Sony HVR A1service Manual

HVR-A1J/A1U/A1N/A1E/A1P/A1C RMT-831SERVICE MANUALVer 1.1 2005.11Revision History How to use Acrobat Reader

US Model Canadian Model AEP Model E Model Chinese Model Japanese Model

N MECHANISM (MDX-N101)

LinkSPECIFICATIONS MODEL INFORMATION TABLE SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST ADJUSTMENT INSTRUCTION MANUAL

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

DIGITAL HD VIDEO CAMERA RECORDERHVR-A1J/A1U/A1N/A1E/A1P/A1C9-876-892-112005K0500-1 2005.11 Published by DI Technical Support Department

Sony EMCS Co.

These specifications are extracted from instruction manual of HVR-A1U/A1N.

ENGLISH

JAPANESE

SPECIFICATIONSSystemVideo recording system (HDV) Video recording system (DVCAM (DV)) Still image recording system Audio recording system (HDV) Audio recording system (DVCAM (DV)) Video signal Usable cassette 2 rotary heads, Helical scanning system 2 rotary heads, Helical scanning system Exif Ver. 2.2*1 Rotary heads, MPEG-1 Audio Layer -2, Quantization: 16 bits (Fs 48 kHz, stereo) transfer rate: 384 kbps Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) NTSC color, EIA standards 1080/60i specification Mini DV cassette with the or Mini DVCAM cassette with the mark printed Approx. 18.812 mm/s Approx. 28.218 mm/s Approx. 18.812 mm/s 63 min (using a PHDVM-63 DM cassette) 41 min (using a PHDVM-63 DM cassette) 63 min (using a PHDVM-63 DM cassette) Approx. 2 min 40 s (using a PHDVM-63 DM cassette and rechargeable battery pack) Approx. 1 min 45 s (using a PHDVM-63 DM cassette and AC Adaptor) Electric viewfinder (color, black and white) 5.9 mm (1/3 type) CMOS sensor Gross: Approx. 2 969 000 pixels Effective (movie, 4:3): 1 486 000 pixels Effective (movie, 16:9): 1 983 000 pixels Effective (still, 4:3): 2 764 800 pixels Effective (still, 16:9): 2 073 600 pixels Carl Zeiss Vario-Sonnar T* 10 (Optical), 40 (Digital) f=5.1 ~ 51.0 mm (7/32 ~ 2 1/8 in.) When converted to a 35 mm still camera In CAMERA-TAPE *2 : 41 ~ 480 mm (1 5/8 ~ 19 in.) (16:9), 50 ~ 590 mm (2 ~ 23 1/4 in.) (4:3) In CAMERA-TAPE when setting [FULL SCAN] to [ON]: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), 49.3 ~ 493 mm (2 ~ 19 1/2 in.) (4:3) In CAMERA-MEMORY: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (16:9), COMPONENT OUT jack 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) (4:3) F1.8 ~ 2.1 Filter diameter: 37 mm (1 1/2 in.) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K) Minimum 7 1x (lux) (F 1.8) illumination 0 lx (lux) (during NightShot function)*3 *1 Exif is a file format for still images, established by the JEITA (Japan Electronics and Information Technology Industries Association). Files in this format can have additional information such as your camcorders setting information at the time of recording. 2 The focal length figures are actual figures * resulting from wide angle pixel read-out. *3 Objects unable to be seen due to the dark can be shot with infrared lighting. Operating temperature Storage temperature Dimensions (approx.) Mass (approx.) 0 C to 40 C (32 F to 104 F) -20 C to + 60 C (-4 F to + 140 F) 71 103 191 mm (2 7/8 4 1/8 7 5/8 in.) (w/h/d) excluding the projecting parts 670 g (1 lb 7 oz) main unit only 1.1 kg (2 lb 8 oz) including the NP-FM50 rechargeable battery pack, PHDVM-63DM cassette, lens hood with lens cover, XLR adaptor and microphone. Memory Stick Duo 16MB (1) Memory Stick Duo Adaptor (1) AC Adaptor (1) Power cord (1) Lens hood with lens cover (1) Wireless Remote Commander (1) A/V connecting cable (1) Component video cable (1) USB cable (1) Shoulder Strap (1) XLR adaptor (1) Wind Screen (1) Microphone (1) Rechargeable battery pack NP-FM50 (1) Operating Guide (1) See page 5-40.

Supplied accessories

Tape speed (HDV) Tape speed (DVCAM) Tape speed (DVSP) Recording/ playback time (HDV) Recording/ playback time (DVCAM) Recording/ playback time (DV SP) Fast forward/ rewind time

Output connectorsAudio /Video output 10-pin connector Video signal: 1 Vp-p, 75 (ohms), unbalanced Luminance signal: 1 Vp-p, 75 (ohms), unbalanced Chrominance signal: 327 mV (at load impedance 47 k (kilohms)), Output impedance with less than 2.2 k (kilohms) Y:1 Vp-p, 75 (ohms), unbalanced PB/PR, CB/CR: 525 mVp-p (75 % color-bar) Stereo minijack ( 3.5)

AC Adaptor AC-L15APower requirements Current consumption Power consumption Output voltage Operating temperature Storage temperature Dimensions (approx.) AC 100 - 240 V, 50/60 Hz 0.35 - 0.18 A 18 W DC 8.4 V* 0 C to 40 C (32 F to 104 F) -20 C to + 60 C (-4 F to + 140 F) 56 31 100 mm (2 1/4 1 1/4 4 in.) (w/h/d) excluding the projecting parts 190 g (6.7 oz) main unit only

Headphones jack

Input/Output connectorsMIC jack Minijack, 0.388 mV low impedance with DC 2.5 to 3.0 V, output impedance 6.8 k (kilohms) ( 3.5 mm), Stereo type LANC jack Stereo mini-minijack ( 2.5) INPUT1/ XLR3-pin, female, INPUT2 -60 dBu:3 k connectors +4 dBu:10 k (0 dBu=0.775 Vrms) USB jack mini-B HDV/DV jack i.LINK Interface (IEEE 1394, 4-pin connector S100)

Viewfinder Image device

Mass (approx.)

LCD screenPicture Total dot number 6.9 cm (2.7 type, aspect ratio 16:9) 123 200 (560 220)

* See the label on the AC Adaptor for other specifications.

Rechargeable battery pack (NP-FM50)Maximum output voltage Output voltage Capacity Dimensions (approx.) Mass (approx.) Operating temperature Type DC 8.4 V DC 7.2 V 8.5 Wh (1 180 mAh) 38.2 20.5 55.6 mm (1 9/16 13/16 2 1/4 in.) (w/h/d) 76 g (2.7 oz) 0 C to 40 C (32 F to 104 F) Lithium ion

Lens Focal length

GeneralPower requirements Average power consumption (when using the battery pack) DC 7.2 V (battery pack) DC 8.4 V (AC Adaptor) During camera recording using the viewfinder with normal brightness with the XLR adaptor attached: HDV recording 6.4 W DVCAM (DV) recording 5.7 W During camera recording using the LCD with normal brightness with the XLR adaptor attached: HDV recording 6.6 W DVCAM (DV) recording 5.9 W

Design and specifications are subject to change without notice.

HVR-A1J/A1U/A1N/A1E/A1P/A1C 2

ENGLISH

JAPANESE

HDV DVCAM DV HDV 2 2 AUTOONE PUSH INDOOR3 200K OUTDOOR5 800K 15 lx F1.8 0 lx NightShot JEITA *1 *2 16MB 1 1 AC 1 1 1 1 AV 1 1 USB 1 XLR 1 1 1 NP-FM50 1 1 1 1

Exif Ver.2.2*1 MPEG-1 Audio Layer2 16Fs48kHz 384kbps 12Fs32kHz 12 16Fs48kHz NTSCEIA 1080/60i DV DVCAM 18.812mm/

A/V OUT 10 1 Vp-p75 Y 1Vp-p75 C0.286Vp-p75 327mV 47 k 2.2 k COMPONENT Y1Vp-p75 OUT PB/PR, CB/CR525mVp-p 75 3.5

DVCAM DV

HDV 28.218mm/ DVCAM 18.812mm/ DV SP / 63 PHDVM-63DM HDV 41 PHDVM-63DM DVCAM / 63 PHDVM-63DM DV SP 240 PHDVM-63DM AC 145 PHDVM-63DM 5.9mm 1/3 CMOS 297 43 149 169 198 43 276 169 207 T* 10 40 f=5.1 51.0mm 35mm CAMERA TAPE 2 * 41 480mm 169 4350 590mm CAMERA TAPE FULL SCAN 40 400mm 169 4349.3 493 CAMERA MEMORY 40 400mm 169 4337 370 F1.8 2.1 37mm

ACAC-L15A AC100 240V50/60Hz 18W DC 8.4V * 0 +40 20 +60 56 31 100mm 190g

/MIC 3.5 LANC 2.5 INPUT1/ XLR3 INPUT2 -60dBu3k +4dBu10k 0dBu=0.775Vrms USB mini-B HDV/DV i.LINK IEEE13944 S100

* A C

NP-FM50 DC 8.4V DC 7.2V 8.5Wh 180mAh 1 38.2 20.5 55.6mm 76g 0 +40 Li-ion

6.9cm 2.7 169 123 200 560220

7.2V DC8.4V XLR HDV6.4W DVCAM DV 5.7W XLR HDV6.6W DVCAM DV 5.9W 0 +40 20 +60 71 103 191mm 670g 1.1kg NP-FM50 PHDVM63DM XLR


Model information tableModel Destination Color system HVR-A1J J NTSC HVR-A1U US, CND NTSC HVR-A1N E NTSC HVR-A1E AEP PAL HVR-A1P E PAL HVR-A1C CH PAL

Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model


ENGLISH

JAPANESE

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

2. 3.

4.

5. 6.


ENGLISH

JAPANESE

1. 2. 0 3. 4. 5. 6. 270 7. Lead Free 40 350 IC


TABLE OF CONTENTSSection Title Page Section Title Page

1.1-1. 1-2. 1-3. 1-4. 1-5.

SERVICE NOTEPower Supply During Repairs 1-1 To Take Out a Cassette when not Eject (Force Eject) 1-1 Setting the Forced Power On Mode 1-1 Using Service Jig 1-2 Self-diagnosis Function 1-2

6.

ADJUSTMENT

2.

DISASSEMBLY

2-1. Disassembly 2-3 2-2. The Method of Attachment of FP-248, 259 Flexible Board 2-7

3.3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10. 3-11. 3-12. 3-13.

BLOCK DIAGRAMSOverall Block Diagram (1/8) 3-1 Overall Block Diagram (2/8) 3-3 Overall Block Diagram (3/8) 3-5 Overall Block Diagram (4/8) 3-7 Overall Block Diagram (5/8) 3-9 Overall Block Diagram (6/8) 3-11 Overall Block Diagram (7/8) 3-13 Overall Block Diagram (8/8) 3-15 Power Block Diagram (1/5) 3-17 Power Block Diagram (2/5) 3-19 Power Block Diagram (3/5) 3-21 Power Block Diagram (4/5) 3-23 Power Block Diagram (5/5) 3-25

Before Starting Adjustments 6-1 1-1. Adjusting Items when Replacing Main Parts and Boards 6-2 1-2. List of Service Tools 6-4 6-1. Camera Section Adjustments 6-6 1-1. Preparations before Adjustments (CAMERA Section) 6-6 1-2. Initialization of EEPROM Data 6-8 1-3. Camera System Adjustments 6-28 1-4. Electronic Viewfinder System Adjustments 6-58 1-5. LCD System Adjustments 6-63 6-2. Mechanism Section Adjustments 6-66 1. Preparations for Check, Adjustment and Replacement of Mechanism Block 6-66 2. Periodic Inspection and Maintenance 6-66 3. Check, Adjustment and Replacement of Mechanical Parts 6-72 4. Adjustment 6-105 6-3. Video Section Adjustments 6-112 3-1. Preparations Before Adjustments 6-112 3-2. System Control System Adjustments 6-114 3-3. Servo and RF System Adjustments 6-116 3-4. Video System Adjustments 6-118 3-5. Audio System Adjustments 6-122 3-6. XLR Adaptor Adjustments 6-123 6-4. Service Mode 6-126 4-1. Adjustment Remote Commander (RM-95) 6-126 4-2. Adjustment Remote Commander (New Lanc Jig) 6-127 4-3. Data Process 6-128 4-4. Service Mode 6-129

4.4-1. 4-2. 4-3. 4-4. 4-5.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSFrame Schematic Diagrams 4-1 Schematic Diagrams 4-5 Printed Wiring Boards 4-91 Waveforms 4-125 Mounted Parts Location 4-135

* The color reproduction frame is shown on page 6-138 to 141.

5.

REPAIR PARTS LIST

5-1. Exploded Views 5-2 5-2. Electrical Parts List 5-17


1. SERVICE NOTE1-1. POWER SUPPLY DURING REPAIRS

ENGLISH

JAPANESE

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following method is available to prevent this. Method: Use the AC power adaptor (AC-L15A/L15B).

1-2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)1 Refer to 2. DISASSEMBLY to remove the mechanism deck block. 2 Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.

Loading motor DC power supply (+ 4.5Vdc)

1-3. SETTING THE FORCED POWER ON MODEIt is possible to turn on power by adjustment remote commander (RM-95 or NEW LANC JIG). Operate the VTR function using the adjustment remote commander.

1-3-1. Setting the Forced Camera Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:01 and press the PAUSE (Write) button of the adjustment remote commander.

1-3-2. Setting the Forced VTR Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:02 and press the PAUSE (Write) button of the adjustment remote commander.

1-3-3. Exiting the Forced Power ON Mode1) Select page: 0, address: 01, and set data:01. 2) Select page: A, address: 10, set data:00 and press the PAUSE (Write) button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.

HVR-A1J/A1U/A1N/A1E/A1P/A1C 1-1

ENGLISH1-4. USING SERVICE JIGConnect the CPC-7 jig connector (J-6082-382-A) to the CN7005 of NN-001 board.

JAPANESE

CPC-7 (J-6082-382-A)16 8 1 9

NN-001 BOARD (SIDE A)

CN7005

16

1

1-5. SELF-DIAGNOSIS FUNCTION1-5-1. Self-diagnosis FunctionWhen problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD screen what to do. This function consists of two display; selfdiagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.Viewfinder or LCD screenC:31:11

1-5-2. Self-diagnosis DisplayWhen problems occur while the unit is operating, the counter of the viewfinder or LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the repaired by:, block in which the problem occurred, and detailed code of the problem.

