Swimming Pool and Spa Water Chemical Adjustments · 184 The Chemistry and Treatment of Swimming Pool and Spa Water ... level (Taylor 2002). Based ... Calculation of Swimming Pool
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
182 The Chemistry and Treatment of Swimming Pool and Spa Water
Recommended Swimming Pooland Spa Water Parameters
The recommended ranges for swimming pooland spa water parameters are summarized inTable 1, where: FC equals the free chlorine, CCequals the combined chlorine, and TB equals thetotal bromine.
Swimming Pool and Spa WaterChemical Adjustments
John A. WojtowiczChemcon
This paper deals with adjustments to swim-ming pool and spa water chemical parameterssuch as pH, alkalinity, hardness, stabilizer, andchlorine. It discusses test kit acid and base de-mand tests and provides equations for calculatingrequired acid and base additions for adjusting pHbased on the test results. It also discusses a math-ematical approach for calculating acid and baseadditions (and associated alkalinity changes) andpH changes resulting from addition of sodiumbicarbonate (for alkalinity adjustment) and cya-nuric acid (for stabilizer adjustment) based onswimming pool chemical equilibria. Tables,graphs, and a general equation are provided fordetermining required acid and base additions for
Total Dissolved Solids (ppm) n/a n/a Initial TDS + 1500
John A. Wojtowicz – Chapter 8.1 183
Factors Affecting SwimmingPool and Spa Water Parameters
Carbon Dioxide Loss – Carbon dioxide iscontinually evolved from swimming pool waterbecause pools are normally supersaturated withcarbon dioxide. This causes an upward drift in thepH and necessitates periodic pH adjustment withacid (Wojtowicz 1995a). In spas, the upward driftis accelerated by the higher temperature and useof aeration.
Acidic Sanitizers – Acidic sanitizers suchas chloroisocyanurates can significantly retardthe rise in pH because of the large quantity of acidthat they produce (Wojtowicz 1995b). Gaseouschlorine can completely offset the upward pH risedue to CO2 loss and cause a downward drift.
Alkaline Sanitizers – Alkaline sanitizerssuch as hypochlorites contain low levels of alka-line and basic substances that will augment theupward pH drift, but only to a small extent(Wojtowicz 1995b).
Water Evaporation – Water used to re-place that lost by evaporation will increase alka-linity and hardness.
Filter Backwashing – Water used to re-place that removed via filter backwashing canaffect alkalinity and hardness depending on itscomposition.
Analysis of Swimming Pool andSpa Water via Test Kit
A summary of swimming pool and spa wateranalysis via test kit is presented in Table 2.
Table 2. Summary of Swimming Pool and Spa Water Parameter Measurement
Parameter MeasurementA
Free Chlorine (FC) Reaction with DPDB produces a pink color proportional to concentration, which is quantified by comparison with a standard color scale. Alternatively, drop-wise titration with standard FASC solution to extinction of the pink color can be used; the number of drops of FAS being proportional to the FC concentration.
Combined Chlorine (CC) Addition of potassium iodide catalyzes reaction of CC with DPD and allows its determination.
pH Treatment with phenol red indicator produces a color ranging from red (basic) to yellow (acidic). The pH is determined by comparison with a standard color scale.
Acid Demand The sample from pH measurement is titrated drop-wise with a standard dilute acid solution to the desired pH, the number of drops being proportional to the acid demand.
Base Demand Similar to acid demand except that a standard base solution is used.
Total Alkalinity Titration with standard acid solution in the presence of mixed bromocresol green-methyl red indicator.
Calcium Hardness A buffered sample is titrated with EDTAD in the presence of an indicator, eg, Eriochrome Black T.
Cyanuric Acid (CA) Treatment of a sample with melamine solution produces turbidity (ie, a precipitate of melamine cyanurate) that is proportional to the CA concentration.
