-
DILO Armaturen und Anlagen GmbH Frundsbergstr. 36 D-87727
Babenhausen
Tel.: (49) 8333/302-0 Fax.: (49) 8333/302-52
Betriebsanleitung Operating instructions Instructions de
Service
fr for
pour
Dichtewchter / Dichtesensor Prfgert Density controller / Density
sensor test device
Appareil de contrle pour densimtre / palpeur de densit
Typ-Nr.: Type-no.: / No. de type: SK-509-R011
-
Dichtewchter Prfgert SK-509-R011 Betriebsanleitung
Seite 1 von 2
DILO D-87727 Babenhausen C 2391-02
1/2 Kupplungs-Nutteil DN8 mit Abdeckkappe
3 Prfbehlter 4/5 Feinregulierventil 6 Digitales Manometer fr
SF6,
Klasse 0,1, max.30 bar, Anzeige in bar, kPa,
psi, alle Anzeigen in P abs. 8 Luftventil 9 Anzeigeeinheit 10
Blechrahmen
Abmessungen: Lnge: 315 mm Hhe: 145 mm Breite: 215 mm
Bruttogewicht: 11 kg Beschreibung: Mit dem Dichtewchter - Prfgert
knnen die Schaltpunkte der Dichtewchter berprft bzw. eingestellt
werden. Die Dichtewchter werden zum Prfen auf den Pufferbehlter
(Pos. 3) aufgebaut. Bei fest aufgebauten Dichtewchtern kann nur der
momentane Schaltzustand angezeigt werden. Der Prfdruck wird am
digitalen Manometer (Pos. 6) angezeigt. Der Leuchtmelder in der
Anzeigeeinheit brennt, wenn der entsprechende Schaltkontakt
geschlossen ist. Zum Prfen wird Stickstoff oder Druckluft, die mit
Hilfe einer Pumpe erzeugt wird, ber das Luftventil Pos.8 oder die
Kupplung (Pos. 1) geleitet. Die zu prfenden Dichtewchter drfen nur
im akklimatisierten Zustand gemessen werden. Es wird empfohlen, die
Prflinge fr eine Zeit von 4 5 Stunden bei gleichbleibender
Temperatur zu lagern, bevor die Messung durchgefhrt wird. Bei der
Prfungsvorbereitung (Montage des Prflings) ist darauf zu achten,
dass die Referenzkammer des Prflings nicht berhrt wird. Es wird
empfohlen, den Prfling nur am Gehuse festzuhalten, um den Einfluss
von Krperwrme auf die Referenzkammer auszuschlieen. Whrend der
Prfung ist beim Druckablass zur Kontrolle der Schaltpunkte auf eine
angemessene Ablassgeschwindigkeit zu achten. Bei hoher
Ablassgeschwindigkeit ist die Gefahr der fehlerhaften Ablesung des
Messwertes sehr hoch. Es wird empfohlen, sich dem zu erwartenden
Schaltpunkt zgig zu nhern, um dann das Feinregulierventil so
einzustellen, dass sich die Druckanzeige langsam in 1 kPa-Schritten
bis zum Schaltpunkt verringert.
-
Dichtewchter Prfgert SK-509-R011 Betriebsanleitung
Seite 2 von 2
DILO D-87727 Babenhausen C 2391-02
Bei der Bewertung der Prfergebnisse ist gegebenenfalls die
Ungenauigkeit des Manometers (max. 3 kPa) zu bercksichtigen.
