Figure 1 Step 2: Rack Assembly Position the port and starboard brackets onto the center of the cooler rack rear tube as shown in figure 2. Attach the brackets using two 8mm x 55mm hex bolts, washers and locknuts. Finger tighten only. Attach this assembly to the column tube at the desired position and secure using one 10mm x 70mm hex bolt, washer and locknut as shown in Figure 3. Tighten securely, then reverse the nut until the brackets rotate freely on the column tube. Now securely tighten the two 8mm x 55mm bracket bolts. Step 1: Attaching Column Tube to the Receiver Tube The Column Tube is attached to the Receiver Tube using one 12mm x 80mm hex bolt, flat washer and locknut, and the 12mm curved clevis pin. Attach the Column Tube as shown in figure 1. Tighten the 12mm hex bolt securely, then reverse the nut until the column tube is free to rotate. Stack-Rack Vertical Receiver Mounted Cargo Rack Assembly and Use Instructions Assembly Tools Required: Adjustable Crescent Wrench 13mm Box Wrench or Socket 16mm Box Wrench or Socket 18mm Box Wrench or Socket Stack-Rack Parts Overview General Purpose Rack Port Mounting Bracket (2) Column Tube Tie-Down Rings Receiver Tube Starboard Mounting Bracket (2) Cooler Rack Receiver Tube Column Tube 12mm x 80mm Hex Bolt 8mm x 55 mm Hex Bolt Figure 3 Step 3: Repeat Step 2 for the general purpose rack. Position the general purpose rack at the desired location on the column tube and secure using the same procedure in Step 2. 10mm x 70mm Hex Bolt Receiver Clevis Pin Hole Figure 2 12mm Clevis Pin & Cotter Pin 12mm Washer and Locknut this side 10mm Washer and Locknut this side Port Bracket Starboard Bracket
2
Embed
Stack-Rack Vertical Receiver Mounted Cargo Rack ...the Stack-Rack before securing the receiver tube into the receiver with a locking pin. Step 2: You may place a cooler, storage trunk,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Figure 1
Step 2: Rack Assembly
Position the port and starboard brackets onto the center of
the cooler rack rear tube as shown in figure 2. Attach the
brackets using two 8mm x 55mm hex bolts, washers and
locknuts. Finger tighten only. Attach this assembly to the
column tube at the desired position and secure using one
10mm x 70mm hex bolt, washer and locknut as shown in
Figure 3. Tighten securely, then reverse the nut until the
brackets rotate freely on the column tube. Now securely
tighten the two 8mm x 55mm bracket bolts.
Step 1: Attaching Column Tube to the Receiver Tube
The Column Tube is attached to the Receiver Tube
using one 12mm x 80mm hex bolt, flat washer and
locknut, and the 12mm curved clevis pin. Attach the
Column Tube as shown in figure 1. Tighten the
12mm hex bolt securely, then reverse the nut until
the column tube is free to rotate.
Stack-Rack
Vertical Receiver Mounted Cargo Rack Assembly and Use Instructions
Assembly Tools Required: Adjustable Crescent Wrench 13mm Box Wrench or Socket 16mm Box Wrench or Socket 18mm Box Wrench or Socket
Stack-Rack Parts Overview
General Purpose Rack
Port Mounting Bracket (2)
Column Tube Tie-Down Rings
Receiver Tube
Starboard Mounting Bracket (2)
Cooler Rack
Receiver Tube
Column Tube
12mm x 80mm Hex Bolt
8mm x 55 mm Hex Bolt
Figure 3 Step 3: Repeat Step 2 for the general
purpose rack. Position the general purpose
rack at the desired location on the column
tube and secure using the same procedure in
Step 2.
10mm x 70mm Hex Bolt
Receiver Clevis Pin Hole
Figure 2
12mm Clevis Pin & Cotter Pin
12mm Washer and Locknut this side
10mm Washer and Locknut this side
Port Bracket
Starboard Bracket
Instructions for using the Viking Stack-Rack
Failure to read and follow all instructions may result in property damage, serious injury or death.
Never exceed the total maximum load capacity of 300 Lbs. (150 lbs. maximum each frame).
Use appropriate tie-down straps to secure the load and always assure the load is balanced on the rack system.
Always use caution to avoid pinch points during assembly, loading or use of the rack system.
Never allow any cargo to extend beyond 36 inches from the tail lights of the vehicle.
Never begin transporting any object until you are certain it is secured to the cargo frame(s).
Never use for transportation of pets or live animals.
Never load an object that is not fully contained within the rack frame(s).
Always use additional caution during reverse operation of the vehicle.
Always inspect for damage during storage, missing parts, etc. before each use.
Store the Stack-Rack appropriately when not in use to provide years of trouble-free use.