– + - 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 - - 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 - - 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 - – + SITRANS P300 avec HART Instructions (Leporello) A5E34318018-01, 03/2014 Avant l'installation et la mise en service, veuillez respecter les Instructions de service ! ! ou Appliquer la pression de référence. Raccorder l'ampèremètre continu (recommandé). Compartiment de raccordement 5s Verrouillage clavier, protection en écriture désactivée Clavier (Commande Sans Ecran) Affichage numérique LL Verrouillage Clavier (Validations Via HART) LS Activation MA+ME possible LO uniq Activation MA possible LA Clavier LA verrouillé L Protection en écriture C Fonctionnement En Courant Constant 15 Affichage de la communication 14 Valeur limite sup dépassée 13 Signe pour valeur mesurée 12 Valeur limite inf non atteinte 11 Mode/ Verrouillage Clavier 9 Unité/Bargraphe 8 Valeur Mesure 7 Touche Décrémentation 6 Touche Incrémentation 5 Touche Mode 4 Connecteur test pour ampèremètre continu 3 (-)Energie auxiliaire 2 (+)Energie auxiliaire 1 Connexion blindage Légende 1-15 4) 1) DM=Début Mesure FM=Fin Mesure enregistrer valeur Commande M7 Etalonnage point zéro 1)2)4) M6 Réglage en aveugle FM 1)2)4) M5 Réglage en aveugle DM 1)2)4) M4 Réglage atténuation 1)2)4) M3 Définir et régler FM 1)2)4) M2 Définir et régler DM 1)2)4) Mode affichage en mA % pression définir valeur / modifier valeur Commande M14 mA % unité 1)2)4) M13 mA % affichage valeur mesure 1)2) M10 Verrouillage clavier, protection en ecriture 1)2) M9 Courant défaut sup./inf. 1)2)4) M8 Générateur courant, u. 2s 2)3) 3) 2) , quitter sans enregistrer 14 11 16 bar 18 18 bar 20 mA 20 mA 16 bar 20 mA 18 4 2 0 4 2 0 4 0 14bar-2bar 11 bar-2bar *16mA+4mA=16mA I= Condition : voir les instructions de service Chapitre 6. Définir début et fin de mesure CalculerCourantSortie(p.ex.11 bar) Définir fin de Mesure (p. ex. 14 bar) Définir Début de Mesure (p. ex. 2 bar) Situation de départ et maintenir appuyés pendant 2 s pour la calibration à 20 mA. Appliquer la pression correspondant au DM au transmetteur. et maintenir appuyés pendant 2 s pour la calibration à 4 mA. Définir début mesure : Choisir mode 02 Noter : les touches de commande peuvent être verrouillées ! Désactivation du verrouillage du clavier, voir -3-. Appliquer la pression correspondant à la FM au transmetteur. Définir fin mesure : Choisir mode 03 Appliquer la pression de référence. Raccorder l'ampèremètre continu (recommandé). Réglalge du courant selon la formule de calcul disponible dans les instructions de service, chapitre 6. Définir début mesure : Choisir mode 02 Ajuster à l'aide des touches et (réglage dynamique) et enregistrer le DM avec la touche . Ajuster à l'aide des touches et (réglage dynamique) et enregistrer la FM avec la touche . Avec et (2s) régler la fin de mesure ou limite supérieure du capteur et enregistrer avec . Définir fin mesure en "Aveugle" :Choisir mode 06 Avec et (2s) régler le début de mesure ou limite inférieure du capteur et enregistrer avec . Définir début mesure en "Aveugle" : Choisir mode 05 Avec et régler la pression correspondant à la FM (réglage dynamique) et enregistrer avec . Régler fin mesure en "aveugle" : Choisir mode 06 Avec et , régler la pression correspondant au DM (réglage dynamique) et enregistrer avec . Régler début mesure en "Aveugle" : Choisir mode 05 enregister avec définir le point zéro avec et Etalonnage point zéro: Choisir mode 07 Purger le transmetteur ou régler une pression référence connue (pression absolue <0,1 ‰ de etendue mesure). Voir instructions service et certificats conformité! http://www.siemens.com/sitransp Données Ex HW: xx.yy.zz FW: aa.bb.cc Figurent sur plaque homologation. Code FW/HW Connexion transmetteur (4) Charge (3) Energie auxiliaire U H (2B) Blindage sur presse-étoupe (2A) Connexion de blindage pour presse-étoupe en plastique (1) Bornes de connexion Régler fin mesure : Choisir mode 03 Leporello (- 2 -) (- 3 -) 2 3 1 Mode UP ZERO SPAN MODE 7 6 5 DOWN 15 14 13 12 11 9 8 D C B A UP DOWN MODE UP DOWN MODE (3) (4) (2B) (2A) (1) UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN UP DOWN MODE MODE MODE MODE UP DOWN UP DOWN MODE UP DOWN MODE 4 MODE M11 Régler courbe caractéristique ("Lin") 1)2)4) SITRANS P300 mit HART Kurzanleitung (Leporello) A5E34318018-01, 03/2014 Vor der Installation und der Inbetriebnahme ist die Betriebsanleitung zu beachten! ! oder Referenzdruck anlegen Gleichstrommessgerät anschließen (wird