: Typical use of ipconfig in Windows XP
-
334-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
d.
EntertheIPAddress,SubnetMask,andDefaultGatewayforyourPC’sEthernetadapterintoTable1.
NOTEThe Ethernet adapter data you see by using ipconfig will
probably be different from that shown in the example above. If you
are using Windows Vista or Windows 7, the IP address is identified
as the “IPv4 Address.”
Table1.PC/DVRnetworksettings
Computer (PC) DVR
IPAddress
SubnetMask
DefaultGateway
2. AtyourPC,findanIPaddressonyournetworkthatisnotinuse:
a.
WritedowntheEXACTIPaddressofyourPCuptothethird/lastperiod.Usingtheexampleshownaboveinthescreencaptureofipconfig,thisnumberwouldbe:192.168.1.
b.
Afterthethirdperiod,chooseanynumberbetween1and255thatisdifferentfromtheoneinyourPC’sIPaddress,168.Asafirsttry,let’schoose100,whichwillformtheIPaddress192.168.1.100.
c.
Next,usethepingcommandintheDOSwindowtoseeifthatIPaddressisinuseonyournetwork.Theformatofthepingcommandis:ping
Forthisexamplehere,weentered:ping 192 .168 .1
.100TotestyourIPaddress,enterping 192 .168 .1
.100.AnyreplyreceivedfromthepingindicatesthatadeviceonthenetworkisalreadyusingthisIPaddressandyoucanconnecttoit.
-
34
SECTION 4: NETWORKING YOUR DVR
d.
Examinethescreencaptureshownabove.Iftheresponsetothepingcommandwas“Request
timed out
.”likethatshownabove,usethisIPaddressforyourDVRIPaddress,enterintoTable1,skipstep2.eandcontinueatstep2.f.
Iftheresponsetothepingcommandwas“Reply from 192 .168 .1
.100:..”asshownbelow,adeviceexistsonthenetworkthatisusingthisIPaddress.Ifso,continueatstep2.e.
e.
Sincetheresponsetopingtestreturnedareplyasshownabove,trythepingwithanothernumberbetween1and255untiloneisfoundthatrespondswiththe“Request
timed out
.”message.UsethisIPaddresswithyourDVRandenteritintoTable1.
f.
Intable1,copythePC’sSubnetMaskandDefaultGatewayentriesintotheDVR’sSubnet
MaskandDefault Gatewaycells.
3. AtyourDVR,clicktheSystem
SettingsiconontheToolBar.TheSYSTEMtabwindowwillopen.
System Settings
4. ClickNETWORKtoopentheNETWORKsettingsmenu.
NOTE The default IP addresses and port settings of your DVR may
be different from those shown in this document. Always use network
settings that are compatible with your network(s).
-
354-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
5.
OntheNETWORKline,clickthe>>icontoopentheNETWORKSETUPmenu.
6. ClicktheqiconattherightendoftheTYPE
line.Fromthedropdownlist,selecteitherDHCP,PPPOE,orSTATICfortheIPnetworksetup.IfyouselectDHCPorPPPOE,theDVRwillacquireitsnetworksettingsautomatically.IfyouselectSTATIC,youcanconfigureyournetworksettingsmanuallybyclickingontheentryfieldandusingthevirtualkeyboardtoenterdata.Seethefollowingscreencapture.
-
36
SECTION 4: NETWORKING YOUR DVR
NOTE The MEDIA PORT, WEB PORT, and SETUP PORT numbers do not
need to be changed unless these ports are used by other devices on
your network.
7.
UsethevaluesinTable1toconfigureyourDVRwithaDNSaddress,IPADDRESS.SUBNETMASK,andGATEWAYaddress.Youcanalsouseanyothervaluesthatarecompatiblewithyourlocalnetwork.
8.
Afterconfiguringyournetworksettings,clicktheconfirmicon(a)inthelowerrightcornerofthescreen,thenclicktheConfirmbuttonintheNotewindow.
9.
PresstheMENUbuttononthefrontpanel,orrightclickanywheretoreturntotheSETTINGSmenu.
10.
AttheSETTINGSmenu,clicktheSYSTEMtab,thenclickthe>>iconontheMAINTENANCEline.
11.
Clickthe>>iconontheREBOOTline,thenfollowtheon-screenpromptstorebootyourDVR.
12.
ConnectanEthernetcablebetweentheLANportonthebackofyourDVRandanyopenportonyourrouter.
13.
AtyourPC,usethepingcommandwithyourDVR’sIPaddresstoconfirmthatyoucanconnecttoyourDVRfromyourPC.AttheDOSpromptintheCommandwindow,enter:ping
whereisthenewDVRIPaddress.Forexample,ifyourDVR’sIPaddressisnow192.168.1.100,enterping
192 .168 .1 .100
14. Examinetheresponsetothepingcommand.Iftheresponseis“Reply
from . . .”andNOT“Request timed out
.”asbefore,yourDVRisnowconfiguredonthenetwork.