A) Carried-out using test kits, eg, Taylor. B) N,N-Diethyl-p-phenylenediamine. C) Ferrous ammonium sulfate. D) Ethylenediamine tetra-acetic acid.
184 The Chemistry and Treatment of Swimming Pool and Spa Water
Swimming Pool and Spa WaterpH Adjustment via Test Kit
Analysis
Acid Demand – This test determines theamount of acid required to reduce the pH ofswimming pool or spa water when it has exceededthe recommended range of 7.2 to 7.8 (see Table 1).The acid demand test involves titration of a poolor spa water sample with acid to a desired pH;e.g., using a Taylor test kit. A standard acidsolution (dilute sulfuric acid) is added dropwise toa known volume (44 mL) of pool or spa watercontaining a pH indicator (phenol red) until thedesired pH is obtained as determined by the colorchange of the indicator. Tables are available toconvert the number of drops of acid solution tovolume of pool acid (muriatic acid, i.e., hydrochlo-ric acid, HCl) to decrease the pH to the desiredlevel (Taylor 2002). Based on these Tables, thequantity of muriatic acid (31.45% HCl) requiredcan also be calculated using the following for-mula:
VMA (fl. oz ) = 9.165•10–4•N•V
where: VMA (fl. oz ) equals the volume of muriaticacid, N equals the number of drops of acid de-mand reagent, and V equals the pool or spavolume (gals).
Dry acid, i.e., sodium bisulfate, can also beused to lower pH. Tables are available for deter-mining the quantity of bisulfate to add based onthe number of drops of reagent and pool or spavolume. The quantity of sodium bisulfate also canbe calculated using the following formula, whichis based on these Tables:
WBS (oz) = 1.148•10–3•N•V/p
where: WBS equals the weight of sodium bisulfate,N equals the number of drops of test kit aciddemand reagent, V equals the volume of pool orspa, and p equals the degree of purity of sodiumbisulfate.
Base Demand – This test determines theamount of sodium carbonate (soda ash) requiredto increase the pH of pool or spa water when thepH has dropped below the recommended range of
7.2 to 7.8, e.g., due to a high dose of gaseouschlorine or high usage of chloroisocyanurates.The base demand test involves titration of a poolor spa water sample with base to a desired pH;e.g., using a Taylor test kit. A standard basesolution (dilute sodium hydroxide) is addeddropwise to a known volume (44 mL) of pool or spawater containing a pH indicator (phenol red)until the desired pH is obtained as determined bythe color change of the indicator. Tables areavailable to convert the number of drops of basesolution to weight of soda ash (sodium carbonate)to increase the pH to the desired level (Taylor2002). The quantity of 100% sodium carbonaterequired can also be calculated using the follow-ing formula:
WSC (oz) = 5.12•10–4•N•V
where: WSC equals the weight of sodium carbon-ate, N equals the number of drops of base demandreagent, and V equals the volume of pool or spawater (gals).
Calculation of Swimming Pooland Spa Water Chemical
Parameters and Adjustments
Computer Assisted CalculationsThe basic data and equations for calculating
certain changes in water chemistry have beenpublished in previous issues of the journal (e.g.,see Wojtowicz 1995b, 1995c, 2001, and 2002). Thechanges include: acid and base requirements foradjusting pH and pH changes on addition ofchlorine, sodium bicarbonate, and cyanuric acid.The input data for the calculations are: pool or spavolume, water temperature, total dissolved sol-ids, initial and final pH, total alkalinity, cyanuricacid, boron, and av. Cl. In the case of carbondioxide loss calculations, additional data are nec-essary such as pool or spa surface to volume ratio,pumping rate, and pump duty cycle.
Variables, Constants, and ConversionFactors
Various conversion factors and variable sym-
John A. Wojtowicz – Chapter 8.1 185
bols are used in the following discussions and aresummarized in Table 3.
pH Adjustment
Decreasing pH with Muriatic Acid –Addition of muriatic acid lowers the pH of swim-ming pool water because it is highly ionized,thereby increasing the concentration of hydrogenions (H+) which suppresses ionization of the re-spective acidic species resulting in decreasedconcentrations of the alkaline ions: carbonate,bicarbonate, cyanurate, and borate, i.e., the equi-libria below are shifted to the right.
