AEP ModelUK Model
SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
SPECIFICATIONS
Level 1
Continued on next page
C MECHANISM
DCR-VX2000ERMT-811
Ver 1.0 2000. 04
2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270Cduring repairing.
Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
Be careful not to apply force on the conductor when solderingor unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
3
Checking supplied accessories.
Check that the following accessories are supplied with your camcorder.
Wireless Remote Commander (1)RMT-8111-475-950-21
AC-L10 power adaptor (1)0 1-475-599-11Power cord set (1) (AEP only)0 1-690-827-11Power cord (with filter) (1) (UK only)0 1-775-843-21
NP-F330battery pack (1)A-7094-141-A
Size AA (R6) battery forRemote Commander (2)(not supplied)
A/V connecting cable(1.5m) (1)1-575-337-11
21-pin adaptor (1)1-573-291-11
Hood cap (1)X-3950-568-1
Other accessories3-060-458-11 MANUAL, INSTRUCTION
(PICTURE GEAR 4.1 LITE)(ENGLISH/RUSSIAN)3-060-458-21 MANUAL, INSTRUCTION
(PICTURE GEAR 4.1 LITE)(FRENCH/GERMAN)(AEP)3-060-458-31 MANUAL, INSTRUCTION
(PICTURE GEAR 4.1 LITE)(ITALIAN/DUTCH)(AEP)3-060-458-41 MANUAL, INSTRUCTION
(PICTURE GEAR 4.1 LITE)(SPANISH/PORTUGUESE)(AEP)
Application software:Picture Gear 4.1Lite(System Disc)(CD ROM) (1)3-060-476-01
Fig AMemory Stick Reader/Writer (1)(MSAC-US1) (1)A-7096-180-AFig BUSB cable (1)1-790-774-11
Memory Stick (1)(MSA-4A)A-7033-740-A
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Lens hood (1)X-3950-590-1
Shoulder strap (1)3-987-015-01
3-061-238-21 MANUAL, INSTRUCTION (MSAC-US1)(GERMAN/SPANISH/DUTCH/SWEDISH/ITALIAN/PORTUGUESE/
RUSSIAN/ARABIC/TRADITIONAL CHINESE/KOREAN/DANISH/FINNISH)(AEP)
3-061-508-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN)(AEP,UK)3-061-508-21 MANUAL, INSTRUCTION (GERMAN/ITALIAN)(AEP)3-061-508-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE)
(AEP)3-061-508-41 MANUAL, INSTRUCTION (FRENCH/DUTCH)(AEP)
Eyecup (large) (1)3-060-676-01
Fig A Fig B
4
TABLE OF CONTENTSSERVICE NOTE1. POWER SUPPLY DURING REPAIRS 52. TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) 5
SELF-DIAGNOSIS FUNCTION1. SELF-DIAGNOSIS FUNCTION 62. SELF-DIAGNOSIS DISPLAY 63. SERVICE MODE DISPLAY 63-1. Display Method 63-2. Switching of Backup No. 63-3. End of Display 64. SELF-DIAGNOSIS CODE TABLE 7
1. MAIN PARTS1. ORNAMENTAL PARTS 82. DISASSEMBLY 92-1. LCD SECTION (HL-011, PD-126 BOARDS,
INVERTER TRANSFORMER UNIT) 102-2. EVF SECTION (LB-065 BOARD) 112-3. (UPPER) HANDLE BLOCK ASSEMBLY 112-4. FK-076, MA-386, MI-038, FT-090 BOARDS 122-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM
DECK (FOR FORCE EJECT OF CASSETTE) 132-6. CABINET (R) BLOCK ASSEMBLY 142-7. CABINET BOTTOM (D) ASSEMBLY 142-8. BATTERY PANEL BLOCK ASSEMBLY
(MK-014, KP-010, MS-049 BOARDS) 152-9. EVF BLOCK ASSEMBLY 152-10. LA-026, DD-138, VC-242, JK-190 BOARDS,
MECHANISM DECK 162-11. LENS BLOCK ASSEMBLY, CENTER FRAME
ASSEMBLY 172-12. PRISM COVER ASSEMBLY 172-13. CONTROL SWITCH BLOCK (PS-4980),
CONTROL SWITCH BLOCK (CF-4980) 182-14. CK-093 BOARD 182-15. CONTROL SWITCH BLOCK (ED-4980),
HINGE ASSEMBLY 193. REPAIR PARTS LIST 203-1. EXPLODED VIEWS 203-1-1.OVERALL SECTION-1 203-1-2.OVERALL SECTION-2 213-1-3.CABINET (L) SECTION 223-1-4.CABINET (R) SECTION-1 233-1-5.CABINET (R) SECTION-2 243-1-6.UPPER HANDLE SECTION 253-1-7.BATTERY PANEL SECTION 263-1-8.EVF SECTION 273-1-9.CENTER FRAME SECTION 283-1-10. LENS BLOCK SECTION 29
2. GENERALChecking supplied accessories 30Quick Start Guide 30Getting started 31
Using this manual 31Step 1 Preparing the power supply 31Step 2 Inserting a cassette 33
Recording Basics 34Recording a picture 34 Shooting backlit subjects (BACK LIGHT) 36 Using the spot light function 36 Self-timer recording 37 Checking the recording END SEARCH/ EDIT SEARCH/Rec Review 37
Playback Basics 38Playing back a tape 38
Viewing the recording on TV 39Advanced Recording Operations 40
Recording a still image on a tape Tape Photo recording 40Shooting with all the pixels PROG. SCAN 41Using the guide frame 41Using the wide mode 41Using the fader function 42Using special effects Picture effect 42Using special effects Digital effect 43Shooting with manual adjustment 43Adjusting the white balance 46Adjusting recording level manually Sound recording level 46Presetting the adjustment for picture quality Custom preset 47Using the PROGRAM AE function 47Focusing manually 48Interval recording 49Frame by frame recording Cut recording 50Marking an Index 50
Advanced Playback Operations 51Quickly locating a scene using the zero set memory function 51Searching for a recording by index Index search 51Searching the boundaries of recorded tape by titleTitle search 52Searching a recording by date Date search 52Searching for a photo Photo search/Photo scan 53Playing back a tape with picture effects 54Playing back a tape with digital effects 54
