Fill in coffee beans (approx. 250 g) Fill tank with fresh water Plug in Place receptacle under nozzle Switch on (on rear of machine) 1. Draw hot water off until steady flow is established 2. Turn tap off 1 2 1 2 3 Note: the ‘insufficient coffee beans’ lamp may flash several times: press product button 3 4 5 Press button to select hot water Press the button once again, to bring back the machine to normal operation STARTING Preparation Ventilate Observe display 1. 2. 3. ADJUST Adjust only when grinding unit is running The machine is preset to a mean value. Recommended settings are 8 (+4 / -2) Select desired grade of powder (fine or rough) during coffee making process! (while grinder is in operation) The result will be visible after 3 to 4 coffee preparations Degree of grinding fast: finer grinding slow: coarser grinding Quantity of coffee 1) Place cup under nozzle 2) Press and hold desired button (espresso or coffee) 3) Release button when correct amount is reached 4) Quantity remains stored in memory Repeat process to change coffee amount flashing: machine is warming up steady: machine ready Funnel for coffee powder Service door / brewing unit Coffee outlet unit (adjustable) Coffee dregs drawer (access: open service door) Drip tray / drip grid Display: drip tray full (Floater appears) Coffee bean container Cappuccino nozzle Mains switch (On / Off) Fresh water tank Operating panel Turning knob steam/hot water Adjusting lever for quantity of coffee Adjusting lever for degree of grinding Refill with beans Refill with water (lamp comes on before tank is completely empty!) Standby Dregs drawer full Request for descaling Clean (see page 6) Hot water Espresso Coffee Powder coffee Ventilate machine / Heating up / PREPARATION 1 Do not use caramelized, flavored or instant coffee! Do not use caramelized, flavoured or instant coffee Built-in rotary plate 1. 2.
6
Embed
Solis-Pal RS en 060603 - Ucoffee-machines.com · for fully automatic espresso machines) - Use fresh roasted coffee beans - Change degree of grinding (select setting - fine or rough)
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Fill in coffee beans(approx. 250 g)
Fill tank with fresh water Plug in
Place receptacleunder nozzle
Switch on(on rear of machine)
1. Draw hot water off untilsteady flow isestablished
2. Turn tap off
1 2
1 2 3 1 2 3 4 5
1 2 3 4 5 6
1 2 3 4 5 6
1 3 4 5 6
To start programming mode, press and hold the two buttonssimultaneously, then switch machine on.
1 2 3
1 2
7
Note: the ‘insufficient coffeebeans’ lamp may flash severaltimes: press product button
3
4 5
Press button to selecthot water
Press the button once again, tobring back the machine tonormal operation
1 3 4 5 62 7
To change programmingrepeat processes
STAR
TIN
GPr
epar
atio
nVe
ntila
te
Observe display
1.
2.
3.
ADJU
ST Adjust only when grinding unit is running
The machine is preset to amean value. Recommendedsettings are 8 (+4/ -2)
Select desired grade of powder(fine or rough) during coffee makingprocess!(while grinder is in operation)
The result will be visibleafter 3 to 4 coffee preparations
Degree of grinding
fast:finer grinding
slow: coarser grinding
Quantity of coffee1) Place cup under nozzle2) Press and hold desired
button (espresso or coffee)3) Release button when
correct amount is reached4) Quantity remains stored in memory
Repeat process to change coffee amount
flashing: machine is warming upsteady: machine ready
Funnel for coffee powder
Service door /brewing unit
Coffee outlet unit(adjustable)
Coffee dregs drawer(access: open service door)
Drip tray /drip grid
Display: drip tray full(Floater appears)
Coffee bean container
Cappuccino nozzle
Mains switch (On /Off)
Fresh water tank
Operating panel
Turning knob steam/hot water
Adjusting lever for quantity of coffee
Adjusting lever for degree of grinding
Refill with beansRefill with water(lamp comes onbefore tank iscompletely empty!)
To improve frothing- Use another coffee mix (insure that it is the appropriate sort of coffee for fully automatic espresso machines)
- Use fresh roasted coffee beans
- Change degree of grinding(select setting - fine or rough)
Do not use caramelized, flavouredor instant coffee
Built-in rotary plate
Coffee flow may be interruptedat anytime by pressing product button
Use heat-resistant glassonly!
Note: when the rinsing function is activated, the ‘clean’ lamp comes on aloneuntil the rinsing process starts; only then will the operational-mode LED come on.
