B1 Steel City ® Spring Steel Fasteners Technical Information ..........................................................................B2 Catalogue Numbering System .............................................................B3 Beams, Purlin and Hangers .........................................................B4–B10 Conduit and Cable.....................................................................B11–B19 Stud Wall & Drywall. .................................................................B20–B28 Acoustical Tee ...........................................................................B29–B34 Low Voltage / Telecommunication .............................................B35–B38 Accessories ..............................................................................B39–B41 Cross Reference .......................................................................B42–B48 Table of Contents www.tnb.ca
48
Embed
Steel City Spring Steel Fasteners - Cesco.comBeam, Purlin and Hangers Fig . 1 • Clips fit most bulb tees and beamt flanges • 1/4 in. hole provided • Installs easily with a hammer
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
B1
Steel City® Spring Steel Fasteners
Technical Information ..........................................................................B2
Catalogue Numbering System .............................................................B3
Beams, Purlin and Hangers .........................................................B4–B10
Conduit and Cable.....................................................................B11–B19
The following materials are used for Steel City Spring Steel Fasteners:
High Carbon Spring Steel
Spring steel products are manufactured using high carbon, cold rolled steel, AISI C1075 orequivalent. The final part is heat treated to give the formedproduct great resilience and strength.
Low Carbon Steel
Mild steel products are manufactured using low carbon, cold rolled steel, AISI C1008 or equivalent.Such parts receive an application of zinc or paint to protect the finished product.
Zinc Phosphate
The Zinc Phosphate finish is per MIL-SPEC-16232, type Z. This finish includes a Zinc Phosphate base with a supplementary sealant applied.The finished product will withstand 24 to 72 hours of saltspray testing in accordance with ASTM B117.
Pre-Galvanized
Products receiving a Pre-Galvanized finish are Low Carbon Steel products with a coating of Zinc applied to the Steel prior to part fabrication.This finish is in conformance with ASTM A525.
Electro-Galvanized
The Electro-Galvanized finish is a Zinc finish which includes an electro-plated layer of Zinc and then a Zinc Chromate. This finish is appliedafter fabrication and is in conformance with ASTM B633.
Painted
Some products in the Steel City line receive a Painted finish. Parts are painted for applications which require alternate colours to the standardblack Zinc Phosphate (such as acoustical ceilings).
Material
Technical Information
Load RatingsThe Steel City Spring Steel Fasteners products shown in this catalogue have a load limit based on the following:
Static Load Limit
Such products show the load limit which is based on a safety factor of 3.
Ultimate Static Load Limit
Such products show the load limit which is the highest load allowed.
These Load Limits apply only to catalogue numbers which list such a limit. For both instances, the static load limitsapply only in the orientation described in the catalogue or instruction sheet. These loads apply only to the fastener,the structure to which it will be attached must be evaluated separately.
w w w . t n b . c a
B3
Steel City® Spring Steel Fasteners
Individual Part Numbering SystemSSF - H A 1/4 T
1. Catalogue numbers will be preceded by an “SSF” to signify it is a Spring Steel Fastener part and to give it a uniquecatalogue number. Non-Spring Steel Fastening items in this catalogue are not preceded by SSF.
2. This portion of the catalogue number is a one letter index based on the category the product falls in. For this example, “H” is used for theHangers category. The following is a list of all the categories and their one letter index:
B — Beams and Purlin
H — Hangers
C — Conduit and Cable
S — Stud Wall and Drywall
T — Acoustical Tee
V — Low Voltage / Telecom
M — Miscellaneous
3. This portion of the catalogue number references the style in a given category. For this example, “A” is used for the rod and wire hanger withthread impressions.
4. This portion of the catalogue number is numeric and will be based on the size or range of sizes the part will fit.For example, the SSF-HA1/4T is a hanger that fits 1/4 in. threaded rod, so the numeric code would be 1/4.
5. A final letter may be but will not always be included after the numeric code. This final letter indicates one of the following:
S — the part has an attached stud
T — the part has a thread impression
A — adjustable
Riveted Combinations
SSF - B V1/4 - A3/8
1. As with the individual parts, riveted combinations will always be preceded by an “SSF” to signify it as a Spring Steel Fastener part.
2. This portion of the catalogue number, as with the individual part, is a one letter index based on the category of theproduct. For this example, “B” is used for the Beams and Purlin category. (See listing above.)
3. Riveted combinations of two parts will have a catalogue number constructed from the two individual catalogue numbers. This portion of thecatalogue number references the style and numeric size or range for the first piece of the combination (see #3 and #4 under the IndividualPart Numbering System). Note that the first part in the combination will have the same category as the combination. In this example, V1/4represents a vertical flange or C-purlin clip with an individual catalogue number of SSF-BV1/4.
4. This portion of the catalogue number references the style and numeric size or rangefor the second piece of the combination (see #3 and #4 under the Individual Part Numbering System). In this example, the A3/8 representsthe rod hanger with an individual catalogue number of SSF-HA3/8.
1 2 3 4 5
1 2 3 4
Catalogue Numbering System
w w w . t n b . c a
B4
Steel City® Spring Steel Fasteners
Fig. 4 Fig. 5
• Fits beam flanges to 1/2 in.
• Supports 1/4 in. and 3/8 in. threaded rod, s-hooks,electrical boxes, conduit andbridle rings• 1/4 in.-20 or #10-24 threaded openings
• Fits beam flanges to 1/2 in.