Editing 54Dubbing a tape 54Dubbing only desired scenes Digital program editing 55Using with analog video unit and a PC Signal convert function 60Recording video or TV programs 60Inserting a scene from a VCR Insert editing 61Audio dubbing 62Superimposing a title 63Making your own titles 65Labeling a cassette 65Erasing the cassette memory data 66
Customizing Your Camcorder 67Changing the menu settings 67Resetting the date and time 69
Memory Stick Operations 69Using a Memory Stick introduction 69Recording still images on a Memory SticksMemory Photo recording 71Superimposing a still picture in a Memory Stickon a moving picture MEMORY MIX 72Recording an image from a mini DV tape as a still image 73Copying still images from a mini DV tape Photo save 74Viewing a still picture Memory photo playback 75Copying an image recorded on a Memory Sticks tomini DV tapes 76Playing back images continuously SLIDE SHOW77Preventing accidental erasure Image protection 77Deleting images 78Writing a print mark Print mark 79
Additional Information 79Usable cassettes 79About i.LINK 80Troubleshooting 81Self-diagnosis display 82Warning indicators and messages 82Using your camcorder abroad 83Maintenance information and precautions 83
Quick Reference 85Identifying the parts and controls 85Quick Function Guide 88
5
SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off sothat the unit cannot operate.These following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the ADJ side.
Method 2.Use the DC IN terminal. (Use the AC power adaptor. (AC-L10, AC-VQ800 etc. ))
2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)1 Refer to 2-3. to remove the upper handle block assembly.2 Refer to 2-5. to remove the cabinet (L) assembly.3 Refer to 2-5. to remove the mechanism deck (Including VC-242 board and DD-138 board).4 Remove DD-138 board from the mechanism deck (Including VC-242 board).5 Remove the CN022 (27P 0.3 mm) of VC-242 board.6 Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
Loading motor
DC power supply (+4.5V)
Disconnect from CN022 (27P)of VC-242 board.
: loading : unloading
6
SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTIONWhen problems occur while the unit is operating, the self-diagnosisfunction starts working, and displays on the viewfinder, LCD screenor LCD window what to do. This function consists of two display;self-diagnosis display and service mode display.Details of the self-diagnosis functions are provided in the Instructionmanual.
Note: The self-diagnosis display data will be backed up by the coin-type lithium battery of CK-093 board BT250. When CK-093 board is removed,the self-diagnosis display data will be lost by initialization.
2. SELF-DIAGNOSIS DISPLAYWhen problems occur while the unit is operating, the counter of theviewfinder, LCD screen or LCD window consists of an alphabetand 4-digit numbers, which blinks at 3.2 Hz. This 5-character displayindicates the repaired by:, block in which the problem occurred,and detailed code of the problem.
3. SERVICE MODE DISPLAYThe service mode display shows up to six self-diagnosis codes shown in the past.
3-1. Display MethodWhile pressing the STOP key, set the switch from OFF to VCR or PLAYER, and continue pressing the STOP key for 5 secondscontinuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
3-2. Switching of Backup No.By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which theproblem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)[1] : Occurred first time [4] : Occurred fourth time[2] : Occurred second time [5] : Occurred fifth time[3] : Occurred third time [6] : Occurred the last time
3-3. End of DisplayTurning OFF the power supply will end the service mode display.
Order of previous errors
Backup No. Self-diagnosis Codes
C : 3 1 : 1 1[3]
Lights up
Viewfinder or LCD screen
[3] C : 3 1 : 1 1 3 C : 3 1 : 11LCD window
1 13 1
C : 3 1 : 11
C
Repaired by:
Refer to page 7.Self-diagnosis Code Table.
Indicates the appropriatestep to be taken.E.g.31 ....Reload the tape.32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2Hz
C : Corrected by customerH : Corrected by dealerE : Corrected by service
engineer
Viewfinder or LCD screen LCD window
C : 3 1 : 1 1
Control dial
7
4. SELF-DIAGNOSIS CODE TABLE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
BlockFunction
0 4
2 1
2 2
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
6 1
6 1
6 2
6 2
DetailedCode
0 0
0 0
0 0
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
0 0
1 0
0 0
0 1
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does notcomplete within specified time
UNLOAD direction. Loading does notcomplete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-out.
