-
co co 0 I.{)
0 0 0 N
0 CY)
Lot 3 DP789406
'C2"J
2600
0 N (J)
site plan
proposed shed
Unisex han icapped toilet to AS1428.1
Connect to existing water and sewer seNices
detail : floor plan - amenities Scale 1: 100
amenities - see detail
'"O Q)
�l====::::i
cii :s:
cii
Q)
0 0 'Sj'" N
12mm Craftwood roof 95x36 Hyspan joists @ 600c/c AC wall and
ceiling sheeting 90x35 timber wall framing - fixed to
existing floor
� �:::::::==�=l
floor of shed floor
section A-A
Sheet Size A3
Drawn
J.Babbs
Checked B.Allsworth
�1'1r� D��fE@1'1f 10 Jasmin Court, Corowa, NSW 2646
Mobile: 0428 573 024
Email: [email protected]
Proposed storage shed
UPTON ENTERPRISES' PTY. LTD. Lot 3 Headerworld Avenue,
COROWA
w
::::>
N 0
t--t--'r"
C0 L()
Sheet No. 1 of 1
Date 6 April, 2020
Scale 1: 500
Drawing No.
82012
z w
� 0
� 0
� w
0
w
I
-
�t21 )4��'?I � Address: PO BOX 5,
Avondale Heights, Vic 3034 EMERALD Phone: 0416 797 422
Date: 07/04/2020 Our Ref - 605083
DESIGN 6 CONSTRUCTION
RE: Structural Certification of Shed For Paul Upton
To whom it may concern
Email: [email protected]
The purpose of this letter is to provide structural
certification over the aspects of the buildings mentioned above,
namely
• Steel Framed Shed
The drawings referenced in this certification are
605083 pages 1 to 9 (07/04/2020) Engineering Schedule page 1
(07/04/2020)
I have relied on the following reference documents
• AS 1170.0 General Principals (2002)• AS 1170.1 Permanent &
Other Actions (2002)• AS 1170.4 Earthquake Loads (2007)• AS 4100
Steel Structures Code (1998) • AS 4600 Cold Formed Section Code
(2005) • Building Code of Australia Volume 1 & 2 (as
applicable)
o Clause C1 .11 and Specification C1 .11 of the BCA 2015
Yours faithfully,
Camilo Pineda Moreno BPB 2769
-
ENGINEERING SCHEDULE
CERTIFIED STEEL PORTAL FRAME SHED DESIGN FOR "REGION A" TERRAIN
CATEGORY 2.0, 2.5 & 3.0 - IMPORTANCE LEVEL 2. Internal
Pressure: 0.7 Design Snow Load: 0.00 KPa, Roof Snow Load: 0.00
KPa
Customer: Paul Upton Site Address: 2 Header World Ave, Corowa
NSW 2646
Main Building: Span: 12, Length: 36, Height: 5, Roof Pitch: 11
degrees The length being comprised of 6 bays, the largest bay is 6m
bays. Left LeanTo: NA Right LeanTo: NA
INTERNAL PORTALS
Column: 2C25024 Rafter: 2C25024
Knee Brace: 2C15015 Knee Brace Length: 2600
Apex Brace: 2C15015 Apex Brace Length: 5400
LEFT LEAN TO PORTALS
Internal Column: NA Internal Rafter: NA
End Column: NA End Rafter: NA
Knee Brace: NA Knee Brace Length: NA
END PORTALS
Column: C25024 Rafter: C25024
Knee Brace: NA Knee Brace Length: NA
Apex Brace: NA Apex Brace Length: NA
Endwall Mullion: C25024
RIGHT LEAN TO PORTALS
Internal Column: NA Internal Rafter: NA
End Column: NA End Rafter: NA
Knee Brace: NA Knee Brace Length: NA
NOTE: All unclad intermediate columns are always back to back
(refer to drawing: Floor Plan).
Eave Purlin: TH120100 Side Wall Girts: TH120100
Front End Wall Girts: TH120100 Back End Wall Girts: TH120100
Roof Purlins: TH120100
PURUNS AND GIRTS
NOTE: Girt spacing will vary to a maximum 1.1 m where window/s
are located.
