svsembedded@gmail.com,myhobby projectss@gma il.com CONTACT: 9491535690 AVR ISP Flash Programmer-(STK200/30 0): INTRODUCTION: This ISP Programmer can be used either for In-System Programming or as a stand-alone SPI programmer for Atmel ISP programmable devices. The programming interface is compatible to STK200+/300 ISP programmer hardware so the users of STK200 can also use the software which can program both the 8051 and AVR series devices. This STK - 200 AVR Programmer is compatible wi th PonyProg , Code Vi sionAVR (CV AVR), AVRDude, AVRISP etc programming software. It does not require any external power supply; it takes power from yourtarget board. The dongle a ttaches to your PC via a standard DB25 Parallel port. FEATURES : • Connects to PC via Parallel port (LPT-1) • No need for external power supply as it takes the power supply from target board. • Very compact, easy to use. • One year Manufacturer Warranty. • Full support for How to connect / use software SUPPORTED DEVICES: AT89S51, AT89S52, ATtiny12, ATtiny13, ATtiny15, ATtiny26, ATmega8, ATmega88, ATmega323, ATmega128, ATmega16, ATmega168, ATmega8L, ATmega16L, ATmega64, ATmega32, ATmega64L, ATmega32L, svsembedded@gmail.com,myhobby projectss@gma il.com CONTACT: 9491535690
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
This ISP Programmer can be used either for In-System Programming or as a stand-alone
SPI programmer for Atmel ISP programmable devices. The programming interface is compatible
to STK200+/300 ISP programmer hardware so the users of STK200 can also use the software
which can program both the 8051 and AVR series devices. This STK - 200 AVR Programmer is
compatible with PonyProg, CodeVisionAVR (CV AVR), AVRDude, AVRISP etc
programming software. It does not require any external power supply; it takes power from your target board. The dongle attaches to your PC via a standard DB25 Parallel port.
FEATURES :
• Connects to PC via Parallel port (LPT-1)• No need for external power supply as it takes the power supply from target board.
PRODUCT DESCRIPTION:This product is a Class 2 SMT Bluetooth Module used CSR BC4 Chipset .It provides data
communications. It interfaces with a host through USB or UART
GENERAL FEATURES:
• CSR BlueCore4, single chip Bluetooth system• Class 2 Bluetooth version 2.0 +EDR •
Range in excess of 10 meters• Temperature range -40ºC to +85 ºC• Data transfer rate up to 300 kbps• On board voltage regulator • 3.3v Dou UART and USB• Simple AT style command set control• Multipoint support• Fully approved end product• Field upgradeable
• Supports co-located Wi-Fi• Adaptive frequency hopping• SPI interface• Size 25x14.5x2.2mm• Lead free -RoHS compliant
• Factory configurable to 3.3v supply• Support for 8Mbit Memory
BENEFITS:
• fastest time to market• support for encryption and authentication• low power • excellent immunity to interference from adaptive frequency hopping• ideal for embedded systems• lowest cost of ownership
GSM (Global System for Mobile Communications) is world’s most famous Mobile platform.Mobile phones with SIM cards use GSM technology to help you communicate with your family,
friends and business associates.
GSM systems have following advantages over basic land line telephony systems:
1. Mobility.
2. Easy availability.
3. High uptime.
TECHNICAL SPECIFICATIONS:
•
RS -232 INTERFACE/ TTL PINS EXTRACTED ON BOARD.• ON BOARD AC/DC WITH 5VDC- EXTRACTED PIN OUT.
• RINGER – FOR INCOMMING CALL.
• SMS/ GPRS WITH TCP-IP STACK ON MODULE.
• ON BOARD ANTENNA/ SMA CONNECTOR WITH 3 db ANTENNA.
• MODULAR 2 PCB CONSTRUCTIONS FOR EASE OF IMPLEMENTATION.
• EASY AT COMMANDS FOR INTERFERENCE.
TARANG MODULES (ZIGBEECOMPLIANT PLATFORM)
INTRODUCTION:Ready to use Low Power modules. These are the modules that power our tags, root and
routers. Standalone network using TarangMesh. For smaller campuses OR for situations where
Ethernet backbone is not present. Tarang modules will be running TarangMesh software.Tarang
router nodes at all vantage points / “cells”. The assets shall be tagged by Tarang based tags. This
would be a mobile node. The tags will emit a message every configured amount of time (ex. 1
min).The router which picked up the signal serves to identify the location of the tag. If multiple
routers pick the signal up, RSSI based distinction can be made. By use of TarangMesh +
Ethernet backbone For situations where the asset tracking network can span multiple locations
connected over Ethernet
FEATURES :
• Uses FreescaleMC13213 chipset• ZigBeeCompliant Platform• Serial Interface ( UART )• Direct sequence spread spectrum technology• Each direct sequence channel has 64K unique network addresses• Configurable Transmit Power: Up to 0 dBm, 18 dBmand 30 dBm• RF data rate: 250 kbps• Power saving modes
A resistive touch screen is constructed with two transparent layers coated with a
conductive material stacked on top of each other. This is 4-wire resistive touch screen. When
pressure is applied by a finger or a stylus on the screen, the top layer makes contact with the
lower layer. When a voltage is applied across one of the layers, a voltage divider is created. The
coordinates of a touch can be found by applying a voltage across one layer in the Y direction and
reading the voltage created by the voltage divider to find the Y coordinate, and then applying a
voltage across the other layer in the X direction and reading the voltage created by the voltage
divider to find the X coordinate.
Once a touch is detected, the controller reads the x and y coordinates of the touch. Toread the coordinates, the pins are configured as previously described to drive the X lines and setthe Y sense pin as analog ADC inputs. Four ADC conversions are taken and averaged together toobtain the x coordinate reading. The same process is repeated to obtain the y coordinate.
FEATURES :
• Operating Voltage: 3.3 to 5.0 volts ±5%• Standby Sleep Current: <1uA• Operating “No touch” Current: 3.0mA typ.• Operating “Touch” Current: 17mA typ with a touch sensor having 200Ω layers.• Actual current is dependent on the touch sensor used
The 4-wire resistive touch is suitable for any application that requires fast and reliable
integration of touch in the design, including but not limited to:
• Personal Digital Assistants (PDA)
• Touch Screen Monitors
• Media Players
128X64 GRAPHIC LCD DISPLAY
INTRODUCTION:
JHD-12864A is a dot matrix graphic LCD module which is fabricated by low power COMS technology. It can display 128*64 dots size LCD panel using a 128*64 bit-mappedDisplay Data RAM (DDRAM). It interfaces with an 8-bit microprocessor.
FEATURES :
• Display format: 128*64 dots matrix graphic• STN yellow-green mode• Easy interface with 8-bit MPU• Low power consumption• LED back-light• Viewing angle: 6 O’clock • Driving method : 1/64 duty , 1/6.7 bias• + 5V power supply.
If you intend to use the touch panel you should first consider these 2 items:
• 128x64 GLCD with Soldered Connector • TOUCHPANEL OVERLAY For 128x64 GLCD
Very High Quality 128x64 yellow-black Graphical LCD Display with factory-mounted4-Wire Touchscreen.Only 5V is required to power this KS0108 compatible LCD. Negative
voltage supply (Vee) for the LCD screen drive and contrast is built into LCD module.
You can create your own touchpanel control code using any compiler and microcontroller
that has at least 4 ADC inputs, as shown in the Photos above.
Compatible 4 x 1mm pitch FPC connectors are inexpensive and available from all the