CO32– + H+ HCO3
–
HCO3– + H+ H2CO3 H2O + CO2
H2Cy– + H+ H3Cy
B(OH)4– + H+ H3BO3 + H2O
The required quantity of acid is readily cal-culable from the decrease in calculated total alka-linity at the new pH. Each mol of added acidneutralizes one mol of total alkalinity.
Tables 3A to 6A contain calculated values ofmuriatic acid required to reduce pHs in the 7.8 to8.2 range to 7.2 at different total alkalinities (80to 210 ppm) and cyanuric acid levels (50 to 200
Table 3. Summary of Variables, Constants, and Conversion Factors Variables Conversion Factors
V = pool or spa volume (gal) 28.35 g/oz TA = total alkalinity (ppm) 29.57 mL/fl. oz
d = density (g/mL) 1000 mg/g p = degree of purity (% assay/100) 436.5 g/lb
Constants 3.7854 L/gal Equivalent wt. of CaCO3 (50)
ppm). The data are also shown graphically inFigures 1 to 4. The graphs show that the quantityof acid varies linearly with total alkalinity at agiven starting pH. The conditions used for thecalculations are: 80°F, 1000 ppm TDS, 3 ppm av.Cl, and 10,000 gals pool volume.
Multiple linear regression analysis of all ofthe data in Tables 3A to 6A was performed usingthe following equation form involving one depen-dent variable (VMA) and three independent vari-ables (pH, TA, and CA):
VMA = a + b(pH) + c(TA) + d(CA)
where: VMA equals the volume of 31.45% muriaticacid (fl oz), TA equals the total alkalinity (ppm),and CA equals the cyanuric acid (ppm). Theregression analysis showed an excellent correla-tion coefficient (0.997) and a very low standarddeviation (0.02), resulting in the following equa-tion:
This equation estimates the values in Tables 3Ato 6A to within ± 2% on average.
Borate will affect the calculated quantity ofacid. For example, the presence of 100 ppm ofboric acid (17.5 ppm boron) will increase thecalculated quantity of muriatic acid (required toreduce pH from 8.2 to 7.2) from 62.1 fl. oz to 78.2fl. oz at 100 ppm CA and 170 ppm total alkalinity.
186 The Chemistry and Treatment of Swimming Pool and Spa Water
Table 3A. Volume (fl. oz) of 31.45% Muriatic Acid Total Alk.
Tables 3B to 6B contain calcu-lated values of muriatic acid requiredto reduce pHs in the 7.3 to 7.7 rangeto 7.2 at different total alkalinities(80 to 210 ppm) and cyanuric acidlevels (50 to 200 ppm). These Tablesare useful for determining the quan-tity of muriatic acid required to re-duce pH from the 7.8 to 8.2 range tointermediate values in the 7.3 to7.7range. For example, to calculate thequantity of muriatic acid required toreduce pH from 8.2 to7.5, one wouldsubtract the quantity of acid to re-duce pH from 7.5 to 7.2 from thatrequired to reduce pH from 8.2 to7.2.
Decreasing pH with Sulfu-ric Acid – The above equation alsoworks equally well for 38.5% sulfu-ric acid (d = 1.29 g/mL).
Decreasing pH with SodiumBisulfate – It will require 1.32 oz of95% sodium bisulfate to provide thesame pH reduction as one fl. oz of31.45% muriatic acid. Bisulfate (i.e.,bisulfate ion) lowers pH by reactingwith hydroxyl ion and is convertedto sulfate ion.
HSO4– + OH– → SO4
2– + H2O
Decreasing pH with CarbonDioxide – By contrast with mineralacids (hydrochloric and sulfuric) andbisulfate, carbon dioxide decreasespH (without affecting alkalinity) byincreasing the concentration of car-bonic acid.