FASTENERS
Sleeve Anchor Bolts: M16x105 Sleeve Anchor Frame Bolts: M16x45
Purlin Assembly Zinc (Mild)
Frame Screws: Frame Screw 14x14x22 Cross Bracing Strap: 32mm x
1.2 strap
Open Bay Header Height: NA
151 Smeaton Grange Road,
Max Spacing: 1100 Max Spacing: 1100 Max Spacing: 1100 Max
Spacing: 1000
Overlap: 10% Overlap: 10% Overlap: 10% Overlap: 10%
CIVIL & STRUCTURAL ENGINEERS
DOMESTIC & LIGHT INDUSTRIAL STEEL PORTAL FRAME SHED
STRUCTURES This structure is designed in compliance with AS4600,
AS3600 and AS1170 1 to 4 as Importance Level 2 with a Live Load of
0.25kPa as "Air Leaky Structures" providing stability when openings
are prevalent.
The structures are clad with corrugated pre-painted finish,
0.42mm walls and 0.42mm roof (compliant with AS1562.1 Metal) over
cold formed 450 to 550mPa galvanized steel C sections primary
frames.
Primary framing is fastened together with 4.6 Class galvanized
bolts adequately tensioned on ground prior to erection.
Secondary framing steel bracing, with purlins and girts lapped,
are all tek fastened to primary steel with a minimum of two (2)
teks per connection as specified in details.
All rainwater products are compliant with AS2179.1 (Metal).
ENGINEERING The undersigning engineer has checked that the
design of the structure complies with relevant current Australian
Standards as stated above and the following i.e AS4671- 2001 Steel
Reinforcing materials, AS3600 - Concrete structures. However, he
will not be present during construction, neither will he conduct
inspections nor construction supervision.
The class 1 0a buildings are designed for erection on pad
footings or slab based on soil of classification "A"-"P" with
minimum bearing capacity 100kPa (i.e. organic soil is to be removed
to a suitable material below natural surface).
Where (suitable) fill is required to level the site, it should
be placed and compacted in layers of 150mm maximum.
Concrete pad footings and slab supply and placement is to be in
compliance with AS2870-2011 Residential Slabs & Footings,
AS3600-2009 Concrete Structures for A2 and 82 exposure (i.e. 25mPa
strength @ 28 days strength) with recommended slump 75 to 80mm for
light pneumatic tyred traffic all trafficable floors.
For sites where these conditions are considered to be
inadequate, a customized foundation design for the structure can be
supplied to suit a specific purpose.
CONSTRUCTION Erection of the structure is to be in compliance
with local and state ordinances,
Occupational Health and Safety Regulations and with plans
provided.
GENERAL The designs as portrayed on the drawings remain the.
intellectual property of Best Sheds Ply Ltd and are provided for
building approval and construction purposes only and are only valid
when blue ink signed and dated by the engineer.
SNOW LOAD Following conditions only apply to buildings with snow
loading: • No maintenance or roof traffic permitted on the roof
while there is snow present. • No other structure to be erected
within 500mm of the gutters of this building.
COMPONENT DIAGRAM
TYP. = TYPICAL U.N.O. = UNLESS NOTED OTHERWISE
Customer Name: Paul Upton DATE 07-04-2020
ErsSs• Smeaton Grande, NSW, 2567
COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING Site Address: 2 Header World Ave JOB NO. 605083
ds Phone: 02 4648 7777 Corowa, SHEET 1 of 9 Fax: 02 4648
7700
EMERALD CAMILO PINEDA MORENO
�..g,. / /4._ NSW, 2646
1/al,te & 2@«tff_ Vitiea ta 'Jt.oa Email:
[email protected] Bend MIEAust RPEng Signature: Date:
?.!.·?�:.2..°.�.°. ...... - OES!GIJ & CONSIBUCTIO:I RPEO 15562
TBP RC41817 {VIC) I
-
�s• ds
'tlat@ & 2,,"®t V&u:d w 'lfo,, -
(0 (0 � (0
151 Smeaton Grange Road, Smeaton Grande, NSW, 2567 Phone: 02
4648 7777 Fax: 02 4648 7700 Email: [email protected]
36000
ED LEFT ELEVATION
SCALE: 1 :125
36000
CD RIGHT ELEVATION
SCALE: 1: 125
ECIVIL & STRUCTURAL ENGINEERS
COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING
� EMERALD
CAMILO PINEDA MORENO Bend MJEAust RPEng Signature: �'
DESIGN & CONSTRUCTIO/J RPEQ 15562 TBP RC41817 {VIC) I
0 0 N
... 0
-f 820 f---
Customer Name: Paul Upton Site Address: 2 Header World Ave
Corowa,
Date °.7..:°..�:.2..°.�.°. ..... NSW, 2646
. I
. I
(0 (0 � (0
DATE JOB NO. SHEET
07-04-2020 605083 2 of 9
-
151 Smeaton Grange Road,
rsSsiSmeaton Grande, NSW, 2567
ds Phone: 02 4648 7777 Fax: 02 4648 7700
Va&,e & :2«atil,r, V
-
rsSs• ds 1/at«e & :Z«a!itq Vwxt t 'J/_M
0 (D 0)
0 (D 0)
0 (D 0)
-
---
I
gl (7') I_J_ 0 (D 0)
+f-1430--I-
0 0 N
-
(D (D � (D
I:
-0 (D 0)
+--------
0
0)
-+--------
0
en
-I---
0 (D en
I---
0 0
6000
' "'-
-/ /
151 Smeaton Grange Road, Smeaton Grande, NSW, 2567 Phone: 02
4648 7777 Fax: 02 4648 7700 Email: [email protected]
"
/
"
II
II
II
II II
71
I.