• Supports 1/4 in. and 3/8 in. threaded rod, s-hooks, electrical boxes, conduit and bridle rings• 1/4 in.-20 or #10-24 threaded openings
Fig. 1 Fig. 2
Fig. 3
* UL/cUL not applicable
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Beam Clamps
SSF-BBC 1 Stamped steel beam clamp 100 100
SSF-BBC-S1/2V* 2Beam clamp thru 1/2 in. flangeto conduit clamp, 1/2 in. conduit
25 25
SSF-BBC-S3/4V* 2Beam clamp thru 1/2 in. flangeto conduit clamp, 3/4 in. conduit
25 25
SSF-BBC-S1V* 2Beam clamp thru 1/2 in. flangeto conduit clamp, 1 in. conduit
25 25
SSF-BBC-S1/2H* 3Beam clamp thru 1/2 in. flange to sidemounted conduit clamp, 1/2 in. conduit
15 25
SSF-BBC-S3/4H* 3Beam clamp thru 1/2 in. flange to sidemounted conduit clamp, 3/4 in. conduit
15 25
SSF-BBC-S1H* 3Beam clamp thru 1/2 in. flange to sidemounted conduit clamp, 1 in. conduit
15 25
Beams, Purlin and Hangers
Features Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Beam Clamps
SSF-BBC-C1/2 3/4V 4 Beam clamp thru 1/2 in. flange toconduit clamp, 1/2 in.-3/4 in. conduit 100
25
SSF-BBC-C1V 4 Beam clamp thru 1/2 in. flange toconduit clamp, 1 in. conduit 100
SSF-BBC-C1 1/4V 4 Beam clamp thru 1/2 in. flange toconduit clamp, 1-1/4 in. conduit 100
SSF-BBC-C1 1/2V 4 Beam clamp thru 1/2 in. flange toconduit clamp, 1-1/2 in. conduit 100
SSF-BBC-C2V 4 Beam clamp thru 1/2 in. flange toconduit clamp, 2 in. conduit 100
SSF-BBC-C1/2 3/4H 5Beam clamp thru 1/2 in. flange toside mounted conduit clamp,1/2 in.-3/4 in. conduit
• Clips fit most bulb tees and beam flanges• 1/4 in. hole provided
• Installs easily with a hammer
Fig. 2
Fig. 1
• Hangs on box from the underside orto the front of beam flanges
• When used with combinationconduit hanger, the conduit run lines up with “knock-outs” in outlet box and eliminates offsets and bends
• 1/4 in.-20 threaded opening
• Also available with staked stud,1/4 in.-20 x 3/8 in. to provideeasier attachment of outlet boxesto beams. Eliminates having to use loose screws.• Supports 100 lb. static verticalload limit
• Used to suspend #8 wire, 1/4 in.,3/8 in. plain rod or 1/4 in. or3/8 in. threaded rod from beamflanges 1/8 in. to 3/4 in. thick
• Supports 200 lb. static load limit• Installs easily with a hammer
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Plain and Threaded Rod Hangers
SSF-HB8-F1/4 1 Rod/wire to beam hanger,1/8 in.-1/4 in. flange, #8 wire
200 25
SSF-HB8-F1/2 1 Rod/wire to beam hanger,5/16 in.-1/2 in. flange, #8 wire
SSF-HB8-F3/4 1 Rod/wire to beam hanger,9/16 in.-3/4 in. flange, #8 wire
SSF-HB1/4-F1/4 1 Rod/wire to beam hanger,1/8 in.-1/4 in. flange, 1/4 in. plain rod
SSF-HB1/4-F1/2 1 Rod/wire to beam hanger,5/16 in.-1/2 in. flange, 1/4 in. plain rod
SSF-HB1/4-F3/4 1 Rod/wire to beam hanger,9/16 in.-3/4 in. flange, 1/4 in. plain rod
SSF-HB3/8-F1/4 1 Rod/wire to beam hanger,1/8 in.-1/4 in. flange, 3/8 in. plain rod
SSF-HB3/8-F1/2 1 Rod/wire to beam hanger,5/16 in.-1/2 in. flange, 3/8 in. plain rod
SSF-HB3/8-F3/4 1 Rod/wire to beam hanger,9/16 in.-3/4 in. flange, 3/8 in. plain rod
SSF-HA1/4-F1/4T 2 Hammer-on rod hanger, 1/8 in.-1/4 in.flange, 1/4 in. threaded rod
SSF-HA1/4-F1/2T 2 Hammer-on rod hanger, 5/16 in.-1/2 in.flange, 1/4 in. threaded rod
SSF-HA1/4-F3/4T 2 Hammer-on rod hanger, 9/16 in.-3/4 in.flange, 1/4 in. threaded rod
SSF-HA3/8-F1/4T 2 Hammer-on rod hanger, 1/8 in.-1/4 in.flange, 3/8 in. threaded rod
SSF-HA3/8-F1/2T 2 Hammer-on rod hanger, 5/16 in.-1/2 in.flange, 3/8 in. threaded rod
SSF-HA3/8-F3/4T 2 Hammer-on rod hanger, 9/16 in.-3/4 in.flange, 3/8 in. threaded rod
SSF-HA3/8-F1/4 2 Rod/wire to beam hanger, 1/8 in.-1/4 in.flange, 1/4 in. or 3/8 in. threaded rod
SSF-HA3/8-F1/2 2 Rod/wire to beam hanger, 5/16 in.-1/2 in.flange, 1/4 in. or 3/8 in. threaded rod
SSF-HA3/8-F3/4 2 Rod/wire to beam hanger, 9/16 in.-3/4 in.flange, 1/4 in. or 3/8 in. threaded rod
Fig. 1
Hangers
w w w . t n b . c a
B10
Steel City® Spring Steel Fasteners
Fig. 3 Fig. 4Fig. 1 Fig. 2
*UL and cUL not applicable
• Accepts strap widths upto 1-1/8 in.
• Can be attached to a wide variety of products
• Supports 100 lb. static load limit• Clips are made from galvanizedsteel
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Strap Hanger Clips
SSF-HS 1 Strap hanger clip
200
100SSF-HR 2 Strap hanger clip, right angle
SSF-HR-F1/4 3 Strap hanger clip, right angle,1/8 in. -1/4 in. flange thickness
25
SSF-HR-F1/2 3 Strap hanger clip, right angle,5/16 in. -1/2 in. flange thickness
SSF-HR-F3/4 3 Strap hanger clip, right angle,9/16 in. -3/4 in. flange thickness
SSF-HS-F1/4 4 Strap hanger clip, flange thickness1/8 in. -1/4 in.
SSF-HS-F1/2 4 Strap hanger clip, flange thickness5/16 in. -1/2 in.
SSF-HS-F3/4 4 Strap hanger clip, flange thickness5/16 in. -3/4 in.
Beams, Purlin and Hangers
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Miscellaneous Hangers
SSF-HB8 1 Rod & wire hanger, #8 wire
160 100
SSF-HB1/4 1 Rod & wire hanger, 1/4 in. plain rod
SSF-HB3/8 1 Rod & wire hanger, 3/8 in. plain rod
SSF-HA3/8 2 Rod & wire hanger 1/4 in. -3/8 in.threaded rod, nuts required
SSF-HA1/4T 2 Rod & wire hanger with threadimpression 1/4 in. threaded rod
SSF-HA3/8T 2 Rod & wire hanger with threadimpression 3/8 in. threaded rod
SSF-HOB 3 Offset bracket with 1/4 in. hole
SSF-HAB 4 Angle bracket with 1/4 in. hole
SSF-HSAB 5 Short angle bracket with 1/4 in. hole
SSF-HFB 6 Flat bracket with 1/4 in. hole
SSF-MA7* 7 For T-grid, with 1 in.snap-in conduit clip
• Rod hanger without threadimpression available for1/4 in. and 3/8 in. threaded rod
Features
Fig. 5 Fig. 7Fig. 6
Fig. 2 Fig. 3 Fig. 4Fig. 1
Hangers
w w w . t n b . c a
B11
Steel City® Spring Steel Fasteners
Fig. 1
Conduit and Cable
• Available for3/8 in. through2 in. trade sizesfor EMT, flexibleconduit andMC/AC cable
• Available with eithera plain hole for 1/4in. bolt or a 1/4 in.-20thread impression
Features• Available for 1/2 in. through 1 in. EMT andrigid conduit
• Available with either a plain hole for 1/4 in.bolt or a 1/4 in.-20 thread impression
• Supports ultimate static load limit 25 lb. inthe vertical position. Supports ultimatestatic load limit 15 lb. in the horizontalposition.
Features
No tools needed!Finger friendly
design!
Fig. 1
Cat. No.Fig.No.
ConduitSize
MountingHole
Qty.Per Box
Conduit Clips
SSF-CC3/8 1 14-2 thru 12-3 MC/AC Cableand 3/8 in. Conduits
9/32 in. Plain
100
SSF-CC1/2 3/4 1 1/2 in. -3/4 in.
SSF-CC1 1 1 in.
SSF-CC1 1/4 1 1-1/4 in.
