Swingin' Leaves Earrings- a new wirework tutorial Good morning! Got another wirework tutorial for you- this one doesn't take much wire, and requires only minimal skills- it's pretty forgiving, thanks to the use of hammers. (Yeah, I really do have a thing for hammering!) These earrings are very kinetic- lots of movement, and any color of wire will do. Get your tools and wire ready- these are fast, fun, and easy! To make this project, you're going to need- Tools:Flush cutters or wire nippers Nylon jawed pliers Flat chain nose pliers Round nose pliers Needle files Bent nose pliers (optional, but they do mak e things easier) Needle nose pliers without teeth (optional) Anvil or bench block Ball peen hammer Wire:2- 5" lengths of 18 or 20 gauge wire (for large leaves) 2- 3 1/4" lengths 20 gaug e wire (for small leaves) 2- 1" lengths 20 gauge wire (for bead pins) 2- 1 3/4" or 2" lengths 20 gauge wire (for earwires- smaller for the simple wire, longer for beaded e arwires) Plus:2- 1/4"-3/8" beads 2- 4mm or smaller coordinating beads for earwires, if using
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Got another wirework tutorial for you- this one doesn't take much wire, and requires only minimal skills- it's
pretty forgiving, thanks to the use of hammers. (Yeah, I really do have a thing for hammering!) These earringsare very kinetic- lots of movement, and any color of wire will do.
Get your tools and wire ready- these are fast, fun, and easy!
To make this project, you're going to need-
Tools:
Flush cutters or wire nippers
Nylon jawed pliersFlat chain nose pliers
Round nose pliers
Needle filesBent nose pliers (optional, but they do make things easier)
Needle nose pliers without teeth (optional)
Anvil or bench block
Ball peen hammer
Wire:
2- 5" lengths of 18 or 20 gauge wire (for large leaves)
Ok, hammer 'em! I used a ball peen hammer's rounded end, because frankly, you can hide a lot of wireworking
sins with hammering. (I tend to gouge wires, make imperfect shapes, etc. It's OK. I can live with that. Because I
have hammers.) When hammering these, avoid the necks of your wraps, but do hammer the sides and bottom
V's. I also tapped the loops, using the little peg-thingy on my anvil, to help disguise the marks that I made withthe round nosed pliers (I grabbed the wires too tight!), and to strengthen them.
Now you have a pile of beaten, fallen leaves! Don't they look nicer?
Tidy them up with your nylon jaw pliers, so your pretty hammer marks don't get marred. You can also give
them a slight curve, if you wish- I bowed mine slightly, so that the facing sides rounded outwards just a bit. Thisis also a good time to straighten up your top loops, etc. With the nylon jaws, you can crimp them down nice and
neat, so the loops are flat to the rest of the leaf, with no worries!
Now you're going to attach them to each other. Here's a tip that will serve you well with any jewelry-making-
open the hanging loops on your large leaves just as you would a jump ring. When opening a jump ring, you
never pull it open- you push it open sideways, while holding it with two pairs of pliers, and close it the same
way. In this case, you won't need two sets of pliers, but you're going to twist the loops open, and then closed
again, after adding your little leaves. Like this:
Use a needle file to round out the hammered end, so that no one cuts themselves on it!
Now make either a simple loop, or a wrapped loop, to complete your bead dangles. Because these unakite
lovelies were only 1/4" long, I used the wrapped loop technique. Take your flat chain nose pliers, and cock thewire over sharply...
Swap over to your round nosed pliers, and start your loop....
Change your plier's position as often as needed- it's not a race.When the loop's complete, wrap the wire end around the neck of the loop a couple of times, and clip the excess.
Curl the wire around the barrel of the pencil, like so. Make sure that you have 3/8" longer on one side than theother. This is where your hanging loop will be.
Using your round nose pliers, roll that loop right up, so that the neck is right about at the same length as theother end.
Instead of the 1 3/4" wires, cut yourself some 2" pieces, and grab some 24 or 28 gauge wire, plus your little
beads. Instead of curling the wires first, make your loop, then slide the bead down, THEN curl the wires aroundthe pen. Shape the business end of the earwire with the pliers, just like last time, but after that, gently hammer
your wires with a flat hammer, avoiding the bead like the plague. Wrap the looped side of the wire tightly with
the smaller gauge wire, tuck in the ends, and viola! Beaded earwires!
Oh, and file 'em. Don't forget to file 'em!
Both versions look great, though- with the copper ones, I wanted the unakite beads to really pop- sadly, my
camera and lighting disagreed with me. (They're MUCH prettier in person!)
And the crackle-glass ones remind me of an off-color peacock's feathers. I used simple headpins on these beads,
and spiraled the wire from the wrapped loops around, to make faux bead caps, on the tops.
Hope you've enjoyed the tutorial- the originals pictured here will be available on Uniting a Family as one-time
offers, so if you're feelin' lazy but want a pair, and you want to help a good cause, pop over there and get 'em!
(You can read about our fund drive here. The backstory can be found here.)