-
Congratulations on your purchase of the Synergy N5 radio
controlled helicopter kit. The Synergy N5 was designed and
developed by Matt Botos in conjunction with a global
network of partners. The design of the Synergy N5 emerged from
many years of experience in the hobby including design, research
& development, and last but not least as a world
class pilot who truly enjoys this wonderful hobby.
This radio controlled helicopter is NOT A TOY. It is a
sophisticated piece of equipment and was designed and intended for
hobby use only. If not properly assembled, maintained or
operated, it is capable of causing property damage and bodily
harm to both the operator and/or spectators. Synergy Helicopters
Inc., its affiliates and its authorized distributors
assume no liability for damage that could occur from the
assembly or use/misuse of this product. If you are new to the hobby
we strongly recommend seeking the help and advice
from an experienced modeler.
Operation an model helicopter requires a high degree of
diligence and skill. If you are new to the hobby, it is best to
seek help and guidance from experienced radio controlled
helicopter pilots. This will both greatly speed up the learning
process and make it much safer for you.
For those pilots who will be operating their Synergy N5 in the
United States, we strongly recommend joining the AMA. The AMA is a
non-profit organization that provides services to the model
aircraft pilots. As an AMA member, you will receive a monthly
magazine entitled
Model Aviation and most importantly a liability insurance plan
to cover against possible accident or injury. All AMA charter
aircraft clubs require individuals to hold a current AMA
sporting license prior to operation of their models
For further information, you can contact the AMA at
Academy if Model Aeronautics5151 East Memorial Drive
Muncie, IN 47302(317) 287-1256
-
610-330 Fuel Tank
110-332 Fuel Clunk
110-333 Fuel Clunk Tubing
110-331 Fuel Tank Stopper
106-810 Fuel Tank Stopper Grommet
Complete Fuel Tank
Fuel Tank Assembly Bag #1
A1
Trim fuel tubing to 60mm or desired length
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Fuel Tank 12 N5 Fuel
Tubing Grommet 1
3 N5 Fuel Clunk Tubing 1
4 N5 Fuel Clunk 15 N5 Fuel Tank Stopper 1
-
A2
Landing Gear Assembly
Complete Landing Gear
101-308 M3x8 Button Head x4
610-320 Landing Gear Strut x2
610-322 Skid Tube Lock x4
610-321 Skid Tube x2
Bag #2
Screw Skid Tube Lock Downon to flybar then secure withinSkid
Tube
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Landing Strut 22 N5
Skid Tube 23 N5 Skid Tube Lock 44 M3 x 0.5 x 8 Button Head 4
-
Engine Clutch Assembly Bag #3A
A350 Sized Engine(not included)
610-1172 Fan Hub
100-312 M3x12 Socket Head
100-312 M3x12 Socket Head
Engine Nut(not included) See Note*
Engine Washer(not included)
610-171 Cooling Fan
101-306 M3x6 Button Head x4610-160 Clutch
108-110 8x12x12 One Way Clutch
M4x8 Socket Head x2
107-104 2mm Pivot Ball Long
100-252 M2 Nylock Nut
(Factory Installed)
*Fan Hub install note1. Slide Fan Hub on to crank shaft then
lightlytighten down engine nut so that there is noend play in
crank.(engine washer must be used!)2. Tighten down pinch bolts3.