SSF-CC1 1/2 1 1-1/2 in.
SSSF-CC2 1 2 in.
SSF-CC3/8T 1 14-2 thru 12-3 MC/AC Cableand 3/8 in. Conduits
1/4 in.-20Thread impression
SSF-CC1/2 3/4T 1 1/2 in. -3/4 in.
SSF-CC1T 1 1 in.
SSF-CC1 1/4T 1 1-1/4 in.
SSF-CC1 1/2T 1 1-1/2 in.
SSF-CC2T 1 2 in.
• Shape of clip and clasp mechanism allowsfor hand installation (no tools needed)
• Unique clasp design has an aggressively angledtab and receiving hole to provide consistent,easy clasping of the clip
• Supports 100 lb. static load limit in the vertical position.Supports 25 lb. static load limit in the horizontal position.
• Unique finger grips on the ends of the clip provide easy grip forhand installation, or easy grip of pliers when using pliers to install
Cat. No.Fig.No.
ConduitSize (in.)
MountingHole
Qty.Per Box
Conduit Clips
SSF-CS1/2 1 1/2
9/32 in. Plain
100
SSF-CS3/4 1 3/4
SSF-CS1 1 1
SSF-CS1/2T 1 1/21/4 in.-20
Thread impressionSSF-CS3/4T 1 3/4
SSF-CS1T 1 1
Conduit Supports
w w w . t n b . c a
B12
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2
Fig. 1
Conduit and Cable
• Available with Spring Steel Conduit Clip bottom mounted or side mounted
• Available for 3/8 in. through 2 in. trade sizes for EMT, rigid, flexible conduit and MC/AC cable
• Fits beam flanges 1/8 in. through 3/4 in. thick• Will pivot through 360°• Fig. 1 supports 75 lb. static load limit• Fig. 2 supports 25 lb. static load limit
• Installs easily with a hammerand pliers
Features
Cat. No.Fig. No. 1
Cat. No.Fig. No. 2
DescriptionQty.
Per Box
Flange Mount Conduit Clips
SSF-CC3/8-H1/4 SSF-CC3/8-F1/4 14-2 thru 12-3 MC/AC cable and 3/8 in. conduitsto 1/8 in. to 1/4 in. flanges and 3/8 in. conduits
25
SSF-CC1/2 3/4-H1/4 SSF-CC1/2 3/4-F1/4 1/2 in. conduit to 3/4 in. conduitto 1/8 in. to 1/4 in. flanges
SSF-CC1-H1/4 SSF-CC1-F1/4 1 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CC1 1/4-H1/4 SSF-CC1 1/4-F1/4 1-14 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CC1 1/2-H1/4 SSF-CC1 1/2-F1/4 1-12 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CC2-H1/4 SSF-CC2-F1/4 2 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CC3/8-H1/2 SSF-CC3/8-F1/2 14-2 thru 12-3 MC/AC cable and 3/8 in. conduits to 5/16 in. to 1/2 in. flanges
SSF-CC1/2 3/4-H1/2 SSF-CC1/2 3/4-F1/2 1/2 in. conduit to 3/4 in. conduitto 5/16 in. to 1/2 in. flanges
SSF-CC1-H1/2 SSF-CC1-F1/2 1 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CC1 1/4-H1/2 SSF-CC1 1/4-F1/2 1-14 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CC1 1/2-H1/2 SSF-CC1 1/2-F1/2 1-12 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CC2-H1/2 SSF-CC2-F1/2 2 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CC3/8-H3/4 SSF-CC3/8-F3/4 4-2 thru 12-3 MC/AC cable and 3/8 in. conduits to 9/16 in. to 3/4 in. flanges
SSF-CC1/2 3/4-H3/4 SSF-CC1/2 3/4-F3/4 1/2 in. conduit to 3/4 in. conduitto 9/16 in. to 3/4 in. flanges
SSF-CC1-H3/4 SSF-CC1-F3/4 1 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CC1 1/4-H3/4 SSF-CC1 1/4-F3/4 1-1/4 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CC1 1/2-H3/4 SSF-CC1 1/2-F3/4 1-1/2 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CC2-H3/4 SSF-CC2-F3/4 2 in. conduit to 9/16 in. to 3/4 in. flanges
Fig. 2
• Available with Spring Steel Conduit Clip bottom mounted or side mounted
• Available for 1/2 in. through 1 in. EMTand rigid conduit
• Fits beam flanges 1/8 in. through 3/4 in. thick.• Will pivot 360°• Fig. 1 supports 25 lb. static load limit• Fig. 2 supports 15 lb. static load limit• Requires only hammer to install
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Flange Mount Snap-in Conduit Clips
SSF-CS1/2-H1/4 1 1/2 in. conduit to 1/8 in. to 1/4 in. flanges
25
25
SSF-CS3/4-H1/4 1 3/4 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CS1-H1/4 1 1 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CS1/2-H1/2 1 1/2 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS3/4-H1/2 1 3/4 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS1-H1/2 1 1 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS1/2-H3/4 1 1/2 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CS3/4-H3/4 1 3/4 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CS1-H3/4 1 1 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CS1/2-F1/4 2 1/2 in. conduit to 1/8 in. to 1/4 in. flanges
15
SSF-CS3/4-F1/4 2 3/4 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CS1-F1/4 2 1 in. conduit to 1/8 in. to 1/4 in. flanges
SSF-CS1/2-F1/2 2 1/2 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS3/4-F1/2 2 3/4 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS1-F1/2 2 1 in. conduit to 5/16 in. to 1/2 in. flanges
SSF-CS1/2-F3/4 2 1/2 in. conduit to 9/16 in. to 3/4 in. flanges
SSF-CS3/4-F3/4 2 3/4 in. conduit to 5/16 in. to 3/4 in. flanges
SSF-CS1-F3/4 2 1 in. conduit to 5/16 in. to 3/4 in. flanges
Conduit Supports
w w w . t n b . c a
B13
Steel City® Spring Steel Fasteners
Fig. 1
New finger friendlydesign and exclusive
center slot keeps dropwire centered.
Fig. 1
Fig. 2 Fig. 3
Conduit and Cable
FROM DROP WIRE OR FLANGE• Attaches to #12 wire through 3/8 in. rod.• Fits 1/8 in. to 3/8 in. flanges• Provides attachment of conduit and boxes.• Supports #10-24 and 1/4 in.-20 threaded bridle rings
• Assemblies to support 1/2 in., 3/4 in.and 1 in. EMT and rigid conduit
• Also attaches to 1/4 in. and 3/8 in.threaded rod
Features• Exclusive slot keeps drop wirecentered
• Will not bend or deform drop wire• Delivers faster installation• Supports MC/AC, 14-2 through 12-3 cable and 1/2 in. EMT (0.433 in.-0.706 in. O.D.) from#8-#12 wire and 1/4 in. plain andthreaded rod
• Eliminates the need to trapcable against drop wire
• Supports 25 lb. static load limit• No tools required
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Multi-Function Utility Clip from Drop Wire or Flange
SSF-CUC 1 Multi-function utility clip 50 100
SSF-CUC-S1/2 2 Utility clip to 1/2 in. conduit 15 25
SSF-CUC-S3/4 2 Utility clip to 3/4 in. conduit 15 25
SSF-CUC-S1 2 Utility clip to 1 in. conduit 15 25
SSF-CUC-C1/2 3/4 3 Utility clip to 1/2 in. or 3/4 in. conduit 25 25
SSF-CUC-C1 3 Utility clip to 1 in. conduit 25 25
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Cable from Drop Wire Support
SSF-CB706 1 Cable from drop wire support 25 100
w w w . t n b . c a
B14
Steel City® Spring Steel Fasteners
FIG. 1
FIG. 1 FIG. 2
B
C
A
Conduit and Cable
Cat. No.Fig.No.
