Soft Serve/Shake Combination Freezer Taylor Model C602 Place this chapter in the Shakes/Desserts section of the Equipment Manual. Manufactured exclusively for McDonald's® by Taylor Company 750 N. Blackhawk Blvd. Rockton, IL 61072 Phone: (815) 624-8333 Toll Free Number Outside Illinois: 1 (800) 228-8309 Inside Illinois: 1 (800) 851-5639 Fax: (815) 624-8000 Table of Contents Introduction Page 1 ..................................................... Safety Page 1 .......................................................... Parts Identification/Function Page 4 ....................................... Important to the Operator Page 30 ......................................... Daily Opening Procedures Page 33 ......................................... Syrup System Page 38 .................................................... Daily Closing Procedures Page 41 ......................................... Scheduled Maintenance - Syrup System Page 46 ............................ Syrup Topping Pump Page 49 ............................................. Manual Brush Cleaning Page 54 ........................................... Equipment Set-Up Page 59 ................................................ VFD Screens Page 74 .................................................... Manager's Menu Page 78 ................................................. Troubleshooting Guide Page 93 ............................................ Parts Replacement Schedule Page 107 ...................................... Ordering/Service Information Page 109 ...................................... Wiring Diagrams Page 110 ................................................. Warranty A warranty checkout card is shipped with every new freezer that leaves the factory. The warranty checkout card is packed in an envelope which also contains this operator's manual. Refer to the warranty checkout card and the warranty classifications listed in the Parts Identification/Function section when service is performed on your freezer. It is recommended that the operator take the necessary time to carefully read through the complete warranty information contained in the warranty checkout card. Any questions or unclear statements found within the card should be made clear to you upon delivery of the freezer. Thoroughly understand your warranty protection before you begin operation. For any questions pertaining to the Taylor Warranty, please contact your authorized Taylor Distributor or Taylor Company, Rockton, Illinois 61072. This manual is for the exclusive use of licensees and employees of McDonald's Corporation. E2005 McDonald's Corporation All Rights Reserved May, 2005 (Original Publication) (Updated September, 2013) EM SD11 Printed in The United States of America
116
Embed
Soft Serve/Shake Combination Freezer Taylor Model … · Soft Serve/Shake Combination Freezer Taylor Model C602 ... Manager's Menu Page 78 ... Communication Standard (HCS) manual
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Soft Serve/Shake Combination FreezerTaylor Model C602Place this chapter in theShakes/Desserts section of theEquipment Manual.
Manufactured exclusively forMcDonald's® by
Taylor Company750 N. Blackhawk Blvd.Rockton, IL 61072Phone: (815) 624-8333Toll Free NumberOutside Illinois:1 (800) 228-8309Inside Illinois:1 (800) 851-5639Fax: (815) 624-8000
WarrantyA warranty checkout card is shipped with every new freezer that leaves the factory. The warranty checkout card ispacked in an envelope which also contains this operator's manual. Refer to the warranty checkout card and the warrantyclassifications listed in the Parts Identification/Function section when service is performed on your freezer.It is recommended that the operator take the necessary time to carefully read through the complete warranty informationcontained in the warranty checkout card. Any questions or unclear statements found within the card should be madeclear to you upon delivery of the freezer. Thoroughly understand your warranty protection before you begin operation.For any questions pertaining to the Taylor Warranty, please contact your authorized Taylor Distributor or TaylorCompany, Rockton, Illinois 61072.
This manual is for the exclusive use of licensees and employees of McDonald's Corporation.E2005 McDonald's CorporationAll Rights Reserved
May, 2005 (Original Publication)(Updated September, 2013)
EM SD11
Printed inThe United States of America
1 130415
INTRODUCTION
The Model C602 is a combination shake andsoft serve freezer. The soft serve side uses a3.4 quart (3.2 liter) freezing cylinder with asingle spout door.
The shake side has a 7 quart (6.6 liter)freezing cylinder with a four flavor dispensingdoor. The touch panel has four flavor symbolsfor selecting and drawing the desired shakeflavor. When dispensing a shake, the cup isplaced on the shake cup holder located belowthe door spout. A shake flavor symbol isselected to automatically raise the draw valve,allowing frozen mix and syrup to enter thedoor where they are blended and dispensedas a finished shake.
A portion control device will sense the filling ofthe shake cup and automatically close thedraw valve upon filling the shake cup to thecorrect level. The operator also has the abilityto override the portion control and stopdispensing the shake by touching any of thefour shake flavor symbols. The shake drawvalve can also be raised and lowered in theWASH and OFF modes by selecting any ofthe four flavor symbols to enable cleaning,sanitizing, and priming.
Shake syrup is stored in the lower frontcompartment. Each syrup flavor is delivered tothe dispensing door by a peristaltic pump.Syrup can be pumped directly from disposableplastic jugs, stainless steel tanks, or adaptedto syrup-in-bag dispensing. The proper syrupdelivery rate is achieved by calibrating eachsyrup flavor.
The mix is located in the mix hopper and ispumped to the freezing cylinder by an air/mixpump.
When your machine is delivered or if it hasbeen in the OFF position for more than 24hours, disassemble the freezer following theManual Brush Cleaning procedures found onpage 54. Follow the Equipment Set-Upprocedures on page 59 to re-assemble yourmachine.
The machine must be disassembled, cleaned,sanitized and lubricated at least once everytwo weeks. Syrup lines must be cleaned andsanitized weekly.It is recommended that these operatingprocedures be followed closely to insurecorrect assembly and disassembly of thefreezer.The C602 is designed for indoor use only.
Note: Only instructions originating from thefactory or its authorized translationrepresentative(s) are considered to be theoriginal set of instructions.
SAFETY
Always follow these safety precautions whenoperating the freezer:
DO NOT operate the freezer withoutreading this operator's manual. Failure tofollow this instruction may result in equipmentdamage, poor freezer performance, healthhazards, or personal injury.
This appliance is to be used only bytrained personnel. It is not intended for use bychildren or people with reduced physical,sensory, or mental capabilities, or lack ofexperience and knowledge, unless givensupervision or instruction concerning the useof the appliance by a person responsible fortheir safety. Children should be supervised toensure that they do not play with theappliance.
S DO NOT operate the freezer unless itis properly grounded.
S DO NOT operate freezer with largerfuses than specified on data label.
S All repairs must be performed by anauthorized Taylor service agent.
S The main power supplies to the freezermust be disconnected prior toperforming any repairs.
S Cord Connected Units: Only Taylorauthorized service technicians orlicensed electricians may install a plugor replacement cord on this unit.
2 130415
S Stationary appliances which are notequipped with a power cord and a plugor other device to disconnect theappliance from the power source musthave an all-pole disconnecting devicewith a contact gap of at least 3 mminstalled in the external installation.
S Appliances that are permanentlyconnected to fixed wiring and for whichleakage currents may exceed 10 mA,particularly when disconnected or notused for long periods, or during initialinstallation, shall have protectivedevices such as a GFI, to protectagainst the leakage of current, installedby the authorized personnel to thelocal codes.
S Supply cords used with this unit shallbe oil-resistant, sheathed flexible cablenot lighter than ordinarypolychloroprene or other equivalentsynthetic elastomer-sheathed cord(Code designation 60245 IEC 57)installed with the proper cordanchorage to relieve conductors fromstrain, including twisting, at theterminals and protect the insulation ofthe conductors from abrasion.
If the supply cord is damaged, it mustbe replaced by the manufacturer, itsservice agent, or similarly qualifiedperson, in order to avoid a hazard.
Failure to follow these instructions may resultin personal injury, equipment damage, or poorfreezer performance.
This equipment is provided with agrounding lug that is to be properly attached tothe rear of the frame by the authorizedinstaller. The installation location is marked bythe equipotential bonding symbol (5021 of IEC60417-1) on the removable panel and theframe.
S DO NOT operate the freezer unless allservice panels and access doors arerestrained with screws.
S DO NOT remove the door, beater,scraper blades, drive shaft or air/mixpump unless all control switches are inthe OFF position.
Failure to follow these instructions may resultin severe personal injury from hazardousmoving parts.
DO NOT attempt to draw product ordisassemble the unit during the HEAT cycle.The product is hot and under extremepressure.
S DO NOT put objects or fingers in thedoor spout. Failure to follow thisinstruction may result in contaminatedproduct or personal injury from bladecontact.
S USE EXTREME CAUTION whenremoving the beater assembly. Thescraper blades are very sharp and maycause injury.
S CAUTION-SHARP EDGES: Twopeople are required to handle thecup/cone dispenser. Protective glovesmust be worn and the mounting holesmust NOT be used to lift or hold thedispenser. Failure to follow thisinstruction can result in personal injuryto fingers or equipment damage.
Access to the service area of the unitis restricted to persons having knowledge andpractical experience with the appliance, inparticular as far as safety and hygiene areconcerned.
3 130415
This freezer must be placed on a levelsurface. Failure to comply may result inpersonal injury or equipment damage.
Cleaning and sanitizing schedules aregoverned by your Federal, State, or localregulatory agencies and must be followedaccordingly. Please refer to the cleaningsection of this manual for the properprocedure to clean this unit.
This machine is designed to maintainproduct temperature under 41°F (5°C). Anyproduct being added to this machine must bebelow 41°F (5°C). Failure to follow thisinstruction may result in health hazards andpoor freezer performance.
DO NOT install the unit in an areawhere a water jet could be used, and do notuse a water jet to clean or rinse the freezer.Failure to follow these instructions may resultin serious electrical shock.
This freezer is designed to operate indoors,under normal ambient temperatures of70° - 75°F (21° - 24°C). The freezer hassuccessfully performed in high ambienttemperatures of 104°F (40°C) at reducedcapacities.
DO NOT obstruct air intake and dischargeopenings: 3” (76 mm) minimum air space allsides. Install the deflector provided to preventrecirculation of warm air. Failure to follow thisinstruction may cause poor freezerperformance and damage to the machine.
DO NOT run the machine without product.Failure to follow this instruction can result indamage to the machine.
NOTICE all warning labels that have beenattached to the freezer to further point outsafety precautions to the operator.
HAZARD COMMUNICATION STANDARD(HCS) - The procedure(s) in this manualinclude the use of chemical products.These chemical products will behighlighted with bold faced letters followedby the abbreviation (HCS) in the textportion of the procedure. See the HazardCommunication Standard (HCS) manual forthe appropriate Material Safety DataSheet(s) (MSDS).
This piece of equipment is made in Americaand has American sizes of hardware. Allmetric conversions are approximate and varyin size.
NOISE LEVEL: Airborne noise emission doesnot exceed 78 dB(A) when measured at adistance of 1.0 meter from the surface of themachine and at a height of 1.6 meters fromthe floor.
If the crossed out wheeled bin symbolis affixed to this product, it signifies that thisproduct is compliant with the EU Directive aswell as other similar legislation in effect afterAugust 13, 2005. Therefore, it must becollected separately after its use is completed,and cannot be disposed as unsorted municipalwaste.
The user is responsible for returning theproduct to the appropriate collection facility, asspecified by your local code.
For additional information regarding applicablelocal laws, please contact the municipal facilityand/or local distributor.
4 111205
PARTS IDENTIFICATION/FUNCTIONS
Exploded View (See Figure 1)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 053809-1 Cover-Hopper*Black* 2 Protects mix in mix hopper fromany debris. Helps keeptemperature in mix hopperuniform.
103
2 X44797 Agitator Assembly 2 Stirs product in mix hopper toassure even temperature.
103
3 043934 Pin-Retaining HopperCover
2 Holds hopper cover while fillinghopper with mix.
103
4 X56003 Pan-Drip-Rear 8-3/4”Long (22.2 cm)
2 Used to catch any mix leakagefrom the mix pump.
103
5 066724 Panel-Rear-Upper 1 Provides access to internalcomponents.
103
6 X48228 Guide A.-Drip Pan MixPump
2 Holds the mix pump drip pan inplace.
103
7 055959 Panel-Rear-Lower 1 Provides access to internalcomponents.
103
8 X56005 Pan-Drip-Side 12-3/4”Long (32.4 cm)
2 Used to catch any mix leakagefrom the rear shell bearing.
103
9
056692 Trim-Corner-Rear RightSide
1 Cosmetic trim. Seals the panelstogether.
103
056693 Trim-Corner-Rear LeftSide
1 Cosmetic trim. Seals the panelstogether.
103
10 044106 Caster-4” 2 Wheels which support the unit andallow easier movement.
103
11 011694 Screw-1/4 - 20 x 3/8 4 Attaches the panels to the frame. 00012 055950 Panel-Side Right 1 Panel which provides access to
21 055957 Panel-Side Left 1 Panel which provides access tointernal components.
103
22 052779-3 Filter-Air 18.0 L x13.5 H x .70 W
2 Filters dust and dirt from the maincondenser.
000
23 046437 Caster-4” Swv 3/4-10Stem w/Brake
2 Wheels which support the unit andallow easier movement, with locksto stop movement.
103
Figure 1
6 120208
Front View (See Figure 2)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 055987 Stud-Nose Cone 8 Freezer door sits on these studs.Handscrews hold door in place.
103
2 056674 Fitting-Panel Mount QD 4 Quick disconnect fitting for doorsyrup line.
103
3 068394 Clip-Spring Cup Holder 2 Holds the cup in place duringdispensing.
103
4
X59304 Line A.-Syrup Door 4 Delivers syrup to the freezer door.Has a small slot for thin syrup. 103
X56652 Line A.-Syrup Door4
Delivers syrup to the freezer door.Has a large slot for thick syrupand particulates.
103
5 064942 Shield-PyroelectricSensor
1 Plastic cover that protects thepyroelectric sensor.
000
†6 016121 Magnet-Catch Assy. 2 Holds the cabinet door closed. 1037 X53353-BLU
X53353-BRNX53353-REDX53353-WHT
Fitting A.-Syrup Jug 1 pertank
Transfers syrup from the syrup jugor tank to the peristaltic pump.
103
**7 X58450 Line A.-Syrup 4 Transfers syrup from the syrupbag to the peristaltic pump.
103
7a053040-BLU053040-BRN053040-RED053040-WHT
Cap-Ultimate Syrup 1 ea. Attachment covers for containers. 000
7b 053052-36 Hose-Beverage 4 Delivers syrup to peristaltic pump. 0007c X53175 Tube A.-Syrup Pick Up 4 Transfers syrup from container to
pump.000
K7d 053036 Ferrule-.625 ID 4 Clamps syrup hose on fitting. 000
8X58607-L Door A.-Cabinet 2 Insulates left side syrup cabinet. 103X58607-R Door A.-Cabinet 2 Insulates right side syrup cabinet. 103
9 059144 Basket-Door-Wire 2 Rack for storage. 10310 051574 Screw-Adjustment 1 Adjusts the sensing eye to
determine correct level of shake.103
11 056008 Holder-Cup Shake 1 Holds cup during dispensing. 103*12 X53800-BRN Pump A.-Syrup-
Heated (Chocolate)1 Dispenses heated sundae
topping.103
*13 X53800-TAN Pump A.-Syrup-Heated (Caramel)
1 Dispenses heated sundaetopping.
103
14 036435 Gasket-Drip Lip 2 Helps prevent liquid from drippingdown front of machine.
000
K 015971 Pin-Roll - .094 x .562 1 Secures spinner shaft in couplingassembly.
000
K Not Shown* For machines manufactured prior to serial number M1080000.** Bag Syrup System (Not Shown)† Prior to serial number K4091994, use 058630 Latch-Door-Magnetic.
7 120208
Front View
Figure 2
8 120208
Syrup Cabinet View (See Figure 3)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 056016 Shelf-Syrup 1 Provides access to syrup pumps. 1032 052916 Pump-Peristaltic 4 Pumps syrup to freezer door. 1033 058725 Motor-Gear 161 RPM 4 Drives peristaltic pump rollers. 1034 059144 Basket-Door-Wire 2 Rack for storage. 1035 058613 Block-Hinge 4 Attaches door to syrup cabinet. 1036 058614 Block-Hinge 4 Attaches door to syrup cabinet. 103
*7 016121 Magnet-Catch Assy. 2 Holds the cabinet door closed. 1038 002201 Screw-6-32 x 3/8 4 Secures magnet to latch bracket. 1039 043075 Washer #4 4 Secures latch bracket to machine. 103
10 058317 Screw 4-40 x 3/8 4 Secures latch bracket to machine. 10311 065933 Handle-Door Short 2 Handle used for opening syrup
cabinet door.103
12 X58607-L Door A.-Cabinet (Left) 1 Insulates left side syrup cabinet. 10313 X58607-R Door A.-Cabinet (Right) 1 Insulates right side syrup cabinet. 103
*Prior to serial number K4091994, use 058630 Latch-Door-Magnetic.
Figure 3
9
Mix Pump & Tubes (See Figure 4)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
5 056873-XX Cap-Valve 1 Provides a metered passage forair and mix. The suffix numberindicates the air orifice size.
103
6 053527 Gasket-SimplifiedPump
1 Controls the flow of air and mixthrough the pump (do notlubricate).
000
7 054944 Adaptor-Mix InletShake-Blue
1 Provides passageway for air/mixintake and discharge.
103
8 016132 O-Ring-11/16 OD - Red 2 Provides a seal at each end of themix feed tube.
