ROBEX 200W-7 Standard Equipment ISO standard cab All-weather steel cab with all-around visibility Safety glass windows Rise-up type windshield wiper Sliding fold-in front window Sliding side window Lockable door Hot & cool box Accessory box & Ash-tray Computer Aided Power Optimization (New CAPO) system 2-power mode, 3-work mode, 2-user mode Auto deceleration & one touch deceleration system Auto warm up system Auto overheat prevention system Heater(7,500 kcal/hr, 30,000BTU/hr) & Defroster Self diagnostic system Centralized monitoring LCD display Engine speed Clock & Error code Gauges Fuel level gauge Engine coolant temperature gauge Hyd. oil temperature gauge Warning Fuel level Check Engine & CPU Engine oil pressure Engine coolant temperature Hyd. oil temperature Low battery Air cleaner clogging Indicator Power max. Preheat & Engine warming-up One touch decel Removable clean out screen for oil cooler Door and cab locks, one key Two outside rearview mirrors Fully adjustable suspension seat with seat belt Slidable joystick, pilot-operated Automatic swing brake Removable reservoir tank Water separator & Fuel pre-filter, fuel line Boom holding system Arm holding system Counterweight (3,400 kg, 7,500 lb) mono boom (5.65 m, 18’ 6”) Arm (2.9 m, 9’ 6”) Radio & USB player Remote control switch Console box tilting system (LH.) Three front working light Electric horn Batteries (2 x 12V x 100 AH) Battery master switch Starting Aid(air grid heater) cold weather Standard bucket(0.80 m 3 , 1.05 yd 3 ) Rear dozer and front outrigger Rear - blade (610 mm x 2490 mm) Tires - dual (10.00 - 20 - 16PR) Travel alarm Fuel warmer Cabin roof cover-steel Optional Equipment Independent operating - 4 outrigger Air-conditioner (5,000kcal/hr, 20,000BTU/hr) FATC (Full Automatic Temperature Control) Heater & Defroster Sun visor for cabin inside Fuel filler pump (35 /min, 9.5 US gpm) Beacon lamp Safety lock valve for boom cylinder with overload warning device Safety lock valve for arm cylinder Single acting piping kit (breaker, etc) Double acting piping kit (clamshell, etc) 12 volt power supply (DC-DC converter) Electric. transducer Quick coupler Various optional Arms Super short arm (2.0 m, 6’ 7”) Short arm (2.4 m, 7’ 10”) Various optional Buckets (SAE heaped) Narrow bucket (0.51 m 3 , 0.67 yd 3 ) Light duty bucket (0.87 m 3 , 1.14 yd 3 ) Light duty bucket (0.92 m 3 , 1.20 yd 3 ) Light duty bucket (1.10 m 3 , 1.44 yd 3 ) Light duty bucket (1.20 m 3 , 1.57 yd 3 ) Light duty bucket (1.34 m 3 , 1.75 yd 3 ) Heavy duty bucket (0.74 m 3 , 0.97 yd 3 ) Heavy duty bucket (0.90 m 3 , 1.18 yd 3 ) Heavy duty bucket (1.05 m 3 , 1.37 yd 3 ) Rock-Heavy duty bucket (0.87 m 3 , 1.14 yd 3 ) Slope finishing bucket (0.75 m 3 , 0.98 yd 3 ) Cabin lights Cabin FOPS/FOG (ISO/DIS 10262) FOPS (Falling Object Protective Structure) FOG (Falling Object Guard) Cabin Rwf-cover Transparent Tool kit Operator suit Special cowling Air vent type side door Engine emergency control Undercarriage Rear and front outrigger Tiers - dual (10.00 - 20 solid) Seat Adjustable air suspension seat Mechanical Suspension seat with heater Adjustable air suspension seat with heater Low noise kit Ring fan Special F/G hood Pattern changer (2pattern) PLEASE CONTACT www.hyundai-ce.com 2010.07 Rev.10 *Photo may include optional equipment. WHEELED EXCAVATOR Applied Tier 2 Engine 200W-7 * Standard and optional equipment may vary. Contact your Hyundai dealer for more information. The machine may vary according to International standards. * The photos may include attachments and optional equipment that are not available in your area. * Materials and specifications are subject to change without advance notice. * All imperial measurements rounded off to the nearest pound or inch.