-
374-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
4.1.1 VerifylocalnetworkconnectabilitywithIE
AfteryourDVRissetuponalocalnetwork,MicrosoftInternetExplorer(IE)isusedtoverifyconnectabilityacrosstheLAN.Italsoincreasesflexibilityformonitoringandconfiguringyoursecuritysystem.
BeforeyoucanconnecttotheDVRwithIE,the(default)securitysettingsinIEaremodifiedandanadditionalsoftwareisinstalled.
1. AtyourPC,loadIE.
2. OpentheIEToolspull-downmenuandselectInternet
Options.ClicktheSecuritytab.
-
38
SECTION 4: NETWORKING YOUR DVR
3. ClicktheCustom Level . .
.button.IntheSettingslist,changethefollowingsettingstoEnable:
— AutomaticpromptingforActiveXcontrols—
InitializeandscriptActiveXcontrolsnotmarkedassafeforscripting—
ScriptActiveXcontrolsmarkedsafeforscripting—
Binaryandscriptbehaviors— DownloadsignedActiveXcontrols—
DownloadunsignedActiveXcontrols— RunActiveXcontrolsandplug-ins
ClickOK,thenclickYESintheWarningwindow.
-
394-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
IntheInternet
Optionswindow,clickApply,thenclickOKtoclosethewindow.
NOTE If your computer operating system is Windows Vista or
Windows 7, User Account Control can interfere with the normal
operation of the DVR user interface. To disable UAC, open the
Control Panel > User Account > User Account window, clear the
Use User Account Control (UAC) to help protect your computer check
box, then click OK. A computer restart may be required.
4.
IntheIEURLfield,entertheIPaddressassignedtoyourDVRwiththeWEBPORTnumberconfiguredinyourDVR(intheexampleabove,thedefaultWEBPORTis8090).Usingtheexampleshownabove,enter:
192 .168 .1 .100:8090/
NOTE After sending the URL, IE may prompt you to load the
Chinese Simplified language pack. You can click Install or Cancel.
If you click Cancel, the message will reappear again when you
logout and login.
5.
DuringthefirstconnectiontotheDVR,asecuritywarningtoinstallsoftwareappears.ClickInstallandfollowtheon-screeninstructionstocompletetheinstallation.
-
40
SECTION 4: NETWORKING YOUR DVR
6. WhentheLoginscreenopensinthebrowser,entertheadministratorUSER
IDandPASSWORD,thenclickLogin.ThedefaultvaluesfortheadministratoraccountareAdminand888888.
7.
Afterlogin,theDVRwebdisplaywillappear.ToseeimagesfromthecamerasconnectedtoyourDVR,clicktheOpen
Allbuttoninthelowerleftcornerofthescreen.
-
414-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
NOTE
When viewing the DVR network browser interface, if the webpage
appears normal but the camera images are scrambled, check your
computer’s video adapter settings, or contact your distributor for
assistance.
4.2 Accessing your DVR from the Internet
TheremoteviewingcapabilitiesofyourDVRallowyoutoaccessandcontrolitfromanywhereintheworldviatheInternet.YourDVRmustbesetuponaLANbeforethiscapabilitycanbeenabled,andtheLANmusthaveahigh-speedconnectiontotheInternetforefficientdatatransfertooccur.ThisprocedurerequiresthatthenetworkrouterbeconfiguredforportforwardingtoyourDVR.Onlygeneralinstructionsforsettingupthiscapabilityareincludedhere.
NOTE For additional support for setting port forwarding, refer
to your product documentation or contact your distributor .
1.
ConfigureyourrouterforportforwardingtotheDVRusingthenetworkinformationincludedinTable1.Forinstructions,refertotheuserdocumentationforyourrouterand/ortheinformationandserviceprovidedathttp://portforward
.com.
Port forwarded for the DVR:
-
42
SECTION 4: NETWORKING YOUR DVR
CAUTION
By default, your DVR uses port 8090 for the web port, 9000 for
the Media port, 10510 for the Mobile server port, and 8000 for the
Setup port. If any of these ports are used by to another device on
your network, configure your DVR to use a different port. Do not
assign the ports used by your DVR for Web, Media, Setup or Mobile
to any other device on your local network. Also, when choosing a
port for port forwarding an Internet connection to your DVR, do not
use any of these ports, or other ports on your network already in
use.
2.
Determineifyourrouter/modemhasadynamicIPaddress(onethatcanchangearbitrarily,oftenusedbyinternetserviceproviders(ISPs)forcable/DSLmodems)orstaticIPaddress(unchanging).Ifyouareunsure,contactyourISPforthisinformation.IfyouuseadynamicIPaddressforyourmodem,gotostep4.
