Standards and Guidelines for Internal Combustion Engines German Standards Standard Title Date of publication DIN 1940 Verbrennungsmotoren; Hubkolbenmotoren, Begriffe, Formelzeichen, Einheiten (Reciprocating internal combustion engines; terms, formulae, units) 1976-12 DIN 6261 Verbrennungsmotoren; Teile fu ¨r Kreiskolbenmotoren, A ¨ ußerer Aufbau, Triebwerk, Begriffe (Internal combustion engines; components of rotating piston engines, setup of engine, driving mechanism, definitions) 1976-02 DIN 6262 Verbrennungsmotoren; Arten der Aufladung, Begriffe (Internal combustion engines; methods of pressure-charging, definitions) 1976-06 DIN 6267 Verbrennungsmotoren; Arten der ¨ Olschmierung, Begriffe (Methods of lubrication for internal combustion engines) 1971-01 DIN 6271-3 Hubkolben-Verbrennungsmotoren; Anforderungen; Leistungstoleranzen; Erga ¨nzende Festlegungen zu DIN ISO 3046 Teil 1 (Reciprocating internal combustion engines; performance; power tolerances; supplementary stipulations to DIN ISO 3046 Part 1) 1991-04 DIN 6274 Verbrennungsmotoren fu ¨r allgemeine Verwendung; Druckluftbeha ¨lter mit Ventilkopf; 38 mm Durchgang; Zusammenstellung (Internal combustion engines for general purposes; Compressed air containers with valve block; 38 mm bore; Assembly) 1982-04 DIN 6275 Verbrennungsmotoren fu ¨r allgemeine Verwendung; Druckluftbeha ¨lter fu ¨r zula ¨ssigen Betriebsu ¨berdruck bis 30 bar (Internal combustion engines for general purposes; Compressed air containers for permissible working overpressures up to 30 bar) 1982-04 DIN 6276 Verbrennungsmotoren fu ¨r allgemeine Verwendung; Ventilk¨ opfe fu ¨r Druckluftbeha ¨lter; 38 mm Durchgang (Internal combustion engines for general purposes; Valve blocks for compressed air containers; 38 mm bore) 1982-04 K. Mollenhauer, H. Tschoeke (eds.), Handbook of Diesel Engines, DOI 10.1007/978-3-540-89083-6, Ó Springer-Verlag Berlin Heidelberg 2010 609
28
Embed
Standards and Guidelines for Internal Combustion Engines978-3-540-89083-6/1.pdf · Standards and Guidelines for Internal Combustion Engines ... Standards and Guidelines for Internal
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Standards and Guidelines for Internal Combustion Engines
DIN 6261 Verbrennungsmotoren; Teile fur Kreiskolbenmotoren, AußererAufbau, Triebwerk, Begriffe (Internal combustion engines; componentsof rotating piston engines, setup of engine, driving mechanism,definitions)
1976-02
DIN 6262 Verbrennungsmotoren; Arten der Aufladung, Begriffe (Internalcombustion engines; methods of pressure-charging, definitions)
1976-06
DIN 6267 Verbrennungsmotoren; Arten der Olschmierung, Begriffe (Methods oflubrication for internal combustion engines)
1971-01
DIN 6271-3 Hubkolben-Verbrennungsmotoren; Anforderungen;Leistungstoleranzen; Erganzende Festlegungen zu DIN ISO 3046 Teil 1(Reciprocating internal combustion engines; performance; powertolerances; supplementary stipulations to DIN ISO 3046 Part 1)
1991-04
DIN 6274 Verbrennungsmotoren fur allgemeine Verwendung; Druckluftbehaltermit Ventilkopf; 38 mm Durchgang; Zusammenstellung (Internalcombustion engines for general purposes; Compressed air containerswith valve block; 38 mm bore; Assembly)
1982-04
DIN 6275 Verbrennungsmotoren fur allgemeine Verwendung; Druckluftbehalterfur zulassigen Betriebsuberdruck bis 30 bar (Internal combustionengines for general purposes; Compressed air containers for permissibleworking overpressures up to 30 bar)
1982-04
DIN 6276 Verbrennungsmotoren fur allgemeine Verwendung; Ventilkopfe furDruckluftbehalter; 38 mm Durchgang (Internal combustion engines forgeneral purposes; Valve blocks for compressed air containers; 38 mmbore)
1982-04
K. Mollenhauer, H. Tschoeke (eds.), Handbook of Diesel Engines, DOI 10.1007/978-3-540-89083-6,� Springer-Verlag Berlin Heidelberg 2010
609
Standard Title Date of publication