2.
1.
2.
1.
Drain residual wateroff into recipient
2. Close turning knob
HOT
WAT
ER
Adjust nozzle ifnecessary
Place glass under nozzle Start hot waterpreparation
Draw off hot water End preparation andremove glassUse heat-resistant glass
only!
Select hot water Press the button once again,to bring back the machine tonormal operation
1.
2.
Fill in coffee beans(approx. 250 g)
Fill tank with fresh water Plug in
Place receptacleunder nozzle
Switch on(on rear of machine)
1. Draw hot water off untilsteady flow isestablished
2. Turn tap off
1 2
1 2 3 1 2 3 4 5
1 2 3 4 5 6
1 2 3 4 5 6
1 3 4 5 6
To start programming mode, press and hold the two buttonssimultaneously, then switch machine on.
1 2 3
1 2
7
Note: the ‘insufficient coffeebeans’ lamp may flash severaltimes: press product button
3
4 5
Press button to selecthot water
Press the button once again, tobring back the machine tonormal operation
1 3 4 5 62 7
To change programmingrepeat processes
STAR
TIN
GPr
epar
atio
nVe
ntila
te
Observe display
1.
2.
3.
ADJU
ST Adjust only when grinding unit is running
The machine is preset to amean value. Recommendedsettings are 8 (+4/ -2)
Select desired grade of powder(fine or rough) during coffee makingprocess!(while grinder is in operation)
The result will be visibleafter 3 to 4 coffee preparations
Degree of grinding
fast:finer grinding
slow: coarser grinding
Quantity of coffee1) Place cup under nozzle2) Press and hold desired
button (espresso or coffee)3) Release button when
correct amount is reached4) Quantity remains stored in memory
Repeat process to change coffee amount
flashing: machine is warming upsteady: machine ready
Funnel for coffee powder
Service door /brewing unit
Coffee outlet unit(adjustable)
Coffee dregs drawer(access: open service door)
Drip tray /drip grid
Display: drip tray full(Floater appears)
Coffee bean container
Cappuccino nozzle
Mains switch (On /Off)
Fresh water tank
Operating panel
Turning knob steam/hot water
Adjusting lever for quantity of coffee
Adjusting lever for degree of grinding
Refill with beansRefill with water(lamp comes onbefore tank iscompletely empty!)
To improve frothing- Use another coffee mix (insure that it is the appropriate sort of coffee for fully automatic espresso machines)
- Use fresh roasted coffee beans
- Change degree of grinding(select setting - fine or rough)
Do not use caramelized, flavouredor instant coffee
Built-in rotary plate
Coffee flow may be interruptedat anytime by pressing product button
Use heat-resistant glassonly!
Note: when the rinsing function is activated, the ‘clean’ lamp comes on aloneuntil the rinsing process starts; only then will the operational-mode LED come on.
2.
1.
2.
1.
Drain residual wateroff into recipient
2. Close turning knob
HOT
WAT
ER
Adjust nozzle ifnecessary
Place glass under nozzle Start hot waterpreparation
Draw off hot water End preparation andremove glassUse heat-resistant glass
only!
Select hot water Press the button once again,to bring back the machine tonormal operation
1.
2.
Fill in coffee beans(approx. 250 g)
Fill tank with fresh water Plug in
Place receptacleunder nozzle
Switch on(on rear of machine)
1. Draw hot water off untilsteady flow isestablished
2. Turn tap off
1 2
1 2 3 1 2 3 4 5
1 2 3 4 5 6
1 2 3 4 5 6
1 3 4 5 6
To start programming mode, press and hold the two buttonssimultaneously, then switch machine on.
1 2 3
1 2
7
Note: the ‘insufficient coffeebeans’ lamp may flash severaltimes: press product button
3
4 5
Press button to selecthot water
Press the button once again, tobring back the machine tonormal operation
1 3 4 5 62 7
To change programmingrepeat processes
STAR
TIN
GPr
epar
atio
nVe
ntila
te
Observe display
1.
2.
3.