3. TofindthestaticIPaddressassignedtoyourLAN,gotohttp://www
.whatismyip
.com/fromaPConthesamenetwork(LAN)asyourDVR.TheIPaddressdisplayedistheIPaddressyouwillusetologinremotely.Keepthisinyourrecords.Skiptostep6.
Static IP Address:
4.
IfyouhaveadynamicIPaddress,itisconvenientandrecommendedtouseadynamicnameserverservice,suchashttp://www
.dyn
.com/(afreeservice),tosetuparemoteconnectionwithafixedhostnametoyourDVR.Tosetupanaccount,followtheinstructionsonthewebsite.
5.
WhetheryouhaveastaticIPaddress,oryousetupaDynaccountforadynamicIPaddress,thefollowingaredifferentwaystoviewyourDVRfromaPContheInternet:
a.
IntheURLfieldofyourInternetbrowser,enterthecurrentIPaddressofyourmodemwithrouterportnumber(portforwardedforyourDVR)assignedtoyourDVRintheformat:http://Forexample,iftheIPaddressofyourmodemis190.180.170.32andtheportforwardnumberis85,enter:http://190
.180 .170 .32:85
b. AccesstheDVRusingyourDynaccountandhostname.
-
434-Camera Digital Wireless System Setup Guide
SECTION 4: NETWORKING YOUR DVR
-
44
SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER
SECTION5 Accessing Your DVR With a Web
BrowserAfteryourDVRis“networked”forLANandInternetaccess,itcanbemonitoredandconfiguredremotely.Also,youcansearchforanddownloadvideoclipstoyourremotecomputer.TheexamplespresentedhereinaccesstheDVRthroughtheMicrosoftInternetExplorer(IE)browser.
5.1 Connecting to your DVR with IE
TherearedifferentwaystoconnecttoyourDVR,dependingonhowitisnetworked.
•
IfthecomputeryouareusingtoaccessyourDVRisonthesamelocalnetworkasyourDVR,youcanaccessitwithMicrosoftInternetExplorer(IE)usingplacingtheIPaddressandWebportoftheDVRintheIEURLfield.Forexample,theURLaddressHTTP://192.168.1.100:8090usesanIPaddressof192.168.1.100andawebportnumberof8090.
•
IfyouareaccessingyourDVRfromtheinternet,thenetworkmodem/routerwhereyourDVRisinstalledis77.67.214.84,andyourDVRisconfiguredontherouterportof2000,theURLforyourDVRwouldbeHTTP://77.67.214.84:2000.
•
IftheInternetServiceProvideryouareusingassignsadynamic(changing)IPaddresstoyourmodem/router(typical),youcanestablishafixedURLforyourmodem/routerusingaweb-basedservicesuchasDynDNS.com.Withthatservice,yourDVRmightbeaddressedasHTTP://JDSmithDVR.dyndns.com.
AfterconnectingtoyourDVRwithIE,aloginwindowwillappear.
-
454-Camera Digital Wireless System Setup Guide
SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER
IntheLoginwindow,enteraUSER
IDandPASSWORD,thenclickLOGIN.TheUSERID“Admin”hascompleteprivilegestomanagetheDVRremotely.ThedefaultpasswordforUSERIDAdminis“888888”.
5.2 Live screen
AfterloggingintoyourDVR,theLivescreenwillappear.TheLivescreendisplaysreal-timevideofromtheDVR.
Stop View
1-Channel View
4-Channel View
Full Screen
Snap
Record
Usingthebuttonsintherightframe,youcanstopviewinglivevideo,snapaphotoofoneofthevideochannels,orrecordvideofromallchannels.Youcanalsoviewallfourchannelsatthesametime(seeabovescreencapture),onlyonechannelonthescreen,orexpandonechanneltofillyourmonitorscreen.
• Stop View:ClicktheStopViewicontostopviewinglivevideo.•
Snap:ClicktheSnapicontocaptureaphotooftheselectedvideochannel.Toselectavideochannelonamulti-channel
display,clicktheimage.Theselectedchannelisframedwithablueborder.ThephotoissavedinJPGformatatthelocationshowninthepop-upwindow.
•
Record:ClicktheRecordicontorecordthechannelsdisplayed.Eachchannelisrecordedindividually.Recordingsaresavedinthelocationshowninthepop-upwindow.ThesevideofilesaresavedinAVIformat,andcanbeplayedwithanyAVIcompatibleplayersuchasHsPlayer(providedonthemini-CDwithyourDVR),VLCMediaPlayer,orWindowsMediaPlayer.