Spannungsversorgung: Eingang 90-264 V / 50 60 Hz AC Ausgang: 24 V
DC Alle Teile sind in einem Blechrahmen bersichtlich und gut
zugnglich eingebaut. Zum Anschluss des Dichtewchterprfgertes an den
Dichtewchter sind Behlter-Deckel mit Anschlusskupplung sowie
Verbindungskabel mit einem Stecker fr die Anzeigeeinheit und fr den
Dichtewchter beinhaltet. Zubehr : Deckel mit DILO-Kupplung DN8
Bestellzeichen: 3-372-R005 Deckel mit Dichtewchterkupplung
Bestellzeichen: 3-372-R006 Deckel mit ASEA-Gasanschlu
Bestellzeichen: 3-372-R008 Flanschkupplung ASEA DN20
Bestellzeichen: 3-685-R001 Verbindungskabel mit Steckern fr
Trafag-Dichtewchter Kabellnge: 0,7 m Bestellzeichen: SK-509-11
Verbindungskabel mit Steckern fr Dichtewchter WT (ABB) Kabellnge:
0,7 m Bestellzeichen: SK-509-12 Verbindungskabel mit Stecker fr
Dichtewchter WS (ABB) Kabellnge: 0,7 m Bestellzeichen: SK-509-13
Verbindungskabel mit Stecker fr Dichtewchter WD (ABB) Kabellnge:
0,7 m Bestellzeichen: SK-509-14 Verbindungskabel mit Kabelschuhen
Steckern fr Kontaktmanometer (ABB) Kabellnge: 0,7 m Bestellzeichen:
SK-509-15
-
Betriebsanleitung Digital-Manometer LEO 2-SF6-ABB
Digitales Manometer zur GasmassebestimmungGenauigkeit: 0,1 %,
FS-Typ.
EinfhrungHochspannungsschalter und Gas lsolierte Schaltanlagen
sind mit SF6-Gas gefllt.Das digitale Manometer LEO 2-SF6 misst die
Temperatur und den Druck am Gasraum und berechnet darausden Druck
bezogen auf 20'C. Dies erlaubt eine einfache und genaue Ablesung
der Gasmasse.
Gasdruck bei20'C(aktueller Druck) r ISl
lEtAktuelle Temperatur
Select-TasteiAuswahlverschiedenerFunktionen
Enler-Taste:Umschalten zwischenbefechnetem undaktuel lem
Druck
Temperatur-Sensor
BedienungDas Manometer LEO 2-SF6-ABB hat zwei Bedientasten. Mit
def l inken Taste (SELECT) werden die Funktionensowie die
Druckeinheiten angewhlt.Die rechte Taste (ENTER) aktiviert die
angewhlte Funktion oder Druckeinheit.ber die rechte Taste kann auch
zwischen dem berechneten (auf 20 'C) und aktuellen Druck
gewechseltwerden.Achtung: Da der Temperatursensor direkt unterhalb
des eigentlichen Manometers install iert ist, ist darauf zuachten,
dass das Manometer NICHT dod gehalten wird, weil sonst
Temperaturmessungen verflscht werdenknnen !
Einschalten: Ein Druck auf SELECT schaltet das Gert ein. Das
Display zeigt aufeinanderfolgend dieSoftwareversion (Jahr,Aivoche),
den werkseitig abgeglichenen Druckbereich und den aktuellen Druck
oben an.Das Gert verfgt ber folgende Funktionen:_ OFF : Schaltet
das Gert aus- MANO: Gibt nachstehende Funktionen ireil
ZERO SEt: Setzt einen neuen NullpunktZERO rES: Setzt den
Nullpunkt auf WerkseinstellungCONT on: Deaktiviert die automatische
AusschaltfunktionCONT off: Aktiviert die automaiische
Ausschaltfunktion (das Gertschaltet sich 15 lvlin. nach der letzten
Tastenbeltigung automatisch aus)Danach folgt die Einheiienwahl:
bar, kPa, psi, alle Anzeigen in pabs
,4**{
1
KELLER AG St. Gallerstrasse 119KELLER GmbH
Schwarzwaldstrasse
CH-8404 Winterthur17 D-79798 Jestetten
Tel. 052 235 25 25rel. 07745 92140
Fax 052 235 25 00Fax 07745 9214 50
Seite I 08.09.2004
-
Betriebsanleitung Digital-Manometer LEO 2-SF6-ABBBeisoielSetzen
einer neuen Druckeinheit (2.b. PSI):-> Einschalten des Gertes
durch kuzes Drcken von SELECT.--> Warten, bis Gert im Messmodus
ist (ca.3 Sekunden)--> 3 x drcken der SELECT-Taste: MANO
erscheint.--> Druck auf ENTER: ZERO SEt erscheint.--> Druck
auf SELECT: ZERO rES erscheint.-> Druck auf SELECT: CONTon oder
CONT off erscheint.--> Druck auf SELECT: BAR erscheint.->
Druck auf SELECT: PSI erscheint.-> Druck auf ENTER: Die neue
Druckeinheit ist qesetzt. Das Gert befindet sich wieder im
Messmodus.