UNLOAD direction loading motortime-out.
T reel side tape slacking whenunloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drumoperations
Difficult to adjust focus(Cannot initialize focus.)
Zoom operations fault(Cannot initialize zoom lens.)
Steadyshot function does not work well.(With pitch angular velocity sensor outputstopped.)
Steadyshot function does not work well.(With yaw angular velocity sensor outputstopped.)
Self-diagnosis Code
Rep
aire
d by
:
Correction
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Inspect the lens block focus reset sensor (Pin wg of LA-026 board)when focusing is performed when the control dial is rotated in thefocus manual mode, and the focus motor drive circuit (IC140 ofLA-026 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin ws of LA-026 board)when zooming is performed when the zoom lens is operated andthe zoom motor drive circuit (IC140 of LA-026 board) whenzooming is not performed.
Inspect pitch angular velocity sensor (SE601 or SE602 of SE-108board) peripheral circuits.
Inspect yaw angular velocity sensor (SE600 or SE603 of SE-108board) peripheral circuits.
8
1. MAIN PARTS
Note: Follow the disassembly procedure in the numerical order given. Items marked * are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items. The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
1. ORNAMENTAL PARTS
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
DCR-VX2000E
Remote commander (RMT-811)1-475-950-21
Battery case lid (for RMT-811)3-053-056-01
Eye cup3-060-573-01
Spring bolt (M2)3-053-121-41
CPC cover3-060-677-01
Hood cap assemblyX-3950-568-1
Lens hood assemblyX-3950-590-1
Jack cover (AV)3-060-540-01
Jack cover (L)3-060-541-01
9
2. DISASSEMBLYThe following flow chart shows the disassembly procedure.
DC
R-V
X20
00E
2-2. EVF section (LB-065 board)
2-5. Cabinet (L) block assembly, Mechanism deck (For force eject of cassette)
2-4. FK-076, MA-386, MI-038, FT-090 boards
2-13. Control switch block (PS-4980), Control switch block (CF-4980)
2-12. Prism cover assembly
2-1. LCD section (HL-011, PD-126 boards, Inverter transformer unit)
2-3. (Upper) handle block assembly
2-6. Cabinet (R) block assembly
2-7. Cabinet bottom (D) assembly
2-14. CK-093 board
2-15. Control switch block (ED-4980), Hinge assembly
2-8. Battery panel block assembly (MK-014, KP-010, MS-049 boards)
2-9. EVF block assembly
2-10. LA-026, DD-138, VC-242, JK-190 boards, Mechanism deck
2-11. Lens block assembly, Center frame assembly
10
2-1. LCD SECTION (HL-011, PD-126 BOARDS, INVERTER TRANSFORMER UNIT)
NOTE: Follow the disassembly procedure in the numerical order given.
PD-12
6
Board
PD-12
6
Board
A
B
1 Two screws (M2 5), spring bolt
qs Two screws (M2 3), spring bolt
2 Two screws (M2 3), spring bolt
2 Two screws (M2 5), spring bolt
qa Screw (M2 3), spring bolt
4 FP-195 flexible board (7P)
5 FP-196 flexible board (5P)
6 FP-205 flexible board (21P)
8 Indication panel block assembly
qd Panel holder7 Release the two claws and slide the indication panel block assembly in the direction of the arrow A.
9 Release the two claws and slide the HL-011 board in the direction of the arrow B.
q; HL-011 board
qg PD-126 board, Inverter transformer unit
qf PCB clip
qa Two claws
qd PCB clip
3 P cabinet (C) assembly
5 Harness (CP-094) (14P)
6 LCD frame, BL retainer, FP-196 flexible board
1 FP-195 flexible board (7P)
4 Harness (CP-093) (8P)
q; Screw (M1.7 2.5), lock ace
7 Two screws (M1.7 2.5), lock ace
qs Back light Cold cathode fluorescent tube
9 Liquid crystal indicator module (24P)
8 P cabinet (M) assembly
3 Three claws
11
2-2. EVF SECTION (LB-065 BOARD)
2-3. (UPPER) HANDLE BLOCK ASSEMBLY
A
B1 Push the lock knob in the direction of the arrow A and remove the EVF rear cabinet assembly in the direction of the arrow B.
2 EVF rear cabinet assembly
4 EVF front cabinet (upper)
6
5 EVF front cabinet (lower) assembly
3 Two tapping screws (M1.7 8)
3 Two claws
4 LB-065 board5 LCD cushion (498)6 Illuminator (498)7 LCD cushion (498)
9 Light interception sheet
q; LCD holder assembly
REMOVING THE LB-065 BOARD
1 FP-193 flexible board (27P)
2 LCD (LCX033AK-J)(16P)8 LCD (LCX033AK-J)
1 Two screws (M2 5), spring bolt
2 Two screws (M2 5), spring bolt
3 Screw (M2 5), spring bolt
5 Screw (M2 5), spring bolt
4 Tilt up the finder.6 Tilt down the finder.
7
9 (Upper) handle block assembly
8 FP-200 flexible board (36P)
12
2-4. FK-076, MA-386, MI-038, FT-090 BOARDS
1 FP-202 flexible board (27P)
9 FP-201 flexible board (15P)
qs FP-199 flexible board (15P)
wa FP-198 flexible board
ws M terminal protection sheet
qd Remove it in the direction of the arrow A.
