Sku.201734

1. Pictures of Product AccessoriesPower lines

Relay

Microphone

SOS alarm button

Instructions for quick installation and usePlease check whether accessories inside the box are complete, with the accessories subject to real objects.2. Technical parameters2.1 GSM frequency ranges: 850/900/1800/19002.2 GPRS: Class 8, TCP/IP

2.3 Working voltage: 8～45V DC

2.4 Working current: ≈22mA (12V DC)2.5 Working current: ≈12mA (24V DC)2.6 GPS positioning time: cold start≈26s (Open sky), warm start≈32s, hot start≈2s (Open sky)2.7 GPS positioning accuracy: 10m (2D RM)

2.8 Working ambient temperature: -20℃～+70℃

2.9 Working ambient humidity: 20%～80% RH

2.10 Dimensions: 90 (L) × 46 (W) × 14(H) mm

3. Product functions:3.1 Quad-Band Universal GSM;3.2 Ultra-Wide Input Range: 8-45V DC;3.3 Continuous GPS positioning, and GPRS real-time report;3.4 Support location enquiry through SMS;3.5 Built-in vibration sensor for intelligent vehicle anti-theft system;3.6 ACC ignition detection, with vehicle status prompted;3.7 External fuel/electricity cut-off relay for remote control of vehicle;3.8 Support three SOS specific phone numbers for remote monitoring & alarm;3.9 External SOS switch knob for emergency call;3.10 External microphone for remote voice monitoring;3.11 Built-in standby battery for alarm for illegal wire cut-off;

3.12 Red LED for power working status

Status of indicator MeaningRapid flash (flash 0.3s after every 2s) Working normally

Slow flash (flash 1s after every 2s) Low battery

3.13 Blue LED for GPS working statusStatus of indicator Meaning

Rapid flash (flash 0.3s after every 2s) GPS location successfulContinuously in bright status Searching GPS signal

3.14 Yellow LED for GSM working statusStatus of indicator Meaning

Rapid flash (flash 0.3s after every 2s) GSM / GPRS conversation start

Continuously in bright status GSM initialization4. Picture of appearance

5. Installation methods5.1 Preparation prior to installation5.11 Unpack the box to check the unit type and whether accessories are complete; if

not, please contact your local dealer.5.12 The terminal requires one GSM SIM card; for selection of SIM card, please consult your local dealer.5.13 SIM card installation: Remove the upper cover of the terminal, and open the cover of the SIM card slot, then insert SIM card into the SIM card slot with the metal face facing downwards, and lastly snap on the cover of card slot. (As shown in the following picture)

Precautions: Please use the GSM SIM card

The terminal’s SIM card requires Caller ID services The PIN code of the terminal’s SIM card is off The terminal’s SIM card requires GPRS function

5.2 Terminal’s location selection and installation The terminal is installed at a covert position; it is commended that the terminal be

installed at a covert position by a professional agent designated by the dealer; the following points shall be taken into account:5.21 The terminal shall be installed at a covert position to guard against destruction by thieves;5.22 The terminal shall be kept separate from emission source, such as parking assist device, burglar alarm or on-board communications device;5.23 The terminal can be fixed with ribbon or double-sided foam tape;

5.24 The terminal has built-in GSM antenna and GPS antenna, which shall face upwards (skywards) and is not obstructed by metal objects above; recommended positions for installation: 　 Covert position at the panel below the front windshield; 　 Covert position around the front instrument panel (non-metal material for the surface); 　 Decorative panel below the rear windshield;5.3 Line connection requirements for the terminal and its schematic diagram5.31 Standard power for this terminal is 8-45V DC; red line for positive electrode and black line for negative electrode 5.32 The negative electrode shall be separately grounded or connected to vehicle frame; DO NOT connect it to other earth wires;5.33 After the connection of power lines, pull the Power Harness Plug to area near the terminal;5.34 Covert installation; the power connection line shall adopt the original main power line connected in series with fuse box (2A FUSE), which has short-circuit protection and over-current protection.5.35 Schematic diagram for wire connection:

6. Operations of the terminal Command format for setting the following functional parameters uses the lower-case letters with English punctuation marks; all commands sent shall receive replies; information of successful setting will be given if the setting for parameter commands are successful; if not, parameters shall be reset. Location information searching function is operable for all mobile phones while the remaining functions should be through the service center.