Blinks at 3.2Hz

CRepaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer

31Block

11Detailed Code

Refer to 1-5-3. Self-diagnosis Code Table. Indicates the appropriate step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.


ENGLISH1-5-3. Self-diagnosis Code TableSelf-diagnosis CodeRepaired by:

JAPANESE

Block Function 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2

Detailed Code 0 0 0 1 1 2 2 2 2 3 3 4 4 4 4 4 1 1 2 2 2 2 3 3 4 4 4 4 4 0 0 0 0 1 0 1 2 3 0 1 0 1 2 3 4 0 1 0 1 2 3 0 1 0 1 2 3 4

Symptom/State

Correction

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C

Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations.

Use the InfoLITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.


ENGLISHSelf-diagnosis CodeRepaired by:

JAPANESE

Block Function

Detailed Code

Symptom/State

Correction

E

6

1

0

0

E

6

1

1

0

E

6

1

1

1

E

6

2

0

0

E

6

2

0

1

Inspect the lens block focus MR sensor (Pin ql, wa of CN7006 of NN-001 board) when focusing is performed when the focus ring is rotated in the focus manual mode and the focus motor drive circuit (IC7201 of NN-001 board) when the focusing is not performed. Inspect the lens block zoom MR sensor (Pin qh, qj of CN7006 of NN-001 board) when zooming is performed when the zoom switch Zoom operations fault (Cannot initialize zoom lens.) is operated and the zoom motor drive circuit (IC7201 of NN-001 board) when zooming is not performed. Focus lens initializing failure and zoom Inspect the flexible board for breakage or loose connection. lens initializing failure occur simulta- If not faulty, inspect the focus and zoom motor drive circuit (IC7201 neously. of NN-001 board). Steadyshot function does not work well. Inspect pitch angular velocity sensor (SE6802 of EE-001 board) (With pitch angular velocity sensor output peripheral circuits. stopped.) Steadyshot function does not work well. Inspect yaw angular velocity sensor (SE6801 of EE-001 board) (With yaw angular velocity sensor output peripheral circuits. stopped.) Difficult to adjust focus (Cannot initialize focus.)


1. SERVICE NOTE1-1.

ENGLISH

JAPANESE

8.4Vdc10 DCACAC-L15A/L15B

1-2. 1 2. DISASSEMBLY 2 4.5V

+4.5Vdc

1-3. ONRM-95NEW LANC JIG VTR 1-3-1. ON 1) 00101 2) A1001PAUSEWrite 1-3-2. VTRON 1) 00101 2) A1002PAUSEWrite 1-3-3. ON 1) 00101 2) A1000PAUSEWrite 3) 00100


ENGLISH1-4. CPC-7J-6082-382-ANN-001CN7005

JAPANESE

CPC-7 (J-6082-382-A)16 8 1 9

NN-001 BOARD (SIDE A)

CN7005

16

1

1-5. 1-5-1. L C D LCDC:31:11

1-5-2. LCD4 3.2Hz5

3.2Hz

C C H E

31

11

1-5-3. 31 32


ENGLISH1-5-3.

JAPANESE

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2

0 0 0 1 1 2 2 2 2 3 3 4 4 4 4 4 1 1 2 2 2 2 3 3 4 4 4 4 4 0 0 0 0 1 0 1 2 3 0 1 0 1 2 3 4 0 1 0 1 2 3 0 1 0 1 2 3 4

LOAD UNLOAD UNLOADT UNLOADS T S FG FG FG PG FG PG

LOAD UNLOAD UNLOADT UNLOADS T S FG FG FG PG FG PG


ENGLISH

JAPANESE

E

6

1

0

0

MR NN-001CN7006 ql, wa NN-001 IC7201 MR NN-001CN7006 qh, qj NN-001IC7201 NN-001IC7201

E

6

1

1

0

E

6

1

1

1

E E

6 6

2 2

0 0

0 1

PITCH EE-001SE6802 PITCH YAW EE-001SE6801 YAW

HVR-A1J/A1U/A1N/A1E/A1P/A1C 1-8E

2. DISASSEMBLYLinkDISASSEMBLY THE METHOD OF ATTACHMENT OF FP-248, FP-259 FLEXIBLE BOARD HELP

HVR-A1J/A1U/A1N/A1E/A1P/A1C

2. DISASSEMBLY

2. DISSASSEMBLYNOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, dont pull at wire of connector. It is possible that a wire is snapped. When installing a connector, dont press down at wire of connector. It is possible that a wire is snapped.Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)

NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)When disconnecting the harness (coaxial cable), do not pull the harness part but pull off the connector body with tweezers etc.

Harness (coaxial cable) Tweezers etc.


2. DISASSEMBLYThe following flow chart shows the disassembly procedure.

HELP

2-1. DISASSEMBLY5 5 7 5 3 6 3 8 2 4 6 qa 2 4 0 1 1 1 2 3 4 5 6 7 8 3 1 5 2 6 7 8 9 0 4 qa 1 2 3 4 5 6 7 8 9 0 qa Screw (M1.7) x2 Claw x2 P cabinet (C) assembly Flexible board x5 P2 lock ace screw x1 PP-001 board P2 lock ace screw x2 Panel frame Panel insulating sheet D9001, LCD9001 Panel cushion 9 2 3 7 5 4 3 1 7 1 2 3 4 Screw (M1.7) x2 Screw (M1.7) x1 Boss x1 Cold shoe frame 6 8 1 4 2 1 Open the LCD. Screw (M1.7) x1 Lifting up the EVF lens block. Screw (M1.7) x1 Screw (M1.7) x3 Turn down the EVF lens block. Claw x1 Cabinet (upper) block qd 2 1 2 3 4 5 6 7 8 Screw (M1.7) x2 Screw (M1.7) x7 Spring P2 lock ace screw x4 Accessory shoe Claw x1 Cold shoe cabinet Screw (M1.7) x2 9 Open the jack cover (rear). 0 Screw (M1.7) x1 qa Remove the cabinet (R) block . qs Flexible board x2 qd Cabinet (R) block qs 9 1 2 3 4 Tape (A) x1 Screw (M1.7) x2 Flexible board x1 Battery panel block to Page 2-5 1 4 5 7 2 8 3 2

8

4

1 2 3 4 5

Connector x1 Screw (M1.7) x1 Claw x1 Flexible board x1 External connector

6 7 8 9

Sheet (HS) x1 HELP Flexible board x2 P2 lock ace screw x1 OO-001 board

HVR-A1J/A1U/A1N/A1E/A1P/A1C2-3 2-4

2. DISASSEMBLY

HELP

1

9 5 9 2 5 0 4

9 3 2 8 5 8 5 6 7 4 2 4 2 4 1

from Page 2-4 5

3

4 6 1 2 3 4 P2 lock ace screw x1 Claw x1 Flexible board x1 DC-IN connector section 5 Flexible board x3 6 Connector x1 7 8 9 0 7 1 1 2 3 4 5 6 7 8 9 Lifting up the lens block. Screw (M1.7) x1 Screw (M1.7) x1 Screw (M1.7) x1 Boss x2 Remove the EVF lens block. Tape (A) x1 Flexible board x1 EVF lens block

2 5 3

P2 lock ace screw x2 Remove the TT board. Flexible board x2 TT board

1 2 3 4 5

Flexible board x2 HELP Flexible board x6 P2 lock ace screw x1 Hook x3 NN board

Refer to page 2-1 " Note for disconnecting the harness (coxial cable) ".

5 2

3 4 2 1 1 3 2 5 4 1 2 3 4 5 Flexible board x2 Claw x2 Tape (A) x1 P2 lock ace screw x1 Lens block assembly 1 1 Screw (M1.7) x1 2 P2 lock ace screw x3 3 Screw (M1.4x1.5) x3 4 MD frame assembly 5 Mechanism deck

HVR-A1J/A1U/A1N/A1E/A1P/A1C2-5 2-6

2. DISASSEMBLY2-2. THE METHOD OF ATTACHMENT OF FP-248, FP-259 FLEXIBLE BOARD FP-248 FLEXIBLE BOARD FP-248 flexible board Hinge cover (rear) Fold 3An angle is folded.

Fold

FP-259 FLEXIBLE BOARD 1The A and A, B and B section are united and an angle is folded. FP-259 flexible board Adhesive tape Fold

2An angle is folded.

Adhesive tape B

Fold to Page 2-8

A Adhesive tape Fold


2-7

2. DISASSEMBLY4Set the hinge assembly in the shown below.

from Page 2-7 Hinge assembly 3Flexible clamp

5Roll the the FP-259 flexible board 1.5 times, in the direction of arrow A.

A

Adhesive tape

Claw

7Hinge cover (rear)

8Screw

Claw 6Hinge cover (front)


2-8E

HELPSheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

Sheet (DD) TT board

FP-261 flexible board

Shield sheet (BT)

Fold Fold FP-251 flexible

FP-250 flexible Fold Fold

Sheet (HS)

Sheet (HS) (Inserts it between the OO-001 board and the cabinet)

OO-001 board Fold


HELP

3. BLOCK DIAGRAMSLinkOVERALL BLOCK DIAGRAM (1/8) OVERALL BLOCK DIAGRAM (2/8) OVERALL BLOCK DIAGRAM (3/8) OVERALL BLOCK DIAGRAM (4/8) OVERALL BLOCK DIAGRAM (5/8) OVERALL BLOCK DIAGRAM (6/8) OVERALL BLOCK DIAGRAM (7/8) OVERALL BLOCK DIAGRAM (8/8) POWER BLOCK DIAGRAM (1/5) POWER BLOCK DIAGRAM (2/5) POWER BLOCK DIAGRAM (3/5) POWER BLOCK DIAGRAM (4/5) POWER BLOCK DIAGRAM (5/5)


3. BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM (1/8)EE-001 BOARDLENS BLOCK IRIS (SHUTTER) 42 39 IC6601 CMOS 7 IMAGER 10 11 12 38 37 DRVOUT_GR1, DRVOUT_GR2, DCOUT_GR1, DCOUT_GR2 10 7 10 7 DRVOUT_GR1, DRVOUT_GR2, DCOUT_GR1, DCOUT_GR2 CN6401 DRVOUT_GB1, DRVOUT_GB2, 14 DCOUT_GB1, DCOUT_GB2 11

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.TT-001 BOARD (1/7)CN1013 DRVOUT_GB1, DRVOUT_GB2, 14 DCOUT_GB1, DCOUT_GB2 11

DRVOUT_R, DRVOUT_B, DCOUT_R, DCOUT_B

6 3

6 3

DRVOUT_R, DRVOUT_B, DCOUT_R, DCOUT_B

A9 A10 B9 B10 E9 E10 F9 F10 J9 J10 K9 K10

A3 D3 A4 E4 A5 E5 B1 H1 B2 H2 J2 J4 K2 K4 F3 F5 G3 G5 H3 H4 IC1201 CDS, A/D CONVERTER (1/21) F7 E6 E7 H5 G6 F6 D6 D7 K5

RIN0 RIN13

108 116 119 120 123 125 126 133 136 141

69 12 15 18 20 24 28 50 52

IFI_Y0 IFI_Y7 CAMERA IFI_C0 IFI_C7

116 114 112 109 107 105 102 100 208 201 15 17 19 IC1601

115 113 111 108 106 103 101 99 91 98 117 119 61 83 76

HDI_Y0 HDI_Y7 CAMERA, MS, HDV PB, HDV-i.LINK HDI_C0 HDI_C7

135 361 136 362 137 363 140 366 355 130 356 358 133 359 134 360 161 382 386 196 374 376 151 377 152 378 153 379 141 144 370 145 371 146 373 148 156 381 155 202 IC2201 (1/5)

GIN0 GIN13

IFI_HDO, IFI_VDO, IFI_OEO

BIN0 BIN13

155 160 163 170 29 32 107 41 43 44

JPEG ENCODER, MS SIGNAL PROCESSOR (3/21)

HDI_HD, HDI_VD, HDI_OE AUIN3

ADC_SO, ADC_SCK, XCS_ADC_0 CLPOB TGHD, TGVD XSYS_RST CAM_LATCH_VD CHCK

IC1401 CAMERA SIGNAL PROCESSOR (2/21) 71 21 3 5 6 8 9 11 IC1801 12 14 77 79 128M 80 82 83 85 86 88 32 34 SDRAM 35 37 38 40 (3/21) 41 43 48 50 51 53 54 56 57 59

23 16 17 27 19 18 15

CHCK IC6406 TGHD_1, TGVD_1 7, 5 1, 3

1 26 27 20

1 26 27 20

CHCK

HDO_Y0 HDO_Y7 HDV PB, HDV-i.LINK, DV PB, DV-i.LINK HDO_C0 HDO_C7

TGHD, TGVD

SDM_CK SD_XCS

135 148 170 162 160 158 156 153 191 179 175 173 144 137 133 128

72 65 84 86 62 44 192

XSYS_RST AHS_SO_1, AHS_SCK_1, IC6407 XCS_AHS_1 2, 5, 7 6, 3, 1

XSYS_RST

HDO_HD, HDO_VD, HDO_OE_MH IC_2201_ADAO2 CK56MFO2 SRCKO VCK

30 28

30 28 A_2.8V

SDM_DQ0 SDM_DQ31 SDM_A0 SDM_A11, SDM_BA0, SDM_BA1

SE6801 YAW SENSOR SE6802 PITCH SENSOR

6

IC6801

20

YAW_AD

1 23 23 24 22 X1401 89.010 MHz : NTSC 74.250 MHz : PAL

IC1403 CLOCK GENERATOR (2/21)

5

CHCK

195

22 28 63 69

BASE BAND SIGNAL PROCESSOR 143 (4/21) 132 22

PITCH/YAW 10 SENSOR 16 AMP 17

PITCH_AD VST_C_RESET

24 22

XSYS_RST AHS_SO, AHS_SCK, XCS_AHS

78 142 39 40 34 PNDCK 100 91 93 80 79 33

229 225 232 234 239 242 245 248 251 255 198 201 204 207 210 213 215 216

SD_CK SD_XCS

VCK 17 34 53 49 50 46 47 43 44 40 13 11 10 8 7542 33 32 29 30 27 26 24 23 22 21 31 20 36 35 IC1402 128M SDRAM (2/21) 34 27 22 20 18 16 14 11 9 2 25 36 58 59 MS D0_VM D15_VM