Insert crank locking tool (not included) andfinish tightening
engine nut
ITEM NO. PART NUMBER DESCRIPTION QTY.1 OS50sxh 12 Servo Horn 13
N5 2mm Pivot Ball 14 M2 x 0.4 Nylock Nut 15 N5 Fan Hub 1
6 M3 x 0.5 x 12 Socket Head 2
7 N5 Cooling Fan 18 M3 x 0.5 x 6 Socket Head 49 N5 Clutch 1
10 M4 x 0.7 x 8 Socket Head 2
11 N5 One Way Clutch Bearing 1
12Engine Nut (Included with Motor)
1
-
Clutch Bell & Start Shaft Assembly
A4
106-326 26mm Hex Standoff x2
106-955 Hex Adapter
100-466 M4x6 Set Screw
610-162 Start Shaft
108-615 6x15x5 Radial Bearing
110-155 Clutch Bearing Block
108-105 10x19x5 Radial Bearing x2
610-120 20T Pinion Gear
610-157 Clutch Bell
108-614 6x12x4 Radial Bearing
110-158 Clutch Lining
Factory Installed
Factory Installed
Factory Installed
Install governor magnet before assembly
Bag #4
-
13.5
0
13.5
0
Servo Tray Module Assembly Bag #4A
A5
107-104 2mm Pivot Ball Long x6
610-210 Servo Tray Module
106-326 26mm Hex Stand off
Digital Servo(not included)
106-115 Servo Hold Down
100-212 M2x12 Socket Head x12
100-251 M2 Nut x6
Servo Horn
Servo Screw(included with servo)
Pivot Ball Mount DistanceFor optimal performance pivotballs
should be mounted between13.5mm and 14.5mm from the center of the
servo.
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 26mm Hex Stand Off 42
servo_tray 1
3 N5 Servo Hold Down 6
4 M2 x 0.4 x 12 Socket Head 12
5 N5 2mm Pivot Ball 6
6 M2 Nut 6
7 x x
8 x x9 x x10 x x
-
Heavy Duty Switch
106-326 26mm Hex Stand off x4
Servo Horn Screw
Switch Screws
Tail Servo
107-104 2mm Pivot Ball Long
100-251 M2 Nut
610-211 Radio Tray
106-115 Servo Hold Down x2
100-212 M2x12 Socket Head x4
Bag #4B
13.5
0
A616
.50
Radio Tray Assembly
Digital Mini Servo Only(not included)
100-212 M2x12 Socket Head x4
Servo Horn
107-104 2mm Pivot Ball Long
610-211 Radio Tray
100-251 M2 Nut
Servo Horn Screw
Throttle Servo Pivot Ball Spacing -Place pivot ball at 13.5mm
away fromthe center of the servo.
Tail Servo Pivot Ball Spacing-Place pivot ball 16.5mm away
fromcenter of servo.
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Radio Tray 1
2 N5 26mm Hex Stand Off 4
3 N5 Servo Hold Down 2
4 M2 x 0.4 x 12 Socket Head 8
5 N5 2mm Pivot Ball 26 x x7 x x8 x x9 x x10 x x
11 x x
12 x x
13 x x
-
100-306 M3x6 Socket Head 100-312 M3x12 Socket Head
110-226 Tail Bell Crank Block
610-313 Arc Brace x4
610-422 Canopy Stand Off
610-316 Motor Center Block
610-312 Frame Connector Block
110-420 Front Canopy Mount
100-310 M3x10 Scoket Head
100-306 M3x6 Socket Head
108-484 4x8x3 Flange Bearing120-122 Anti-Rotation Guide
610-223 3x26 Threaded Spacer
100-376 M3x16 Set Screw
101-308 M3x8 Button Head
Right Frame Support Installation
A7
610-310 Main Frame
100-308 M3x8 Socket Head
Flange oriented on outside of frame
Do not over tighten in plastic
Bag #5
-
100-308 M3x8 Socket Head
8x19x6 Radial Bearing Block Assembly
10x19x6 Top Radial Bearing Block Assembly
A8
Bag #5
106-326 26mm Hex Stand Off
610-142 Bearing Block
108-106 10x19x6 Radial Bearing
108-819 8x19x6 Radial Bearing
610-142 Bearing Block
Bearing Block Assembly & Installation
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Main Shaft Bearing
Block 2
2 N5 26mm Hex Stand Off 4
3 10x19x6 Radial Bearing 1
4 8x19x6 Radial Bearing 1
-
100-308 M3x8 Socket Head
Servo Tray & Radio Tray Installation
**Do not fully tighten screws**
A9
Bag #5
-
Idler Assembly
101-306 M3x6 Button Head
100-310 M3x10 Socket Head
106-930 M3 Step Washer
100-320 M3x20 Socket Head
610-319 Idler Brace
106-952 Governor Sensor Mount
Clutch Bell Assembly
610-317 Idler Mount
Install governor sensor at this time.