A 4 FK frame (D) assembly
3 FK-076 board
2 Four screws (M2 3), spring bolt
5 Two screws (M2 5), spring bolt
qh Screw (M2 5), spring bolt
qf Microphon sheet
1 Two tapping screws (B2 5)
2 Tapping screw (B2 5)
4 Claw7 Four claws
8 Microphone unit
9 Microphone case
qa Microphone caseq; Microphone unit
5 Microphone cover
qs FP-199 flexible board, MI-038 board, FT-090 board
6 Microphone mask assembly
3 Rubber neck assembly
ql Nut (M6 0.5)
qg Screw (M2 3), spring bolt
qk Handle assembly, (Upper) cabinet
wd MA-386 board
qj Screw (M2 5), spring bolt
w; Screw (M2 3), spring bolt
q; Two screws (M2 3), spring bolt
qa Outer connector (hot shoe), Strap sheet metal (F), FP-201 flexible board
7 Screw (M2 5), spring bolt
8 Microphone cabinet (L)
wf Microphone cabinet (R) assembly
6 Handle cover assembly
REMOVING THE MI-038, FT-090 BOARDS
13
2-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM DECK (FOR FORCE EJECT OF CASSETTE)
1 Screw (M2 5), spring bolt
6 Cabinet (L) block assembly
2 Screw (M2 5), spring bolt
3 Screw (M2 5), spring bolt
4 Two screws (M2 3), spring bolt
9 Four screws (M2 3), spring bolt
4 Screw (M2 3), spring bolt
3 Screw (M2 3), spring bolt
5 Flexible retainer
1 FP-193 flexible board (27P)
7 FP-186 flexible board (80P)
qa CD-254 board (50P)
qs Battery terminal board (4P)
qd DC-IN connector (3P)qf Mechanism deck, VC-242, DD-138 board, MD frame assembly
2 FP-200 flexible board (10P)
6 FP-187 flexible board (50P)
8 JK-190 board (40P)
q; Claw
5 Three screws (M2 5), spring bolt
(FOR FORCE EJECT OF CASSETTE)
14
2-6. CABINET (R) BLOCK ASSEMBLY
1 Screw (M2 5), spring bolt
5 Screw (M2 5), spring bolt
4 Two screws (M2 5), spring bolt
6 Two screws (M2 5), spring bolt
7 Cabinet (R) block assembly
3 CF ornamental plate
2 Claw
2-7. CABINET BOTTOM (D) ASSEMBLY
2 Four screws (M2 5), spring bolt
4 Two screws (M2 5), spring bolt
1 Two tapping screws (B2 5)
3 Two tapping screws (B2 5)
5 FBS cover assembly
4 Cabinet (bottom)3 Tripod table
5 Cabinet bottom (D) assembly
1 FP-189 flexible board (6P)
2 FP-189 flexible board
REMOVING THE FBS COVER ASSEMBLY
15
2-8. BATTERY PANEL BLOCK ASSEMBLY (MK-014, KP-010, MS-049 BOARDS)
2-9. EVF BLOCK ASSEMBLY
LA-02
6
board
MS-04
9
Board
A
A
1 FP-190 flexible board (20P)
2 DC-IN connector (3P)
3 Battery terminal board (4P)
5 Screw (M2 5), spring bolt
8 Screw (M2 5), spring bolt
9 CPC coverq; Battery panel block assembly
4 Screw (M2 3), spring bolt
6 Two screws (M2 5), spring bolt
7 Two screws (M2 5), spring bolt
1 Two tapping screws (B2 5)
8 Two tapping screws (B2 5)
q; Two tapping screws (B2 5)
qa DC jack retainer
qs DC-IN connector
9 MS holder assembly
2 MK retainer
3 MK-014 board
When installing it,align the switch positionas shown.