DescriptionQty.
Per Box
Conduit Hangers from Flange, Wire or Rod
SSF-CK1/2 1 Conduit hangers for flange wire or rod
100SSF-CK3/4 1 Conduit hangers for flange wire or rod
SSF-CK1 2 Conduit hangers for flange wire or rod
ConduitSize
#10  Wire
#8 	 Wire
3/16 in. Plain Rod
1/4 in. Plain &Threaded Rod
3/8 in. Plain &Threaded Rod
Wire/Rod
1/2 EMT CK1/2 CK1/2 CK1/2 CK1/2 CK3/4
1/2 Rigid CK1/2 CK1/2 CK1/2 CK3/4 CK3/4
3/4 EMT CK3/4 CK3/4 CK3/4 CK3/4 CK1
3/4 Rigid CK3/4 CK3/4 CK3/4 CK1 CK1
1 EMT – CK1 CK1 CK1 CK1
1 Rigid – CK1 CK1 CK1 –
ConduitSize
1/8 in. Flange
3/16 in. - 1/4 in. Flange
5/16 in. - 3/8 in. Flange
7/16 in. - 1/2 in. Flange
Flange
1/2 EMT CK1/2 CK1/2 CK3/4 CK3/4
1/2 Rigid CK1/2 CK3/4 CK3/4 CK1
3/4 EMT CK3/4 CK3/4 CK1 CK1
3/4 Rigid CK3/4 CK1 CK1 CK1
1 EMT CK1 CK1 CK1 CK1
1 Rigid CK1 CK1 – –
FROM DROP WIRE• One-piece construction• Can be used in vertical or horizontal (0.433-0.535 outer diameter)
• No load rating for positioning only• No installation tools required
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Flexible Conduit Hangers from Drop Wire
SSF-CK535 1 Flexible conduit hanger from drop wire,#8-#12 wire, 0.433-0.535 O.D. cable 100
• CK Series attaches conduit (EMT, Rigid, ENT and Aluminum) to drop wire, rods or flanges
• Works with MC and AC cabldimensions 0.178 to 1.250
• Snaps easily onto flange• Cable snaps right into fastener• No load rating. For positioning only.• Installs easily with a hammer
Features
Cat. No.Fig.No.
CableO.D. (in.)
FlangeThickness (in.)
Qty.Per Box
Cable Snap Clip
SSF-CES218 1 0.178 – 0.218 1/16 – 3/16
100
SSF-CES281 1 0.218 – 0.276 1/16 – 3/16
SSF-CES375 1 0.312 – 0.375 1/16 – 3/16
SSF-CES437 1 0.375 – 0.437 1/16 – 3/16
SSF-CES562 1 0.468 – 0.562 1/16 – 3/16
SSF-CES718 1 0.600 – 0.718 1/16 – 3/16
SSF-CES937 1 0.750 – 0.937 1/16 – 3/16
SSF-CES1250 1 0.968 – 1.250 1/16 – 3/16
SSF-CEM218 1 0.178 – 0.218 3/16 – 9/32
SSF-CEM281 1 0.218 – 0.276 3/16 – 9/32
SSF-CEM375 1 0.312 – 0.375 3/16 – 9/32
SSF-CEM437 1 0.375 – 0.437 3/16 – 9/32
SSF-CEM562 1 0.468 – 0562 3/16 – 9/32
SSF-CEM718 1 0.600 – 0.718 3/16 – 9/32
SSF-CEM937 1 0.750 – 0.937 3/16 – 9/32
SSF-CEM1250 1 0.968 – 1.250 3/16 – 9/32
SSF-CEL218 1 0.178 – 0.218 5/16 – 1/2
SSF-CEL281 1 0.218 – 0.276 5/16 – 1/2
SSF-CEL375 1 0.312 – 0.375 5/16 – 1/2
SSF-CEL437 1 0.375 – 0.437 5/16 – 1/2
SSF-CEL562 1 0.468 – 0.562 5/16 – 1/2
SSF-CEL718 1 0.600 – 0.718 5/16 – 1/2
SSF-CEL937 1 0.750 – 0.937 5/16 – 1/2
SSF-CEL1250 1 0.968 – 1.250 5/16 – 1/2
SSF-CF1/8 2 0.200 – 0.468 1/8 – 1/4
SSF-CF3/8 2 0.276 – 0.600 5/16 – 7/16
SSF-CAXL1 3 Snap clip adapter 1/2 – 5/8
SSF-CAXL2 3 Snap clip adapter 5/8 – 3/4
• Provides quick attachment for MC or ACcable to metal stud
• No load rating. For positioning only.• No tools required
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Flexible Conduit to Metal Stud
SSF-CM535 1MC/AC cable to metal stud clip,
14-2 thru 12-3 cable (0.433 in. -0.535 in. O.D.)100
w w w . t n b . c a
B16
Steel City® Spring Steel Fasteners
Fig. 1
Conduit and Cable
• Effectively supports 3 runs (CW3) or 6 runs (CW6) of MC/AC cable. Also can be used to support all types of low voltage cabling as a bridle ring would.
• Locking hook contains cables inside the loop
Features• Back-to-back conduit clips forindividual use or use as lightweight trapeze
• Available for 3/8 in. through 2 in.sizes for EMT, rigid, flexibleconduit and MC/AC cable
• For use as lightweight trapeze.Total load limit is 100 lb.
• Clips for vertical use, static loadlimit 100 lb.
• No screws or bolts
Features
Cat. No. Fig.No.
No. of Runs ofMC/AC Cable
InnerDiameter (in.)
UltimateStatic Load
Limit
Qty.PerBox
Flexible Conduit and Cable Hanger
SSF-CW3 1 3 1-1/8 20100
SSF-CW6 1 6 1-3/4 50
Fig. 3 Fig. 4
Cat. No.Fig.No.
DescriptionQty.