SD_DQ0 SD_DQ15

1A16_VM A23_VM DSCK_MH XCS_MH_VM SFD_LRCK CK64FSO

OVERALL (3/8) (PAGE 3-5)

NN-001 BOARD (1/4)IRIS METER CN9205 CN9206 7 1 2 4 3 5 14 8 11 9 12 10 24 FOCUS 25 F_MR_A, 21 F_MR_B 19 ZOOM_A, ZOOM_B, Z00M_XA, 30 ZOOM_XB 33 Z_MR_A, 16 Z_MR_B 17 26 29 23 27 33 32 30 31 29 20 26 23 25 22 24 10 9 13 15 4 1 18 17 8 5 11 7 1 2 4 3 5 14 8 11 9 12 10 24 25 21 19 30 33 16 17 26 29 23 NF_DRIVE 7 1 IC7203 IC7204 NOISE FILTER (1/5) 7 1 CN7006 I_DRIVE I_BIAS I_HALL H1 J1

IC7201 (1/5)

EN1, DIRA1, DIRB1

SD_A0 SD_A11, SD_BA0, SD_BA1

MH

IRIS C6 DRIVE, A5 HALL AMP C5 B6 K2 L2

CAM_VD CAM_LATCH_VD TG_FLD

2 3


ND FILTER METER

YAW AD 130 PITCH AD 129 VST C RESET 40 CN7008 (1/3) K12 L12 K11 J11 H12 J12 H11 78 67 68 66 63 73 75 CN1001 (1/3) PNDCK 77 CAM_VD 66 67 65 62 72 74

17 20 52 45 33 29

XCS_IC_1401_BUS IC_1401_BUS_CLK

60 77 54 73 70 67 60 58 4 82 SRCKO EXT_STROBE_ON 177 63

KASYAON


MH

ND_DRIVE ND_BIAS ND_HALL IC7205 NOISE FILTER (1/5)

48 47 46

VSP_SO, XVSP_SCK XCS_MH_MZ

ND A11 FILTER A9 DRIVE, HALL C10 AMP B11 2 F3

TG_FLD 185 CAM_LATCH_VD 181 203 78 77 75 161 183

D24A00_SS D31A07_SS, DXXA08_SS DXXA12_SS

IC5802 CAMERA CONTROL (16/21)

FOCUS MOTOR

9 8 186 XFTR_NR

4XSYS_RST XFTR_NR SYS_V


MFOCUS MR SENSOR

CAM_SI, CAM_SO, CAM_SCK, XCS_IC_7201 XRST_IC_7201

FOCUS MOTOR B1 DRIVE C4 K6 F1 E12 E10

ZOOM MOTOR

M

2

ZOOM MR SENSOR NF MOTOR

ZOOM MOTOR DRIVE

K9 L9 M9 J9

74 72 70

73 71 69

EN1, DIRA1, DIRB1 201 135 SYS_V ZOOM_VR_AD

XSYS_RST EXT_STROBE_ON SYS_V ZOOM_VR_AD

5


MLENS TEMP SENSOR

L6 NF MOTOR L8 DRIVE L7 M8

71 69 53

70 68 52

NF_EN, NF_SW

132 131 127

TEMP OUT

LENS TEMP AD

65 66 63 64

HI_SI, HI_SO, XHI_SCK XCS_CAM_COM

HI_SI, HI_SO, XHI_SCK XCS_CAM_COM

6


FP-246 FLEXIBLE BOARDPH001, 002 CN9204 MANUAL FOCUS/ZOOM SENSOR 4 2 1 MF_LED MF_A, MF_B CN9201 (1/2) 3 5 6 25 23 22 CN1006 (1/2) MF_LED MF_A, MF_B Q5801 LED DRIVE

3 X5801 20MHz 1 10 87 86 84 XCS EEP IC5801 7 6 64k EEPROM (16/21) 3 2

142 210 211

05

YY-001 BOARD (1/2)

CAM_EEP_SI, CAM_EEP_SO, CAM_EEP_SCK

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL

HVR-A1J/A1U/A1N/A1E/A1P/A1C 3-1 3-2

3-2. OVERALL BLOCK DIAGRAM (2/8)TT-001 BOARD (2/7)169 395 170 396 171 397 172 398 164 390 165 391 166 392 167 393 174 399 173 162 163 8 12 14 16

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

IC_2607_Y0 IC_2607_Y7 HDV REC, HDV-i.LINK IC_2607_C0 IC_2607_C7

78 79 81 86 18 19 21 26 3 2 4 60 1 IC2607 75 76 77

EBS[0] EBS[7] KCLK ERDY ERE 3 IC2605 21 10 LEVEL 14 SHIFTER (5/21) 2 22 IC2603 (5/21) 7 3 1 2 6 5 XCS_IC_2607 4 IC2604 (5/21) IC_5601_MCLK HDAT[0] HDAT[7] 1 2 IC2606 (5/21) 2 4ADDRESS BUS DATA BUS

HDV REC, HDV-i.LINK EBS[0] EBS[7] KCLK ERDY ERE

296 304 296 316 321 73 74 76 77 IC3801 HDV STREAM PROCESSOR (10/21) 80 82 84 85 HDV REC, DV REC RECDT RECCK RECA1, RECA2

IC_2607_HDO, IC_2607_VDO, IC_2607_FLDO IC_2607_CK27MFOL IC_2607_CK56MFO3

HDV-MPEG VIDEO ENCODER 251 254 (5/21) 256 259

8


HDAT[0] HDAT[7]

7OVERALL (3/8) (PAGE 3-6)

CRECDT CRECCK

DV REC

CRECA1, CRECA2

BMDT00 BMDT31 IC2201 (2/5) BASE BAND SIGNAL PROCESSOR (4/21)

89 90 92 96 98 100 102 103 105 106 108 110 111 113 115 117 118 120 121 122 120 124 126 128 130 131 175 176 178 180 181 183 185 186 188 189 191 195 197 201 203 205 207 208 210 214 216 217 154 156 157 159 160 162 163 165 166 168 169 172 173 136 133

242 243 245 246 248 249 241 IC2601 247 4 D-FFs (5/21)

IC2801 IC2806 BUFFER (5/21)

HADR[0] HADR[3]

2 1

IC_5601_WR0X IC_5601_RDX

IC3001 IC3002 128M SDRAM (6/21) BMDT32 BMDT63 OMAD00 OMAD10, OMADB0, OMADB1 OMCE0X OMCLK

256 257 259 260 262 264 265 266 241 243 244 245 246 248 249 251

IC2602 (5/21) 4 2 XRST_IC_2607 INT_IC_2607 IC_5601_WR0X IC_5601_RDX

HADR[0] HADR[7]

73 260

107 339 108 340 109 341 110 342 102 334 103 335 104 336 105 338 115 344 347 111

VY[0] VY[7] HDV PB, HDV-i.LINK VC[0] VC[7]

269 267 263 261 257 256 289 281 280 283 276 277 275 272 287 286 251 IC3201

253 254 HDV PB, HDV-i.LINK BS[0] BS[7] BSEN BSERR DJCLK 11 13 14 17 18 21 22 23 27 28 10 HDV-i.LINK PD10 PD17 PCLK1 DIR1 XPEN1 XPACC1 HDV PB VITDT VITCK

215 225 223 221 220 231 227 224 232 236 226 222 208 219 216 202 190

BS[0] BS[7] BSEN BSERR DJCLK XCS_IC_3201 IC_3201_XPS IC_5601_WR0X IC_5601_RDX XRST_IC_3201 INT_IC_3201

71 72

9


DHD, DFD, DF_SYNC

CK_IC_3201_O2

MYD0 MYD31 IC3401 128M SDRAM (Y) (8/21) MYA0 MYD10 MYCKO

MCD0 MCD31 IC3402 128M SDRAM (C) (8/21)

MCA0 MCD10 MCCKO

418 416 17 AUIN21 CK13MFO2

ADATAIN0

45 74 97 SFD_LRCK CK64FSO 43 73 41 71

59 60 IC3601 MPEG AUDIO SIGNAL PROCESSOR (9/21) 35 47 36 44 53 54 38 42 48 49 127 129 98 17 58 69 81 95 120 124 135 6

AUDAI, AUENI AUDAO, AUENO AUSYNADDRESS BUS

XSYS_RST

291

DSCK_VM HADR[0] HADR[13]

44 37 33 28

9 8

VSP2_SI, VSP2_SO, XVSP2_SCK, XCS_IC_5601

252 8 13 3 11 9 14 16 18 34 33 35 21 24 6 23 4 59 71 58 80 69 84 68 89 90 74 85 79 82 72 75 63 47 49 61 64 66 53 52 55 44 42 48 41 99 111 97 109 100 110 118 116 105 113 95 104 94 103 92 148 156 150 160 158 161 155 172 175 170 176 171 173 168 166 165 145 147 151 163 134 135 137 124 123 115 144 125

HDV-MPEG VIDEO DECODER (7/21)

179 181 185 187 189 192 191 193 194 196 199 201 204 205 207 210 211 213 218

HDAT[0] HDAT[7]

HADR[0] HADR[13]

XCS_IC_3601 XCS_IC_3201 XCS_IC_2607 IC_5601_MCLK IC_5601_WR0X IC_5601_RDX IC_3201_XPS XRST_IC_3201 XRST_IC_3601 XRST_IC_2607 INT_IC_2607 INT_IC_3201

15 16 17 20 24 25 26 154 155 156 207 208 52 45

18 152

IC_5601_XCS_IC_3801 XRST_IC_3801_0

IC5601 HDV-LSI CONTROL (18/21)

153 212 3 X5601 20MHz 1 204 FRRV, TRRT 203 65 66 63 64

XRST_IC_3801_1 INT_IC_3801

240 40 230 348 232 268

187 189 193 195 197 185 200 201 199 213 214 217 219 222 224 204 205 207 235 229 228

10D24A00 D31A07, DXXA08 DXXA10


FRRV, TRRT, DRP

HDAT[0] HDAT[7]

AUDAI, AUENI AUDAO, AUENO AUSYN IC_2201_PCRERR IC_2201_SRCH IC_2201_CK27MFO1 IC_2201_FLD27MF

276 277 279 281 287 3 5 1 7

DJCLK IC_5601_WR0X IC_5601_RDX XRST_IC_3601 XCS_IC_3601 HDAT[0] HDAT[7] HADR[0] HADR[3]

DATA BUS

203 225

XCS_IC_3801 SCWIN_IC_3801

11VSP2_SI, VSP2_SO, XVSP2_SCK, XCS_IC_5601 XSYS_RST DSCK_VM IC_2201_CK27MFO1 ADATAIN0 SFD_LRCK CK64FSO


IC_2201_PCRERR 99 IC_2201_SRCH 100 IC_2201_CK27MFO1 189 IC_2201_FLD27MF 332 198 188 SFD_LRCK CK64FSO

62 18 39 46

12 13



OVERALL (4/8) (PAGE 3-7) OVERALL (1/8) (PAGE 3-2) 05

18 2

CK13MFO2 SFD_LRCK CK64FSO

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL A : VIDEO/AUDIO/SERVO SIGNAL

SFD_LRCK CK64FSO

14



3-3. OVERALL BLOCK DIAGRAM (3/8)TT-001 BOARD (3/7)OVERALL (2/8) (PAGE 3-4)


9

VITDT VITCK

HDV PB

86 30

139

RFIN

HDV PB, DV PB

RFIN

16


290 53 291 292 288 51 289 52 50 287 419 201 45 283 46 285 43 281 44 282 280 41 197

RYI0 RYI3 DV PB RCI0 RCI3 HYI, HCI ADATAOUT0, ADATAOUT1

13 72 14 73 123 166 124 125 12 75 167 126 119 162 120 163 70 121 71 122 164 165 ADATAIN0 127 168

45 41 IC4001 DV SIGNAL PROCESSOR (11/21) 48 47 149 186 150 187 104 51 106 151

CRECDT CRECCK CRECA1, CRECA12

DV REC

CRECDT CRECCK CRECA1, CRECA2

7


DV-i.LINK LBUS0 LBUS3 TRCKO DIR XENA XACC HDV-i.LINK PD10 PD17 PCLK1 DIR1 XPEN1 XPACC1 FRRV, TRRT, DRP D24A00 D31A07, DXXA08 DXXA10

95 98 104 91 76 75 77 79 81 85 87 91 76 75 FRRV, TRRT 105 D24A00 D31A07, 108 DXXA08 DXXA11 51 56 58 59 61 64 IC4201 HDV/DV i.LINK INTERFACE (12/21)

149 X4201 24.576MHz 150 139 136 HDV-i.LINK, DV-i.LINK TPA, TPB CN1003 (1/4) 35 37 33 31 45 43 47 49

RR-001 BOARD (1/4)CN9001 (1/4) CN9003 TPA, TPB 9 12 9 12 NTPA, TPA, NTPB, TPB

II-001 BOARDCN102 CN103 1 4 HDV/DV

RYO0 RYO3 DV REC RCO0 RCO3 HYO, HCO ADATAIN1

10OVERALL (2/8) (PAGE 3-4)

5 50 76 88 106

IC_4201_PLL_ON XCS_IC_4201 XIC_4201_INT FR1 OFR2

IC2201 (3/5) BASE BAND SIGNAL PROCESSOR (4/21) 48 39 277 FLAT_SYNC_FYO0 VLAT_SYNC_FCI VLAT_IN_FYO1 VCK 18 76 77 143

14 151

XRST_VTR 54 107 152 189 55 153 190 109 155 192 188 158 62 60 58 111 112 59 157 114 3 D24A00 D31A07, DXXA08, DXXA09 XCS_IC_4001_BUS XCS_IC_4001 XRST_IC_4001 SWP FRRV, TRRT, TRRV, DRP D24A00 D31A07, DXXA08 DXXA11 XCS_IC_4001_BUS XCS_IC_4001 XRST_IC_4001 SWP FRRV, TRRT, TRRV, DRP VSP_SI, VSP_SO, XVSP_SCK