Increasing pH with SodiumCarbonate – As discussed earlier,swimming pool and spa pH tends todrift upward. Thus, acid addition istypically necessary to adjust the pHto the recommended range. By con-trast, pools treated with chlorinewill offset the upward pH drift dueto CO2 loss because of the acidityintroduced, which lowers pH anddecreases alkalinity. This will ne-cessitate addition of soda ash, which
increases both pH and alkalinity. Dissolution ofsodium carbonate in water produces hydroxyland bicarbonate ions:
CO32– + H2O HCO3
– + OH–
The hydroxyl ions decrease the concentra-tion of hydrogen ions via the equilibrium:H2O H+ + OH–. This raises the pH, causingincreased ionization of carbonic, cyanuric, andboric acids producing bicarbonate, cyanurate, andborate ions, i.e., the reverse of the reactions when
acid is added as shown in the previous section.The quantity of sodium carbonate required
is calculable based on the increase in alkalinity atthe higher pH. Tables 7–10 contain calculatedvalues of sodium carbonate required to raise pHto 7.8 from initial pHs of 7.2–7.7. The conditionsfor the calculations were: 80°F, 3 ppm av. Cl, 1000ppm TDS, total alkalinity of 70–210, and CA of50–200 ppm. Plots of the data are shown inFigures 5–8. They show that the required quan-tity of sodium carbonate varies linearly with totalalkalinity at a given pH and CA concentration.
Multiple linear regression analysis of all the
192 The Chemistry and Treatment of Swimming Pool and Spa Water
data in Tables 7–10 did not yield a satisfactorypredictive equation as in the case of acid addition,because the data was not linear with respect topH. Therefore, the data from each Table wasregressed separately using the following equa-tion form consisting of the dependent variableWSC (oz sodium carbonate) and the independentvariable pH:
where: A1, B1, and C1 are regression constantsand A2, B2, and C2 are constants for extrapolatingtotal alkalinity, and F equals (TAa – TAo)/10where TAa is the actual total alkalinity, and TAois the lowest total alkalinity for a given CA leveland is equal to 70, 90, 110, and 130 for the data inTables 7–10, respectively. The constants are sum-marized in Table 11. These equations estimatethe values in Tables 7–10 to within ±2% on aver-age.
Because of chlorine’s propensity for lower-ing pH, pool service companies using chlorine forsanitization maintain pH at or above 7.8. Poolsare treated once a week, and typically, the av. Claverages about 3 ppm before chlorination. Thewater is treated with about 8 oz chlorine/10,000gal, which is equivalent to 6 ppm av. Cl. Totalalkalinity and stabilizer are maintained at about100 ppm. The total alkalinity will be reduced by4.23 ppm. If the pH is at 8.0 when the chlorine isadded, it will decrease to 7.54. Raising the pH to7.8 will require 13.4 oz of soda ash and will raisethe total alkalinity by 9.4 ppm. When all of theadded av. Cl has decomposed to HCl, the totalalkalinity will be reduced by an additional 4.23ppm. Thus, the net change in total alkalinity willbe about +0.9 ppm.
If the quantity of soda ash is just sufficient toneutralize all of the acidity due to chlorine, there
should be no net change in alkalinity as shownbelow and will require 1.5 lb of soda ash per poundof chlorine or 12.0 oz in the above example.
Cl2 + H2O → HOCl + HCl
HOCl → HCl + 0.5O2
Na2CO3 + 2HCl → 2NaCl + CO2 + H2O
Overall: Na2CO3 + Cl2 → 2NaCl + CO2 + 0.5O2
However, pool alkalinity can still changedue to the effects of filter backwashing and makeupwater.