9
Embed
Standard Equipment Optional Equipment - Porter Group Hyundai models... · Standard Equipment ISO standard cab All ... Single acting piping kit (breaker, ... Hyundai engineering helps
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ROBEX 200W-7
Standard EquipmentISO standard cab
All-weather steel cab with all-around visibilitySafety glass windowsRise-up type windshield wiperSliding fold-in front windowSliding side windowLockable doorHot & cool boxAccessory box & Ash-tray
Computer Aided Power Optimization(New CAPO) system
2-power mode, 3-work mode, 2-user modeAuto deceleration & one touch deceleration systemAuto warm up systemAuto overheat prevention system
Removable clean out screen for oil coolerDoor and cab locks, one keyTwo outside rearview mirrorsFully adjustable suspension seat with seat beltSlidable joystick, pilot-operatedAutomatic swing brakeRemovable reservoir tankWater separator & Fuel pre-filter, fuel lineBoom holding systemArm holding systemCounterweight (3,400 kg, 7,500 lb)mono boom (5.65 m, 18’ 6”)Arm (2.9 m, 9’ 6”)Radio & USB player
Remote control switchConsole box tilting system (LH.)Three front working lightElectric hornBatteries (2 x 12V x 100 AH)Battery master switchStarting Aid(air grid heater) cold weatherStandard bucket(0.80 m3, 1.05 yd3)Rear dozer and front outriggerRear - blade (610 mm x 2490 mm)Tires - dual (10.00 - 20 - 16PR)Travel alarmFuel warmerCabin roof cover-steel
Optional EquipmentIndependent operating - 4 outriggerAir-conditioner (5,000kcal/hr, 20,000BTU/hr)FATC (Full Automatic Temperature Control)Heater & DefrosterSun visor for cabin insideFuel filler pump (35 /min, 9.5 US gpm) Beacon lampSafety lock valve for boom cylinder with
overload warning deviceSafety lock valve for arm cylinderSingle acting piping kit (breaker, etc)Double acting piping kit (clamshell, etc)12 volt power supply (DC-DC converter)Electric. transducerQuick coupler
Various optional ArmsSuper short arm (2.0 m, 6’ 7”)Short arm (2.4 m, 7’ 10”)
Air vent type side doorEngine emergency controlUndercarriage
Rear and front outriggerTiers - dual (10.00 - 20 solid)Seat
Adjustable air suspension seatMechanical Suspension seat with heaterAdjustable air suspension seat with heater
Low noise kitRing fanSpecial F/G hood
Pattern changer (2pattern)
PLEASE CONTACT
www.hyundai-ce.com 2010.07 Rev.10
*Photo may include optional equipment.
WHEELED EXCAVATOR Applied Tier 2 Engine
200W-7
* Standard and optional equipment may vary.Contact your Hyundai dealer for more information.The machine may vary according to Internationalstandards.
* The photos may include attachments and optionalequipment that are not available in your area.
* Materials and specifications are subject tochange without advance notice.
* All imperial measurements rounded off to thenearest pound or inch.
HYUNDAI 7 Series Wheeled Excavator HYUNDAI 7 Series Wheeled Excavator The ROBEX 200W-7 provides outstanding performance,working harder and faster in a variety of job conditions.Hyundai’s ROBEX 7 series features a comfortableoperator environment with advanced ergonomics.
Wide Cab with Excellent Visibility The cab is roomy and ergonomically designed with low noise level and good visibility. A full view front window and large rear and side windows provide excellent visibility in all directions.
Highly Sensitive Joystick and Easy Entrance New joystick grips for precise control have been equipped with double switches.
Dial Type Engine Speed Switch and Key Switch Front Switch Panel
Raise-up wiper has enhanced for the better front view. Cabin Lights enhance safety by brightly lightingthe surroundings during night work(optional)
Convenient Acceleration and Brake Pedal
AA
B
C
D
E
F
G
B C
E F G
D
2 3*Photo may include optional equipment.