Anzeige des aktuellen Druckwertes- Beflndet sich das Gert im
Messmodus (oben: berechneter Druck bei 20 'C, unten: Temperatur),
wird durchDrcken der ENTER-Taste der aktuelle Druck fr 5 Sekunden
angezeigt.
Hinweise'1) Die Funktionen und Einheiten knnen auch durch
konstantes Drcken def SELECT-Taste angewhlt unddurch Loslassen zuf
Aktivierung freigegeben werden-
2) Wird die angewhlte Funktion oder Einheit nicht innerhalb von
5 Sekunden durch die ENTER-Taste aktiviert,kehrt LEO 2-SF6-ABB ohne
Anderung einer Einstellung in den Messmodus zurck.
3) Das Aus- und Einschalten von LEO 2-SF6-ABB ndert nichts an
den zuvor gettigten Einstellungen.4) lst die CONf or Funktion
aktiviert, wird dies im Display blinkend angezeigt.5) Kann ein
Druck auf dem Display nicht dafgestellt werden, erscheint OFL oder
UFL auf der Anzeige.6)Wird ein Druck ausserhalb des l\ressbereiches
des Gertes angelegt, wird der letzte gltige Druckwertblinkend
angezeigt.
7) Erscheint Errim Display, ist die SF6-Gas Fllung nicht in
einem gasfrmigen Zustand und der Druck bei20"C kann somit nicht
berechnet werden.
lnstallation
Das digitale Manometer LEO 2-SF6-ABB hatein7l16" UNF Gewinde.Die
mitgelieferte Verschraubung erlaubt die Ausrichtung des
l,4essgertes in die jede Position.
Batteriewechsel / Baft erle-Lebensdauer-- Bei schwacher Batterie
leuchtet oben links das Batteriesymbol (BAT LOW) auf.-
Batteriewechsel; Batteriefach ffnen und die Batterie (Typ CR
2430)wechseln. Achten Sie darauf, dass derO-Ring sauber im
Verschlussdeckel I iegt.- Die Batterie-Lebensdauer betrgt 1000
Stunden bei kontinuierl ichem Betrieb.
Bereiche / Abgleich- Die Werkseinstellung des Nullpunktes fr die
Bereiche -1 ...3 bar oder -1 ...30 bar ist bei 0 bar absolut.
FrReferenzdruckmessungen "ZERO SEt" aktivieren bei Umgebungsdruck.-
Gerte mit Bereichen ber 30 bar werden bei Umgebungsdruck
abgeglichen.
www.kellef-druck.com 06 / 2003
KELLER AG St. Gallerstrasse 119 CH-8404 Winterthur fel052235 25
25 Fax 052 235 25 00KELLER GmbH Schwarzwaldstrasse 17 D-79798
Jestetten Tel. 07745 92140 Fax 077 45 9214 50
Seite 2 08.09.2004
-
Density controller test device SK-509-R011 Operating
instructions
Page 1 of 2
DILO D-87727 Babenhausen C 2392-02
1/2 Coupling groove part DN8 with covering cap
3 Test tank 4/5 Precision valve 6 Digital gauge for SF6,
class 0.1, max. 30 bar, indication in bar, kPa,
psi, all indications in P abs 8 Air valve 9 Indicating element
10 Metal frame
Dimensions: Length: 315 mm Height: 145 mm Width: 215 mm Gross
weight: 11 kg Description: The density controller test device
allows verification and setting of the switching points of the
density controllers. For testing, the density controllers are
mounted onto the test tank pos. 3. In case of firmly mounted
density controllers only the present switching condition can be
indicated. The test pressure is shown on the digital gauge pos. 6.
The indicator light on the indicating element lights up if the
corresponding switching contact is closed. For testing, the
nitrogen or compressed air, which is generated by using a pump
passes through the air valve pos. 8 or coupling pos. 1. The density
controllers to be tested should only be measured in acclimatized
condition. Prior to carry out the measurement it is recommended
storing the specimen for 4 5 hours at constant temperature. When
preparing the test (assembly of the specimen) pay attention that
the reference chamber of the specimen is not touched. It is
recommended only holding the specimen to the housing so that the
reference chamber is not influenced by body heat.
