8/13/2019 STD19 - Marcação http://slidepdf.com/reader/full/std19-marcacao 1/23 STANDARD STD19 Date 2009-12-03 Issue 27 Info Class Internal Page 1(23) Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name) KM Stefan Lindblom UTDH Markku Backholm Area specialist (department acronym, name) Standard co-ordinator (department acronym, name) KMB Sverker Sundmark UTDH Iréne Klingberg The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4 Distribution: Scania and Supplier Märkning av artiklar Marking of parts Innehåll Sida Orientering .....................................................2 Ändringar från föregående utgåva .................2 1 Tillämpning ..........................................2 2 Märkning för identifiering.....................3 2.1 Varumärke...........................................3 2.2 Artikelnummer .....................................3 2.3 Datummärkning...................................3 2.4 Leverantörsnummer ............................4 2.5 Chargebeteckning ...............................4 2.6 Tilläggsmärkning .................................4 3 Markering för märkning på ritning........4 3.1 Märkningssymbol ................................4 3.2 Flera märkningar .................................5 3.3 Märkningens utförande, placering och läsriktning .....................................6 4 Angivelser i märkningsrutan................7 4.1 Positionsnummer ................................7 4.2 Antal rader ...........................................7 4.3 Märkningsmetod..................................8 4.4 Teckenhöjd, h....................................12 4.5 Varumärke, typ..................................12 4.6 Artikelnummer eller annan märkningsuppgift...............................15 4.7 Datummärkning.................................15 4.8 Leverantörsnummer ..........................19 4.9 Chargebeteckning .............................19 5 Märkningsuppgifternas ordningsföljd och fördelning....................................20 6 Utrymmesmått för märkning..............21 7 Tillhörande dokument........................23 Contents Page Introduction.................................................... 2 Changes from previous issue ........................ 2 1 General............................................... 2 2 Marking for identification purposes ..... 3 2.1 Trademark .......................................... 3 2.2 Part number ........................................ 3 2.3 Date marking ...................................... 3 2.4 Supplier number ................................. 4 2.5 Charge designation............................. 4 2.6 Supplementary marking...................... 4 3 Indication of markings on drawing ...... 4 3.1 Marking symbol................................... 4 3.2 Several markings are to be made ....... 5 3.3 The design and location of the marking and the direction in which it is read................................................. 6 4 Indications in the marking box ............ 7 4.1 Position number .................................. 7 4.2 Number of lines ................................... 7 4.3 Marking method .................................. 8 4.4 Character height, h ........................... 12 4.5 Trademark, type................................ 12 4.6 Part number or other marking infor- mation ............................................... 15 4.7 Date marking .................................... 15 4.8 Supplier number ............................... 19 4.9 Charge designation........................... 19 5 The order in which marking information is presented ................... 20 6 Size of space for markings ............... 21 7 Appurtenant documents.................... 23
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
Distribution: Scania and Supplier
Märkning av artiklar Marking of parts
Innehåll SidaOrientering.....................................................2Ändringar från föregående utgåva .................21 Tillämpning..........................................22 Märkning för identifiering.....................32.1 Varumärke...........................................32.2 Artikelnummer .....................................32.3 Datummärkning...................................32.4 Leverantörsnummer ............................42.5 Chargebeteckning ...............................42.6 Tilläggsmärkning .................................43 Markering för märkning på ritning........4
3.1
Märkningssymbol ................................43.2 Flera märkningar .................................53.3 Märkningens utförande, placering
och läsriktning .....................................64 Angivelser i märkningsrutan................74.1 Positionsnummer ................................74.2 Antal rader...........................................74.3 Märkningsmetod..................................84.4 Teckenhöjd, h....................................124.5 Varumärke, typ..................................124.6 Artikelnummer eller annan
och fördelning....................................206 Utrymmesmått för märkning..............217 Tillhörande dokument........................23
Contents PageIntroduction.................................................... 2Changes from previous issue........................ 21 General............................................... 22 Marking for identification purposes ..... 32.1 Trademark .......................................... 32.2 Part number........................................ 32.3 Date marking ...................................... 32.4 Supplier number ................................. 42.5 Charge designation............................. 42.6 Supplementary marking...................... 43 Indication of markings on drawing ...... 4
3.1
Marking symbol................................... 43.2 Several markings are to be made....... 53.3 The design and location of the
marking and the direction in which itis read................................................. 6
4 Indications in the marking box ............ 74.1 Position number.................................. 74.2 Number of lines................................... 74.3 Marking method.................................. 84.4 Character height, h ........................... 124.5 Trademark, type................................ 12
4.6 Part number or other marking infor-mation............................................... 154.7 Date marking .................................... 154.8 Supplier number ............................... 194.9 Charge designation........................... 195 The order in which marking
information is presented ................... 206 Size of space for markings ............... 217 Appurtenant documents.................... 23
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
Orientering IntroductionDenna standard omfattar anvisningar för hurkrav på märkning av artiklar ska anges påritning samt utföras på artiklar.