DIN 6280-10 Hubkolben-Verbrennungsmotoren; Stromerzeugungsaggregate mitHubkolben-Verbrennungsmotoren; Stromerzeugungsaggregate kleinerLeistung; Anforderungen und Prufung (Reciprocating internalcombustion engines; generating sets with reciprocating internalcombustion engines; small power generating sets; requirements andtests)
1986-10
DIN 6280-12 Stromerzeugungsaggregate – Unterbrechungsfreie Stromversorgung –Teil 12: Dynamische USV-Anlagen mit und ohne Hubkolben-Verbrennungsmotor (Generating sets – Uninterruptible power supply –Part 12: Dynamic UPS systems with and without reciprocating internalcombustion engines)
1996-06
DIN 6280-13 Stromerzeugungsaggregate – Stromerzeugungsaggregate mitHubkolben-Verbrennungsmotoren – Teil 13: FurSicherheitsstromversorgung in Krankenhausern und in baulichenAnlagen fur Menschenansammlungen (Generating sets – Reciprocatinginternal combustion engines driven generating sets – Part 13: Foremergency power supply in hospitals and public buildings)
1994-12
DIN 6280-14 Stromerzeugungsaggregate – Stromerzeugungsaggregate mitHubkolben-Verbrennungsmotoren – Teil 14: Blockheizkraftwerke(BHKW) mit Hubkolben-Verbrennungsmotoren; Grundlagen,Anforderungen, Komponenten, Ausfuhrung und Wartung (Generatingsets – Reciprocating internal combustion engines driven generating sets– Part 14: Combined heat and power system (CHPS) with reciprocatinginternal combustion engines; basics, requirements, components andapplication)
1997-08
DIN 6280-15 Stromerzeugungsaggregate – Stromerzeugungsaggregate mitHubkolben-Verbrennungsmotor – Teil 15: Blockheizkraftwerke(BHKW) mit Hubkolben-Verbrennungsmotoren; Prufungen(Generating sets – Reciprocating internal combustion engines drivengenerating sets – Part 15: Combined heat and power system (CHPS)with reciprocating internal combustion engines; tests)
1997-08
DIN 6281 Stromerzeugungsaggregate mit Kolbenkraftmaschinen;Anschlussmaße fur Generatoren und Kolbenkraftmaschinen(Generator sets with reciprocating internal combustion engines;Connection dimensions for generators and reciprocating internalcombustion engines)
1978-04
DIN 6288 Hubkolben-Verbrennungsmotoren – Anschlussmaße undAnforderungen fur Schwungrader und elastische Kupplungen(Reciprocating internal combustion engines – Dimensions andrequirements for flywheels and flexible couplings)
2000-07
DIN 24189 Prufung von Luftfiltern fur Verbrennungskraftmaschinen undKompressoren; Prufverfahren (Testing of air cleaners for internalcombustion engines and compressors; test methods)
1986-01
610 Standards and Guidelines for Internal Combustion Engines
ISO TC 22 Road Vehicles
Standard Title Date of publication
ISO 7648 Flywheel housings for reciprocating internal combustion engines;Nominal dimensions and tolerances
1987-07
ISO TC 70 Internal Combustion Engines
Standard Title Date of publication
ISO 1204 Reciprocating internal combustion engines; designation of thedirection of rotation and of cylinders and valves in cylinder heads,and definition of right-hand and left-hand in-line engines andlocations on an engine
1990-12
ISO 2261 Reciprocating internal combustion engines – Hand-operatedcontrol devices – Standard direction of motion
1994-12
ISO 2710-1 Reciprocating internal combustion engines – Vocabulary – Part 1:Terms for engine design and operation
2000-09
ISO 2710-2 Reciprocating internal combustion engines – Vocabulary – Part 2:Terms for engine maintenance
1999-12
ISO 3046-1 Reciprocating internal combustion engines – Performance – Part 1:Declarations of power, fuel and lubricating oil consumptions, andtest methods; Additional requirements for engines for general use
2002-05
ISO 3046-3 Reciprocating internal combustion engines; performance; Part 3:Test measurements
1989-11
ISO 3046-4 Reciprocating internal combustion engines – Part 4: Speedgoverning
1997-03
ISO 3046-5 Reciprocating internal combustion engines – Performance – Part 5:Torsional vibrations
2001-12
ISO 3046-6 Reciprocating internal combustion engines; performance; Part 6:Overspeed protection
1990-10
ISO 6798 Reciprocating internal combustion engines – Measurement ofemitted airborne noise – Engineering method and survey method