/
/ /
/
X
�
�
6000
-n
II
I I
l II 0 CD
0
gl(s)l N
II ft:1430--f- II
II 4000
"
6000 . I. 6000
ED LEFT ELEVATION
"
-·
/11 II
II
II II
'II "'
I I
SCALE: 1: 125
6000
"
K '
1 "'- "' " II II / II / II/ ,,,
I
::
'
II "'
"' '
II
II / II / II/ ,v
. I 36000
/11 /
/ II /., X II
� II � II
'II �,
6000 I 36000
ED RIGHT ELEVATION
SCALE: 1 : 125
CIVIL & STRUCTURAL ENGINEERS
:: ..
/11 /
II / /
X II � II
""' II
'II �
6000 . I.
6000
E COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING -.,� EMERALD CAMILO PINEDA MORENO Bend l,11EAust RPEng
Signature: ,,....; OESIG:J & CO/lSTRUCTION RPEO 15562 TBP
RC41817 {VIC)
/
0
00 N .,,-
4000
6000
"
II
II
II II II
II
I
Date: °.!:.?.�:.2..°.2..°.. .....
"
I� / ' ,
II "'- / "' /" ., II X
II / � II / � II.,.,
. I 6000 : I
�� --
II
II
II
II T 0 00 N
II j
I ----f 820 j-
6000 6000 -,
Customer Name: Paul Upton Site Address: 2 Header World Ave
Corowa, NSW, 2646
(D (D � (D
DATE 07-04-2020 JOB NO. 605083 SHEET 4 of 9
-
rsSs• 151 Smeaton Grange Road, Smeaton Grande, NSW, 2567
ds Phone: 02 4648 7777 Fax: 02 4648 7700
VaC@ & 2(((7.l'itff: Vcitea I' 'f/.o« Email:
[email protected] -
N 0)
N 0)
N 0
00) 0
N O>
N 4000 0)
0 0 N 12000
ED REAR ELEVATION
SCALE:
N 0)
N O>
N 0)
N"'
0 0
N
E EMERALD
DESIG!J & CONSTRUC1101l
1:125
0
00 ""
. 4000
12000
CIVIL & STRUCTURAL ENGINEERS
COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING
CAMILO PINEDA MORENO
Bend M/EAust RPEng RPEQ 15562 TBP RC41817 (VIC) Signature:
� /4 u �
I
0 0 0 U?
FRAME#7
0 0 0 U?