ADJU
ST Adjust only when grinding unit is running
The machine is preset to amean value. Recommendedsettings are 8 (+4/ -2)
Select desired grade of powder(fine or rough) during coffee makingprocess!(while grinder is in operation)
The result will be visibleafter 3 to 4 coffee preparations
Degree of grinding
fast:finer grinding
slow: coarser grinding
Quantity of coffee1) Place cup under nozzle2) Press and hold desired
button (espresso or coffee)3) Release button when
correct amount is reached4) Quantity remains stored in memory
Repeat process to change coffee amount
flashing: machine is warming upsteady: machine ready
Funnel for coffee powder
Service door /brewing unit
Coffee outlet unit(adjustable)
Coffee dregs drawer(access: open service door)
Drip tray /drip grid
Display: drip tray full(Floater appears)
Coffee bean container
Cappuccino nozzle
Mains switch (On /Off)
Fresh water tank
Operating panel
Turning knob steam/hot water
Adjusting lever for quantity of coffee
Adjusting lever for degree of grinding
Refill with beansRefill with water(lamp comes onbefore tank iscompletely empty!)
To improve frothing- Use another coffee mix (insure that it is the appropriate sort of coffee for fully automatic espresso machines)
- Use fresh roasted coffee beans
- Change degree of grinding(select setting - fine or rough)
Do not use caramelized, flavouredor instant coffee
Built-in rotary plate
Coffee flow may be interruptedat anytime by pressing product button
Use heat-resistant glassonly!
Note: when the rinsing function is activated, the ‘clean’ lamp comes on aloneuntil the rinsing process starts; only then will the operational-mode LED come on.
2.
1.
2.
1.
Drain residual wateroff into recipient
2. Close turning knob
HOT
WAT
ER
Adjust nozzle ifnecessary
Place glass under nozzle Start hot waterpreparation
Draw off hot water End preparation andremove glassUse heat-resistant glass
only!
Select hot water Press the button once again,to bring back the machine tonormal operation
1.
2.
Fill water tank,place receptacle underoutlet
Throw in cleaningtablet
Press Clean for 5 sec.1 2 3
1 2 3
Loosen the knurlingscrew, remove nozzle
Clean with dampcloth
Disassemble nozzle. Placenozzle parts under runningwater and remove milk residue.Dry separate parts, reassemble,and mount on machine.
Every 3-4 months or
if lamp
When button «Clean» goes out:Cleaning is finished
1
2
- To descale, make sure that the mains cable is plugged in and the machine switched on. During this process the heating is deactivated.
- Use a non-poisonous, harmless, commercial decalcifying agent.
- NEVER use VINEGAR (possible damage to device!)- Note manufacturer’s instructions!- If the machine is turned off during the descaling procedure, it will continue again where it left off when the machine is turned on again.
1
2
(automatic)DESCALE
1. Place large receptacle under Cappuccino nozzle2. Solipol rated 1:1 (0,5 l Solipol /0,5 l Wasser)
in the water tank.
Preparation
Descale
Press buttons: Buttons «Clean»,«Powder» and LED «Descale»light
Open turning knob:LED «Descale» flashes /«Clean», «Powder» light
As soon as buttons / LED flash:close turning knob
1 2 3
3 Rinse 1. Rinse water tank and fill2. Open turning knob and draw off tank contents3. Close turning knob, descaling is complete
9876
- Nominal voltage see type plate on the machine- Nominal output see type plate on the machine- Power see type plate on the machine- Frame metal-plastic- Dimensions (L x W x D) approx. 27,5 x 35 x 42 cm/approx. 11 x 14,4 x 16,9 Inch- Weight net approx. 11 kg /net 24.25 lb- Length of mains cable 1.2 m- Place for extra cable yes- Control panel on the front- Water tank removable- Capacity wate tank approx. 2 l
for heating and safety thermostat- Steam outlet continuously adjustable
- Switch on main switch- Check plug and power connection
- Fill up a measure of powder coffee
No power to the machine
No indication
Only water instead of coffee comeswhen «Powder coffee» is selected
TROUBLESHOOTING
- Pre-heat cups- Possibly clean brewing unit, descale if necessary
- Clean nozzle with needle(when the machine is switchedoff and tap is closed)Hot water / steam nozzle blocked
Coffee is not hot enough
No hot water/steam
- Descale machine
Heating time too long,not enough water
Brewing unit cannotbe removed
1. Close service door2. Switch on machine3. Brewing unit is unlocked4. Where appropriate, continue maintenance
of brewing unit, see page 9
Brewing unit cannotbe inserted
Restore brewing unit tooriginal position
1 2
Preparation does not startDisplay:
= Dregs drawer missing= Dregs drawer full
(after 14 coffees)
= Request for cleaningafter 250 coffees
= Temperature too high
= Request for descaling
= Brewing unit blocked= Brewing unit missing
= Door open
Wipe with a soft, damp cloth
Rinse under running water
Casing
Container for coffee grounds anddrip tray
CLEANING
Rinse under running water
Remove the filter that is in the water tank andrinse thoroughly. Replace by turning and pressinglightly into place.