-
Density controller test device SK-509-R011 Operating
instructions
Page 2 of 2
DILO D-87727 Babenhausen C 2392-02
Pay attention to the appropriate release velocity (to be set via
the precision valve) during the test when pressure is released for
controlling the switching points. In case of fast decrease of
pressure the indication might be incorrect. It is recommended
reaching the switching point to be expected as fast as possible and
set the precision valve so that the pressure falls slowly in
increments of 1 kPa until the switching point is reached. For
evaluating the test results take the inaccuracy of the gauges (max.
3 kPa) into consideration. Power supply: Input: 90-264 V / 50/60 Hz
AC Output: 24 V DC All parts are installed into a sheet metal
frame, well arranged and easily accessible. For the connection of
the density controller test device to the density controller, tank
covers with connecting coupling as well as connecting cables with a
plug for the indicating element and for the density controller are
included. Accessories: Cover with density controller DILO coupling
DN8 Order no.: 3-372-R005 Cover with density controller coupling
Order no.: 3-372-R006 Cover with ASEA gas connection Order no.:
3-372-R008 ASEA flange coupling DN20 Order no.: 3-685-R001
Connecting cable with plugs for Trafag density controller Cable
length: 0.7 m Order no.: SK-509-11 Connecting cable with plugs for
density controller WT (ABB) Cable length: 0.7 m Order no.:
SK-509-12 Connecting cable with plug for density controller WS
(ABB) Cable length: 0.7 m Order no.: SK-509-13 Connecting cable
with plug for density controller WD (ABB) Cable length: 0.7 m Order
no.: SK-509-14 Connecting cable with cable lug plugs for contact
gauge (ABB) Cable length: 0.7 m Order no.: SK-509-15
-
Operating Instructions Digital-ManometerLEO 2-SF6-ABB
Digital manometer for Density controlClass 0,1, FS-Type.
lntroductionHigh Voltage Circuit Breakerc and Gas Insulated
Switchgears are fi l led with SF6-Gas.The manometer LEO 2-SF6-ABB
is measuring the temperature and the pressure at the gas
compartementsand is calculating the pressure in relation to 20'C.
This allows easy reading of the gas density.
gaspressure at 20'C(actual pressure)
actualtemperature
Select-bottom:selection ofdifferentfunctions
Enter-bottom:switches betweencalculated andmeasured pressure
temperature-sensor
OperatingThe manometer LEO 2-SF6-ABB has two operating keys. The
left key (SELECT) serves to select the functionsand the pressure
units.The right key (ENTER) activates the selected function or
pressure unit.The right key is also used to switch between the MM.-
and MlN. value
Attention: The temperatursensor is directely installed at the
bottom of the manometer housing. To avoid rapidtemperatur changings
due to holding the manometer near the sensor, the manometer should
either be hold atthe rubber protection or at the attached hose.
Turn-on: Pressing the SELECT key turns the instrument on. The
instrument subsequently display the softwareversion (yearlweek),
the tull-scale pressure range, the actual pressure (top display)
and the last measuredMAX.-value.
The instrument has the following functions:- OFF: Turns offthe
instrument- MANO: Releases the following functions:
ZERO SEt: Sets a new Zero referenceZERO rES: Sets the Zero to
factory settingsCONT onr Deactivates the automatic turn-off
functionCONT off: Activates the automatic turn-off function. (the
instrumenttums off 15 minutes after the last key funcllon)followed
by the unit selection; bar, kPa, psi, all measurements in pabs
KELLER AG St. Gallerstrasse 119KELLER GmbH
Schwarzwaldstrasse
CH-8404 Winterthur17 D-7979B Jestetten
Page 1
fel. 052 235 25 25 Fax 052 235 25 OOTe|.07745 92140 Faxo7745
9214 50
08.09.2004
-
Operating Instructions Digital-ManometerLEO 2-SF6-ABB
ExamoleSetting a new pressure unit (e.9. PSI):--> Turn on the
instrument by shortly pressing the SELECT-key--> Wait lor the
instruments measuring mode (approx. 3 seconds)*> Press the
SELECT-kex 3 times: MANO aooears-> Press ENTER: ZERO SEt
aooears-> Press SELECT: ZERO rES aDpears-> Press SELECT: CONT
on or CONT off appears-> Press SELECT: BAR aooears-> Press
SELECT: PSI appears-> Press ENTER: The new pressure unit is set.