This standard comprises instructions on howpart markings are to be shown in technicaldrawings and how they are to be made on theparts themselves.
Materialmärkning på artiklar, se STD3871. Material marking on parts. See STD3871.Märkning av ledningsnät, se STD3222. Markings of cable harnesses. See STD3222.Märkning av prototypartiklar, se STD3636. Marking of prototype parts. See STD3636.Märkning av reservdelsförpackningar, seSTD4236en.
Marking of Spare Parts Packaging. SeeSTD4236en.
Motor och rammärkning för lastbilar ochbussar, se STD4243.
Engine and frame marking for trucks andbuses, see STD4243.
Ändringar f rån föregående utgåva Changes from previous issueTillhörande dokument ISO3779:2009 är tillagt.
Ändringen är skuggmarkerad.
Appurtenant document ISO 3779:2009 is
added.The change is shaded.
1 Tillämpning 1 GeneralAlla krav på märkning ska finnas angivet påritning.
All stipulated markings are to be shown ondrawing.
Allmänna anvisningar med rekommendationeroch exempel samt policy för identifierings-märkning av artiklar anges i STD14, somendast är avsedd för internt bruk.
General instructions, recommendations,examples and the policy of marking parts toenable their identification are given in STD14,a document which is for internal use only.
Här nedan anges de märkningsuppgifter sombehandlas i denna standard och som i olikaomfattning ska tillämpas för identifierings-märkning av artiklar.
Information is given below on the variousmarkings that are taken up in this standardand that are used for identification purposeson parts.
− Varumärke − Trademark − Artikelnummer − Part number − Datummärkning − Date marking −
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
2 Märkning för identifiering 2 Marking for identification purposes
2.1 Varumärke 2.1 TrademarkScanias symbol och logotyp är registreradevarumärken för Scania AB och därmedrättsligt skyddade och får endast användas avScania och leverantörer till Scania förmärkning av Scaniaartiklar, samt i fall vidsärskild överenskommelse.
The Scania symbol and logotype are theregistered trademarks of Scania AB. They areprotected by law and may only be used byScania and its suppliers for marking Scaniaparts, and in those instances where a specialagreement has been entered into.
Varumärke anges med symbol eller logotypeller symbol och logotyp i kombination.Märkning med dessa varumärken garanterarartiklarnas äkthet med sitt ursprung till Scania.
The trademark is the symbol or the logotype,or the symbol and the logotype incombination. Parts carry the Scaniatrademarks as a guarantee of theirauthenticity.
I de fall Scania måste acceptera leveran-törens eget varumärke och produkt-beteckning, ska detta vara tydligt skilt frånScanias märkning. I dessa fall fordras skriftligtgodkännande från Scania enligt intern rutin iSTD14.
In those instances when Scania is compelledto accept a supplier’s trademark and productdesignation on a part, then these should beclearly removed from Scania’s markings.Written approval is required from Scania insuch cases in accordance with the company’sinternal practice as stipulated in STD14.
2.2 Artikelnummer 2.2 Part numberArtikelnummer består av ett fem-, sex- ellersjusiffrigt löpnummer. Artikelnummer ärnödvändigt för identifiering av artiklar iproduktion samt i service- och reservdels-
sammanhang.
Part numbers consist of five, six or sevendigits. They enable identification when partsare being manufactured and are necessary forservicing and processing orders for spares.
Märkningsuppgiften kan innehålla annatartikelnummer än det som ritningen avser,t ex komplettnummer.
A drawing may sometimes give a part numberthat is different to the one intended as, forinstance, when the assembly number isquoted rather than that of the individual part.
2.3 Datummärkning 2.3 Date markingDatummärkning är en uppgift omtillverkningsdatum. Märkningen kan bestå av
en bokstavs-/sifferbeteckning som ger datum ikodad form. Datummärkning kan ocksåutföras med datumklocka eller datumfält.