Clean weekly
Water tank
Coffee outlet
Use a mild non abrasive cleaning agent!
- The machine must not be connected to main switch for cleaning.- Do not use conventional and /or microwave ovens for drying the coffee machine components.
2. Press button «Coffee powder»(do not fill in coffee powder)
Brewing unit
Clean weekly.Never clean the brewing unitin the dishwasher!
1. Open service door.Remove drip tray /grounds container
2.1 Loosen sieve with key...
2.2 ...and remove
2. Press PUSH-position and removebrewing unit. If necessary, unscrew theuppermost sieve in the brewing unit
Clean everything under running warm waterand let it dry. Clean service area
3. Reassemble brewing unit andslide in, do NOT press the PUSH-position!
4. Insert drip tray and grounds container,then close service door
1. Place receptacle under coffee outlet
3. Let flow pure water through the systemto avoid residuals in the pipes etc.
The documentation for your new coffee machine consists of these instructions and theseparately enclosed safety advice. This documentation should be read before the installationof the device. Keep the documentation handy at any time and pass it on to any otheruser.
Duration: approx. 45 min.
= Ventilate machine= Fresh water tank empty
= The motor of the grinding unitis blocked
= No beans
Operating Instruction
Duration: approx. 6 min.
See page 1, ventilate
See page 6, descaleNote: coffee can still be prepared
See page 6, cleanNote: coffee can still be prepared
See page 1, Ventilate
See page 8, Troubleshooting (Brewing unit)Insert brewing unit
Close door
Tagliare
Machine
CLEAN
Cappuccino nozzle
Supplied accessories
Key for strainerdismantling /assembly
Cleaning brush
Technical data
Coffee measure Test strip for water hardness
Cleaning agent
Cleaning tablets Descaling agent(optional)
TSM SUCCESS MANUAL® Safe to use - easy to understand due toTSM® - Total Security Management and ergonomic communication®
This TSM SUCCESS MANUAL® has been examined by SEV for conformity with the safety-relevant standards, and hasbeen analysed by an application-oriented risk analysis for the completeness and correctness of the indications for a safeuse of the appl iance. Thereby we assume a use with which can be reckoned based on common-sense.
R A P I D S T E A M
Fill water tank,place receptacle underoutlet
Throw in cleaningtablet
Press Clean for 5 sec.1 2 3
1 2 3
Loosen the knurlingscrew, remove nozzle
Clean with dampcloth
Disassemble nozzle. Placenozzle parts under runningwater and remove milk residue.Dry separate parts, reassemble,and mount on machine.
Every 3-4 months or
if lamp
When button «Clean» goes out:Cleaning is finished
1
2
- To descale, make sure that the mains cable is plugged in and the machine switched on. During this process the heating is deactivated.
- Use a non-poisonous, harmless, commercial decalcifying agent.
- NEVER use VINEGAR (possible damage to device!)- Note manufacturer’s instructions!- If the machine is turned off during the descaling procedure, it will continue again where it left off when the machine is turned on again.
1
2
(automatic)DESCALE
1. Place large receptacle under Cappuccino nozzle2. Solipol rated 1:1 (0,5 l Solipol /0,5 l Wasser)
in the water tank.