empfohlen) Anschlussraum 5s Tastatursperre, Schreibschutz AUS Tastatur (Bedienung ohne Display) Digitalanzeige LL Tastatursperre (Frei- gabe nur über HART) LS MA + ME setzbar LO nur MA setzbar LA Tastatur gesperrt L Schreibschutz C Konstantstrombetrieb 15 Kommunikationsanzeige 14 Oberer Grenzwert überschritten 13 Vorzeichen für Messwert 12 Unterer Grenzwert unterschritten 11 Modus/ Tastensperre 9 Einheit/Bargraf 8 Messwert 7 Taste Decrement 6 Taste Increment 5 Taste Mode 4 Teststecker für externes Gleichstrommessgerät 3 (-) Hilfsenergie 2 (+) Hilfsenergie 1 Schirmauflage Legende 1-15 4) 1) MA=Messanfang ME=Messende Wert speichern Bedienung M7 Nullpunktabgleich 1)2)4) M6 ME blind einstellen 1)2)4) M5 MA blind einstellen 1)2)4) M4 Dämpfung einstellen 1)2)4) M3 ME setzen u. einstellen 1)2)4) M2 MA setzen u. einstellen 1)2)4) Anzeigemodus in mA % Druck Wert setzen / Wert ändern Bedienung M14 mA % Einheit 1)2)4) M13 mA % Messartanzeige 1)2) M10 Tastensperre, Schreibschutz 1)2) M9 Fehlerstrom oben/unten 1)2)4) M8 Stromgeber, u. 2 s 2)3) 3) 2) ,Beenden ohne Speichern 14 11 16 bar 18 18 bar 20 mA 20 mA 16 bar 20 mA 18 4 2 0 4 2 0 4 0 14 bar - 2 bar 11 bar - 2 bar * 16 mA + 4 mA = 16 mA I = Voraussetzung: siehe Betriebsanleitung Kapitel 6. Messanfang und Messende setzen Ausgangsstrom berechnen (z. B. 11 bar) Messende setzen (z. B. 14 bar) Messanfang setzen (z. B. 2 bar) Ausgangs- situation und 2 s gedrückt halten und damit ME auf 20 mA setzen Druck, der dem MA entspricht, auf den Messumformer geben und 2 s gedrückt halten und damit MA auf 4 mA setzen Messanfang setzen: Modus 02 wählen Hinweis: Die Bedientasten können gesperrt sein! Tastatursperre aufheben siehe Seite -3-. Druck, der dem ME entspricht, auf den Messumformer geben Messende setzen: Modus 03 wählen Referenzdruck anlegen. Gleichstrommessgerät anschließen (wird empfohlen) einzustellender Strom gemäß Berechnungsformel siehe Betriebsanleitung Kapitel 6 Messanfang einstellen: Modus 02 wählen Mit oder MA einstellen (Verstelldynamik) und mit MA speichern Mit oder MA einstellen (Verstelldynamik) und mit MA speichern drücken,Wert speichern drücken, Wert speichern mit und (2s) das Messende auf das obere Sensorlimit setzen Messende "blind" setzen: Modus 06 wählen mit und (2s) den Messanfang auf das untere Sensorlimit setzen Messanfang "blind" setzen: Modus 05 wählen drücken, Wert speichern mit oder den Druck einstellen, der ME entsprechen soll (Verstelldynamik) Messend "blind" einstellen: Modus 06 wählen drücken, Wert speichern MODE mit oder den Druck einstellen, der MA entsprechen soll (Verstelldynamik) Messanfang "blind" einstellen: Modus 05 wählen drücken, Wert speichern den Nullpunkt setzen. mit und Nullpunkt abgleich: Modus 07 wählen Messumformer belüften oder bekannten Referenzdruck einstellen. (Absolutdruck < 0,1 ‰ der Messspanne.) siehe Betriebsanleitung und Konformitätsbescheinigungen! http://www.siemens.com/sitransp Ex-Daten sind auf dem Zulassungsschild abzulesen. FW/HW-Kennzeichen Messumformer anschließen (4) Bürde (3) Hilfsenergie U H (2B) Schirm auf Kabelverschraubung (2A) Schirmauflage bei Kunststoffkabel- verschraubung (1) Anschlussklemmen Messende einstellen: Modus 03 wählen M11 Kennlinie einstellen ("Lin") 1)2)4) SITRANS P300 with HART Quick Start Guide (Leporello) A5E34318018-01, 03/2014 Please refer to the Operating Instructions prior to installation and start up! ! Leporello (- 2 -) (- 3 -) 2 4 3 1 Connection Box 2 4 3 1 UP DOWN ZERO SPAN Mode 5s Read-only OFF Keyboard disable MODE 7 6 5 Keyboard (setting without display) 15 14 13 12 11 9 8 Digital display able only via HART) LL Keyboard disable (en- LS MA + ME can be set LO Only MA can be set LA Keyboard disabled L Read-only C Constant current mode (15) Communication display (14) Violation of higher limit (13) Symbol for measured value (12) Violation of lower limit (11) Mode/button lock (9) Unit/bar graph (8) Measured value (7) Decrement key (6) Increment key (5) Mode key (4) Test plug for external DC ammeter (3) (-) power supply (2) (+) power supply (1) shield support Legend 1-15 MA = zero point ME = limit point 4) 1) 1) 2) 4) 1) 2) 4) 1) 2) 4) 1) 2) 4) 1) 2) 4) 1) 2) 4) M7 Zero adjustment M6 Adjust ME without pressure M5 Adjust MA without pressure M4 Adjust damping M3 Set and adjust ME M2 Set and adjust MA Display mode in mA % pressure Operation Save value MODE / Change value UP DOWN 1) 2) 4) 1) 2) 1) 2) 1) 2) 4) M14 mA % dimension M13 mA % measuring mode M10 Keyboard disabling, read-only M9 Fault current upper/lower M8 Current