17


IC_2201_CK27MFO1 CK64FSO SFD LRCK

15 21 78

VSP_SI, VSP_SO, XVSP_SCK

254 255 258 257 19 207 428 440 55

FRRV, TRRT, TRRV

VSP_SI, VSP_SO, XVSP_SCK XRST_VTR XRST_PLL XSYS_RST XCS_SZ DSCK_VM 21 22 4 IC2001 BUS BRIDGE (15/21) 2 33 32 56 31 55 30 54 29 53 28 52 27 26 24 23 7 38 8 10 40 11 41 12 42 43 14 44 15 45 16 18 20 6 19 XCS_SZ_SI 73 XCS_SDRAM_VM 19 71 185 186 168 177 IC4802 (1/3) DS CONTROL, FLASH (14/21) USB_DET USB_CLK 4 2 IC4803 OSC DRIVE (14/21) X4801 48MHz USB_D 42 44 41 38 36 39 USB_D D9006 6 6 4 3 4 3

CN104 D VCC 3 2 (USB) 1

IC5001 64M SDRAM (15/21) 20 26 29 35 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 38

D0_VM D15_VM

A1_VM A19_VM

234 452 233 451 232 450 231 449 230 448 229 447 228 445 226 444 224 442 223 MS D0_VM D15_VM

D0_VM D15_VM

A1_VM A14_VM

DSCK_MH

15 252 14 251 13 250 12 249 11 248 10 247 9 246 8 245

D0_SZ D15_SZ

DSCK_MH XCS_MH_VM

WW-001 BOARDCN1011 CN301 6 7 4 5 14 6 7 4 5 14 MS_DIO, MS_BS, MS_SCLK MS_INSERT Q301 LED DRIVER D301 (MS ACCESS) CN302 4 2 8 6 MEMORY STICK DUO 81 85 78 80 277

D0_VM D15_VM

16 18 21 24 27 35 279 286 289 292 1 4 7 13 XCS_MH_VM 74 122 309 307 69 124

MS_DIO, MS_BS, MS_SCLK XMS_IN MS_LED_ON


1

A16_VM A23_VM VCK XCS_MH_VM DSCK_MH XRST_PLL XSYS_RST

A1_VM A23_VM

DSCK_MH


15 13

XCS_FLASH DSCK_VM IC_2201_CK27MFO1 ADATAIN0 CK64FSO SFD_LRCK SFD_LRCK


A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL A : VIDEO/AUDIO/SERVO SIGNAL

05


3-4. OVERALL BLOCK DIAGRAM (4/8)TT-001 BOARD (4/7)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.NN-001 BOARD (2/4)XRST_VTR CN1001 (2/3) CN7008 (2/3) 3 53 49 55 57 4 54 50 56 58 27 57 55 47 34 11 13 35 34 VSP_SO, XVSP_SCK 38 36 IC7401 (3/3) (3/5) SERIAL INTERFACE IC7401 (1/3) (3/5) DRUM_VS DRUM MOTOR DRIVE FG AMP PG AMP DRUM_U, DRUM_V, 63 DRUM_W 65 68 52 49 CN7001 5 10 1 2 RFIN RECDT RECCK RECA1, RECA2

25

OVERALL (5/8) (PAGE 3-10) 35 46 44 40 42 39 37 45 RF_MON SWP 30 38 CN7003 IC7601 REC/PB AMP (2/5) 10 9 4 3 XODD, YODD XEVEN, YEVEN 5 6 9 8

N MECHA DECK (MDX-N101)VIDEO HEAD

OVERALL (3/8) (PAGE 3-6) OVERALL (2/8) (PAGE 3-4)

16 8

RFIN RECDT RECCK

HDV PB, DV PB HDV REC, DV REC

ODD

RECA1, RECA2

CONT1, SW_PS, ALL_PS

26 56 54 CK13MFO2 XRST_VTR 46 33 10 12

CONT1, SW_PS, ALL_PS

EVEN


18

CK13MFO2

VSP_SO, XVSP_SCK

172 29 28 7 32k EEPROM 6 3 (17/21) 2 IC5402 XCS EEP EEP_SI, EEP_SO, EEP_SCK 10 87 86 84

20 88 89 IC5401 MECHA CONTROL (17/21) 3 X5401 20MHz 1

XCS_IC_7401 DRUM_PWM CAP_PWM

8 25 29

9 26 30 Q7403XFFREW_UP

37 44 41 LPF DRUM_PG 43 CAP_ERROR 9 4 3 IC7001 CAPSTAN PWM DRIVE (3/5) CAP_VS 75 77 1 80 CAPSTAN MOTOR DRIVE 12 45 DRUM_ERROR 9 4 3 IC7002 DRUM PWM DRIVE (3/5) 12 64 67 53 50

M9001 DRUM MOTOR

MDRUM FG DRUM PG

DRUM_FG

DRUM_FG_SENS DRUM_PG_SENS


19

XSYS_RST XRST_VTR IC_4201_PLL_ON XCS_IC_4201 XIC_4201_INT FR1 OFR2

9 100 154 18 157 159 199 52 45 33 30 26 215 12 164 171 178 179 163 70 69 67

D7001

197 198 166 165 190

DRUM_FG DRUM_PG CAP_FWD, CAP_ON CAP_FG

30 28 32 34 20

31 29 33 35 21

74 76 78 10 15 7 8

CAP_U, CAP_V, CAP_W

CN7004 9 20 2 7 27 24

M9003 CAPSTAN MOTOR

MHU, HV, HW

CAP_FWD, CAP_ON

UHE, VHE, WHE


17

D24A00 D31A07, DXXA08 DXXA11 XCS_IC_4001_BUS XCS_IC_4001 XRST_IC_4001 SWP FRRV, TRRT, TRRV, DRP

CAP_FG

4

FG AMP

FG1, FG2

CAPSTAN FG

CN7002 119 106 108 DEW_DET 21 15 17 19 22 16 18 20 DEW_DET 6 7 9 DEW SENSOR S9003 MODE SWITCH

MODE_SW_A MODE_SW_C

MODE_SW_A MODE_SW_C IC7401 (2/3) (3/5) LOAD, UNLOAD LM_LIM_DET 32 33 31 LOADING MOTOR DRIVE 69 72 LM

VSP_SI, VSP_SO, XVSP_SCK VSP_SO, XVSP_SCK OVERALL (1/8) (PAGE 3-2)

M9002 LOADING MOTOR 1 4

4

XCS_MH_MZ XFTR_NR SYS_V XPWAD, XPWDA VSP_SO, XVSP_SCK XCS_IC_4401 XCS_AUVOL XEXT_MIC_ON HP_JACK_IN

11 117 181 96 97

15 13 138

LOAD, UNLOAD LM_LIM_DET

37 38 35

38 39 36

MQ9001 TAPE END SENSOR Q9002 TAPE TOP SENSOR H9002 T REEL SENSOR H9001 S REEL SENSOR LED9001 TAPE LED

196

TAPE_END

18

19

TAPE_END

21

TAPE END 20 DETECT TAPE TOP 18 DETECT T REEL FG AMP S REEL FG AMP 26 27 22 23

TAPE_END_C

28


20

43 168 134 158 83 82 80 39 38 63 65 66 64

195

TAPE_TOP

16

17

TAPE_TOP

19

TAPE_TOP_C

16

192

TREEL_FG

24

25

TREEL_FG

29

T_REEL_

20 19 22 23 25

VD_SI, VD_SO, XVD_SCK XCS_EVF XCS_LCD OVERALL (5/8) (PAGE 3-9)

193 180

SREEL_FG TAPE_LED_ON

22 14

23 15

SREEL_FG Q7402 LED DRIVE

25

S_REEL_ TAPE_LED_K

21

HI_SI, HI_SO. XHI_SCK XCS_IC_5401 REC_PROOF CHIME_SDA, CHIME_SCK XCS_IC_3801 SCWIN_IC_3801

MIC9003 S9002 REC PROOF 11 13 14 4PIN CONNECTOR S9001 CC DOWN XCC_DOWN 18

REC_PROOF CHIME_SDA, CHIME_SCK


11

16 170 74 73 71 202 213 214 201 206 152 131 128 127 133

VSP2_SI, VSP2_SO. XVSP2_SCK. XCS_IC_5601 XCS1_IC_2201 XCS2_IC_2201 LINE_OUT_VD IC_2201_HOSDVD XLINE_CNT1A, XLINE_CNT1B, XLINE_CNT2, XLINE_CNT3A, XLINE_CNT3B

XFFREW_UP 85 REC_CRRT0, 81 REC_CRRT1 177

36 43 42

37 44 43

REC_PROOF, CHIME_SDA, CHIME_SCK


22

A : VIDEO/AUDIO/SERVO SIGNAL A : SERVO SIGNAL


23

XD4CN XPSV_D4

CN1004 (1/3) XCC_DOWN OVERALL (7/8) (PAGE 3-14) 72 51 74 55 77 76 78 73 52 75 56 78 77 79

CN7009 (1/3) XCC_DOWN SWP VO10B FRRV REC_CRRT0, REC_CRRT1 CN7005 (1/2) SWP 11 RF_MON 9 CPC FRRV 12 (FOR CHECK) REC_CRRT0, REC_CRRT1 14 13

24

VO10B FRRV REC_CRRT0, REC_CRRT1

05



( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.NN-001 BOARD (3/4)Q2404 2406 CN1004 (2/3) EVRE EVGR EVBL 69 67 65 70 68 66 CN7009 (2/3) EVRE EVGR EVBL 48 47 46 20 22 24 12 27 35 22 20 13 2 6 8 15 26 HCK1, HCK2, HST, RGT, DWN, EN, STB, VCK, VST, PCG 12 3 VR VG VB COM Q7808, 7809 PSIG DRIVE CN7801 26 25 24 27 1 2 3 4 1 27

UU-001 BOARDCN9803 VR VG VB COM PSIG CN9802 15 16 14 18 17 LCD9002

73 72 74

BUFFER

IC7801 EVF DRIVER (4/5)

297 65

XEHD, XEVD

75 73

76 74

XEHD, XEVD HDO

1 48 2

45 46 42 23 20 18 13 IC7802

COLOR EVF UNIT

40 VD_SI, VD_SO, XVD_SCK 39 XCS_EVF 41

IC2201 (4/5) BASE BAND SIGNAL PROCESSOR, D/A CONVERTER (4/21)

CN1001 (3/3) XCS_EVF

CN7008 (3/3) 11 12

TIMING 8 GENERATOR (4/5) 44 30 Q7803 36

3 Q7807 4

25

LED_ON/OFF

Q9801 EVF BACKLIGHT CONTROL 1 + 3 4

Q9802 EVF BACKLIGHT DRIVE

D9801 (EVF BACKLIGHT)

24

LED_DA IC9801 EVF BACKLIGHT CONTROL

VD_SI, VD_SO, XVD_SCK

7 13 9

8 14 10

VD_SI, VD_SO, XVD_SCK CN7005 (2/2) EVF_COM_DC EVF_VG EXT_DA PSIG EVF_VCO 1 5 3 6 4 CPC (FOR CHECK)

XRST_VTR

25


RR-001 BOARD (2/4)Q2401 2403 68 69 67 64 56 BUFFER CN1003 (2/4) PLRE PLGR PLBL 1 3 5 19 21 25 28 27 26 79 77 75 61 59 55 52 53 54 CN9001 (2/4) PANEL_R PANEL_G PANEL_B CN9004 (1/2) 26 25 27 16 15 9 6 7 8 2 3 1

PP-001 BOARD (1/2)CN8701 (1/2) PANEL_R PANEL_G PANEL_B 37 36 35 52 2 46 49 48 47 34 20 22 23 24 VR VG VB COM LCD9001 CN8704 4 5 3 1 23 24 2 6 8 11 14 19 22

IC8701

XPHD, XPVD

PANEL_HD, PANEL_VD

12 PANEL_XHD, PANEL_XVD 13 19 22 VD_SI, VD_SO, XVD_SCK 21 20 XCS_LCD EXTDA PWM BL_CONT

LCD DRIVER 29

VD_SI, VD_SO, XVD_SCK XCS_EVF XCS_LCD



6 13 16 18 31 26

RGT, HCK1, HCK2, HST, PCG, XSTBY, DWN, EN, VCK, VST, REF, VP

2.7 inch WIDE COLOR LCD UNIT

XCS_LCD

XCS_LCD


21REC_PROOF CHIME_SDA, CHIME_SCK 231 135 136 243 244 97 99 234 IC4802 (2/3) 137 138 245 TP_SEL2 Q4806 TP SELECT SWITCH

BL_CONT

17

63

BL_CONT

17

11

TP_X TP_Y TP_SEL1

24 22 23

56 58 57

TP_X TP_Y TP_SEL1

10 12 11

18 16 17

TP_X TP_Y TP_SEL1 TOUCH PANEL I/F Q8701, 8702

CN8703 TP_TOP 5 TP_L 2 TP_R TP_BOT 1 4

HI_SI, HI_SO. XHI_SCK XCS_IC_5401

TOUCH PANEL


6 26

HI_SI, HI_SO. XHI_SCK XCS_CAM_COM 230

HI CONTROL 246 (14/21)

Q8706, 8707 Q8708, 8709 XCS_EEP, EEP_XRDY, EEP_RXD3, EEP_SCK3. EEP_TXD3 MT_4.9V BACKLIGHT CONTROL IC4801 24 6 7 64k EEPROM (14/21) BACKLIGHT DRIVE BL_15V

D9001 BACKLIGHT CN8705 BL_H BL_L 6 5 2 1


BL_CONT Q4801, 4802 BEEP MODULATOR MELODY 227 233 232 103 105

MELODY ENV OVERALL (6/8) (PAGE 3-11)

249 237 154 238 260

27

EXT_MIC_JACK_IN ZOOM_MIC_CONT_V XMIC_MONO SHOE_STEREO

05

A : VIDEO SIGNAL



( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.RR-001 BOARD (3/4)Q2407 2409 88 3 90 BUFFER CN1003 (3/4) LNOY LNOPB LNOPR 2 4 6 XLINE_CNT1A, XLINE_CNT1B, XLINE_CNT2, 1 XLINE_CNT3A, XLINE_CNT3B 48 45 XD4CN 44 XPSV_D4 18 IC2401 COMPONENT OUT AMP, D-TERMINAL DRIVER (4/21) 35 33 31 D3_LNO_Y D3_LNO_PB D3_LNO_PR 56 55 52 51 49 47 48 24 25 28 29 31 33 32 CN9001 (3/4) CN9002 12 14 16 18 20 21 12 14 16 18 20 21