5 KP-010 board
7 MS-049 board
4 Screw (M2 3), spring bolt
6 Two screws (M2 3), spring bolt
PRECAUTION DURINGINSTALLATION
LA-02
6
board
2 Screw (M2 3), spring bolt
6 Two screws (M2 3), spring bolt
7 EVF block assembly
3 Claw
5 Flexible clamp
4 Peel off the area shown by shading.
1 FP-193 flexible board (27P)
16
2-10. LA-026, DD-138, VC-242, JK-190 BOARDS, MECHANISM DECK
LA-02
6
Board
LA-026
Board
LA-02
6
Board
VC-24
2
Board
DD-
138
A
A
B
B
D
D
C
C
1 Screw (M2 3), spring bolt
8 Screw (M2 3), spring bolt
9 LA joint
2 Flexible retainer
6 Three screws (M2 3), spring bolt
2 Two screws (M2 3), spring bolt
1 Two screws (M2 3), spring bolt
qa Two screws (M2 3), spring bolt
qs Two screws (M2 3), spring bolt
qd Two claws
qf JK frame
qg JK-190 board
3 Three screws (M2 3), spring bolt
5 Two step screws (M2)
7 MD frame assembly
q; Mechanism deck
9 LD outer lid
6 Step screw (M2)
8 Two screws (M2 2), lock ace
2 DD-138 board
4 VC-242 board
3 Two screws (M2 3), spring bolt
4 Two screws (M2 5), spring bolt
5
7 LA-026 board
(LA-026 board)
3 FP-188 flexible board (6P)
4 Flexible board (39P) (from zoom lens assembly)
1 CD-254 board (50P)
5 Flexible board (27P) (from VAP assembly)
17
2-11. LENS BLOCK ASSEMBLY, CENTER FRAME ASSEMBLY
1 Screw (M2 3), spring bolt
q; Two screws (M2 4), lock aceqa Two screws (M2 3), spring bolt
qs FP-188 flexible board (6P)
FP-188 flexible board
qd Center frame assembly
Center frame assembly
6 Screw (M2 3), spring bolt
7 Two screws (M2 5), spring bolt
8 Two screws (M2 5), spring bolt
4 Screw (M2 3), spring bolt
5 CJ-064 harness
9 Lens block assembly
Lens block assembly
2 Tapping screw (B2 5)
3 CCD cover
When installing it.Align the swich position.
PRECAUTION DURING INSTALLATION
2-12. PRISM COVER ASSEMBLY
6 Sheet (CD)
5 Ornamental ring assembly
A
B
qa
9 CCD emblem
4 Name ring
q; Rubber foot (A)
1 CCD heat sink
Prism cover assembly
2 Prism tape
3 Prism cover
Rotate it in the direction ofthe arrow A and remove itin the direction of the arrow B.
7 Remove the soldering.
8 CJ-064 harness
18
2-13. CONTROL SWITCH BLOCK (PS-4980), CONTROL SWITCH BLOCK (CF-4980)
2-14. CK-093 BOARD
1 Tapping screw (B2 5)
4 Two tapping screws (B2 5)
7 Four tapping screws (B2 5)
9 Two tapping screws (B2 5)
8 Slider assembly
2 Control switch block (PS-4980) (8P)
q; Control switch block (CF-4980)
5 Control switch block (PS-4980)
3 Control switch block (CF-4980)
6 Push the eject knob in the direction of the arrow, and open the cassette lid.
Cassette lid
Eject knob
Eject lever
Be careful not to damagethe control switch block's(CF-4980) flexible.PRECAUTION DURING
INSTALLATIONInstall the slider assemblywhile pushing the eject leverfully to the left (CCW).
1 Control switch block (ED-4980) (6P)
2 FP-197 flexible board (6P)
9 FP-194 flexible board (5P)
3 R flexible protection sheet
5 Two screws (M2 3), spring bolt
q; Seven screws (M2 3), spring bolt
qa Claw
6 SP retainer plate assembly
4 Speaker (2P)7 Speaker
8 Speaker holder
qd Harness (CP-094) (14P)
qs Harness (CP-093) (8P)
qf CK-093 board
When installing it.Align the switch position.
PRECAUTION DURINGINSTALLATION
19
2-15. CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLYStart the removal work after the LCD section has been removed referring section 2-1.
A
Aqa FP-197 flexible board
8 Three screws (M2 5), spring bolt
1 Bright button
91 Three screws (M2 3), spring bolt
6 Three screws (M2 3), spring bolt
7
2 Hinge lid
5 Harness (CP-094) (14P)
4 Harness (CP-093) (8P)
8 Harness (CP-094)
7 Harness (CP-093)
3 Blind door (D) assembly
2 Control switch block (ED-4980)
1 Two screws (M1.7 2.5), lock ace
9 Screw (M1.7 2.5), lock ace
q; Screw (M1.7 2.5), lock ace
6 Two harness fixed tapes
5 Hinge cover (front)
qs Hinge assembly
4 Hinge cover (rear)
2 Screw (M1.7 2.5), lock ace3 Three claws
20
3. REPAIR PARTS LIST3-1. EXPLODED VIEWSNOTE: -XX, -X mean standardized parts, so they may
have some differences from the original one. Items marked * are not stocked since they
are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
The mechanical parts with no reference numberin the exploded views are not supplied.