A10
Bag #6
X2
108-384 3x8x4 Radial Bearing
610-318 Belt Tension Idler
109-352 3x5x2 Brass Spacer
108-384 3x8x4 Radial Bearing
Clutch & Belt Idler Installation
-
101-306 M3x6 Button Head
610-317 Idler Mount Block
108-484 4x8x3 Flanged Bearing
610-323 Landing Gear Mount Block
100-310 M3x10 Socket Head
100-310 M3x10 Socket Head
Left Frame Side Assembly
610-310 Main Frame
Install Bearing Flange to outside of frame
A11
Step #1Bag #7
-
100-306 M3x6 Socket Head
100-306 M3x6 Socket Head
100-308 M3x8 Socket Head
610-323 Landing Gear Mount Block
610-323 Landing Gear Mount Block
100-310 M3x10 Socket Head
101-308 M3x8 Button Head
100-376 M3x16 Set Screw
610-422 Canopy Stand Off
100-308 M3x8 Socket Head
100-306 M3x6 Socket Head
100-354 M3 Washer
100-310 M3x10 Socket Head
Do not over tighten in plastic
Do not tighten bolts completelyuntil next step.
Left Frame Assembly
100-320 M3x20 Socket Head
Idler Assembly
100-306 M3x6 Socket Head
A12
Step #2Bag #7
-
90
Frame Alignment
With all bolts slightly loose, placeframeset on a flat surface.
Be surethat side frames are 90 degrees tothe flat surface. Once you
haveachieved the correct frame alignmentyou may finish tightening
frame bolts.
(Front view)
A13
-
Landing Gear & Fuel Tank Installation
Fuel Tank Assembly
106-807 Tank Edge Grommet
Landing Gear Assembly
100-316 M3x16 Socket Head
A14
Bag #7
-
Engine Installation
A15
50 Sized Motor
610-316 Motor Mount
M3x12 Socket Head
606-305 Motor Spacer
Bag #5
-
610-342 Fan Shroud Right
610-343 Fan Shroud Left
100-312 M3x12 Socket Head
100-210 M2x10 Socket Head
100-312 M3X12 Socket Head
Fan Shroud Installation
Do not over tighten!
A16
610-224 3x6x26 Threaded Frame Spacer
Bag #8
-
107-106 Short Pivot Ball108-483 4x8x3 Radial Bearing
610-221Bell Crank (Aileron & Pitch)
Bell Crank Assembly
Note orientation of boss before assembly of pivotball to bell
crank.
101-306 M3x6 Button Head
610-228 Bell Crank Spacer
610-225 Bell Crank Shaft107-106 Short Pivot Ball
100-364 M3x4 Set Screw
100-364 M3x4 Set Screw
610-222 Outside Elevator Bell Crank
610-226 Inside Elevator Bell Crank
Do not fix bell cranks to shaft untilthe next page where they
will fit intothe frame.
A17
X2
Bag #9
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Bell Crank Shaft 12 N5
Bell Crank AP 23 4x8x3 Bearing 44 N5 4.5 Pivot Ball 95 M3 x 0.5 x 6
Button Head 1
6 N5 Bell Crank Spacer 1
7 N5 Bell Crank Elevator Inside 1
8 N5 Bell Crank Elevator Outside 1
9 M3 x 0.5 x 4 Set Screw 2
-
Make sure set screws contactflat spots for both inside
andoutside elevator bell cranks!
Make sure there is no lateral movementin elevator bell crank
assembly. Pinch inside bell crank to outside bell crank then
tightenset screws.
101-306 M3x6 Button Head
Bell Crank Installation
A18
Note Bell Crank alignment holein frame for ease of correct
setup.