Excellent VentilationVentilation has been improved by the addition of the larger fresh air intake system, and by providing additional air flow throughout the cab.Sliding front and side windows provide improved ventilation.A large sunroof offers upward visibility and additional ventilation.
VisibilityEven more visibility than before, for safer, more efficient operating.
Comfortable Operator EnvironmentThe control levers and seat can be adjusted to provide maximum operator comfort. The seat is fully adjustable for optimum operating position, reducingoperator fatigue. Console boxes slide forward and backward for improved accessibility. The proportional pressure controls reduce unnecessary exertionwhile ensuring precise operation.
Large windows allow excellent visibility in all directions.
Low noise designThe Robex 7 series was designed with low operation noise in mind.Hyundai engineering helps to keep interior and exterior noise levels toa minimum. The cab's noise levels have been additionally reduced by improvingthe door seals for the cab and engine compartments. An insulated diesel engine compartment with sound-damping materialalso reduces noise.
Easy-to-Reach Control PanelsSwitches and other essential controlsare located near the operator. Thesehelp keep operator movement to aminimum, enhancing control with lessoperator fatigue.
Power boostOne touch decelerationHornOptional
Left
Right
Rear Emergency Exit WindowRear exit window is designed witheasy exit for operator's safety.
Improved Intelligent DisplayInstrument panel is installed in frontof RH console box. It is easy to check all critical systemswith easy-to-read indicators.
Operating Environment
3
Switch panel(R.H)Horn buttonOption button(breaker operation)Remote radio controlClusterHour meterAccel pedalBrake pedalMulti function switch(R.H)SteeringSwitch panel(Front)Multi function switch(L.H)Safety leverJoystick control leverPower Max. buttonOne touch decel buttonDozer blade LeverAir conditioner and heater controllerFully adjustable suspension seat
Wide, Comfortable Operating SpaceAll the controls are designed and positioned according to the latest ergonomic research.Reinforced pillars have also been added for greater cab rigidity.
The best working conditions in a pleasant environment.
Operator’s Comfort is Foremost. Wide Cab Exceeds Industry Standards.
Technology in Cab DesignTechnology in Cab Design
Adjustable Steering Column
60mm
30
Storage box and Cup HolderAn additional storage box and cupholder are located behind operator’sseat, and it keeps food andbeverages cool or hot.
4 5
Radio/USB Player & Remote Control Switch
Self Diagnosis SystemThe CPU controller diagnoses problems in theCAPO system caused by electric and hydraulicmalfunctions and displays them on the LCDmonitor of the cluster through error codes. Thiscontroller has the capacity to identify 48 distincttypes of errors. As the information from thisdevice, such as engine rpm, main pump deliverypressure, battery voltage, hyd. temperature,and the state of all types of electric switches,provides the operator with a much more exactstate of machine operating condition. This makes the machine easier to troubleshootwhen anything does go wrong.
Arm Flow Regeneration SystemArm flow regeneration valve provides smootharm-in operation without cavitations.
Boom & Arm Holding System The Holding valves in the main control valveprevents the boom & arm from dropping over anextended period in neutral position.
One Touch Decel SystemWhen the one touch decel switch is pressed,CPU controller controls the accel actuator toreduce engine speed to low idle. And then theone touch decel switch is pressed again, theengine speed recovers.
Auto Deceleration SystemWhen remote-control valvesare in neutralposition morethan 4 seconds,CPU controllerinstructs the
accel actuator to reduce engine speed to1200rpm. This decreases fuel consumption andreduces cab noise levels.
Max. Flow Cut-off SystemFor precise control and finishing work, the Max.Flow Cut-off System reduces pump flow, thusallowing smooth operation.
Pump Flow Control SystemIn neutral position: Pump flow is reduced to aminimum to eliminate power loss. In operation: Maximum pump flow is delivered tothe actuator to increase the speed. Withmovement of the control lever, pump flow isautomatically adjusted and the actuator speedcan be proportionally controlled.
Hydraulic Damper in Travel PedalImproved travel controllability & feeling byshock reducing when starting and stopping.