HH-001 BOARDCN101 Y PB PR CN105 1 3 5 6 8 10 COMPONENT OUT


22

XCS1_IC_2201 XCS2_IC_2201 LINE_OUT_VD IC_2201_HOSDVD

18 256 190 80

IC2201 (5/5)


43 LINE_CNT1 LINE_CNT3 41 40 D3CN

CTRL1 CTRL3

23

OSD_SO, XOSD_SCK, XCS_OSD OVERALL (7/8) (PAGE 3-14)

IC2402 1 3 4 HD-OSD CONTROL (4/21)

28

XSYS_RST

BASE BAND SIGNAL PROCESSOR, DOWN 19 IC_2201_HOSDHD CONVERTER 20 313 (4/21) IC_2201_COL_H0 8 IC_2201_COL_H3 83 85 16 315 317 14 IC_2201_OSDP_H, 15 IC_2201_OSDR, 314 IC_2201_ADAO1 IC_2201_OSDL_H 423 86 13 CK256FSO 82 11 186 IC_2201_CK14MFO 8 81 193 AUIN11

SW

LINE_IC_4401_Y LINE_IC_4401_C

10 7 IC4401

88 3 90

S_Y_I/O S_C_I/O VIDEO_I/O OVERALL (7/8) (PAGE 3-13) AUDIO_L_I/O AUDIO_R_I/O SP

S_Y_I/O S_C_I/O VIDEO_I/O

60 62 61 65 68 66

20 18 19 15 12 14

10 9 8 6 3 4

10 9 8 6 3 4

CN106 S_Y_I/O 10 S_C_I/O 5 VIDEO_I/O 9 JACK_AD AUDIO_L AUDIO_R 7 1 6 A/V OUT


14

CK64FSO SFD_LRCK XPWAD, XPWDA VSP_SO, XVSP_SCK

XPWAD, XPWDA

15 9 16 IC4601 11 AUDIO 10 AD/DA 12 CONVERTER 3 8 (13/21) 2 13 14

PBIN_L PBIN_R

VIDEO OUT, AUDIO IN/OUT (13/21) 31 57 30 61 70 74

29

MULTIJACK_AD

MULTIJACK_AD AUDIO_L_I/O AUDIO_R_I/O

RECOUT_L RECOUT_R

35 34

CN9006 SP 71 73 9 7 SP 2 1 SP9001 SPEAKER

VSP_SO, XVSP_SCK


20

XCS_IC_4401 XCS_AUVOL XEXT_MIC_ON HP_JACK_IN KASYAON BEEP EXT_MIC_JACK_IN ZOOM_MIC_CONT_V XMIC_MONO SHOE_STEREO

23 24 25

42 44

CN1008 (1/2) VOLOUT_L 8 VOLOUT_R 9 Q4401, 4403

CN8102 (1/2) 32 31 VOLOUT_L VOLOUT_R 8 5 10 7

75 77 65 78

MUTE SWITCH

34 33

6 7

HP_L_OUT HP_R_OUT

IC8403 MIC LEVEL CONTROL (2/2)


3 27


VSP_SO, XVSP_SCK XCS_AUVOL XEXT_MIC_ON HP_JACK_IN EXT_MIC_JACK_IN ZOOM_MIC_CONT_V XMIC_MONO SHOE_STEREO SHOE_MIC_FR SHOE_MIC_FL

19 18 17 5 36 3 2 4 1 14 12

21 22 23 35 4 37 38 36 39 26 28 EXT_MIC_JACK_IN ZOOM_MIC_CONT_V XMIC_MONO SHOE_STEREO G3 G5 H6 H3

VSP_SO, XVSP_SCK XCS_AUVOL XEXT_MIC_ON

12 13 3

CN9001 (1/2) OVERALL (8/8) (PAGE 3-16)

CN1002 (1/2) 2 3 MIC_FR MIC_FL 2 3

30

HOT SHOE (1/2)

IC8301

IC8402 (2/2) 7 6 5 1

FP-245 FLEXIBLE BOARD (1/2)J8502 (HEADPHONE) HP_R_OUT HP_L_OUT HP_JACK_IN EXT_IN_R EXT_IN_L 21 19 17

OO-001 BOARD (1/2)CN8101 (1/2) HP_R_OUT HP_L_OUT HP_JACK_IN SHOE_MIC_FR SHOE MIC_FL EXT_IN_R EXT_IN_L B2 B7 C1 C8 F1 F8

MIC AMP (2/2)

J8501 MIC (PLUG IN POWER)

24 26 IC8204 LPF DELAY (1/2) IC8205 LPF DELAY (1/2) IC8206 1 REVERSE AMP 6 7 (1/2) 2 xFRONT RIGHT xFRONT LEFT

H2 G6

R_OUT L_OUT 7 6

IC8401 (2/2) 1 5

MIC9001 MICROPHONE UNIT (R) (FRONT R) (REAR R) MIC9002 MICROPHONE UNIT (L) (FRONT L) 5 6 2 3 05 2 3 5 6

6 CN8501 MIC_FR MIC_RR 1 3 IC8201 7 REVERSE AMP 2 1 (1/2) 6

7

6

7

d-FRONT LEFT

d-FRONT RIGHT

2

1

2

1

IC8208 7 REVERSE AMP 2 1 (1/2) 6

INT_MIC_R INT_MIC_L

xREAR RIGHT CN8502 MIC_FL MIC_RL 7 5 IC8202 1 REVERSE AMP 6 7 (1/2) 2 xREAR LEFT

2 6

IC8203 LPF DELAY (1/2)

1 7

d-REAR RIGHT d-REAR LEFT

A : VIDEO SIGNAL A : AUDIO SIGNAL

(REAR L)


3-7. OVERALL BLOCK DIAGRAM (7/8)RR-001 BOARD (4/4) CONTROL KEY BLOCK (SB9000)T S8702 (ZOOM) W S8701 S8703 REC START/STOP 4

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.TT-001 BOARD (7/7) OO-001 BOARD (2/2)CN1008 (2/2) KEY_AD1-2 CN8102 CN8101 (2/2) (2/2) KEY_AD1-2

FP-245 FLEXIBLE BOARD (2/2)S8501 ASSIGN 12 S8502 NIGHTSHOT ON OFF

PP-001 BOARD (2/2)CN8702 KEY_AD2_5 (2ndZOOM_T) CN8701 (2/2) KEY_AD2-7 CN9004 (2/2) 27 1

S9003 AUTO LOCK ON OFF KEY_AD1-2

39

1

5

KEY_AD2_3 (2ndZOOM_W) CN9001 (4/4) KEY_AD2 CN1003 (3/3) 64 16 KEY_AD2

3

KEY_AD2(2nd_S/S)

26

2

FP-248 FLEXIBLE BOARDS001 (PANEL REVERSE) S002 PANEL OPEN/CLOSE 3

KEY AD0 KEY AD1 KEY AD2 KEY AD3 KEY AD4 KEY AD5 KEY AD6 SYS V XSYS_RST

CN9005 KEY_AD4 72 8 KEY_AD4

139 140 141 142 143 144 145 218 299

264

STROBE_LED

STROBE_LED

37

3

SCHARGE_LED

9

Q8501 LED DRIVE

D8501 (ASSIGN)

IC4802 (3/3) HI CONTROL (14/21) 100 102 OSD_SO, XOSD_SCK, XCS_OSD XSYS_RST IR_ON SHOE CONT

28


YY-001 BOARD (2/2)CN1006 (2/2) IR_ON CN9201 (2/2) CN9202 IR_ON

FP-247 FLEXIBLE BOARDQ001 LED DRIVE

5

KEY_AD5

71

9

KEY_AD5 X5202 10MHz

28 29 51

19 44 33 23 26

OSD_V XDS_RESET XHIDSCON_MAD

217 86 266 93 96

250 257

15

13

1

XF_TALLY_LED

9

19

XF_TALLY_LED

7

D004, 005 IR EMITTER /NIGHTSHOT D001 CAMERA RECORDING IC001 4 REMOTE SENSOR

CONTROL SWITCH BLOCK (CK12300)RV2401 EXPOSURE/VOL (ZOOM) S0002 BACK LIGHT S0003 EXPANDED FOCUS S0004 TELE MACRO S0005 EXPOSURE/VOL (ON/OFF) FOCUS MANUAL S0001 AUTO ZOOM KEY_AD3-5 KEY_AD3-6 8 9 BT9001 LITHIUM BATTERY 1 79 KEY_AD3-2 2 KEY_AD3 S9002 DSPLAY/ BATT INFO 3 S9001 RESET 77 2 78 KEY_AD3 CN9007 5 KEY_AD6 4 76 KEY_AD6

X5201 32.768kHz

52

IC_5201_TXD0, IC_5201_RXD0, IC_5201_SCK0, IC_5201XCS0

SIRCS_SIG XF_TALLY_LED SIRCS_SIG

4

24

SIRCS_SIG

10

16 41

7

KEY_AD3-3

6

XBATT_INFO_SW

6

KEY_AD3-4

3

6

74

HI_XRESET

73 HI_XRESET CN1002 (2/2) SHOE_CONT HOTSHOE_ID1, HOTSHOE_ID2 EXT_STROBE_ON HOTSHOE_ID1, HOTSHOE_ID2 EXT_STROBE LANC_SIG SHOE_UNREG CN9001 (2/2) 11 5 8 9 10 6 7 13 7 10 11 12 8 9 HOT SHOE (2/2)

LI_3V

LI_3V

54 55

CONTROL SWITCH BLOCK (PS12300)S1004 REC START/STOP S1002 (PHOTO FREEZE) PHOTO S1001 (PHOTO REC) S1003 (POWER) (MODE CHANGE) 4 3

NN-001 BOARD (4/4)CN7007 2 KEY_AD0 CN7009 (3/3) 40 39 CN1004 (3/3) KEY_AD0

31


IC5201 HI CONTROL (19/21)

13 14

KEY_AD1-2 KEY_AD1

15 16

14 15

KEY_AD1-2 KEY_AD1

POWER OFF (CHG) ON MODE>

XPOWER_SW XMODE_SW

48 50

47 49

XPOWER_SW XMODE_SW

1 2 77 BATT/XEXT ACV_UNREG, VTR_UNREG, ST-UNREG, SHOE_UNREG 37 FAST_CHARGE Q6003, 6004 11 38 INIT_CHARGE_ON Q6001, 6002

CN1007 16 1 7 9 15

FP-262 FLEXIBLE BOARDBATT/XEXT ACV_UNREG ACV_GND J1001 DC IN

D1002 CAMERA-TAPE D1004 CAMERA-MEMORY D1006 PLAY/EDIT D1010 CHG RV1001 W J1001 (LANC) (ZOOM) T

12

XCAM_LED

58

57

XCAM_LED

10

LF6001

11

XMEM_LED

7

6

XMEM_LED

10

XVTR_LED

60

59

XVTR_LED

12 Q5201 BATT_UNREG BATT_SIG BATTERY CHARGE DETECT

CN1009 1 7 9 10 16 ACV_UNREG A_1.5V D_1.5V_1 D_1.2V A_1.2V D_2.5V RP_2.8V A_2.8V EP_2.8V RP_4.6V A_4.6V AU_4.6V MT_4.9V D_2.8V D_1.5V_2 D_1.5V_3 PANEL_8V D4_-2.8V BL_-15V EP_13.5V EVER_3.0V VOUT LANC_DC BL_CONT OVERALL (5/8) (PAGE 3-9) OVERALL (4/8) (PAGE 3-7)

FP-261 FLEXIBLE BOARDBATT_UNREG BATT_SIG BATT_GND

7 17 21 LANC_SIG 22

XCHARGE_LED ZOOM_VR_AD XLANC_JACK_IN

8 41 62

7 40 61

XCHARGE_LED

+ S

9

42 43

BT1001 BATTERY TERMINAL

XLANC_JACK_IN

LI_3V 34

D2 B2

HI_XRESET

A3 K2 IC6001

FP-263 FLEXIBLE BOARDS002 (EJECT) 3 4

CN7010 XEJECT_SW

20 54

19 53

LANC_SIG XEJECT_SW 4 39 40 7 79

LANC_SIG

LANC_SIG

LANC_IN LANC_OUT XLANC_PWR_ON XLANC_ON

DC CONTROL, RESET, K3 LANC DRIVER (20/21) L3 L2 J4 E2 E3 A2 D1 E4 VO10B J9


5 12 19 15 29

ZOOM_VR_AD EXT_STROBE_ON INT_STROBE_ON XSYS_RST SYS_V XSYS RST

20 21 31 35 67

HI_EVER_SO, HI_EVER_SCK BATT_IN VTR_DD_ON XCS_MAIN_DD

XSYS_RST SYS_V

18 32

OVERALL (2/8) (PAGE 3-4) OVERALL (4/8) (PAGE 3-7) OVERALL (3/8) (PAGE 3-5) OVERALL (6/8) (PAGE 3-12)

XSYS RST XSYS RST XRST_PLL MULTIJACK_AD

BL_CONT Q6005, 6006

L9

XRST_PLL MULTIJACK_AD

36 56 5 VO10B XCC_DOWN

26 24

05


3-8. OVERALL BLOCK DIAGRAM (8/8)XM-002 BOARD


XK-001 BOARD XS-002 BOARDINPUT1 INPUT LEVEL LINE MIC MIC ATT CN201 (1/3) 12 CN200 INPUT1 XLR_48V_CH1 5 CN102 (2/3) 15 CH1_(+)_COM 2 CN201 (2/3) 5 6 3 2 7 1 6 5 CN201 (3/3) 5 12 5 CN301 (2/3) 15 CH2_(+)_COM 2 5 6 3 2 7 1 6 5 3 IC205 7 IC204 LOW CUT SELECTOR 7 IC300 MIC AMP 6 9 11 IC301 AMP/ V BIAS 7 9 8 6 CN301 (3/3) 14 CH2_SIG_OUT 3 HOTSHOE_ID2 4 10 HOTSHOE_ID1 3 7 CN101 (3/3) 14 CH1_SIG_OUT 3 INPUT1 REC CH SELECT CH1CH2 CH1 S102 5 MIC_FR 2 HOT SHOE TERMINAL CN102 (3/3) CN102 (1/3) S103 +48V OFF ON S100 2 LOW_CUT_ON_CH2 2 CN202 1 LOW_CUT_ON_CH1 1 S002 INPUT2 ON OFF CN001 S001 INPUT1 ON OFF LOW CUT