Sending corresponding enquiry commands will receive corresponding messages from the terminal. 6.1 View location (location view function is available for all kinds of mobile phones) 6.11 Platform enquiry Note: To start this function, first set the GPRS parameter (6.10) Enter the service platform website: __________, and key in the login name and password for operations at the service platform.6.12 SMS enquiry of network links If you need to inquire the network link address of the terminal, please send "url#" to the terminal’s SIM card, which will send related information of network link at the previous time. Command: url# Example of reply message for location enquiry:

Location: Course:306,Speed:000.00,2012-10-11 16:31:39, http://maps.google

com/maps?q=N23.511980,E114.918884

6.12.1 If your mobile phone supports the internet connection, you can click on the location link through the SMS, and download the map snapshot of the terminal’s location through GPRS, WIFI or 3G networks. (This method has margin of error, since the mobile's map is inconsistent with the satellite data)6.12.2 Download the Google Earth app at http://earth.google.com/; (click on "http://earth.google.com" for more information about this app); after downloading, start the Google Earth app, as shown in the following picture: (Enter the longitude and latitude degrees at the Search Bar to locate the present location)

Note: Or, you can start Internet Explore, and enter http://maps.google.com, and then enter the longitude and latitude degrees at the Search Bar to locate the present location. (Emphasis: Data from satellite map, earth map, and planimetric map are inconsistent, with wide margin of error)

6.2 Setting phone number of the Service Center SMS setting command for the Service Center's number: pw,123456,phone number#

Example: pw,123456,13500135000# If the setting for the Service Center’s number is successful, a reply message of “Center number set successfully!”will be sent. Notes: 1. Only one phone number of the Service Center can be set 2. The Center’s number is for setting the terminal’s parameters 3. The Center’s number is for cutting off and restoring fuel/electricity functions through SMS 4. The Center’s number is for receiving service number and for setting operations from the terminal's alarm function

6.3 Deletion of Service Center’s number Command for deletion of the Center’s number: pw,123456,d# Example: pw,123456,d# If the deletion of the service Center’s number is successful, a reply message of "Center number has been deleted!" will be sent.

6.4 Password change The initial password is 123456, which can be changed by the user; the password has six digits. SMS command for password change: pw,123456# Example: pw,888888# If the setting for password change is successful, a reply message of "Password set successfully! PW:888888" will be sent.

6.5 Setting for alarm function6.51 SOS alarm6.51.1 SOS number setting SOS number can be added through sending SMS to the Center’s number: sos,no1,00000000000,no2,00000000000,no3,00000000000# Example: sos,no1,13412345678,no2,13512345678,no3,13612345678# If you only set one SOS number, set the designated number as corresponding SOS number; example: sos,no1,13412345678,# denoting setting the first number

sos,no2,13512345678,# denoting setting the second numbersos,no3,13612345678,# denoting setting the third numberIf the setting for SOS number is successful, the terminal will send a reply message of "SOS number set successfully!"

6.51.2 Deletion of SOS number For deleting a certain phone number, send the serial number command corresponding to that certain number to the terminal through SMS to delete that number. sos,no1,d,no2,d,no3,d#

6.51.3 Alarm operation through SOS number In the event of an emergency, press the SOS button to trigger the SOS emergency alarm for help. The terminal will send the alarm information to the service platform together with information about longitude and latitude degrees; and the alarm signal will be sent to the pre-set SOS numbers by making a phone; it will repeat dialing the SOS numbers; three times at maximum if the phone is unanswered. Note: For SOS alarm service, please first set the SOS number!

6.52 Vibration alarm If the power of the vehicle isn't turned on 10 minutes after the power is turned off and the ACC line of the terminal remains at low level, then the terminal automatically changes into the "protection mode"; if the protection mode is triggered, the vehicle will vibrate continuously for 5 seconds, triggering off the vibration alarm mechanism; if the vehicle power is still not turned on within 3 minutes (ACC line remains at low level), the terminal will promptly activate the vibration alarm mechanism, and send notifications to the Center’s number and the platform by sending SMS and making phones, with three alarm methods at maximum.6.52.1 Timing setting of the vibration alarm mechanism For the timing setting for the "protection mode", send the timing setting command to the terminal through SMS to set a new time; the automatic protection time in default is 10 minutes. The time set at “0” means protection is off permanently. Command format for protection: acc,time (minute)# Setting range: 0—60 minutes, “0” means protection is off permanently Example: acc,10# Reply message:ACC interval set successfully! Time: 10

6.52.2 Setting for vibration time Setting the length of continuous vibration time for alarm; the default setting is 5 seconds, which can be changed by the user. Command format: motion,5#

Reply message from the terminal: Motion time set successfully! Time: 5

6.53 Speed alarm Note: The speed alarm only send message to the platform; alarm to the Center’s number shall be made according to needs. 6.53.1 Speed alarm settings Instruction format: speed, speed # Example: speed,100# The speed alarm in the example is 100km/hour, which means when the terminal travels at a speed exceeding 100km/hour, the terminal will send alarm message to the platform. If the setting for the speed alarm is successful, a replay message of "Set speed alarm successfully" will be sent.6.53.2 Speed alarm turn-off

Command format for speed alarm turn-off: speed,d# If the setting for speed alarm turn-off is successful, a replay message of "Close speed alarm" " will be sent. 6.54 Electricity cut-off alarm The power cut-off of the terminal will trigger the electricity cut-off alarm, and the terminal will send an electricity cut-off alarm message to the pre-set Center’s number and the platform.