transm., and for 2 s 2)3) or change value UP DOWN Operation 3) 2) ,exit without saving MODE r Prerequisite: see Operating Instructions Section 6 scale and full scale Setting start of Calculating output current (p. e. 11 bar) D (p. e. 14 bar) scale Setting full C (p. e. 2 bar) of scale Setting start B situation Initial A 14 bar - 2 bar 11 bar - 2 bar I= * 16 mA + 4 mA = 16 mA 11 14 16 bar 18 18 ba 20 mA 20 mA 16 bar 4 18 20 mA 0 2 4 0 2 4 0 r and press and hold for 2 s to set ME to 20 mA UP DOWN Apply reference pressure Connect DC ammete and press and hold for 2 s to set MA to 4 mA UP DOWN Setting start of scale: Select mode 02 Note: the keys may be disabled! Remove key board disabling See page -3-. Apply pressure corresponding to ME to the transmitter. Setting full scale: Select mode 03 Adjust MA using and (variable speed) and save ME using Apply reference pressure Connect DC ammeter (recommended) Adjusting full scale: Select mode 03 Apply reference pressure. Connect DC ammeter (recommended) Adjust current according to calculation formula,see Operating Instructions, Section 6 Adjusting start of scale Select mode 02 Adjust MA using and (variable speed) and save MA using Set full-scale value to the upper sensor limit using and (2 s). Press to save value. Setting full scale without application of pressure: Select mode 06 Set start-of-scale value or the lower sensor limit using and (2 s). Press to save value. Setting start of scale without application of pressure: Select mode 05 Adjust pressure which is to correspond to MA using and (variable speed) Press to save value Adjust pressure which is to correspond to ME using and (variable speed). Press to save value. Adjusting full scale without application of pressure: Select mode 06 Adjusting start of scale without application of pressure: Select mode 05 Zero point adjustment: Select mode 07 See Instruction Manual and conformity certificates! http://www.siemens.com/sitransp Ex Data Can be read from the approval label FW/HW releases Connecting the transmitter (4) Load (3) Auxiliary power U H (2B) Shield on cable gland (2A) Shield support with plastic cable gland (1) Supply terminals MODE UP DOWN MODE UP DOWN MODE UP DOWN MODE UP DOWN MODE UP DOWN MODE MODE UP DOWN UP DOWN Set Zero using and Press to save value. HW: xx.yy.zz FW: aa.bb.cc HW: xx.yy.zz FW: aa.bb.cc Vent transmitter (pressure, differential ressure, flow, level) or evacuate (absolute presssure <0.1 ‰ of span) M11 Adjust characteristic ("Lin") 1)2)4) Leporello (- 2 -) (- 3 -) 2 3 1 Mode UP ZERO SPAN MODE 7 6 5 DOWN 15 14 13 12 11 9 8 D C B A UP DOWN MODE UP DOWN MODE (3) (4) (2B) (2A) (1) – + (3) (4) (2B) (2A) (1) UP DOWN UP DOWN UP DOWN UP DOWN MODE UP DOWN MODE MODE UP DOWN MODE UP DOWN UP DOWN MODE UP DOWN MODE 4
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
–+
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
–+
SITRANSP300 avec HARTInstructions (Leporello)A5E34318018-01, 03/2014
Avant l'installation et la mise en service, veuillez respecter les Instructions de service !
!
ou
Appliquer la pression de référence.Raccorder l'ampèremètre continu (recommandé).
Compartiment de raccordement
5 s Verrouillage clavier, protection en écriture désactivée
Clavier(Commande Sans Ecran)
Affichage numérique
LL Verrouillage Clavier (Validations Via HART)
LS Activation MA+ME possible
LO uniq Activation MA possible
LA Clavier LA verrouilléL Protection en écriture
C Fonctionnement En Courant Constant
15 Affichage de la communication14 Valeur limite sup dépassée13 Signe pour valeur mesurée12 Valeur limite inf non atteinte
11 Mode/ Verrouillage Clavier
9 Unité/Bargraphe8 Valeur Mesure
7 Touche Décrémentation
6 Touche Incrémentation
5 Touche Mode
4 Connecteur test pour ampèremètre continu3 (-)Energie auxiliaire2 (+)Energie auxiliaire1 Connexion blindage
Légende 1-15
4)
1)
DM=Début Mesure FM=Fin Mesure
enregistrer valeur
Commande
M7 Etalonnage point zéro1)2)4)
M6 Réglage en aveugle FM1)2)4)
M5 Réglage en aveugle DM1)2)4)
M4 Réglage atténuation1)2)4)
M3 Définir et régler FM1)2)4)
M2 Définir et régler DM1)2)4)
Mode affichage en mA % pression
définir valeur/modifier valeur
Commande
M14 mA % unité1)2)4)
M13 mA % affichage valeur mesure1)2)
M10 Verrouillage clavier, protection en ecriture1)2)
M9 Courant défaut sup./inf.1)2)4)
M8 Générateur courant, u. 2s2)3)
3)
2)
, quitter sans enregistrer
1411
16 bar
18
18 bar
20 mA
20 mA
16 bar
20 mA184
20
4
20
4
0
14bar-2bar11 bar-2bar * 1 6 m A + 4 m A = 1 6 m AI =
Condition : voir les instructions de service Chapitre 6.