The date marking states the day of manu-facture. It can consist of a designation made
up of letters or numbers that give the date inthe form of a code. The date marking can alsobe in the form of a date dial or date field.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
2.4 Leverantörsnummer 2.4 Supplier numberLeverantörsnummer består av en sifferkodsom identifierar leverantör. Leverantörs-nummer administreras av funktion Inköp somdelger leverantör. Det 4-siffriga leverantörs-numret från Matris-systemet används förmärkning.
The supplier number is a code consisting ofnumbers that identify the supplier. It isadministered by the Purchasing functionwhich is in contact with suppliers. The four-digit supplier number in the Matris system isused for marking.
2.5 Chargebeteckning 2.5 Charge designationChargebeteckning tillämpas för gjutna ochsmidda ämnen och lämnar uppgift om vilkensmälta ämnen har framställts ur. Krav påchargemärkning anges t ex i samband medatt artiklar ska härdas.
The charge designation is used for cast andforged materials and refers to the type ofcharge the materials were made from. Acharge designation is required if, for instance,a part is to be hardened.
2.6 Tilläggsmärkning 2.6 Supplementary marking
All annan märkning som ska finnas på enartikel utöver de uppgifter som beskrivits iavsnitten 2.1 - 2.5 är tillägg och ska anges iklartext på ritningen.
Any other markings on a part besides thosedescribed in sections 2.1 - 2.5 are classifiedas supplementary and are to be identifiedclearly on the drawing.
3 Markering för märkning på ritning 3 Indication of markings on drawing
3.1 Märkningssymbol 3.1 Marking symbolPlatsen för märkning markeras på ritning med
hjälp av en hörnstående kvadrat med 7 mmsida. Denna märkningssymbol finns även imärkningsrutan i huvudfältet.
The point where a marking is to be located on
the drawing is identified by a square standingupright on one corner and having 7 mm sides.The symbol is also shown in the marking boxon the title block.
Från ett av märkningssymbolens hörn dras enhänvisningslinje till den plats på artikeln därmärkningen ska utföras. Hänvisningslinjenavslutas med en pil eller punkt, beroende på ivilken vy märkningen anges, se figur 1 och 2.
A reference line leads from one of the cornersof the marking symbol to the point on the partwhere the marking is to be located. Thereference line ends with an arrow or dotdepending on the view at which the markingpoint is shown, see figures 1 and 2.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue.
Fig. 1 Fig. 2
3.2 Flera märkningar 3.2 Several markings are to be madeOm flera olika märkningar ska utföras, kanytterligare märkningsrutor anges i ritfältet medhjälp av ritningsetikett SV 1268-37.Märkningsrutorna skiljs genom positions-numrering i märkningssymbolen, se figur 3.
If several different markings are to be made,additional marking boxes can be placed in thedrawing space using drawing label SV 1268-37. The marking boxes are distinguished bynumbering the marking symbol, see figure 3.
3.3 The design and location of themarking and the direction in which itis read
Den märkningsmetod som tillämpas avgör ommärkningen utförs nedsänkt eller upphöjd imaterialet. All märkning ska utföras med vältäckande figurationer för symbol, bokstäveroch siffror, samt ge en jämn och tydligavbildning i underlaget. Ska märkningenutföras på ett visst sätt, anges detta påritningen. Är ytan för märkningen skymd,markeras detta med streckad linje.
The method of marking employed determineswhether the marking is to be impressed into orraised above the surface. All markings are tobe solid for symbols, letters and numbers andare to make a clear and even impression onthe material. Instructions regarding markingdone in a specific way should be stated on thedrawing. If the surface for marking is hidden, itis indicated with a dashed line.
Märkningsdjupet respektive den upphöjdareliefen är beroende av den märkningsmetodsom används och måste anpassas bl.a. efterartikelns godstjocklek och om artikeln skaytbeläggas, så att bästa möjliga tydlighet ochläsbarhet uppnås på färdigproducerad artikel.
The depth or height of the marking isdetermined by the method employed andshould take into account the thickness of thematerial and whether the part is to receivesurface treatment. This to ensure that clarityand legibility on the finished part are optimal.
När märkningen ska vara placerad på enbestämd plats på artikeln, anges mått till enruta, se exempel i figur 3.
When the marking is to be placed in a specificlocation on the part, the dimensions to asquare indicated, see example in figure 3.
Om märkningstexten ska vara läsbar från ettbestämt håll, anges en pil som markerartextens läsriktning, se figur 2 och 3.
