INSTALLATION GUIDE STANDING SEAM
INSTALLATIONGUIDE
STANDING SEAM
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
1
Page 1 MetalMax Installation Book.xlsx
Pg. 2Pg. 2
Pg. 3Pg. 4Pg. 5Pg. 6Pg. 7
Pg. 8Pg. 9Pg. 10Pg. 11Pg. 12Pg. 13Pg. 14
SS Side Wall and End Wall ……………………………………………………..SS Step Ridge and Vented Ridge …………………………………………….
SS Panel and Trim Installation
Table Of Contents
SS Panel Information
SS Flashing Profiles
SS Pitch Change and Valley ……………………………………………………
SS Single Slope and Hip …………………………………………………………SS Plumb Eave and Flush Eave ……………………………………………….SS Box rake and Step Rake...…………………………………………………….
SS Valley, SS Pitch Change, Z-‐Bar, Cleat, and Offset Cleat……..….SS End Wall, Side Wall, Reglet and Counter Flashing…………...……SS Ridge and Hips………………………………....……..……………………..…..SS Rake's……..…..……………………….…………………..……………..………..
Field Hemming of Panel……………………………………………………...….
SS Eave's………………………..….…….………………....……………………..…..
SS 16 Panel Profile………………...…….………………………...…….………..SS 14 Panel Profile…………………………………………….…....……………..
Buy Direct from the Metal Man!
www.metalmax.com
2
Page 2 MetalMax Installation Book.xlsx
SS 14" Panel Profile
SS 16" Panel Profile
Blank:10.22"
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
3Page 3 MetalMax Installation Book.xlsx
SS Plumb Eave
Specify Pitch:
Specify Pitch:Blank: 8.18"
SS Square Rake
Blank: 8.5"
Blank: 8.5"
SS Flush Eave
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Buy Direct from the Metal Man!
www.metalmax.com
4
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page 4 MetalMax Installation Book.xlsx
SS Step Rake 16
Blank: 13.63"
SS Step Rake 14
Blank: 13.63"
SS Box Rake
Blank:10.22"
2-1/8”
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
5Page 5 MetalMax Installation Book.xlsx
SS Single Slope Ridge
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SS Step Ridge
SS Hip Gap
Buy Direct from the Metal Man!
www.metalmax.com
6Page 6 MetalMax Installation Book.xlsx
SS Counter Flashing
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SS Side Wall
SS End Wall
SS Reglet Flashing
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
7
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page 7 MetalMax Installation Book.xlsx
SS Valley
Blank: 20.44"
SS Pitch Change
*Specify Upper Pitch *Specify Low Pitch Blank: 13.63
SS 16 Z-‐Bar SS 14 Z-‐Bar SS Cleat SS Offset Cleat
8-3/4”
7/8”
Buy Direct from the Metal Man!
www.metalmax.com
8
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page 8 MetalMax Installation Book.xlsx
SS Box RakePop RivetSS Z-‐Bar1" Pancake Head ScrewButyl TapeSS Panel Bend up
SS Box Rake
Cleat
2) If panel rib will not be under box trim, you will need to bend up end 1".3) Attach cleat to fascia using a pancake head screw every 24" on center.
SS Step Rake1" 1/4" Painted Screw
Butyl Tape
Cleat
1" Pancake Head ScrewSS Step Rake
1) Attach cleat with pancake head screws every 24" on center.
2) If panel rib will not be under step rake trim, you will need to bend up end 1".
1) Measure where the z-‐bar needs to go on panel, apply butyl tape to bottom side of z-‐bar and screw down with pancake head screw every 12" on center.
4) Attach box rake trim by hooking it over the cleat first and then the z-‐bar and secure with pop rivet every 24" on center.
3) Apply butyl tape to the step down leg of trim, hook over cleat and screw down trim with a 1-‐1/2" woodscrew every 12" on center.
1” 1/2”
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
9Page 9 MetalMax Installation Book.xlsx
SS Plumb Eave
Panel
Plumb Eave
Underlayment
1) Attach eave trim with pancake head screw 24" on center.
2) Hem panel and attach panel to eave trim.
SS Flush Eave
Panel
1" Pancake Head Screw
Offset Cleat
Butyl Tape
Flush Eave
1" Pancake Head Screw
Cleat
2) Attach trim over the cleat.
1) Attach cleat to fascia with pancake head screw 24" on center. Mak sure that the cleat will set in the open hem of trim.