Définir début et fin de mesure
CalculerCourantSortie(p.ex.11 bar)
Définir finde Mesure(p. ex. 14 bar)
Définir Début deMesure(p. ex. 2 bar)
Situationde départ
et maintenir appuyés pendant 2 s pour la calibration à 20 mA.
Appliquer la pression correspondant au DMau transmetteur.
et maintenir appuyés pendant 2 s pour la calibration à 4 mA.
Définir début mesure :Choisir mode 02
Noter : les touches de commande peuvent être verrouillées ! Désactivation du verrouillage du clavier, voir -3-.
Appliquer la pression correspondant à la FM au transmetteur.
Définir fin mesure :Choisir mode 03
Appliquer la pression de référence.Raccorder l'ampèremètre continu (recommandé).
Réglalge du courant selon la formule de calcul disponible dans les instructions de service, chapitre 6.
Définir début mesure :Choisir mode 02
Ajuster à l'aide des touches et (réglage dynamique) et enregistrer le DM avec la touche .
Ajuster à l'aide des touches et (réglage dynamique) et enregistrer la FM avec la touche .
Avec et (2s) régler la fin de mesure ou limite supérieure du capteur et enregistrer avec .
Définir fin mesure en "Aveugle" :Choisir mode 06
Avec et (2s) régler le début de mesure ou limite inférieure du capteur et enregistrer avec .
Définir début mesure en "Aveugle" : Choisir mode 05
Avec et régler la pression correspondant à la FM (réglage dynamique) et enregistrer avec .
Régler fin mesure en "aveugle" :Choisir mode 06
Avec et , régler la pression correspondant au DM (réglage dynamique) et enregistrer avec .
Régler début mesure en "Aveugle" : Choisir mode 05
enregister avec
définir le point zéro avec et
Etalonnage point zéro:Choisir mode 07
Purger le transmetteur ou régler une pression référence connue (pression absolue <0,1 ‰ de etendue mesure).
Voir instructions service et certificats conformité!http://www.siemens.com/sitransp
Données Ex
HW: xx.yy.zzFW: aa.bb.cc
Figurent sur plaque homologation.
Code FW/HW Connexion transmetteur
(4) Charge(3) Energie auxiliaire UH
(2B) Blindage sur presse-étoupe
(2A) Connexion de blindage pour presse-étoupe en plastique
(1) Bornes de connexion
Régler fin mesure :Choisir mode 03
Leporello(- 2 -)(- 3 -)
2
3
1
Mode
UP
ZERO
SPAN
MODE
765
DOWN
15
141312
11 9
8
D
C
B
A
UP DOWNMODE UP DOWN
MODE
(3) (4)
(2B)
(2A)(1)
UP DOWN
UP DOWN
UP DOWN
UP DOWN
UP DOWN
UP DOWN
MODE
MODE
MODE
MODE
UP DOWN
UP DOWN
MODE
UP DOWNMODE
4
MODE
M11 Régler courbe caractéristique ("Lin")1)2)4)
SITRANSP300 mit HARTKurzanleitung (Leporello)A5E34318018-01, 03/2014
Vor der Installation und der Inbetriebnahme ist die Betriebsanleitung zu beachten!
Mit oder MA einstellen(Verstelldynamik)und mit MA speichern
Mit oder MA einstellen (Verstelldynamik)und mit MA speichern
drücken,Wert speichern
drücken, Wert speichern
mit und (2s) das Messendeauf das obere Sensorlimit setzen
Messende "blind" setzen:Modus 06 wählen
mit und (2s) den Messanfangauf das untere Sensorlimit setzen
Messanfang "blind" setzen:Modus 05 wählen
drücken, Wert speichern
mit oder den Druck einstellen, der ME entsprechen soll (Verstelldynamik)
Messend "blind" einstellen:Modus 06 wählen
drücken, Wert speichernMODE
mit oder den Druck einstellen, der MA entsprechen soll(Verstelldynamik)
Messanfang "blind" einstellen:Modus 05 wählen
drücken, Wert speichern
den Nullpunkt setzen.mit und
Nullpunkt abgleich:Modus 07 wählen
Messumformer belüften oder bekannten Referenzdruck einstellen. (Absolutdruck < 0,1 ‰ der Messspanne.)
siehe Betriebsanleitung und Konformitätsbescheinigungen!http://www.siemens.com/sitransp
Ex-Daten
sind auf dem Zulassungsschild abzulesen.