-
46
SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER
5.3 Replay window
TheReplaywindowenablesyoutoplayanddownloadrecordedvideo.Tousethisfeature:
1.
Inthecalendarframe,clickthedatewhenthevideowasrecorded.Inthefollowingexample,September15,2011wasselected.
2.
Fromthelistthatappears,clickthelabelforvideofileyouwanttoplayordownload.Thelabelsindicatethetimeofdaywhenthevideowasrecorded,thechannelthatwasrecorded,andthesizeofthevideoclip.
3.
ClickthePLAYbuttonatthebottomofthescreen.Usetheplaycontrolbuttonsbelowtheviewwindowtocontroltheplayback.
Todownloadthevideocliptoyourcomputer,clickDOWNLOAD.TheclipwillbesavedinthelocationspecifiedintheLOCALSETTINGscreen,thedownloadprogresswillappearatthebottomoftheviewwindow,andthepathandnametothevideofilewillbedisplayedwiththedownloadiscomplete.
4.
Clickonanotherfiletoplay,orclicktheTiconintheupper-rightcornertoclosetheReplaywindowbeforeselectinganotherscreenorwindow.
5.4 Remote window
TheRemotewindowallowsyoutoconfigureyourDVRfromyourlocalcomputerifyouloggedinwiththeAdminUSERID.Toexpandthemenutreeandopenaconfigurationmenu,clickthe“plus”boxtoexpandthetree,thenclickthemenuyouwanttosee.
-
474-Camera Digital Wireless System Setup Guide
SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER
TheoptionsonthesescreensareidenticaltothoseintheDVRmenusystem.RefertothechaptersInstalling
the SystemandDVR Menu
Systeminthisdocumentformoreinformation.AftermakingchangestoaRemotesettingmenu,clicktheSETUPbuttonatthebottomofthewindowtocommitthechanges.
ClicktheTiconintheupper-rightcornertoclosetheRemoteSettingwindowbeforeselectinganotherscreenorwindow.
5.5 Local setting
IntheLocalSettingwindow,youcanspecifythelocationsonyourcomputerwhereyouwanttosavetherecordings,frames,andfilesfromyourDVR.
-
48
SECTION 5: ACCESSING YOUR DVR WITH A WEB BROWSER
ClicktheTiconintheupper-rightcornertoclosetheRemoteSettingwindowbeforeselectinganotherscreenorwindow.
5.6 Logout
ClickingLOGOUTreturnsyoutotheUSERLOGINscreen.
-
494-Camera Digital Wireless System Setup Guide
SECTION 6: KWEYE SMARTPHONE APP
SECTION6 KWeye Smartphone
AppKWeyeisafreesmartphoneappforusewithyourmodelSYRF204Dsystem.Itsfeaturesinclude:
•
Compatiblewithmostmodelsofthesephones:AppleiPhone,iPad,andiPodTouch,GoogleAndroid,Symbian,WindowsMobile,Blackberry
• UnlimitedvideooncellularandWiFinetworks•
Supportsmulti-channelvideoencodersandPan,Tilt,andZoom(PTZ)controlledcameras•
Supportforauthentication•
Directstreamconnection(videodoesnotpassthrougha3rdpartyserver)•
Snapshotcapability(whileviewinglivestream)tosavetoyourlocalphotogallery•
Supportforlandscapeandportraitviews•
AbilitytochangeIPaddressandportasneededforinternalandremoteusers
ThisguideincludesinstallationanduseofKWeyewiththeAppleandGooglesmartphones.Formoreinformation,goto:
•
iPhone,iPad,andiPodtouch:http://itunes.apple.com/us/app/kweye/id412413785•
Androidphones:https://market.android.com/details?id=com.KWeye•
Forothersmartphones,contactyourproductdistributor
Tousethisapplication,yourDVRnetworkmustbesetuptoallowaccessfromtheInternet.
6.1 Installing KWeye
6.1.1 Installing KWeye in iPhone
KWeyecanbeacquiredfromtheiTunesApp Store >
Productivitygroup.ItcanbedownloadedandinstalleddirectlytoyouriPhone,ordownloadedintoacomputerwithiTunes,theninstalledonyouriPhone.BeforedownloadingapplicationsfromtheAppStoreyoumustcreateastoreaccount.
• TodownloadandinstallKWeyedirectlytoyouriPhone:—
ConnectyouriPhonetoahigh-speednetwork,suchasaWiFinetwork(toshortendownloadtime).—
OpentheApp StoreapplicationonyouriPhone,thensearchforkweye.—
DownloadandinstallKWeyeasyouwouldanyapplication.