Bag #9
-
100-251 M2 Nut
107-104 2mm Pivot Ball
100-320 M3x20 Socket Head
108-373 3x7x3 Radial
109-355 3x5x5 Spacer
115-316 Tail Bell Crank
108-373 3x7x3 Radial
100-351 M3 Nylock Nut
615-317 Tail Lever Mount
106-301 M3 Shim
Step #2 Tail Box Assembly
Bag #10B
Step #1 - Tail Bell Crank Assembly
100-335 M3x35 Socket Head x5
101-306 M3x6 Button Head x4
108-514 5x13x4 Flange Bearing
610-224 3x6x26 Spacer
615-312 Tail Output Shaft
615-315 9T Tail Pulley
100-364 M3x4 Set Screw
615-320 Tail Belt
115-110 Main Boom Clamp
615-311 Tail Box Plate
Tail Box Assembly
A19
Tail Bell Crank Assembly
Bag #10A
-
Tail Box AssemblyStep #3
A20
100-351 M3 Nylock Nut
101-306 M3x6 Button Head
615-135 Vertical Tail Fin
108-514 5x13x4 Flange Bearing
109-357 3x5x7 Brass Spacer
108-384 3x8x4 Radial Bearing
109-357 3x5x7 Brass Spacer
615-316 Belt Tension Idler
Do not over tighten belt idler bolt
615-140 Tail Boom
Bag #10A
-
Tail Hub Assembly
A21
100-308 M3x8 Socket Head
100-354 M3 Washer
108-494 4x9x4 Radial Bearing
106-401 4mm Shim
108-495 4x9 Thrust Bearing
615-324 Tail Blade Grip
108-494 4x9x4 Radial Bearing
107-104 2mm Pivot Ball
615-323 Tail Rotor Hub
Use Medium CA to secure 2mm pivot ball
Bag #10C
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Tail Rotor Hub 12
4x9x4 Radial Bearing 43 N5 Tail Blade Grip 24 N5 2mm Pivot Ball 25
4x9x4 Thrust Bearing 26 N5 3mm Washer 27 M3 x 0.5 x 8 Socket Head
28 N5 4mm shim 2
-
Pitch Slider Assembly
615-318 Tail Pitch Slider Bushing
108-812 8x12x2.5 Radial Bearing
107-103 2mm Pivot Ball Short
115-319 Tail Bearing Ring
108-812 8x12x2.5 Radial Bearing
115-322 Tail Pitch Link
106-813 Tail Slider Lock Ring
606-921 Tail Pitch Link Pin
506-920 E-Ring
115-321 Pitch Plate
Use Medium CA to secure 2mm pivot ball
Bag #10D
1. After installing lock ring be sure that the radial bearings
do not have lateral loadon them. Adjust lock ring as needed to
ensure smooth operation. 2. Secure lock ring with CA or Epoxy
A22
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Tail Pitch Plate 12 N5
Tail Pitch Link 23 N5 Tail Pitch Slider Bushing 14 N5 Tail Bearing
Ring 15 N5 Tail Pitch Link Pin 26 N5 2mm Pivot Ball Short 1
7 8x12x2.5 Radial Bearing 2
8 Tail Slider Lock Ring 1
9 506-920 E-Ring 2
-
100-364 M3x4 Set Screw
Tail Pitch Slider & Tail Rotor Hub Installation
A23
Bag #10A
-
615-111 695mm Carbon Tail Control Rod
107-100 Ball Link
107-100 Ball Link
107-030 30mm Rod
107-030 30mm Rod
115-130 Horizontal Fin
100-320 M3x20 Socket Head
115-126 H. Fin Clamp Upper
115-125 H. Fin Clamp Lower
115-115 Guide Bushing
115-114 Tail Control Guide
Tail Push Rod & Guides
A24
Slide Tail Control Guide to approx. 265mmfrom the front of the
boom.
115-115 Guide Bushing is a tight press fit. We recommend using a
soft jaw vise or arbor press for installation.
Bag #10E
106-965 Tail Push Rod Sleeve
Approx. 5mm
Insert 30mm threaded rod approximately 17mm intocarbon tube. Use
Medium CA to glue threaded rodinto carbon rod.
