AS1000-M3 AS1000-M5 AS2000-01 AS2000-02 AS3000-02 AS3000-03 AS4000-02 AS4000-03 AS4000-04 AS5000-02 AS5000-03 AS5000-04 Model Port size Applicable cylinder bore size (mm) Effective area (mm 2 ) Effective area (mm 2 ) Flow rate ( /min (ANR)) Flow rate ( /min (ANR)) Weight (g) M3 x 0.5 M5 x 0.8 1/8 1/4 1/4 3/8 1/4 3/8 1/2 1/4 3/8 1/2 20 90 340 340 810 810 1,670 1,670 1,670 2,840 4,270 4,270 0.3 1.4 5.2 5.2 12.3 12.3 25.5 25.5 25.5 44 66 66 20 80 250 250 810 810 1,670 1,670 1,670 2,840 4,270 4,270 0.3 1.2 3.8 3.8 12.3 12.3 25.5 25.5 25.5 44 66 66 4.7 33 90 115 130 124 221 214 205 242 233 224 2.5, 4, 6 6, 10, 16, 20, 25 Air 1.5 MPa (1.05 MPa) 1 MPa (0.7 MPa) 0.05 MPa (0.1 MPa) –5 to 60°C (No freezing) 8 turns (10 turns) Free flow Controlled flow 20, 25, 32, 40 32, 40, 50, 63 40, 50, 63 80, 100 40, 50, 63 80, 100 Model/Flow Rate and Effective Area Note) Flow rate values are measured at 0.5 Mpa and 20°C. Note) ( ): Values for AS1000. Note) AS1000 with nipple: AS1000-M5-N Fluid Proof pressure note) Max. operating pressure note) Min. operating pressure note) Ambient and fluid temperature Number of needle rotations note) Specifications Accessory Description Part no. Applicable model Body size 1 2 3 4 5 M5 AS 1 000 Bore size Bore size Applicable series M3 M5 01 02 03 04 M3 x 0.5 M5 x 0.8 Rc 1/8 Rc 1/4 Rc 3/8 Rc 1/2 AS1000 AS1000 AS2000 AS2000/3000/4000/5000 AS3000/4000/5000 AS4000/5000 Thread type Nil Metric thread (M3, M5) Rc NPT G How to Order M-5N AS1000 Nipple N F Option H (1) L (2) Note 1) AS5000 is available as special. AS1000 is not applicable. Note 2) AS1000, AS2000 are not applicable. High temperature (–5 to 80°C) Low temperature (–30 to 60°C) Speed Controller: Standard Type Series AS In-line Type AS4000 AS2000 AS1000-M5 AS1000-M3 AS3000 JIS Symbol M3, M5 standard 1 8 8 3 2 1 2 1 1 4 , standard standard standard standard Caution Be sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 15-8-6 to 15-8-8 for Precautions on every series. Compact size saves space. Speed may be accurately controlled even at low speeds. Constant speed easily set. Retainer prevents an accidental loss of needle. 15-9-28
19
Embed
Speed Controller: Standard Type Series AS NBR Electroless nickel plated Electroless nickel plated Electroless nickel plated Electroless nickel plated Electroless nickel plated Electroless
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
AS1000-M3
AS1000-M5
AS2000-01
AS2000-02
AS3000-02
AS3000-03
AS4000-02
AS4000-03
AS4000-04
AS5000-02
AS5000-03
AS5000-04
Model Port sizeApplicable cylinder
bore size (mm)Effective area(mm2)
Effective area(mm2)
Flow rate(� /min (ANR))
Flow rate(� /min (ANR))
Weight(g)
M3 x 0.5
M5 x 0.8
1/8
1/4
1/4
3/8
1/4
3/8
1/2
1/4
3/8
1/2
20
90
340
340
810
810
1,670
1,670
1,670
2,840
4,270
4,270
0.3
1.4
5.2
5.2
12.3
12.3
25.5
25.5
25.5
44
66
66
20
80
250
250
810
810
1,670
1,670
1,670
2,840
4,270
4,270
0.3
1.2
3.8
3.8
12.3
12.3
25.5
25.5
25.5
44
66
66
4.7
33
90
115
130
124
221
214
205
242
233
224
2.5, 4, 6
6, 10, 16, 20, 25
Air
1.5 MPa (1.05 MPa)
1 MPa (0.7 MPa)
0.05 MPa (0.1 MPa)
–5 to 60°C (No freezing)
8 turns (10 turns)
Free flow Controlled flow
20, 25, 32, 40
32, 40, 50, 63
40, 50, 6380, 100
40, 50, 6380, 100
Model/Flow Rate and Effective Area
Note) Flow rate values are measured at 0.5 Mpa and 20°C.