-
50
SECTION 6: KWEYE SMARTPHONE APP
App Found Ready to Install Installed
• TodownloadKWeyetoyourcomputertheninstallitonyouriPhone:—
DownloadandInstallthelatestversionofAppleiTunesifnotalreadyinstalled.YoucandownloadiTunesfrom
ww .apple .com/itunes/Acomputerrestartmayberequired.—
OpeniTunes.— ClicktheiTunes
Storeiteminthelistontheleft,thenlogintoyouriTunesStoreaccount.Ifyoudon’thaveaniTunes
Storeaccount,followtheon-screeninstructionstocreateone.—
IntheSearchStorefieldintheupperrightcornerofthescreen,enterkweye
.
— AfterKWeyeisfound,clicktheFree
Appbutton,thenclickBuyinthepopupwindowtodownloadtheapplication.KWeyewillappearinyouriTunesLIBRARY>Appslist.
-
514-Camera Digital Wireless System Setup Guide
—
Afterdownloadingtheapp,attachyouriPhonetoyourcomputer,synctheapplicationtoyourphone.
6.1.2 Installing KWeye in Android
ToinstallapplicationsusingAndroidMarketperformthefollowingsteps:
— WithyourAndroidphone,gototheApplicationsmenuandopenAndroid
Market.— Searchfortheapplicationkweye—
Whentheapplicationisfound,clickontheKWeyeicontodisplaydetailsoftheapp.—
ToinstallKWeye,clickInstallandfollowtheon-screeninstructions.
6.2 Set up access to a DVR
UsageandfunctionalityoftheKWeyeappisthesameonbothiPhoneandAndroidphones.However,thescreensvaryslightlybetweenthetwosystems.TouseKWeye:
• TaptheKWeyeicon
toopentheapp.TheKWeyesplashscreenwillappear.(NOTE:ThefollowingimageswerecapturedfromanAndroidsmartphone.iPhonescreensarefunctionallyidentical.)
SECTION 6: KWEYE SMARTPHONE APP
-
52
SECTION 6: KWEYE SMARTPHONE APP
Settings
iPhone KWeye Initial Screen
Android KWeye Initial Screen
•
TaptheSettingsicon.ThesplashscreenwillchangetotheSettingsscreen.
• IntheDevice
Infofields,entertheappropriateinformationforyourDVR:
—
Address:IPaddressusedtoconnecttoyourDVRmodemfromtheInternet,ortheURLoftheDynDNSserveryouuse.
—
Port:MobilemonitorserverportnumberconfiguredintheDVR’snetworkmobilesubmenu.Thedefaultportnumberis10510.
— DeviceName:AnameyouusetoidentifyyourDVR.— UserName
andPassword:Entertheusernameandpassword
youusetologintoyourDVR.NOTE:YoumayhavetoslidethescreenuptodisplaytheUserNameandPasswordfields.
•
AftercompletingtheentriesintheSettingsmenu,taptheBackbuttontotestthesettingsandconnecttoyourDVR.WhenconnectingtoyourDVR,theDeviceInfosettingswillbeloggedintheHistoryscreenforeasyretrieval.
6.3 Using KWeye
• IfKWeyeisnotrunning,taptheKWeyeicon
toopentheapp.TheKWeyeHistoryscreenwillappear.
•
IntheHistoryscreen,taptheentryfortheDVRyouwanttoconnecttoopen.TheSettingsscreenwillopen.
• TousetheDevice
InfointheSettingsscreentoaccessyourDVR,taptheBackbuttonintheupperleftcorner.
-
534-Camera Digital Wireless System Setup Guide
SECTION 6: KWEYE SMARTPHONE APP
• TapthePlaybuttontostartwatchingvideofromtheDVR.
PTZ Controls: Direction,
Zoom, Iris, Focus
Play/Stop
Select ChannelSwitch Channel Group
SW InformationSnapshot Settings
• Toviewaparticularcamera,taptheSelect
Channelbuttonforthecamerachannel.Ifyouareconnectedtoan8-and16-channelsystemandthechannelbuttonisnotshown,tapaSwitch
Channel Groupicon(nextgroup, ,orpreviousgroup ),tochangetheSelect
Channelbuttonsuntilthechannelnumberisshown,thentapthebuttonforthechannel.
• Rotatethephone1/4turnforalandscapeviewofthechannel.
•
Torestoretheappcontrolbuttons,orientthephoneforaportraitview.
• Toexittheapplication,pressthesmartphoneHomeorBackbutton.
-
54
SECTION 7: DVR SYSTEM MENUS REFERENCE
SECTION7 DVR System Menus
ReferenceThissectionincludesadetaileddescriptionoftheDVRmenusystem.Itisincludedforreferenceonly.