-
115-110 Main Boom Clamp
100-351 M3 Nylock Nut x4
100-335 M3x35 Socket Head x4
Tail Boom Installation
A25
Slide belt and boom through main boom clampsuntil boom is flush
with second boom clamp. SecureM3x35 bolts.
Bag #10A
-
100-330 M3x30 Socket Head x2
101-410 M4x10 Button Head x2
115-119 Boom Support End x4
610-223 3x26 Spacer610-121 Boom Support Spacer x2
100-354 M3 Washer x2
Lightly sand carbon rod, use medium CA tosecure boom support
end.
Boom Support Assembly
A26
Bag #11
115-119 Boom Support End
109-345 3x4x5 Brass Spacer
615-117 Carbon Boom Support Rod
-
610-147 Auto Hub Sleeve
610-151 Auto Hub Delrin Shim
101-308 M3x8 Button Head
Auto Hub (Factory Assembled)610-149 12x22x3 Auto Hub Bronze
Bushing x2108-109 12x18x16 One Way Auto Hub Bearing HF1216610-148
Main Gear Auto Hub
610-151 Auto Hub Delrin Shim
610-146 Auto Hub Lock Collar
Main Gear/Auto Hub Assembly
Main Belt Pulley Assembly
A27
610-170 170T Main Gear
Bag #12A
610-143 Main Pulley Flange
610-141 Main Belt Pulley 42T
103-204 M2x4 Type I Cross Recessed
Bag #12B
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Main Gear Auto Hub
1
2 N5 Main Gear 0.7M 170T 1
3 12x18x16 One Way Clutch Bearing 1
4 M3 x 0.5 x 8 Button Head 4
5 N5 Auto Hub Bushing 2
6 N5 Auto Hub Delrin Shim 27 N5 Auto Hub Sleeve 18 N5 Auto Hub
Lock Collar 1
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Main Belt Pulley 42T
12 N5 Pulley Flange 2
3 M2 x 0.4 x 4 Cross Recessed 12
-
Twist Belt 1/4 Turn Clockwise.
Main Gear Assembly
Main Pulley Assembly
610-150 Main Shaft Collar
100-261 M2.5x10 Socket Head
610-140 Main Shaft
Drive Train Installation
Install main shaft with smalller8mm end pointing down.
A28
Bag #12C
-
100-325A M3x25 Shouldered Socket Head
100-320A M3x20 Shouldered Socket Head
100-351 M3 Nylock Nut x2
Gently push down on main shaft while pressingup on main shaft
collar. After tightening mainshaft collar ensure there is no
vertical play in the main shaft.
Drive Train Install Step #2A29
Bag #12C
-
Tail Linkage Assembly
A30
107-106 Pivot Ball
108-373 3x7x3 Radial
110-225 Tail Offset Bell Crank
106-301 3mm Shim
107-106 Pivot Ball
107-100 Ball Link
110-227 274mm Carbon Support Rod
107-295 295mm Tail Linkage Rod
107-100 Ball Link
109-352 3x5x2 Spacer
100-316 M3x16 Socket Head
108-373 3x7x3 Radial
Bag #13
Attention!If you are using an OS55HZ motorscrew the 107-106
Pivot Ball into the top of the Tail Offset Bell Crank. Thiswill
allow the Tail Linkage Rod to clearthe mid-range carb needle.
