This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
ZED-F: CAST IRON & ALUMINUM Series Pumps & Parts: Page #’s 34-38
TABLE OF CONTENTS
SPECIAL NOTE:
This Website has been designed as a aid to make it easier for you (the customer) to properly identify a particular steering unit. To identify a particular Steering Pump, it will require you to
look your steering unit over to get any Name Brand and any Numbers that can possible be found. The catalog is broke down into various sections that pertain to all of the common name brands of Steering Pumps available on the market today. If you have the Name Brand such as
Vickers, LUK & Etc., then look in the “Table of Contents” above and refer to that particular illustration section of catalog to ID. If you have the part number off of the Steering Pump itself
or the OEM number from the dealer, then please call us at (281) 386-7229.
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
Steering Rebuilders & Truck Parts, Inc. offers a variety of “Good Used” and some “New” Eaton B Reservoirs. To determine what you need, refer to pictured
illustrations below. All reservoirs (1) thru (7) are viewed from the back. Call 281-386-7229 for “Price & Availability.
Need to know:
C) CLOCKING: 3-9, 6-12 & Etc. (Viewed from
back as shown) Also see illustrations.
Need to know:
A) NIPPLE LOCATION - Left Hand (LH Side) or Right Hand (RH side) viewed from back as shown in illustration
B) NIPPLE POSITION (Viewed
from Side of Reservoir) - Pointed Up (12 o’clock), Down (6 o’clock), Front (9 o’clock) or Back (3 o’clock)
LH Side RH Side
Common “Eaton B” Reservoirs
NOTE: “Eaton B Reservoirs” supplied without “Filter Kit” & “Dip Stick”. When ordering Reservoir, be sure to include a Filter Kit #PS275 (3.5” Long) or Filter Kit #PS277 (3” Long) &
Dip Stick #ERS24926. Call (281) 386-7229 FOR “PRICE & AVAILABILITY”
BACK VIEW FRONT VIEW
BACK VIEW
Application:
IHC w/ DT466
Application:
Cummins
Application:
3208 Cat.
Clocking
Clocking Clocking Clocking Clocking
Clocking Clocking
(1) (3) (2)
(4) (5) (6) (7)
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
**When ordering this pump, You will need to order a Filter Kit to replace old one in Reservoir. To Order Filter Kit, we will need Length of Filter. Either 3” Long (SRTP #PS277) or 3.5” Long (SRTP #PS275)
GEAR DRIVE w/ 3.5” LONG THREADED NUT & KEYWAY SHAFT:
CLOCKWISE ROTATION: Front axle weight up to 14K - SRTP #600 Front axle weight 16K & up - SRTP #604
COUNTER-CLOCKWISE ROTATION: Front axle weight up to 14K - SRTP #601CCW Front axle weight 16K & up - SRTP #599CCW
**When ordering this pump, You will need to order a Filter Kit to replace old one in Reservoir. To Order Filter Kit, we will need Length of Filter. )Either 3” Long (SRTP #PS277) or 3.5” Long (SRTP #PS275)
CLOCKWISE ROTATION: Front axle weight up to 14K - SRTP #607 Front axle weight 16K & up - SRTP #606
COUNTER-CLOCKWISE ROTATION: Front axle weight up to 14K - SRTP #603CCW Front axle weight 16K & up - SRTP #605CCW
**When ordering this pump, You will need to order a Filter Kit to replace old one in Reservoir. To Order Filter Kit, we will need Length of Filter. Either 3” Long (SRTP #PS277) or 3.5” Long (SRTP #PS275)
“CUMMINS” ENGINES
“DETROIT 6V & 8V” ENGINES
“DETROIT 6V & 8V” ENGINES
Note: All “Eaton B” Series pumps supplied with necessary O-ring & sealing washers to service reservoir.
3.5” long
4 3/8” long
3.5” long
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
Note: Certain Ford / GM models use a “Tube-O” pressure port. The standard BB uses a 3/4” - 16 O-ring Port. Pumps that need a “Tube-O” port are designated with the letter “O” as shown in “SRTP” Pump Breakdown. Omit if not
E) Shaft Type
(C1) Pressure Port
D) Return Port
D) Return Port
B) Orifice Size C) Pressure Setting
& C1) Pressure
A) Rear Housing Cover ID &
A1) Rotation:
F) MEASURE ACROSS 2 1/4” = (LV) Low Flow
2 3/4” = (HV) High Flow
NOTE: Either a Reservoir or Hose Adapter will be mounted as shown in illustration below.
(E) Shaft Types & “Low” or “High” Flow
“
A = Low Flow B = High Flow
H = Low Flow D = High Flow
E = Low Flow F= High Flow
G = Low Flow L = High Flow
J = Low Flow K = High Flow
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
Note: No Other Parts are available for “LUK” Series Pumps. If additional parts are needed, It will be necessary to Order a Remanufactured or New Pump. Call (281) 386-7229 with number
stamped / stenciled on pump.
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
“PARKER HANNIFIN” PUMPS “H39, H49, H77, H90” Series
These “Parker Hannifin” Pumps have been updated to a “Vickers” series pump. To order a updated Pump (Vickers), Look on side of Mounting Flange for Mfg. Stamped
Number. See illustration below for location of part number. Once you have this number, please call (281) 386-7229 for “Price & Availability”
COMMON “PARKER HANNIFIN” NUMBERS
H39BT2AA21540DS H90BY1CA17560DS
H49BT2AA17560DS H90BY2CA17560DS
H77BT1AA17560DS H90CY1CA17560DS
H77BT2FA17560DS H90CY2CA17560DS
H77BY2CA17560DS
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
**NOTE 1: All “Eaton” Conversion Kits are supplied with the Following Components: Remanufactured Pump, Reservoir, Dip Stick, Filter Kit, Pulley and Pump Mounting Brackets
for Engine.