1 3 5 7

CH1_(+)_ATT CH1_(+)_THR CH1_()_ATT CH1_()_THR

16 14 12 10

IC200 MIC AMP

IC201 AMP/ V BIAS 7 11 14

CN103 7 MIC_FL 3

11 8 6

CH1_()_COM CH1_GAIN_HIGH CH1_GAIN_LINE

6 9 11

CN300 INPUT2

CN301 (1/3) 1 3 5 7 CH2_(+)_ATT CH2_(+)_THR CH2_()_ATT CH2_()_THR 16 14 12 10

CN101 (1/3)

30


CN101 (2/3)

LOW CUT 1 AMP

11 8 6

CH2_()_COM CH2_GAIN_HIGH CH2_GAIN_LINE

31SHOE_UNREG 2 SHOE_UNREG 8 9

12

XLR_48V_CH2


5 S104 LINE MIC MIC ATT INPUT LEVEL INPUT2 CN100 5 4 CH1_MIC48V CH2_MIC48V 9 10 CN401 IC401 DC/DC CONVERTER 6 7 SHOE_UNREG 8 7 S105 OFF ON

+48V

XD-002 BOARD

SHOE_UNREG

A : AUDIO SIGNAL

05


3-9. POWER BLOCK DIAGRAM (1/5)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.CN9001 F6006 Q6026, 6027 FB1002 CN1002 SHOE_UNREG 6 7 8 9 HOT SHOE

TT-001 BOARD (1/5) FP-262 FLEXIBLE BOARDJ1001 DC IN ACV_UNREG ACV_GND BATT/XEXT 1 7 9 15 16 CN1007 LF6001 Q6001, 6002 Q6003, 6004 F6005 BATT/XEXT CHARGE CONTROL F6002 F6003 F6004

G

POWER (5/5) (PAGE 3-25)

VTR_UNREG Q6007, 6017

D_2.8V D_1.5V_1

FP-261 FLEXIBLE BOARDBT1001 BATTERY TERMINAL

CN1009 1 7 9 10 16 F6001 BATT_SIG INIT_CHARGE_ON FAST_CHARGE BATT/XEXT BATT_SIG D6006 C1 VBAT2 D6005 IC6001 DC CONTROL, RESET, LANC DRIVER (20/21) HO2 B11 LO2 C10 VO2 A8 HO1 A9 LO1 A10 VO1 B8

L6008

L6020

SWITCHING L6016

A_1.5V

A_1.5V D_1.2V

+ S

BATT_UNREG BATT_SIG BATT_GND

D_1.5V_1

A_1.2V A_2.8V

APOWER (2/5) (PAGE 3-19)

Q6014, 6018 SWITCHING

L6004

L6015 L6021

A_1.2V D_1.2V

D_2.5V D_1.5V_3 MT_4.9V AU_4.6V

Q6008, 6019 SWITCHING HO3 C9 LO3 D10 VO3 D7 Q6009, 6020 SWITCHING HO4 D9 LO4 E11 VO4 D5 Q6010, 6021 SWITCHING HO5 E10 LO5 E8 VO5 A5

L6009

L6022

D_2.5V

D_1.5V_2 A_4.6V

L6026 L6024 L6005 L6019

RP_2.8V A_2.8V EP_2.8V

D4_2.8V

A_4.6V D_2.8V

L6027 L6025 L6010 L6023

RP_4.6V A_4.6V AU_4.6V

MT_4.9V EVER_3.0V LANC_DC EP_13.5V EP_2.8V VTR_UNREG

BPOWER (3/5) (PAGE 3-21)

IC5201 HI CONTROL (19/21) BATT_EXT 77 FAST_CHARGE 37 INIT_CHARGE 38

FB5203

VOUT

D3 VOUT PVCCL1 C8 CDET A4 HO6 F10 LO6 F8 VO6 K4 Q6011, 6022 SWITCHING IC6004 2.8V REG (20/21) 2 VIN Q6025 D6013 L6001 D6012 Q6016 SWITCHING D6008 L6003 PANEL_8V VO 5 D4_2.8V PANEL_8V A_4.6V EP_2.8V BL_CONT MT_4.9V L6012 VLCD G2 PVCCH F11 Q6012, 6023 D_2.8V BL_15V L6011 L6014 LI_3V D_2.8V A_2.8V AU_4.6V L6018 Q6013, 6024 SWITCHING HO8 G8 LO8 H10 VO8 H7 Q6015 L6007 L6017 D_1.5V_2 D_1.5V_3 A_4.6V A_2.8V MT_4.9V L6013 BL_15V L6006 RP_2.8V MT_4.9V RP_4.6V

BATT/XEXT FAST_CHARGE INIT_CHARGE_ON Q5201 BATTERY CHARGE DETECT SHOE_ON

D6009

IB_SO 42 IB_SI 43

BATT_SIG

PVCCL2 K11 VBATP K10 SWVO9 J11 DRV9 H9 VO9 H8

SHOE_ON 57 BATT_SENSE 65 ACV_SENSE 66

CPOWER (4/5) (PAGE 3-23)

FR_EVER_SO 20 FR_EVER_SCK 21 BATT_IN 31 VTR_DD_ON 35 XCS_DD 67 BATT_IN VTR_DD_ON XCS_MAIN_DD

HI_EVER_SO, HI_EVER_SCK

E2 DIN E3 CLK A2 OUTC1 D1 CTL E4 LD HO7 G11 LO7 G9 VO7 J5

SWITCHING

DPOWER (5/5) (PAGE 3-25)

XLANC_POWER_ON 7 XLANC_ON 79

XLANC_PWR_ON XLANC_ON

L2 WAKEUP J4 XCTL2 DRV10 J10 INM10 L9 VO10B J9 VOUT2 J1 LANC DC J2 VRO C2 VCH B2 VBATT D2

SWITCHING

BL_CONT Q6005, 6006 EMERGENCY DETECT EP_13.5V LANC_DC EVER_3.0V LI_3V

05


3-10.POWER BLOCK DIAGRAM (2/5)TT-001 BOARD (2/5)D_2.8V D_1.5V_1 A_1.5V D_1.2V A_1.2V A_2.8V D_2.8V D_1.5V_1 A_1.5V D_1.2V A_1.2V A_2.8V


D_2.8V D_1.5V_1 A_1.5V D_1.2V

D_1.5V_1 D_1.2V

FB1401

FB1403

L1404

FB1601

FB1602

L1201

IC1201 CDS, A/D CONVERTER (1/21)

L1202

IC1401 CAMERA SIGNAL PROCESSOR (2/21)

IC1403 CLOCK GENERATOR (2/21)

IC1402 128M SDRAM (2/21)

IC1601 JPEG ENCODER, MS SIGNAL PROCESSOR (3/21)

IC1801 128M SDRAM (3/21)

AFB2604 FB2605IC2607 HDV-MPEG VIDEO ENCODER (5/21)

FB2801

FB2602

FB3204

FB3203

FB3201

FB3202

FB3001

FB3402

FB5001

IC3201 HDV-MPEG VIDEO DECODER (7/21)

IC3001, 3002 128M SDRAM (6/21)

IC3401, 3402 128M SDRAM (8/21)

IC5001 64M SDRAM (15/21)

IC2001 BUS BRIDGE (15/21)

FB2001

IC2801 2806 BUFFER (5/21)

IC2604 AND GATE (5/21)

IC2606 BUFFER (5/21)

IC2605 LEVEL SHIFTER (5/21)

FB2601

D_1.5V_3

IC2603 OR GATE (5/21)

IC2601 D-FFs (5/21)

FB2603

POWER (1/5) (PAGE 3-18)

D_2.5V

D_2.5V D_2.8V D_1.5V_3

D_2.5V D_2.8V

FB1801

IC2602 BUFFER (5/21)

Q4402 MT_4.9V AU_4.6V D_1.5V_2 AU_4.6V D_1.5V_2 D_2.8V A_2.8V A_4.6V D4_2.8V D_1.5V_1 AU_4.6V D_1.5V_2 D_2.8V A_2.8V A_4.6V D4_2.8V AU_4.6V D_2.8V A_2.8V A_4.6V 3.2V REG

A_4.6V D4_2.8V

FB3602

FB3601

FB3801

FB3802

FB3803

FB4001

FB2402

FB4401

L4002

L4003

L4004

L4005

L4006

L4007

L2403

L2401

L2402

L2202

L2205

L2207

L2208

L2210

L2201

L2203

L4601

L4401

L4402

L4406

L4405

IC3601 MPEG AUDIO SIGNAL PROCESSOR (9/21)

IC3801 HDV STREAM PROCESSOR (10/21)

IC4001 DV SIGNAL PROCESSOR (11/21)

IC2401 COMPONENT OUT AMP, D-TERMINAL DRIVER (4/21)

IC2402 HD-OSD CONTROL (4/21)

IC2201 BASE BAND SIGNAL PROCESSOR, DOWN CONVERTER (4/21)

IC4601 AUDIO AD/DA CONVERTER (13/21)

IC4401 VIDEO OUT, AUDIO IN/OUT (13/21)

IC4804 1.9V REG (14/21) D_2.5V IC4805 3.1V REG (14/21) A_4.6V A_2.8V D_2.8V D_1.5V_1 D_1.2V 5 VI VO 4 D_3.1V A_2.8V D_2.8V D_1.2V Q4803 4805 D_2.8V CHIME_VDD XREEL_HALL_ON 5 VI VO 4 D_1.9V D_1.9V

L4404

EPOWER (3/5) (PAGE 3-21)

FB4202

FB5801

FB5802

FB5601

FB4803

FB4802

FB4805

FB4201

FB5401

L4203

MS_VCC_ON

FPOWER (4/5) (PAGE 3-23)

IC5802 CAMERA CONTROL (16/21)

IC5801 64K EEPROM (16/21)

IC5601 HDV-LSI CONTROL (18/21)

IC4801 64K EEPROM (14/21)

IC4803 OSCILLATOR DRIVE (14/21)

IC4802 DS CONTROL, HI CONTROL, FLASH (14/21)

IC4201 HDV/DV i.LINK INTERFACE (12/21)

IC5402 32K EEPROM (17/21)

IC5401 MECHA CONTROL (17/21) XREEL_HALL_ON 153

CHIME_PWR_CNT 130 MS_VCC_ON 276 05


3-11.POWER BLOCK DIAGRAM (3/5)TT-001 BOARD (3/5)CN1004 A_4.6V 31 33 22 26 8 10 12 32 34 23 27 9 11 13


NN-001 BOARDCN7009 A_4.6V L7203 5 VIN VO 4 D_2.8V IC7202 2.8V REG (1/5)

YY-001 BOARD (1/2)CN7006 Z_MR_VCC F_MR_VCC CN9206 18 20 16 14 CN9205 Z_MR_VCC F_MR_VCC 18 20

LENS BLOCKZOOM MR FOCUS MR

D_2.8V

D_2.8V

MT_4.9V

MT_4.9V

L7002

L7201

MT_4.9VFB7201

CONTROL SWITCH BLOCK (PS12300)IC7205 FOCUS MOTOR NOISE FILTER (1/5) IC7203, 7204 ZOOM MOTOR NOISE FILTER (1/5) IC7201 FOCUS/ZOOM MOTOR DRIVE, ND FILTER DRIVE, IRIS DRIVE (1/5) CN7007 D_2.8V RV1001 16 T W (ZOOM) MODE_LED_VDD CHARGE_LED_VDD 9 6 D1010 CHG D1002 TAPE D1004 MEMORY D1006 PLAY/EDIT FB1003 18 J1001 (LANC) CAMERA

BPOWER (1/5) (PAGE 3-18) EVER_3.0V 21 22 EVER_3.0V EVER_3.0V LANC_DC LANC_DC LANC_DC

20

21

LANC_DC

UU-001 BOARDIC7602 6V REG (2/5) 5 Vi EP_13.5V EP_2.8V 35 37 32 34 9 11 13 36 38 27 29 36 38 33 35 10 12 14 37 39 28 30 EP_13.5V EP_2.8V Vo 4 EP_13.5V EP_2.8V Q7801, 7802L7801 L7802

CN7801 MT_4.9V L7803 EVF_4.9V EVF_13.5V 7 8 10 20 21 18

CN9803 L9801 CN9802 EP_13.5V

LCD9002

1

COLOR EVF UNIT

VTR_UNREG

VTR_UNREG

IC9801 EVF BACKLIGHT CONTROL D9801 (EVF BACKLIGHT)

RP_2.8V RP_4.6V

RP_2.8V RP_4.6VL7602 L7601

IC7801 EVF DRIVER (4/5)

IC7802 TIMING GENERATOR (4/5) XSTBY 25

IC7601 REC/PB AMP (2/5) CN1001 CHIME_VDD 41 42 CN7008 CHIME_VDD CN7002 CHIME_VDD 12

N MECHA DECK (MDX-N101)MIC9003 4PIN CONNECTOR S REEL SENSOR H9001 SENSOR_VCC HALL_VCC 21 T REEL SENSOR H9002

EPOWER (2/5) (PAGE 3-20) XREEL_HALL_ON 39 40 XREEL_HALL_ON EP_13.5V MT_4.9V TAPE_LED_A 26 Q7401 D_2.8V

LED9001 TAPE LED

EVER_3.0VL7401

VTR_UNREG

IC7001 CAPSTAN PWM DRIVE (3/5)

IC7002 DRUM PWM DRIVE (3/5)

IC7401 DRUM/ CAPSTAN/ LOADING MOTOR DRIVE (3/5) VH 17 VMR 3 MR_VCC CN7004 HE_VCC FG_VCC 8 25 26 HU, HV, HW CAPSTAN FG

05


3-12.POWER BLOCK DIAGRAM (4/5)TT-001 BOARD (4/5)PANEL_8V A_4.6V EP_2.8V CN1003 PANEL_8V 12 A_4.6V 11 EP_2.8V 10

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.RR-001 BOARDCN9001 PANEL_8V 68 A_4.6V 69 EP_2.8V 70 CN9004 PANEL_8V 20 A_4.6V 21 EP_2.8V 22