Increasing pH with Sodium Hydroxide– Addition of sodium hydroxide (caustic soda) towater raises pH by increasing the concentrationhydroxyl ions. In the above example, it wouldrequire 21.7 fl. oz of 30% sodium hydroxide toincrease the pH to 7.8. This would raise the totalalkalinity from 95.8 to 104.2 ppm. Decompositionof all of the added chlorine would reduce the totalalkalinity back to its original value of 100 ppm,thus no change in alkalinity would occur and is inagreement with the following reaction stoichiom-etry obtained on substitution of sodium hydrox-ide in place of soda ash in the above reactionsequence:
2NaOH + Cl2 → 2NaCl + H2O + 0.5O2
Alkalinity Changes after pHAdjustments
Decrease in Alkalinity after MineralAcid Addition – Mineral acid (i.e., hydrochloricor sulfuric) addition for pH adjustment lowersalkalinity by reacting with bicarbonate, carbon-ate, cyanurate, and borate (if present) ions as
Table 11. Summary of Constants for Calculating Soda Ash Addition CA A1 A2 B1 B2 C1 C2 50 2732.097 302.340 -683.781 -76.358 42.768 4.821
196 The Chemistry and Treatment of Swimming Pool and Spa Water
discussed earlier. The decrease in total alkalinity(∆TA) is calculable from the quantity of acidadded.
∆TA = (fl. oz acid)•29.57•d•p•1000•50/(EW•V•3.7854)
where: d equals 1.16 for muriatic acid and 1.29 forsulfuric acid, p equals 0.3145 for muriatic acidand 0.385 for sulfuric acid, EW is equivalentweight – 36.46 for hydrochloric acid and 49.04 forsulfuric acid. The above calculation yields similarresults (to within 1%) for each acid. Thus, onequart (i.e., 32 fl oz) of 31.45% muriatic acid and38.5% sulfuric acid added to 10,000 gal of poolwater reduces alkalinity by 12.5 and 12.7 ppm,respectively, as calculated by the following con-densed formulas:
∆TA = 3912.0•VMA/V
∆TA = 3962.8•VSA/V
where: VMA equals the volume (fl oz) of muriaticacid and VSA equals the volume (fl oz) of sulfuricacid.
Decrease in Alkalinity after SodiumBisulfate Addition – The change in total alka-linity when sodium bisulfate is used for pH ad-justment is calculated as follows:
where: WBS equals the weight (oz) of sodiumbisulfate, 120 is the molecular weight of sodiumbisulfate. Assuming a degree of purity of 0.95 (i.e.,95% purity), each pound (i.e., 16 oz) of sodiumbisulfate added to 10,000 gal of pool water willreduce total alkalinity by 4.7 ppm.
Increase In Alkalinity after Sodium Car-bonate Addition – The increase in total alkalin-ity (∆TA) resulting from addition of sodium car-bonate (soda ash) can be calculated using thefollowing formula:
where: WSC equals the weight (oz) of sodiumcarbonate, and 53 equals the equivalent weight ofsodium carbonate. Assuming a typical degree ofpurity of 0.998 (i.e., 99.8% purity), each pound(i.e., 16 oz) of soda ash added to 10,000 gals of poolwater will increase the total alkalinity by 11.3ppm.
Alkalinity Adjustment
All tap and well water contain varyingamounts of alkalinity depending on the source. Innew pools the alkalinity may require adjustmentto the recommended range (see Table 1). In estab-lished pools, makeup water to replace evapora-tion losses will increase the pool or spa alkalinity.In addition, alkaline sanitizers will increase al-kalinity to a small extent, whereas acidic sani-tizers will decrease alkalinity to a significantextent (Wojtowicz 1995b). High alkalinity is low-ered by acid addition whereas low alkalinity isincreased with sodium bicarbonate.
Increasing Alkalinity with Sodium Bi-carbonate – Sodium bicarbonate is used to in-crease total alkalinity. Addition of sodium bicar-bonate to pool water will increase the concentra-tion of bicarbonate ions, which will repress ion-ization of carbonic acid resulting in a lower hydro-gen ion concentration and a higher pH.