FW/HW-Kennzeichen Messumformer anschließen
(4) Bürde(3) Hilfsenergie UH
(2B) Schirm auf Kabelverschraubung
(2A) Schirmauflage bei Kunststoffkabel- verschraubung
(1) Anschlussklemmen
Messende einstellen:Modus 03 wählen
M11 Kennlinie einstellen ("Lin")1)2)4)
SITRANS P300 with HARTQuick Start Guide (Leporello)A5E34318018-01, 03/2014
Please refer to the Operating Instructions prior to installation and start up!
!
Leporello(- 2 -)(- 3 -)
2
4
3
1
Connection Box
2
4
3
1
UP DOWN
ZERO
SPAN
Mode 5 sRead-only OFFKeyboard disable
MODE
765
Keyboard(setting without display)
15
141312
11 9
8
Digital display
able only via HART)LL Keyboard disable (en-LS MA + ME can be setLO Only MA can be setLA Keyboard disabledL Read-onlyC Constant current mode
(15) Communication display(14) Violation of higher limit(13) Symbol for measured value(12) Violation of lower limit
(11) Mode/button lock(9) Unit/bar graph(8) Measured value(7) Decrement key(6) Increment key(5) Mode key(4) Test plug for external DC ammeter(3) (-) power supply(2) (+) power supply(1) shield support
Legend 1-15MA = zero point ME = limit point
4)
1)
1) 2) 4)
1) 2) 4)
1) 2) 4)
1) 2) 4)
1) 2) 4)
1) 2) 4)
M7 Zero adjustmentM6 Adjust ME without pressureM5 Adjust MA without pressureM4 Adjust dampingM3 Set and adjust MEM2 Set and adjust MADisplay mode in mA % pressure
Operation
Save valueMODE/ Change valueUP DOWN
1) 2) 4)
1) 2)
1) 2)
1) 2) 4)
M14 mA % dimensionM13 mA % measuring mode
M10 Keyboard disabling, read-onlyM9 Fault current upper/lowerM8 Current transm., and for 2 s2)3)
or change valueUP DOWN
Operation
3)
2)
,exit without savingMODE
r
Prerequisite: see Operating Instructions Section 6
scale and full scaleSetting start of
Calculating output current (p. e. 11 bar)D
(p. e. 14 bar)scaleSetting fullC
(p. e. 2 bar)of scaleSetting startB
situationInitialA
14 bar - 2 bar11 bar - 2 barI = * 16 mA + 4 mA = 16 mA
11 14
16 bar
18
18 ba
20 mA
20 mA
16 bar
4 18 20 mA
0 2
4
0 2
4
0
r
and press and hold for 2 s to set ME to 20 mA
UP DOWN
Apply reference pressureConnect DC ammete
and press and hold for 2 sto set MA to 4 mA
UP DOWN
Setting start of scale:Select mode 02
Note: the keys may be disabled!Remove key board disablingSee page -3-.
Apply pressure corresponding to ME tothe transmitter.
Setting full scale:Select mode 03
Adjust MA using and (variablespeed) and save ME using
Apply reference pressureConnect DC ammeter (recommended)
Adjusting full scale:Select mode 03
Apply reference pressure.Connect DC ammeter (recommended)
Adjust current according tocalculation formula,seeOperating Instructions, Section 6
Adjusting start of scaleSelect mode 02
Adjust MA using and (variablespeed) and save MA using
Set full-scale value to the upper sensor limit using and (2 s).Press to save value.
Setting full scalewithout application of pressure:
Select mode 06
Set start-of-scale value or the lower sensorlimit using and (2 s).Press to save value.
Setting start of scalewithout application of pressure:
Select mode 05Adjust pressure which is to correspond to MA using and (variable speed) Press to save value
Adjust pressure which is to correspond to ME using and (variable speed). Press to save value.
Adjusting full scalewithout application of pressure:
Select mode 06
Adjusting start of scalewithout application of pressure:
Select mode 05Zero point adjustment:
Select mode 07
See Instruction Manual and conformity certificates!http://www.siemens.com/sitransp
Ex Data
Can be read from the approval label
FW/HW releases Connecting the transmitter
(4) Load(3) Auxiliary power UH
(2B) Shield on cable gland
(2A) Shield support with plastic cable gland
(1) Supply terminals
MODEUP DOWN
MODEUP DOWN
MODEUP DOWN
MODEUP DOWN
MODEUP DOWN
MODE
MODE
UP DOWN
UP DOWNSet Zero using andPress to save value.
HW: xx.yy.zzFW: aa.bb.cc
HW: xx.yy.zzFW: aa.bb.cc
Vent transmitter (pressure, differential ressure, flow, level) or evacuate (absolute presssure <0.1 ‰ of span)
M11 Adjust characteristic ("Lin")1)2)4)
Leporello(- 2 -)(- 3 -)
2
3
1
Mode
UP
ZERO
SPAN
MODE
765
DOWN
15
141312
11 9
8
D
C
B
A
UP DOWNMODE UP DOWN
MODE
(3) (4)
(2B)
(2A)(1)
–+
(3) (4)
(2B)
(2A)(1)
UP DOWN
UP DOWN
UP DOWN
UP DOWN
MODE
UP DOWN
MODE
MODE
UP DOWN
MODE
UP DOWN
UP DOWN
MODE
UP DOWN
MODE
4
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 -
- 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 -
(1) Terminais de liga ão(2A) Blindagem união
(2B) Blindagem na união
(3) Energia auxiliar UH(4) Carga
ç
roscada de plásticopara cabos
roscada para cabos
Ligar o transmissorde pressão
Identificação FW/HWpodem ser consultados na placade homologação:
Dados Exver manual de instruções edeclaração de conformidade!http://www.siemens.com/sitransp
Ventilar o de pressãoou ajustar a pressão de referênciaconhecida.(Pressão absoluta < 0,1 ‰do fim de escala.)
transmissor
Equalização do zero:Seleccionar o modo 07
com eUP DOWNconfigurar o ponto zero.