The instrument returns to the measuring mode.
Display of the minimum pressure value- When the measuring mode
(Display: Actual pressure and Max.-Value), you may display the
l\4in.-value for 5seconds by shortly pressing the ENTER-key.
Noles'1) The functions and units can also be called up by
keeping the SELEcT-key depressing. Releasing the keyenables the
displayed function or unit to be activated with the ENTER-key.
2) lf the selected function or unit is not activated within 5
seconds with the ENTER-key, LEo 2 retums to themeasuring mode
without changing any settings.
3) Turning LEO 2 on and off does not influence any of the
previous settings.4) lf the CONT on function is activated, it is
indicated with a flashing sign on the display.5) lf a pressure can
not be represented on the display, OFL (overflow) or UFL
(underflow) appears on thedisplay.
6) lf the actual pressure goes beyond the measuring range, the
last valid pressure value starts flashing on thedisplay.
7) lf Enappears in the display, the SF6-Gas fi l l ing is not in
a gaseous form and can therefore not be displayed.lnstallalionThe
digital Manometer LEO 2-SF6-ABB is equipped with a 7/16" UNF
thread.The adapter, delivered with the instrument allows the
installation in any direction.
Battery Change / Battery Life- When the battery starts
weakening, a low battery warning (BAT LOW) will appear in the upper
left cornef ofthe display.- Battery Change: Open the battery
compartement and change the battery (type CR 2430). Make sufe that
theO-Ring remains embedded in the cover.- The battery l ife is
'1000 hours in nofmal measuring mode.
Ranges / calibration- The factory setting of the ZERO for the
ranges -'1..3bar or -1...30bar is at obar absolute. For sealed
gaugepressure measurements, activate "ZERO Set" at ambient
pressure.-- Instruments with ranges >30 bar are calibrated in a
sealed gauge mode at ambient pressure.
www.keller-druck.com 06 / 2003
KELLER AG St. Gallerstrasse 1 19 CH-8404 Winterthur fe|.052235
25 25 Fax 052 235 25 OOKELLER GmbH Schwarzwaldstfasse 17 D-79798
Jestetten Tel. 077 45 92140 F ax 077 45 9214 50
Page 2 08.09.2004
-
Appareil de contrle pour densimtre SK-509-R011 Instructions de
service
Page 1 de 2
DILO D-87727 Babenhausen C 2393-02
1/2 Elment rainure du raccord-coupleur DN8 avec chapeau
3 Rservoir de test 4/5 Vanne de rglage fin 6 Manomtre numrique
pour SF6,
classification 0,1, max.30 bar,
indication en bar, kPa,
psi, toutes les indications en P abs. 8 Soupape air 9 Unit
dindication 10 Cadre mtallique
Dimensions: Longueur: 315 mm Hauteur: 145 mm Largeur: 215 mm
Poids brut: 11 kg Description: Lappareil de contrle pour densimtre
sert contrler ou ajuster les points de contact de commutation des
densimtres. Pour le test, les densimtres sont installs sur le
rservoir de test (pos. 3). Si les densimtres sont monts firmament
seulement l'tat de commutation instantan peut tre indiqu. La
pression d'preuve est indique au manomtre numrique (pos. 6). Le
voyant lumineux dans l'unit d'indication s'allume si le contact de
commutation correspondant est ferm. Pour le test on utilise de
lazote ou de l'air comprim gnr l'aide dune pompe sur la soupape air
qui est conduit sur le coupleur (pos. 1). Les densimtres vrifier
doivent tre seulement mesurs en condition acclimate. Avant la
mesure il est recommand de stocker les prouvettes sous une
temprature constante pour 4 5 heures. Pendant la prparation de la
vrification (installation de lprouvette) veuillez ce que la chambre
de rfrence de lprouvette ne soit pas touche. Il est recommand de
porter lprouvette seulement au botier pour que la chambre de
rfrence ne soit pas influence par la chaleur corporelle.