-
100-316 M3x16 Socket Head
108-383 3x8x3 Radial Bearing
108-383 3x8x3 Radial Bearing
109-352 3x5x2 Brass Spacer
107-106 Pivot Ball
106-301 3mm shim
620-210 Washout Hub
106-301 3mm Shim
100-316 M3x16 Socket Head
107-108 Long Pivot Ball
107-108 Long Pivot Ball
107-108 Long Pivot Ball
100-364 M3x4 Set Screw
120-214 Washout Link
606-923 Washout Link Pin
506-920 E-Ring
109-355 3x5x5 Brass Spacer
108-373 3x7x3 Radial Bearing
100-312 M3x12 Socket Head
107-106 Pivot Ball
100-310 M3x10 Socket Head
Swashplate and Washout Assembly
A31
620-213 Washout Control Arm
Bag #14
ITEM NO. PART NUMBER DESCRIPTION Default/QTY.1 N5 Outter Swash
Plate 12 107-108 Pivot Ball 33 N5 Inner Swash Ring 14 107-106 Pivot
Ball 45 N5 3x5x5 Spacer 16 3x7x3 Radial Bearing 1
7 25x37x7 Swash Bearing 1
8 N5 Spherical Plain Bearing 1
9 M3 x 0.5 x 4 Set Screw 1
10 N5 Washout Hub 111 N5 Washout Control Arm 212 N5 Washout Link
Pin 213 N5 Washout Link 214 3x8x3 Bearing 415 N5 3x5x2 Spacer 216
N5 3mm shim 217 N5 4.5 Pivot Ball 218 506-920 E-Ring 2
19 M3 x 0.5 x 16 Socket Head 2
20 M3 x 0.5 x 12 Socket Head 1
21 M3 x 0.5 x 10 Socket Head 1
-
Head Block Sub Assembly - Factory Assembled
620-118 Seesaw
108-383 3x8x3 Bearing
108-383 3x8x3 Bearing
101-308 M3x8 Button Head
106-301 3mm Shim
108-363 3x6x3 Radial Bearing620-110 Head Block
108-363 3x6x3 Bearing
106-301 3mm shim
101-308 M3x8 Button Head
606-922 2.5mm Washout Pin
106-363 3x6x2.5 Flange Bearing
106-363 3x6x2.5 Flange Bearing
100-308 M3x8 Socket Head
620-119 Flybar Control Arm
100-364 M3x4 Set Screw
620-123 Flybar 100-365 M3x4 Set Screw
100-308 M3x8 Socket Head
620-115 Head Button120-121 Flybar Control Arm Stand Off
107-106 Pivot Ball
109-351 3x5x1.6 Brass Spacer
Rotor Head Assembly
A32
X2
Bag #15
Bag #15
13m
m
107-100 Ball Link
107-100 Ball Link
107-030 30mm Rod
ITEM NO. PART NUMBER DESCRIPTION Default/QTY.1 N5 Head Block 12
3x6x2.5 Flanged Bearing 2
3 N5 Seesaw 14 3x6x3 Bearing 25 N5 3mm shim 26 M3 x 0.5 x 8
Button Head 27 3x8x3 Bearing 2
8 N5 2.5mm Washout Pin 2
9 N5 Flybar Control Arm 2
10 N5 FlyBar Control Arm Stand Off 211 N5 450mm Flybar 1
13 M3 x 0.5 x 4 Set Screw 2
14 N5 Head Button 115 N5 3x1.6x5 Spacer 216 N5 4.5 Pivot Ball
217 N5 Ball Link 418 N5 30mm Rod 2
-
108-816 8x16x5 Bearing
108-816 8x16x5 Bearing
106-803 8x1mm Washer
Smaller IDTight Fit on Head Axle
Larger IDLoose Fit on Head Axle
Apply Thick Grease to Thrust Bearing
620-112 Main Blade Grip
108-817 8x16x5 Thrust Bearing
Bag #16
Bag #16
100-512 M5x12 Socket Head
100-554 M5 Washer
(Thin) 106-801 8x.5mmWasher(Med.) 106-802 8x.75mmWasher(Thick)
106-803 8x1mm Washer
606-803 Solid Head Damper
620-113 Head Axle Sleeve
120-114 Head Axle
107-101 Short Ball Link
107-012 12mm Rod
107-101 Short Ball Link
100-318 M3x18 Socket Head
108-373 3x7x3 Bearing
109-356 3x5x6.5 Spacer
620-116 Bell Mixer
107-106 Pivot Ball
108-373 3x7x3 Bearing
107-106 Pivot Ball
Blade Grip Assembly
Rotor Head Assembly
Dampening OptionsAdd amount to Both sides Each Side of HeadLoose
= 1 ThickNormal = 1Thick, 1 ThinTight = 1 Thick, 1 Medium
DO NOT OVER TIGHTEN IN PLASTIC ARM
A33
Note: We recommend only using amount ofshims needed to take up
lateral play in bladegrips. Dampers are stiff enough to where
theywill not need much compression.