FRAME #1
-
FRAME LINE#--> 0
; _J _J
0
z
0 0 0 N
rsSs• ds
0
0
0
0
1/at«e & 2«att/'f. V&iea ta 'Jfoa -
6000
BAY#--> DJ
X-BRACING
!.J
[I]
B
DJ 0
fl X-BRACING
151 Smeaton Grange Road, Smeaton Grande, NSW, 2567 Phone: 02
4648 7777 Fax: 02 4648 7700 Email: [email protected]
0 6000 [I]
® m
frl
ED
36000 (SIDEWALL 'B')
0 6000 0 [I]
X-BRACING
lI1 ill
frl Jil X-BRACING
FLOOR PLAN
SCALE: 1:125
CIVIL & STRUCTURAL ENGINEERS
6000
GJ
CD
E COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING ,,,,--� EMERALD
CAMILO PINEDA MORENO Bend MIEAust RPEng
DES1Grl&CD1JSffiUCTlON RPEQ 15562 TBP RC41817 {VIC}
Signature: I
0 6000 0 6000 (I] w
® 0 ID I LJ
[J
0
[J
fil fil n
®
Customer Name: Paul Upton DATE 07-04-2020Site Address: 2 Header
World Ave JOB NO. 605083
Corowa, SHEET 6 of 9
Date: ?.!.:?.�:.2.?.2..? ...... NSW, 2646
-
FRAME LINE#--> 036000 (SIDEWALL 'B') 0
6000 0 6000 0 6000 0 6000 0 6000 0 6000 BAY#--> DJ 0 0 8J [}]
0
I I
'.'(
0
0
I I
CD ROOF FRAMING PLAN
SCALE: 1 :125
rsSs• 151 Smeaton Grange Road,
ECIVIL & STRUCTURAL ENGINEERS Customer Name: Paul Upton DATE
07-04-2020
Smeaton Grande, NSW, 2567 COMMERCIAL - INDUSTRIAL - RESIDENTIAL
- FORENSIC - STEEL DETAILING Site Address: 2 Header World Ave JOB
NO. 605083
ds Phone: 02 4648 7777 Corowa, SHEET 7 of 9 Fax: 02 4648
7700
EMERALD CAMILO PINEDA MORENO
/4 " , 1-i:_ NSW, 2646
Vaf«e & 2,,at«,, V
-
SLAB FOUNDATIONS DOMESTIC/ LIGHT INDUSTRIAL (100mm MINIMUM
CONRETE SLAB INCLUDED)
SOIL REINFORCING EDGE
EDGE BEAM CLASSIFICATION PIER (slab thickness
(COMPACTED) IN SLAB BEAM not included)
MESH TRENCH REINFORCING MESH
0X DEPTH DEPTH WIDTH
A, S, & M SL72 - 450 X 400 --M-D SL82 L11TM3 - 300
H TO H-D SL82 L 11TM3 - 400
E TO E-D SL82 L11TM4 -- 400 P (DROP EDGE BEAM OR STANDARD
EDGE
BEAM WITH PIERS SL82 L 11TM4 4500 400 UNDER COLUMNS
300 INTO FIRM GROUND)
THICKNESS: 100MM WITH MINIMUM 30MM COVER. REFER TO SLAB
FOUNDATION TABLE FOR REINFORCING SPECIFICATION
STRENGTH: 25mPa
2x M16 BOLTS
2 X 16MM DIA SLEEVE ANCHORS,
-
300
300
400
400
12MM DIA INTERNAL ROD-MIN 11 OMM LONG
I In. w 0
REFER TO SLAB TABLE FOR MESH TYPE - 30MM COVER
L\ . .
POLYTHENE WATERPROOF MEMBRANE ON CONSOLIDATED SUB-BASE SHOWN
DASHED
0
�
I. WIDTH 'I
y o INDICATES 16 mm0
BOLT
2C25024 FRAME COLUMN
DBL. 3 mm 11' HAUNCH BRACKET (SAME DEPTH
AS MEMBERS)
(2) 16 mm,i BOLTS AT EACH END OF KNEE
BRACE
SLAB DETAIL
2C25024 FRAME RAFTER
/------ 2C15015 KNEE BRACE, 2600 mm LONG (OMIT A ENDWALLS)
NOTE: ALL DOUBLE COMPONENTS SHALL BE SINGLE AT ENDWALLS.
A HAUNCH CONNECTION
151 Smeaton Grange Road,
rsSs• Smeaton Grande, NSW, 2567
ds Phone: 02 4648 7777 Fax: 02 4648 7700
Vat"e & 2@{iµ( Vmea t,, Jtott Email:
[email protected]
0 "'�
I.
z 2 :::,--' 0 o NOTE:
ENSURE EARTH/SOIL IS KEPT CLEAR OF WALL CLADDING AT ALL TIMES. .
.
z ALTERNATE PIER DETAIL
10GX 16MM SHEETING SCREW, REFER TO SCREW
SPACING DIAGRAM FOR FREQUENCY
TOPHAT 120 WALL GIRT WITH
10%MM MINIMUM
OVERLAP
0 l!) N 0 N
2X14G TEK SCREWS
D GIRT CONNECTION 2C25024 FRAME RAFTER
(2) 16 mm0 BOLTS AT EACH END OF APEX BRACE
DBL. 3 mm 11° APEX BRACKET, WITH (8) 16 mm0 BOLTS PER
BRACKET
8 X 14G TEK SCREWS
2C15015 APEX BRACE (OMIT AT ENDWALLS), 5400 mm LONG
NOTE: ALL DOUBLE COMPONENTS SHALL BE SINGLE AT ENDWALLS.