PP-001 BOARDCN8701 PANEL_8V 8 A_4.6V 7 EP_2.8V 6 L8704 Q8710, 8712 CN8704 VDD 18

LCD9001 2.7 inch WIDE COLOR LCD UNIT

FB8701

L8701

L8702

IC8701 LCD DRIVER

XSTBY 11 EXTDA 34 PWM 20

Q8708, 8709 BACKLIGHT CONTROL Q8706, 8707 CN8705 BL_H 5 6 D9001 BACKLIGHT

BL_CONT MT_4.9V D_2.8V BL_15V LI_3V

BL_CONT MT_4.9V D_2.8V BL_15V LI_3V

17 14 15 13 79

63 66

BL_CONT MT_4.9V

BL_CONT MT_4.9V D_2.8V BL_15V

17 18 3 4

11 10

BL_CONT MT_4.9V L8703

BACKLIGHT DRIVE

D_2.8V 65 BL_15V 67 1 LI_3V

D_2.8V 25 BL_15V 24

BL_L

1 2

CPOWER (1/5) (PAGE 3-18)

CONTROL SWITCH BLOCK (CK12300)BT9001 LITHIUM BATTERY CN9007 D_2.8V RV2401 4 EXPOSURE/VOL (ZOOM)

OO-001 BOARDCN1008 A_2.8V A_2.8V 22 24 27 29 CN8102 16 A_2.8V 18 11 AU_4.6V 13 L8101 CN8101 A_2.8V 10 11

FP-245 FLEXIBLE BOARD

D8501 (ASSIGN)

AU_4.6V

AU_4.6V

IC8201, 8202, 8206, 8208 REVERSE AMP (1/2)

IC8203 8205 LPF DELAY (1/2)

IC8207 VOLTAGE FOLLOWER (1/2)

IC8403 MIC LEVEL CONTROL (2/2)

IC8401, 8402 MIC SELECTION SWITCH (2/2)

MIC AMP (2/2)

AOUT 1 BOUT 2

A2.3V A2.3V

WW-001 BOARDCN1011 A_4.6V CN301 A_4.6V CN302 MS_VCC MEMORY STICK DUO

10

10

5

IC301 2.9V REG 1

4

9

FPOWER (2/5) (PAGE 3-20)

MS_VCC_ON

MS_VCC_ON

8

8

MS_VCC_ON

D_2.8V 05

13

13

D_2.8V

D301 (MS ACCESS)


L8301IC8301

L8102

3-13.POWER BLOCK DIAGRAM (5/5)TT-001 BOARD (5/5)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.YY-001 BOARD (2/2)CN1006 CN9201 5 6 7 8 10 11 22 A_4.6V 23 20 A_2.8V 21 17 MT_4.9V 18

FP-247 FLEXIBLE BOARDIC001 9 REMOTE SENSOR D001 CAMERA RECORDING D004, 005 IR EMITTER NIGHTSHOT

A_4.6V

A_4.6V

CN9202 A_4.6V

DPOWER (1/5) (PAGE 3-18)

A_2.8V

A_2.8V

A_2.8V

8

MT_4.9V

MT_4.9V

MT_4.9V

5 6

FP-246 FLEXIBLE BOARDA_4.6V 24 4 A_4.6V CN9204 A_4.6V 3 PH001, 002 MANUAL FOCUS/ ZOOM SENSOR

EE-001 BOARDCN1013 A_4.6V 16 17 CN6401 16 A_4.6V 17 IC6404 1.8V REG L009 5 IN OUT 4

IC6403 3.3V REG L008 5 IN OUT 4 L010 IC6402 3.3V REG 5 IN OUT 4 L006 L011 IC6601 2.8M CMOS IMAGER

IC6401 2.8V REG L007 5 IN OUT 4

A_2.8V

21

21

A_2.8V

L6801

IC6801 PITCH/YAW SENSOR AMP SE6801 YAW SENSOR SE6802 PITCH SENSOR

IC6406, 6407 BUFFER

INPUT1 LINE MIC +48V ON OFF MIC ATT S103 CN102 5 12 INPUT LEVEL

XM-002 BOARDIC204 LOW CUT SELECTOR CN201 XLR_48V_CH1 IC205 LOW CUT AMP

CN200 INPUT1

XS-002 BOARD

XD-002 BOARDCN401 (1/2) 6 7 8 7 L400 Q404 - 407, 409 411 IC401 DC/DC CONVERTER 1 SWITCH Q408 L401 D402 L402 Q402 CN401 (2/2) CH1_MIC48V CN100 (2/2) 9 5

GPOWER (1/5) (PAGE 3-18)

HOT SHOE TERMINAL

8 9

2

CN103 SHOE_UNREG

CN100 (1/2)

A_4.6V

L203 4 13

A_4.6V

Q403 CH2_MIC48V 10 4 IC200 MIC AMP IC201 AMP/ V BIAS IC203 V BIAS

4 IC402 5V REG

L403 2 IN OUT 3

AU_4.6V

6 5

8 9 INPUT2 LINE MIC +48V ON OFF MIC ATT S104

CN101 A_4.6V

CN301 4 13

L303

A_4.6V

IC300 INPUT LEVEL MIC AMP

IC301 AMP/ V BIAS

IC303 V BIAS CN300 INPUT2

5 05

12

XLR_48V_CH1

HVR-A1J/A1U/A1N/A1E/A1P/A1C 3-25 3-26E

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS4-1. FRAME SCHEMATIC DIAGRAMSFLAME SCHEMATIC DIAGRAM (1/2) FP-246 FLEXIBLE BOARDMANUAL FOCUS/ ZOOM SENSOR FP-032 FLEXIBLE BOARD FP-228 FLEXIBLE BOARDM9002 LOADING MOTOR

FP-247 FLEXIBLE BOARDREMOTE SENSOR, IR EMITTER10 8 9 10P GND XEVEN YEVEN

VIDEO HEAD (ODD, EVEN)

M9001 DRUM MOTOR

FP-031 FLEXIBLE BOARD

N MECHANISM DECK (MDX-N101)M9003 CAPPSTAN MOTOR

CN7801

27P COM VR VG VB 27 26 25 24 23 22 21 1 2 3 4 5 6 7

CN9803 COM VR VG VB

27P

CN9802 18P COM PSIG G R B N.C. HCK1 HCK2 HST RGT DWN EN STB VCK VST PCG VSS EP_13.5V 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

REG_GND HCK1 REG_GND HCK2 HST

REG_GND HCK1 REG_GND HCK2 HST RGT DWN EN STB VCK VST REG_GND REG_GND EVF_13.5V REG_GND EVF_4.9V EVF_4.9V REG_GND REG_GND LED_DA LED_ON/OFF PCG PSIG

FP-260 FLEXIBLE

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

29

28

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

27

26

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

10

RGT9 8 7 6 5 4 3 2 1

1

2

3

4

5

6

7

8

9

8

7

6

5

4

3

2

7

6

5

4

3

2

1

9

1

LCD9002 COLOR EVF UNIT

CN7002 29P

CN7001 10P

XSDL (N.C.)

YSDL (N.C.)

GND

DRUM_W

CHIME_SDA

27P

DWNCAP_V VHE+ CAP_V CAP_U CAP_U CAP_W CAP_U CAP_V CAP_V UHEFG_GND FG_GND CAP_U HE_VCC CAP_W CAP_W WHE+ UHE+ HE_GND FG_VCC FG1 FG2 CAP_W FG_VCC WHEVHEN.C

GND

YODD

XODD

GND

DRUM_W

SREEL-

XREC_PROOF

XMODE_SW_A

DRUM_V

FG/PG_COM

DRUM_V

HALL_GND

MIC/REC_SW_GND

SW_COM

DRUM_U

SREEL+

TREEL-

DEW+

XCCDOWN_SW

TOP/END_GND

LM_UNLOAD

LM_UNLOAD

FG

DRUM_U

NC

CHIME_SCK

Cin_GND

CHIME_VDD

HALL_VCC

XMODE_SW_C

XMODE_SW_B

TAPE_LED_A

TAPE_END

TAPE_LED_K

TAPE_TOP

LM_LOAD

LM_LOAD

PG

M_COM

TREEL+

DEW-

CN7010 6P

EN STB VCK VST REG_GND REG_GND EVF_13.5V REG_GND EVF_4.9V EVF_4.9V

SIRCS_SIG

REG_GND

REG_GND

REG_GND

XF_TALLY_LED

REG_GND

MT_4.9V

MT_GND

MT_GND

MT_4.9V

MF_LED

CN9204

CN9202

FP-263 FLEXIBLE(EJECT SWITCH)CN9206 33P I_DRIVEI_BIAS+ I_HALL+ I_BIASI_HALLNC_GND I_DRIVE+ ND_DRIVEND_BIASND_HALL33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

1 2 3 4 5 6

REG_GND NC XEJECT_SW XEJECT_SW NC REG_GND

6P

MF_B

MF_A

A_4.6V

12P

A_2.8V

A_4.6V

IR_ON

N.C.

CN7003

CN7004

10

11

12

1

2

3

4

5

6

7

8

1

2

3

4

5

6

9

CN9205 33P 1 2 3 I_DRIVEI_BIAS+ I_HALL+ I_BIASI_HALLNC_GND I_DRIVE+ ND_DRIVEND_BIASND_HALLND_BIAS+ ND_HALL+ NC_GND ND_DRIVE+ Z_MR_GND Z_MR_A Z_MR_B Z_MR_VCC F_MR_B F_MR_VCC F_MR_AF_MR_GND/TEMP_GND

CN7006 1 2 3 4 5 6 7 8 9 10 11

33P

REG_GND REG_GND LED_DA LED_ON/OFF PCG PSIG CN7007 22P 2 4 6 8 REG_GND RF_IN REG_GND VD_SI XVD_SCK XCS_EVF VD_SO MODE_SW_A MODE_SW_B MODE_SW_C DEW_DET REG_GND DRUM_PWM REG_GND CAP_PWM REG_GND XRST_VTR LM_LIM_DET LOAD XREEL_HALL_ON CHIME_VDD CHIME_SDA REG_GND REG_GND RECCK REG_GND RECDT RECA1 RECA2 ND_HALL_AD REG_GND REG_GND CAM_SO CAM_SI DIRB1 DIRA1 EN1 REG_GND PNDCK REG_GND NC REG_GND REG_GND REG_GND XCS_IC_7401 VSP_SO XVSP_SCK TAPE_LED_ON TAPE_TOP TAPE_END CAP_FG SREEL_FG TREEL_FG CONT1 DRUM_PG DRUM_FG CAP_FWD CAP_ON REC_PROOF UNLOAD REG_GND CHIME_SCK REG_GND CK13MFO2 REG_GND REG_GND LENS_TEMP_AD ALL_PS SW_PS I_HALL_AD REG_GND CAM_SCK REG_GND CAM_VD NF_SW NF_EN XCS_IC_7201 XRST_IC_7201 REG_GND REG_GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 7180P

I_DRIVEI_BIAS+ I_HALL+ I_BIASI_HALLNC_GND I_DRIVE+ ND_DRIVEND_BIASND_HALLND_BIAS+ ND_HALL+ NC_GND ND_DRIVE+ Z_MR_GND Z_MR_A Z_MR_B Z_MR_VCC F_MR_B F_MR_VCC F_MR_AF_MR_GND/TEMP_GND

UU-001 BOARDEVF, EVF BACKLIGHT

LENS BLOCK

4 5 6 7 8 9 10 11 12 13 14

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

MT_GND MT_GND MT_GND XCHARGE_LED VTR_UNREG VTR_UNREG VTR_UNREG KEY_AD1 REG_GND LANC_SIG EVER_3.0V D_2.8V D_2.8V RP_4.6V RP_4.6V A_4.6V A_4.6V EP_13.5V EP_13.5V KEY_AD0 REG_GND REG_GND REG_GND XPOWER_SW XMODE_SW XCC_DOWN XEJECT_SW VO10B XCAM_LED XVTR_LED XLANC_JACK_IN REG_GND EVBL EVGR EVRE REG_GND XEVD XEHD FRRV REG_GND

NC REG_GND REG_GND XMEM_LED MT_4.9V MT_4.9V MT_4.9V KEY_AD1-2 REG_GND REG_GND LANC_DC D_2.8V D_2.8V D_2.8V A_2.8V A_2.8V EP_2.8V EP_2.8V RP_2.8V RP_2.8V ZOOM_VR_AD REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND XFFREW_UP SWP REC_CRRT0 REC_CRRT1

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

LANC_SIG XLANC_JACK_IN REG_GND REG_GND LANC_DC ZOOM_VR_AD D_2.8V REG_GND KEY_AD1 KEY_AD1-2 XCAM_LED XMEM_LED XVTR_LED MODE_LED_VDD REG_GND XCHARGE_LED CHARGE_LED_VDD REG_GND XPOWER_SW XMODE_SW KEY_AD0 REG_GND CN7005 16P

22 21 20 19 18 17 16 15 14 13 12 11 10 9(REAR R) 2 3 4 5 MIC_RR 4 3 6 5 MIC_GND MIC_RR 2 MIC_GND MIC_RR MIC_FR 1 MIC_GND MIC_FR MIC_GND MIC_RL 6 (REAR L)

FP-264 FLEXIBLE

EE-001 BOARD(CMOS IMAGER)36 37 38 39 31 32 33 34 35

15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

YY-001 BOARD(CONNECTION BOARD)

ND_BIAS+ ND_HALL+ NC_GND ND_DRIVE+ Z_MR_GND Z_MR_A Z_MR_B Z_MR_VCC F_MR_B F_MR_VCC F_MR_AF_MR_GND/TEMP_GND

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

NN-001 BOARD(1/5) (LENS DRIVE) (2/5) (REC/PB AMP) (3/5) (SERVO) (4/5) (EVF DRIVE) (5/5) (CONNECTOR)

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60

CONTROL SWITCH BLOCK (PS12300)MIC9002 MICROPHONE UNIT(L)(FRONT L)

MIC9001 MICROPHONE UNIT(R)(FRONT R)

8 7 6 5 4 3 2 16

TEMP_OUT FOCUS+ FOCUSNF_DRIVE+ NF_DRIVE+ NF_DRIVENF_DRIVEZOOM_AXF_TALLY_LED CN9201 27P SIRCS_SIG

TEMP_OUT FOCUS+ FOCUSNF_DRIVE+ NF_DRIVE+ NF_DRIVENF_DRIVEZOOM_A ZOOM_BREG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND MT_GND MT_GND MT_4.9V MT_4.9V MF_LED A_4.6V REG_GND REG_GND REG_GND

TEMP_OUT FOCUS+ FOCUSNF_DRIVE+ NF_DRIVE+ NF_DRIVENF_DRIVEZOOM_A ZOOM_B ZOOM_XA ZOOM_XB

5

4

3

2

D_1.5V_1 (N.C.)