Note) ( ): Values for AS1000.
Note) AS1000 with nipple: AS1000-M5-N
Fluid
Proof pressure note)
Max. operating pressure note)
Min. operating pressure note)
Ambient and fluid temperature
Number of needle rotations note)
Specifications
AccessoryDescription Part no. Applicable model
Body size12345
M5AS 1 000
Bore sizeBore size Applicable series
M3M501020304
M3 x 0.5M5 x 0.8Rc 1/8Rc 1/4Rc 3/8Rc 1/2
AS1000AS1000AS2000
AS2000/3000/4000/5000AS3000/4000/5000
AS4000/5000
Thread type
NilMetric thread (M3, M5)
RcNPT
G
How to Order
M-5N AS1000Nipple
NF
OptionH (1)
L (2)
Note 1) AS5000 is available as special. AS1000 is not applicable.
Note 2) AS1000, AS2000 are not applicable.
High temperature (–5 to 80°C)Low temperature (–30 to 60°C)
Speed Controller: Standard Type
Series AS In-line Type
AS4000
AS2000 AS1000-M5AS1000-M3
AS3000
JIS Symbol
M3, M5 standard1 8
83
21
21
1 4, standardstandardstandardstandard
CautionBe sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 15-8-6 to 15-8-8 for Precautions on every series.
Compact size saves space. Speed may be accurately controlled even at low speeds. Constant speed easily set. Retainer prevents an accidental loss of needle.
15-9-28
Needle Valve/Flow Characteristics
Construction: AS1000-M3
Construction: AS1000-M5
No. Description Material Noteq
w
e
r
t
y
u
i
o
Body BBody NeedleLock nutHandleU sealNeedle guideO-ringO-ring
Series ASSpeed Controller: Standard TypeIn-line Type
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
Construction: AS4000
Construction: AS5000
Construction: AS2000/3000
No. DescriptionModel
Body Needle ∗
Lock nut ∗
ValveO-ringSpring
Zinc alloyBrassBrass
Aluminum alloyBrass
Carbon steel
Component Parts
Component Parts
Component Parts
Replacement Parts
q
w
r
No. DescriptionModel
143022143021143023
142831428414282
e
t
y
No. Description Material NoteBody CapCross-recessed head cap screwE type snap ringHandleRingLock nutNeedleO-ring
Aluminum alloyRolled steelSteel wire
Stainless steelZinc alloySteel wireZinc alloy
Aluminum alloyNBR
ChromatedZinc chromated
4 x 0.7 x 8JIS B 2805 Nominal 6Black zinc chromate plated
∗ Electroless nickel plated
q
w
e
r
t
y
u
i
!2
Zinc chromated
143112
ValveSpringO-ring
Replacement PartsNo. Description Material Parts no.
Stainless steelNBR
143145143146143147
NBR, Brasso
!0
!11
No. Description Material NoteBody CapCross-recessed head cap screwE type snap ringHandleRingLock nutNeedleO-ring
Aluminum alloyRolled steelSteel wire
Stainless steelZinc alloy
Stainless steelZinc alloy
Aluminum alloyNBR
ChromatedNickel plated
M4 x 0.7 x 8 Nickel platedJIS B 2805 Nominal 6
Chromated
q
w
e
r
t
y
u
i
!2
ChromatedChromated
JIS B 2401 P12
ValveSpringSeal
Replacement PartsNo. Description Material Parts no.