3) Apply butyl tape to the bottom side of the 1-‐1/2" leg of the offset cleat . Attach the offset cleat on top of the eave trim with pancake head screw. Hem panel and attach to the offset cleat.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Buy Direct from the Metal Man!
www.metalmax.com
10
Page 10 MetalMax Installation Book.xlsx
SS Single Slope Ridge
Pop Rivet SS Single Slope RidgeZ-‐BarButyl Tape1" Pancake
head screw Cleat
SS Hip Pop Rivet SS Hip Pop Rivet
Z-‐Bar 1" Pancakehead screw
1) Marke panels off for z-‐bar.
3) Hook hip trim on z-‐bar and secure with pop rivets.
1) Marke panels off for z-‐bar. Apply butyl tape to bottom side of Z-‐Bar. Attach Z-‐Bar to panel with 1" pancake head screw and seal edges of Z-‐Bar were they meet panel ribs.
2) Attach cleat to fascia side with 1" pancake head screw. Hook Single slope ridge trim over cleat and Z-‐Bar. Secure trim to Z-‐Bar with pop rivet.
2) Cut z-‐bar the width of the panel, Apply butyl tape to bottom side of z-‐bar and attach z-‐bar to panels. Apply sealer on both ends where z-‐bar meets panel ribs.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
11
Page 11 MetalMax Installation Book.xlsx
2) Apply sealer to both sides of z-‐bar where the trim meets the panel ribs.
Pop Rivet Step Ridge Cap
Vented Closure Closure Clip
1) Mark your panels for ridge cap placement.
2)Apply vented closure strip to panels and secure with closure clips and 2 each screws.3)Hook ridge cap over clips and secure with a pop rivet.
SS Step Ridge
Z-‐Bar Pancake Head Screw SS Ridge Cap Butyl tape Sealer(Edge's of z-‐bar) Pop Rivet
1) Cut z-‐bar to fit inside of panel, apply butyl tap to bottom side of z-‐bar and attach to roof with pancake head screw.
3) Attach Step ridge by hooking both sides of opem hem to z-‐bar and secureing with pop rivets every 24" on center.
SS Vented Step Ridge
1" Pancake head screw
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Buy Direct from the Metal Man!
www.metalmax.com
12
Page 12 MetalMax Installation Book.xlsx
Sealer
Reglet Trim SS End wall Panel End Pop Rivet Z-‐Bar 1" Pancakehead screw.
Butyl tape
1) Bend edge of panel up about 1". Measure over for Z-‐Bar placement.2)Apply butyl tape to bottom side of Z-‐Bar and attch with 1" pancakehead screw.
3)Hook side wall trim over z-‐bar and secure with pop rivet. Attach upper side to wall with a fastener.4) For brick, cut 1/8" grove in wall and install reglet trim. Run a bead of sealer at top edge of trim.
SS End Wall Counter Flashing
Sealer OR Reglet Trim
SS End Wall
Pop rivetZ-‐Bar
Butyl Tape1" Pancake head screw
1) Measure over for Z-‐Bar placement.2)Apply butyl tape to bottom side of Z-‐Bar and attch with 1" pancakehead screw.
3)Hook end wall trim over z-‐bar and secure with pop rivet. Attach upper side to wall with a fastener.
4) For brick, cut 1/8" grove in wall and install reglet trim. Run a bead of sealer at top edge of trim.
SS Side Wall
5) For siding, remove bottom J-‐Channel and attach upper side of trim to wall. Re-‐Install J-‐ Channel and siding.
5) For siding, remove bottom J-‐Channel and attach upper side of trim to wall. Re-‐Install J-‐ Channel and siding.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Don’t Buy from the Middle Man. . .
STANDING SEAM Installation Guide
13Page 13 MetalMax Installation Book.xlsx
SS Pitch Change Pop rivet
Offset Cleat
Butyl Tape 1"Pancakehead Screw Z-‐Bar
1) Install Lower panel first.
3) Attach pitch change trim by hooking over Z-‐Bar and securing with a pop rivet.
SS ValleyOffset Cleat Valley Offset Cleat
1" Pancakehead Screw Butyl Tape
1) Attach valley with 1" pancake head screw at outside edges.
3) Apply hem to panel and hook over offset cleat.
4) Apply butyl tape to bottom side of offset cleat and attach to upper side of pitch change with a 1" pancake head screw. Hem panel and hook over offset cleat.
SS Pitch Change
2) Apply butyl tape to bottom side of Z-‐Bar and attach to lower panels. Apply sealer to both sides of z-‐bar where the trim meets the panel ribs.
2) Apply butyl tape to bottom side of offset cleat and attach offset cleat to valley about 5" from center of valley with 1" pancake head screw.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Buy Direct from the Metal Man!
www.metalmax.com
14Page 14 MetalMax Installation Book.xlsx
WWW.METALMAX.COM