Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone:
0800 085 1678 (UK only)E-mail: [email protected] Web:
www.sti-europe.com
Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone:
0800 085 1678 (UK only)E-mail: [email protected] Web:
www.sti-europe.com
ADHESIVE BACK PCB SUPPORT(4) PROVIDED
PEEL BACKING
TO 8 CHANNEL RECEIVERSTI-34108
FEMALE JACK
MALE PLUG
24 4-CONDUCTOR CABLE(1) PROVIDED
POWER IN 12 VDC250 mA
ZONE ALERT LED
5.90 in.(150mm)
2.00 in.(51mm)
+_
FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON
FEMALE JACKAND INSERT AS SHOWN.
Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4
NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C
NC12V GND
ADHESIVE BACK PCB SUPPORT(4) PROVIDED
PEEL BACKING
TO 8 CHANNEL RECEIVERSTI-34108
FEMALE JACK
MALE PLUG
24 4-CONDUCTOR CABLE(1) PROVIDED
POWER IN 12 VDC250 mA
ZONE ALERT LED
5.90 in.(150mm)
2.00 in.(51mm)
+_
FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON
FEMALE JACKAND INSERT AS SHOWN.
Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4
NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C
NC12V GND
ADHESIVE BACK PCB SUPPORT(4) PROVIDED
PEEL BACKING
TO 8 CHANNEL RECEIVERSTI-34108
FEMALE JACK
MALE PLUG
24 4-CONDUCTOR CABLE(1) PROVIDED
POWER IN 12 VDC250 mA
ZONE ALERT LED
5.90 in.(150mm)
2.00 in.(51mm)
+_
FOR BOTH ENDS OFCONNECTOR ALIGN TABSON MALE PLUG TO SLOTSON
FEMALE JACKAND INSERT AS SHOWN.
Zone 5 Zone 6 Zone 7 Zone 8Zone 1 Zone 2 Zone 3 Zone 4
NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C NC NO C
NC12V GND
INSTALLATION INSTRUCTIONS1.
SnapadhesivebackPCBsupportsintoPCBasshown.
2.
PeelbackingfromadhesivebackPCBsupports,placePCBindesiredpositionandpressfirmly.
INSTALLATION OF STI-34188 8-ZONE RELAY BOARDAll specifications
and information shown were current as of publication and are
subject to change without notice.
STI-34188 JUNE 2012
Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone:
0800 085 1678 (UK only)E-mail: [email protected] Web:
www.sti-europe.com
Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone:
0800 085 1678 (UK only)E-mail: [email protected] Web:
www.sti-europe.com
INSTALLATION OF STI-34188 8-ZONE RELAY BOARDAll specifications
and information shown were current as of publication and are
subject to change without notice.
STI-34188 JUNE 2012
A
AFTER DRILLING, CUT OUT THIS AREAUSING SIDE CUTTERS OR KNIFE
CABLE JACK TO RELAY BOARD
DRILL 5/32 in. (4mm)DIAMETER HOLE
BE SURE TO ROUTE CABLE AROUND POST AS
SHOWN AND PLUG CABLE IN TO CONNECTOR
CIRCUIT BOARD MOUNTING SCREW
DETAIL A
ALIGN TOASSEMBLE
A
AFTER DRILLING, CUT OUT THIS AREAUSING SIDE CUTTERS OR KNIFE
CABLE JACKTO RELAY BOARD
DRILL 5/32 in. (4mm)DIAMETER HOLE
BE SURE TO ROUTE CABLE AROUND POST AS
SHOWN AND PLUG CABLE IN TO CONNECTOR
CIRCUIT BOARDMOUNTING SCREW
DETAIL A
ALIGN TOASSEMBLE
CABLE INSTALLATION TO RECEIVER1.
Removecircuitboardfrombasebyremovingcircuitboardmountingscrew.
2.
Drill5/32in.diameterholeinbaseasshown(circuitboardmustberemoved.)
3. Afterdrilling,cutoutareaasshownusingsidecuttersorknife.
4. Routecableasshownandconnectcabletojackoncircuitboard.
5.
Whilereplacingcircuitboard,gentlypullcablefrombottomofbasetotakeupanyslackincableoccurredduringinstallation.
SPECIFICATIONS Standby:12VDC;0.01mA MaxOperating:12VDC;164mA
FormCContactRating(resistive):120VAC,3A;28VDC,3A
WARRANTYOneyearwarrantyonelectromechanicalandelectroniccomponents.Electronicwarrantyformatwww.sti-usa.com/wc14.