7.1 Menu tree
Record
Tool Bar
Channel
Record
Bitrate
Resolution
Framerate
Packtime
AudioPacktime
Record ModeVideo
Channel
Name
Position
Live
AudioColor
Record Time
Margin
Video Setup
Device ID
Password
Add Users
Change Password
Delete User
Set Permissions
Remote
View
Network
Network
DDNS
Email
Mobile
IP Firewall
Other Settings
Alarm
PTZ
Output
Duration
Buzzer
Prerecord
Exception
MotionI/O Alarm
Motion
Channel
Protocol
Baud Rate
Data Bit
Stop Bit
MotionParity
Address
System Settings
Play
Manual Record
Keylock
Auto Sequence
PTZ
Ezoom
Advanced
VGA / BNC Switch
PIP 1x1
PIP 1x2
Language
Video System
Time
User
HDD
Maintenance
Information
System
-
554-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.1.1 ToolBar
TheToolBarprovidesiconsforaccessingmenufeatures.
System Settings EZoomPTZ
Play
Manual Record / Stop Manual Record
Auto Sequence VGA - BNC switch
Advance
Keylock
Tool Bar
Toolbariconfunctions:
System Settings:Opensthesystemconfigurationmenusystem.
Play:Search,playbackandbackuprecordedfiles.
Manual Record / Stop Manual
Record:Clicktostartorstopmanualrecording.
Keylock:Ifthepasswordisenabled,click“KEYLOCK”tologoutofthesystem.
Auto
Sequence:Clicktoenableauto-sequencing,thechannelswithimageswillbeinsequence:channel1,channel2,channel3,channel4,channel1.Channelswithoutimageswon’tappearinthesequence.Tointerruptautosequencing,pressanybuttonorclickthemousewhileinautosequencemode.
EZoom:Clicktoenterzoommode,thenclickleftkeyanddragtoselecttheareathatyouwanttomagnify.Rightclicktoexit.
VGA/BNC
Switch:ClicktoswitchthevideooutputoftheDVRfromVGAtoBNCorBNCtoVGA.
Advance:ClicktoopentheAdvancetoolbar.
PIP 1x2Hide Advance
PIP 1x1
-
56
SECTION 7: DVR SYSTEM MENUS REFERENCE
Hide Advance:ClosetheAdvancetoolbar.
PIP 1x1:Thisfeaturedisplaysasmallpictureinafullscreen.
PIP 1x2:Thisfeaturedisplaystwosmallpicturesinafullscreen.
7.1.2 Menuoptions
Tomodify/adjustsystemconfiguration,clicktheSystem Settings
iconontheToolMenu.
ClickingtheSystemSettingsiconopensawindowwith6tabs:System,Record,Video,Network,Alarm,andPTZ.ThesetabsprovidegeneralsystemsettingsforoperatingyourDVR.
Open Drop-down List or Switch Value
Save Button
Titlesofthemenulistitemsarelocatedontheleft,andthecorrespondingchangeableornon-changeablevaluesarerepresentedinthefieldstotheright.Youcan:
•
Selectthevaluesfromthelist(togglingthepresetdatabypressingthearrowsonthesideofthefield);•
Selectthevaluesfromthedrop-downlist(openthedrop-downlistbyclickingthedownarrowsonthesideofthefield);•
Inputtherequireddataafterenteringacustomizedwindowbypressingthe[>>]buttoninsomeofthefields;•
Familiarizeyourselfwiththeexistingnon-changeablesettings.
WhenenteringdataintothefieldsusingtheDVRfrontpanel,andwhenpositioningthemouseoverthem,ashortdescriptionofthesettingwillappearatthebottomofthewindow.
Severaltabshaveoptionsthatarespreadacrossmorethanonewindow.Youcanmovefromwindowtowindowbypressingthe“>>”button.
-
574-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.2 System menu
TheSystemmenu(seeabove)containsparametersforsettingthebasicconfigurationofyoursystem.itincludesthefollowingoptions:
7.2.1 Language
UsethisoptiontochangethelanguageoftheDVRmenutextandtheOn-ScreenDisplay.
7.2.2 VideoSystem
Setthesystemoutputtothecamerainput(PALorNTSC).Note:Thedevicewillrestartwhenyoumodifythecameramode.
7.2.3 TimeSetup
ClickTime[System
settings->System->Time]toopentheTimesetupmenu.
DATE:Setupsystemdateusingthenumberkeypad.
DATE
FORMAT:Clickthedownarrowtoswitchthedateformat.Options:YY-MM-DD,MM/DD/YY.
TIME
FORMAT:Clickthedownarrowtoswitchthetimeformat.Options:12HOURSto24HOURS.
TIME:Setupthesystemtimeusingthedirectionalbuttonsonthefrontpanelorwiththemouse.
DST:Daylightsavingtime.ONmeansDSTclockchangeisenabled.YoucansetupthestarttimeandendtimeofDST.Forexample,intherightfigureabove,thestarttimeisat02:00:00SundayofthefirstweekonJanuary.Similarly,setuptheendtime.