B APEX CONNECTION
H
12g x14 x 35mm LONG ROOF SCREWS
RIDGE PURLIN
v::vt---= = 1' = = = 1' = = ¢--:::', INTERMEDIATE PURLIN
-..4'-C, 1' = 1' = 1' = 1' = tf>v::::v EAVE PURLIN
0.42 BMT CORRUGATED ROOF SHEETING
ROOF SHEETING
2 x 14G TEK SCREWS ABOVE & BELOW IN SIDE OF PURLIN
-UNDERSIDE SCREW NOT VISIBLE IN DETAIL
2 x 14G TEK SCREWS ABOVE & BELOW IN SIDE OF PURUN
-UNDERSIDE SCREW NOT VISIBLE IN DETAIL
F
C
4 x 14G TEK SCREWS PER COLUMNUNDERSIDE SCREW NOT VISIBLE IN
DETAIL
TOP HAT CONNECTION
RAFTER/EAVE PURLIN
COLUMN
COLUMN ADJACENT TO ROLLER DOOR AFTER NOTCHED OUT
12x 14G TEK SCREWS
ENDWALL MULLION ROTATED
1 Og x 16mm LONG WALL SCREWS
WALL GIRT
� =,= =,= =,= =,= ,..,,,=✓
EAVE PURLIN
0.42 BMT CORRUGATED WALL SHEETING
TOPHAT 64
10GX 16MM SHEETING SCREW, REFER TO SCREW
SPACING DIAGRAM FOR FREQUENCY
TOPHAT 120
SHEETING
WALL SHEETING
12G X 35MM SHEETING SCREW, REFER TO SCREW SPACING DIAGRAM FOR
FREQUENCY
z 2 :::, --' 0 0
0 "' N
0 EAVE CONNECTION
D
TOPHAT 120 ROOF PURLIN WITH 10%
MINIMUM OVERLAP
12G X 35MM SHEETING SCREW, REFER TO SCREW SPACING DIAGRAM FOR
FREQUENCY
4X14G TEK SCREW
PURLIN CONNECTION
ECIVIL & STRUCTURAL ENGINEERS Customer Name: Paul. Upton
DATE 07-04-2020
COMMERCIAL - INDUSTRIAL - RESIDENTIAL - FORENSIC - STEEL
DETAILING Site Address: 2 Header World Ave JOB NO. 605083
Corowa, SHEET 8 of 9
EMERALD CAMILO PINEDA MORENO
/;;;,.de. , /� NSW, 2646 Bend MIEAust RPEng Signature:
Date:?!.:?.�:.�.°.�.� ...... DESIGN & CO/JSTRUCTIO/l RPEQ 15562
TBP RC41817 {VIC) /
-
END WALL
GIRT
2 x 14G TEK
SCREWS
END WALL GIRT
BRACKET
END WALL
COLUMN
END WALL GIRT
END WALL GIRT
BRACKET
N ENDWALL GIRT BRACKET
SLAB EDGE
j CORNER COLUMN BASE
151 Smeaton Grange Road, rsSsi Smeaton Grande, NSW, 2567 ds
Phone: 02 4648 7777 Fax: 02 4648 7700
1/ab
-
FEDERATION COUNCIL
APPLICATION FORM
(:) 100 Edward Street Corowa NSW 2646
8 PO Box 77, Corowa NSW 2646
$ (02) 6033 8999
® [email protected]
DEVELOPMENT APPLICATION/ CONSTRUCTION CERTIFICATE /COMPLYING
DEVELOPMENT/ PLUMBING Environmental Planning and Assessment Act
1979 and Local Government Act 1993
• Council will not accept incomplete applications. It is the
responsibility of the applicant to ensure the required information
is provided.
• Associated fees must be paid at the time of lodgment.
PRIVACY STATEMENT: Information provided to Council may comprise
personal information as defined under the Privacy and Personal
Information Protection Act
1998. Personal information may be utilised by the Council to
assess any application under the Environmental Planning and
Assessment Act 1979 and in accordance with other legislation.
Please note that personal information may also be made available to
third parties in accordance with the Government Information
(Public
Access) Act 2009.
TYPE OF APPLICATION
&15evelopment Application (DA) □ Construction Certificate
(CC}
□ Complying Development Certificate (CDC}
□ Plumbing Application (LGA)□ Manufactured Home (Section 68)
Have you attended a Pre DA Meeting with a Council Officer: �No □
Yes -If Yes, With Whom: __ _ _ _ _ _____ _
(If you ore installing a new septic system please complete the
Application to lnsto/1, Construct, Alter or Operate an O n -Site
Management System form)PROPOSED DEVELOPMENT
Please provide a detailed description of your proposal -
including details of the subdivision, the use of any buildings,
demolitions or tree removals.