000
9 044731 Pin-Cotter 1 Secures mix inlet tube to pumpadaptor.
103
10 X41947 Shaft A.-Drive MixPump
1 Rotates counter-clockwise tomove piston back and forth.
103
10a 039235 Crank-Drive 1 Delivers motion to piston. 10310b 041948 Shaft-Drive 1 Delivers motion from pump motor
to crank.103
10c 048632 O-Ring-Drive Shaft 2 Provides seal to prevent mix fromleaking into rear drip pans.
000
10d 008904 O-Ring 1-3/4 1 Provides seal between crank andpump sleeve.
000
11 044641 Clip-Mix PumpRetainer
1 Secures air/mix pump to drive hubin mix reservoir.
103
12 X55973 Tube A.-Feed- HopperShake
1 Mix and air is pumped through thistube from the pump to thefreezing cylinder.
103
13 056524 Ring-Check .120 OD 1 Releases excess pressure fromfreezing cylinder back to mixreservoir.
000
11 120717
X57028-XX Pump A. - Mix Simplified - Shake
Figure 5
12
X57029-XX Pump A. - Mix Simplified - Soft Serve (See Figure 6)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 - 7 X57029-XX Pump A.-MixSimplified Soft Serve
1 Delivers air and mix to freezingcylinder.
103
1 057943 Cylinder-Pump-Hopper-Soft Serve
1 Chamber to house the piston. 103
2 X55450 Pin A.-Retaining 1 Secures adaptor and valve cap incylinder.
103
3 053526 Piston 1 Moves back and forth to intakeand discharge air and mix.
103
4 020051 O-Ring 2-1/8” OD -Red
2 Provides sealed cavity insidecylinder.
000
5 056874-XX Cap-Valve 1 Provides a metered passage forair and mix. The suffix numberindicates the air orifice size.
103
6 053527 Gasket-SimplifiedPump Valve
1 Controls the flow of air and mixthrough the pump (do notlubricate).
000
7 054825 Adaptor-Mix InletSoft Serve-Red
1 Provides passageway for air andmix intake and discharge.
103
8 016132 O-Ring - 11/16 OD -Red
2 Provides a seal at each end of themix feed.
000
9 044731 Pin-Cotter 1 Secures mix inlet tube to pumpadaptor.
103
10 X41947 Shaft A.-Drive-MixPump - Hopper
1 Rotates counter-clockwise tomove piston back and forth.
103
10a 039235 Crank-Drive 1 Delivers motion to piston. 10310b 041948 Shaft-Drive 1 Delivers motion from pump motor
to crank.103
10c 048632 O-Ring - Drive Shaft 2 Provides seal to prevent mix fromleaking into rear drip pans.
000
10d 008904 O-Ring 1-3/4 1 Provides seal between crank andpump sleeve.
000
11 044641 Clip-Mix PumpRetainer
1 Secures air/mix pump to drive hubin mix reservoir.
103
12 X55974 Tube A.-Feed Hopper -Soft Serve
1 Mix and air is pumped through thistube to the freezing cylinder.
103
13 056524 Ring-Check .120 OD 1 Releases excess pressure fromfreezing cylinder back to mixreservoir.
000
13 120208
X57029-XX Pump A. - Mix Simplified - Soft Serve
Figure 6
14 120522
Mix Hopper - Top View (See Figure 7)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 X44761 Sleeve A.-Mix Pump 2 Hub used to hold the air/mix pump ina locked position.
103
2 X41348 Probe A.-Mix Out 2 Electrical device to indicate level ofmix in the hopper. Activates the MIXOUT light on front of freezer.
103
3 X51664 Housing A. Agitator(Shake)
1 Provides magnetic force to rotateagitator assembly.
103
3a4a
X41733 Magnet A.-Agitator-Inner
2 Rotates the agitator paddles bymagnetic force (included with theagitator assembly).
103
4 X51661 Housing A.-Agitator -(Soft Serve)
1 Provides magnetic force to rotateagitator assembly.
103
5 X42077 Probe A.-Mix Low 2 Electrical device to indicate level ofmix in the hopper. Activates the MIXLOW light on front of freezer.
103
6 080826 Cap-Magnet 2 Secures the agitator paddles in place(included with the agitator assembly).
103
Figure 7
15
X56652 Syrup Line Assembly - Triple Thick Shake Syrup (See Figure 8)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 053036 Ferrule-.625 ID 2 Clamps syrup hose on fitting. 0002 056675 Insert-QD-CPC-3/8 Barb
Plastic1 Connects syrup lines to front
panel.103
3 500205 O-Ring 1 Provides seal for quick disconnectfitting.
000
4 053052-9 Hose-Beverage 3/8 ID x5/8 OD
1 Delivers syrup to freezer door (9”). 000
5 056651 Fitting-Syrup Elbow 1 Connects valve to syrup line. 1036 500598 Valve-Check Duckbill 1 One way valve to direct syrup
flow.000
7 056650 Fitting-Syrup Nose(Large Slot)
1 Removeable fitting allowingaccess to duckbill valve.
103
8 053890 O-Ring-11 mm Green(Syrup Hole Plug)
1 Seals syrup hole plug in syrupport of freezer door.
000
Figure 8
16
X59304 Syrup Line Assembly - Thin Viscosity Syrup (See Figure 9)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 029834 Ferrule-.650 ID 2 Clamps syrup hose on fitting. 0002 056675 Insert-QD-CPC-3/8 Barb
Plastic1 Connects syrup lines to front
panel.103
3 500205 O-Ring 1 Provides seal for quick disconnectfitting.
000
4 500038-9 Tube-Vinyl 1 Delivers syrup to freezer door (9”). 0005 056651 Fitting-Syrup Elbow 1 Connects valve to syrup line. 1036 500598 Valve-Check Duckbill 1 One way valve to direct syrup
flow.000
7 056649 Fitting-Syrup Nose(Small Slot)
1 Removeable fitting allowingaccess to duckbill valve.
103
8 053890 O-Ring-11 mm Green(Syrup Hole Plug)
1 Seals syrup hole plug in syrupport of freezer door.
000
Figure 9
17
X58450 Syrup Line Assembly - Syrup-In-Bag Option (See Figure 10)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 024278 O-Ring-1/2 OD x .070 1 Provides a seal in the pump tubeconnection.
000
2 054526 Fitting-Male Peristaltic 1 Connects to the pump tube. 1033 053036 Ferrule-.625 ID NP
Brass2 Secures the fitting on the hose. 000
4 058451 Coupling-QD Female3/8 Barb
1 Quick disconnect fitting used forsyrup bag removal. Press thelever to detach.
103
5 058452 Coupling-QD Male 1/4Barb
1 Connects the hose from the syrupbag to the disconnect fitting.
103
6 R30314 Tube-Vinyl 3/16 ID x1/16 Wall
1 Delivers syrup from the bag to theperistaltic pump.
000
7 053052-36 Hose-Beverage 3/8 IDx 5/8 OD
1 Delivers syrup from the bag to theperistaltic pump.
000
Figure 10
18
Beater Door Assembly - Shake Side (See Figure 11)
ITEM PART NO. DESCRIPTION QTY. FUNCTION WARR.CLASS
1 032560 Seal-Drive Shaft 1 Provides seal from product insidefreezing cylinder to internal areasof freezer.
Hopper Soft Serve14 008904 O-Ring 1-3/415 016132 O-Ring-11/16 OD -
Red16 X44797 Agitator A.-Mix
Hopper
30 070423
IMPORTANT TO THE OPERATOR
Figure 19
ITEM DESCRIPTION FUNCTION1 Keypad-Shake Used for selecting operating functions on the shake side of the
machine.2 Display-Vacuum
Fluorescent Menu (VFD)Screen which displays menu options and notifies operator if afault is detected.
3 Keypad-Menu(Entry/Exit)
Used to select the Manager's Menu or to exit the Menu Display.
4 Keypad-Soft Serve Used for selecting operating functions on the soft serve side ofthe machine.
5 Standby-Soft Serve Indicates when the soft serve side is in the Standby mode.6 Standby-Shake Indicates when the shake side is in the Standby mode.7 Keypad-Topping Heater Used to activate the topping rail heaters.8 Display-LED (Brush
Clean Countdown)Displays the number of days before brush cleaning is required.
9 Keypad-Flavor Select Used for selecting the desired shake flavor to be dispensed. Alsoused for opening and closing the draw valve when cleaning,sanitizing, and priming the shake side.
10 Switch-Power When placed in the ON position, allows control panel operation.11 Keypad-Calibrate Menu Used to access the Calibrate Menu containing options for
calibrating the syrup dispensing rate or priming and flushing thesyrup lines.
12 Indicator Light-Mix Low Illuminates when the mix hopper has a low supply of mix andshould be refilled as soon as possible.
13 Indicator Light-Mix Out Illuminates when the mix hopper has an insufficient supply of mixto operate the freezer. The Auto mode will be locked out and themachine will be placed in the Standby mode.
Note: See Manager's Menu on page 78 for additional key functions when the Calibration orManager's Menu is displayed.
31
Symbol Definitions
To better communicate in the Internationalarena, the words on many of our operatorkeys have been replaced by symbols toindicate their functions. Your Taylor equipmentis designed with these International symbols.
The following chart identifies the symboldefinitions.
= AUTO
= HEAT CYCLE
= WASH
= MIX PUMP
= STANDBY (SHAKE)
= STANDBY (SOFT SERVE)
= FLAVOR SELECTION
= MIX LOW
= MIX OUT
= TOPPING HEATER-LEFT
= TOPPING HEATER-RIGHT
= CALIBRATE
= MENU DISPLAY
Power Switch
When placed in the ON position, the powerswitch allows control panel operation.
Vacuum Fluorescent Display
The vacuum fluorescent display (VFD) islocated on the front control panel. Duringnormal operation the display is blank. Thedisplay is used to show menu options andnotifies the operator if a fault is detected. OnInternational models, the display will indicatethe temperature of the mix in each hopper.
Indicator Lights
MIX LOW - When the MIX LOW symbol isilluminated, the mix hopper has a low supplyof mix and should be refilled as soon aspossible.
MIX OUT - When the MIX OUT symbol isilluminated, the mix hopper has been almostcompletely exhausted and has an insufficientsupply of mix to operate the freezer. At thistime, the AUTO mode is locked out and thefreezer will be placed in the STANDBY mode.To initiate the refrigeration system, add mix tothe mix hopper and touch the AUTOsymbol . The freezer will automatically beginoperation.
32 091002
Heat Mode Symbol
When the HEAT MODE symbol isilluminated, the freezer is in the process of aheat cycle. The heat mode symbol may beselected to start a heat cycle following afreezer soft lock condition.
For some international models, the heatsymbol can be selected to manually start aheat cycle at any time.
Brush Clean Countdown - Displays thenumber of days before the next brush cleaningis required. When the display has counteddown to “1”, the machine must bedisassembled and brush cleaned within 24hours.
Reset Mechanism
The reset button is located in the servicepanel at the rear of the machine. It protectsthe beater motor from an overload condition.Should an overload occur, the resetmechanism will trip. To properly reset thefreezer place the power switch in the OFFposition. Press the reset button firmly. Turnthe power switch to the ON position. Touchthe WASH symbol and observe thefreezer's performance. (See Figure 20.)
Figure 20
WARNING: Do not use metal objectsto press the reset button. Failure to complymay result in severe personal injury or death.
If the beater motor is turning properly, touchthe WASH symbol to cancel the cycle.Touch the AUTO symbol to resume normaloperation. If the freezer shuts down again,contact your authorized service technician.
Air/Mix Pump Reset Mechanism
The reset button for the pump is located in theservice panel at the rear of the machine. (SeeFigure 20.) The reset protects the pump froman overload condition. Should an overloadoccur, the reset mechanism will trip. To resetthe pump, press the reset button firmly.
WARNING: Do not use metal objectsto press the reset button. Failure to complymay result in severe personal injury or death.
Adjustable Draw Handle
This unit features an adjustable draw handleto provide the best portion control, giving abetter, consistent quality to your product andcontrolling costs. The draw handle should beadjusted to provide a flow rate of 5 to 7-1/2 oz.(142 to 213 g.) of product by weight per 10seconds. To INCREASE the flow rate, tightenthe screw. To DECREASE the flow rate,loosen the screw. After setting the flow rate,tighten the jam nut to secure the adjustmentscrew. (See Figure 21.)
Figure 21
33 120629
Shake Fill Level Adjustment
The portion control sensor is located under thecup holder. In front of the portion controlsensor is the portion control sensor shield.The sensor shield must be kept clean for thesensor to perform properly.
If the shakes are not filling the cup to thedesired level, clean and inspect the sensorshield. Use a clean, damp, sanitized towel togently wipe the portion control sensor shieldand remove any mix build up. Inspect thesensor shield for damage and replace, ifnecessary. (See Figure 22.)
Figure 22
The portion control sensor can be adjusted tofill the cup to the desired level. If the fill level istoo low, or if the cup is overfilling, it may benecessary to adjust the sensor position.(See Figure 23.)
Figure 23
To adjust the sensor position, perform thefollowing steps:
1. Using a crescent wrench, loosen thelocking nut on the screw adjuster belowthe sensor.
2. Turn the adjustment screw clockwise toraise the fill level, or counterclockwise tolower the fill level.
3. Once the desired fill level is achieved,tighten the locking nut.
DAILY OPENING PROCEDURES
Before performing the opening procedures,check the display panel for any errormessages. Normally the display is blankunless an operational fault has occurred. If afault has been detected, investigate the causeand follow the instructions on the displaybefore proceeding with the openingprocedures. (See Failure Messages, pages75 and 86.)
Set-Up - Complete The Following
Make sure your hands are clean and sanitizedbefore performing these next steps.
1. With the drain plugs closed, check thewater level in the two heated toppingwells. Fill the wells with water to theindicating mark on the bottom of the well.
2. Place the topping heaters in the ONposition by touching the topping heatersymbols .
Caution: As soon as the heaters are turned on,the topping wells will begin heating. Thisheating process will take approximately 2-1/2hours to reach temperature. The water level inthe wells should be checked daily.
3. Fill the topping containers with topping.Place the caramel and fudge toppingcontainers in the heated wells. Place theremaining two topping containers in theunheated wells. Cover the containers.
4. Sanitize the two topping ladles and placein the cold topping containers.
5. Fill the cup dispensers, cup lid holder, andcone dispenser.
6. To fill the cone dispenser, slide the drawerup and pull out. Push the spring guide allthe way back to its locking position. Placethe cones in the drawer and release thespring guide.
34 071022
Shake Side
1. When the heating cycle is complete, theheat cycle symbols will no longer beilluminated and the machine willautomatically enter the STANDBY mode.Prepare a small amount of KAY-5®Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
2. Remove the syrup hole plugs, the syrupvalve retainers, and the draw valve cap(spout cap) from the freezer door.Remove the o-rings from the syrup holeplugs and the draw valve cap.
3. Sanitize all o-rings, the restrictor cap,syrup hole plugs, syrup valve retainers,draw valve cap (spout cap), shake cupholder, front drip tray and splash shield, inthis solution.
4. Return to the freezer with a small amountof sanitizing solution. With a pail belowthe door spout, dip the door spout brushinto the sanitizing solution. Brush cleanthe door spout, the bottom of the drivenspinner and spinner blade, and the syrupline fittings. (See Figure 24.)
Figure 24
Note: To assure sanitary conditions aremaintained, brush clean each item for a totalof 60 seconds, repeatedly dipping the brush insanitizing solution.
5. With the syrup port brush, brush eachsyrup port hole 10 to 15 times. Dip thebrush in sanitizing solution beforebrushing each port. (See Figure 25.)
Figure 25
6. Fill the squeeze bottle with sanitizingsolution. With a pail beneath the door,insert the tube end of the squeeze bottleinto the syrup port, and squeeze the bottlefirmly. This action will force solution out ofthe adjacent port and down around thespinner. This procedure should beperformed for at least 10 seconds perport. (See Figure 26.)
Figure 26
7. Reinstall the syrup valve retainers.
8. Install the restrictor cap on the freezerdoor spout. (See Figure 27.)
Figure 27
35
9. With the pail still beneath the door,remove the syrup nose fitting from thesyrup line fitting by turning itcounter-clockwise. Hold the syrup fittingsin an “up“ position to minimize syrup loss.(See Figure 28.)
Figure 28
10. Remove the duckbill valve and o-ring fromthe syrup nose fitting. (See Figure 29.)
Figure 29
11. Using the white end of the double-endedbrush, scrub the inside of the syrup nosefitting to remove any residual particles.
12. Using a shake cup filled with KAY-5®Sanitizer (HCS) solution, rinse the syrupnose fitting thoroughly.
13. Using a clean, sanitized towel, gently wipeany syrup from the duckbill valve.
14. Using a shake cup filled with KAY-5®Sanitizer (HCS) solution, thoroughly rinsethe duckbill valve.
15. Install the duckbill valve into the syrupnose fitting with the flat end aligned withthe open slot in the syrup nose fitting.