-
58
SECTION 7: DVR SYSTEM MENUS REFERENCE
Note:Afterchangingsettings,clickthe“check”(save)buttoninthelowerrightcornerofthescreen.
7.2.4 Usermanagement
ClickUser[System
settings->System->User]toopentheusermanagementsetupmenu.ThismenuallowsusertosetthedeviceIDfortheDVRandtochangethesystempassword.Afterturningonpasswordandclickingthe“check”buttoninthelowerrightcornerofthewindow,exitthesystemandloginagaintomanageotherusers.
DEVICE ID:TheDEVICEIDisafixedidentifier.Itcannotbechanged.
PASSWORD:Changethepassword.Thefollowingsettingscanbeconfiguredonlybyauserwithadministrativeprivileges.
ADD
USERS:Toaddnewuser,enteranewusernameandpassword.PasswordmustbeenteredinboththePasswordandConfirmPasswordfields.Passwordcannotexceed6digits.
-
594-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
CHANGE
PASSWORD:Selecttheusernamewhosepasswordyouwanttochange,thenentertheoldpassword,thenewpassword,andthenewpasswordagainintheConfirm
Passwordfield.
DELETE
USER:Inthiswindow,selecttheuseryouwanttodelete,thenclickthe“check”buttoninthelowerrightcornerofthewindow.
-
60
SECTION 7: DVR SYSTEM MENUS REFERENCE
SET
PERMISSION:Foreachuser,setthepermissionsforuseofthesystem.Permissionsinclude:Autosequence,ManualREC,Playback/Backup,Ezoom,PIP,Update/Reboot/Maintenance/Format/Default,etc.
REMOTE
PERMISSION:Thisfeaturemustbesetupifoperatingthesystemremotely.Onlyuserswithadminprivilegescansetotheruser’sremotepermissions.Thesepermissionsinclude:Record/Capture,Playback/Download,andSetting.Ifpasswordverificationisenabled(markedON,i.e.youmustloginwithapassword)youcansetupsevenuserpasswordsandanadministratorpassword.
Note:WhenPasswordisenabled,logintothesystemasanadmintomanageusersettings.Theadministrator’sname(Admin)cannotbechanged.Initially,twousersexist:AdminandUser1.ThedefaultpasswordforAdminis“888888”andthedefaultpasswordforUser1is“666666”.
Ifforgetyourpassword,youcanresetthepasswordbyshuntingthepinofblockJ17onmainboardfor5secondswhilethesystemisrunning.However,REMOVING
THE COVER OF YOUR DVR WILL VOID THE WARRANTY .
-
614-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.2.5 HDD
ClickHDD[System
settings->System->HDD]toopentheHDD(harddiskdrive)managementmenu.
STATE:TheHDDcanhaveoneofthreepossible“states”:OK,un-format,andNo
Disk.IftheHDDcannotoperatenormally(un-formatorNoDisk),aniconwillbedisplayedonvideoliveviewwindow.IfanewHDDisusedbytheDVRforthefirsttime,thesystemwillrestartaftertheHDDisformatted.
TOTAL/FREE:IndicatestotalspaceavailableontheHDD.
FREE TIME:IndicatesremainingrecordingtimeoftheHDD.
OVERWRITE:Includes:CLOSE,AUTO,1HOUR,3HOURS,1DAY,2DAYS,7DAYS,30DAYSand90DAYS:
CLOSE:therecordingstopswhentheharddiskdriveisfull.Itwillcontinuerecordingif“overwrite”isenabled.AUTO:therecordingcontinuesandoverwritespreviousrecordingswhenharddiskdrivespaceisfull.2
DAYS:arecordingsremainsontheHDDfortwodaysatmost.Aftertwodays,arecordingmaybeoverwritten.Otheroptions:Similartothe2DAYoption.
FORMAT HDD:
Movethecursortoselectthedevice,thenpressHDDtostartformatting.
FORMAT USB:ThisfunctionallowsyoutoformataUSBstoragedevice.
7.2.6 Maintenance
ClickMaintenance[System
settings->System->Maintenance]toopentheMaintenancesetupmenu.
-
62
SECTION 7: DVR SYSTEM MENUS REFERENCE
SYSTEM UPDATE: Toperformasystemupdate:
1. InsertathumbdriveintoaWindowsPCUSBport,then.
a. FormatthethumbdriveforaFAT32filesystem.
b. Createarootdirectoryonathumbdrivenamed“dvrupgrade”.
c. Copytheupdatefiletothe“dvrupgrade”directory.
d. EjectthethumbdrivefromtheWindowsPC.
