Simple stomp rocket Launcher Assemble the parts below. Joints can be glued or simply press fit. Do not glue the elbow fitting as it should rotate to adjust the launch angle. The ½ inch PVC pipe will slip inside the neck of a soda bottle – tape for a better seal if desired or bore a closely fitting hole through the bottle cap, slip the tubing through the cap and screw the cap down to seal. If using ¾ inch pipe, agrey conduit coupler is more flexible than white PVC and will allow the soda bottle’s neck to be jammed/screwed in securely to attach it. Rockets are made by loosely wrapping a half sheet (4 ¼ x 11) of card stock or construction paper around the removable launch tube and taping the seam lengthwise. Fins are added or cut into the bottom of the tube. Pinch the top shut and tape securely. Slide rocket over tube and stomp away! Materials 1 - 8’ stick of ½ ” PVC pipe (uses 5 ½’) 1 - ½ ” PVC cross fitting 2 - ½ ” PVC end cap 1 - ½ ” PVC elbow 2 liter soda bottle Card stock (65 or 110lb) Tape (to seal bottle neck if desired) PVC glue (if desired) soda bottle 12-18” pipe cross fitting 6” pipe elbow 12-18” pipe Launch tube can be removed for storage and to wrap rockets. Side view soda bottle 12-18” pipe cross fitting 6” pipe elbow & launch tube 12” pipe Top view 12” pipe cap cap Launcher can be made from ½ or ¾ inch PVC tubing. Size rockets to fit the tubing used. A Product of Yogi’s Workshop Idiosyncratic Carpentry & Shade Tree Engineering
13
Embed
Stomp Rocket - Launcherpapermodelingman.com/jj_sr1007/Stomp Rocket - Basic and Launcher.pdf · Simple stomp rocket Launcher Assemble the parts below. Joints can be glued or simply
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Simple stomp rocket LauncherAssemble the parts below. Joints can be glued orsimply press fit. Do not glue the elbow fitting as it should rotate to adjust the launch angle.The ½ inch PVC pipe will slip inside the neck of a soda bottle – tape for a better seal if desired or bore a closely fitting hole through the bottle cap, slip the tubing through the cap and screw the cap down to seal.If using ¾ inch pipe, agrey conduit coupler is moreflexible than white PVC and will allow the soda bottle’sneck to be jammed/screwed in securely to attach it.
Rockets are made by loosely wrapping a half sheet (4 ¼ x 11) of card stock or construction paper aroundthe removable launch tube and taping the seamlengthwise. Fins are added or cut into the bottomof the tube. Pinch the top shut and tape securely.
Slide rocket over tube and stomp away!
Materials1 - 8’ stick of ½ ” PVC pipe (uses 5 ½’)1 - ½ ” PVC cross fitting2 - ½ ” PVC end cap1 - ½ ” PVC elbow
2 liter soda bottleCard stock (65 or 110lb)Tape (to seal bottle neck if desired) PVC glue (if desired)
sodabottle
12-18”pipe
crossfitting
6”pipe
elbow
12-18”pipe
Launch tube canbe removed forstorage and to wrap rockets.
Side view
sodabottle
12-18”pipe
crossfitting
6”pipe
elbow &launch tube
12”pipe
Top view
12”pipe
cap
cap
Launcher can be madefrom ½ or ¾ inch PVCtubing. Size rockets tofit the tubing used.
A Product of Yogi’s WorkshopIdiosyncratic Carpentry &Shade Tree Engineering
½ inch PVC pipe stomp rockets
After forming the tube:Cut solid red lines to free fins, thenfold out on dotted line.
Glue over crimped top if desired
Roll and secure into a cone.
Roll into a cylinder and secure coneto the top. Assembly will slip over thetop of the rocket for a nose cone.
Roll and secure into a cone.
Roll into a cylinder and secure coneto the top. Assembly will slip over thetop of the rocket for a nose cone.
UNITED
STATES
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rocketsCrimp shut and tape or glue
After forming the tube:Cut solid red lines to free fins, thenfold out on dotted line.
Glue over crimpedtop if desired
Decorate with your owndesign using colored pensor markers.
Roll and secure into a cone.
Roll into a cylinder and secure coneto the top. Assembly will slip over thetop of the rocket for a nose cone.
Roll and secure into a cone.
Roll into a cylinder and secure coneto the top. Assembly will slip over thetop of the rocket for a nose cone.
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rockets
After forming the tube:Cut solid red lines to free fins, then fold out on dotted line.
Roll into a cylinder.
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rockets
After forming the tube:Cut solid red lines to free fins, then fold out on dotted line.
Roll into a cylinder.
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rockets
After forming the tube:Cut solid red lines to free fins, then fold out on dotted line.
Roll into a cylinder.
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rockets-Easy to Cut Fins
After forming the tube:Cut solid red lines to free fins, then fold out on dotted line.
Roll into a cylinder.
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
½ inch PVC pipe stomp rockets-Easy to Cut Fins
After forming the tube:Cut solid red lines to free fins, then fold out on dotted line.
Roll into a cylinder.
Crimp shut and tape or glue
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Crimp shut and tape or glueR
OLL IN
TO A C
YLIND
ER AN
D G
LUE TH
IS OVER
LAP
¾ inch PVC pipe stomp rockets
UNITED
STATES
Crimp shut and tape or glue
After forming the tube:Cut solid red lines to free fins, thenfold out on dotted line.
Glue over crimped topif desired
Roll and secureinto a cone.
Rol
l int
o a
cylin
der a
nd s
ecur
e co
neto
the
top.
Ass
embl
y w
ill s
lip o
ver t
heto
p of
the
rock
et fo
r a n
ose
cone
.
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
¾ inch PVC pipe stomp rocketsCrimp shut and tape or glue
After forming the tube:Cut solid red lines to free fins, thenfold out on dotted line.
Glue over crimped topif desired
Roll and secureinto a cone.
Rol
l int
o a
cylin
der a
nd s
ecur
e co
neto
the
top.
Ass
embl
y w
ill s
lip o
ver t
heto
p of
the
rock
et fo
r a n
ose
cone
.
RO
LL INTO
A CYLIN
DER
AND
GLU
E THIS O
VERLAP
Basic ¾” caliber stomp rocket.Half sheet (either way) of letter sized paper or card stock.Roll loosely around ¾” launch tube and tape seam.With rocket on the launch tube, crimp the top shut at the
dotted line and tape securely. You can glue on a reinforcing disk or nose cone if desired – not required.
Cut out and fold fins at bottom after assembling the rockettube – cut on the solid black and fold on the red dotted lines.Or, cut separate fins and tape/glue in place.
Place on ¾” launch tube and stomp away.
Start rolling here
Add graphics to this section
Overlap to this line – should be loose fit to slide easilyon launch tube