Per Box
Lightweight Trapeze
SSF-CC1-C3/8 3 Back-to-back conduit clips,14-2 thru 12-3 MC/AC to 1 in. conduit
25
SSF-CC1-C1/2 3/4 3 Back-to-back conduit clips,1/2 in. or 3/4 in. conduit to 1 in. conduit
SSF-CC1-C1 3 Back-to-back conduit clips,1 in. conduit to 1 in. conduit
SSF-CC1-C1 1/4 3 Back-to-back conduit clips,1-1/4 in. conduit to 1 in. conduit
SSF-CC1-C1 1/2 3 Back-to-back conduit clips,1-1/2 in. conduit to 1 in. conduit
SSF-CC1-C2 3 Back-to-back conduit clips,2 in. conduit to 1 in. conduit
SSF-CC1/2 3/4-C1/2 3/4* 3 Back-to-back conduit clips,1/2 in. or 3/4 in. conduit
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Conduit To Conduit Clips
SSF-CS1/2-S1/2* 4 Back-to-back snap-in conduit clip,1/2 in. to 1/2 in. EMT or rigid
25 25
SSF-CS1/2-S3/4* 4 Back-to-back snap-in conduit clip,1/2 in. to 3/4 in. EMT or rigid
SSF-CS1/2-S1* 4 Back-to-back snap-in conduit clip,1/2 in. to 1 in. EMT or rigid
SSF-CS3/4-S3/4* 4 Back-to-back snap-in conduit clip,3/4 in. to 3/4 in. EMT or rigid
SSF-CS3/4-S1* 4 Back-to-back snap-in conduit clip,3/4 in. to 1 in. EMT or rigid
SSF-CS1-S1* 4 Back-to-back snap-in conduit clip,1 in. to 1 in. EMT or rigid
* UL and cUL not applicable
w w w . t n b . c a
B17
Steel City® Spring Steel Fasteners
Conduit and Cable
• Clips available for 1, 2, or 4 cable runs• The standard CR2 part can be broken apart to create 2 single cable run clips
• Mounting holes available for mounting flator perpendicular to stud or flange
• Mounting clips for quick attachmentto metal studs
14-4, 12-2, 10-2, 8-214-3, 12-3, 10-3, 14-412-4 and 10-4 w/ground
4
Flexible Conduit (BX) 5/16, 3/8 4
Fig. 1
• Supports 1/2 in. and 3/4 in. EMTconduit and MC/AC cable
• Works with wood or metal stud• Preset bend provides alignment with knockouts for 1-1/2 in. deep boxes or 2-1/8 in. deep boxes
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Screw On Conduit Support
SSF-SS1/2 3/4 11/2 in. and 3/4 in. EMT conduit andMC/AC to metal or wood studFor 1-1/2 in. deep box
100
SSF-SS1/2 3/4D 11/2 in. and 3/4 in. EMT conduit, andMC/AC to metal or wood studFor 2-1/8 in. deep box
Stud Wall & Drywall
Cable Support Metal Stud
w w w . t n b . c a
B21
Steel City® Spring Steel Fasteners
* CSA and UL not applicable
Fig. 1 Fig. 3 Fig. 4Fig. 2
• Fits most electrical boxes requiringplaster rings
• Fits most metal stud sizes• Will not move on stud• Wider part for more secure fastening• No screws required• Support leg braces box against stud• Installs easily with a hammer
Features
• Provides side support for electrical boxes
• Works with most electrical boxes for 2-1/2 in., 3-1/2 in. and 4 in. metal stud depths
Features
Fig. 1Fig. 2
Fig. 3
Cat. No.Fig.No.
DescriptionQty.
Per Box
Snap On Box Clip
SSF-SMX 1 Snap on box support for mounting to stud100
SSF-SK 2 Screw to stud, box support
SSF-SK-C1/2 3/4 3 1/2 in. -3/4 in. finger close conduit clip
25
SSF-SK-C1 3 1 in. finger close conduit clip
SSF-SK-S1/2 4 1/2 in. snap-in conduit clip
SSF-SK-S3/4 4 3/4 in. snap-in conduit clip
SSF-SK-S1 4 1 in. snap-in conduit clip
Cat. No.Fig.No.
DescriptionQty.
Per Box
Far Side Box Support
SS1-TB 1 Far side box support
10050-SC* 2 Box brace for 4 in. square or octagonal box
SSF-SX 3 Electrical box support
Stud Wall & Drywall
Snap On Box Supports Far Side Box Supports
w w w . t n b . c a
B22
Steel City® Spring Steel Fasteners
• Attaches securely to most metalstud sizes
• Adjustable offset allows the boxto protrude through drywall sizes:1/4 in., 3/8 in., 1/2 in., 5/8 in.,or 3/4 in.
• Riveted to accommodate yourdrywall requirements
Features
Fig. 5Fig. 4
Fig. 2
Fig. 3
Fig. 1
* CSA not applicable
• Attaches securely to most metal stud sizes• Adjustable offset allows the box to protrude through drywall sizes: 1/4 in., 3/8 in., 1/2 in., 5/8 in., or 3/4 in.
• Riveted to accommodate your drywall requirements
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Switch Box or Conduit to Metal Stud
SSF-SFA 1Snap on box support for mounting to stud,
adjustable
25
SSF-SF0 2Snap on box support for mounting to stud,
riveted for flush to stud face
SSF-SF1/4 2Snap on box support for mounting to stud,
riveted for 1/4 in. drywall
SSF-SF3/8 2Snap on box support for mounting to stud,
riveted for 3/8 in. drywall
SSF-SF1/2 2Snap on box support for mounting to stud,
riveted for 1/2 in. drywall
SSF-SF5/8 2Snap on box support for mounting to stud,
riveted for 5/8 in. drywall
SSF-SF3/4 2Snap on box support for mounting to stud,
riveted for 3/4 in. drywall
SSF-SFT* 3Snap on box support for mounting to studwith 1/4 in. -20 thread impression
Cat. No.Fig.No.
DescriptionQty.
Per Box
Switch Box or Conduit to Metal Stud
SSF-SF-S1/2 4Snap on stud, push-in conduit clip,
1/2 in. conduit
25
SSF-SF-S3/4 4Snap on stud, push-in conduit clip,
3/4 in. conduit
SSF-SF-S1 4Snap on stud, push-in conduit clip,
1 in. conduit
SSF-SF-C3/8 5Snap on stud, conduit support clip,3/8 in. conduit or MC/AC cable
SSF-SF-C1/2 3/4 5Snap on stud, conduit support clip,
1/2 in. - 3/4 in. conduit
SSF-SF-C1 5Snap on stud, conduit support clip,
1 in. conduit
Stud Wall & Drywall
Metal Stud
w w w . t n b . c a
B23
Steel City® Spring Steel Fasteners
Fig. 3
Fig. 1 Fig. 2
• Attaches 4 in. and 4-11/16 in. electrical boxes to metal stud
• Support leg can be attached to stud to eliminate movement of box in wall
• Attaches to metal or wood stud using self tapping screws and screw gun or nails.
• One part mounts boxes for 1-1/2 in.,2-1/2 in., 3-1/2 in., 4 in. and 6 in. stud which means less inventory
• SH4, SH6, brackets available specifically for 4 in. and 6 in. studs respectively
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Mounting Bracket
SSF-SH2346 14 in. & 4-11/16 in. outlet boxes to 2-1/2 in.,
3-1/2 in. , 4 in. & 6 in. metal studs100
SSF-SH4 24 in. & 4-11/16 in. outlet boxes to
4 in. metal studs50
SSF-SH6 24 in. & 4-11/16 in. outlet boxes to
6 in. metal studs
• Self tapping screws are aligned with the dimples so that the box is straight
• Allows mounting of multiple boxes• Preset for metal stud 16 in. or 24 in.on center
• Depth set for 1-1/2 in. or 2-1/8 in. deepelectrical box
• Installs easily with a screw gun• SGP and SGA brackets have adjustable tabs for 1-1/2 in. or 2-1/8 in. deep boxes
• SGA brackets adjustable for non-standard stud spacing
Features
Cat. No.Fig.No.