Stainless steel
NBR
141431414414147
NBR, Stainless steelo
!0
!1
AS2000 AS3000
AS2000 AS3000
Series AS
15-9-30
Dimensions: AS1000-M3
Dimensions: AS2000/3000
Dimensions: AS1000-M5
Dimensions: AS4000
Dimensions: AS5000
Dimensions
Max. Min.L1 L2 L3 L4 L5 L6
L7L8 DModel Bore size
AS2000-01AS2000-02AS3000-02, 03
Rc Rc
Rc ,
404056
303045.5
555.25
172325
1011.513.2
15.51720.6
54.55668
5051.561
162026
4.54.55.5
1 8
83
1 41 4
Male M5 x 0.8Female M5 x 0.8
2-port size
Effective thread depth 6
2-1/4 to 1/2
2-M4 x 0.7 Effective thread depth 7
2-1/4 to 1/2
15-9-31
Series ASSpeed Controller: Standard TypeIn-line Type
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
JIS Symbol How to Order
Thread typeRc
NPTG
NilNF
Material for handleResinMetal
Nil2
Port size1/43/8
0203
02AS3500
Caution
Specifications
Port size
Applicable cylinder bore size (mm)
Proof pressure
Max. operating pressure
Min. operating pressure
Ambient and fluid temperature
Number of needle rotation
Weight
Free flow
Controlled flow
Flow rate (�/min (ANR))
Effective area (mm2)
Flow rate (�/min (ANR))
Effective area (mm2)
40, 50, 63
1.5 MPa
1 MPa
0.05 MPa
–5 to 60°C (No freezing)
8 turns
130 g (Metallic handle: 140 g)
810
12.3
810
12.3
Model Resin handle
Metal handle
Model/Specifications
1/4 3/8
AS3500-02
AS3500-02-2
AS3500-03
AS3500-03-2
Note) Flow rate values are measured at 0.5 MPa and 20°C.
Needle Valve/Flow Characteristics AS3500
Metal handleResin handle
Speed Controller: Standard Type
Series AS In-line Push Locking Type
Lock speed setting, with the touch of a buttonIt can be locked only by pushing the handle after adjustment.
Convenient opening indication scaleThe opening indication scale for the needle valve is provided on the handle to facilitate speed adjustments.
Easy speed control at low flow volume rangesPossible to control the mass velocityConstant handle constructed of metal to withstand heavy usage In addition to the standard handle made of resin, a heavy-duty metal handle is also available.
Retainer prevents an accidental loss of needle
Be sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and Common Precautions on the products men-tioned in this catalog, and refer to pages 15-8-6 to 15-8-8 for Precau-tions on every series.
Flo
w r
ate
(�/m
in (
AN
R))
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
15-9-34
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
Speed Controller: Standard TypeIn-line Push Locking Type
15-9-35
Series AS
Construction
Component PartsNo. Description NoteMaterial
Dimensions
Replacement Parts
Body ValveCapNeedle
q
w
e
r
t
y
Handle
Aluminum alloyNBR
Rolled steelBrassPOM
Zinc alloy
Chromate plated
Electroless nickel plated
BlackBlack
No. Part no.Material14284NBR
DescriptionO-ring
Speed Controller: Standard Type
Series AS Large Flow In-line Type
Caution
AS420-02
AS420-03
AS420-04
AS500-06
AS600-10
AS800-12
AS900-14
AS900-20
ModelPortsize
Applicablecylinder
bore size (mm)Effective
area (mm2)Effective
area (mm2)Flow rate
(� /min (ANR))Flow rate
(� /min (ANR))
Weight(g)
2,500
5,000
6,600
10,100
15,100
35,400
52,000
57,800
38
77
100
154
230
540
792
880
3,600
4,800
6,700
8,100
16,900
38,500
47,500
60,800
55
74
102
123
258
586
724
926
0.36
0.7
1.4
3.3
3.3
63, 80, 100, 125
Free flow Controlled flow
160, 180, 200, 250
140, 160, 180, 200
Model
Note) Flow rate values are measured at 0.5 MPa and 20°C.
Note 1) AS800 is available as special.Note 2) AS900 is available as special.
High temperature (–5 to 80°C)Low temperature (–30 to 60°C)
Nil None
JIS Symbol
Be sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to pages 15-8-6 to 15-8-8 for Precautions on every series.
Flo
w r
ate
(�/m
in (
AN
R))
Effe
ctiv
e ar
ea (m
m2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate
(�/m
in (
AN
R))
Effe
ctiv
e ar
ea (m
m2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate
(�/m
in (
AN
R))
Effe
ctiv
e ar
ea (m
m2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
AS500/600AS420 AS800/900
1/2 standard3/4 standard1 standard
1 1/4 standard1 1/2 standard
AS900
AS420
AS600
AS500
AS800
Able to control and set a constant speed easily. Speed may be accurately controlled even at low speed. Retainer prevents accidental loss of needle.
1.6Note 1) Flow rate values are measured at 0.5 MPa and 20°C.Note 2) Meter-in type not available on AS1200-M3, AS1400-M3. Note 3) Distinction between meter-out/meter-in types by appearance.
Those are distinguished by the lock nut. The meter-out type is electroless nickel plated, while the meter-in type is black zinc chromate plated.