1995-12
ISO 6826 Reciprocating internal combustion engines – Fire protection 1997-02
ISO 7967-1 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 1: Structure and external covers
2005-06
ISO Standards
Standards and Guidelines for Internal Combustion Engines 611
Standard Title Date of publication
ISO 7967-2 Reciprocating internal combustion engines; Vocabulary ofcomponents and systems; Part 2: Main running gear Trilingualedition
1987-11
ISO 7967-2/AMD
Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 2: Main running gear; Amendment 1
1999-12
ISO 7967-3 Reciprocating internal combustion engines; Vocabulary ofcomponents and systems; Part 3: Valves, camshaft drive andactuating mechanisms Trilingual edition
1987-11
ISO 7967-4 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 4: Pressure charging and air/exhaust gas ducting systems
2005-06
ISO 7967-5 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 5: Cooling systems
2003-02
ISO 7967-6 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 6: Lubricating systems
2005-06
ISO 7967-7 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 7: Governing systems
2005-06
ISO 7967-8 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 8: Starting systems
2005-06
ISO 7967-9 Reciprocating internal combustion engines – Vocabulary ofcomponents and systems – Part 9: Control and monitoring systems
1996-11
ISO 8528-1 Reciprocating internal combustion engine driven alternating currentgenerating sets – Part 1: Application, ratings and performance
2005-06
ISO 8528-2 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 2: Engines
2005-06
ISO 8528-3 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 3: alternating current generators forgenerating sets
2005-06
ISO 8528-4 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 4: Controlgear and switchgear
2005-06
ISO 8528-5 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 5: Generating sets
2005-06
ISO 8528-6 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 6: Test methods
2005-06
612 Standards and Guidelines for Internal Combustion Engines
Standard Title Date of publication
ISO 8528-7 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 7: Technical declarations forspecification and design
1994-11
ISO 8528-8 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 8: Requirements and tests for low-power generating sets
1995-12
ISO 8528-9 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 9: Measurement and evaluation ofmechanical vibration
1995-12
ISO 8528-10 Reciprocating internal combustion engine driven alternatingcurrent generating sets – Part 10: Measurement of airborne noiseby the enveloping surface method
1998-10
ISO 8528-12 Reciprocating internal combustion engine driven alternating currentgenerating sets – Part 12: Emergency power supply to safety services
1997-09
ISO 8861 Shipbuilding – Engine-room ventilation in diesel-engined ships –Design requirements and basis of calculations
1998-05
ISO 8665 Small craft – Marine propulsion engines and systems – Powermeasurements and declarations
1994-08
ISO 8999 Reciprocating internal combustion engines – Graphical symbols 2001-03
ISO 10054 Internal combustion compression-ignition engines – Measurementapparatus for smoke from engines operating under steady-stateconditions – Filter-type smokemeter
1998-09
ISO 11102-1 Reciprocating internal combustion engines – Handle startingequipment – Part 1: Safety requirements and tests
1997-10
ISO 11102-2 Reciprocating internal combustion engines – Handle startingequipment – Part 2: Method of testing the angle of disengagement
1997-10
ISO 13332 Reciprocating internal combustion engines – Test code for themeasurement of structure-borne noise emitted from high-speedand medium-speed reciprocating internal combustion enginesmeasured at the engine feet
2000-11
ISO 14314 Reciprocal internal combustion engines – Recoil startingequipment – General safety requirements
2004-03