DescriptionStud
SpacingBoxDepth
Qty.Per Box
Screw Gun Box Bracket
SSF-SG16A 3 Adjustable box bracket 11 in. -18 in. 1-1/2 in. or2-1/8 in.
50SSF-SG24A 3 Adjustable box bracket 17 in. -26 in.
1-1/2 in. or2-1/8 in.
Stud Wall & Drywall
Metal Stud
w w w . t n b . c a
B24
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2
Fig. 1
Fig. 2
Fig. 3
Fig. 4
• Improved bracket with bendablestabilizer leg for use on 2-1/2 in.and 3-1/2 in. metal studs
• Mounts outlet boxes 12 in. or18 in. offset from either a metalstud track or a stud
• When mounted, drywall ring isbrought to within 1/6 in. ofdrywall every time and will notbulge or break out drywall
• Mounts 4 in. or 4-11/16 in.outlet boxes, 1-1/2 in. or2-1/8 in. deep
• The SSF-S6X extender workswith SSF-SV12, SSF-SV18,SSF-SB16 and SSF-SB24 toextend stabilizer leg when using6 in. stud
Features• Supports electrical boxes, plaster rings or lowvoltage devices from one bracket
• Accommodates 4 in. or 4-11/16 in. boxes• Bendable leg serves as a bracket stabilizer• SB16F and SB24F flat versions allowmounting for any stud spacing, from4 in. to 24 in.
• SB brackets allow box mounting in all four90° orientations
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Box Mounting Brackets for Between Studs
SSF-SB16 1 Box mounting bracket for between studs,16 in. stud spacing
25SSF-SB24 2 Box mounting bracket for between studs,
24 in. stud spacing
SSF-SB16F 3 Box mounting bracket, flat version,up to 16 in. stud spacing
SSF-SB24F 4 Box mounting bracket, flat version,up to 24 in. stud spacing
Cat. No.Fig.No.
DescriptionQty.
Per Box
Extension Plate Bracket
SSF-SV12 1 Extension plate bracket, 12 in. height50
SSF-SV18 1 Extension plate bracket, 18 in. height
SSF-S6X 2 Extender for 6 in. metal studs 100
Stud Wall & Drywall
Box Brackets
w w w . t n b . c a
B25
Steel City® Spring Steel Fasteners
• Fits 2 in. x 3 in. switch boxes with one ortwo screw plaster ears
• Uses one bracket on 2-1/2 in. and 3-1/2 in.metal studs
• Bracket can be piggy-backed on same sideof metal stud (singly or any number inseries) giving greater flexibility to installer
• Brackets can be mounted on both sides of metal stud for double mounting
• Will not bulge or break out the drywall when mounted
Features
Fig. 1Fig. 1
• Mounts on metal or wood studding• Used as conduit rack or space for rigidconduit, IMC or EMT
• Ideal for schools, hospitals, industrial andcommercial jobs
• Galvanized steel
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Switch Box Braket
SSF-SHSB 1 Switch box bracket 100
Cat. No.Fig.No.
DescriptionQty.
Per Box
Floor Mounted Box Supports
7502 1 Footed box supports, 20 in. height 25
7503 SC 1 Footed box supports, 30 in. height 50
Stud Wall & Drywall
Switch Box Bracket Box Support
w w w . t n b . c a
B26
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2 Fig. 3
* UL and CSA not applicable** CSA not applicable
Fig. 2Fig. 1 Fig. 3
• Fit any size or shape metal stud hole• Provides complete 360° protectionfor cable
Features• A quick means of support for horizontalruns of conduits or MC/AC throughmetal stud
• Installs easily with a screw gun• SSF-SPI allows ENT conduit and MC/AC cable to be easily pulled through metal stud
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Easy Snap Grommet
1300* 1Plastic bushing for metal stud
1 in. trade size opening (1-11/32 in. )100
1216-EN* 2 Twist-on universal bushing for metal stud 50
CI158SSPB 3For 1-5/8 in. metal stud. Installed inside the steel
stud replacing 2 CI66-SS250
* CSA not applicable
Cat. No.Fig.No.
DescriptionQty.
Per Box
Through Stud Cable/Conduit Support
SSF-SAB-C1/2 3/4 1 1/2 in. or 3/4 in. finger close conduit clip
25SSF-SAB-C3/8** 1 Finger close conduit clip 14-2 thru
12-3 MC/AC cable and 3/8 in. conduits
SSF-SAB-S1/2* 2 Snap-in conduit clip — 1/2 in. conduit
SSF-SAB-S3/4* 2 Snap-in conduit clip — 3/4 in. conduit
SSF-SP1* 3 Supports up to 1 in. conduit 100
Stud Wall & Drywall
Metal Stud Drywall
w w w . t n b . c a
B27
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
* CSA not applicable
• Eliminates the need for an electrical box when installing low voltage Class 2 wiring
• For old work or new work
Features• Quickly attaches box through finished
drywall• For up to 1-1/2 in. thick drywall• New CI820D shipped in one piece
break-apart design• Easy to install
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Low Voltage Mounting Brackets — Screw on Support
SSF-SLV* 1 Old work or new work low voltage bracket 100
VN1* 2Nonmetallic single gang new work low
voltage bracket50
VN2* –Nonmetallic two gang new work low
voltage bracket50
VW1* 3Nonmetallic single gang old work low
voltage bracket50
VW2* –Nonmetallic two gang old work low
voltage bracket50
WBF-1* 4 Low voltage mounting bracket with screws 100
CIMB-1 5 Mounting bracket. Raised 1/2 in. 25
Cat. No.Fig.No.
DescriptionQty.
Per Box
Old Work Box Support
CI820D 2 Re-work switch box steel mountingholder for 1/2 in. dry-wall 200 sets
Stud Wall & Drywall
Drywall
w w w . t n b . c a
B28
Steel City® Spring Steel Fasteners
Fig. 2Fig. 1Fig. 1
• Use for oversized drywall openings• Prevents broken cover plates• Stops device from being pushedback in wall
• Makes floating device rigid
Features• Protects cable(s) from damage when installing drywall or paneling
• No nails or screws required• Fits all stud sizes• Both products meet requirements forCEC Rule 12-516 and 12-616
• CI66SS legs are crimped with pliers to stud to provide secure fit
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Device Leveler and Retainer
SSF-SR 1 Single gang device leveler and retainer 100
Cat. No.Fig.No.
DescriptionQty.
Per Box
Protector Plates
CI66SS 1 Protector plate for metal stud250
CI66 2 Protector plate for wood stud
Stud Wall & Drywall
Drywall Protector Plates
w w w . t n b . c a
B29
Steel City® Spring Steel Fasteners
Fig. 1
*Note: Lightolier and Calculite are registered trademarks of Lightolier, andGENLYTE Company.