Note 4) AS1200, AS1400, AS22�0 are electroless nickel plated as standard. (N specifications)
How to Order
01 SAS 2 2 0 0Body size1234
M3, M5 standard1 8
83
21
1 4
TypeDirect cylinder
elbow type
Direct cylinderflat elbow type
2
4
Control typeMeter-outMeter-in
01
Option
Bore size
SKN
NoneWith seal
Nil
Symbol Bore sizeApplicable
series
M3
M5U10/32
01020304
M3 x 0.5
M5 x 0.810-32UNF
1/81/43/81/2
AS1200-M3AS1400-M3
AS12�0-M5AS12�0-U10/32
AS22�0-01AS22�0-02AS32�0-03AS42�0-04
Hexagonal lock nutElectroless nickel plated
M3 x 0.5
2.5, 4, 6
1.05 MPa
0.7 MPa
0.1 MPa
P.15-11-3
AS1200-M5
AS2200-02AS2200-01
AS4200-04
AS3200-03
Minimizes installation time and costFittings and tubing are not necessary because this type screws directly into the actuator. Thus, piping labor and cost can be eliminated.
Body swivels 360°Swivel type allows free setting of piping.
Speed may be accurately controlled even at low speeds. Able to control and set a constant speed easily. Retainer prevents accidental loss of needle.
, standardstandardstandard
AS1400-M3
AS1200-M3
∗ If more than one option isrequired, write option partnumbers in the order of“S”, “K”, “N”.
CautionBe sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 15-8-6 to 15-8-8 for Precautions on every series.
15-9-25
Series ASSpeed Controller: Standard TypeElbow Type (Metal Body)
M3 x 0.5 M3 x 0.5 4.5 6.6 23.5 21.5 8 5 5 20.5 18.5
Max. Min. Max. Min.L1
L2 A(2)
L3H(1)T2T1 D1 D2Model
M5 x 0.8
10-32 UNF
1/8
1/4
3/8
1/2
M5 x 0.8
10-32 UNF
1/8
1/4
3/8
1/2
8 10 28.3 10.3 9 9 25 22.2
12 (12.7)
17 (17.5)
19
24 (23.8)
18
27.2
30
38.5
36.4
40.8
46.9
55.6
25.5
31.4
35.8
41.9
50.6
14.1
18
20.8
26.7
14.3
18
22.5
27.5
14.6
19.5
24.3
28.5
32.4
34.8
40.6
47.4
27.4
29.8
35.6
42.4
Note 1) ( ) are the dimensions of “NPT” thread. Note 2) Reference thread dimensions after installation.
AS1200-M3
AS1200-M5
AS1200-U10/32
AS22�0-01
AS22�0-02
AS32�0-03
AS42�0-04
(Hexagon width across flats)
(Hexagon width across flats)
15-9-27
Series ASSpeed Controller: Standard TypeElbow Type (Metal Body)
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
Model/ Specifications
How to Order
Tamper Proof Speed ControllerStandard Type
Series AS�2�0-TElbow Type (Metal Body)
JIS Symbol
1/410-32 UNFPort size
Applicable cylinder bore size (mm)
Fluid
Proof pressure
Max. operating pressure
Min. operating pressure
Ambient and fluid temperature
Number of needle rotations
Flow rate (l/min (ANR))
Effective area (mm2)
AS42�0-�04
1/8 1/4 3/8
32, 40, 50, 63
1/2
80, 10020, 25, 32, 406, 10, 16, 20, 25
AS12�0-M5 AS12�0-U10/32Specifications Model
Air
1.5 MPa
1 MPa
0.1 MPa
–5 to 60°C (No freezing)
10 turns8 turns
105
1.6
1700
26
920
14
460
7
230
3.5
Note 1) Flow rate values are measured at 0.5 MPa and 20°C.Note 2) Meter-out and meter-in types can be visually differentiated by the flow direction symbol on the resin body. Note 3) Brass parts are all electroless nickel plated, provided as standard.
M5 x 0.8
AS22�0-�01 AS32�0-�03AS32�0-�02AS22�0-�02
01 SAS 2 0 0
Body size1234
M5 standard1/8, 1/4 standard
3/8 standard1/2 standard
2
TypeElbow2
Control01
T
Port sizeSymbol Cylinder side In the side of solenoid valve
requires a special tool for flow adjustment. Order separately with part number, AS-T-1.
With sealNote) When connecting port is either M5
or 10-32 UNF thread, it is not available with seal. With gasket is provided as standard.
