-
7. Level 2 Repair
7-1
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.Distribution, transmission,
or infringement of any content or data from this document without
Samsungs written authorization is strictly prohibited.
Remove the 2 screws.Check know where is Locking before removing
the Locking.In addition, prepare the Locking Remove Tool.
Remove along the indicated lines the Locking asshown in the
above figure. Remove the QRE01.
disassembly
1 2
3 4
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-2
Please lifted the QAN01 using the Lock Remove Toolas shown in
the above figure. Remove the QAN01.
Remove the 3 screws and 1 Connector. Remove the QRE15.
5 6
7 8
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-3
Remove the 8 screws. Check know where is Locking before removing
the Locking
Remove along the indicated lines the Locking asshown in the
above figure. Remove the QFR02.
9 10
11 12
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-4
Take care not to lose the QRF01, QCK02, QVK01,QMI01, QBC01.
Remove the QBR01 and then removing the 2 Connector.
Remove the QCA01.
Check electric shock point before removing the QCA07.- If you do
not have a discharger, be careful forelectric shock when removing
it.- If you have a discharger, It must be processed fordischarge to
the main condenser as shown in the abovepicture.
13 14
15 16ASSY-BARREL
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-5
Remove the 1 screw and 1 Connector. Remove the QCA07.
Remove the 2 Connector and QCB01(CBF COAXIALCABLE).Take care not
to damage the FPCB when removing TSPFPCB from the Connector.
Remove the QMP01.
17 18
19 20
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-6
Remove the 2 screws. Remove the QMI02, QSP01.Take care not to
lose the QMI02
Remove the 2 screws and 1 Connector, QCB01(CBF COAXIAL
CABLE).
Remove the QME02, QRF03.Take care not to lose the QRF03.
21 22
23 23
ASSY-SUB-RF PCB
ASSY-SPK
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-7
Remove the 2 QCB01. Pluck the using the tweezers the QBL05(PIN
BATTERY COVER)
Remove the QBL05, QBL07, QBL01.Take care not to lose the QBL07,
QBL05 Remove the using the Locking Remove Tool the 2 Locking.
24 25
26 27
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-8
Remove the QBL04 and then removing QBL06,QMO01. Take care not to
lose the QBL06.
The QFM01, QCA02, QME04 are remove in order of numberson the
QFR01.
29 30
ASSY-CAMERAVT CAM
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-9
The QME04, QCA02, QFM01 are assemble in order ofnumbers unto the
QFR01. Assemble the QBL06, QMO01 and then assemble QBL04.
Check the assembled of 2 LOCKING. Assemble the QBL05, QBL07,
QBL01.
1 2
3 4
Assembly
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-10
Insert the QCB01 in the groove.
Assemble the QRF03 on the QME02 and then assemble theQME02. When
assembling, assemble so that the bothendsside teminal of CBF
COAXIAL CABLE can come out to thequtside of the QME02.
Tightening the 2 screws and assemble the 1Connector, QCB01 (CBF
COAXIAL CABLE).
Assemble the QMI02 on the QSP01 and then assemble theQSP01. When
assembling, assemble so that the oneterminals of CBF COAXIAL CABLE
in remaining can come outto the outside of the QSP01.
5 6
7 8
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-11
Tightening the 2 screws.Assemble the QMP01. When assembling,
assemble so that theone terminals of CBF COAXIAL CABLE in remaining
can comeout to the outside of the QMP01.
Assemble the 2 Connector and QCB01(CBF COAXIALCABLE). Take care
not to damage the FPCB whenAssembling TSP FPCB from the
Connecotor
Assemble the QCA07.
9 10
11 12
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-12
Tightening the 1 screw and assemble 1 Connector. Assemble the
QCA01.
Assemble the 2 Connector and then attach the QBR01.-When place
the barrel be carful of FPCB crackaround the Barrel.
Assemble the QFR02, QRF01, QCK02, QVK01, QMI01, QBC01.-Please
check whether the components of the above pictureare altogether
assembled.
13 14
15 16
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-13
Assemble the QFR02. Please along the indicated lines the Locking
and assembleas shown in the above figure.
Tightening the 8 screws. Assemble the QRE15.
17 18
19 20
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-14
Tightening the 3 screws and then assemble 1Connector. Assemble
the QAN01.
Assemble the QRE01. Press along the indicated lines the Locking
and assembleas shown in the above figure.
21 22
23 24
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-15
Tightening the 2 screws.
25
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-16
Camera Adjustment
Adjustment List Must do CAMERA adjustment, when Main PCB or
Barrel ASSY is exchanged.
Section Sub SectionRepair Part
ETCMain PCB Lens Barrel
Adjustment #1 Color ShadingDefect Pixel Correction a sheet of
white paper
Adjustment #2(optinal) Color Shading
Only if a fifth picture has a purplecolor or black shadow on
4
corner,
Equipment List
Program Installation- 1. Adjustment Program Installation
1) Unzip GC_Adj_v3.2.2 SCV.zip file provided2) Open
GC_Adj_v3.2.2 SVC folder
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-17
3) Install vcredist_x86.exe file(Needed ONLY ONCE at the first
time)
Adjustment- 1. Set up for adjustment
1.1 How to connect it
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-18
1.2 Setup for Adjustment1) Check COM Port number of USB Serial
Port. (Control Panel Equipment Operator)
2) Execute shortcut file GCMot3.2.2_SCV in
adjustment_z4_zoom
3) Connect COM Port by click SET UP button
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-19
4) Re-run after closing program
If you changed USB cable port, you Should setup again.
5) Copy "c101_shading_data.bin" to SD card and insert it to the
product.6) Power off the product.7) Connect the product to Anyway
Jig with power off.
Do not connect the product power on to Anyway Jig.Connecting the
product to Anyway Jig make it turn on .
8) The product turn itself on.
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-20
This is set-up recommendation of Shading Adjustment. If you
don't have any tripod, you can hold theproduct by hand in front of
a sheet of white paper
1.3 Shading Adjustment1) Click the FILE button to open Script
file.
2) Select M_WriteDefaultTable.txt( PATH : adjustment_s4_zoom
> adj_script >M_WriteDefaultTable.txt )
3) Put a sheet of white paper in front of camera.
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-21
4) Click the START button to start adjustment.
5) Result of adjustment is displayed once.
(This process takes about 4 mins.)
6) Pull out SD memory card and check the picture data in.
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-22
( PATH : DCIM > Camera > SAM_xxxx.jpg)
7) Open the last picture among 5 pictures.(First picture would
be #1 and the last picture would
be #5.)
8) Check 4 corner on which there is purple color or black
shadow. If there is like NG image
below, go to "11)" or isn't, go to "9)
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-23
9) If the purple color or black shadow is not so serious like OK
images below, please close
factory mode by key strings.
10) Trun on telephone app and insert *#87976633#, then restart
the product. This is for changing
mode from factroy to user.
11) If there is purple color or black shadow on one of 4 corner
in the lase image, please checkthe other pictures and select best
image. (Please refer OK image above.)
12) Re-adjust the product with the best image data.13) Click the
FILE button to open Script file.
-
Level 2 Repair
Distribution, transmission, or infringement of any content or
data from this document without Samsungs written authorization is
strictly prohibited.
Confidential and proprietary-the contents in this service guide
subject to change without prior notice.
7-24
14) Select the script file of best image.(The best image number
is related with script name.)
=> If second picture is best, then select s_final_2.txt
15) Click the STARTbutton to start adjustment
16) Result of adjustment is displayed once.17) Restart the
product.