/1/e cv color &t::?.,,,_ / r:/.-r2,r0r O Le e:>. State:
.A/ S tc/ Postcode: '2 6' '-f-6 •
Lot: '3 Section:__ ____ DP/SP: DP 7 g,-q tf-O b . Area Of Land:
CfO IL
Office Use Only
m2 ___ ___ ha
Date Documentation Received: ____________ _ Total Fees:$
______________ _
Receipt Number: _____________ _ Date Paid: _______________ _
Application Number: __________________________ _
CREATING OPPORTUNITY• 11 l
-
DEVELOPMENT DETAILS
Type of Development: ilef'Local
D Integrated
Proposed Development:
D Residential - Alterations & Additions D Demolition
D Deferred
D Staged
D Dual Occupancy/ Multi-Unit D Residential - Minor Structures
�ndustrial
D State Significant
D Designated
D Residential - Single Dwelling D Swimming Pool
D Commercial/ Retail/ Office D Subdivision D Subdividing a
building into strata units'
D Changing the use of land or a building, or the classification
of a building?
D Other: _ _____________ _
Is the proposed development located on contaminated land? D Yes
i>r'No _____________ _
Does the land contain and culturally significant or heritage
items? D Yes l;;,t No ______________ _
Current Use of Land: ____
/_,.,_�--l(_'-'f''-/_,_r'--,'----'�'---'-/ ___________________
_
NOTE: If you do not apply for demolition on this application,
and you need to demolish structures on the site, o separate
Development Application will need
to be submitted to, and approved by Council, prior to the
removal of any structures from the property.
TYPE OF CONSENT:
Is your proposal a Designated Development?
Is your development an Integrated Development?
(ff your application requires one or more approvals from
state agencies then your development is integrated.)
DYES- Please attach an Environmental Impact Statement (EIS) lirr
ALL Other Developments - Please attach a Statement of
Environmental
Effects (SEE)
!r"NO
0 YES
NOTE: An amount of $320may be applicable for some state agency
that will assess your proposal must be paid to Council upon
lodgment together with an additional copy of your application and
relevant documentation for each agency.
STAGED DEVELOPMENT
You can apply for development consent for part of your proposal
now and the remaining part(s) at a later stage.
Are you applying for development consent in stages? □ YES
,0"NO
If Yes, please attach: Information which describes the stages of
your development; Copy of any consents you already have for part of
your development.
CONSTRUCTION STATISTICS
This information is required by the Australian Bureau of
Statistics (ABS). The ABS uses this information as key economic
indicators for the
country. If there are two or more different material types to be
used, then please nominate the primary material type.
Is proposed building a: �New building
Value of development including GST:
D Alterations to existing D Additions to existing
Total floor area of development: 'f- 1 2 m2
Description of existing developments on land: __ £_--�-'�[_·
_/_,_ .... _.+"I ___ J._L_e_/ _ _ . _____ f:._)i_,--. __ k" __
/�Z'--_""'-__ _/
21/3/19 Version 2 -19/8532
� FEDERATION� COUNCIL
-
CONSTRUCTION STATISTICS
FLOOR FRAME WALLS ROOF
�Concrete or Slate D Timber D Brick Veneer D Curtain Glass □
Tiles
D Timber �teel □ Full Brick �teel _&i, Steel/Colourbond
□ Other D Aluminum D Concrete or Stone D Aluminum D Other
□ Not Applicable D Other D Fiber Cement D Other D Not
Applicable
□ Not Applicable D Timber □ Not Applicable
¥'
No. of existing dwellings on land which the new building is to
be erected: I
No. of dwellings to be demolished in connection to the new
building: 0
No. of Storeys: _____ / ___ _ No. Of Residential Units: _ _ O _
______ _ __
BUILDERS DETAILS
Name:
Licence Number: CtP � ___,__ e.r-£ � / A,f /I- □ Owner Builder
/
Address: -�/_7_��-C=--------=---M�r:__.c"""--· --'
-
REQUIRED DOCUMENTATION
Please provide Two (2) copies of all documentation excluding
application form unless indicated below. Plans are to be provided
in A3 size (drawn to scale). All plans must show North Point.
Larger
plans may be requested.