Controlled flow(Free flow)
15-9-104
Flo
w r
ate l/m
in (
AN
R)
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate l/m
in (
AN
R)
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate l/m
in (
AN
R)
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate l/m
in (
AN
R)
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Flo
w r
ate l/m
in (
AN
R)
Effe
ctiv
e ar
ea (
mm
2 )
Inlet pressure: 0.5 MPa
Number of needle rotations
Needle Valve/Flow Characteristics
Construction
Component PartsNo. Description Material Note
Electroless nickel plated
Electroless nickel plated
Electroless nickel plated
q
w
e
r
t
y
u
Body A
Body B
Needle
Seat ring
Spring
U seal
O-ring
Zinc alloy
Brass
Brass
Brass
Steel wire
HNBR
NBR
No. Description Material Note
i
o
!0
!1
!2
!3
O-ring
O-ring
Bushing
O-ring
Gasket
Retaining ring for hole type C
NBR
NBR
PBT
NBR
NBR, Stainless steel
Tool steel
AS3200-02
AS3210-02
Meter-out typeM5 typeU10/32 port
Meter-in typeM5 typeU10/32 port
!3
e
t
w
o
u
!4
y
q
!2
w
e
t
o
u
q
!4
!1
!0
i
y
r
e
t
r
i
!0
q
y
!3
!2
!1
o
w
u
15-9-105
Tamper Proof Speed ControllerStandard Type, Elbow Type (Metal Body)
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
Dimensions
L2
øD
1
øD2
L3
A
T2
T1L1
H
L4
øD3
∗ Reference thread dimensions after installation.
Dimensions
AS42�0-N04-ST NPT 1/2NPT 1/2AS42�0-F04-ST G 1/2AS42�0-04-ST Rc 1/2R 1/2
AS32�0-N03-ST NPT 3/8NPT 3/8AS32�0-F03-ST G 3/8AS32�0-03-ST Rc 3/8R 3/8
AS32�0-N02-ST NPT 1/4NPT 1/4AS32�0-F02-ST G 1/4AS32�0-02-ST Rc 1/4R 1/4
AS22�0-N02-ST NPT 1/4NPT 1/4AS22�0-F02-ST G 1/4AS22�0-02-ST Rc 1/4R 1/4
AS22�0-N01-ST NPT 1/8NPT 1/8AS22�0-F01-ST G 1/8AS22�0-01-ST Rc 1/8R 1/8
AS12�0-U10/32-T 10-32 UNF10-32 UNFAS12�0-M5-T M5 x 0.8M5 x 0.8
Model T2 H D1T1 D2 D3 L1 L2 L3 L4 A∗
(He(Hexagon width across flats)xagon width across flats)(Hexagon width across flats)
23.8
24 27.5
19 22.5
19 22.5
17.5
17 18
12.7
12 14.3
8 9
28.5
24.3
24.3
19.5
14.6
9
12
9.5
9.5
7
7
4.5
38.5
30
30
27.2
18
10
63.8
53.7
55.3
40.7
35.6
31
26.7
20.8
22.4
18
14.1
10.3
1.5
1.5
1.5
1.5
1.5
0.7
55.8
47.4
49.3
36.7
31.6
27.4
15-9-106
Model/Specifications
How to Order
Speed Controller Adjustable by Flat Head Screwdriver: Standard Type
Series AS�2�0-DElbow Type (Metal Body)
JIS Symbol
1/410-32 UNFPort size
Applicable cylinder bore size (mm)
Fluid
Proof pressure
Max. operating pressure
Min. operating pressure
Ambient and fluid temperature
Number of needle rotations
Effective area (mm2)
1/8 1/4 3/8
32, 40, 50, 63
1/2
80, 10020, 25, 32, 406, 10, 16, 20, 25
AS12�0-M5 AS12�0-U10/32Specifications Model
Air
1.5 MPa
1 MPa
0.1 MPa
–5 to 60°C (No freezing)
105
1.6
1700
26
920
14
460
7
230
3.5
Note 1) Flow rate values are measured at 0.5 MPa and 20°C.Note 2) Meter-out and meter-in types can be visually differentiated by the flow direction symbol on the resin body. Note 3) Brass parts are all electroless nickel plated, provided as standard.