38m
m
ITEM NO. PART NUMBER DESCRIPTION QTY.1 N5 Main Blade Grip
Plastic 12 8x16x5 Bearing 23 8x16x5 Thrust bearing 1
4 106-803 8x1mm Washer 1
ITEM NO. PART NUMBER DESCRIPTION QTY.19 N5 Head Axle 120 N5
Solid Head Damper 2
21 N5 Head Axle Sleeve 1
22 106-803 8x1mm Washer 2
24 5 mm Washer 2
25 M5 x 0.8 x 12 Socket Head 2
26 Bell Mixer Assem 2 N5 Bell Mixer V2 1 N5 3x5x6.5 Spacer 1 N5
4.5 Pivot Ball 2 3x7x3 Radial Bearing 2
27 M3 x 0.5 x 18 Socket Head 2
28 Bell Mixer Linkage Assem 2
N5 Ball Link Short 2 N5 12mm Rod 1
-
Rotorhead to Swashplate Assembly
A34
X2
Bag #17
62
107-100 Ball Link
107-100 Ball Link
107-078 78mm Control Rod
-
100-320A M3x20 Shouldered Socket Head
M3 Nylock Nut
Rotorhead Installation
A35
X3
Ensure bolt travels through bothHead Block as well as the hole
in the main shaft. Make sure this bolt is securely tightened as it
pinchesthe head block onto the main shaft.
Bag #15 (Shouldered Bolt)Bag #17 (Linkage)
24
107-100 Ball Link
107-100 Ball Link
107-043 43mm Rod
-
Elevator Linkage
X2
A36Bag #17
Ap
pro
x. 5
8.50
mm
107-100 Ball Link
107-078 78mm Rod
107-100 Ball Link
-
Aileron Linkage
X2
Approx. 107
mm
107-100 Ball Link107-100 Ball Link
107-126 126mm Rod
A37
Bag #17
-
Pitch Servo Linkage
A38
Bag #17
Approx. 83mm
107-100 Ball Link
107-100 Ball Link
107-102 102mm Rod
X2
-
Throttle Linkage
A39
Appro
x. 85m
m
107-100 Ball Link
107-100 Ball Link
107-102 102mm Rod
Bag #17
-
100-435 M4x35 Shouldered Bolt
100-451 M4 Nylock Nut 100-366 M3x6 Set Screw
630-050 Flybar Paddle
110-418 Conopy Gromet
X4
Drill or ream the canopy mounting holesto 7.5mm before inserting
grommets. Makecertain holes are centered in the pockets.Use Medium
CA to secure canopy gromets to canopy.
Canopy, Blades, and Paddles
A40
610-400 Fiberglass Canopy
Bag #18
Tip - Push in while screwing the paddleon the flybar. Do not
over tighten paddleor set screw! The stock plastic paddles are very
good for smooth, medium agressive 3Dflight. If you want your cyclic
faster try alighter paddle or the inner hole on the
flybarcarrier.
100-316 M3x16 Socket Head
510-425 Canopy Thumb Screw
-
630-085 Plastic 85mm Tail Blade
100-316 M3x16 Socket Head
100-351 M3 Nylock Nut
Tail Blade Spacers
Tail Blade Install
A41
Bag #19
Suggested aftermarket tail bladelength between 85mm - 92mm.
Anythinglarger is not recommended and may voidthe warranty.