-
Appareil de contrle pour densimtre SK-509-R011 Instructions de
service
Page 2 de 2
DILO D-87727 Babenhausen C 2393-02
Pour contrler les points de commutation faire attention une
vlocit dchappement convenable (ajustable par la vanne rglage fin)
lors dune pression dchappement. Au cas o la pression baisse
rapidement lindication pourrait tre incorrecte. Il est recommand
dobtenir le point de commutation atteindre le plus vite possible et
ajuster la vanne de rglage de sorte que la pression baisse
lentement dans les incrments de 1 kPa jusqu ce que le point de
commutation soit atteint. Pour lvaluation des rsultats de
vrification prendre en considration limprcision du manomtre (max. 3
kPa). Alimentation en courant: Entre: 90-264 V / 50 60 Hz courant
alternatif / Sortie: 24 V courant triphas Toutes les pices sont
installes bien disposes et bien accessibles dans un cadre en
d'acier. Pour le raccordement de l'appareil de contrle pour
densimtre au densimtre des couvercles de rservoir avec des
coupleurs de raccordement ainsi que des cbles de raccordement avec
une fiche pour l'unit d'indication et pour le densimtre sont
inclus. Accessoires : Couvercle avec coupleur DILO DN8 No. de
commande: 3-372-R005 Couvercle avec coupleur pour densimtre No. de
commande: 3-372-R006 Couvercle avec raccord ASEA No. de commande:
3-372-R008 Coupleur bride ASEA DN20 No. de commande: 3-685-R001
Cble de raccordement avec fiches pour densimtre Trafag Longueur de
cble: 0,7 m No. de commande: SK-509-11 Cble de raccordement avec
fiches pour densimtre WT (ABB) Longueur de cble: 0,7 m No. de
commande: SK-509-12 Cble de raccordement avec fiche pour densimtre
WS (ABB) Longueur de cble: 0,7 m No. de commande: SK-509-13 Cble de
raccordement avec fiche pour densimtre WD (ABB) Longueur de cble:
0,7 m No. de commande: SK-509-14 Cble de raccordement avec cosses
de cble fiches pour manomtre contact (ABB) Longueur de cble: 0,7 m
No. de commande: SK-509-15
-
Manuel d'utilisation Manometre Digital LEO 2-SF6-ABB
Manomtre digital pour la d6finition de la masse de gazPr6cision:
0,1 %, EM-Typ.
lntroductionInterrupteurs de haute tension et sous-stations
isol6es au gaz sont remplies de gaz SF6Le manomtre num6rique LEO
2-SF6 mesure la tempdrature et la pression la chambre de gaz et
calcule lapression par rapport 20'C. Ceci permet une lecture simple
et exacte de la masse de gaz.
Pression 20"C(pression actuelle)
Temperature actuelle
Touche-Select:56lection dedivers fonctions
Touche-Enter:Changement entre lapression calcul6e et lapression
aciuelle
Capteur detemp6rature
UtilisationLe manomtre LEO 2-SF6-ABB deux touches de fonction.
La touche de gauche (SELECT) permet des6lectionner les fonctions et
I'unite de pression. La touche de droite (ENTER) valide la fonction
ou I'unit6 demesure s6lectionne. Cette meme touche permet galement
de basculer entre la press;on calcul6e ( 20'C) etla pression
actuelle.
Attention: Le capteur de temprature est situ directement en
dessous du manomtre luj mme. Pour ce fait,il est n6cessaire de
faire attention ne pas tenir le manomtre dans cet endroit. Le
capteur pourrait s'echaufferet falsifier la mesure de temprature
!
Mise en route : Une action sur SELECT met en route l'instrument.