Advanced CAPO SystemThe advanced CAPO(Computer Aided Power Optimization) system maintains engine and mutual pumppower at optimum levels. Mode selections are designed for various work loads and maintaining highperformance while reducing fuel consumption. Features such as auto deceleration and power boost are included in the system. The system monitorsengine speed, coolant temperature, and hydraulic oil temperature. Contained within the system are selfdiagnostic capabilities which are displayed by error codes on the cluster.
Automatic Engine Overheat PreventionIf the engine coolanttemperature gets toohigh, the CPU controllerlowers the engine speedand cools the engine.
Anti Restart SystemThe new system protectsthe starter from re-starting during engineoperation, even if theoperator accidentallyturns the start key again.
Power boost control SystemWhen the power boostsystem is activated,digging power increasesabout 10%.It is especially usefulwhen extra power is
temporarily needed, for instance, when digginghard earth and rock, or if the bucket teeth arestopped by a stubborn tree root.
Automatic Warming-up SystemAfter the engine isstarted, if the enginecoolant temperature islow, the CPU controllerincreases the enginespeed and automatically
increases the pump flow rate to warm up theengine more effectively.
Drive signal
Main control valve
Main reliefvalve
Power boostsolenoid valve
Travel reversesolenoid valve
Engine speedsensor
Main pump Pilot pump
EPPR valve
Drive signal
ProlixResistor
Drive signal
Pressure switch signal
P M
Engine
Fuel injectionpump
Accelactuator Hyd temp
sensor
LH controllever
Serial Communication(-)
Serial Communication(+)
Coolant temperature signal
Mot
or d
rive
sign
al
Pot
entio
met
er s
igna
l
Eng
ine
spee
d se
nsor
sig
nal
Auto deceleration pressure switch
Hyd temperature signal
Dozer
Option
Boom 1
Bucket
Travel motor
Swing
Travel
Boom 2
Arm 1
Max flow COsolenoid valve
Max flowCO valve
Drive signal
RH controllever
Accel dial signal
signalsignal
CPU controller
Coolanttemp sensor
Arm 2
P1 P2
CN-19
CN-19B
Transmission
Travel forwardsolenoid valve
Battery
CN-19A
Boom priorityvalve
Boom prioritysolenoid valve
Cluster
Accel dial
Power boostbutton
Optionbutton
One touchdecel buttonHorn
Travel lever
ADVANCED CAPO SYSTEM NEW MODE CONTROL SYSTEM
Advanced Hydraulic SystemAdvanced Hydraulic System POWER MODEH mode : High powerS mode: Standard power
USER MODEM mode: Maximum PowerU mode: Memorizing Operator’s Preferable
Power Setting
WORK MODEHeavy duty
General
Breaker
6 7
*Photo may include optional equipment.
Large Toolbox & Safe FootholdsAnti-slip footholds and wide toolbox improved safety and convenience.
Powerful and PreciserSwing ControlImproved shock absorbingcharacteristics make stopping aprecise and smooth action
Powerful Dozer Blade andDozer Blade Cylinder GuardLarge size blade’s plate and coverthat protect cylinder improvedefficiency of work and durability ofequipment.
Increased Higher Performance and durability
CUMMINS B5.9-C ENGINEThe six cylinders, turbo-charged, 4 cycle,charger air cooled engine is built for power,reliability, economy and low emissions.
A More Reliable Way To Reach YourDream.The Cummins B5.9-C engine has been designedwith 40% fewer parts than the competition. Thatmeans there's less that can go wrong when youneed it most. It also means fewer parts toinventory. Repairs are simplified because nospecial tools are needed for maintenance. Theweight of the machine is reduced withoutsacrificing strength.The B5.9-C engine is capable of reachingemission standards without electronic enginecontrols. You get a proven power plant thatmeets ecological concerns, without paying apremium for technology you don’t need.
Reinforced Bucket and BucketLinkageSealed and adjustable bucket linkage providesless wear of pins and bushes as well as silentoperation. The design includes bucket linkdurability and anti wearcharacteristics. Additional reinforcementplates on cutting edgesection. Reinforced bucketis made with thicker steeland additional lateral plate.