ISO 14396 Reciprocating internal combustion engines – Determination andmethod for the measurement of engine power – Additionalrequirements for exhaust emission tests in accordance withISO 8178
2002-06
Standards and Guidelines for Internal Combustion Engines 613
Standard Title Date of publication
ISO 15550 Internal combustion engines – Determination and method for themeasurement of engine power – General requirements
ISO TC 70/SC 7 Internal combustion engines – Tests for lubricating oil filters
Standard Title Date of publication
ISO 4548-1 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 1: Differential pressure/flow characteristics
1997-09
ISO 4548-2 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 2: Element by-pass valve characteristics
1997-09
ISO 4548-3 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 3: Resistance to high differentialpressure and to elevated temperature
1997-09
ISO 4548-4 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 4: Initial particle retention efficiency,life and cumulative efficiency (gravimetric method)
1997-12
ISO 4548-5 Methods of test for full-flow lubricating oil filters for internalcombustion engines; Part 5: Cold start simulation and hydraulicpulse durability test
1990-12
ISO 4548-6 Methods of test for full-flow lubricating oil filters for internalcombustion engines; Part 6 : Static burst pressure test
1985-12
ISO 4548-7 Methods of test for full-flow lubricating oil filters for internalcombustion engines; Part 7: Vibration fatigue test
1990-11
ISO 4548-9 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 9: Inlet and outlet anti-drain valve tests
1995-07
ISO 4548-11 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 11: Self-cleaning filters
1997-09
ISO 4548-12 Methods of test for full-flow lubricating oil filters for internalcombustion engines – Part 12: Filtration efficiency using particlecounting, and contaminant retention capacity
ISO 8178-1 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 1: Test-bed measurement of gaseous andparticulate exhaust emissions
2006-09
614 Standards and Guidelines for Internal Combustion Engines
Standard Title Date of publication
ISO 8178-2 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 2: Measurement of gaseous and particulateexhaust emissions under field conditions
2008-04
ISO 8178-3 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 3: Definitions and methods of measurement ofexhaust gas smoke under steady-state conditions
1994-09
ISO 8178-4 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 4: Steady-state test cycles for different engineapplications
2007-12
ISO 8178-5 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 5: Test fuels
2008-10
ISO 8178-6 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 6: Report of measuring results and test
2000-11
ISO 8178-7 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 7: Engine family determination
1996-11
ISO 8178-8 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 8: Engine group determination
1996-11
ISO 8178-9Amd 1
Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 9: Test cycles and test procedures for test bedmeasurement of exhaust gas smoke emissions from compressionignition engines operating under transient conditions
2004-10
ISO 8178-10 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 10: Test cycles and test procedures for fieldmeasurement of exhaust gas smoke emissions from compressionignition engines operating under transient conditions
2002-11
ISO 8178-11 Reciprocating internal combustion engines – Exhaust emissionmeasurement – Part 11: Test-bed measurement of gaseous andparticulate exhaust emissions from engines used in nonroad mobilemachinery under transient test conditions
2006-04
Standards and Guidelines for Internal Combustion Engines 615
European Standards (CEN/TC 270)
Standard Title Date of publication
EN 1679-1 Reciprocating internal combustion engines. Safety. Part 1:Compression ignition engines
1997