2. InsertthethumbdriveintoaUSBportontheDVR,then:
a. Clickthe>>iconontheSYSTEMUPDATEline.
b. WaituntiltheDVRrecognizesthethumbdrive.
c.
PressEntertoupgradethefirmware.Theprogressofthesystemupgradewillbedisplayed.Aftercompletingtheupgrade,theDVRwillrestart.NOTE:Thesystemupgradeusuallyrequiresmorethantwominutestocomplete.
LOAD
DEFAULT:Restoresallthesystemconfigurationtothefactorysettings.
REBOOT:UsethisfunctiontorestarttheDVR.
POWER OFF:UsethisfunctiontopowerofftheDVR.
AUTO
MAINTAIN:WhenAUTOMAINTAINisON,youcansetatimeforsystemtoperformarestart.
-
634-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.2.7 Information
ClickInformation[System
settings->System->Information]toopentheInformationdisplay.Thisdisplayincludes:devicetype,softwareversion,releasedate,importparameterandexportparameter.
UseExportParametertosavethatinformationtoaUSBdisk.Parameterinformationmustbeexportedbeforeitcanbeimported(restored).
7.3 Record
ToopentheRecordmenu,movethecursortoRECORD(theiconwillbehighlightedwhenselected),thenpressEnter
. Youcanusethedirectionkeysandcursortochangetheoptions.
-
64
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.3.1 RecordChannel
Withthisoptionyoucanselectthecamera(channel)numberwhosesettingsyouwanttomodify.Ifyouwantthechangestoapplytoallavailablechannels,select“All”.Maketheselectionbypressingthearrowbuttons;theoptionsincludeCH1,CH2,CH3,CH4andALL.
7.3.2 Record
RecordENABLEindicatesthatthechannelisenabledforrecording.
7.3.3 Bit-rate
Therearethreeoptions:GOOD,NORMALandLOW,correspondingtoHIGHEST,HIGHandNORMALdatastreamstandard.Thebitrateofeachchannelrecordedcanbeadjustedindependently.
7.3.4 Resolution
RecordResolutionindicatesthesetupresolutionandcoderateforrecording.Therearethreeoptions:D1,HD1andCIFresolution.Theresolutionofeachchannelrecordedcanbeadjustedindependently.
7.3.5 FrameRate
Youcansettherecordingframerate(framespersecond,fps)forthecurrentchannel.Thehighertherecordframerate,thesmootherthemovementyouwillseeinplaybackmode.Theframerateofeachchannelcanbeadjustedindependently.
ForPALvideooutputformat,thedefaultsystemresolutionisCIF,andthedefaultframerateis25fpsforeachchannel.Withthissetting,thesystemwillrecord100fpswithallchannels.Theframeratecanbesetfrom1fpsto25fpsperchannel.
ForNTSCvideooutputformat,thedefaultsystemresolutionandframerateisCIF@30fps.Withthissetting,thesystemwillrecord120fpswithallchannels.Theframeratecanbesetfrom1fpsto30fpsperchannel.
7.3.6 Packtime
RecordPackTimeisthetimelengthofvideosegmentssavedduringthebackupofrecordedvideotoanexternaldevicewhenalarmrecordingisdisabled.Therearefouroptions:15min,30min,45min,and60min.
-
654-Camera Digital Wireless System Setup Guide
SECTION 7: DVR SYSTEM MENUS REFERENCE
7.3.7 RecordMode
Recordmodeincludestwogeneralcategories:ALWAYSandSCHEDULE.
ALWAYS:indicatesthattheDVRwillrecordthechannelselectedcontinuously.
SCHEDULE:Thissetupallowsyoutocreateaweeklyscheduleforrecording.ThisassuresthatonlyselectedeventsarerecordedontheHDD.Forexample,youmaysetupthesystemtorecordcontinuouslyduringbusinesshours,recordatlunchtimeonlywhenanalarmistriggered,andrecordatnightwhenmotionisdetectedand/oranalarmistriggered.NOTE:Manualrecordingcontinuesuntilstoppedbytheoperator.Itoverridesallsettings.
CHANNEL:Youcanselectallchannelsorjustonechannel.Therearethreemodesforrecording:ALARM,NORMALandNORECORD.Differentcolorsindicatedifferentrecordingmodes:Redindicatesalarmrecord,greenindicatesnormalrecord,grayindicatesnorecording.
Tosetupweeklyschedules,clickontheboxoftherecordingmodeyouwant(Alarm,NormalorNo
record),thenclickeachboxinthescheduletimelinethatyouwanttoapplythemodeto.Youcanalsoleftclickanddragaframeoverboxesinthescheduletimelinethatyouwanttoapplythemodeto.Youcanusethe[FROM-TO]pull-downmenusandCOPYbuttonsettingstorepeatsettingfromonedayt