3-1-1. OVERALL SECTION-1
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
1 1-678-055-21 FP-187 FLEXIBLE BOARD2 3-053-121-21 BOLT(M2), SPRING3 3-060-683-01 PLATE, CF ORNAMENTAL4 X-3950-595-1 BOTTOM (D) ASSY, CABINET5 X-3950-728-1 COVER ASSY, FBS (SERVICE)
6 3-948-339-61 TAPPING7 3-062-455-01 FOOT(B), RUBBER8 1-678-057-21 FP-189 FLEXIBLE BOARD
9 3-053-121-41 BOLT(M2), SPRING10 3-963-940-02 TABLE, TRIPOD11 X-3950-590-1 HOOD ASSY, LENS12 X-3950-568-1 CAP ASSY, HOOD13 3-053-121-31 BOLT(M2), SPRING
14 1-678-067-21 FP-200 FLEXIBLE BOARD15 1-475-950-21 REMOTE COMMANDER (RMT-811)16 3-053-056-01 LID,BATTERY CASE (FOR RMT-811)
A
A
B
B
1
2
4
5
6
7
8
910
1112
9
6
2 2
2
3
notsupplied
9
2
13
2
2
99
14
15
16
Upper handle section(See page 25)
Cabinet (L) section(See page 22)
Cabinet (R) section(See page 23, 24)
21
3-1-2. OVERALL SECTION-2
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 3-053-121-11 BOLT(M2), SPRING52 not supplied LA-026 BOARD, COMPLETE53 3-060-682-01 FRAME, JK54 not supplied JK-190 BOARD, COMPLETE
* 55 3-053-354-01 CUSHION, CD FLEXIBLE
56 3-060-673-01 LID,LD OUTER57 3-056-233-11 SCREW (M2), LOCK ACE, P258 3-060-684-01 JOINT, LA59 3-975-921-01 SHEET, VIBRATION PROOF60 3-061-679-01 SPRING, MD GROUND
61 3-060-789-01 RETAINER, FLEXIBLE62 X-3950-571-1 FRAME ASSY, MD
63 3-988-464-01 SCREW (M2), STEP64 not supplied VC-242 BOARD, COMPLETE (SERVICE)65 1-678-054-21 FP-186 FLEXIBLE BOARD66 3-061-053-01 SHEET, FP19167 1-678-059-21 FP-191 FLEXIBLE BOARD
68 3-061-516-01 SHEET, RF FLEXIBLE69 not supplied DD-138 BOARD, COMPLETE70 3-060-787-01 CLAMP, FLEXIBLE71 3-060-677-01 COVER, CPC72 3-053-121-41 BOLT(M2), SPRING
* 73 3-062-779-01 SHEET (VC)75 3-053-121-21 BOLT(M2), SPRING
LA-02
6
Board
VC-24
2
Board
DD-
138
A
A
E
B
B
DD
C C
E
J
F
F
G
GH
H
I
J
KIK
51
52
51
51
5151
51
51
51
51
5154
55
55
56
57 58
59
60
61
62
63
63
64
65
73
66
67
68 69 70
53
75
51
75
7172
72
72
Mechanism deck
EVF section(See page 27)
Battery panel section(See page 26)
22
3-1-3. CABINET (L) SECTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 X-3950-688-1 CABINET (L) ASSY102 3-703-357-08 PIN(DIA. 1.6 SERISE)103 3-060-550-01 BRACKET (REAR), GRIP104 3-948-339-01 SCREW, TAPPING105 X-3950-561-1 CS ASSY
106 3-051-871-01 BRACKET (FRONT), BELT107 3-060-540-01 COVER (AV), JACK108 X-3950-679-1 LID ASSY, CASSETTE109 3-060-790-01 SCREW (M2 STEP)110 3-060-548-01 BELT, GRIP
111 3-060-541-01 COVER (L), JACK112 3-060-551-01 KNOB, EJECT
113 3-060-549-01 SHEET, EJECT114 4-634-290-11 DAMPER115 3-060-554-01 SPRING, TENSION116 3-968-729-81 SCREW (M2), LOCK ACE, P2117 3-669-465-01 WASHER (1.5), STOPPER
118 3-060-553-01 LEVER, EJECT119 X-3950-585-1 SHEET METAL ASSY, EJECT120 X-3950-562-1 SLIDER ASSY121 3-948-339-61 TAPPING122 1-476-075-21 SWITCH BLOCK, CONTROL (PS-4980)
123 1-476-025-21 SWITCH BLOCK, CONTROL (CF-4980)
A
B
B
C
CD
E
F
F
E
A
D
notsupplied
notsupplied
notsupplied
101
102103
104
105
104
104
114116
104
104106
107
108
109
110
111
112113 115
117118
119
120
121
122
121
121
123
121
23
3-1-4. CABINET (R) SECTION-1
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
Note : The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
151 3-053-121-11 BOLT (M2), SPRING* 152 3-060-698-01 RETAINER, BL
153 1-678-063-21 FP-196 FLEXIBLE BOARD* 154 3-060-688-01 FRAME, LCD
155 3-061-509-01 PAD(RIGHT), PD
* 156 3-060-687-01 HOLDER, PANEL157 3-053-121-41 BOLT (M2), SPRING158 not supplied HL-011 BOARD, COMPLETE159 X-3950-689-1 CABINET (C) ASSY, P160 3-060-796-01 SHEET, R FLEXIBLE PROTECTION
* 161 X-3950-577-1 PLATE ASSY, SP RETAINER* 162 3-060-686-01 HOLDER, SPEAKER0163 not supplied TRANSFORMER UNIT, INVERTER