Note: Replace the duckbill valve if it isdamaged or extends past the syrup nosefitting slot. (See Figure 30.)
Figure 30
16. Install the syrup nose fitting onto thesyrup line fitting. Tighten by hand untilsnug.
Note: The duckbill valve must be wet whenthe syrup nose fitting is installed on the syrupline fitting. The sanitized water will lubricatethe bottom flat surface and prevent theduckbill from twisting when tightening thesyrup nose fitting.
17. Inspect the duckbill valve for properinstallation inside the syrup nose fitting.The tip of the duckbill valve must be flatto seal the syrup line. (See Figure 31.)
Figure 31
If the tip is not flat, remove the syrup nosefitting and remove/reinstall the duckbillvalve. Using a shake cup filled withKAY-5® Sanitizer (HCS), rinse the syrupnose fitting to wet the bottom of theduckbill valve. Reinstall the syrup nosefitting onto the syrup line fitting. If the tipwill not remain flat when the syrup fitting isassembled, replace the duckbill valve.
36
18. Install the o-ring on the nose fitting.
19. Repeat steps 8 through 17 for all syrupflavors.
20. Each syrup flavor must be primed topurge the air out of the syrup lines. Toprime each syrup line, hold the syrup lineup, over an empty cup. (See Figure 32.)
Figure 32
21. Touch the CALIBRATION symbol todisplay the menu options. TheCALIBRATION symbol , the AUTOsymbol on the shake side, and theOPTIONAL FLAVOR symbol will beilluminated.
The screen will display the calibrationmenu options. (See Figure 33.)
UNFLAVORED DRAWSYRUP CALIBRATIONSYRUP PRIME
> EXIT
Figure 33
22. Touch the AUTO symbol or theOPTIONAL FLAVOR symbol to scrollthe arrow to SYRUP PRIME.(See Figure 34.)
UNFLAVORED DRAWSYRUP CALIBRATION
> SYRUP PRIMEEXIT
Figure 34
23. Touch the CALIBRATION symbol toenter the SYRUP PRIME mode.(See Figure 35.)
SYRUP PRIMESelect a Flavor
< Press to clear
Figure 35
24. Touch the corresponding syrup flavorsymbol . The flavor symbol should beilluminated and the syrup pump for theselected flavor will start running at themaximum speed. (See Figure 36.)
Figure 36
25. When a steady stream of syrup is flowingfrom the syrup valve and all air has beenpurged from the syrup line, touch anysyrup flavor symbol to stop the pump.
26. Repeat steps 23 - 24 to prime the rest ofthe syrup lines. After priming is complete,exit the SYRUP PRIME mode by touchingthe CALIBRATION symbol .
27. Using the squeeze bottle filled withsanitizing solution, sanitize the syrupvalve nose fittings.
37 120629
28. Lubricate the o-ring. Raise the syrup valveretainer. Install the syrup valve. Push thesyrup valve retainer down to hold thevalve in place. Repeat this procedure foreach syrup valve. (See Figure 37.)
Figure 37
Note: Do not install an empty syrup line in thefreezer door. Insert a syrup port plug in thedoor whenever a syrup line is not in use. Thiswill prevent an accumulation of mix inside thevalve fitting and the syrup line.
29. Using a clean, sanitized towel, wipe downthe freezer door, front panel, the areaaround the bottom of the freezer door,and any other areas that demonstrate abuild-up of either moisture or foodsubstance.
30. Use a clean, damp, sanitized towel togently wipe the portion control sensorshield and remove any mix build up.Inspect the sensor shield for damage andreplace, if necessary. (See Figure 38.)
Figure 38
31. Install the shake cup holder, the front driptray and the splash shield.
32. When ready to resume normal operation,touch the AUTO symbol . (SeeFigure 39.) The control has a feature inthe Manager's Menu to enable or disablethe AUTO START feature. When AUTOSTART in enabled, the machine willautomatically exit the STANDBY modeand start both sides in the AUTO mode ata designated time each day.(See page 83.)
Figure 39
Note: Placing the machine in AUTO shouldbe performed approximately 15 minutes priorto serving product.
Soft Serve Side1. Prepare a small amount of KAY-5®
Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
2. Return to the freezer with a small amountof sanitizing solution. Dip the door spoutbrush into the sanitizing solution andbrush clean the door spout, and bottom ofthe draw valve. (See Figure 40.)
Figure 40
38
Note: To assure sanitary conditions aremaintained, brush clean each item for a totalof 60 seconds, repeatedly dipping the brush insanitizing solution.
3. Using a clean, sanitized towel, wipe downthe freezer door, front panel, the areaaround the bottom of the freezer door,and any other areas that demonstrate abuild-up of either moisture or foodsubstance.
4. When ready to resume normal operation,touch the AUTO symbol . (SeeFigure 41.) The control has a feature inthe Manager's Menu to enable or disablethe AUTO START feature. When AUTOSTART in enabled, the machine willautomatically exit the STANDBY modeand start both sides in the AUTO mode ata designated time each day.(See page 83.)
Figure 41
Note: This procedure should be performed 15minutes prior to serving product.
SYRUP SYSTEM
Syrup Calibration
Calibrating the syrup flow should be performedweekly when the syrup system is cleaned. It isvital that the correct amount of syrup beincorporated into the frozen mix to obtain aquality shake.
To determine the rate of syrup flow, you willneed a calibration cup indicating fluid ounces.The proper rate of syrup flow is 1 fl. oz. (30 ml)of syrup in 5 seconds. For Triple Thick Shakesyrups, the proper syrup flow rate is 1 fl. oz.
+/- 1/8 fl. oz. (30 ml +/- 4 ml) in 7 seconds.Once this rate is set, the correct amount ofsyrup will be blended with the shake baseregardless of the size of shake served. Pleasenote that syrup calibration is critical whenchanging the promotional 4th flavor syrup.
Calibration Procedure
Syrup lines must be properly primed with syrupto eliminate air in the line before the calibrationprocedure is performed. (See the Syrup PrimingProcedures on page 40.)
1. Touch the CALIBRATION symbol todisplay the menu options. TheCALIBRATION symbol , the AUTOsymbol on the Shake side, and theOPTIONAL FLAVOR symbol will beilluminated. (See Figure 42.)
Figure 42
The screen will display the calibrationmenu options. (See Figure 43.)
UNFLAVORED DRAWSYRUP CALIBRATIONSYRUP PRIME
> EXIT
Figure 43
Note: When the CALIBRATION screen isdisplayed, the flavor selection symbols willnot raise the draw valve to dispense shakeproduct.
39
2. Touch the AUTO symbol or theOPTIONAL FLAVOR symbol to scrollthe arrow to SYRUP CALIBRATION.(See Figure 44.)
UNFLAVORED DRAW> SYRUP CALIBRATION
SYRUP PRIMEEXIT
Figure 44
3. Touch the CALIBRATION symbol toenter the syrup calibration mode.(See Figure 45.)
SYRUP CALIBRATIONSelect a Flavor
< Press to clear
Figure 45
4. Disconnect the syrup valve from thefreezer door. Raise the syrup valveretainer and pull the valve straight out.(See Figure 46.)
Figure 46
5. To calibrate the syrup dispensing rate,hold the small portion of the calibrationcup under the valve for the flavor to becalibrated. Touch the correspondingFLAVOR SELECT symbol to activatethe syrup pump and start the flow ofsyrup. When the syrup level measuresone ounce, touch the same FLAVORSELECT symbol to stop the syrup flow.
Verify the level of syrup in the cup. If themeasurement is not within thespecification, repeat step 4 for the sameflavor until the correct syrup calibration isachieved. (See Figure 47.)
Figure 47
Note: You can verify the syrup dispensingrate in the Manager's Menu. (See “VerifyCalibration” on page 80.)
Repeat steps 4 and 5 for the remainingsyrup flavors.
6. Exit the CALIBRATION mode by touchingthe CALIBRATION symbol . A blankscreen will appear and the AUTO symbol
and the OPTIONAL FLAVORsymbol will return to their normalfunction.
Note: Whenever a particular syrup line is notused, the syrup hole plug found in the spareparts kit must be installed. Place the syruphole plug o-ring into the groove of the syruphole plug, and lubricate. Install the hole plug inthe door. Lower the retaining pin to secure theplug in place.
40
Syrup Priming Procedure
The purpose of priming the syrup line is toeliminate any air in the syrup delivery system.Air in the syrup line can cause irregular shakeblending, flavor carry-over, and syrup leakingfrom the door spout after the draw valve hasclosed. Each time a syrup container is drainedor replaced, prime the syrup system until allthe air has been removed and the syrup flowis uniform.
1. Retrieve a full syrup container from thedry storage area.
2. Shake the syrup container prior toopening it. Open the full syrup container.
3. Pull the feed tube from the empty syrupcontainer and clean the outside of thefeed tube with a clean, sanitized towel.
For syrup bag system: Disconnect the emptybag and clean the hose connector fitting with aclean, sanitized towel. Attach the hoseconnector fitting to a full bag of syrup. Placethe bag on the shelf in the syrup compartment.Make sure the hose is not pinched and thereare no kinks in the tubing.
4. Place the feed tube into the full syrupcontainer and replace the syrup containerin the syrup cabinet.
5. Dispose of the empty syrup container.
6. Prime the syrup line by removing thesyrup valve from the freezer. Hold it overan empty cup.
7. Touch the CALIBRATION symbol todisplay the menu options. TheCALIBRATION symbol , the AUTOsymbol on the shake side, and theOPTIONAL FLAVOR symbol will beilluminated.
The screen will display the calibrationmenu options. (See Figure 48.)
UNFLAVORED DRAWSYRUP CALIBRATIONSYRUP PRIME
> EXIT
Figure 48
8. Touch the AUTO symbol or theOPTIONAL FLAVOR symbol to scrollthe arrow to SYRUP PRIME.(See Figure 49.)
UNFLAVORED DRAWSYRUP CALIBRATION
> SYRUP PRIMEEXIT
Figure 49
9. Touch the CALIBRATION symbol toenter the SYRUP PRIME mode.(See Figure 50.)
SYRUP PRIMESelect a Flavor
< Press to clear
Figure 50
10. Touch the corresponding syrup flavorsymbol . The flavor symbol should beilluminated and the syrup pump for theselected flavor will start running at themaximum speed. (See Figure 51.)
Figure 51
11. When a steady stream of syrup is flowingfrom the syrup valve and all air has beenpurged from the syrup line, touch anysyrup flavor symbol to stop the pump.
12. Repeat steps 10 -11 for any other syruplines to be primed, or exit the SYRUPPRIME mode by touching theCALIBRATION symbol .
41 120312
DAILY CLOSING PROCEDURES
This procedure must be done at the close ofbusiness.
Shake SideImportant: Fill the mix hopper with mix up tothe fill level indicator on the agitator paddle.(See Figure 52.)
Figure 52
Both sides of the freezer must be in the AUTOmode (AUTO symbol is illuminated) or inthe STANDBY mode (STANDBY symbolsand are illuminated) before the HEAT cyclemay be started.Note: If the BRUSH CLEAN COUNTERdisplay has counted down to 1 day, do notadd mix. The machine must be disassembledand brush cleaned within 24 hours.1. Remove the hopper cover, shake cup
holder, splash shield and drip pans.
Make sure your hands are clean andsanitized before performing these nextsteps.
Note: Select the CALIBRATION symbol tostop agitator movement for 10 seconds. Selectthe CALIBRATION symbol again to exit thecalibration mode. The agitator willautomatically restart after 10 seconds.2. Remove the agitator from the mix hopper
and the restrictor cap from the shakefreezer door spout.
3. Take the agitator, hopper cover, shakecup holder, drip pans, front drip tray,splash shield and restrictor cap to the sinkfor further cleaning and sanitizing.
Take the syrup hole plugs, spout cap, andspout cap o-ring to the sink for furthercleaning and sanitizing.
4. Rinse these parts in cool, clean water.Draw a small amount of SolidSense™ AllPurpose Super Concentrate (APSC)(HCS) cleaning solution from the sinkproportioner and brush clean the parts.
5. Place the restrictor cap, front drip tray,shake cup holder and splash shield on aclean, dry surface to air-dry overnight oruntil the heating cycle is complete.
6. Prepare a small amount of KAY-5®Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
7. Sanitize the syrup hole plugs, spout cap,spout cap o-ring, drip pan, agitator, andhopper cover.
8. Install the agitator back onto the agitatordrive shaft housing. Replace the hoppercover. (See Figure 53.)
Figure 53
Important: If you do not install the agitatorcorrectly, the machine will fail the heat cycleand will lock out in the morning.
42
9. Remove the syrup lines from the freezerdoor. (See Figure 54.)
Figure 54
10. Return to the freezer with a small amountof cleaning solution. With a pail below thedoor spout, dip the door spout brush intothe cleaning solution and brush clean thesyrup ports in the freezer door, door spoutand bottom of the driven spinner, spinnerblade, and syrup line fittings.(See Figure 55.)
Figure 55
Note: To assure sanitary conditions aremaintained, brush each item for a total of 60seconds, repeatedly dipping the brush incleaning solution.
11. With the syrup port brush, brush eachsyrup port hole 10 to 15 times. Dip thebrush in the cleaning solution beforebrushing each port. (See Figure 56.)
Figure 56
12. With sanitized hands, remove the syrupvalve retainers. Brush clean the retainersand retainer holes. Replace the syrupvalve retainers.
13. Fill the squeeze bottle with cleaningsolution. With a pail beneath the door,insert the tube end of the squeeze bottleinto the syrup ports, and squeeze thebottle firmly. This action will force solutionout of the adjacent port and down aroundthe spinner. This procedure should beperformed for at least 10 seconds perport. (See Figure 57.)
Figure 57
43 120629
14. Place the spout cap o-ring in the spoutcap. Fill the spout cap with sanitizingsolution. Install the spout cap over theend of the door spout. (See Figure 58.)
Figure 58
15. Raise each retainer pin. Install the syruphole plugs in the syrup ports in the freezerdoor. Lower the retainer pins to securethe hole plugs in the door.(See Figure 59.)
Figure 59
16. Fill the squeeze bottle with sanitizingsolution. Hold the bottle over a pail.Squeeze the bottle and thoroughly rinsethe slot of each syrup nose fitting.(See Figure 60.)
Figure 60
17. Wipe the outside of each syrup nosefitting with a sanitized towel.
18. Using a clean, sanitized towel, wipe downthe freezer door, front panel, the areaaround the bottom of the freezer door,and any other areas that demonstrate abuild-up of either moisture or foodsubstance.
19. Use a clean, damp, sanitized towel togently wipe the portion control sensorshield and remove any mix build up.Inspect the sensor shield for damage andreplace, if necessary. (See Figure 61.)
Figure 61
44 080723
Soft Serve Side
This procedure must be done at the close ofbusiness.
Important: Fill the mix hopper with mix up tothe fill level indicator on the agitator paddle.(See Figure 62.)
Figure 62
Both sides of the freezer must be in the AUTO(AUTO symbol is illuminated) or in theSTANDBY mode (STANDBY symbols and
are illuminated) before the HEAT cycle maybe started.
Note: If the BRUSH CLEAN COUNTERdisplay has counted down to one day, do notadd mix. The machine must be disassembledand brush cleaned within 24 hours.
1. Place the topping heaters in the OFFposition by touching the heatersymbols . The symbols will not beilluminated when the heaters are off.(See Figure 63.)
Figure 63
2. Remove the hopper cover.
MAKE SURE YOUR HANDS ARE CLEAN ANDSANITIZED BEFORE PERFORMING THESENEXT STEPS.
Note: Select the CALIBRATION symbol tostop agitator movement for 10 seconds. Selectthe CALIBRATION symbol again to exit thecalibration mode. The agitator willautomatically restart after 10 seconds.
3. Remove the agitator from the mix hopper.
4. Take the agitator and hopper cover to thesink for further cleaning and sanitizing.
5. Rinse these parts in cool, clean water.
6. Draw a small amount of SolidSense™ AllPurpose Super Concentrate (APSC)(HCS) cleaning solution from the sinkproportioner and brush clean the parts.
7. Prepare a small amount of KAY-5®Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM). Sanitize the agitator and hoppercover.
8. Install the agitator back onto the agitatordrive shaft housing. Replace the hoppercover.
Important: If you do not install the agitatorcorrectly, the machine will fail the heat cycleand will lock out in the morning.
9. Return to the freezer with a small amountof cleaning solution. Dip the door spoutbrush into the cleaning solution and brushclean the door spout and bottom of thedraw valve.
Note: To assure sanitary conditions aremaintained, brush each item for a total of 60seconds, repeatedly dipping the brush incleaning solution. (See Figure 64.)
Figure 64
45
10. Remove, clean and reinstall the long drippan through the front panel.(See Figure 65.)
Figure 65
11. Remove, clean and reinstall the two shortdrip pans in the rear panel.
12. Remove, clean and reinstall the twonotched drip pans in the left and right sidepanels. (See Figure 66.)
Figure 66
13. Using a clean, sanitized towel, wipe downthe freezer door, front panel, the areaaround the bottom of the freezer door,and any other areas that demonstrate abuild-up of either moisture or foodsubstance.