H2CO3 HCO3– + H+
However, the effect is very small. For example,increasing the total alkalinity by 20 ppm withsodium bicarbonate in pool water at 80°F, pH 7.5,total alkalinity 80 ppm, cyanuric acid 100 ppm,av. Cl 3 ppm, and TDS 1000 ppm will increase thepH to only 7.55.
The quantity of sodium bicarbonate (WSB(lb)) can be calculated using the following equa-tion:
where: ∆TA equals the increase in total alkalinity(ppm), 84 equals the molecular weight of sodiumbicarbonate, and p is typically 1.0, i.e., 100%assay. Tables are available showing dosages forvarious water volumes.
John A. Wojtowicz – Chapter 8.1 197
Decreasing Alkalinity with Mineral Acid– The quantity of mineral acid necessary to re-duce total alkalinity (TA) by a specified amountcan be calculated using the following equationsobtained by rearrangement of equations usedearlier.
VMA = 2.556•10–4•(∆TA) •V
VSA = 2.523•10–4•(∆TA) •V
where: VMA equals the volume (fl oz) of 31.45%muriatic acid, VSA equals the volume (fl oz) ofsulfuric acid. Reduction of total alkalinity by 10ppm requires 1.6 pints of muriatic acid.
Decreasing Alkalinity with SodiumBisulfate – Similarly, the earlier equation can berearranged to give the quantity of bisulfate (WBSoz) necessary to reduce total alkalinity by a speci-fied amount.
WBS = 3.205•10–4•(∆TA) •V/p
Hardness Adjustment
Increasing Hardness – All source watercontains some calcium hardness. If necessary,the calcium hardness (CH) can be adjusted to therecommended range by the addition of calciumchloride (typically the dihydrate CaCl2•2H2O).The required dosage is readily calculable usingthe following equation:
where: WCC equals lbs of calcium chloride dihy-drate, DCH equals the increase in calcium hard-ness (ppm), 147 equals the molecular weight ofcalcium chloride dihydrate, 100 equals the mo-lecular weight of calcium carbonate, and p equalsthe degree of purity of calcium chloride dihydrate(typically 0.98). Raising calcium hardness (ex-pressed as ppm calcium carbonate) by 10 ppmrequires 1.25 lb of 98% calcium chloride dihy-drate per 10,000 gals of pool water. Tables areavailable showing dosages for various water vol-umes.
Decreasing Hardness – Alkaline sanitizerssuch as calcium hypochlorite add small amountsof calcium hardness to the water (Wojtowicz1995b). Makeup water to replace evaporationlosses also adds calcium hardness to pool or spawater. Makeup water used to replace water re-moved by backwashing can reduce calcium hard-ness if its hardness is lower. Thus, frequentbackwashing can keep hardness in the recom-mended range.
Stabilizer Adjustment
Increasing Stabilizer Concentration –The stabilizer concentration is adjusted by addi-tion of cyanuric acid (CA). In a new pool, thestabilizer concentration can be adjusted to 50ppm by addition of 4.2 lb of cyanuric acid (99%assay) per 10,000 gal of water. The CA dose forother concentrations and water volumes can becalculated using the following equation:
CA (lb) = ∆CA•V•3.7854/(1000•453.6•p) = 8.345•10–6•∆CA•V/p
where: ∆CA equals the ppm increase in the CAconcentration.
Decrease in pH after Cyanuric Acid Ad-dition – Addition of cyanuric acid to swimmingpool or spa water will increase the hydrogen ionconcentration as the result of ionization, there-fore, lowering the pH.