Strong and Stable Lower FrameReinforced box-section frame is all welded, low-stress, high-strength steel. It guarantees safety and resistance against external impact when driving on rough ground andworking on wet sites through high tensile strength steel panels, with protection cover fortransmission.
Minimization of Shock andVibration through Cab MountingSystem
The application ofViscous Mountingto the cabinsupport providesthe operator witha much improved
ride. The operator work efficiency willincrease as the shock and noise level in thecabin decreases.
8 9
Cummins B5.9-C Tier II
Increased Higher Performance and durability
*Photo may include optional equipment.
Reliability and Serviceability
Reliability and Serviceability
Easy to Maintain Engine ComponentsThe cooling and preheating system are provided for optimum and immediate operation,guaranteeing longer life for the engine and hydraulic components. Servicing of the engine and hydraulics is considerably simplified due to total accessibility.
Side Cover with Left & Right Swing Open TypeEasy access to vital components gives unrestricted view ofcomponent allows easy maintenance and repair.
Easy to Access and Battery Master SwitchBattery and master switch on equipment forehead enable to checkand maintain easily.
Centralized Electric Control Box andEasy Change Air Cleaner AssemblyElectric control box and Air cleaner are centralized in one or the same compartmentfor easy service.
Highly Efficient Hydraulic PumpA pilot pump has been installed resulting inimproved control sensitivity.
Large Capacity Fuel TankThe capacity of fuel tank is increased toextend the working time.
10 11
*Photo may include optional equipment.
Durability of structure proven throughFEM(Finite Element Method) analysis and long term durability test.
0.51 (0.67)
0.80 (1.05)
0.87 (1.14)
0.92 (1.20)
1.10 (1.44)
1.20 (1.57)
1.34 (1.75)
0.74 (0.97)
0.90 (1.18)
1.05 (1.37)
0.87 (1.14)
0.75 (0.98)
0.45(0.59)
0.70(0.92)
0.75(0.98)
0.80(1.05)
0.96(1.26)
1.00(1.31)
1.15(1.50)
0.65(0.85)
0.80(1.05)
0.92(1.20)
0.75(0.98)
0.65(0.85)
700(27.6)
1,000(39.4)
1,090(42.9)
1,150(45.3)
1,320(52.0)
1,400(55.1)
1,550(61.0)
985(38.8)
1,070(42.1)
1,290(50.8)
1,140(44.9)
1,790(70.5)
820(32.3)
1,120(44.1)
1,210(47.6)
1,270(50.0)
1,440(56.7)
1,520(59.8)
1,670(65.7)
-
-
-
-
-
570(1260)
700(1540)
740(1630)
770(1700)
830(1830)
850(1870)
920(2030)
770(1700)
810(1790)
890(1960)
900(1980)
880(1940)
Specifications
Engine
Water cooled, 4 cycle Diesel,6-Cylinders in line, direct injection,turbocharged, charge air cooled andlow emission
166 HP (124 kW) at 1,950 rpm153 HP (114 kW) at 1,950 rpm168 PS (124 kW) at 1,950 rpm155 PS (114 kW) at 1,950 rpm68.4 kgf.m(495 lbf.ft) at 1,500 rpm102 x 120 mm(4.02” x 4.72”) 5,880 cc (359 cu in)2 x 12V x 100 AH24 V, 4.5 kW24V, 70A
Type
Ratedflywheelhorsepower
Max. torqueBore x strokePistonBatteriesStarting motorAlternator
Pilot pressure operated joysticks and pedals with detachable leverprovide almost effortless and fatigueless operation.
Reinforced box - section frame is all-welded, low-stress. Rear dozer blade andoutrigger are available. A bolt-on design. Front outrigger lug is pin-on.
A very useful addition for leveling and back filling orclean-up work. Can be mounted on the rear.Indicated for max. operation stability when digging andlifting. Can be mounted on the rear.