Note: The default state of electricity cut-off alarm is off. 6.54.1 Turn-on setting for electricity cut-off alarm Command format for turning on the electricity cut-off alarm: power,1# If the setting for turning on the electricity cut-off alarm is successful, a replay message of "Open power alarm " will be sent.6.54.2 Turn-off setting for electricity cut-off alarm Command format for turning off the electricity cut-off alarm: power,0# If the setting for turning off the electricity cut-off alarm is successful, a replay message of "Off power alarm" will be sent.

6.55 Electric fence alarm Generally, the default electric fence of the terminal is turned off; you can turn on the electric fence by sending command through SMS.6.55.1 Setting for circular fence You can set a circular fence centering on the longitude and latitude degrees of a certain point; with this point as the center of the circle and the distance as the radius, the circle thus formed is a circular fence. Entry and exit through the electric fence will trigger it by sending alarm signal to the pre-set Center’s number! Command format: fence, latitude, longitude, fence's radius# Example: fence,N22.539727,E114.091475,3# In the example is a circular fence with a radius of 300m (fence's radius 1=100m, 2=200m and so on) If the setting for a circular fence is successful, a replay message of "Set fence successfully" will be sent.6.55.2 Turning off circular fence Command for turning off circular fence: fence,d,d,d#

If the circular fence is turned off, a replay message of "Delete fence" will be sent.

6.55.3 Rectangular barrier settings Rectangular barriers are required to be set on the platform yet send alarms solely to the platform. 6.6 Fortifications and cancellation Note: This feature is sure to set the the good vibration alarm parameters (6.52) 6.61 Fortifications through SMS Sending commands to the terminal to put it in a fortified state; the terminal, while

in a fortified state, will vibrate continuously to trigger the alarm; then, the terminal will send alarm signal to the service platform and Service Center; then upload the longitude and latitude degrees to the service platform and dial the Service Center’s number; the dialing repeats three times at an interval of 6 minutes at maximum if the phone is unanswered.The terminal will send the latest information about the current address to the Service Center’s number through SMS. Protection setting command: fortify,1#

If the protection setting is successful, a reply message of "Fortification success" will be sent.6.62 Fortifications cancellation through SMS

Sending commands to the terminal will cancel the protected state; after cancellation of the protection setting, the terminal deactivates the vibration alarm function.

Cancelation command: fortify,0#If the protection cancellation of the terminal is successful, a reply message of

"Disarm success" will be sent.6.63 Fortifications cancellation through phone-making Making a phone to the terminal’s SIM card through the Center’s number will cancel the protection for the terminal and deactivate the alarm.6.7 Fuel/electricity cut-off Note: Take extreme care for this function; when operating this function, the car speed shall be less than 30km/hour; safety first.

Should the vehicle be stolen, you can send command to the terminal through the Center's number to cut off the fuel/electricity for the vehicle to immobilize the vehicle; this function can only be set through the Center’s number. Fuel/electricity cut-off command: relay,1# If the setting for fuel/electricity cut-off is successful, a reply message of "Off the petrol and power success" will be sent.6.8 Restoring fuel/electricity supply

Command for restoring fuel/electricity supply: relay,0# If the setting for restoring fuel/electricity supply is successful, a reply message of "Recovery the petrol and power success" will be sent.6.9 Setting for enquiry about parameters If you need to inquire the status of the parameters of the terminal, send "param#" SMS to the terminal’s SIM card, and the terminal will reply together with corresponding information about parameters.

Example: param# Example of reply information: SN:7893267646 URL:www.gpsjm.com PORT:8500 Inter,upload:8,sleep:0,alarm:10

6.10 Setting for GPRS parameters 6.10.1 APN Setting The APN for GSM communications operators vary according to different countries; for information about APN of your SIM card, please consult with your local communications operator. Command format: apn,network name# Example: apn,cmwap# The "cmwap" in the example denotes the APN of China Mobile operator. If the APN setting is successful, a reply message of "APN set successfully" will be sent.6.10.2 Setting for GPRS login name and password In most countries, the GPRS login name and password can be omitted; skip thisstep. For countries requiring the login name and password, make the setting asfollows: Command format: apn,netwrk name,user,loginname,pd,password# Example: apn,cmwap,user,yidong,pd,123# In the example, "yidong" denotes the login name, and "123" denotes password If the setting for GPRS login name and password is successful, a reply message of "APN set successfully" will be sent.6.11 Setting interval time for GPRS transmission of location data The default interval time for GPRS transmission of location data is 8s, namely transmitting one piece of location data to the platform server every 8 seconds. For setting interval for GPRS transmission of location data, send the command for GPRS time setting. Command format: upload,interval time(second)# Set range of interval time: 0 or 6-1800 seconds; "0" denotes no transmission of data Example: upload,15# In the example, the interval time for GPRS transmission of location data is 15 seconds, namely transmitting one piece of location data to the server every 15 seconds. If the setting is successful, a reply message of "Upload interval set of successfully! Interval time is 15" will be sent.6.12 Language and time settings The terminal supports Chinese and English display, and the time for different areas is set according to local time. Command format: lang,x,zone,n#