Preparation
Descale
Press buttons: Buttons «Clean»,«Powder» and LED «Descale»light
Open turning knob:LED «Descale» flashes /«Clean», «Powder» light
As soon as buttons / LED flash:close turning knob
1 2 3
3 Rinse 1. Rinse water tank and fill2. Open turning knob and draw off tank contents3. Close turning knob, descaling is complete
9876
- Nominal voltage see type plate on the machine- Nominal output see type plate on the machine- Power see type plate on the machine- Frame metal-plastic- Dimensions (L x W x D) approx. 27,5 x 35 x 42 cm/approx. 11 x 14,4 x 16,9 Inch- Weight net approx. 11 kg /net 24.25 lb- Length of mains cable 1.2 m- Place for extra cable yes- Control panel on the front- Water tank removable- Capacity wate tank approx. 2 l
for heating and safety thermostat- Steam outlet continuously adjustable
- Switch on main switch- Check plug and power connection
- Fill up a measure of powder coffee
No power to the machine
No indication
Only water instead of coffee comeswhen «Powder coffee» is selected
TROUBLESHOOTING
- Pre-heat cups- Possibly clean brewing unit, descale if necessary
- Clean nozzle with needle(when the machine is switchedoff and tap is closed)Hot water / steam nozzle blocked
Coffee is not hot enough
No hot water/steam
- Descale machine
Heating time too long,not enough water
Brewing unit cannotbe removed
1. Close service door2. Switch on machine3. Brewing unit is unlocked4. Where appropriate, continue maintenance
of brewing unit, see page 9
Brewing unit cannotbe inserted
Restore brewing unit tooriginal position
1 2
Preparation does not startDisplay:
= Dregs drawer missing= Dregs drawer full
(after 14 coffees)
= Request for cleaningafter 250 coffees
= Temperature too high
= Request for descaling
= Brewing unit blocked= Brewing unit missing
= Door open
Wipe with a soft, damp cloth
Rinse under running water
Casing
Container for coffee grounds anddrip tray
CLEANING
Rinse under running water
Remove the filter that is in the water tank andrinse thoroughly. Replace by turning and pressinglightly into place.
Clean weekly
Water tank
Coffee outlet
Use a mild non abrasive cleaning agent!
- The machine must not be connected to main switch for cleaning.- Do not use conventional and /or microwave ovens for drying the coffee machine components.
2. Press button «Coffee powder»(do not fill in coffee powder)
Brewing unit
Clean weekly.Never clean the brewing unitin the dishwasher!
1. Open service door.Remove drip tray /grounds container
2.1 Loosen sieve with key...
2.2 ...and remove
2. Press PUSH-position and removebrewing unit. If necessary, unscrew theuppermost sieve in the brewing unit
Clean everything under running warm waterand let it dry. Clean service area
3. Reassemble brewing unit andslide in, do NOT press the PUSH-position!
4. Insert drip tray and grounds container,then close service door
1. Place receptacle under coffee outlet
3. Let flow pure water through the systemto avoid residuals in the pipes etc.
The documentation for your new coffee machine consists of these instructions and theseparately enclosed safety advice. This documentation should be read before the installationof the device. Keep the documentation handy at any time and pass it on to any otheruser.
Duration: approx. 45 min.
= Ventilate machine= Fresh water tank empty
= The motor of the grinding unitis blocked
= No beans
Operating Instruction
Duration: approx. 6 min.
See page 1, ventilate
See page 6, descaleNote: coffee can still be prepared
See page 6, cleanNote: coffee can still be prepared
See page 1, Ventilate
See page 8, Troubleshooting (Brewing unit)Insert brewing unit
Close door
Tagliare
Machine
CLEAN
Cappuccino nozzle
Supplied accessories
Key for strainerdismantling /assembly
Cleaning brush
Technical data
Coffee measure Test strip for water hardness
Cleaning agent
Cleaning tablets Descaling agent(optional)
TSM SUCCESS MANUAL® Safe to use - easy to understand due toTSM® - Total Security Management and ergonomic communication®
This TSM SUCCESS MANUAL® has been examined by SEV for conformity with the safety-relevant standards, and hasbeen analysed by an application-oriented risk analysis for the completeness and correctness of the indications for a safeuse of the appl iance. Thereby we assume a use with which can be reckoned based on common-sense.
R A P I D S T E A M
Fill water tank,place receptacle underoutlet
Throw in cleaningtablet
Press Clean for 5 sec.1 2 3
1 2 3
Loosen the knurlingscrew, remove nozzle
Clean with dampcloth
Disassemble nozzle. Placenozzle parts under runningwater and remove milk residue.Dry separate parts, reassemble,and mount on machine.
Every 3-4 months or
if lamp
When button «Clean» goes out:Cleaning is finished
1
2
- To descale, make sure that the mains cable is plugged in and the machine switched on. During this process the heating is deactivated.
- Use a non-poisonous, harmless, commercial decalcifying agent.
- NEVER use VINEGAR (possible damage to device!)- Note manufacturer’s instructions!- If the machine is turned off during the descaling procedure, it will continue again where it left off when the machine is turned on again.
1
2
(automatic)DESCALE
1. Place large receptacle under Cappuccino nozzle2. Solipol rated 1:1 (0,5 l Solipol /0,5 l Wasser)
in the water tank.