A0 - IntroductionSheet1
A1 - Fuel Tank AssemSheet1Drawing View1Drawing View2
A2 - Landing Gear AssemSheet1Drawing View2Drawing View1Drawing
View4
A3 - Engine - Clutch AssemSheet1Drawing View1Drawing
View2Drawing View3
A4 - Clutch Bell & Shaft AssemSheet1Drawing View1Drawing
View2
A5 - Servo Tray AssemSheet1Drawing View2Drawing View1Drawing
View3
A6 - Radio Tray AssemSheet1Drawing View1Drawing View3Drawing
View4Drawing View2Drawing View5Drawing View6
A7 - Right Frame Support AssemSheet1Drawing View1Drawing
View4Drawing View5Drawing View6Drawing View7Drawing View8Drawing
View9
A8 - Bearing Block Assembly & InstallSheet1Drawing
View1Drawing View4
A9 - Servo Tray & Radio Tray InstallSheet1Drawing
View1Drawing View2
A10 - Clutch & Belt Idler InstallationSheet1Drawing
View1Drawing View6Drawing View7Drawing View8Drawing View9
A11 - Left Frame Assembly Step #1Sheet1Drawing View1Drawing
View2Drawing View8Drawing View9
A12 - Left Frame Assembly Step #2Sheet1Drawing View1Drawing
View2Drawing View5Drawing View6Drawing View7Drawing View8Drawing
View9Drawing View10Drawing View11Drawing View12Drawing View13
A13 - Frame AlignmentSheet1Drawing View1
A14 - Landing Gear & Fuel Tank InstallSheet1Drawing
View1Drawing View2
A15 - Engine InstallationSheet1Drawing View1Drawing View2
A16 - Fan Shroud InstallationSheet1Drawing View1Drawing
View2Drawing View3
A17 - Cyclic Control AssemblySheet1Drawing View1Drawing
View2Drawing View13Drawing View14Drawing View15Drawing
View16Drawing View17
A18 - Bell Crank InstallationSheet1Drawing View1Drawing
View2Drawing View3Drawing View4
A19 - Tail Assembly Step 1-2Sheet1Drawing View1Drawing
View2Drawing View3Drawing View4Drawing View5
A20 - Tail Assembly Step 3Sheet1Drawing View1Drawing View2
A21 - Tail Rotor Hub AssemblySheet1Drawing View1Drawing
View3
A22 - Pitch Slider AssemblySheet1Drawing View1
A23 - Pitch Slider & Tail Rotor Hub InstallSheet1Drawing
View1Drawing View2
A24 - Tail Push Rod & GuidesSheet1Drawing View1Drawing
View2
A25 - Tail Boom InstallationSheet1Drawing View1
A26 - Boom Support AssemblySheet1Drawing View1Drawing View2
A27 - Main Gear & Pulley AssemblySheet1Drawing View1Drawing
View2Drawing View3Drawing View4
A28 - Drive Train InstallationSheet1Drawing View1
A29 - Drive Train Install Step #2Sheet1Drawing View1
A30 - Tail LinkageSheet1Drawing View1Drawing View2Drawing
View3Drawing View4
A31 - Swash Plate & Washout AssemblySheet1Drawing
View1Drawing View2Drawing View3Drawing View4Drawing View5Drawing
View6Drawing View7Drawing View8Drawing View9Drawing View10Drawing
View11
A32 - Head Block AssemblySheet1Drawing View1Drawing View2Drawing
View4Drawing View5Drawing View6Drawing View7Drawing View8Drawing
View9Drawing View10Drawing View20
A33 - Blade Grip & Rotor Head AssemSheet1Drawing
View1Drawing View2Drawing View3Drawing View4Drawing View5Drawing
View6
A34 - Rotorhead to Swashplate AssemblySheet1Drawing View1Drawing
View2Drawing View4
A35 - Rotorhead InstallationSheet1Drawing View1Drawing View2
A36 - Elevator LinkageSheet1Drawing View1Drawing View2
A37 - Aileron LinkageSheet1Drawing View1Drawing View2
A38 - Pitch Servo LinkageSheet1Drawing View1Drawing View2
A39 - Throttle LinkageSheet1Drawing View1Drawing View2
A40 - Canopy Blades and PaddlesSheet1Drawing View1Drawing
View3Drawing View4
A41 - Tail Blade InstallSheet1Drawing View1