• Allows positioning of fixture or box anywhereacross a 24 in. span
• Hanger comes complete with THC box mounting clip and 1/4 in.-20 screw
• Drop wire holes in tee clips allows the clips to be supported from the main structure
• Part includes dual height feature which allows 1-1/2 in. deep electrical box to be mounted flush with tile or offset 3/4 in.for plaster ring
• The series includes bar hanger, THC clip and1/4 in.-20 x 38 in. screw
Fig. 1 FIg. 2
Fig. 3 Fig. 4
Features
• Reduces installation time• Hanger comes complete with bar riveted to acoustical tee clip, additional acoustical tee clip and1/4 in.-20 screw
• Position of fixture adjustablewith span
• Solid bar for sturdier installation• Installs easily with a screwdriver
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Snap On Box Hanger
SSF-TH12 1 T-grid box hanger, 12 in. span
25
SSF-TH20 1 T-grid box hanger, 20 in. span
SSF-TH24 1 T-grid box hanger, 24 in. span
SSF-TH30 1 T-grid box hanger, 30 in. span
SSF-TH24A 2 8 in. height adjustable, 24 in. span
SSF-THC 3 Snap on fixture/box hanger mounting clip100
SSF-MH1/4-3/8C 4 1/4 in. -20 x 3/8 in. bolt combo head
Cat. No.Fig.No.
DescriptionQty.
Per Box
Suspension Bars for Lightolier® and Calculite® Series Fixtures*
SSF-TL24 1 Suspension bars for Lightolier Calculite 10
• Extra-wide base provides cable support ona flat surface, eliminating kinking, bendingand crimping
• Accommodates category 5, fiber optic cable and innerduct
• Available in 1-5/16 in. and 2 in. diameter size cable support hook
• Complies with UL, CSA, NEC and EIA/TIA requirements for structured cablingsystems
• Supports 50 lb. per hook static load limit• VJ Series cable support hook can be
snapped together with VB-10 hanger bracket without hardware or tools
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Cable Support Hook
SSF-VJ1 5/16C 1 Wide base cable support hook,1-5/16 in. diameter
10050
SSF-VJ2C 1 Wide base cable support hook,2 in. diameter
SSF-VJ1 5/16 2 Wide base cable support hook,1-5/16 in. diameter
SSF-VJ2 2 Wide base cable support hook,2 in. diameter
SSF-VB10 3 Hanger bar 100
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Cable Support Hook
SSF-VJ1 5/16-BC 4 Cable support J-hook, 1-5/16 in. dia.clamp to flanges up to 1/2 in. thick
100 25
SSF-VJ2-BC 4 Cable support J-hook, 2 in. dia.clamp to flanges up to 1/2 in. thick
SSF-VJ1 5/16-BC-AB 5 Cable support J-hook, 1-5/16 in. dia.clamp to flanges up to 1/2 in. thick
SSF-VJ2-BC-AB 5 Cable support J-hook, 2 in. dia.clamp to flanges up to 1/2 in. thick
SSF-VJ1 5/16-F1/4 6 Cable support hook, 1-5/16 in. dia.clip to 1/8 in. to 1/4 in. flange
SSF-VJ1 5/16-F1/2 6 Cable support hook, 1-5/16 in. dia.clip to 5/16 in. to 1/2 in. flange
SSF-VJ1 5/16-F3/4 6 Cable support hook, 1-5/16 in. dia.clip to 9/16 in. to 3/4 in. flange
SSF-VJ2-F1/4 6 Cable support hook, 2 in. dia.clip to 1/8 in. to 1/4 in. flange
SSF-VJ2-F1/2 6 Cable support hook, 2 in. dia.clip to 5/16 in. to 1/2 in. flange
SSF-VJ2-F3/4 6 Cable support hook, 2 in. dia.clip to 9/16 in. to 3/4 in. flange
SSF-VJ1 5/16-CH1LN 7 Cable support J-hook to raisefloor support posts
Cable Supports
w w w . t n b . c a
B36
Steel City® Spring Steel Fasteners
• Extra-wide base provides cable support on aflat surface, eliminating kinking, bending andcrimping
• Accommodates category 5, fiber optic cable and innerduct
• Available in 1-5/16 in. and 2 in. diameter sizecable support clips
• Complies with UL, CSA, NEC and EIA/TIArequirements for structured cabling systems
• Supports 100 lb. per hook static load limit• VJ Series cable support clips can be snapped together with VB-10 hanger bracket without hardware or tools
Features
Fig. 4Fig. 5
Fig. 6
Fig. 1 Fig. 2 Fig. 3
Cat. No.Fig.No.
DescriptionQty.
Per Box
Cable Support Hook
SSF-VJ1 5/16-UC 1 Cable support hook, 1-5/16 in. diameterclip to #12 drop wire thru 3/8 in. rod
25
SSF-VJ2-UC 1 Cable support hook, 2 in. diameterclip to #12 drop wire thru 3/8 in. rod
SSF-VJ1 5/16-AB 2 Cable support hook, 1-5/16 in. diameterclip rotates 360°
SSF-VJ2-AB 2 Cable support hook, 2 in. diameterclip rotates 360°
SSF-VJ1 5/16-A7 3 Cable support hook, 1-5/16 in. diameterclip to acoustical tee
SSF-VJ2-A7 3 Cable support hook, 3 in. diameterclip to acoustical tee
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Cable Support Hook
SSF-VJ1 5/16-H1/4-AB 4Cable support hook, 1-5/16 in. diameter
clip to 1/8 in. to 1/4 in. flange,rotates 360°
100 25
SSF-VJ1 5/16-H1/2-AB 4Cable support hook, 1-5/16 in. diameter
clip to 5/16 in. to 1/2 in. flange,rotates 360°
SSF-VJ1 5/16-H13/4-AB 4Cable support hook, 1-5/16 in. diameter
clip to 9/16 in. to 3/4 in. flange,rotates 360°
SSF-VJ2-H1/4-AB 4Cable support hook, 2 in. diameterclip to 1/8 in. to 1/4 in. flange,
rotates 360°
SSF-VJ2-H1/2-AB 4Cable support hook, 2 in. diameterclip to 5/16 in. to 1/2 in. flange,
rotates 360°
SSF-VJ2-H13/4-AB 4Cable support hook, 2 in. diameterclip to 9/16 in. to 3/4 in. flange,
rotates 360°
SSF-VJ1 5/16-V1/4 5 Cable support hook, 1-5/16 in. diameterclip to 3/32 in. to 9/32 in. vertical flange
SSF-VJ2-V1/4 5 Cable support hook, 2 in. diameterclip to 3/32 in. to 9/32 in. vertical flange
SSF-VJ1 5/16-A1/4 6 Cable support hook, 1-5/16 in. diameterclip to 1/6 in. to 1/4 in. Z purlin
SSF-VJ2-A1/4 6 Cable support hook, 2 in. diameterclip to 1/6 in. to 1/4 in. Z purlin
Low Voltage / Telecommunication
Cable Supports
w w w . t n b . c a
B37
Steel City® Spring Steel Fasteners
Fig. 2 Fig. 3Fig. 4
Fig. 6
Fig. 1
Fig. 7
Fig. 8
Fig. 5
Fig. 2 Fig. 3Fig. 4
Fig. 5Fig. 6
Fig. 1
Fig. 7
• Wide strap ideal for attachment of highperformance cables such as Fiber Opticand CAT 5 cables
• Pre-assembled part combinations allow quick installation to vertical and horizontal flanges, purlin, drop wire, threaded rod,and acoustical tee bar
• Can be used for single or multiple bundles.• Fully adjustable around bundle, fullyencompasses cabling
• Wide, firm bearing surface to support wire
Features• Attachment of all types of MC/AC cable andhigh performance cable such as Fiber Opticand CAT 5 cables
• Pre-assembled part combinations allowquick installation to vertical and horizontalflanges, purlin, drop wire, threaded rod, andacoustical tee bar
• The hook and loop type strap makesmounting and adjustment quick and easy
• Perfect product for applications where easyaccess to the cable bundle after installationis required
Features
Cat. No.Fig.No.