Le manomtre affiche successivement laversion de programme
(ann6e/semaine), l '6tendue de mesure calibree en usine et la
pression actuelle (partjesuo6rieure).L'insirument dispose des
fonctions suivantes I
Anete I'instrument- MANO: Donne accs aux fonctions
suivantes:
ZERO SEt: Enregistre un nouveau 2610 de r6f6rence,ZERO rES:
Restaure le zro calibrd en usine.CONT on: D6sactive la fonction
arrt automatique de I'instrument.CONT offl Active la fonction arret
automatique de l'instrument(l'appareil s'arrCte automatiquement 15
min aprs la dernire action sur une touche)En suite, slection de
I'unit6: bar, kPa, psi, tous les affichages en pabs
KELLER AG St. Gallerstrasse 119KELLER GmbH
Schwarzwaldstrasse
CH-8404 Winterthur17 D-79798 Jestetten
Page '1
Tel. 052 235 25 25 Faxos223525OOfel. 07745 92140 Fax 07745 9214
50
,t7.11.2004
-
Manuel d'utilisation Manometre Digital LEO 2-SF6-ABB
ExempleEnregistrement d'une nouvelle unit6 (p.ex. PSI):->
Mise en route par une action brve sur SELECT.-> Attendre que
I'instrument passe en mode mesure (env. 3 secondes).-> Appuyer 3
fois sur la touche SELECT : MANO s'afliche.-> Appuyer sur ENTER:
ZERO SEt s'affiche.-> Appuyer sur SELECT: ZERO rES
s'affiche.-> Appuyer sur SELECT: CONT on ou CONT off
s'affiche.-> Appuyer sur SELECT: BAR s'affiche.-> Appuyer sur
SELECT: PSI s'affiche.-> Appuyer sur ENTER: La nouvelle unite
est enregistr6e.L'instrument se trouve nouveau en mode mesure.
Affichage de la valeur de pression actuelle- Si I'instrument se
trouve en mode mesure (partie sup6rieure: pression calculee 20 'C,
partie inferieure:temp6rature), une action sur la touche ENTER
permet d'afficher la pression actuelle pendant 5
secondes.Remarques1) Les fonctions et unites peuvent galement otre
appeles par une action maintenue sur la touche SELECT
ets6lectionnees ds relchement de la touche.2) Si la fonction ou
I'unit6 choisie n'est pas valid6e dans les 5 secondes avec la
touche ENTER, le manomtreLEO 2-SF6-ABB bascule automatiquement,
sans modification des 169lages, en mode mesure.3) La mise en route
et I'arrt de LEO 2-SF6-ABB ne modifient pas les r6glages
precedemment valid6s.4) La fonction CONT on active est indiquee par
un clignotement l'6cran.5) Si une pression ne peut Ctre affich6e,
le message OFL (overflow) ou UFL (underflow) apparait l'cran.6) Si
une pression se situant en dehors de l'6tendue de mesure de
I'instrument est applique, la dernirevaleur de pression est afiiche
clignotante.7) Si Err s'affiche, le remplissage gaz SF6 n'est pas
en forme gazeuse et la pression 20'C ne peut pas 6trecalcule.
lnstallation
Le manomtre digital LEO 2-SF6-ABB possde un raccord 7/16"
UNF.Chaque manomtre est livre avec un adaptateur '1l4" gaz mle qui
permet une orientation optimale del'aooareil.
Remplacement de la batterie / Dur6e de vie de la bafterie- Une
batterie faible est signl6e par le sigle batterie (BAT LOW) dans la
partie sup6rieure gauche de l'ecran.- Remplacement de la batterie:
ouvrir le compartiment de la batterie et remplacer la batterie (Typ
CR 2430).Veillez ce que le joint torique soit propre et
correctement place dans le couvercle de fermeture.- La dur6e de vie
de la batterie est d'environ 1000 heures en fonctionnement
continu.
Etendues de mesure, calibration- Le reglage d'usine du zero des
6tendues de mesure -1...3 bar et -1...30 bar est effectue 0 bar
absolu.Pour une mesure de pression relative activer la fonction "
ZERO SET " la pression atmospherique.-- Les manomtres d'6tendue de
mesure > 30 bar sont calibrs la pression atmosphOrique du jour
del'6talonnage.www.kellerdruck.com 06 / 2003
KELLER AG St. Gallerstrasse 119 CH-8404 Winterthur fel O52 235
25 25 Fax 052 235 25 00KELLER GmbH Schwazwaldstrasse '17 D-79798
Jestetten Tel. 07745 92140 Fax07745 9214 50
Paae2 17.11.2004
-
SK-509-R011DEUTSCHLEO Digital-ManometerMini-Fu-Pumpe
ENGLISHLEO Digital-ManometerMini foot pump
FRANCAISLEO Manometre DigitalMini-pompe pied