01 SAS 2 0 0
Body size1234
M5 standard1/8,1/4 standard3/8 standard1/2 standard
2
TypeElbow2
Control01
D
Type adjustable by flat head screwdriver
Port sizeSymbol Cylinder side In the side of solenoid valve
AS42�0-N04-SD NPT 1/2 23.8NPT 1/2AS42�0-F04-SD G 1/2AS42�0-04-SD Rc 1/2 24
R 1/2
AS32�0-N03-SD NPT 3/8NPT 3/8AS32�0-F03-SD G 3/8AS32�0-03-SD Rc 3/8
19 R 3/8
AS32�0-N02-SD NPT 1/4NPT 1/4AS32�0-F02-SD G 1/4AS32�0-02-SD Rc 1/4
19 R 1/4
AS22�0-N02-SD NPT 1/4 17.5NPT 1/4AS22�0-F02-SD G 1/4AS22�0-02-SD Rc 1/4 17 R 1/4
AS22�0-N01-SD NPT 1/8 12.7NPT 1/8AS22�0-F01-SD G 1/8AS22�0-01-SD Rc 1/8 12 R 1/8
AS12�0-U10/32-D 10-32 UNF10-32 UNFAS12�0-M5-D M5 x 0.8 8
M5 x 0.8Model T2 H D1T1 D2 D3 L1 L2 L3 L4 A ∗
9
14.3
18
22.5
22.5
27.5
9
14.6
19.5
24.3
24.3
28.5
4.7
7.2
7.2
9.8
9.8
12.4
31
35.6
40.7
55.3
53.7
63.8
10.3
14.1
18
22.4
20.8
26.7
0.7
1.2
1.2
1.2
1.2
1.2
27.4
31.6
36.7
49.3
47.4
55.8
10
18
27.2
30
30
38.5
15-9-91
Speed Controller Adjustable by Flat Head ScrewdriverStandard Type, Elbow Type (Metal Body)
AS
ASP
ASN
AQ
ASV
AK
ASS
ASR
ASF
1. Products mentioned in this catalog are not designed for the use as stop valve with zero air leakage. A certain amount of leakage is allowed in the product's specifi-cations.
Precautions
1. Check that the lock nut is tightened. A loose lock nut may cause actuator speed changes.
2. Confirm the degree of rotation of the needle valve. Products mentioned in this catalog are retainer type so that the needle is not removed completely. Over rotation will cause damage.
3. Do not use tools such as pliers to rotate the handle.It can cause idle rotation of the handle or damage.
4. Confirm air flow direction. Mounting backwards is dangerous, because the speed adjustment needle will not work and the actuator may lurch suddenly.
5. Adjust needle by opening the needle slowly after having closed it completely. Loose needle valves may cause unexpected sudden actuator extension. When needle valve is turned clockwise, it is closed and cylinder speed decreases. When needle valve is turned counter clockwise, it is open and cylinder speed increases.
6. Do not apply excessive force or shock to the body or fittings with an impact tool.It can cause damage or air leakage.
1. Confirm that PTFE can be used in application. PTFE powder (Polytetrafluoroethylene resin) is included in the seal material. Confirm if the use of it may cause any adverse effect in the system.
1. To install/remove the Flow Control Equipment, tighten/loosen at wrench flat B as close to the thread as possible using the appropriate wrench. Do not apply torque at other points as the product may be damaged. Rotate Body A manually for positioning after installation.
2. Do not use universal type fittings for applications involving continuous rotation. The fitting section may be damaged.
Series AS-F/FE/FG/FM
1. The tightening torque for pipe fittings is as shown in the table. As a rule, they should be tightened 2 to 3 turns with a tool after first tightening by hand. Be careful not to cause damage by over-tightening.
Male thread Suitable screw torque(N·m)
Hexagon widthacross flats
(mm)Adjustable spanner
nominal (mm)
M3
M510/32-UNF
1/8
1/4
3/8
1/2
1/4
1/6 turn afterhand tightening
7 to 9
12 to 14
22 to 24
28 to 30
4.5
8
14
17
21
24
—
100
150
200
200
200
1. Suitable screw torque for a hexagon lock nut is shown in the table below. For standard installation, turn 15 to 30° using tool, after fastening by hand. Pay attention not to over torque the product.
Suitable screw torque(N·m)
0.07
0.3
1
1.5
4
10
Body size
M3
M5
1/8
1/4
3/8
1/2
Selection
Mounting
Selection
Mounting
Tightening Torque
Lock Nut Tightening Torque
Warning
Warning
Warning
Warning
Caution
Caution
Flow Control Equipment PrecautionsBe sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to main text for more detailed precautions on every series.