MODE pressionar, memorizar valor
Ajustar o inícioda medição :
Seleccionar o modo 05“blind”
com ouUP DOWN, ajustar a pressãoque deve corresponder ao MA(dinâmica de ajuste)
MODE pressionar, memorizar valor
Ajustar o fimda medição :
Seleccionar o modo 06“blind”
MODE pressionar, memorizar valor
Configurar o inícioda medição “blind”:
Seleccionar o modo 05com e (2 segundos), configuraro início da medição para o limite inferiordo sensor
UP DOWN
Configurar o fimda medição
Seleccionar o modo 06“blind”:
com eUP DOWN (2 s) (2 segundos),configurar o fim da medição para o limitesuperior do sensor
MODE pressionar, memorizar valor
MODE pressionar, memorizar valor
com ou ajustar MA(dinâmica de ajuste)
UP DOWN
e com memorizar MAMODE
com ou ajustar MA(dinâmica de ajuste)
UP DOWN
e com memorizar MAMODE
Ajustar o início da medição:Seleccionar o modo 02
corrente a ser ajustada de acordocom a fórmula de cálculo, vermanual de instruções, capítulo 6
Criar a pressão de referênciaLigar o aparelho de medição dacorrente contínua (recomendado)
Ajustar o fim da medição:Seleccionar o modo 03
Criar a pressão de referênciaLigar o aparelho de medição dacorrente contínua (recomendado)
Configurar o fim da medição:Seleccionar o modo 03
Indicar a pressão que correspondeao ME no de pressãotransmissor
Nota: Os botões de comando podemser bloqueados! Suspender o bloqueiodos botões, ver página -3-.
e, assim, configurar ME para 20 mA
Configurar inícioda medição:
Seleccionar o modo 02
e, assim, configurar MA para 4 mAUP DOWNou premir por 2 segundos
Indicar a pressão que correspondeao MA no transmissor de pressão
UP DOWNou premir por 2 segundos
A Situaçãode partida
B Configurarinício damedição(p.ex. 2 bar)
C Configurarinício damedição(p.ex. 14 bar)
D Calcular a corrente de saída (p.ex. 11 bar)
Configurar o inícioe o fim da medição
Condição: ver manual de instruções,capítulo 6
I = * 16 mA + 4 mA = 16 mA11 bar - 2 bar14 bar - 2 bar
0
4
0 2
4
0 2
4 18 20 mA
16 bar
20 mA
20 mA
18 bar
18
16 bar
11 14
MODE, Finalizar sem memorizar2)
3)
M8 Produtor de corrente, e 2 s
M9 Corrente de avaria cima/baixo
M10 Bloqueio botões, protecção escrita
M13 mA % indicação tipo de medição
M14 mA % unidade
2) 3)
1) 2) 4)
1) 2)
1) 2)
1) 2) 4)
Operação
UP DOWNou alterar valorUP DOWN/ Configurar valor
Modo de indicação em mA % pressão
M2 configurar e ajustar MA
M3 configurar e ajustar ME
M4 ajustar amortecimento
M5 ajustar MA blind
M6 ajustar ME blind
M7 Equalização do ponto zero
1) 2) 4)
1) 2) 4)
1) 2) 4)
1) 2 ) 4)
1) 2 ) 4)
1) 2) 4)
Operação
MODE Memorizar valor
MA=Início da medição ME=Fim da medição
1)
4)
Legenda 1-151 Blindagem2 (+) Energia auxiliar3 (-) Energia auxiliar4 Ficha de teste para aparelho de medição
externo para corrente contínua5 Botão Mode6 Botão para
aumentar7 Botão para
diminuir8 Valor de medição9 Einheit/Bargraf
11 Unidade/gráfico bar
12 Valor limite inferior não alcançado13 Sinal para o valor de medição14 Valor limite superior ultrapassado15 Indicação da comunicação
C Operação constantede corrente
L Protecção contra escritaLA Botões bloqueadosLO Só MA pode ser
configuradoLS MA + ME podem ser
configuradosLL Bloqueio dos botões
(autorização apenasatravés de HART)
Mostrador digital8
911
121314
15
Botões(operação sem display)
5 67
MODE
Bloqueio dos botões,protecção contraescrita DES
5 sMode
SPAN
ZERO
UP DOWN
1
3
4
2
Espaço de liga ãoç(- 3 -)(- 2 -)
Leporello
!