If the marking text is to be read in a specificdirection, an arrow points the direction inwhich it is to be read, see figures 2 and 3.
Här följer några rekommendationer ommärkningens placering:
The following recommendations apply to thelocation of the marking:
− Märkningen ska placeras så att den inteblir estetiskt störande sedan artikeln
monterats.
− The marking should be placed in such away that it will not be an eyesore once the
part has been fitted.− Märkningen ska vara rättvänd och om
möjligt läsbar efter montering.− The marking should be the right way up
and, if possible, legible when fitted.− Märkningen ska om möjligt placeras
symmetriskt på artikeln.− The marking should, if possible, be
symmetrical to the part.− Ett ämnesnummer ska placeras så att det
avlägsnas i samband med bearbetning.− A blank number should be located in such
a way that it will come off during thecourse of machining.
− Reservdel som utgör komplett enhet ochbestår av flera ingående artiklar, ska pålämpligt sätt märkas medkomplettnummer.
− A spare part that is a complete unitconsisting of several constituent partsshould be marked with an assemblynumber in a suitable location.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue.
4 Angivelser i märkningsrutan 4 Indications in the marking boxI ritningens huvudfält finns en märkningsrutasom är avsedd för krav på märkning, se figur4.
The title block of the drawing contains amarking box in which the requirements formarking are given, see figure 4.
Hur denna märkningsruta ska fyllas i och huruppgifterna ska tolkas, framgår av avsnitten4.1 t o m 4.9.
As to how the marking box is to be filled inand the information contained thereininterpreted is described in sections 4.1 to 4.9.
4.1 Positionsnummer 4.1 Position numberPå denna plats i märkningssymbolen angesett positionsnummer i de fall flera märknings-rutor tillämpas.
The marking symbol contains a positionnumber if there is more than one marking boxand it is necessary to be able.
4.2 Antal rader 4.2 Number of linesOm märkningen ska fördelas på ett bestämtantal rader, ska denna uppgift anges här. Dåingen uppgift angivits, gäller anvisningar omfördelning enligt avsnitt 5.
If the marking is required to be divided up intoa definite number of lines, this informationshould be specified here. When noinformation is specified, the divisioninstructions in section 5 are applicable
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
4.3 Märkningsmetod 4.3 Marking methodPå denna plats i märkningsrutan anges enbokstavsbeteckning för krav på märknings-metod. Märkningsmetod anges med någon avde beteckningar som finns att välja bland itabellerna 1, 2 och 3.
A designation consisting of letters refers to therequirements for marking method. Themarking method adopted is shown using oneof the designations in table 1, 2 and 3.
BeteckningenMA1 i tabell 1 ochMA2 i tabell2 ger valfrihet vid tillverkning att välja lämpligmärkningsmetod inom respektive tabell.
The designations MA1 in table 1 andMA2 intable 2 denote that any method may beselected from the table in question for markinga part during its manufacture.
Möjlighet finns också att ange alternativamärkningsmetoder genom att angesnedstreck mellan beteckningarna, t exPUN/LAS.
An oblique stroke between two designationsas in PUN/LAS indicates that either of the twomethods may be used.
Finns inte önskad märkningsmetod med inågon av tabellerna 1, 2 eller 3, angesmetoden i klartext i anslutning till märknings-symbolen i ritfältet.
If the requisite marking method is not given inany of the tables 1, 2 or 3, then the methodadopted should be stated clearly next to themarking symbol in the drawing space.
En del märkningsmetoder kan i vissa fall gedeformationer i samband med märkning, vilketmåste beaktas när val görs.
Some marking methods may in certaininstances deform the part being made, afactor which should be taken intoconsideration when selecting a method.
I varje enskilt fall ska den märkningsmetodväljas som ger bästa möjliga resultat medavseende på tydlighet och varaktighet. Skaartikeln ytbeläggas, måste detta beaktas, så
att märkningen tydligt kvarstår efter belägg-ning.
A marking method should always be selectedthat gives the best possible results with regardto clarity and durability. If the part is to besurface coated, the marking should be clearly
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
Tabell 3 Märkningsmetoder för särskildaändamål
Table 3 Marking methods for specialpurposes
BeteckningDesignation
MärkningsmetodMarking method
MetodbeskrivningDescription of method
CAS
Gjutning ellerformsprutning.
Casting or injectionmoulding
Utförs genom nedsänkt eller upphöjd märkning i gjutform/-verktyget vid gjutning av metall och formsprutning av plast, dvs.upphöjd eller nedsänkt märkning på artikeln.