The heat cycle will start at the AUTO HEATTIME setting in the Manager's Menu.(See page 83).
There are three phases of the heat cycle:Heating, Holding and Cooling. Each phasehas a time limit. If any one of the three phasesfail to reach the proper temperatures within thetime limit, the cycle will automatically abort andreturn to the STANDBY mode.
A failure message will appear on the vacuumfluorescent display (VFD) to inform theoperator that the machine did not successfullycomplete the heat treatment cycle. Theproduct may not be safe to serve. The freezerwill be locked out (softlock) of the AUTOmode. The operator will be given the option ofselecting the HEAT symbol which will begina new heat cycle, or touching the WASHsymbol which will place the side(s) into theOFF mode to allow a brush clean of themachine.
Note: Once the heating cycle has started, itcannot be interrupted. The heating cycle willtake a maximum of 4 hours to complete withfull hoppers.
DO NOT attempt to draw product ordisassemble the unit during the HEAT cycle.The product is hot and under extremepressure.
When the heating cycle is complete, thecontrol will return to the STANDBY mode. TheSTANDBY symbols and will beilluminated.
46 080225
SCHEDULED MAINTENANCE -SYRUP SYSTEM
Syrup Pump Tube Removal
The syrup pump tubes should be replaced atleast once a year, or sooner if unable tocalibrate the syrups.
1. Remove the syrup feed tubes from thesyrup containers. Wipe the outside of thefeed tubes with a clean, sanitized towel.
For Syrup Bag System: Disconnect thesyrup bag fitting from each bag.
2. Remove the syrup containers and thepump cover tray from inside the cabinet.
3. Place the syrup feed tubes in a pail ofSolidSense™ All Purpose SuperConcentrate (APSC) (HCS). One packetin 2-1/2 gal. (9-1/2 liters) of water = 100PPM. To avoid contamination, cover thesyrup containers with a plastic wrap.
For Syrup Bag System: Place the syruphose with the bag connection fitting in apail of SolidSense™ All Purpose SuperConcentrate (APSC) (HCS).
4. Raise the retainer and remove the syrupvalve from the freezer door. Place thevalve in a pail located under the drawvalve.
5. Select the CALIBRATION symbol onthe control panel to display the menuoptions.
6. Touch the AUTO symbol to move thearrow to SYRUP PRIME. Touch theCALIBRATION symbol again to displaythe SYRUP PRIME screen.
7. Select the FLAVOR SELECT symbolfor the corresponding syrup valve to startthe flow of SolidSense™ All PurposeSuper Concentrate (APSC) (HCS)through the syrup line.
8. Allow the cleaning solution to flow until allof the syrup is flushed from the line.
9. Once the line is free of syrup, remove thesyrup feed tube from the cleaning solutionand continue to run the pump until the
syrup line is free from liquid. Select theFLAVOR SELECT symbol to stop thepump.
10. Repeat steps 3 through 9 using clean,warm water to flush the cleaning solutionfrom the syrup line.
11. Repeat steps 3 through 9 usingKAY-5® Sanitizer (HCS). One packet in2-1/2 gal. (9-1/2 liters) of water = 100PPM.
12. Open the pump by pushing up on thehinged cover. (See the arrow inFigure 67.)
Figure 67
13. Grasp the pump tube by both ends andremove it from the pump body.(See Figure 68.)
Figure 68
47 080225
14. Remove the clips from their respectivecollars.
15. Remove the fittings from the pump tube.
Pump Tube Installation
1. Lubricate the o-rings on the syrup linefittings with Taylor Lube HP.(See Figure 69.)
Figure 69
2. Press the fittings into the new pump tube.
3. Install the clips into their respectivecollars.
4. Using your hands, rotate the pump rollersso they are in the 10 and 2 o'clockposition.
5. Place the tube assembly into the pumpbody. (Make sure the syrup lines arepushed through the rear of the cabinet.)
6. Push down on the top of the pump toclose it.
7. Replace the pump cover tray and thesyrup containers.
8. Prime the syrup lines.
9. Calibrate the syrup system according tothe instructions on page 38.
Syrup Line Cleaning/Sanitizing - Weekly
1. Remove the syrup feed tubes from thesyrup containers. Wipe the outside of thefeed tubes with a clean, sanitized towel.
For Syrup Bag System: Disconnect eachsyrup bag and clean the hose connectorfitting with a clean, sanitized towel.
2. Draw two gallons of SolidSense™ AllPurpose Super Concentrate (APSC)(HCS) cleaning solution from the sinkproportioner into a pail. Place the syrupfeed tubes in the pail.
For Syrup Bag System: Place the syruphose with the bag connection fitting in thepail of SolidSense™ All Purpose SuperConcentrate (APSC) (HCS).
3. Raise the retainer and remove the syrupvalve from the freezer door. Place thevalve in a pail located under the drawvalve.
4. Select the CALIBRATION symbol onthe control panel to display the menuoptions.
5. Touch the AUTO symbol to move thearrow to SYRUP PRIME. Touch theCALIBRATION symbol again to displaythe SYRUP PRIME screen.
6. Select the FLAVOR SELECT symbolfor the corresponding syrup valve to startthe flow of SolidSense™ All PurposeSuper Concentrate (APSC) (HCS)through the syrup line.
7. Allow the cleaning solution to flow until allthe syrup is flushed from the line.
8. Touch the FLAVOR SELECT symbolto stop the flow of cleaning solution.
9. Repeat steps 2 - 8 using clean, warmwater to flush the cleaning solution fromthe syrup line.
10. Repeat steps 2 - 8 using KAY-5®Sanitizer (HCS) [1 packet in 2-1/2 gal.(9-1/2 liters) of water = 100 PPM.]
11. Remove the syrup nose fitting from thesyrup valve by turning the capcounter-clockwise.
12. Remove the duckbill valve and o-ring fromthe syrup nose fitting.
13. Using the white end of the double-endedbrush, scrub the inside of the syrup nosefitting and the syrup line fitting to removeany residual particles.
48
14. Using a shake cup filled with KAY-5®Sanitizer (HCS), rinse the syrup valvefitting thoroughly.
15. Using a clean, sanitized towel, gently wipeany syrup from the duckbill valve.
16. Install the duckbill valve into the syrupnose fitting, with the flat end aligned withthe open slot in the syrup nose fitting.
Note: Replace the duckbill valve if it isdamaged or extends past the syrup nosefitting slot. (See Figure 30.)
Figure 70
17. Install the syrup nose fitting onto thesyrup line fitting. Tighten by hand untilsnug.
Note: The duckbill valve must be wet whenthe syrup nose fitting is assembled on thesyrup line fitting. The sanitized water willlubricate the bottom flat surface and preventthe duckbill from twisting when the the syrupnose fitting is tightened.
18. Inspect the duckbill valve for properinstallation inside the syrup nose fitting.The tip of the duckbill valve must be flatto seal the syrup line. (See Figure 31.)
Figure 71
If the tip is not flat, remove the syrup nosefitting and remove/reinstall the duckbillvalve. Using a shake cup filled withsanitizing solution, rinse the syrup nosefitting to wet the bottom of the duckbillvalve. Reinstall the syrup nose fitting ontothe syrup line fitting. If the tip will notremain flat when the syrup fitting isassembled, replace the duckbill valve.
19. Install the o-ring on the syrup nose fitting.
20. Repeat steps 3 through 19 for all syrupflavors.
21. Remove the pick up tubes from the pail ofKAY-5® Sanitizer (HCS) and allow themto drain.
22. Place all the pick up tubes into the syrupcontainers. Ensure the syrup lines matchtheir respective flavors.
For Syrup Bag System: Attach the bagconnector fitting to the proper syrup flavor.
23. Select the CALIBRATION symbol onthe control panel to display the menuoptions.
24. Touch the AUTO symbol to move thearrow to SYRUP PRIME. Touch theCALIBRATION symbol again to displaythe Syrup Prime screen.
25. Select the FLAVOR SELECT symbolfor the corresponding syrup valve to startthe flow of syrup.
26. Allow the syrup to flow until all of theKAY-5® Sanitizer (HCS) and air ispurged from the line.
27. Touch the FLAVOR SELECT symbolto stop the flow of syrup.
28. Lubricate the o-ring on the syrup nosefitting. Install the syrup valve into theshake door and secure the valve bylowering the retainer.
29. Repeat steps 21 - 28 for all syrupflavors.
30. Clean the syrup cabinet interior with aclean, sanitized towel. Spray resistantareas with KAY-5® Sanitizer (HCS).
49 120228
SYRUP TOPPING PUMP
Syrup Topping Pump Disassembly
Before the first use, and after use weekly,disassemble and clean the pump.
1. Flush and rinse the pump in a container ofwarm water. Place the lower end of thepump into the water container. Operatethe pump until only warm water flows fromthe discharge tube.
2. Remove the pump from the container ofwater for disassembly.
3. Remove the plunger assembly from thepump body by turning the plunger nutcounterclockwise. (See Figure 72.)
Figure 72
4. To remove the knob, compress the springby holding the nut and pressing on theend of the plunger. Turn the knobcounterclockwise. (See Figure 73.)
Figure 73
5. Remove the plunger nut, tube, and insertfrom the plunger assembly.(See Figure 74.)
Figure 74
6. Remove the spring and washer from theplunger assembly. (See Figure 75.)
Figure 75
7. Remove the seal assembly from theplunger assembly. (See Figure 76.)
Figure 76
50
8. Remove the o-ring from the seal.(See Figure 77.)
Figure 77
9. Remove the discharge tube lock nut byturning it counterclockwise and sliding itoff the discharge tube. (See Figure 78.)
Figure 78
10. Remove the lid by sliding it off thedischarge tube.
11. Remove the cylinder from the valve bodyby turning it counterclockwise(See Figure 79.)
Figure 79
12. Remove the discharge tube from thevalve body by turning it counterclockwise.(See Figure 80.)
Figure 80
13. Remove the 1-5/16” o-ring from the valvebody and remove the 1” o-ring from thedischarge tube.
Cleaning the Syrup Pump
1. Wash and scrub all parts in SolidSense™All Purpose Super Concentrate (APSC)(HCS).
2. Insert the black shielded brush throughthe tip of the discharge tube. Move thebrush back and forth to scrub the tip ofthe discharge tube. (See Figure 81.)
Figure 81
3. Advance the brush completely throughthe discharge tube and pull the brushfrom the bottom of the tube.
51
4. Insert the black shielded brush into thetop side of the inlet valve. Scrub this area,specifically around the steel ball.(See Figure 82.)
Figure 82
5. Insert the black shielded brush into thetop side of the outlet valve. Scrub thisarea, specifically around the steel ball.(See Figure 83.)
Figure 83
6. Insert the black shielded brush, by thenon-bristle end, into the passagewaybetween the inlet valve and the outletvalve. (See Figure 84.)
Figure 84
7. Move the brush back and forth to scrubthis passageway. Advance the brushcompletely, and pull the brush out of thevalve body. (See Figure 85.)
Figure 85
8. Insert the black shielded brush into thebottom side of the inlet valve. Move thebrush back and forth to scrub this area,specifically around the steel ball.(See Figure 86.)
Figure 86
9. Advance the brush completely throughthe inlet valve, and pull the brush out ofthe valve body.
10. Rinse all parts with clear water.
11. Sanitize the parts in KAY-5® Sanitizer(HCS). Allow the parts to air dry aftersanitization.
52 120228
Syrup Topping Pump Assembly
After pump disassembly and cleaning iscomplete, assemble the pump.
1. Lubricate and install the seal o-ring intothe seal. (See Figure 87.)
Figure 87
2. Install the seal assembly onto the pistonend of the plunger assembly.
3. Install the washer and spring onto theplunger assembly. (See Figure 88.)
Figure 88
4. Install the plunger insert into the plungertube by positioning the end of the insertwith small hole and beveled edge to enterthe plunger tube first. (See Figure 89.)
Figure 89
5. Install the plunger nut onto the plungertube. (See Figure 90.)
Figure 90
6. Install the flared end of the plunger tube(assembled with insert and nut) onto theplunger assembly. (See Figure 91.)
Figure 91
7. Holding the nut, press the end of theplunger to compress the spring until thethreaded end of the stem projects throughthe opening on the plunger tube. Installthe knob onto the threaded end of theplunger assembly and tighten the knob byturning it clockwise. (See Figure 92.)
Figure 92
53
8. Lubricate and install the 1” o-ring onto thegroove provided on the discharge tube.(See Figure 93.)
Figure 93
9. Lubricate and install the 1-5/16” o-ring intothe valve body. (See Figure 94.)
Figure 94
10. Install the discharge tube onto the smalleropening in the valve body by aligning theflats on the discharge tube with thelocking grooves on the valve body. Pushdown the discharge tube until it is seatedinto the valve body opening. Turn thedischarge tube clockwise to fully engage itinto locking grooves on the valve body.
11. Install the cylinder onto the larger openingin the valve body by tilting the cylinderaway from the discharge tube and slidingthe widest section of flange under thecenter locking groove on the valve body.Align the tabs on the cylinder with thelocking grooves on the valve body. Turnthe cylinder clockwise until the tabs fullyengage into the locking grooves on thevalve body.
12. Install the lid by inserting the dischargetube through the smaller hole in the lid.Slide the lid until the larger hole fitsaround the top of the cylinder. Thedischarge tube lock nut will secure the lidin position.
13. Install the discharge tube lock nut andtighten, by turning it clockwise.
14. Lubricate the seal assembly and installthe plunger assembly into the cylinderopening in the pump body.(See Figure 95.)
Figure 95
15. Tighten the plunger nut by turning itclockwise. (See Figure 96.)
Figure 96
54 070423
MANUAL BRUSH CLEANING
This Procedure Must Be Completed Every TwoWeeks!
ALWAYS FOLLOW LOCAL HEALTH CODES.
To disassemble the Model C602, the followingitems will be needed:
S Two cleaning and sanitizing pails foreach side of the freezer
S Necessary brushes (provided withfreezer)
S SolidSense™ All Purpose SuperConcentrate (APSC) (HCS)
S KAY-5® Sanitizer (HCS)S Clean, sanitized towelsS Parts trays
Draining Product From The FreezingCylinder
To drain the product from the freezingcylinders on both sides of the machine, thesteps will be the same. Therefore, first drainthe product from the shake side, then go backand duplicate these procedures for the softserve side.
1. Place the heater topping switches in theOFF position by touching the heatersymbols . The symbols will not beilluminated when the heaters are off.
2. Cancel automatic operation by touchingthe AUTO symbol . (See Figure 97.)
Figure 97
3. Shake Side Only: Remove the shake cupholder. Set it aside for cleaning later withall parts.
4. Remove the hopper cover and agitator.Take these parts to the sink to wash, rinseand sanitize.
5. With a pail beneath the door spout, touchthe WASH and PUMP symbols andopen the draw valve. (Shake Side:Touch any flavor selection symbol toopen the draw valve.)
6. Drain the product from the freezingcylinder and the mix hopper.(See Figure 98.)
Figure 98
7. When the flow of product stops, touch theWASH and PUMP symbols ,cancelling the WASH and PUMP modes.The shake draw valve will automaticallyclose when the WASH operation iscancelled.
8. Remove the locking clip, mix feed tube,pump clip and the assembled air/mixpump. Place the parts into the parts tray.
9. Shake Side Only: Remove the syruplines from the freezer door by raising thesyrup valve retainers and pulling thevalves straight out of the door. Insert thesyrup hole plugs in the syrup ports. Lowerthe retainer pins to secure the hole plugsin the door.
Repeat steps 2 through 7 for the soft serveside of the freezer.
55 130930
Rinsing
1. Pour two gallons (7.6 liters) of cool, cleanwater into the shake mix hopper. With thewhite hopper brush, scrub the mix hopper,mix level sensing probes and the outsideof the agitator drive shaft housing. Usingthe double ended brush, brush clean themix inlet hole. (See Figure 99.)
Figure 99
Note: Do not brush clean the mix inlet holewhile the machine is in the WASH mode.
2. With a mix pail beneath the door spout,touch the WASH symbol .(See Figure 100.)
Figure 100
3. Open the draw valve on the freezer door.Drain all the rinse water from the doorspout, close the draw valve, and touch theWASH symbol, cancelling the washmode. (Note: The shake draw valve willautomatically close when the WASHoperation is cancelled.)
4. Repeat this procedure using clean, warmwater, until the water being discharged isclear.
Repeat steps 1 through 4 for the soft serveside of the freezer.
Cleaning and Sanitizing
1. Draw 2 gallons (7.6 liters) ofSolidSense™ All Purpose SuperConcentrate (APSC) (HCS) cleaningsolution from the sink proportioner.
2. Pour the 2 gallons (7.6 liters) of cleaningsolution into the hopper and allow it toflow into the freezing cylinder.
3. Using the white hopper brush, clean themix hopper, mix level sensing probes andthe outside of the agitator drive shafthousing. Using the double ended brush,clean the mix inlet hole.
Note: Do not brush clean the mix inlet holewhile the machine is in the WASH mode.
4. Touch the WASH symbol . This willcause the cleaning solution in the freezingcylinder to come in contact with all areasof the freezing cylinder.