SITRANSP300 com HARTInstruções abreviadas (Leporello)A5E34318018-01, 03/2014
Antes da instalação e colo-cação em funcionamento,é necessário respeitaro manual de instruções!
com ouUP DOWN, ajustar a pressãoque deve corresponder ao ME(dinâmica de ajuste)
–+
(3) (4)
(2B)
(2A)(1)
HW: xx.yy.zzFW: aa.bb.cc
M11 Ajustar curva caraterística ("Lin")1)2)4)
–+
SITRANSP300 con HARTInstrucciones abreviadas (Leporello)A5E34318018-01, 03/2014
Antes de la instalación y puesta en marcha deben leerse las instrucciones de servicio.
!
o
Establecer presión de referencia Conectar dispositivo de medición de corriente continua (recomendado)
Espacio de conexión
5 s Bloqueo del teclado, protección contra escritura OFF
Teclado(manejo sin pantalla)
Visualizador digital
LL Bloqueo del teclado (habilitación vía HART)
LS MA + FM aplicableLO solo PM aplicableLA Teclado bloqueadoL Protecc. contra escrit.C Servicio corr. const.
15 Indicador de comunicación14 Valor límite superior rebasado por exceso13 Signo para valor medido12 Valor límite inferior rebasado por defecto
11 Modo/ Bloqueo del teclado
9 Unidad/Bargraf8 Valor medido7 Tecla de decremento6 Tecla de incremento5 Tecla de modo
4 Conector de test para dispositivo externo de medición de corriente continua
3 (-) Energía auxiliar2 (+) Energía auxiliar1 Conexión de pantallas
Leyenda 1-15
4)
1)
PM = principio de medición FM = fin de medición
Guardar valor
Manejo
M7 Corrección del cero1)2)4)
M6 Ajustar FM a ciegas1)2)4)
M5 Ajustar PM a ciegas1)2)4)
M4 Ajustar atenuación1)2)4)
M3 Establecer y ajustar FM1)2)4)
M2 Establecer y ajustar PM1)2)4)
Modo de visualización en mA % pres.
Establecer valor/Cambiar valor
Manejo
M14 mA % unidad1)2)4)
M13 mA % Indicador de valor medido1)2)
Bloqueo del teclado,protección contra escritura1)2)
M9 Corriente de defecto arriba/abajo1)2)4)
M8 Sensor de corriente, y 2s2)3)
3)
2)
, salir sin guardar
1411
16 bar
18
18 bar
20 mA
20 mA
16 bar
20 mA184
20
4
20
4
0
14 bar - 2 bar11 bar - 2 bar *16 mA + 4 mA = 16 mAI =
Requisitos: consulte el capítulo 6 de las instrucciones de servicio.
Establecer principio y fin de medición
Calcular intensidad de salida (p. ej. 11 bar)
Establecerfin de medición(p. ej. 14 bar)
Establecerprincipio de medición(p. ej. 2 bar)
Situaciónde partida
UP y DOWN mantener pulsado 2 sy con ello establecer FM a 20 mA
Dar al transductor de medida la presión que equivale al PMUP y DOWN mantener pulsado 2 s y con ello establecer PM a 4 mA
Establecer principio de medición: elegir modo 02
Nota: es posible que las teclas de manejo estén bloqueadas. Quitar el bloqueo del teclado, consulte la pág. -3-.
Dar al transductor de medidala presión que equivale al FM
Establecer fin de medición:elegir modo 03
Establecer presión de referencia Conectar dispositivo de medición de corriente continua (recomendado)
Intensidad que debe ajustarse según la fórmula de cálculo, consulte el capítulo 6 de las instrucciones de servicio
Ajustar principio de medición: elegir modo 02
Ajustar PM con UP o DOWN(dinámica de ajuste)y guardar con MODE PM
y guardar con MODE PM
Ajustar PM con UP o DOWN (dinámica de ajuste)
pulsar, guardar valor
pulsar, guardar valor
Establecer el fin de la medición con UP y DOWN (2 s) al límite superior del sensor
Establecer el fin de la medición "a ciegas":
elegir modo 06
Establecer el principio de la medición con UP y DOWN (2 s) al límite inferior del sensor
Establecer principio de medición "a ciegas":
elegir modo 05
pulsar, guardar valor
con o ajustar la presión que debe equivaler al FM (dinámica de ajuste)
Ajustar el fin de la medición "a ciegas": elegir modo 06
pulsar, guardar valorMODO
con UP o DOWN ajustar la presión que debe equivaler al PM (dinámica de ajuste)
Ajustar el principio de la medición "a ciegas":
elegir modo 05
pulsar, guardar valor
establecer punto cero.con y
Corrección del cero:elegir modo 07
Ventilar transductor de medida o ajustar presión de referencia conocida. (presión absoluta<0,1 ‰ del alcance de medida)
consulte las instrucciones de servicio y los certificados de conformidad.http://www.siemens.com/sitransp
Datos Ex
HW: xx.yy.zzFW: aa.bb.cc
se encuentran en la placa de homologación.