Performed by an impressed or raised marking in the castingmould/tool when casting metal or injection-moulding plastic, i.e.raised marking or impressed on the part.
CASR
Gjutning ellerformsprutning.
Casting or injectionmoulding
Utförs genom upphöjd märkning i gjutform/-verktyget vid gjutningav metall och formsprutning av plast, dvs. nedsänkt märkning påartikeln.
Performed by a raised marking in the casting mould/ tool whencasting metal or injection-moulding plastic, i.e. impressedmarking on the part.
CASI
Gjutning ellerformsprutning.
Casting or injectionmoulding
Utförs genom nedsänkt märkning i gjutform/-verktyget vidgjutning av metall och formsprutning av plast, dvs. upphöjdmärkning på artikeln.
Performed by a impressed marking in the casting mould/ toolwhen casting metal or injection-moulding plastic, i.e. raisedmarking on the part.
FORSmidning
Forging
Utförs genom verktyget vid smidning.
Performed with a tool when forging.
VUL
Vulkning
Vulcanization
Utförs med en varm stämpel som trycks mot materialet så att ettavtryck bildas, eller inlagt i formen vid vulkning.
Performed with a warm stamp which is pressed into the materialto form an impression, or insert in the moulding tool atvulcanization.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
Om beteckningen1A angivits tillåts val endastbland de två första i tabellen.
Designation1A means that a trademark maybe selected from the first two options only.
Varumärke som omfattar symbol och logotyp ikombination eller var för sig, ska återges medväl täckande figurationer i symbolen ochbokstäver i logotypen. Vid t ex stansning imaterial som inte medger användning avtäckande varumärke, ska varumärketkontureras. Lämplig tjocklek på konturlinjernaär ca 1/100 av hela bredden på logo-typen SCANIA.
In trademarks that consist of the symbol, thelogotype or both together, the symbol is to bereproduced in solid type and the logotype inletters. The trademark should be in outline ifthe material is to be punched and unsuitablefor reproducing the trademark in solid type. Asuitable thickness for the outline isapproximately 1/100 of the width of theSCANIA logotype in its entirety.
Reproduktion av symbol och logotyp får görasmed hjälp av det grafiska underlag som finnsåtergivet i tabell 5.
The symbol and logotype may be reproducedusing the graphical information in table 5.
För att få ett elektroniskt original av Scaniasvarumärke (symbol och logotyp) skaleverantörer först vända sig till sin SourcingManager på Scania inköp som skall godkännaatt leverantören får använda vår logotype ochsymbol för märkning av Scaniaartiklar. Dettagodkännande vidarebefordras i ett e-mail [email protected] medleverantörens e-mailadress, vilka original och ivilket filformat de önskas.Övriga avdelningar inom Scania skall kontaktaavd. KM:s helpdesk e-mail:[email protected].
To get an electronic original of Scaniatrademark (symbol and logotype) suppliersshall first contact their Sourcing Manager atScania purchasing department who shallapprove that the supplier may use ourlogotype and symbol for marking of Scaniaparts. This e-mail approval shall be forwardedto [email protected] with thesupplier email address, information about therequired originals and desired file format.Remaining departments inside Scania shouldcontact dep. KM’s helpdesk e-mail:[email protected].
Tidigare angivna beteckningar på äldreritningar för logotyp ersätts enligt nedan ochska gälla i samband med verktygsändring ochvid framtagning av nya verktyg.
Previous logotype designations on olddrawings have been changed as below. Theyapply when changes are made to tools andwhen new tools are developed.
Typ C (Standardlogotyp) ersätts avbeteckning1.
Type C (Standard logotype) is replaced bydesignation1.
Typ D (Speciallogotyp 1) ersätts avbeteckning1.
Type D (Special logotype 1) is replaced bydesignation1.
Typ E (Speciallogotyp 2) ersätts avbeteckning1.
Type E (Special logotype 2) is replaced bydesignation1.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
4.6 Art ikelnummer eller annanmärkningsuppgift
4.6 Part number or other markinginformation
På denna plats i märkningsrutan anges detartikelnummer, den text eller beteckning somartikeln ska märkas med.
This point in the marking box gives the partnumber, text or designation that the part is tobe marked with.
Om utrymmet inte räcker och en upplysningska lämnas, kan detta anges inom citattecken"….......", se exempel nedan.
If there is insufficient space and furtherinformation available then this can beindicated within quotation mark "….......", seeexamples below.
