3 Put the camera support in place and secure it with the 2 MCFAS00197 screws in the front. 4 Secure the back of the camera support with the 2 MCFAS00221 screws. 1 Slide the nose of the Bebop 2 back on.* Caution: make sure you do not damage the GPS during the process. SPARE PARTS / Bebop 2 / Central body To replace the central body under the Bebop 2, you need a T5 screwdriver, a T6 screwdriver, pliers and a box cutter. It is recommended to use the Parrot Toolbox for this operation. REFERENCES: Red Central Body: PF070226AB / White Central Body: PF070203AB 2 Slide the nose forward to remove it.* Caution: make sure you do not damage the GPS during the process. 1 Put the cross back on the drone. 4 With a box cutter, peel off the sticker. x6 1 Remove the 2 screws holding the nose. 2 Secure the nose with the 2 screws. 2 Disconnect the GPS from the flex. 1 Connect the GPS to the flex. 2 Remove the camera support and all its elements. 2 Put the lock on top of the connector. Make sure the screw holes are aligned. G207 G207 1 REMOVING THE NOSE 14 INSTALLING THE NOSE 2 REMOVING THE GPS 13 INSTALLING THE GPS 3 REMOVING THE CAMERA 12 INSTALLING THE CAMERA 1 Remove the 2 MCFAS00197 and the 2 MCFAS00221 screws. 1 Fix the connector of the camera support on the motherboard. 1 Remove the 3 screws holding the GPS to the support of the camera. 2 Secure the GPS with 3 new MCFAS00220 screws. 1 Remove the 4 screws holding the foot and remove the old foot. 1 Connect the cables to each connector. 3 Remove cable from the antenna. 3 Fix the antenna back to the cable. 2 Slide the antenna off the foot. 2 Secure each connector with 2 MCFAS00333 screws. 5 Disconnect the antennas of the front feet. 5 Put each foot back into place and secure them with 4 screws. 4 10 REMOVING THE FRONT FEET INSTALLING THE FRONT FEET 5 11 REMOVING THE REAR FEET INSTALLING THE REAR FEET REMOVING THE CAMERA AND THE FAN UNDER THE DRONE 1 Use a T5 screwdriver to remove the 4 screws holding the foot. 1 Connect the cables to each connector. 1 Use the pliers to remove the metal stems of the old motherboard. 5 Disconnect the cables of the fan and remove it completely. 4 Slightly pull on the cable to disconnect them from each connector. 4 Slide the antenna in the foot. 2 Remove the foot and use a T6 screwdriver to remove the 2 screws holding the connector. 2 Secure each connector with 2 MCFAS00333 screws. 2 Use a T5 screwdriver to remove the 3 screws holding the fan. 6 Disconnect the connector of the camera and remove it completely. 3 Slightly pull on the cable to disconnect it from the connector. 3 Put each foot back into place and secure them with 4 screws. 3 Use a T5 screwdriver to remove the 2 screws holding the camera. 2 Connect the fan to the motherboard. 5 Secure the fan with the 3 MCFAS00197 screws. 6 Use the pliers to screw the metal stems on the new motherboard. 3 With a box cutter, peel off the sticker. Put the sticker back into place. 1 Use a T5 screwdriver to remove the 2 screws holding the camera. 4 Secure the camera with the 2 MCFAS00199 screws. A A C C A A C C 1 Use the pliers to unscrew the 4 washers under the drone. 3 Secure the cross with the washers. 2 Make sure to correctly put back all the cables. 2 Remove the cross. REMOVING THE CROSS INSTALLING THE CROSS 6 9 7 Package content: 1 central body / 6 screws INSTALLING THE ELEMENTS ON THE NEW CENTRAL BODY 8 * Using a new nose part will ease the process and prevent from damaging the GPS. DIFFICULTY LEVEL