Identificador FW/HW Conectar transductor de medida
(4) Carga(3) Energía auxiliar UH
(2B) Pantalla en pasacables
(2A) Conexión de pantallas para pasacables de plástico
(1) Bornes de conexión
Ajustar fin de medición:elegir modo 03
M10
Leporello(- 2 -)(- 3 -)
2
3
1
Mode
UP
ZERO
SPAN
MODE
765
DOWN
15
141312
11 9
8
D
C
B
A
UP DOWNMODE UP DOWN
MODE
(3) (4)
(2B)
(2A)(1)
MODE
MODE
UP DOWN
MODE
UP DOWN
MODE
4
M11 Ajustar curva característica ("Lin")1)2)4)
–+
SITRANSP300 con HARTBreve introduzione (Leporello)A5E34318018-01, 03/2014
Prima dell'installazionee della messa in servizioosservare le istruzioni operative!
!
oppure
Impostare pressione di riferimento collegare amperometro di corrente continua (consigliato)
Vano di collegamento
5 s Blocco tastiera, protezione antiscrittura OFF
Tastiera(comando senza display)
Indicatore digitale
LL Blocco tastiera (abi- litazione solo tramite HART)
LS MA + ME impostabiliLO solo MA impostabileLA Tastiera bloccataL Protezione antiscritturaC Servizio a corrente costante
15 Indicazione di comunicazione14 Valore limite superiore superato13 Segno per valore di misura12 Valore limite inferiore superato
11 Modo/ Blocco tasti
9 Unità/Indicatore a barre
8 Valore di misura7 Tasto Decremento6 Tasto Incremento5 Tasto Modo
4 Connettore di prova per amperometro di corrente continua
3 (-) Energia ausiliaria2 (+) Energia ausiliaria1 Supporto schermo
Legenda 1-15
4)
1)
MA= inizio misurazione ME= fine misurazione
Memorizzare valore
Comando
M7 Calibrazione punto zero1)2)4)
M 6 Regolazione cieca ME1)2)4)
M 5 Regolazione cieca MA1)2)4)
M 4 Regolazione smorzamento1)2)4)
M 3 Regolare e impostare ME1)2)4)
M 2 Regolare e impostare MA1)2)4)
Modo visualizzazione in mA % Pressione
Impostazione valore/Modifica valore
Comando
M 14 mA % Unità1)2)4)
M 13 mA % Indicazione modalità di misura1)2)
M 10 Blocco tasti, Protezione antiscrittura1)2)
M 9 Corrente di guasto superiore/inferiore1)2)4)
M 8 Trasmettitore di corrente, e 2 s2)3)
3)
2)
1411
16bar
18
18bar
20mA
20mA
16bar
20mA184
20
4
20
4
0
14bar-2bar11 bar-2bar * 1 6 m A + 4 m A = 1 6 m AI =
Presupposto: vedere Istruzione operative Capitolo 6.
Imposta Inizio Misurazione e Fine Misurazione
Regolazione corrente di uscita (ad es. 11 bar)
Impostazionefine misurazione(ad es. 14 bar)
Impostazioneinizio misurazione(ad es. 2 bar)
Situzionedi partenza
e tenere premuto 2 sper impostare ME a 20 mA
Immettere la pressione corrispondente a MA nel trasmettitore
e tenere premuto 2 sper impostare MA a 4 mA
Impostare inizio misurazione:Selezionare il modo 02
Avvertenza: I tasti di comando potrebberoessere bloccati. Disattivare blocco tastiera vedere Pagina 3.
Assegnare pressione corrispondente a ME sul trasmettitore
Impostare fine misurazione:Selezionare il modo 03
Impostare pressione di riferimento collegare amperometro di corrente continua (consigliato)
Corrente da regolare secondo formula di calcolo vedere Istruzioni operative Capitolo 6.
Regolazione inizio misurazione:Selezionare il modo 02
Regolazione con oppure MA(dinamica di regolazione)e salvare con MA
e salvare con MA
Regolare con o MA(dinamica di regolazione)
tenere premuto, salvataggio del valore
tenere premuto, salvataggio del valore
con e (2s) la fine misurazione regolazione al limite superiore del sensore
Impostazione"cieca"fine misurazione:
Selezionare il modo 06
con e (2s) l'inizio misurazione regolazione al limite inferiore del sensore
Impostazione"cieca"inizio misurazione:
Selezionare il modo 05
tenere premuto, salvataggio del valore
con o regolare la pressione, che deve corrispondere a ME (dinamica di regolazione)
Regolazione"cieca"fine misurazione:
Selezionare il modo 06
tenere premuto, salvataggio del valore
MODE
con o regolare la pressione, che deve corrispondere a ME(dinamica di regolazione)
Regolazione"cieca"inizio misurazione:
Selezionare il modo 05
tenere premuto, salvataggio del valore
impostazione del punto di zero.con e
Calibrazione del punto di zero:Selezionare il modo 07
Ventilare il trasmettitore o regolare la pressione di riferimento nota. (Pressione assoluta<0,1 ‰ del campo di misurazione).
vedere le Istruzioni operative e le dichiarazioni di conformitàhttp://www.siemens.com/sitransp
Dati Ex
HW: xx.yy.zzFW: aa.bb.cc
si trovano sulla targhetta di omologazione.
Marcatura FW/HW Collegamento del trasmettitore
(4) Carico(3) Energia ausiliaria UH
(2B) Schermo su pressacavo
(2A) Supporto schermo con pressacavo in plastica
(1) Morsetti di collegamento
Regolazione di fine misurazione:Selezionare il modo 03