H3Cy H2Cy– + H+
The effect is significant. For example, increasingthe cyanuric acid concentration to 50 ppm in poolwater at 80°F, pH 7.5, total alkalinity 100 ppm,initial cyanuric acid 0 ppm, av. Cl 3 ppm, andTDS 1000 ppm will lower pH to 6.99. At thispoint, there are two options:1. Let the pH drift and under normal conditions
it will eventually increase to 7.5 and evenhigher due to loss of carbon dioxide. For a20,000–gal pool with an average depth of 5feet, a pumping rate of 42 gal/min, a 24–hourpump duty cycle, the pH will reach 7.50 afteronly about 2.4 days.
198 The Chemistry and Treatment of Swimming Pool and Spa Water
2. Add base to immediately increase the pH tothe original value of 7.5.
In the first case there will be no change inalkalinity, whereas in the second, there will beand will depend on the base added. With soda ash,it will require 86.8 oz to increase the pH back to7.5. This will increase the total alkalinity to 130.7ppm. Instead of soda ash, sodium hydroxide (i.e.,caustic soda) can be added and will result in amuch lower increase in total alkalinity. It willrequire 86.8 fl. oz of 30% sodium hydroxide andwill increase the total alkalinity to 116.8 ppm,about half that of soda ash.
Decreasing Cyanuric Acid Concentra-tion – In hypochlorite or chlorine sanitized poolsor spas, the cyanuric acid concentration decreaseswith time due to backwashing, splash out, anddecomposition requiring periodic adjustment. Bycontrast, in water sanitized with chloro-isocya-nurates the CA concentration normally increaseswith time. Excessive CA concentrations can bereduced and controlled by adjusting thebackwashing frequency and duration (Wojtowicz2002).
Summary of Ancillary ChemicalDosages
A summary of ancillary chemical dosagesused for adjusting pH, alkalinity, hardness, andstabilizer is shown in Table 12.
Chlorine Sanitizer Adjustment
The required dosage of solid sanitizers (WSANincluding gaseous chlorine) can be calculatedusing the following formula:
where: ∆FC equals the increase in free chlorine,p equals the degree of purity of sanitizer (i.e., %av. Cl/100). The required dosage of liquid chlorinesanitizers such as sodium hypochlorite can becalculated using the following formula:
where: WSH equals the volume of sodium hy-pochlorite. Calculated dosages for various chlo-rine sanitizers are summarized in Table 13.
References
ANSI/NSPI–4 1999 Standard for Aboveground/Onground Residential Swimming Pools
ANSI/NSPI–5 1995 Standard for ResidentialInground Swimming Pools
ANSI/NSPI–5 2003 Standard for ResidentialInground Swimming Pools
Taylor Technologies, Inc., “Pool & Spa WaterChemistry”, Sparks, MD, 2002.
Wojtowicz, J.A. 1995a “Swimming Pool WaterBalance – Part 2: Factors Affecting theCalcium Carbonate Saturation Index”,Journal of the Swimming Pool and SpaIndustry 1(2)1995:9–15.
Wojtowicz, J.A. 1995b “Swimming Pool WaterBalance – Part 3: Factors Affecting Loss ofCarbon Dioxide”, Journal of the SwimmingPool and Spa Industry 1(3)1995:19–26.
Wojtowicz, J.A. 1995c “Swimming Pool WaterBalance – Part 1: The Effect of Cyanuric Acidand other Interferences on CarbonateAlkalinity Measurement”, Journal of theSwimming Pool and Spa Industry 1(1)1995:7–13.
Wojtowicz, J.A. “Swimming Pool Water Balance –Part 4: Calcium Carbonate PrecipitationPotential”, Journal of the Swimming Pool andSpa Industry 2(2)1996:23–29.
Wojtowicz, J.A., “The Carbonate System inSwimming Pool Water”, Journal of theSwimming Pool and Spa Industry4(1)2001:54–59.
Wojtowicz, J.A., “Factors Affecting the CyanuricAcid Concentration in Swimming Pools”,Journal of the Swimming Pool and SpaIndustry 4(2)2002:17–22.
200 The Chemistry and Treatment of Swimming Pool and Spa Water