ST102-SD Installation Guide Package Contents www.dfi.com • 1 ST102-SD system unit • Mounting screws for Mini PCIe modules • Mounting screws for M.2 modules • 1 Quick Installation Guide • 1 CD disk includes: - Drivers / Manual Panel Rear View Front View DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the installation process, please refer to the user's manual. LAN Ports HDMI USB 3.0 DC-in DVI-D (DVI-I connector) DVD Drive Power Button Line-out Mic-in HDD LED Power LED USB 2.0 Notes: The HDMI is a DP++/HDMI combo port but can only transmit HDMI signals (unless wired as a DP++ port). Please plug in an HDMI cable with the right orientation and alignment to avoid damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not inserted correctly. Please see a video at https://youtu.be/SUj07rfN5l8 for detailed instructions. Align this edge with the left side of the connector Angled-corner (up) Angled-corner Aligning side (left) pin
7
Embed
ST102-SD Installation Guide - DFI · 1 ST102-SD Installation Guide Package Contents • 1 ST102-SD system unit • Mounting screws for Mini PCIe modules • Mounting screws for M.2
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
ST102-SD Installation GuidePackage Contents
www.dfi.com
• 1 ST102-SD system unit
• Mounting screws for Mini PCIe modules
• Mounting screws for M.2 modules
• 1 Quick Installation Guide
• 1 CD disk includes:
- Drivers / Manual
Panel
Rear View
Front View
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the installation process, please refer to the user's manual.
LAN PortsHDMI USB 3.0
DC-in
DVI-D(DVI-I connector)
DVD Drive Power Button
Line-out
Mic-in
HDD LED
Power LED
USB 2.0
Notes:The HDMI is a DP++/HDMI combo port but can only transmit HDMI signals (unless wired as a DP++ port). Please plug in an HDMI cable with the right orientation and alignment to avoid damage to the connector. You should feel resistance (due to a pin on the right) if the cable is not inserted correctly. Please see a video at https://youtu.be/SUj07rfN5l8 for detailed instructions.
Align this edge with the left side of the connectorAngled-corner
(up)
Angled-cornerAligning side(left) pin
2
4. Slide the cover backwards to open the system. The SODIMM sockets and SATA drive bay are readily accessible after removing the chassis cover.
Removing the Chassis Cover
Installing internal components requires you to remove the chassis cover first. Please observe the following guidelines and follow the procedure to open the system.
1. Make sure the system and all other peripheral devices connected to it have been powered off.
2. Disconnect all power cords and cables.
3. The 2 mounting screws on the rear side of the system are used to secure the cover to the chassis. Remove these screws and put them in a safe place for later use.
Mounting screw
SATA drive bay ODD drive bay
3
Installing a Memory Module
Grasp the module by its edges and align the memory’s notch with the socket’s notch; then insert the memory into the socket at an angle and push it down until you feel a click.
The system board is equipped with two memory slots. Please use the following procedure to install SODIMM modules.
DIMM1
DIMM2
Notes:
1. The system supports dual-channel configuration. To enable dual-channel, populate both SODIMM sockets.
2. If installing only one memory module, please install it on the memory socket labeled DIMM1 (the one closer to the center of the board).
3. The SODIMM sockets can only accommodate DDR4 memory modules. Please do not install other types of memory modules.
4
Installing a SATA Drive
The system can accommodate one 2.5” SATA drive. Please use the following procedure to install a 2.5” SATA drive.
1. Remove the 2 mounting screws that secure the drive bay to the system.
Mounting screw
HDD bracket
Mounting screw
2. Align the mounting holes on the SATA drive with the mounting holes on the HDD bracket.
SATA mounting screws
HDD bracket
Mounting screw
5
3. Use the mounting screws provided in the drive bay kit to attach the HDD bracket onto the drive bay and secure the drive in place.
(on the drive bay’s bottom side)HDD bracket mounting holes
HDD bracket mounting screws
Mounting screw
SATA mounting screws
6
4. Place the SATA drive bay back in the chassis and install the SATA drive bay using the mounting screws you removed in step 1.
Mounting screw
SATA power/data cable
5. Connect the SATA data/power cable to the SATA drive (refer to the above picture). Make sure the other end of the SATA data/power cable is connected to the connectors on the system board (refer to the picture below).
SATA data connector
SATA power connector
7
Board Layout and Jumper Settings
Clear CMOS Data JP5 Normal 1-2 On (default) Clear CMOS 2-3 On
www.dfi.com A52801917
Auto Power-on Select JP1Power-on via power button 1-2 On