164 1-678-062-11 FP-195 FLEXIBLE BOARD* 165 3-051-232-01 CLIP, PCB
166 not supplied PD-126 BOARD, COMPLETE (SERVICE)167 3-989-735-11 SCREW (M1.7), LOCK ACE, P2168 X-3950-597-1 CABINET (M) ASSY, P
169 3-060-704-01 SHEET (N), BL SHIELD170 3-061-510-01 PAD(UPPER), PD
* 171 3-062-196-01 SHEET, BL INSULATINGLCD901 not supplied ACX300CK-JLCD902 not supplied PANEL BLOCK ASSY, INDICATION
0ND901 not supplied TUBE, FLUORESCENT,COLD CATHODESP901 1-529-590-11 SPEAKER (2.0CM)
PD-126Board
A
B
C
C
D
D
B
A
notsupplied
SP901
LCD902
ND901
LCD901
151
152
153
154
160
161
162
163164
165166
167167
168 157
157
169
170
155
165
156151
158
159
151
151
151
151
171
Cabinet (R) section-2(See page 24)
24
3-1-5. CABINET (R) SECTION-2
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
201 X-3950-599-1 DOOR (D) ASSY, BLIND202 3-060-795-01 TAPE, HARNESS FIXED203 1-960-558-11 HARNESS (CP-094) 14P204 1-960-557-11 HARNESS (CP-093) 8P205 1-476-183-11 SWITCH BLOCK, CONTROL (ED-4980)
206 3-060-689-01 BUTTON, BRIGHT207 3-053-121-21 BOLT (M2), SPRING208 3-989-735-11 SCREW (M1.7), LOCK ACE, P2209 3-060-693-01 COVER (FRONT), HINGE210 X-3950-576-1 HINGE ASSY
211 3-060-694-11 COVER (REAR), HINGE212 1-678-064-21 FP-197 FLEXIBLE BOARD213 3-053-121-11 BOLT (M2), SPRING
* 214 3-060-690-01 LID, HINGE215 not supplied CK-093 BOARD, COMPLETE
216 X-3950-682-1 CABINET (R) ASSY* 217 3-060-640-01 COVER, ZEBRA KNOB
218 3-060-644-01 KNOB, ZEBRA
219 3-060-636-01 BUTTON, R220 3-060-637-01 GRILLE, SPEAKER221 3-060-639-01 SHEET, PROTECTION222 3-052-521-01 CUSHION (2), PANEL223 3-989-735-01 SCREW (M1.7), LOCK ACE, P2
224 3-060-630-01 BASE, PANEL LOCK225 3-060-641-01 PAD, PANEL (POP) UP226 3-060-632-01 UP, PANEL (POP)227 3-060-633-01 SPRING, COMPRESSION228 3-060-638-01 KNOB, PANEL LOCK
229 3-060-643-01 CLAW, PANEL LOCK230 3-060-634-01 SPRING, PANEL LOCK231 3-060-635-01 SHAFT, PANEL LOCK232 3-060-642-01 BUTTON, MENU
* 233 3-060-691-01 BRACKET, MENU BUTTON
234 1-678-061-21 FP-194 FLEXIBLE BOARD* 235 3-060-631-01 BRACKET, PANEL LOCK
CK-09
3
Board
A
A
B
B
C
C
D
D
not supplied
not supplied
201
202203
204
205
206
207
207
223209
210
211
212
213
213
213
208
208
208213
216
217
218 219
214 215
213
213 213
213220
221222
223
224
225226
227
228
229230231
232
233
235
234
213
213
: BT250 (Lithium battary) CK board on the mount position.
25
3-1-6. UPPER HANDLE SECTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
251 3-963-968-01 CASE, MICROPHONE252 3-948-339-01 SCREW, TAPPING253 X-3950-579-1 MASK ASSY, MICROPHONE254 not supplied FT-090 BOARD, COMPLETE255 not supplied MI-O38 BOARD, COMPLETE
256 1-678-066-11 FP-199 FLEXIBLE BOARD257 3-060-706-01 COVER, MICROPHONE258 X-3945-076-1 NECK ASSY, RUBBER259 1-785-594-11 CONNECTOR (HOT SHOE), OUTER260 X-3950-582-1 COVER ASSY, HANDLE
261 3-053-121-41 BOLT (M2), SPRING262 3-053-121-11 BOLT (M2), SPRING263 not supplied MA-386 BOARD, COMPLETE264 3-060-709-01 SHEET METAL (F), STRAP265 3-989-735-11 SCREW (M1.7), LOCK ACE, P2
266 1-678-068-11 FP-201 FLEXIBLE BOARD267 1-678-049-11 FP-202 FLEXIBLE BOARD
268 X-3950-685-1 HANDLE ASSY269 3-060-786-11 CABINET (UPPER)270 3-053-121-21 BOLT (M2), SPRING271 X-3950-600-1 FRAME (D) ASSY, FK272 not supplied FK-076 BOARD, COMPLETE
273 3-060-708-01 CABINET (L), MICROPHONE274 1-678-065-21 FP-198 FLEXIBLE BOARD275 X-3950-684-1 CABINET (R) ASSY, MICROPHONE276 3-061-234-01 NUT(M6X0.5)277 3-060-707-01 COVER, MJ
* 278 3-061-544-01 SHEET, MICROPHONE* 279 3-061-626-01 SHEET, MA SHIELD* 280 3-061-511-01 SPACER, MICROPHONE* 282 3-062-543-01 CUSHION, MA FLEXIBLE