**NOTE 2: Customer will have to supply his own “Belts”, “Hoses”, “Bolts” & “Fittings”.
Typical “REXROTH” Typical “EATON B”
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
“SAGINAW” PUMPS “BIG BEARING” & “BUSHING / SEAL” TYPE
w/o RESERVOIR
5 1/4”
2”
3/4
1”
2”
5 1/4”
5 1/4”
1 1/2”
3/4” Offset Bolt Hole (Note: Measure from outside edge to center of bolt hole)
1” Offset Bolt Hole (Note: Measure from outside edge to center of bolt hole)
Note: It maybe necessary to re-use old pressure fitting due to (2) different sizes being used. See “Pressure Fitting” illustration above.
Big Bearing / Snap Ring
Bushing / Seal Type
SRTP PART #800 NOTE: “Saginaw” pumps supplied with necessary o-rings to service reservoir.
SRTP PART #801 NOTE: “Saginaw” pumps supplied with necessary o-rings to service reservoir.
SRTP PART #900 NOTE: “Saginaw” pumps supplied with
necessary o-rings to service reservoir.
Big Bearing / Snap Ring
Typical “Saginaw Pumps” w/ Res-ervoir shown below. These pumps are shown for Identification pur-poses only. If you need a Pump w/ Reservoir. See next page or order a Reman. w/o Reservoir as shown on right hand side of this page.
Typical “Saginaw Pumps” w/ Res-ervoir shown below. These pumps are shown for Identification pur-poses only. If you need a Pump w/ Reservoir. See next page or order a Reman. w/o Reservoir as shown on right hand side of this page.
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
NOTE: Only certain Part Numbers are available “New”. Call (281) 386-7229 with part number to check Availability. If Part # is not available in “New”, Then inquire about
purchasing a Remanufactured Pump. All Remanufactured Pumps are supplied without the
Reservoir. See previous page for Remanufactured pumps.
SRTP # 7840097
Illustration (1)
Illustration (2) Illustration (3) This style of pump is commonly found on Various Chevy / GMC Applications & IHC. DT466 Engines. IHC. #488787C91
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
Reservoir Assembly: #5688105 Used w/ SRTP Pump #’s:
7841933 & 7840009
Steering Rebuilders & Truck Parts, Inc. offers a variety of “GOOD USED” and “NEW” SAGINAW RESERVOIRS. Unfortunately we are only able to offer just a hand full of the many different styles that were once made. Use the illustrations below to see if we have what you need. We will need to know the (7) or (8) digit Mfg. Stamped number or Number off of White Tag located on back or side of Reservoir. Look where the BOLD ARROWS are pointing. All
reservoirs are viewed from the back. CALL (281) 386-7229 for Price & Availability.
IILLUSTRATION (F)
Reservoir Assembly: #7827542 Used w/ SRTP Pump #:
7840087
IILLUSTRATION (E) IILLUSTRATION (D)
IILLUSTRATION (C) IILLUSTRATION (A)
Reservoir Assembly: #7835872 Used w/ SRTP Pump #:
7840124
IILLUSTRATION (B)
Reservoir Assembly: #7830689 Used w/ SRTP Pump #:
7847871
Reservoir Assembly: #7812120 Used w/ SRTP Pump #:
7840113
Reservoir Assembly: #7837049 Used w/ SRTP Pump #:
7840097 & 7840127
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
Note: No Other Parts are available for “EV & PS” Series Pumps. If additional parts are needed, It will be necessary to Order a Remanufactured or New Pump.
Call (281) 386-7229 with Mfg. Number stamped or stenciled on pump. See Page #28 “TRW PUMPS” for info on where to locate Part Number.
1 - Housing 8 - O-ring 15 - Pins
2 - Shaft Seal 9 - Spring 16 - Cam Ring
3 - Valve Assy. 10 - Pres. Plate 17 - O-ring
4 - Spring 11 - O-ring 18 - End Cover
5 - O-ring 12 - Rotor 19 - Bolts
6 - Plug 13 - Vanes 20 - Orifice
7 - Shaft 14 - E Ring 21 - Snap Ring
Typical “EV & PS” Pump Parts Breakdown
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.
UNIT SERIES #’s 7673900##, 7673955##, 7674900##, 7674955##, 7674974## & 7677955##
NOTE 1: To Order Parts, We will need to know the Mfg. Stamped / Stenciled Number off of the Metal Tag affixed to side of pump. See Page #34 “ZF LENKSYSTEME” PUMPS “CAST IRON
TYPE” on where to locate Part Number.
NOTE 2: No Other Parts are available for “ZF Lenksysteme” Series Pumps. If additional parts are needed, It will be necessary to Order a Remanufactured or New Pump. Call
(281) 386-7229 with number stamped on metal tag.
Typical “ZF” Pump Parts Breakdown
UNIT SERIES (TAG NUM.)
PART TYPE
SRTP NUMBER
UNIT SERIES (TAG NUM.)
PART TYPE
SRTP NUMBER
7673900### Seal Kit 8814 7674955### Seal Kit 8815
7673955### Seal Kit 8820 7674974### Seal Kit 8812
7674900### Seal Kit 8815 7677955### Seal Kit 8813
All #’s Cartridge Assy.
Call 281/386-7229 for “P&A”
All #’s Drive Shaft Call 281/386-7229 for ”P&A”
“S.R.T.P., INC” STEERING REBUILDERS & TRUCK PARTS, INC.