"x" denotes the language; "0" denotes English; "1" denotes Chine; "n" denotes time zone; the Eastern Time Zone is eight, and the UTC+08 is 8, and the UTC-03 is 3.

Example: lang,1,zone,8#"1" denotes Chinese; "8" denotes Beijing Time

6.13 Enquiry of software version Inquire information about software version of the current terminal

Command: verno# The reply message includes the software version number and date

6.14 Setting for IP address and port number of the server platform6.14.1 IP address and port number, provided by the platform operator, have already been set upon purchase of this product; consult the platform operator if you need to set these yourself. Command format: ip,120.31.131.88,port,8500#

Reply message from the terminal:IP and port set successfully!6.14.2 Change of domain can realize the communication with the server as well Command format: surl,gpsjm.com,port,8500#

A reply message from the terminal:IP and port set successfully!6.15 Terminal reset function If the GPRS link of the terminal is not working properly, e.g. the terminal fails to connect although the parameters are set correctly, you can send command to the terminal through SMS to remotely restart the terminal, so that the terminal resumes normal operation. Reset command: reset# The terminal will restart 1 minute after receiving this command. If the setting for terminal reset is successful, a reply message of "Restart successfully" will be sent.

6.16 Restore factory settings Note: This function can be operated through the Center's number If the terminal fails to work normally as a result of improper setting of the parameters, you can send the command to restore factory settings of the terminal, so that the terminal can resume normal operation. Command for restoring factory settings: factory# If the terminal receives this command, all the parameters of the terminal will restore to the factory settings, and all the manually set parameters will be void. If the setting for restoring factory settings is successful, a reply message of "Restoring factory settings successful" will be sent.

6.17 Monitoring the terminal’s surroundings Upon receiving the command sent by the Center's number, the terminal will make a phone to the pre-set phone number, which enables the user to hear the sound of the terminal's surrounding areas .� Command: monitor,phone number# Example: monitor,13500135000#

6.18 Trouble-shootinga. The terminal, after initial installation, fails to connect to the server, and the server displays "offline".

Please check the terminal's installation:1) Check whether the main power line is connected correctly; Note: Do not

connect it to the vehicle's internal control line.2) Check whether the SIM card is inserted correctly; please refer to the

installation instructions.3) Check the status of LED indicator; when working normally, the red power

indicator flashes 0.3s after every 2s; the yellow GSM indicator flashes 0.3s after every 2s; the blue GPS indictor flashes 0.3s after every 2s.

4) Check whether the GPS positioning is ready; if not, please make the initial positioning at an open area outdoors.b. The server displays the terminal in an offline state. First inspect whether the 3 indicators are working normally; if the indicators’ view is obstructed, first check the state of the SIM card, as shown below:

1) Dial the SIM card number of the terminal to check whether the phone connection is correct.

2) Check whether there is GSM network signal, as in the underground parking.3) Inspect whether the disconnection is an isolated case and determine whether

it is a fault on the part of the network operator.4) Check whether SIM card subscriber needs top-up recharge.5) Check whether the GPRS service is canceled (offline at last day of the

month).6) Inquire the parameter setting. Check the serial number of the terminal and

check whether interval time of the GPRS transmission is correct.c. If the GPS function of the terminal is activated, and yet fails to locate, please check whether the terminal is installed according to the following requirements:

1) When installing the terminal, the GPS antenna shall face skywards.2) No electromagnetic wave-absorbing substances (e.g. metal) shall be allowed

above the terminal’s installed position; it shall be especially noted that there is no explosion-proof, heat-insulating membrane on the windshield above the terminal’s position, since the membrane contains high amount of metal elements which may absorb high-frequency electromagnetic wave and reduce the signal intensity, leading to poor accuracy of positioning and, even worse, to failure of positioning.d. If there is poor GPS signal (surrounding high-rises blocking GPS signal), please drive the vehicle to an open area for location. Generally, initial location may take 1-2 minutes.e. If the GSM signal receipt is working abnormally, please check whether the SIM card in the terminal is inserted correctly; or drive to a place with GSM signal coverage, since the signal may not cover certain areas (e.g. underground parking).