5. Place an empty pail beneath the doorspout.
6. Open the draw valve on the freezer doorand draw off all the solution.
7. Once the cleaner stops flowing from thedoor spout, close the draw valve andtouch the WASH symbol , cancellingthe wash mode. (Note: The shake drawvalve will automatically close when theWASH operation is cancelled.)
8. Pour two gallons (7.6 liters) of cool, cleanwater into the shake mix hopper andrepeat steps 3 - 7.
56
9. Prepare 2.5 gallons (9.5 liters) of KAY-5®Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
10. Pour the sanitizing solution into thehopper and repeat steps 4 through 7.
11. Repeat steps 1 through 10 for the softserve side of the freezer.
Disassembly - Shake Side
Note: Failure to remove the parts specifiedbelow for brush cleaning and lubrication willresult in damage to the machine. These partsmust be removed every 14 days or themachine will lock out and will not operate.
1. Be sure the power switch is in the OFFposition. (See Figure 101.)
Figure 101
2. Remove the hole plugs from the syrupports, and remove the restrictor cap fromthe bottom of the door spout.
3. Remove the spinner blade from thebottom of the door spout by lifting up thelocking collar on the spinner coupling andpulling down the blade.
4. Remove the handscrews, freezer door,beater assembly, drive shaft, drive shaftseal, and scraper blades from the freezingcylinder.
5. Remove the drive shaft seal from thedrive shaft.
6. Remove the freezer door o-ring, frontbearing, retainer pins, and the draw valvespinner assembly.
7. Remove the driven spinner from the drawvalve by grasping the draw valve andpulling the driven spinner out. Remove thespinner shaft seal. (See Figure 102.)
Figure 102
8. Remove the two o-rings from the drawvalve.
Note: To remove o-rings, use a clean,sanitized towel to grasp the o-ring. Applypressure in an upward direction until the o-ringpops out of its groove. With the other hand,push the top of the o-ring forward and it willroll out of the groove and can easily beremoved. If there is more than one o-ring to beremoved, always remove the rear o-ring first.This will allow the o-ring to slide over theforward o-rings without falling into the opengrooves.
9. From the shake pump cylinder, removethe retaining pin, mix inlet adaptor, valvecap, pump gasket, and the piston.Remove the o-ring from the piston andvalve cap.
57 050801
10. Remove the pump drive shaft from thedrive hub in the rear wall of the mixhopper. (See Figure 103.)
Figure 103
Remove the two small o-rings and onelarge o-ring from the pump drive shaft.
Disassembly - Soft Serve Side
Note: Failure to remove the parts specifiedbelow for brush cleaning and lubrication willresult in damage to the machine. These partsmust be removed every 14 days or themachine will lock out and will not operate.
1. Be sure the power switch is in the OFFposition.
2. Remove the handscrews, freezer door,beater, scraper blades, and drive shaftwith drive shaft seal from the freezingcylinder.
3. Remove the scraper blade clips from thescraper blades.
4. Remove the drive shaft seal from thedrive shaft.
5. From the soft serve pump cylinder,remove the retaining pin, mix inletadaptor, valve cap, pump gasket, and thepiston. Remove the o-ring from the pistonand valve cap.
6. Remove the freezer door gasket, frontbearing, pivot pin, draw handle, and drawvalve. Remove the three o-rings from thedraw valve.
Note: DO NOT attempt to remove the stardesign from the door. The star design is partof the door and is NOT a removeable piece.(See Figure 104.)
Figure 104
7. Remove the pump drive shaft from thedrive hub in the rear wall of the mixhopper. (See Figure 105.)
Figure 105
Remove the two small o-rings and onelarge o-ring from the pump drive shaft.
8. Remove the front drip tray and splashshield. Remove the ladles from the twocold topping containers.
9. Remove the long drip pan from the frontpanel. Take it to the sink for cleaning.(See Figure 106.)
Figure 106
58
10. Remove the two short drip pans from therear panel. Remove the two notched drippans from the left and right side panels.Take them to the sink for cleaning.(See Figure 107.)
Figure 107
Note: If the drip pans are filled with anexcessive amount of mix, it is an indicationthat the drive shaft seal(s), or o-ring(s) shouldbe replaced or properly lubricated.
Brush Cleaning
We recommend brush cleaning all the shakeparts, then go back and duplicate these steps(where they apply) for brush cleaning all thesoft serve parts. By doing so, you will notconfuse or interchange these parts forassembly the next morning. Place the parts intheir proper place in the parts tray.
1. From the sink proportioner drawSolidSense™ All Purpose SuperConcentrate (APSC) (HCS) solution intoa sink.
Make sure all brushes provided with thefreezer are available for brush cleaning.
2. Thoroughly brush clean all disassembledparts and parts trays in the cleaningsolution, making sure all lubricant and mixfilm is removed. Be sure to brush allsurfaces and holes, especially the holes inthe pump components and the smallsyrup holes in the shake freezer door.
3. Rinse all parts with clean, warm water,one tray at a time, including the tray.
4. Return to the freezer with a small amountof cleaning solution. Using the blackbrush, clean the rear shell bearings at theback of the freezing cylinders.(See Figure 108.)
Figure 108
5. Using the black brush, clean the drive hubopenings in the rear wall of the mixhoppers. (See Figure 109.)
Figure 109
6. Using the double end brush, brush cleanthe syrup line fittings.
7. Prepare a sink with KAY-5® Sanitizer(HCS) solution. Use one packet in 2.5gallons (9.5 liters) of water (100 PPM).
8. Repeat step 3 with the sanitizing solution.
9. Sanitize all parts in the KAY-5® Sanitizer(HCS) solution for a minimum of 1 minute.
10. Place disassembled parts on clean andsanitized parts trays.
11. Wipe all exterior surfaces of the freezerwith a clean, sanitized towel.
12. Repeat steps 1 through 10 for the softserve side of the freezer.
59
EQUIPMENT SET-UP
Freezing Cylinder Assembly - Shake Side
Make sure the power switch is in theOFF position. Failure to follow this instructionmay result in severe personal injury fromhazardous moving parts.
With the parts tray available for the shakeside:
1. Before installing the shake beater driveshaft, lubricate the groove on the beaterdrive shaft. Slide the beater drive shaftboot seal over the small end of the beaterdrive shaft and engage into the groove onthe shaft. Heavily lubricate the insideportion of the boot seal and also lubricatethe flat end of the boot seal that comes incontact with the rear shell bearing. Applyan even coat of lubricant to the shaft. DONOT lubricate the square end.(See Figure 110.)
Figure 110
Note: When lubricating parts, use anapproved food grade lubricant (example:Taylor Lube HP).
Note: To ensure that the mix does not leakout of the back of the freezing cylinder, themiddle section of the boot seal should beconvex or extend out from the seal. If themiddle section of the boot seal is concave orextending into the middle of the seal, turn theseal inside out. (See Figure 111.)
Figure 111
2. Install the shake beater drive shaftthrough the rear shell bearing in thefreezing cylinder and engage the squareend firmly into the drive shaft coupling. Besure the drive shaft fits into the drivecoupling without binding.(See Figure 112.)
Figure 112
3. Check scraper blades for any nicks orsigns of wear. If any nicks are present,replace the blades.
Note: Shake side scraper blades should bereplaced every 6 months.
60
If the blades are in good condition, placeeach scraper blade over the holding pinson the beater assembly. (See Figure 113.)
Figure 113
Note: The holes in the scraper blade must fitover the pins to prevent damage.
4. Holding the blades on the beaterassembly, insert the beater assembly inthe freezing cylinder. Engage the shaftend firmly into the drive shaft socket.(See Figure 114.)
Figure 114
Note: When properly seated, the beater willnot protrude beyond the front of the freezingcylinder.
5. Assemble the draw valve spinnerassembly. Inspect draw valve o-rings forcuts or nicks. (Replace if cut or nicked.) Ifdraw valve o-rings are in good condition,slide the 2 o-rings into the grooves of thedraw valve and lubricate.(See Figure115.)
Figure 115
6. Lubricate the outer diameter of thespinner shaft seal. Fill the cups on eachend of the seal with lubricant.(See Figure 116.)
Figure 116
61 070228
7. Insert the spinner shaft seal into thebottom of the draw valve as far as it willgo. The spinner shaft seal should fit intothe seal groove located inside the drawvalve cavity. (See Figure 117.)
Figure 117
Important: Inspect to see that thespinner shaft seal is correctly installed inthe groove. A worn, missing, or improperlyinstalled spinner shaft seal will causeproduct leakage out the top of the drawvalve.
8. Lubricate the smaller end of the drivenspinner. (See Figure 118.)
Figure 118
9. Squeezing the split end together, insertthe driven spinner through the metalopening of the draw valve until it snapsinto place. (See Figure 119.)
Figure 119
10. Insert and align the draw valve spinnerassembly into the shake door as shown.(See Figure 120.)
Figure 120
62
11. Place the freezer door o-ring into thegroove on the back of the freezer door.Lubricate the outside diameter of the frontbearing. Slide the front bearing into thedoor hub. (See Figure 121.)
Figure 121
Note: If necessary, put two small spots oflubricant at the 10 o'clock and 2 o'clockpositions on the upper portion of thefreezer door o-ring to keep it in place.
12. Install the shake freezer door. Position thefreezer door on the four studs on the frontof the freezing cylinder. Align the top ofthe draw valve with the valve lifterbracket. Install the handscrews (shorthandscrews at the bottom of the door).Tighten equally in a criss-cross pattern toinsure the door is snug. Do notover-tighten. (See Figure 122.)
Figure 122
13. Lubricate the shaft of the spinner blade upto the groove. (See Figure 123.)
Figure 123
14. Insert the spinner blade shaft into thecenter of the driven spinner, and throughthe draw valve cavity until the shaftappears at the top of the draw valve. Thespinner blade must be aligned andengaged to the driven spinner at thebottom. This allows the spinner shaft toraise high enough to be engaged into thespinner coupling at the top.(See Figure 124.)
Figure 124
63 040803
15. Raise the locking collar of the spinnercoupling and insert the spinner shaft intothe cavity of the coupling until the lockingcollar can drop into the locked position.(See Figure 125.)
Figure 125
16. Snap the restrictor cap over the end of thedoor spout and install the syrup valveretainer pins. (See Figure 126.)
Figure 126
Freezing Cylinder Assembly - Soft ServeSide
Make sure the power switch is in theOFF position. Failure to follow this instructionmay result in severe personal injury fromhazardous moving parts.
With the parts tray available for the soft serveside:
1. Before installing the soft serve beaterdrive shaft, lubricate the groove on thebeater drive shaft. Slide the beater driveshaft boot seal over the small end of thebeater drive shaft and engage into thegroove on the shaft. Heavily lubricate theinside portion of the boot seal and alsolubricate the flat end of the boot seal thatcomes in contact with the rear shellbearing. Apply an even coat of lubricant tothe shaft. DO NOT lubricate the hex end.(See Figure 127.)
Figure 127
Note: When lubricating parts, use anapproved food grade lubricant (example:Taylor Lube HP).
64
Note: To ensure the mix does not leak out ofthe back of the freezing cylinder, the middlesection of the boot seal should be convex orextend out from the seal. If the middle sectionof the boot seal is concave or extending intothe middle of the seal, turn the seal inside out.(See Figure 128.)
Figure 128
2. Insert the beater drive shaft through therear shell bearing in the freezing cylinderand engage the hex end firmly into thedrive coupling. (See Figure 129.)
Figure 129
USE EXTREME CAUTION whenhandling the beater assembly. The scraperblades are very sharp and may cause injury.
3. Before installing the beater assembly,check the scraper blades for any nicks orsigns of wear. If any nicks are present, orif the blades are worn, replace bothblades.
If the blades are in good condition, installthe scraper blade clips over the scraperblades. Place the rear scraper blade overthe rear holding pin on the beater.(See Figure 130.)
Figure 130
Note: Soft serve side scraper blades shouldbe replaced every 3 months.
Note: The hole on the scraper blade must fitsecurely over the pin to prevent costlydamage.
4. Holding the rear blade on the beater, slideit into the freezing cylinder halfway. Installthe front scraper blade over the frontholding pin. (See Figure 131.)
Figure 131
65
5. Install the beater shoes. (See Figure 132.)
Figure 132
6. Slide the beater assembly the rest of theway into the freezing cylinder.
Make sure the beater assembly is inposition over the drive shaft by turning thebeater slightly until the beater is properlyseated. When in position, the beater willnot protrude beyond the front of thefreezing cylinder. (See Figure 133.)
Figure 133
7. Assemble the draw valve. Slide the 3o-rings into the grooves on the draw valveand lubricate. (See Figure 134.)
Figure 134
8. Lightly lubricate inside of the top of thefreezer door valve cavity.(See Figure 135.)
Figure 135
Insert the draw valve from the top, withthe draw handle slot facing forward.(See Figure 136.)
Figure 136
9. Assemble the freezer door. Place the doorgasket into the groove on the back of thefreezer door. Slide the front bearing overthe baffle rod so the flanged edge isagainst the door. DO NOT lubricate thegasket or bearing. (See Figure 137.)
Figure 137
66
10. Install the freezer door. Insert the bafflerod through the beater in the freezingcylinder. With the door seated on thefreezer studs, install the handscrews.Tighten equally in a criss-cross pattern toinsure the door is snug. (See Figure 138.)
Figure 138
11. Install the draw handle. Slide the fork ofthe draw handle in the slot of the drawvalve. Secure with pivot pin.(See Figure 139.)
Figure 139
Note: The soft serve side features an ad-justable draw handle to provide portioncontrol, giving a better consistent quality toyour product and controlling costs. The drawhandle should be adjusted to provide a flowrate of 5 to 7-1/2 oz. (142 g. to 213 g.) of prod-uct by weight per 10 seconds. To INCREASEthe flow rate, turn the adjustment screwCLOCKWISE. Turn the adjustment screwCOUNTER-CLOCKWISE to DECREASE theflow rate.
12. Slide the long drip pan into the hole in thefront panel above the syrup toppingdispensers. (See Figure 140.)
Figure 140
13. Slide the two shorter drip pans into theholes in the rear panel. Slide the twonotched drip pans into the left and rightside panels. (See Figure 141.)
Figure 141
14. Install the front drip tray and splash shieldunder the door spouts. (See Figure 142.)
Figure 142
67
Mix Pump Assembly
1. Inspect the rubber pump parts. O-ringsand gasket must be in 100% goodcondition for the pump and entire machineto operate properly. The o-rings andgasket cannot properly serve theirintended function if nicks, cuts, or holes inthe material are present.
Replace any defective parts immediatelyand discard the old.
2. Assemble the piston. Slide the red o-ringinto the groove of the piston. DO NOTlubricate the o-ring. (See Figure 143.)
Figure 143
3. Apply a thin layer of lubricant to the insideof the pump cylinder at the retaining pinhole end. (See Figure 144.)
Figure 144
4. Insert the piston into the retaining pin holeend of the pump cylinder.(See Figure 145.)
Figure 145
5. Assemble the valve cap. Slide the redo-ring into the groove of the valve cap.DO NOT lubricate the o-ring.(See Figure 146.)
Figure 146
6. Slide the pump valve gasket into theholes on the cap. DO NOT lubricate thegasket. (See Figure 147.)
Figure 147
68 120312
7. Insert the valve cap into the hole in themix inlet adapter. (See Figure 148.)
Figure 148
8. Insert the mix inlet assembly into thepump cylinder. (See Figure 149.)
Figure 149
The adapter must be positioned into thenotch located at the end of the pumpcylinder.
9. Secure the pump parts in position bysliding the retaining pin through the crossholes located at one end of the pumpcylinder. (See Figure 150.)
Figure 150
Note: The head of the retaining pinshould be located at the top of the pumpwhen installed.
10. Assemble the feed tube assembly. Slidethe check ring into the groove of the feedtube. (See Figure 151.)
Figure 151
11. Install one red o-ring on each end of themix feed tube, and thoroughly lubricate.(See Figure 152.)
Figure 152
12. Lay the pump assembly, pump clip, cotterpin and agitator in the bottom of the mixhopper for sanitizing. (See Figure 153.)
Figure 153
69
13. Slide the large black o-ring and the twosmaller black o-rings into the grooves onthe drive shaft. Thoroughly lubricate theo-rings and shaft. DO NOT lubricate thehex end of the shaft. (See Figure 154.)
Figure 154
14. Install the hex end of the drive shaft intothe drive hub at the rear wall of the mixhopper. (See Figure 155.)
Figure 155
Note: For ease in installing the pump,position the ball crank of the drive shaft in the3 o'clock position.
Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
2. Install syrup hole plugs in the syrup portsin the freezer door. (See Figure 156.)
Figure 156
3. Pour the sanitizing solution over all partsin the bottom of the mix hopper and allowit to flow into the freezing cylinder.
Note: You have just sanitized the mixhopper and parts; therefore, be sure yourhands are clean and sanitized before goingon in these instructions.4. Prepare four more gallons (15.2 liters) of
5. Install the air/mix pump assembly at therear of the mix hopper. To position thepump on the drive hub, align the drive slotin the piston with the drive crank of thedrive shaft. Secure the pump in place byslipping the pump clip over the collar ofthe pump, making sure the clip fits into thegrooves in the collar. (See Figure 157.)