Develo�ment A��lications Construction Certificate Com�l'Jling
Develo�ment Plumbing A��lication
j)rl Locality Plan □ Locality Plan D Locality Plan □ Site
plan
(Sl;site Plan D Site Plan D Site Plan □ BASIX or BCA Section J
Report
�evations D Elevations D Elevations (where applicable) U Floor
Plan (existing and proposed works are shown separately)
□ BASIX or BCA Section J □ BASIX or BCA Section J □ BASIX or BCA
Section J D Hydraulic design Report Report Report (larger
commercial projects) (where applicable) (where applicable) (where
applicable) Floor Plan (existing and
D Floor Plan (existing and D Floor Plan (existing and proposed
works shown separately) proposed works shown proposed works
shown
separately} separately) f Statement of Sectional plans Sectional
plans (indicating
nvironmental (indicating detailed detailed Effects (2 copies)
construction) construction)
D Specifications D Specifications D Structural or Civil
D Structural or Civil Engineers design Engineers design
COPYRIGHT STATEMENT: 1. To the extent that the signatory to this
form is the copyright owner of documents lodged with this
application, you licence Council to make all
documents publicly available, and further licence Council to
reproduce and/or communicate all such documents for any purpose
associated with theexercise of its functions, and for the purpose
of complying with its obligations under the Government Information
(Public Access) Act 2009 and any other applicable legislation.
2. By executing this form, the signatory warrants that to the
extent that he/she is not the copyright owner of any documents
lodged with this application, Council is licensed by the copyright
owner to use the documents lodged with this application in
accordance with paragraph 1 above.
3. By executing this form, the signatory indemnifies Council
against all claims and actions in respect of a breach of copyright
arising from anyunauthorised use of any documents lodged with this
application.
OWNER'S DETAILS
Name: _::....:..H-=e.=....:C¥f 7 qr9("$'t:7 •
I/We the owner(s) of the property described in this application,
consent to its lodgment and hereby permit any duly authorised
officer of
Federation Council to enter the land or premises to carry out
inspections as required for the administration of the Act(s),
Regulations or
Planning Instrument.
Name (Print):
Name(Print): MCArc Vp-\-oA Capacity(Owne�Signature� Date·
All owners of the land to be developed must complete this
section. If the fond is owned by Crown Lond, on authorized officer
of the
relevant deportment must sign the opp/icotion. If you hove
recently purchased the fond, you must provide o Certificate of
Title or
Transfer Certificate showing transferor, transferee ond the
current Lot and DP number of the property. If the land is owned by
a private
company (P/L), the signature of at least one (1) director
residing in Australia is required. In the cose of a public company,
the
signatures of three (3) directors are required, two (2) of which
must reside in Australia.
21/3/19 Version 2 - 19/8532 � FEDERATION
� COUNCIL
-
FEDERATION COUNCIL
STATEMENT OF ENVIRONMENTAL EFFECTS
Standard form for minor developments only.
(:) 100 Edward Street Corowa NSW 2646 8 PO Box 77, Corowa NSW
2646 & (02) 6033 8999@ [email protected]
A COMPLETED STATEMENT OF ENVIRONMENTAL EFFECTS (SEE) IS REQUIRED
TO ACCOMPANY ALL DEVELOPMENT APPLICATIONS EXCEPT INTERGRATED
DEVELOPMENTS WHICH REQUIRE AN ENVIRONMENTAL IMPACT STATEMENT
(EIS}.
ABOUT THIS FORM: This SEE template is designed to form an
attachment to the Development Application. It can only be used for
the
following development types:
✓Dwellings, single storey in the Rl, R2, RUl, RUS and RS
zones.
✓single shops or commercial premises in the Bl, B2 & B6
zones*
✓Residential alterations and additions
✓ Ancillary residential buildings and structures such as,
verandahs, carports, garages, sheds, pergolas, swimming pools.
* Please note that a heritage impact statement is required for
all premises within the Heritage Conservation area. This will be
required for the majority of developments in the commercial
precinct of Corowa.
Developments not listed above may require a SEE with greater
detail. Please contact Council for further information.
The SEE must address all impacts that are relevant to your
proposal, with comment on how the development will control or
mitigate the
impact. No matter how minor the impact, please advise Council in
this document.
Failure to provide the requested items will delay processing of
the development application and may result in the application being
returned to you for completion or you receiving an additional
information request from Council.