30DRVOUT_GR1 DRVOUT_GR2 DRVOUT_GB1 DRVOUT_GB2 DCOUT_GR1 DCOUT_GR2 DCOUT_GB1 DCOUT_GB2 DRVOUT_R DRVOUT_B

NC NC REC_CRRT0 REC_CRRT1 FRRV SWP REG_GND RF_MON REG_GND REG_GND PSIG EVF_VG EVF_VCO EXT_DA REG_GND EVF_COM_DC

16CN8501 6P 6P MIC_GND MIC_GND MIC_GND 8 MIC_GND MIC_RL MIC_RL MIC_FL

39P

VST_C_RESET

D_2.8V (N.C.)

1

1 11 10 9 A_2.8V A_2.8V SCHARGE_LED MIC_FL 7

31REG_GND DCOUT_B

ZOOM_B ZOOM_XA ZOOM_XB

15 14 13 12 11 10 CPC 9 8 7 6 5 4 3 2 1 (FOR CHECK)

XSYS_RST

PITCH_AD

REG_GND

REG_GND

DCOUT_R

AHS_SCK

XCS_AHS

CN6401

YAW_AD

AHS_SO

A_4.6V

A_4.6V

A_2.8V

A_2.8V

A_4.6V

A_4.6V

A_2.8V

32CHCK

ZOOM_XA ZOOM_XB

TGHD

IR_ON

MF_B

TGVD

27

26

25

24

23

22

21

20

19

18

17

16

N.C.

33

15

14

13

12

11

30

29

28

14

27

24

23

21

17

15

13

12

11

22

20

26

25

19

18

16

10

10

9

8

7

6

5

MF_A

4

3

2

8

9

7

6

5

HARNESS (COAXIAL CABLE)25 26 19 18 13 12 22 20 16 10 27 24 23 21 17 30 29 28 15 14 11 4 3 2 1 2 3 4 5 6 7 8 9 5 8 7 6 1 D_2.8V (N.C.) D_1.5V_1 (N.C.) 39P VST_C_RESET 27P SIRCS_SIG A_4.6V A_4.6V A_2.8V A_2.8V REG_GND REG_GND REG_GND XSYS_RST DRVOUT_R DCOUT_R DRVOUT_GB1 DCOUT_GR1 A_4.6V DCOUT_GB1 DCOUT_GR2 TGHD A_4.6V CHCK TGVD DCOUT_GB2 DRVOUT_GB2 AHS_SO REG_GND PITCH_AD DRVOUT_GR2 DRVOUT_B A_2.8V DRVOUT_GR1 REG_GND REG_GND AHS_SCK XCS_AHS DCOUT_B YAW_AD

4

3

2

1

FP-256 FLEXIBLE10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 9 MT_4.9V MT_4.9V MT_GND MT_GND IR_ON A_4.6V REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND MF_LED N.C. MF_B MF_A REG_GND XF_TALLY_LED REG_GND

1

62

FP-261 FLEXIBLE BOARDBATTERY TERMINAL

BT1001 (BATTERY TERMINAL)

FP-262 FLEXIBLE BOARD80P

CN8502

MIC_FL

64 66 68 70 72 74 76 78 80

CN1013

CN1006

(DC IN)

J1001 DC IN

73 75 77 79

FP-245 FLEXIBLE BOARD(MIC, JACK)

CN7008

27

26

25

24

23

22

21

19

18

17

16

15

14

13

10

11

12

13

14

15

16

15

14

13

12

11

10

16

35CN1009 16P

CN1001 80P

80P

CN8101 27P

ACV_GND

ACV_GND

ACV_GND

ACV_GND

ACV_GND

ACV_GND

ACV_GND

MIC_GND

MIC_GND

HP_GND

HP_GND

EXT_IN_L

MIC_GND

HP_GND

REG_GND

ACV_UNREG

ACV_UNREG

ACV_UNREG

EXT_IN_R

REG_GND

ACV_UNREG

ACV_UNREG

ACV_UNREG

ACV_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

BATT_UNREG

CN1008 39P SHOE_STEREO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 39 38 37 36 35 34 33 32 31 30 29 28 27 26

CN8102 39P SHOE_STEREO ZOOM_MIC_CONT_V EXT_MIC_JACK_IN XMIC_MONO XEXT_MIC_ON MIC_GND MIC_GND VOLOUT_L VOLOUT_R MIC_GND MIC_GND SHOE_MIC_FL MIC_GND SHOE_MIC_FR MIC_GND MIC_GND XCS_AUVOL XVSP_SCK VSP_SO REG_GND REG_GND A_2.8V A_2.8V A_2.8V REG_GND REG_GND AU_4.6V AU_4.6V AU_4.6V REG_GND REG_GND REG_GND HP_R_OUT HP_L_OUT REG_GND HP_JACK_IN SCHARGE_LED NC KEY_AD1-2

CN1007

38 37 36

33 32 31

3 5 7 9 11 13

RF_IN REG_GND VD_SI XVD_SCK XCS_EVF VD_SO MODE_SW_A MODE_SW_B MODE_SW_C DEW_DET REG_GND DRUM_PWM REG_GND CAP_PWM REG_GND XRST_VTR LM_LIM_DET LOAD XREEL_HALL_ON CHIME_VDD CHIME_SDA REG_GND REG_GND RECCK REG_GND RECDT RECA1 RECA2 ND_HALL_AD REG_GND REG_GND CAM_SO CAM_SI DIRB1 DIRA1 EN1 REG_GND PNDCK REG_GND

REG_GND REG_GND XCS_IC_7401 VSP_SO XVSP_SCK TAPE_LED_ON TAPE_TOP TAPE_END CAP_FG SREEL_FG TREEL_FG CONT1 DRUM_PG DRUM_FG CAP_FWD CAP_ON REC_PROOF UNLOAD REG_GND CHIME_SCK REG_GND CK13MFO2 REG_GND REG_GND LENS_TEMP_AD ALL_PS SW_PS I_HALL_AD REG_GND CAM_SCK REG_GND CAM_VD NF_SW NF_EN XCS_IC_7201 XRST_IC_7201 REG_GND REG_GND NC

4CN1004

3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

MT_GND MT_GND XCHARGE_LED VTR_UNREG VTR_UNREG VTR_UNREG KEY_AD1 REG_GND LANC_SIG EVER_3.0V D_2.8V D_2.8V RP_4.6V RP_4.6V A_4.6V A_4.6V EP_13.5V EP_13.5V KEY_AD0 REG_GND REG_GND REG_GND XPOWER_SW XMODE_SW XCC_DOWN XEJECT_SW VO10B XCAM_LED XVTR_LED XLANC_JACK_IN REG_GND EVBL EVGR EVRE REG_GND XEVD XEHD FRRV REG_GND

REG_GND XMEM_LED MT_4.9V MT_4.9V MT_4.9V KEY_AD1-2 REG_GND REG_GND LANC_DC D_2.8V D_2.8V D_2.8V A_2.8V A_2.8V EP_2.8V EP_2.8V RP_2.8V RP_2.8V ZOOM_VR_AD REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND XFFREW_UP SWP REC_CRRT0 REC_CRRT1 NC

4 6 ZOOM_MIC_CONT_V 8 EXT_MIC_JACK_IN 10 XMIC_MONO 12 XEXT_MIC_ON 14 MIC_GND 16 MIC_GND 18 VOLOUT_L 20 VOLOUT_R 22 MIC_GND 24 MIC_GND 26 SHOE_MIC_FL 28 MIC_GND 30 SHOE_MIC_FR

6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80

CN1012 20P 15 1 2 3 4 5 6 7 8 9 (Not Use) 10 11 12 13 14 15 16 17 18 19 20 ST_GND 17 ST_GND 19 ST_GND 21 ST_GND ST_GND ST_GND ST_GND STROBE_ON XSCHARGE_FULL SCHARGE_ON STUNREG STUNREG STUNREG STUNREG STUNREG STUNREG PLUNGER MT_4.9V MT_4.9V XSTROBE_READY

TT-001 BOARD(1/21) (2/21) (3/21) (4/21) (5/21) (6/21) (7/21) (8/21) (9/21) (10/21) (11/21) (12/21) (13/21) (14/21) (15/21) (16/21) (17/21) (18/21) (19/21) (20/21) (21/21) (A/D CONVERTER) (CAMERA SIGNAL PROCESS) (MS SIGNAL PROCESS) (BASE BAND SIGNAL PROCESS) (HDV-MPEG VIDEO ENCODE) (SDRAM (VIDEO ENCODE)) (HDV-MPEG VIDEO DECODE) (SDRAM (VIDEO DECODE)) (MPEG AUDIO SIGNAL PROCESS) (HDV STREAM PROCESS) (DV SIGNAL PROCESS) (HDV/DV i.LINK INTERFACE) (VIDEO OUT,AUDIO IN/OUT) (DS CONTROL,HI CONTROL) (SDRAM (DIGITAL STILL)) (CAMERA CONTROL) (MECHA CONTROL) (HDV-LSI CONTROL) (HI CONTROL) (DC/DC CONVERTER) (CONNECTOR)80P

23 79 77 75 73 71 69 67 65 63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 LI_3V XBATT_INFO_SW REG_GND SPSP+ REG_GND REG_GND JACK_AD REG_GND VIDEO_I/O REG_GND REG_GND D3_LNO_PB REG_GND LINE_CNT1 LINE_CNT2 LINE_CNT3 REG_GND REG_GND USB_DET REG_GND TPATPA+ TPB+ TPBREG_GND XVD_SCK VD_SI TP_SEL1 PANEL_VD PANEL_HD BL_CONT D_2.8V BL_-15V A_4.6V KEY_AD5 REG_GND PANEL_B PANEL_G PANEL_R N.C KEY_AD3 KEY_AD6 HI_XRESET REG_GND REG_GND AUDIO_L_I/O AUDIO_R_I/O REG_GND S_C_I/O S_Y_I/O REG_GND D3_LNO_Y REG_GND D3_LNO_PR REG_GND D3_CN REG_GND USB_DUSB_D+ REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND VD_SO XCS_LCD TP_X TP_Y BL_GND BL_GND KEY_AD2 MT_4.9V PANEL_8V EP_2.8V KEY_AD4 REG_GND REG_GND REG_GND 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79

FP-254 FLEXIBLE

32 MIC_GND 34 MIC_GND 36 XCS_AUVOL 38 XVSP_SCK 40 VSP_SO 42 REG_GND 44 REG_GND 46 A_2.8V 48 A_2.8V 50 A_2.8V 52 REG_GND 54 REG_GND 56 AU_4.6V 58 AU_4.6V 60 AU_4.6V 62 REG_GND 64 REG_GND 66 REG_GND 68 HP_R_OUT 70 HP_L_OUT 72 REG_GND 74 HP_JACK_IN 76 SCHARGE_LED 78 N.C. 80 KEY_AD1-2 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15

25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

OO-001 BOARD(1/2) (NOISE CANCELER) (2/2) (MIC AMP)

WW-001 BOARD(MS CONNECTOR)CN302 1012

CN301

14P 14 13 12 11 10 9 8 7 6 5 4 3 2 1 14 13 12 11

CN1011 14P MS_LED_ON D_2.8V REG_GND REG_GND A_4.6V REG_GND MS_VCC_ON MS_BS MS_DIO MS_INSERT MS_SCLK REG_GND REG_GND REG_GND

MS_LED_ON D_2.8V REG_GND REG_GND A_4.6V REG_GND MS_VCC_ON MS_BS MS_DIO MS_INSERT MS_SCLK REG_GND REG_GND REG_GND

12P

FP-255 FLEXIBLE

REG_GND MS_VCC MS_SCLK N.C. MS_INSERT N.C. MS_DIO N.C. MS_BS REG_GND

10 9 8 7 6 5 4 3 2 1

9 8 7

CN1002 12P SHOE_UNREG_GND MIC_FR MIC_FL MIC_GND HOTSHOE_ID1 SHOE_UNREG SHOE_UNREG HOTSHOE_ID2 EXT_STROBE 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3

CN9001

16P

SHOE_UNREG_GND MIC_FR MIC_FL MIC_GND NC NC HOTSHOE_ID1 SHOE_UNREG SHOE_UNREG HOTSHOE_ID2 EXT_STROBE LANC_SIG SHOE_CONT NC NC SHOE_UNREG_GND

FP-253 FLEXIBLE

MEMORY STICK DUO

6 5 411

4 5 6 7 8 9 10 11 12 13

3 2 1

FP-252 FLEXIBLE

LANC_SIG SHOE_CONT SHOE_UNREG_GND 2 4

HOT SHOE

CN1003

XLR BLOCK(PAGE 4-4)

CONTROL KEY BLOCK (SB9000)

CN8702 6P 1 2 3 4 5 6 REG_GND NC KEY_AD2(2nd_S/S)KEY_AD2_5(2ndZOOM_T) KEY_AD2_3(2ndZOOM_W)

CN8701 27P

80P

1 3 5 7 9

LI_3V XBATT_INFO_SW REG_GND SPSP+ REG_GND REG_GND JACK_AD REG_GND VIDEO_I/O REG_GND REG_GND D3_LNO_PB REG_GND LINE_CNT1 LINE_CNT2 LINE_CNT3 REG_GND REG_GND USB_DET REG_GND TPATPA+ TPB+ TPBREG_GND XVD_SCK VD_SI TP_SEL1 PANEL_VD PANEL_HD BL_CONT D_2.8V BL_-15V A_4.6V KEY_AD5 REG_GND PANEL_B PANEL_G PANEL_R

KEY_AD3 KEY_AD6 HI_XRESET REG_GND REG_GND AUDIO_L_I/O AUDIO_R_I/O REG_GND S_C_I/O S_Y_I/O REG_GND D3_LNO_Y REG_GND D3_LNO_PR REG_GND D3_CN REG_GND USB_DUSB_D+ REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND VD_SO XCS_LCD TP_X TP_Y BL_GND BL_GND KEY_AD2 MT_4.9V PANEL_8V EP_2.8V KEY_A

Sony HVR A1service Manual

Documents

time of recording

mini dvcam cassette

digital f

specification mini dv

output impedance

xlr adaptor

rotary heads

stereo ntsc color