Figure 157
70 080723
6. CAUTION!Install the pump end of the mix feedtube and secure with the cotter pin.Failure to follow this instruction couldresult in sanitizer spraying on theoperator.
7. Using the white hopper brush, clean themix level sensing probes, the mix hopper,mix inlet hole, the outside of the agitatordrive shaft housing, the agitator, theair/mix pump, pump clip, mix feed tubeand cotter pin.
8. Pour the four gallons (15.2 liters) ofsanitizing solution into the mix hopper.The sanitizing solution should be within 1”(2.5 cm.) of the top of the hopper.
9. Using the white hopper brush, scrub theexposed sides of the hopper. Wait at leastfive minutes before proceeding with theseinstructions.
10. Place the power switch in the ON position.
11. Touch the WASH symbol . This willcause the sanitizing solution in thefreezing cylinder to come in contact withall areas of the freezing cylinder.(See Figure 158.)
Figure 158
12. With a pail beneath the door spout, openand close the draw valve six times.
13. Touch the PUMP symbol to sanitizethe inside of the air/mix pump and the mixfeed tube.
14. Open the draw valve and draw off all theremaining sanitizing solution.
15. Touch the WASH and PUMPsymbols to stop the WASH andPUMP modes and to close the drawvalve. (See Figure 159.)
Figure 159
Note: Be sure your hands are clean andsanitized before going on in theseinstructions.
16. Place the agitator on the agitator driveshaft housing. (See Figure 160.)
Figure 160
Note: If the agitator paddle should stopturning during normal operation, withsanitized hands, remove the agitator from theagitator drive shaft housing and brush cleanwith sanitizing solution. Install the agitatorback onto the agitator drive shaft housing.
71
17. Remove the cotter pin from the pump.Stand the mix feed tube in the corner ofthe mix hopper. Place the cotter pin inposition in the outlet fitting of the pump.(See Figure 161.)
Figure 161
18. Remove the restrictor cap and the syruphole plugs.
19. Return to the freezer with a small amountof sanitizing solution. With a pail belowthe door spout, dip the door spout brushinto the sanitizing solution and brushclean the syrup ports in the freezer door,door spout, bottom of the driven spinnerand spinner blade, and syrup line fittings.
Note: To assure sanitary conditions aremaintained, brush clean each item for a totalof 60 seconds, repeatedly dipping the brush insanitizing solution.
20. With the syrup port brush, brush eachsyrup port hole 10 to 15 times. Dip thebrush in sanitizing solution beforebrushing each port.
21. Fill the squeeze bottle with sanitizingsolution. With a pail beneath the door,insert the tube end of the squeeze bottleinto the syrup port, and squeeze the bottlefirmly. This action will force solution out ofthe adjacent port and down around thespinner. This procedure should beperformed for at least 10 seconds perport.
22. Install the syrup valves and the restrictorcap.
Sanitizing - Soft Serve Side
1. Prepare 2.5 gallons (9.5 liters) of KAY-5®Sanitizer (HCS) solution. Use one packetin 2.5 gallons (9.5 liters) of water (100PPM).
2. Pour the sanitizing solution over all partsin the bottom of the mix hopper and allowit to flow into the freezing cylinder.
Note: You have just sanitized the mixhopper and parts; therefore, be sure yourhands are clean and sanitized before goingon in these instructions.
While the solution is flowing into thefreezing cylinder, take particular care tobrush clean the mix level sensing probes,the mix hopper, mix inlet hole, the outsideof the agitator housing, the agitator, theair/mix pump, pump clip, mix feed tubeand cotter pin.
3. Install the pump assembly at the rear ofthe mix hopper. To position the pump onthe drive hub, align the drive hole in thepiston with the drive crank of the driveshaft. Secure the pump in place byslipping the pump clip over the collar ofthe pump, making sure the clip fits into thegrooves in the collar. (See Figure 162.)
Figure 162
4. CAUTION!Install the pump end of the mix feedtube and secure with the cotter pin.Failure to follow this instruction couldresult in sanitizer spraying on theoperator.
6. Pour the sanitizing solution into the mixhopper.
7. Brush the exposed sides of the hopper.Wait at least 5 minutes before proceedingwith these instructions.
8. Touch the WASH symbol . This willcause the sanitizing solution in thefreezing cylinder to be agitated.
9. With a pail beneath the door spout, openthe draw valve and touch the PUMPsymbol . Open and close the drawvalve 6 times. Open the draw valve anddraw off the sanitizing solution.
10. Touch the WASH and PUMP symbolsand close the draw valve.
(See Figure 163.)
Figure 163
Note: Be sure your hands are clean andsanitized before going on in theseinstructions.
11. Place the agitator on the agitator driveshaft housing. (See Figure 164.)
Figure 164
Note: If agitator should stop turning duringnormal operation, with sanitized hands,remove agitator from agitator drive shafthousing and brush clean with sanitizingsolution. Install the agitator back onto theagitator drive shaft housing.
12. Remove the cotter pin from the pump.Stand the mix feed tube in the corner ofthe mix hopper. Place the cotter pin inposition in the outlet fitting of the pump.(See Figure 165.)
Figure 165
Note: You have just sanitized all foodcontact surfaces of the freezer.
73 111205
Priming - Shake Side
Note: Use only FRESH MIX when priming thefreezer.
1. With a mix pail beneath the door spout,touch any FLAVOR SELECT symbol toopen the draw valve. Pour 2-1/2 gallons(9.5 liters) of FRESH mix into the mixhopper and allow it to flow into thefreezing cylinder. This will force out anyremaining sanitizing solution. When fullstrength mix is flowing from the doorspout, touch any FLAVOR SELECTsymbol to close the draw valve.
2. When mix stops bubbling down into thefreezing cylinder, remove the cotter pinfrom the outlet fitting of the mix pump.Insert the outlet end of the mix feed tubeinto the mix inlet hole in the mix hopper.Place the inlet end of the mix feed tubeinto the outlet fitting of the mix pump.Secure with cotter pin. (See Figure 166.)
Figure 166
3. Install the shake cup holder.(See Figure 167.)
Figure 167
4. Select the AUTO symbol .
5. Fill the hopper with fresh mix and placethe mix hopper cover in position.
Priming - Soft Serve SideNote: Use only FRESH MIX when priming thefreezer.1. With a mix pail beneath the door spout,
open the draw valve. Pour 2-1/2 gallons(9.5 liters) of FRESH mix into the mixhopper and allow it to flow into thefreezing cylinder. This will force out anyremaining sanitizing solution. When fullstrength mix is flowing from the doorspout, close the draw valve.
2. When mix stops bubbling down into thefreezing cylinder, remove the cotter pinfrom the outlet fitting of the mix pump.Insert the outlet end of the mix feed tubeinto the mix inlet hole in the mix hopper.Place the inlet end of the mix feed tubeinto the outlet fitting of the mix pump.Secure with cotter pin.
3. Select the AUTO symbol .
Note: This procedure should be done 15minutes before product is expected to beserved.4. Fill the hopper with fresh mix and place
the mix hopper cover in position.
74 130927
VFD SCREENS
The vacuum fluorescent display (VFD) locatedin the center of the control panel is normallyblank during the daily operation of themachine. The display is activated when theCALIBRATE symbol or the Manager'sMenu is selected. The display screen will alsoalert the operator of specific faults detected bythe control.
Power Up
When the machine is powered, the controlsystem will initialize to perform a systemcheck. There will four types of data that thesystem will check when the control isinitializing: Lamp Test, Lockout Data,Configuration Data, and System Data.(See Figure 168.)
C602 / C606 UVC4V01.05.XXXlamptest
Figure 168
Lamp Test: The control and software versionis displayed and all of the LED's on the displaypanel are illuminated. (See Figure 169.)
Initializing . . . . .
Figure 169
Following the lamp test, three separatescreens will appear during initialization.
Initializing . . . . Lockout DataInitializing . . . . Config DataInitializing . . . . System Data
During the INITIALIZING . . . . . if the systemdetects corrupt data, the following display willalert the operator that the control settingshave changed. (See Figure 170.)
SERVICE REQ'DNVRAM FAULTRESET TO DEFAULTS< Press to clear
Figure 170
Once the system has initialized, the number ofdays remaining before the next required brushcleaning is indicated on the control panel andthe SAFETY TIMEOUT screen is displayedwith the alarm turned on. (See Figure 171.)
SAFETY TIMEOUTANY KEY ABORTS
Figure 171
The SAFETY TIMEOUT screen will bedisplayed, with the alarm on, for 60 seconds oruntil any control symbol is selected.
After the safety timeout has been completedand the power switch is OFF, the statusscreen will display. When the brush cleanrequirements have been met, the followingscreen will display. (See Figure 172.)
If a brush cleaning was not completed, thestatus screen will display the current hoppertemperature, barrel temperature, and the fiveminute brush clean timer. (See Figure 173.)
POWER SWITCH OFFTIME: 5:00
41.0 HOPPER 41.041.0 BARREL 41.0
Figure 173
75
Power Switch ON
When the power switch is placed in the ONposition, the control panel touch keys becomeoperative. The VFD will be either blank orindicate that the unit has been cleaned.(See Figure 174.)
UNIT CLEANED
Figure 174
Display for International Models Only:
Some International models will continuouslydisplay the temperature of each mix hopperwhen the power switch is in the ON position.(See Figure 175.)
HOPPER 21.0 21.1
UNIT CLEANED
Figure 175
Heat Cycle
The HEAT symbols on the control panelare illuminated throughout the heat treatmentcycle. Two warning messages will bedisplayed on the screen. “DO NOT DRAW” willbe displayed when the mix temperature isbelow 130_F (54.4_C). (See Figure 176.)
L: DO NOT DRAWR: DO NOT DRAW
Figure 176
When the temperature of the mix is above130_F (54.4_C) the screen will display amessage indicating that HOT PRODUCT is inthe machine. (See Figure 177.)
L: HOT PRODUCTR: HOT PRODUCT
Figure 177
DO NOT attempt to draw product ordisassemble the unit during the HEAT cycle.The product is hot and under extremepressure.
In the HEAT cycle, the mix temperature in thehoppers and freezing cylinders must be raisedto 151_F (66.1_C) within 90 minutes.
When the heating phase is complete, thefreezer goes into the holding phase of thecycle. The holding phase will keep the temper-ature above 151_F (66.1_C) for a minimum of30 minutes.
The final phase of the heat treatment cycle isthe cooling phase. The freezer must cool themix below 41_F (5_C) within two hours.
When the entire heat cycle has beencompleted, the HEAT symbols will nolonger be illuminated. The machine will enterthe STANDBY mode (STANDBY symbolsand illuminate). The machine can be placedin AUTO or left in STANDBY.
Heat Cycle Failure MessagesTo comply with health codes, heat treatmentsystem freezers must complete a heattreatment cycle daily, and must bedisassembled and brush cleaned a minimumof every 14 days. Brush cleaning is the normaldisassembly and cleaning procedure found inthis manual. Failure to follow these guidelineswill cause the control to lock the freezer out ofthe AUTO mode.
Always comply with local guidelines for themaximum number of days allowed betweenbrush clean cycles. (See the Manager's Menufor setting the Brush Clean interval, onpage 84.)
76
If the Heat Treatment Cycle fails, the VFD willdisplay a failure message and return thefreezer to the STANDBY mode. A “lock” isdefined as a special STANDBY mode ofoperation which does not allow the machine tooperate in the AUTO mode.There are two types of freezer lock conditionsthat can occur: Hard Lock or Soft Lock. A HardLock requires the machine be disassembledand brush cleaned. A Soft Lock can becorrected by either disassembling and brushcleaning the machine, or by starting anotherheat treatment cycle.Hard Lock: There are two causes of a hardlock failure:1. The brush clean timer has elapsed
(maximum setting of 14 days).(See Figure 178.)
BRUSH CLEAN TIMEOUTFREEZER LOCKEDCLEANING REQ'DWASH TO BRUSH CLEAN
Figure 178
Selecting the WASH symbol willdisplay the following screen.(See Figure 179.)
FREEZER LOCKED
Figure 179
2. There has been a thermistor failure(freezing cylinder, hopper, or glycol)during the heat treatment process.(See Figure 180.)
SYSTEM FAULTFREEZER LOCKEDSERVICE REQ'D
< PRESS TO CLEAR
Figure 180
Selecting the CALIBRATE symbol willindicate which thermistor caused the HardLock. (See Figure 181.)
L: HOPPER THERM BAD
FREEZER LOCKED
Figure 181
If the machine has hard locked and an attemptis made to enter AUTO, the machine will enterthe STANDBY mode and display the followingmessage. (See Figure 182.)
FREEZER LOCKED
Figure 182
To restore the message that identified thereason for the hard lock, turn the power switchOFF for five seconds and then return thepower switch to the ON position. The originalmessage with the reason for the Hard Lockwill be displayed. The FAULT DESCRIPTIONcan also be found in the Manager's Menu(See page 85.)
The FREEZER LOCKED message will remainon the display until the brush cleanrequirements are fulfilled. The freezer must bedisassembled in order to activate the fiveminute timer on the display screen. Once thetimer counts down to zero, the lockout iscleared.
77
Soft Lock: If a heat treatment cycle has notbeen initiated within the last 24 hours, a softlock failure will occur. A soft lock allows theoperator to correct the cause of the soft lock.The operator has the option of either startinganother heat cycle or brush cleaning themachine.
When a soft lock occurs, the machine will gointo the STANDBY mode. The followingmessage is displayed on the screen. Thereason for the soft lock is indicated on thesecond line. (See Figure 183.)
HEAT TREAT FAILUREREASONHEAT FOR HEAT CYCLEWASH TO BRUSH CLEAN
Figure 183
If the reason for the soft lock has beencorrected, selecting the HEAT symbolinitiates a Heat Cycle immediately. Selectingthe WASH symbol when the abovemessage is displayed will hard lock themachine and brush cleaning will be necessary.
Following are the variable messages for softlock failures that appear on the second line ofthe screen.
POWER SWITCH OFF Power switch was in theOFF position.
MIX OUT PRESENT There was a mix outcondition present.
AUTO OR STANDBYOFF
The machine was not inthe AUTO or STANDBYmode.
NO HEAT CYCLETRIED
A heat treatment cyclewas not attempted inthe last 24 hours.(AUTO HEAT TIMEwas advanced,a powerloss was experienced atthe time the cycle wasto occur, or a heat cyclefailure not due to athermistor failure.)
If the following screen appears, a soft lock hasoccurred during the heat treatment cycle.(See Figure 184.)
HEAT TREAT FAILUREFREEZER LOCKEDHEAT FOR HEAT CYCLEWASH TO BRUSH CLEAN
Figure 184
A soft lock can also occur any time duringoperation when the hopper or freezing cylindertemperature rises above 59_F (15_C), risesand remains above 45_F(7_C) for more thanone hour, or rises and remains above41_F(5_C) for more than four hours. If aPRODUCT OVER TEMPERATURE conditionoccurs during operation, the following screenwill appear. (See Figure 185.)
PRODUCT OVER TEMP
HEAT FOR HEAT CYCLEWASH TO BRUSH CLEAN
Figure 185
When one of these messages appears,automatic freezer operation cannot take placeuntil the freezer is disassembled and brushcleaned, or has completed a heat treatmentcycle. Select the HEAT symbol to start aheat cycle, or select the WASH symbol todisassemble and brush clean the machine.
Once the freezer is unlocked by starting aheat treatment cycle the HEAT symbol willilluminate and the following message will bedisplayed on the screen. (See Figure 186.)
L: DO NOT DRAWR: DO NOT DRAW
Figure 186
78 070423
If the WASH symbol is selected to clear thelockout by brush cleaning the machine, theFREEZER LOCKED message will remain onthe display until the brush clean requirementsare fulfilled. The freezer must bedisassembled in order to activate the fiveminute timer on the display screen. Once thetimer counts down to zero, the lockout iscleared. (See Figure 187.)
FREEZER LOCKED
Figure 187
To restore the message that identified thereason for the soft lock, turn the power switchOFF for five seconds, and then return thepower switch to the ON position. The originalmessage with the reason for the soft lock willbe displayed. (See Figure 188.)
HEAT TREAT FAILUREREASONHEAT FOR HEAT CYCLEWASH TO BRUSH CLEAN
Figure 188
The FAULT DESCRIPTION can also be foundin the Manager's Menu. (See page 85.)
Note: A record of Heat Cycle Data and LockOut History can be found in the Manager'sMenu. (See page 87.)
MANAGER'S MENU
The Manager's Menu is used to enter theoperator function displays. To access theMenu, touch the center of the CONE symbol
on the control panel. (See Figure 189.)
Figure 189
The shake AUTO symbol , the OPTIONALFLAVOR symbol and the CONE symbolwill be lit when the ACCESS CODE screen isdisplayed.
In the Menu program, the shake side AUTOsymbol , OPTIONAL FLAVOR symbol ,and CALIBRATION symbol will function asmenu keys.
AUTO - increases the value above thecursor and used to scroll upward in textdisplays
OPTIONAL FLAVOR - decreases thevalue above the cursor and used to scrolldownward in text displays.