Operating weight (approximate)
Major component weightUpperstructure 8,950 kg (19,730 lb)Counterweight 3,400 kg ( 7,500 lb)Boom (with arm cylinder) 1,480 kg ( 3,260 lb)
UndercarriageOperating Weight
kg (lb)Front - outrigger+Rear-blade 20,500 (45,200)
Four outrigger 20,600 (45,400)Standard equipment
Operating weight
Operating weight, including 5.65 m (18’ 6”) boom, 2.90 m (9’ 6”) arm, SAEheaped 0.80 m3 (1.05 yd3) backhoe bucket, lubricant, coolant, full fuel tank,hydraulic tank and the standard equipment.
Hydraulic system
Two variable displacement piston pumps 2 x 220 /min (58.1 US gpm / 48.4 UK gpm)Gear pump
Pilot control Two joysticks with one safety lever(LH): Swing and arm, (RH): Boom and bucket(ISO)
Electric, Dial type
Two lights mounted on the boom and two under the cabin
Control
NEW 7 SERIES ROBEX 200W-7
Backhoe attachment
Buckets
Arms
1.10 (1.44)1.20 (1.57)
1.34 (1.75) 0.74 (0.97)0.90 (1.18)1.05 (1.37)
0.87 (1.14) 0.75 (0.98)
SAE heaped m3 (yd3)
SAE heaped 2,900(9’ 6”)
2,400(7’ 10”)
2,000(6’ 7”)Arm
Weight kg(lb)Width mm (in)
Boom
CECE heaped Without side cutters With side cutters
Capacity m3 (yd3)Recommendation mm(ft.in)
: Standard backhoe bucket: Heavy duty
: Rock-Heavy duty bucket: Slope finishing bucket
: Applicable for materials with density of 2,000 kg / m3 (3,370 lb/ yd3) or less: Applicable for materials with density of 1,600 kg / m3 (2,700 lb/ yd3) or less: Applicable for materials with density of 1,100 kg / m3 (1,850 lb/ yd3) or less
5,650 (18’ 6”)
Boom and arms are of all-welded, low-stress, full-box section design. 5,650 mm(18’ 6”) mono boom and 2,000 mm(6’ 7”), 2,400 mm(7’ 10”), 2,900 mm(9’ 6”) arms are available. Buckets are all-welded, high-strength steel implements.
2,900 (9’ 6”)
990 (2,180)
2,400 (7’ 10”)
950 (2,090)
2,000 (6’ 7”)
860 (1,890)
Bucket digging force
Arm crowdforce
133.4 [145.5]13,600 [14,840]29,980 [32,710]
152.0 [165.8]15,500 [16,910]34,170 [37,280]
135.3 [147.6]13,800 [15,050]30,420 [33,190]
142.2 [155.1]14,500 [15,820]31,970 [34,880]
133.4 [145.5]13,600 [14,840]29,980 [32,710]
152.0 [165.8]15,500 [16,910]34,170 [37,280]
112.8 [123.1]11,500 [12,550]25,350 [27,650]
117.7 [128.4]12,000 [13,090]26,460 [28,870]
133.4 [145.5]13,600 [14,840]29,980 [32,710]
152.0 [165.8]15,500 [16,910]34,170 [37,280]
97.1 [105.9]9,900 [10,800]
21,830 [23,810]
101.0 [110.2]10,300 [11,240]22,710 [24,770]
Note : Arm weight including bucket cylinder and linkage. Standard arm
Arm Length
Weight
mm(ft.in)
kg(lb)
kNkgflbf
kNkgflbf
kNkgflbf
kNkgflbf
SAE
ISO
SAE
ISO
Remark
[ ]:Power Boost
2,400 mm (7’ 10”) 2,900 mm (9’ 6”)2,000 mm (6’ 7”)
Digging force
12 / 13
0.51 (0.67) 0.80 (1.05)0.87 (1.14)0.92 (1.20)
B B' C
D
E
A
A'
F
� 200w-7
Dimensions & Working ranges
AP
Q
IJ
C
D,D'
NMHB
E
O FG
KL
200w-7 200w-7
Dimensions
Working ranges
Wheel baseTreadGround clearance of counterweightTail swing radiusRear-end lengthOverall width of upperstructureOverall height of capMin. ground clearanceOverall width of lower structureGround clearance of blade upDepth of blade downHeight of bladeWidth of bladeGround clearance of outrigger upDepth of outrigger downOverall width of outrigger