MIC901 1-542-263-11 MICROPHONE UNIT
MIC902 1-542-263-11 MICROPHONE UNIT
C
C
A
B
A
B
251
251
252
252
253
254
255256
257258
259
260
261
262
263
282264
265
266
279
267
268269
270
271
272
262
273
262
261
MIC901
MIC902
261
261
262274280
275
276
277
notsupplied
notsupplied
278
26
3-1-7. BATTERY PANEL SECTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
301 not supplied MK-014 BOARD, COMPLETE* 302 3-060-678-01 RETAINER, MK
303 3-948-339-61 TAPPING* 304 3-060-679-01 HOLDER, KP
305 not supplied KP-010 BOARD, COMPLETE
306 3-053-121-11 BOLT (M2), SPRING307 1-678-058-11 FP-190 FLEXIBLE BOARD308 not supplied MS-049 BOARD, COMPLETE309 X-3950-589-1 HOLDER ASSY, MS310 1-694-411-11 TERMINAL BOARD, BATTERY
* 311 3-060-680-01 RETAINER, DC JACK
312 1-794-637-11 CONNECTOR, DC-IN313 X-3950-680-1 PANEL ASSY, BATTERY314 3-060-592-01 BRACKET (R), S BELT315 3-060-595-01 CLAW, BT LOCK316 3-060-594-01 LEVER, BT RELEASE
317 3-053-121-41 BOLT (M2), SPRING* 318 3-060-774-01 JOINT, BT-R
319 3-060-598-01 BUTTON, AL320 3-060-776-01 SHEET, AL321 3-060-773-01 COVER, DC JACK
MS-04
9
Board
MK
-014
not supplied
notsupplied
notsupplied
not supplied
not supplied
301
302303
303
303
303303319
320
321
303
311312
313
314
315
316
317 318
304
305
306
307
309
310
308 306
27
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
not supplied
LCD903 351
352
353
354
355
356
357358
358
360
359
361
362
351 X-3950-563-1 CABINET ASSY, EVF REAR352 3-060-573-01 CUP, EYE353 X-3950-564-1 CABINET (LOWER) ASSY, EVF FRONT354 X-3950-565-1 HINGE ASSY, VF355 3-713-791-21 SCREW (M1.7X8), TAPPING, P2
356 1-678-060-11 FP-193 FLEXIBLE BOARD357 not supplied LB-065 BOARD, COMPLETE
358 3-060-702-01 CUSHION (498), LCD359 3-060-701-01 ILLUMINATOR (498)360 3-060-788-01 SHEET, LIGHT INTERCEPTION361 X-3950-584-1 HOLDER ASSY, LCD362 3-060-674-01 CABINET (UPPER), EVF FRONT
LCD903 not supplied LCX033AK-J
3-1-8. EVF SECTION
28
not supplied
not supplied
402403
404
405
406
407
407
414407
408
409
410
401
411407 413
407
412
412
Lens block section(See page 29)
401 X-3950-681-1 FRAME ASSY, CENTER402 3-060-620-01 BUTTON, IP403 3-060-621-01 ESCUTCHEON404 3-060-622-01 KNOB, MF405 3-060-619-01 KNOB, ND
406 3-060-623-01 COVER, BUTTON407 3-053-121-11 BOLT (M2), SPRING
408 1-678-056-21 FP-188 FLEXIBLE BOARD409 3-060-685-01 COVER, CCD410 3-948-339-61 TAPPING411 3-053-121-21 BOLT (M2), SPRING412 3-060-795-01 TAPE, HARNESS FIXED
413 1-960-654-11 HARNESS, CJ-064414 3-968-729-91 SCREW (M2), LOCK ACE, P2
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
3-1-9. CENTER FRAME SECTION
29
451 X-3950-586-1 COVER ASSY, PRISM452 not supplied CD-254 BOARD, COMPLETE453 3-713-791-61 SCREW (M1.7X7), TAPPING, P2454 not supplied PRISM ASSY (SERVICE)(INCLUDE 3CCD)455 3-948-339-61 TAPPING
456 not supplied SE-108 BOARD, COMPLETE457 3-948-339-31 SCREW, TAPPING P2458 not supplied LENS ASSY, ZOOM
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
not supplied
451
452465
466
453
457458
460
461
462463464
459
454
455
456
459 3-713-791-91 SCREW (M1.7)460 not supplied VAP ASSY (B114A)461 3-709-594-01 RING ASSY, ORNAMENTAL462 3-963-933-01 EMBLEM, CCD463 3-062-454-01 FOOT (A), RUBBER
464 3-060-681-01 RING, NAME* 465 3-053-354-01 CUSHION, CD FLEXIBLE* 466 3-062-778-01 SHEET (CD)
3-1-10. LENS BLOCK SECTION
30
This section is extractedfrom instruction manual.
DCR-VX2000E2. GENERAL
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
DCR-VX2000E
Sony CorporationPersonal VIDEO Products Company 2000D1620-1Printed in Japan 2000.4
Published by Safety & Service Engineering Dept.
9-929-821-41