Sold separately H230-C26/26T HINGE 230-P4W-32T MOUNTING PLATE NSDX35(L/R)K SOFT DOWN STAY ※ 3 In case of IF-102S, (IF-H102S) lower guard plates are attached. AL-78 RAIL DR-19-B2 ROLLER SC-107-13 INSERT F-15 SLIDER GUARD PLATE( ※ 3 ) 230-C26/19T HINGE FOR YOUR SAFE WORK AND CORRECT INSTALLATION PARTS REQUIRED PER CABINET CABINET AND DOOR FABRICATION Caution : If not followed injury or damage may result. This is a part for furniture fittings. After installation, make sure to test the finished product thoroughly to ensure that it is well-functioning and safe. Do not try to use this product for anything other than its original purpose. Do not use the parts for applications that are out of specification. Make sure to follow the designated dimensions, specifications, and horizontal/vertical angles. Make sure that the cabinet is not warped, since it may affect the movement of the door. Recommended ambient temperature range is 0 ℃ - 40 ℃ . Make sure to check the screws for slack at regular intervals (one month from first usage, half a year and then one time every year is recommended). Affix attached caution sticker onto the door. SOFT CLOSING MECHANISM FOR INSET RECEDING DOOR : INSTALLATION INSTRUCTION DIMENSIONAL INFORMATION ※ 2 T=Door thickness (mm) IF-102S, IF-102W IF-H102S, IF-H102W 37.5 43.6 c 22.5 25 e 35 depth11 40 depth15 f 9.5+Door thickness 9.5+Door thickness d b = 3 b = 3 a=3 a=3 20 15 c d 41 41 DOOR DOOR WIDTH DOOR HEIGHT CABINET HEIGHT ( INSIDE ) DOOR WIDTH DOOR HEIGHT φ2 DEPTH 8 Bore on both inner side boards Bore to both inner side boards φ10 DEPTH 13 SECTION f e - ● The measurement provided in the table below is in case the door overhangs by 35 mm(A) from the edge of the top board when the door is fully inserted. 35 A B Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand for future reference. IF-102S(SINGLE-TYPE) IF-102W ( DOUBLE-TYPE ) IF-H102S ( SINGLE-TYPE ) IF-H102W ( DOUBLE-TYPE ) k 84 82 IF-102S, IF-102W IF-H102S, IF-H102W TYPE h 66.5 71.5 IF-102S, IF-102W IF-H102S, IF-H102W TYPE SUGATSUNE KOGYO CO.,LTD Tokyo, JAPAN Phone: +81 (0)3 3866 2260 E-mail:[email protected] SUGATSUNE KOGYO (UK) LTD Reading, UK Phone: +44 118 9272 955 E-mail:[email protected] SUGATSUNE EUROPE GmbH Dusseldorf, GERMANY Phone: +49 211 53812900 E-mail:[email protected] SUGATSUNE SHANGHAI Co., LTD Shanghai, CHINA Phone: +86 21 3632 1858 E-mail:[email protected] Guangzhou, CHINA Phone: +86 20 6639 3552 E-mail:[email protected] SUGATSUNE KOGYO INDIA PRIVATE LIMITED Mumbai, INDIA Phone: +91 22 28314490/91 E-mail:[email protected] SUGATSUNE AMERICA, INC California, USA Phone: +1 310 329 6373 E-mail:[email protected] Chicago, USA Phone: +1 312 461 1081 E-mail:[email protected]. SUGATSUNE CANADA, INC. Phone: +1 514 312 5267 E-mail:[email protected] 2019.12 1135-3 ABOUT THE PRODUCT SPECIFICATIONS TYPE IF-102S IF-102W IF - H102S IF - H102W DOOR WIDTH less than 1,200 mm DOOR THICKNESS(T) 15-20 mm 18-30 mm TORQUE MOMENTc 1.96-6.86N・m (20-70kgf・cm) 3.9-13.7N・m (40-140kgf・cm) 1.96-6.86N・m (20-70kgf・cm) 3.9-13.7N・m (40-140kgf・cm) IF-102S & IF-102W IF-H102S & IF - H102W B RECOMMENDED DOOR HEIGHT B RECOMMENDED DOOR HEIGHT AL-78-14 263.7 + T ※ 2 298.7 + T 260.9 + T 295.9 + T AL-78-16 314.5 + T 349.5 + T 311.7 + T 346.7 + T AL-78-19 390.7 + T 425.7 + T 387.9 + T 422.9 + T AL-78-24 517.7 + T 552.7 + T 514.9 + T 549.9 + T IF-102 IF - H102 IF-102S IF-102W IF - H102S IF - H102W ① 2 ② 1pair 14", 16",19" or 24" ③ 2 ④ 2 ⑤ 2 ⑥ 4 ⑦ 14 ⑧ 6 ⑨ 36 ⑩ 4 ⑪ 2 2 - - ⑫ - - 2 2 ⑬ 2 ⑭ 1 L×1, R × 1 1 L×1, R × 1 ① Bracket ② ③ ④ ⑤ ⑥ ⑦ Screw-A(M4 × 8) ⑧ Screw-B(M3.5 × 6) ⑨ Screw-C(3.5 ×16, Bind tapping) ⑩ Screw-D(3.5 × 16, oval tapping) ⑪ ⑫ ⑬ ⑭ ⑮ Caution sticker Prohibited Warning Caution Required Meaning of symbols INSTALLATION DRAWING (EXAMPLE) 1 Parts Assembly on Cabinet 4-1 Door Mounting 5 Door Adjustment 2 Bracket Installation 3 Parts Assembly on Door ・This product is a set of stays and hinges for an inset receding door. Do not force the door open beyond the hori- zontal position. It could damage the unit. Do not force the door to close faster when it is in closing motion. It could cause damage. Do not place any object on the door when it is opened. The object may fall. Do not place your hands anywhere near the mechanism to prevent injury. WARNING! ASSEMBLY TYPE Note: ※ 1 Door height × 1/2 × door weight. Cut the door so that there is a 3 mm gap between the cabinet and the door. (a & b gap). Drill 2 mm dia. and 8 mm depth holes inside of the cabinet. ① Bracket ⑭ Soft-down Stay NSDX35(L/R)K ⑬ Mounting plate ⑦ Screw M4×8 ② Rail ⑧ Screw M3.5×6 ⑦ Screw M4×8 22.5 32 k Arm fixing plate (Temporarily fix) Hinge h DOOR THICKNESS+12 Mount Position on Cabinet 4-2 Door Mounting Note: Use the hinge H230-C26/26T ⑫ only with IF-H102 ❷ Fasten arm of Soft-down stay. ❸ Mount guard plates. (To prevent stored articles from interfering with moving parts ※ 4 ) ※ 4 If the gaurd plates are not enough to avoid interference install a middle plate. Arm fixing screw Hinge Mounting plate ⑥ Guard plate(H) ❶ Assemble the hinges to the mounting plate. Arm fixing plate Hinge Mounting plate ❷ Fix arm of Soft-down stay. ※ 4 Mount guard plate(L) without stay. Mount guard plate(H) on the side with the stay. If the gaurd plates are not enough to avoid interference install a middle plate. ⑥ Guard plate(L) ❸ Mount guard plates. (To prevent stored articles from interfering with moving parts ※ 4 ) ❶ Assemble the hinges to the mounting plate. Vertical adjustment Turn clockwise to lower the door. Left-right adjustment Loosen the screws to adjust, then re-tighten. Closing speed adjustment screw Fix the plate after the door djustiment. When installing two stays, turn the two screws equally. Caution FASTER SLOWER Depth adjustment Loosen the screws to adjust, then re-tighten. Retinghten this screw by 2N ・ m ④ SC-107-13 + ③ DR-19-B2 ⑤ F-15, SLIDER INSERT ROLLER ② AL-78RAIL 14 12 28(1−7/64″) 348 (13−45/64″) 3 37 (1−29/64″) 34.1 (1−11/32″) 38 6 6 50 (1−31/32″) 35 3 3 435(17−1/8″) 7 78 (206) (8−7/64″) 369.5(14−35/64″) IN CASE OF 16" SLIDE(406.4 mm) 369.5(14−35/64″) 32 84 150(5−29/32″)