DescriptionQty.
Per Box
Deltec Tie Cable Support Fasteners
SSF-VT13-F1/4 1 13 in. Strap with 1/4 in. flange clip attachment
25
SSF-VT13-F1/2 1 13 in. Strap with 1/2 in. flange clip attachment
SSF-VT13-BC 2 13 in. Strap with beam clamp attachment
SSF-VT13-UC 3 13 in. Strap with utility clip attachment
SSF-VT13-AB 4 13 in. Strap with angle bracket attachment
SSF-VT13-V1/4 5 13 in. Strap with vertical flange clip attachment
SSF-VT13-A1/4 6 13 in. Strap with Z purlin clip attachment
SSF-VT13-A7 7 13 in. Strap with TA7 acoustical tee bar mounting attachment
SSF-VT27-F1/4 1 27 in. Strap with 1/4 in. flange clip attachment
SSF-VT27-F1/2 1 27 in. Strap with 1/2 in. flange clip attachment
SSF-VT27-BC 2 27 in. Strap with beam clamp attachment
SSF-VT27-UC 3 27 in. Strap with utility clip attachment
SSF-VT27-AB 4 27 in. Strap with angle bracket attachment
SSF-VT27-V1/4 5 27 in. Strap with vertical flange clip attachment
SSF-VT27-A1/4 6 27 in. Strap with Z purlin clip attachment
SSF-VT27-A7 7 27 in. Strap with TA7 acoustical tee bar mounting attachment
CSS-H – Strap mounting bracket
CSS-135 – Additional 13-1/2 in. Strap ties
CSS-270 – Additional 27 in. Strap ties
Low Voltage / Telecommunication
Cable Supports
w w w . t n b . c a
Cat. No.Fig.No.
DescriptionQty.
Per Box
Loop Tie Cable Support Fasteners
FO350-40-0 1 Additional 13 in. Loop Tie straps. Black
25
SSF-VL13-F1/4 2 13 in. Loop Tie with 1/4 in. flange clip attachment
SSF-VL13-F1/2 2 13 in. Loop Tie with 1/2 in. flange clip attachment
SSF-VL13-BC 3 13 in. Loop Tie with beam clamp attachment
SSF-VL13-UC 4 13 in. Loop Tie with utility clip attachment
SSF-VL13-AB 5 13 in. Loop Tie with angle bracket attachment
SSF-VL13-V1/4 6 13 in. Loop Tie with vertical flange clip attachment
SSF-VL13-A1/4 7 13 in. Loop Tie with Z purlin clip attachment
SSF-VL13-CH 8 13 in. Loop Tie with TCH acoustical tee bar mounting attachment
B38
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2
Fig. 3 Fig. 4 Fig. 5
* CSA not applicable
Fig. 2Fig. 1
• Bridle rings can be combined with theseother Steel City Spring Steel Fastener products: BBC Beam Clamp, BH SeriesFlange Clips, and TC Series AcousticalTee
• Bright zinc electro-plated finish
Features• Eliminates the need for an electrical box when installing low voltageClass 2 wiring
• For old work or new work
Features
Cat. No.Fig.No.
EyeDia.
Thread SpecificationsMax. Load
(lb.)Qty.
Per Box
Threaded Bridle Ring
SSF-VR3/4A 1 3/4 in. #10-24
Machine ScrewBridle Ring
50
100
SSF-VR1 1/4A 1 1-1/4 in. #10-24
SSF-VR1 3/4A 1 1-3/4 in. #10-24
SSF-VR1 1/4B 1 1-1/4 in. 1/4-20
SSF-VR1 5/8B 1 1-5/8 in. 1/4-20
SSF-VR 2B 1 2 in. 1/4-20
SSF-VR 4B 1 4 in. 1/4-20
SSF-VR1 5/8D 2 1-5/8 in. #14
Wood ScrewBridle Ring
75SSF-VR1 1/4D 2 1-1/4 in. #14
SSF-VR3E 2 3 in. #18
SSF-VR7/8C 2 7/8 in. #10 50
Cat. No.Fig.No.
DescriptionQty.
Per Box
Low Voltage Mounting Brackets — Screw on Support
SSF-SLV* 1 Old work or new work low voltage bracket 100
VN1* 2 Nonmetallic single gang new work low voltage bracket
50VN2* – Nonmetallic two gang new work low
voltage bracket
VW1* 3 Nonmetallic single gang old work lowvoltage bracket
VW2 – Nonmetallic two gang old work lowvoltage bracket
WBF-1* 4 Low voltage mounting bracket with screws 100
CIMB-1 5 Mounting bracket. Raised 1/2 in. 25
Low Voltage / Telecommunication
Cable Supports Low Voltage
w w w . t n b . c a
B39
Steel City® Spring Steel Fasteners
Fig. 1 Fig. 2
Fig. 3
Fig. 5Fig. 4
Fig. 2Fig. 1
• Rod hanger with or without threadimpression available for 1/4 in. and 3/8 in.threaded rod
Features• Rod hanger available for 1/4 in. and 3/8 in.threaded rod with or without threadimpression
• Various steel brackets with 1/4 in. holesand galvanized finish
Features
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Miscellaneous Hangers
F-HB8 1 Rod & wire hanger, #8 wire
160 lb. 100
SSF-HB1/4 1 Rod & wire hanger, 1/4 in. plain rod
SSF-HB3/8 1 Rod & wire hanger, 3/8 in. plain rod
SSF-HA1/4T 2 Rod & wire hanger with threadimpression 1/4 in. threaded rod
SSF-HA3/8 2 Rod & wire hanger 1/4 in. -3/8 in. threaded rod, nuts required
SSF-HA3/8T 2 Rod & wire hanger with threadimpression 3/8 in. threaded rod
Cat. No.Fig.No.
DescriptionStatic Load
LimitQty.
Per Box
Miscellaneous Hangers
SSF-HOB 1 Offset bracket with 1/4 in. hole
160100
SSF-HAB 2 Angle bracket with 1/4 in. hole
SSF-HSAB 3 Short angle bracket with 1/4 in. hole
SSF-HFB* 4 Flat bracket with 1/4 in. hole
SSF-TA7* 5 For T-grid, with 1 in. snap-in conduit clip –
*UL not applicable
Accessories
Miscellaneous Components
w w w . t n b . c a
B40
Steel City® Spring Steel Fasteners
• Provides secure positioning of pipesleeve for concrete pouring of walland floor forms
• Accommodates up to Schedule80 pipe wall thicknesses
• Installs easily with a hammer
Features• Order S-Hooks and jack chain with your Spring Steel orders to save on freight, energy, and purchase orders
Features
Fig. 1 Fig. 2Fig. 1
Fig. 2
Cat. No.Fig.No.
SleeveDia. (in.)
Description/Wall ThicknessQty.
Per Box
Pipe Sleeve Positioner
SSF-MPS 1 All dia. Pipe sleeve positioner, 5/16 in. and under