Här ges några exempel på angivelser ommärkning:
Below are several examples of indications formarkings:
− 1234567 (artikelnummer) − 1234567 (part number)− 1234567 LH (artikelnummer vänster) − 1234567 LH (part number left-hand)− INLET (text för anslutning) − INLET (text for a connection)− "See note" (märkningsuppgiften finns
angiven i en not)− "See note" (information regarding
marking is given in a note)− "Resp Part No." (märkning med respek-
tive artikelnummer)− "Resp Part No." (marking with the
respective part number)Siffror och märkningstexter ska utföras iteckensnitt Helvetica Regular (normal) ellerliknande inom teckenfamiljen Linjärer.
Numbers and marking texts are to be printedin Helvetica Regular (normal) or similar withinthe character family Grotesque.
4.7 Datummärkning 4.7 Date markingPå denna plats i märkningsrutan anges enbokstavsbeteckning då krav finns pådatummärkning. Angiven beteckningföreskriver den typ av datumangivelse somska tillämpas, se tabell 6.Märkning med exaktare tidsangivelse än somanges på ritning är tillåten, dvs TXM eller dattillåter även TXZ och TXW
This point in the marking box is for when datemarking is required. The designation is madeup of letters and refers to the type of datemarking to be applied, see table 6.Marking with a time indication more precisethan that stated on the drawing is allowed, i.e.TXM or dat allows TXZ and TXW
Beteckning för År och Månad finns att hämtafrån tabell 7 och 8.
Designation the various Year and Month arereproduced in tables 7 and 8.
Datummärkning på en artikel ska avse detdatum när artikeln tillverkas. Producerasartikeln i flera steg med viss tidsskillnad, skadatum vid sista steg gälla somtillverkningsdatum.
A date marking is the date of manufacture. Ifthe part is manufactured in several stages, itis the date of the final stage that is given asthe date of manufacture.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue. S T D 1 0 0 7 3 - 4
Tabell 7 Årsbeteckning Table 7 Designation of yearBeteckning enligt ISO 3779. Designation as per ISO 3779.
ÅrYear
BeteckningDesignation
ÅrYear
BeteckningDesignation
199619971998
19992000
TVW
XY
201120122013
20142015
BCD
EF20012002200320042005
12345
20162017201820192020
GHJKL
2006200720082009
2010
6789
A
2021202220232024
2025
MNPR
S
Tabell 8 Månadsbeteckning Table 8 Designation of month
MånadMonth
BeteckningDesignation
Januari / JanuaryFebruari/ February
Mars / March
ABC
April
Maj / MayJuni / June
D
EFJuli / July
Augusti / AugustSeptember
GHJ
Oktober / OctoberNovemberDecember
KLM
Då datummärkningen ska utföras meddatumklocka eller datumfält, vilket framgår avden bokstavsbeteckning som angivits, skautförandena vara i likhet med de som visas ifigurerna 5, 6 och 7.
If the date is to be marked in the form of adate dial or date field, as denoted by thealphabetical designation, it is to be done inaccordance with one of the examples infigures 5, 6 and 7.
Approved by/Assignor (department acronym, name) Standard responsible (department acronym, name)KM Stefan Lindblom UTDH Markku BackholmArea specialist (department acronym, name) Standard co-ordinator (department acronym, name)KMB Sverker Sundmark UTDH Iréne Klingberg
The electronic issue on the Scania Standards homepage on InLine is the valid original issue.
Tabell 9 Exempel på märkningsuppgifterpå en, två och tre rader(Datummärkning VE visar 1997Maj)
Table 9 Examples of markinginformation on one, two andthree lines(Date marking VE indicates 1997May)
1234567 VE 12341234567 VE 1234
1234567 VE 1234
VE 1234123456
En radOne line
Två rader Two lines
Tre rader Three lines
1234567 VE 1234
1234567 VE 1234
1234567 VE 1234
VE 1234123456
VE 1234123456
6 Utrymmesmått för märkning 6 Size of space for markingsUtrymme som en märkning upptar, bestäms
av teckenhöjden h, samt det antal uppgiftersom ska finnas med och det antal rader sommärkningen delas upp på. Tabell 10 gerungefärliga mått för det utrymme som behövs.
The amount of space that a marking takes up
is determined by the height of the charactersh, the amount of information it contains andthe number of lines on to which theinformation is to be divided into. Table 10presents in approximate figures the amount ofspace required.