Preparation
Descale
Press buttons: Buttons «Clean»,«Powder» and LED «Descale»light
Open turning knob:LED «Descale» flashes /«Clean», «Powder» light
As soon as buttons / LED flash:close turning knob
1 2 3
3 Rinse 1. Rinse water tank and fill2. Open turning knob and draw off tank contents3. Close turning knob, descaling is complete
9876
- Nominal voltage see type plate on the machine- Nominal output see type plate on the machine- Power see type plate on the machine- Frame metal-plastic- Dimensions (L x W x D) approx. 27,5 x 35 x 42 cm/approx. 11 x 14,4 x 16,9 Inch- Weight net approx. 11 kg /net 24.25 lb- Length of mains cable 1.2 m- Place for extra cable yes- Control panel on the front- Water tank removable- Capacity wate tank approx. 2 l
for heating and safety thermostat- Steam outlet continuously adjustable
- Switch on main switch- Check plug and power connection
- Fill up a measure of powder coffee
No power to the machine
No indication
Only water instead of coffee comeswhen «Powder coffee» is selected
TROUBLESHOOTING
- Pre-heat cups- Possibly clean brewing unit, descale if necessary
- Clean nozzle with needle(when the machine is switchedoff and tap is closed)Hot water / steam nozzle blocked
Coffee is not hot enough
No hot water/steam
- Descale machine
Heating time too long,not enough water
Brewing unit cannotbe removed
1. Close service door2. Switch on machine3. Brewing unit is unlocked4. Where appropriate, continue maintenance
of brewing unit, see page 9
Brewing unit cannotbe inserted
Restore brewing unit tooriginal position
1 2
Preparation does not startDisplay:
= Dregs drawer missing= Dregs drawer full
(after 14 coffees)
= Request for cleaningafter 250 coffees
= Temperature too high
= Request for descaling
= Brewing unit blocked= Brewing unit missing
= Door open
Wipe with a soft, damp cloth
Rinse under running water
Casing
Container for coffee grounds anddrip tray
CLEANING
Rinse under running water
Remove the filter that is in the water tank andrinse thoroughly. Replace by turning and pressinglightly into place.
Clean weekly
Water tank
Coffee outlet
Use a mild non abrasive cleaning agent!
- The machine must not be connected to main switch for cleaning.- Do not use conventional and /or microwave ovens for drying the coffee machine components.
2. Press button «Coffee powder»(do not fill in coffee powder)
Brewing unit
Clean weekly.Never clean the brewing unitin the dishwasher!
1. Open service door.Remove drip tray /grounds container
2.1 Loosen sieve with key...
2.2 ...and remove
2. Press PUSH-position and removebrewing unit. If necessary, unscrew theuppermost sieve in the brewing unit
Clean everything under running warm waterand let it dry. Clean service area
3. Reassemble brewing unit andslide in, do NOT press the PUSH-position!
4. Insert drip tray and grounds container,then close service door
1. Place receptacle under coffee outlet
3. Let flow pure water through the systemto avoid residuals in the pipes etc.
The documentation for your new coffee machine consists of these instructions and theseparately enclosed safety advice. This documentation should be read before the installationof the device. Keep the documentation handy at any time and pass it on to any otheruser.
Duration: approx. 45 min.
= Ventilate machine= Fresh water tank empty
= The motor of the grinding unitis blocked
= No beans
Operating Instruction
Duration: approx. 6 min.
See page 1, ventilate
See page 6, descaleNote: coffee can still be prepared
See page 6, cleanNote: coffee can still be prepared
See page 1, Ventilate
See page 8, Troubleshooting (Brewing unit)Insert brewing unit
Close door
Tagliare
Machine
CLEAN
Cappuccino nozzle
Supplied accessories
Key for strainerdismantling /assembly
Cleaning brush
Technical data
Coffee measure Test strip for water hardness
Cleaning agent
Cleaning tablets Descaling agent(optional)
TSM SUCCESS MANUAL® Safe to use - easy to understand due toTSM® - Total Security Management and ergonomic communication®
This TSM SUCCESS MANUAL® has been examined by SEV for conformity with the safety-relevant standards, and hasbeen analysed by an application-oriented risk analysis for the completeness and correctness of the indications for a safeuse of the appl iance. Thereby we assume a use with which can be reckoned based on common-sense.