CALIBRATION - advances the cursorposition to the right and is used to select menuoptions.
79 120308
Note: You will not be able to dispense shakeswhile accessing the Manager's Menu options,except when the CURRENT CONDITIONSscreen is displayed.
The soft serve side will continue operation inthe mode it was in when the Menu wasselected. However, the soft serve side controlkeys will not be lit and are non-functional whenthe Manager's Menu or Calibration Menu isdisplayed.
The control keys for both sides are functionalin the Manager's Menu when the CURRENTCONDITIONS screen is displayed. (SeeCURRENT CONDITIONS on page 91.)
Entering Access Code
With the ACCESS CODE screen on thedisplay use the AUTO or OPTIONALFLAVOR symbols to set the first codenumber in the cursor position. When thecorrect number is selected, touch theCALIBRATION symbol to move the cursorto the next number position. (See Figure 190.)
The access code for the Manager Menu is8309.
ENTER ACCESS CODE8 3 0 9_
Figure 190
Continue to enter the proper access codenumbers until all four numbers are displayed,then touch the CALIBRATION symbol . TheManager's menu list will display on the screenprovided the correct access code is entered.
If an incorrect number is entered for theaccess code, the display will exit the Menuprogram when the CALIBRATION symbolis selected. (See Figure 191.)
Figure 191
Menu Options
Touch the AUTO symbol or OPTIONALFLAVOR symbol to move up or downthrough the Menu. Select a Menu option byaligning the option with the arrow on the leftside of the screen, then touch theCALIBRATION symbol . Exit the Menuprogram by selecting EXIT FROM MENU ortouch the CONE symbol .
The following menu options are listed in theManager's Menu.
EXIT FROM MENU
SYRUP CALIBRATION
VERIFY CALIBRATION
SERVINGS COUNTER
SET CLOCK
AUTO HEAT TIME
AUTO START TIME
STANDBY MODE
BRUSH CLEAN CYCLE
MIX LEVEL AUDIBLE
FAULT DESCRIPTION
FAULT HISTORY
LOCKOUT HISTORY
HEAT CYCLE SUMMARY
HEAT CYCLE DATA
SYSTEM INFORMATION
CURRENT CONDITIONS
NET SERVICE PIN
80 120308
The EXIT FROM MENU option will exit theManager's Menu and return the control panelsymbols to normal operation.
The SYRUP CALIBRATION option allows themanager to access the calibration screenselections from the Manager's Menu. Thesame functions found in the Calibration menuare displayed on the screen when this menuoption is selected. (See “SYRUP SYSTEM” onpage 38.)
UNFLAVORED DRAWSYRUP CALIBRATIONSYRUP PRIME
> EXIT
Figure 192
Note: The Unflavored Draw Option will onlyappear on the screen when the shake side isin the AUTO mode.
The VERIFY CALIBRATION option is used toverify the amount of syrup dispensed is withinthe proper specification. (See Figure 193.)
VERIFY CALIBRATIONSelect a flavor
<- Press to clear
Figure 193
Remove the syrup valve from the dispensingdoor. With the line fully primed with syrup,position the syrup valve over the smallchamber side of the divided syrup cup, thenselect the corresponding flavor selection.Syrup will flow into the cup for 5 seconds (7seconds for Triple Thick Shake Syrup) andthen automatically stop flowing. Place the cupon a flat surface and check the amount ofsyrup dispensed. If the level is not within thecorrect specification, the flavor will need to berecalibrated. (See “Syrup Calibration” onpage 38.)
It is recommended to verify the calibration ofeach syrup flavor and note any flavors thatneed to be recalibrated before exiting theManager's Menu to access the CALIBRATIONMenu.
Select the CALIBRATION symbol to exitthe VERIFY CALIBRATION screen and returnto the Manager's Menu list.
The SERVINGS COUNTER screen is used tocheck or reset the number of servingsdispensed from the machine.(See Figure 194.)
SERVINGS COUNTERL = 0 R = 0Next
> Exit
Figure 194
Reset the SERVINGS COUNTER by selectingthe AUTO symbol to move the arrow to“Next”. The Reset Counters and Detailsselections will be displayed on the nextscreen. (See Figure 195.)
SERVINGS COUNTERDetails
> Reset CountersExit
Figure 195
Select the AUTO symbol to move the arrowto RESET COUNTERS. Then select theCALIBRATION symbol . (See Figure 196.)
SERVINGS COUNTERSAre you sure?
> YesNo
Figure 196
The display will ask, “Are you sure?” To resetthe counters, select the AUTO symbol tomove the arrow to YES. Select theCALIBRATION symbol to clear the left andright counters and return to the SERVINGSCOUNTER screen. If you do not want to clearthe serving counter, move the arrow to “No”and select the CALIBRATION symbol toreturn to the SERVINGS COUNTER screenwithout resetting the counters to zero.
81 120308
Note: The SERVINGS COUNTER willautomatically reset to zero when the machineis brush cleaned. (See Figure 197.)
SERVINGS COUNTERL = 0 R = 0Next
> Exit
Figure 197
Access the Details screen by selecting “Next”in the SERVINGS COUNTER screen. Movethe arrow to “Details” and then select theCALIBRATION symbol . (See Figure 198.)
SERVINGS COUNTER> Details
Reset CountersExit
Figure 198
The counter menu will also display details forthe number of servings for each flavor(chocolate, strawberry, vanilla, option,unflavored, and soft serve), and count themethod that ended the draw for each flavor(pyroelectric sensor detection, manuallyselecting a flavor key, draw safety timeout,and other). (See Figure 199.)
Example:
CHOCOLATEPyro = 0 Oper = 0Time = 0 Other = 0
> Next
Figure 199
Pyro = Pyrosensor detected and triggered theend of the draw.
Time = The Draw Safety Time setting wasreached before the pyrosensor detection orbefore a flavor key was selected.
Oper = A flavor key was selected to terminatethe draw.
Other = Any draw termination that is not Pyro,Time, or Oper (example: power switch turnedoff while product is dispensing)
The SET CLOCK option allows the managerto adjust the control clock date and time. Thedate and time may only be changed after thefreezer has been manually cleaned but beforeit has been placed in the AUTO or STANDBYmode. The following message will bedisplayed if the SET CLOCK option is selectedwhen the machine is not in a brush cleanstate. (See Figure 200.)
SET CLOCK08:00 04/02/2012NO CHANGES ALLOWED> Press Any Key
Figure 200
To change the date or time, select the SETCLOCK option in the menu. Touch the AUTOsymbol to advance the arrow from “Exit” to“Change”. Touch the CALIBRATION symbol
to select the Change option.(See Figure 201.)
SET CLOCK08:00 04/02/2012
Change> Exit
Figure 201
Change the time by touching the AUTO orOPTIONAL FLAVOR symbol with thecursor under the hour position. Move thecursor to the minutes by selecting theCALIBRATION symbol . Once the correctminutes are entered, select the CALIBRATIONsymbol to advance the cursor to the month.(See Figure 202.)
SET CLOCK08:00 04/02/2012_ _> Exit
Figure 202
82 120321
Enter the correct month, day, and year. Thenselect the CALIBRATION symbol toadvance to the DAYLIGHT SAVING TIMEscreen. (See Figure 203.)
DAYLIGHT SAVING TIMEENABLED
> EnableDisable
Figure 203
To Disable the Daylight Saving Time feature,select the AUTO symbol to move the arrowto “Disable”. Touch the CALIBRATION symbol
to save the selection.
To enable the Daylight Saving Time feature,select the AUTO symbol to move the arrowto “Enable”. Touch the CALIBRATION symbol
to save the selection.
The Daylight Saving Time feature, whenenabled, will automatically adjust the controlclock for Daylight Saving Time. Change themonth and week for Daylight Savings Time byselecting the AUTO symbol to advance thearrow from “Exit” to “Change”. Touch theCALIBRATION symbol to select theChange option and move to the next screen.(See Figure 204.)
MAR SECOND SUNDAYNOV FIRST SUNDAY
Change> Exit
Figure 204
Use the arrow keys to scroll to the appropriatemonth. Touch the CALIBRATION symbol toaccept the selection. (See Figure 205.)
DST START MONTHJANFEB
> MAR
Figure 205
Once the appropriate month has beenentered, scroll to the appropriate week. Touchthe CALIBRATION symbol to accept theselection. (See Figure 206.)
DST START WEEKFIRST SUNDAY
> SECOND SUNDAYTHIRD SUNDAY
Figure 206
Note: Scroll down to see selections “FOURTHSUNDAY” and “LAST SUNDAY”.
Select the month that Daylight Saving Timewill end. Touch the CALIBRATION symbolto accept the selection. (See Figure 207.)
DST END MONTH> NOV
DECJAN
Figure 207
Select the appropriate week that DaylightSaving Time will end. Touch theCALIBRATION symbol to accept theselection. (See Figure 208.)
DST END WEEK> FIRST SUNDAY
SECOND SUNDAYTHIRD SUNDAY
Figure 208
Select the CALIBRATION symbol to exitthe screen and return to the Menu.
83
The AUTO HEAT TIME screen allows theManager to set the time of day in which theheat treatment cycle will start.(See Figure 209.)
AUTO HEAT TIME0 0 : 0 0
Change> Exit
Figure 209
Note: Do not advance the Auto Heat Timesetting except on the day the unit is brushcleaned. Increasing the time between heatcycles will cause the machine to soft lock if thestart of the cycle does not begin within 24hours from the start of the previous heattreatment cycle.
To set the AUTO HEAT TIME select the AUTOsymbol to move the arrow to Change. Thenselect the CALIBRATION symbol . Thescreen will display the time with the cursorunder the hour position. (See Figure 210.)
AUTO HEAT TIME0 0 : 0 0_ _
Figure 210
Select the AUTO symbol or the OPTIONALFLAVOR symbol to increase or decreasethe hour to the desired setting. Then move thecursor to the minutes position by selecting theCALIBRATION symbol . Adjust the settingfor minutes, then select the CALIBRATIONsymbol to save the setting and return to theAUTO HEAT TIME screen. Select theCALIBRATION symbol to exit the screenand return to the Menu.
The AUTO START TIME option allows theManager to set the time of day at which themachine automatically enters the AUTO modefrom the STANDBY mode. The machine mustbe in the STANDBY mode without a freezerlock condition in order to AUTO start at theprogrammable time. The AUTO START TIMEcan also be Disabled and require starting theAUTO mode manually. (See Figure 211.)
AUTO START TIMEDISABLEDEnable
> Disable
Figure 211
Enable the AUTO START TIME by selectingthe AUTO symbol to move the arrow up toEnable. Select the CALIBRATION symbolto advance to the next screen.(See Figure 212.)
AUTO START TIME0 0 : 0 0
Change> Exit
Figure 212
Program the AUTO START TIME by selectingthe AUTO symbol to move the arrow toChange. Select the CALIBRATION symbolto advance to the next screen.(See Figure 213.)
AUTO START TIME0 0 : 0 0_ _
Figure 213
Program the AUTO START TIME byincreasing (AUTO symbol ) or decreasing(OPTIONAL FLAVOR symbol ) the hoursetting above the cursor. Select theCALIBRATION symbol to advance thecursor and program the minutes setting.
Select the CALIBRATION symbol to returnto the previous screen with the new timesetting displayed. Select the CALIBRATION
84
symbol to exit the screen and return to theMenu.
The STANDBY MODE option is used only onmodels which have the control panel Standbykeys disabled.
The STANDBY option is used to manuallyplace the left or right side in the Standby modeduring long, no draw periods. Select theSTANDBY screen from the Menu. Select theAUTO symbol to move the arrow up to theleft (shake) or right (soft serve) side. Selectthe CALIBRATION symbol to activateStandby for the selected side.
Repeat the steps to activate Standby on theremaining side. (See Figure 214.)
STANDBY MODELEFTRIGHT
> Exit
Figure 214
Discontinue Standby operation for either sideby exiting the Manager's Menu and select theAUTO mode.
The BRUSH CLEAN CYCLE option allows theManager to select the maximum number ofdays between brush cleaning the machine.The brush clean cycle may only be changedafter the freezer has been manually cleanedbut before it has been placed in the AUTO orSTANDBY mode.
The following message will be displayed if theBRUSH CLEAN CYCLE option is selectedwhen the machine is not in a brush cleanstate. (See Figure 215.)
BRUSH CLEAN CYCLETIME 14 DAYSNO CHANGES ALLOWED
Press Any Key
Figure 215
Change the number of days between brushclean intervals by selecting the AUTO symbol
to decrease the days or the OPTIONALFLAVOR symbol to increase the number ofdays. Select the CALIBRATION symbol tosave the setting and exit back to the Menu.The number of days displayed on the brushclean counter will change to the new setting.(See Figure 216.)
BRUSH CLEAN CYCLETIME 14 DAYS
Figure 216
Always comply with local guidelines on thenumber of days allowed between brush cleancycles.
The MIX LEVEL AUDIBLE option, whenenabled, will alert the operator with an audibletone when there is mix low or mix outcondition. The following screen is displayedupon selecting this option. (See Figure 217.)
MIX LEVEL AUDIBLEENABLED
> EnableDisable
Figure 217
Disable the audible tone feature by selectingthe AUTO symbol to move the arrow toDISABLE. Select the CALIBRATION symbol
to save the new setting and return to theMenu. The control panel icons for Mix Lowand Mix Out will light as the mix level drops inthe hopper but the audible tone will bedisabled.
85 080918
The FAULT DESCRIPTION display willindicate if there is a fault with the freezer andthe side of freezer where the fault occurred.When no faults are detected the followingscreen will be displayed. (See Figure 218.)
FAULT DESCRIPTIONNO FAULT FOUND
Figure 218
Select the CALIBRATION symbol todisplay the next fault found or return to theMenu if no other faults exist. Selecting theCALIBRATION symbol any time faults aredisplayed will clear the faults if corrected, uponreturning to the Menu screen.
Listed below are the variable messages whichwill appear, along with an explanation for thecorrective action.
NO FAULT FOUND - There was no fault foundin the freezer. Nothing will appear on thescreen after this variable message appears.
BEATER OVERLOAD - Press the beater resetbutton firmly for the side of the freezer with thefault. (See page 32.)
HPCO COMPRESSOR - Place the powerswitch in the OFF position. Wait 5 minutes forthe machine to cool. Place the power switch inthe ON position and restart each side inAUTO.
HOPPER THERMISTOR BAD - Place thepower switch in the OFF position. Call yourTaylor authorized service technician.
HOPPER OVER TEMP - Place the powerswitch in the ON position and verify that theAUTO or STANDBY symbol is illuminated.
BARREL OVER TEMP - Place the powerswitch in the ON position and verify that theAUTO or STANDBY symbol is illuminated.
BARREL THERMISTOR BAD - Place thepower switch in the OFF position. Call yourTaylor authorized service technician.
GLYCOL THERMISTOR BAD - Place thepower switch in the OFF position. Call yourTaylor authorized service technician.
PRODUCT DOOR OFF - Place the powerswitch in the OFF position. Check for properinstallation of the dispensing door and that thehand screws are tight.
COMP ON TOO LONG - Compressor ranmore than 11 consecutive minutes without theproduct reaching set point temperature. Cleanthe condenser filter, replace the scraperblades and reprime the unit using fresh mix. Ifthe fault appears again, call your Taylorauthorized service technician.
The LOCKOUT HISTORY screen displays ahistory of the last 100 soft locks, hard locks,brush clean dates, or aborted heat cycles.Page numbers are indicated in the upper righthand corner. Page 1 always contains the mostrecent failure. (See Figure 219.)
LOCKOUT HISTORY 100/00/00 00:00
REASON> Exit
Figure 219
The second line of the screen displays thedate and time a failure occurs. The third lineindicates the reason for a failure, or willindicate if a successful brush cleaning hasoccurred. Some failures occur with multiplereasons. When this occurs, a page will begenerated for each reason.
Select the AUTO symbol or OPTIONALFLAVOR symbol to advance forward orbackward to view each screen.
86 130927
Listed below are the variable messages thatmay appear.
Faults Occurring Entering a Heat TreatmentCycle
POWER SWITCH OFF - The power switch isOFF.
AUTO OR STBY OFF - The control was not inAUTO or STANDBY.
MIX OUT FAILURE - A mix out condition waspresent.
NO HEAT CYCLE TRIED - The Auto HeatTime was set to attempt a heat cycle morethan 24 hours after the last successful heatcycle.
Faults Occurring While in Heat Mode
HEAT MODE FAILURE - The maximumallowable heat mode time exceeded 90minutes.
COOL MODE FAILURE - The maximumallowable cool mode time exceeded 120minutes.
HOLD PHASE RESTART - The temperaturefell below 150°F (65.6°C).
TOTAL TIME FAILURE - The maximumallowable total heat treatment time exceeded6 hours.
BRUSH CLEAN TIMEOUT - The total days inoperation exceeded the brush clean cyclesetting.
POWER SWITCH OFF - The power switchwas turned OFF during the heat cycle.
POWER FAIL IN H/C - A power failureoccurred during the heat treatment cycle.
(L/R) MIX LOW FAILURE - The mix level inthe (left/right) Hopper is too low for asuccessful heat cycle.