EN 1834-1 Reciprocating internal combustion engines. Safetyrequirements for design and construction of engines foruse in potentially explosive atmospheres. Part 1: Group IIengines for use in flammable gas and vapor atmospheres
2000-01
EN 1834-2 Reciprocating internal combustion engines. Safetyrequirements for design and construction of engines foruse in potentially explosive atmospheres. Part 2: Group Iengines for use in underground workings susceptible forfiredamp and/or combustible dust
2000-01
EN 1834-3 Reciprocating internal combustion engines. Safetyrequirements for design and construction of engines foruse in potentially explosive atmospheres. Part 3: Group IIengines for use in flammable dust atmospheres
2000-01
EN 10090 Valve steels and alloys for internal combustion engines 1998-02
EN 12601 Reciprocating internal combustion engine drivengenerating sets. Safety
2001-02
CIMAC Recommendations
Number Title Year
No 2 Recommendations for gas turbine acceptance test 1968
No 3 Recommendations of measurement for the overall noiseof reciprocating engines
1970
No 4 Recommendations for SI units for diesel engines and gasturbines
1975
No 5 Recommendations for supercharged diesel engines. PartI: Engine de-rating on account of ambient conditions;Part II: Engine acceptance tests
1971
No 6 Lexicon on combustion engines – Technical terms of theIC engine and gas turbine industries
1977
No 7 Recommendations regarding liability – Assuredproperties, publications, fuels for diesel engines
1985
No 10 Recommendations regarding liability – Assuredproperties, publications, fuels for gas turbines
1988
616 Standards and Guidelines for Internal Combustion Engines
Number Title Year
No 11 Recommendations regarding fuel requirements for dieselengines. Updated version of No 8
1990
No 12 Exhaust emissions measurement recommendations forreciprocating engines and gas turbines
1991
No 14 Standard method for the determination of structurebornenoise from engines
1994
No 15 Guidelines for the lubrication of two-stroke crossheaddiesel engines
1997
No 16 Guidelines for operation and/or maintenance contracts 1999
No 17 Guidelines for diesel engines lubrication – Oilconsumption of medium speed diesel engines
1999
No 18 Guidelines for diesel engines lubrication – Impact of fuelon lubrication
2000
No 19 Recommendations for the lubrication of gas engines 2000
No 20 Guidelines for diesel engines lubrication – Lubrication oflarge high speed diesel engines
2002
No 21 Recommendations regarding fuel quality for diesel engines 2003
No 22 Guidelines for diesel engines lubrication – Oil degradation 2004
No 23 Standards and methods for sampling and analyzing emissioncomponents in non-automotive diesel and gas engineexhaust gases – Marine and land based power plant sources
2005
No 24 Treatment of the system oil in medium speed andcrosshead diesel engine installations
2005
No 25 Recommendations concerning the design of heavy fueltreatment plants for diesel engines. Updated version of No 9
2006
No 26 Guidelines for diesel engine lubrication – Impact of lowsculpture fuel on lubrication of marine engines
2007
No 27 Turbo charging efficiencies – Definitions and guidelinesfor measurement and calculation
2007
No 28 Guide to diesel exhaust emissions control of NOx, SOx,particulates, smoke and CO2 – Seagoing ships and largestationary diesel power plants
2008
No 29 Guidelines for the lubrication of medium speed dieselengines. Updated version of No 13
2008
Standards and Guidelines for Internal Combustion Engines 617
Motor Vehicle Council – Powertrain Systems Group
Number Title Publication date
J604 Engine terminology and nomenclature – General Jun 1995
J824 Engine rotation and cylinder numbering Jun 1995
J922 Turbocharger nomenclature and terminology Jun 1995
J1004 Glossary of engine cooling system terms Aug 2004
J1515 Impact of alternative fuels on engine test and reporting procedures Jun 1995
Diesel fuel injection equipment
HS3458 SAE Fuel injection systems and testing methods standards manual(34 documents)