(L/R) BEATER OVLD H/C - The overloadtripped for the (left/right) side beater motor.
(L/R) BRL THERM FAIL - The thermistorsensor for the (left/right) side barrel failed.
(L/R) HOPPER THERM FAIL - The thermistorsensor for the (left/right) side hopper failed.
(L/R) HPCO H/C - The (left/right) side highpressure switch opened during the heattreatment cycle.
Faults Occurring While in AUTO Mode
(L/R) HPR>41F (5C) AFTER 4 HR - The mixtemperature in the left or right hopper wasabove 41_F (5_C) more than four hours.
(L/R) BRL>41F (5C) AFTER 4 HR - The mixtemperature in the left or right barrel wasabove 41_F (5_C) more than four hours.
(L/R) HPR>45F (7C) AFTER 1 HR - The mixtemperature in the left or right hopper wasabove 45_F (7_C) more than one hour.
(L/R) BRL>45F (7C) AFTER 1 HR - The mixtemperature in the left or right barrel wasabove 45_F (7_C) more than one hour.
(L/R) HPR>41F (5C) AFTER PF - The mixtemperature in the left or right hopper wasabove 41_F (5_C) more than four hoursfollowing a power failure.
(L/R) BRL>41F (5C) AFTER PF - The mixtemperature in the left or right barrel wasabove 41_F (5_C) more than four hoursfollowing a power failure.
(L/R) HPR>59F (15C) - The mix temperaturein the left or right hopper exceeded 59_F(15_C).
(L/R) BRL>59F (15C) - The mix temperaturein the left or right barrel exceeded 59_F(15_C).
The FAULT HISTORY screens will display upto 100 faults that have occurred. The mostrecent fault is displayed on screen 1. Thedate, time, and fault description is displayedon each screen. (See Figure 220.)
FAULT HISTORY 104/23/12 08:00
FAULT DESCRIPTION> Exit
Figure 220
Advance to the next most recent occurringfault by selecting the AUTO symbol . Scrollthe screens in the opposite direction byselecting the OPTIONAL FLAVOR symbol .
87 120308
Exit the FAULT HISTORY screen and returnto the menu by selecting the CALIBRATIONsymbol .
Fault Descriptions
(L/R) Comp On Too Long - The left or rightmain compressor has run for more than 11consecutive minutes without dispensingproduct.(L/R) Product Door Off - The left or rightfreezer door is not completely installed or thesafety interlock circuit has opened.(L/R) Hopper Therm Bad - The left or righthopper thermistor probe is SHORTED orOPEN.(L/R) Hopper Over Temp - The left or righthopper thermistor probe is reading over 200°F(93°C).(L/R) Barrel Over Temp - The left or rightbarrel thermistor probe is reading over 200°F(93°C).(L/R) Beater Overload - The left or right resetmechanism has tripped.(L/R) HPCO Compressor - The left or righthigh pressure switch contacts have opened.(L/R) Glycol Therm Bad - The left or rightglycol thermistor probe is reading over 200°F(93°C).
The HEAT CYCLE SUMMARY screendisplays the hours since the last heat cycle,the hours since the product temperature wasabove 150_F (65.6_C), and the number ofheat cycles completed since the last brushclean date. (See Figure 221.)
HEAT CYCLE SUMMARYHRS SINCE HC 0HRS SINCE 150.0 0HC SINCE BC 0
Figure 221
The HEAT CYCLE DATA screen contains arecord of up to 366 heat treatment cycles. Themost recent heat cycle data will be shown first.The Standard records have each heat cyclerecorded in three screens. Select the AUTOsymbol to move the arrow to “Standardrecords“ and select the CALIBRATION symbol
. (See Figure 222.)
HEAT TREAT CYCLE> Standard records
DetailsExit
Figure 222
The first screen displays the month and day ofthe heat cycle, the start time and end time,and the fault description. The bottom linedisplays the record number and indicates if apower failure occurred during the heat cycle(POWER FAILURE IN HC). (See Figure 223.)
HEAT TREAT CYCLE01/01 02:00 05:14NO FAULT FOUND
1
Figure 223
Select the AUTO symbol to advanceforward through the data pages. Select theOPTIONAL FLAVOR symbol to reverse thepage direction.
88 130927
Hopper and barrel temperature records foreach side of the freezer are displayed in thesecond and third screens. The second screenshows the left side (L) side of the freezer. (SeeFigure 224.) The third screen shows the rightside (R) of the freezer. (See Figure 225.)The top line of these screens shows thehopper (H) and barrel (B) temperaturesrecorded at the end of the Heat Treat Cycleand indicates the side (L or R) of the freezer.The remaining lines indicate the following:HEAT = Total time for the hopper (h) andbarrel (b) to reach 150.9°F (66.1°C).OVER = Total time the hopper (h) and barrel(b) temperature was above 150°F (65.6°C).COOL = Total time the hopper (h) and barrel(b) temperature was above 41°F (5°C) duringthe COOL phase.PEAK = Highest temperature reading for thehopper (h) and barrel (b) during the HeatTreatment Cycle.
H: 40.9 B:26.3 LHEAT OVER COOL PEAK1:12 0:49 h 1:19 161.00:46 1.11 b 0:15 169.7
Figure 224
H: 38.0 B:23.7 RHEAT OVER COOL PEAK1:09 0:52 h 1:11 161.20:66 1.00 b 0:15 169.9
Figure 225
The HEAT time indicates the amount of timetaken in each zone to reach 150.9°F (66.1°C).Each zone must remain above 150°F (65.6°C)for a minimum of 35 minutes. In addition, eachzone must be heated for a minimum of 115minutes.
Select the AUTO symbol to advance to thenext page or the OPTIONAL FLAVOR symbol
to view the previous page.A Heat Cycle Failure message will display onthe first screen if a failure occurred.
Listed below are variable failure codemessages which could appear on line 2.
HT HEAT TIME FAILUREMix temperature did not rise above151°F (66.1°C) in less than 90 minutes.
CL COOL MODE FAILUREMix temperature in the hopper andfreezing cylinder did not fall below 41°F(5°C) in less than 120 minutes.
TT TOTAL TIME FAILUREThe heat treatment cycle must be com-pleted in no more than 6 hours.
MO MIX OUT FAILUREA mix out condition was detected at thestart or during the heat cycle.
ML MIX LOW FAILUREThe Heat Phase or Cool Phase timewas exceeded and a mix low conditionwas present.
BO BEATER OLVD IN HCA beater overload occurred during theheat cycle.
HO HPCO IN HEAT CYCLEA high pressure cut-out condition oc-curred during the heat cycle.
PF POWER FAILURE IN HCA power failure caused the Heat Phase,Cool Phase, or Total Cycle Time toexceed the maximum allowed time. If apower failure occurs, but the heattreatment cycle does not fail, anasterisk(*) will appear on the third lineof the display.
PS POWER SWITCH OFFThe power switch was placed into theOFF position during the heat cycle.
TH THERMISTOR FAILUREA thermistor probe has failed.
OP OPERATOR INTERRUPTIndicates the heat cycle was aborted inthe OPERATOR INTERRUPT option inthe Service Menu.
PD PRODUCT DOOR OFFA product door is not in place or isloose.
89 120315
The HEAT CYCLE DATA Details record thetemperature in the freezing cylinders and mixhoppers every five minutes during the heattreatment cycle. Up to 366 heat treatmentcycles are recorded. The time and temperat-ure is displayed for the left hopper, left barrel,right hopper, and right barrel for each phaseduring the heat treat cycle. An individualphase or a complete heat treat cycle contain-ing all four phases can be viewed.
Heat Treatment Phases
HEAT The phase that heats the mix in thebarrels and hoppers to 151°F(6.1°C).
HOLD The phase that maintains the mixtemperature above 151°F (6.1°C)for a minimum of 30 consecutiveminutes.
SOAK The additional heating time thatmay follow the HOLD phase toinsure the total HEAT, HOLD, andSOAK time is not less than 115minutes.
COOL The phase that refrigerates the mixuntil all four temperature zones arecooled below 41°F (5°C).
In the HEAT CYCLE DATA screen, select theAUTO symbol to move the arrow up to“Details,” and then select the Calibrationsymbol . (See Figure 226.)
HEAT CYCLE DATAStandard records
> DetailsExit
Figure 226
The most recent heat treat cycle record(Recd 1) is displayed with the date and time.Access a different heat treatment cycle recordby selecting the OPTIONAL FLAVORsymbol to move the arrow to “Next record,”and select the Calibration symbol . Repeatthis step until the desired record with the dateand time is displayed. (See Figure 227.)
Recd 1 03/26 00:00> Display record
Next recordExit
Figure 227
With the arrow on the Display record line,select the Calibration symbol .(See Figure 228.)
HEAT TREAT CYCLE> HEAT phase temps
HOLD phase tempsSOAK phase temps
Figure 228
Select the OPTIONAL FLAVOR symbol toscroll down to the phase to be reviewed.Selecting “ALL phase temps” will display allfour phases of the heat treat cycle record insequential order. (See Figure 229.)
HEAT TREAT CYCLESOAK phase tempsCOOL phase temps
> ALL phase temps
Figure 229
The four temperature readings are recorded atthe same time on individual screens. Align thearrow with the phase to be reviewed andselect the Calibration symbol .(See Figures 230 and 231.)
HEAT TREAT CYCLE> HEAT phase temps
HOLD phase tempsSOAK phase temps
Figure 230
HEAT LH r 1 s 140.0 03/26 02:05
> Next zoneExit
Figure 231
90 120315
Line 1 Displays the Phase HEAT / HOLD /SOAK / COOL
LH Left Hopperr 1 Record Numbers 1 Sample Number
Line 2 Zone TemperatureDate & Time Temperature was recorded
Note: An L or an H displayed to the left of thetemperature reading indicates the temperaturewas the lowest or highest recorded during thephase.
Selecting the Calibration symbol willadvance the screen to the next zone. Thesecond temperature zone displayed is the leftbarrel (LB). (See Figure 232.)
HEAT LB r 1 s 125.4 03/26 02:05
> Next zoneExit
Figure 232
Select the Calibration symbol to advance tothe next temperature zone; the right hopper(RH). (See Figure 233.)
HEAT RH r 1 s 139.5 03/26 02:05
> Next zoneExit
Figure 233
Select the Calibration symbol to advance tothe last temperature zone in the recordedsample; the right barrel (RB).(See Figure 234.)
HEAT RB r 1 s 126.5 03/26 02:05
> Next sampleExit
Figure 234
Select the Calibration symbol again toadvance to the next sample. Each sample isdisplayed in 5 minute increments.(See Figure 235.)
HEAT LH r 1 s 246.4 03/26 02:10
> Next zoneExit
Figure 235
When the final sample in the phase isdisplayed, the Heat Cycle results screen canbe selected. (See Figure 236.)
HEAT RB r 1 s 14H 169.0 03/26
> ResultExit
Figure 236
If the COOL phase data or “All phase data”were reviewed, the final temperature zonesample in the record will be displayed with theselection for the result screen.(See Figure 237.)
COOL RB r 14 s 4220.0 03/26 05:15
> ResultExit
Figure 237
Select the Calibration symbol to view theHeat cycle results screen. (See Figure 238.)
PASS r 1 s43Heat Cycle results
> Next recordExit
Figure 238
91 120628
To view the details for the same phase in thepreceding record (“Next record”), select theCalibration symbol . If “All phase data” wasselected, the record number will remain thesame and the next phase sample will bedisplayed. (See Figure 239.)
HOLD LH r 1 s 16158.7 03/26 03:15
> Next zoneExit
Figure 239
Exit the record screens by moving the arrow to“Exit” and select the Calibration symbol .
The average heat treatment cycle will containapproximately 40 samples of the fourtemperature zone screens.
The SYSTEM INFORMATION is displayed onfour separate screens. The first screencontains the control and software versioninstalled in the machine. (See Figure 240.)
SOFTWARE VERSIONC602 / C606 UVCVERSION V01.04.000> Next
Figure 240
Select the CALIBRATION symbol toadvance to the next system information screencontaining the software language version.(See Figure 27.)
LANGUAGEV3.00English
> Next
Figure 241
For UVC4 models only, select theCALIBRATION symbol to advance to thethird system information screen containing theBoot loader version. (See Figure 242.)
Boot loaderV1.13.000
> Next
Figure 242
Select the CALIBRATION symbol toadvance to the last system information screencontaining the model bill of material andmachine serial number. (See Figure 243.)
B.O.M. C60000000S/N M0000000
> Next
Figure 243
Selecting the CALIBRATION symbol againwill return to the Menu list.
Note: In order to display the machine detailsin the system information screen, the modeland serial number information must have beenpreviously entered into the EDIT UNIT IDscreens in the Service Menu.
The CURRENT CONDITIONS screen providesthe product viscosity readings and the hopperand barrel temperatures. The left columndisplays the readings for the shake side andthe right column displays the readings for thesoft serve side. (See Figure 244.)
VISC 0 0.0HOPPER 38.0 38.0BARREL 25.0 18.0
Figure 244
CURRENT CONDITIONS is the only Menuscreen that will return the left and right sidecontrol panel keys to normal operation. TheMenu keys will not be lit when this option isselected so shakes can be dispensed and allpanel touch keys are fully functional. Use this
92 121219
screen when you wish to remain in theManager's Menu and dispense a shake.
Exit the CURRENT CONDITIONS screen andreturn to the Menu by selecting theCALIBRATION symbol .
The NET SERVICE PIN screen allows themanager to send a LON® service messageout the power line. This message facilitatesthe setup of the in-store network with smartenabled equipment. (See Figure 245.)
NET SERVICE PIN
Figure 245
Press the CALIBRATION symbol . Thefollowing screen appears. (See Figure 246.)
NEW SERVICE PINARE YOU SURE?YES
> NO
Figure 246
Press the AUTO symbol to move the cursorto “YES”. Press the CALIBRATION symbolto select it. The LON® service message hasnow been sent.
Note: A network commissioning process toolcalled the “wink” function can be initiated overthe existing user interface to identify a piece ofequipment. When the “wink” command isreceived through the network for the C602, theLEDs on the C602 front panel will illuminatefor 30 seconds.
Dispensing Shake Without Syrup
Beginning with software version 1.04, shakescan be dispensed without flavoring byselecting the left side pump symbol .(See Figure 247.)
Figure 247
The following screen will display.(See Figure 248.)
UNFLAVORED DRAW> YES
NO
Figure 248
Select the CALIBRATION symbol . The leftside PUMP symbol illuminates and unflavoredproduct immediately starts to dispense. Theunflavored draw ends and the PUMP lightextinguishes when the pyroelectric sensordetects the cup is full. The unflavored drawcan also be terminated by selecting the PUMPsymbol a second time.
Note: To cancel the UNFLAVORED DRAWscreen, touch the OPTIONAL FLAVORsymbol to move the arrow to “NO”, and selectthe CALIBRATION symbol .
Data LabelThe data label provides necessary informationthat the operator should record and refer towhen calling for parts or service. The datalabel is located on the rear or left side panel ofthe freezer.Complete for quick reference when thisinformation is requested.1. Model Number: C602-HT2. Serial Number3. Electrical Specs:
Voltage Cycle Phase4. Maximum Fuse Size: Amps5. Minimum Wire Ampacity: Amps6. Part Number:
Parts Warranty
Warranty is valid only if the parts areauthorized Taylor parts, purchased from anauthorized Taylor Distributor, and the requiredservice work is provided by a factoryauthorized service technician. Taylor reservesthe right to deny warranty claims onequipment or parts if non-approved parts orrefrigerant were installed in the machine,system modifications were performed beyondfactory recommendations, or it is determinedthat the failure was caused by neglect orabuse.
Note: Constant research results in steadyimprovements; therefore, information in thismanual is subject to change without notice.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on thismachine are warranted for the term indicatedon the warranty card accompanying thismachine. However, due to the MontrealProtocol and the U.S. Clean Air ActAmendments of 1990, many new refrigerantsare being tested and developed, thus seekingtheir way into the service industry. Some ofthese new refrigerants are being advertised asdrop-in replacements for numerousapplications. It should be noted that, in theevent of ordinary service to this machine'srefrigeration system, only the refrigerantspecified on the affixed data plate should beused. The unauthorized use of alternaterefrigerants will void your compressorwarranty. It will be the owner's responsibility tomake this fact known to any technician heemploys.It should also be noted, that Taylor does notwarrant the refrigerant used in its equipment.For example, if the refrigerant is lost during thecourse of ordinary service to this machine,
Taylor has no obligation to either supply orprovide its replacement either at billable orunbillable terms. Taylor does have theobligation to recommend a suitablereplacement if the original refrigerant isbanned, obsoleted, or no longer availableduring the five year warranty of thecompressor.
Taylor will continue to monitor the industry andtest new alternates as they are beingdeveloped. Should a new alternate prove,through our testing, that it would be acceptedas a drop-in replacement, then the abovedisclaimer would become null and void. Tofind out the current status of an alternaterefrigerant as it relates to your compressorwarranty, call the local Taylor Distributor or theTaylor Factory. Be prepared to provide theModel/Serial Number of the unit in question.