APPLICANT'S DECLARATION: I/we declare to the best of my/our
knowledge and belief, at the p rticulars stated on this document
are correct in every detail and that the information required has
been supplied. 1/w acknowledge that the development application may
be returned to me if information is found to be missing or in
°'uate
/,
Applicant Signature: �� "_A � �---"�
Property Name:
Unit/House No.:
Town:
Lot:
/2-1¥
7 Section:
PROPOSED DEVELOPMENT
Street Name:
Postcode:
DP/SP:
Where applicable include a description of matters such as
proposed buildings, proposed building materials, nominated colour
scheme. Nature of use, staging
of the development, details of any demolition and other works to
be carried out in site.
;f/et,v cc/4 r 60.,1 L r4--
-
DESCRIPTION OF SITE
Include where applicable a description of the physical features
of the site such as shape, slope, vegetation, waterways.
flc. j t!!,JcrJ' /., ,·o /4...-. c�/ r-... 'c,/c-,---' NO If you
answered yes to any of the above please provide details and
justification for the proposal?
CREAllN OPPORTUNITY, ·' , 1 , ""llNl!Y
-
PRIVACY, VIEWS AND OVERSHADOWING
Will the development result in any privacy issues between
adjoining properties as a result of the
placement of windows, decks, pergolas, private open space
etc?
Will the development result in the overshadowing of adjoining
properties resulting in an adverse
impact on solar access?
Will the development result in any acoustic issues between
adjoining properties as a result of the
placement of active use outdoor areas, vehicular movement areas,
air conditioners, pump, bedroom
and living room windows etc?
Will the development impact on views enjoyed from adjoining or
nearby properties and public places
such as parks, road or footpaths?
If yes, please provide details of issue. Some issues will
require plans, i.e. overshadowing.
ACCESS, TRAFFIC AND UTILITIES
Is legal and practical access available to the development?
Will the development increase traffic movements/volumes?
If Yes by how much and what types of
Vehicles?
Are additional access points to a road network required?
Has vehicle maneuvering and onsite parking been addressed in the
design?
Is power, water, electricity, sewer and telecommunication
service readily available to the site?
Comments
r YES f.x- NO
r YES l_x NO
r YES P, NO
r YES ly NO
� YES r NO
r YES V NO
r YES !Y NO Jr YES r NO
¥ YES r NO
-- --- -- --- -- -- - - --- -- - --------------------
-------
ENVIRONMENTAL IMPACTS
Is the development likely to result in any form of air pollution
(smoke, dust odours etc?) r YES � NODoes the development have the
potential to result in any form of water pollution (i.e. sediment
from
r YES Ti( NO runoff)? Will the development have any noise
impacts above background noise levels? (i.e. air conditioner
r YES � NOunits, pool pumps)? Does the development involve any
significant excavation or filling? r YES � NOCould the development
cause erosion or sediment runoff (including during construction)? r
YES jy NOIs there a likelihood of the development resulting in site
contamination? r YES ry NOIs the development considered to be
environmentally sustainable (including provisions of BASIX
fY YES r NO certificate where required)?
Is the development situated in a heritage conservation area or
likely to have an impact on any r YES fS
-
FLORA AND FAUNA- FOR THREATENED SPECIES PLEASE VISIT
www.threatenedspecies.nsw.gov.au
Is the development likely to result in any form of air pollution
(smoke, dust odours etc?)
Will the development result in the removal of any native
vegetation from the site?
Is the development likely to have any impact on threatened
species or native habitat?
I YES
r YES
r YES
� NO
Jx' NO
� NO If the answer is yes to either of the above questions it
may be necessary to have a formal seven part test completed to
assess
the impact on threatened species - please contact Council for
further information.
Comments
WASTE AND STORMWATER DISPOSAL
How will effluent be disposed of Will liquid trade waste be
discharged to Council's sewer?
Will the Development result in any hazardous waste or other
waste disposal issue?
fy Sewer
r YES
I YES
r Septic
� NO
y NO How will stormwater (from roof and hard standing areas) be
disposed of? f)c--Council System r Other {Provide Details}
Details:
Have all potential overland stormwater risks been considered in
the design of the development? f YES r NO
Comments
SOCIAL AND ECONOMIC IMPACTS
Will the proposal have any economic or social consequences in
the area? Has the development addressed safety, security or crime
prevention issues?
Comments
r YES JX' YES
lz("' NO r NO
--- -
OTHER RELEVANT MATTERS
Are there any other matters for consideration that you are aware
of as developer?
;t/o
CREATING OPPORl UNITY . ' "UNI I Y
-
OTHER RELEVANT MATTERS {Continued)
LEGAL REFERENCES Section 78A(9) of the Environmental Planning
and Assessment Act 1979 states that the regulations may specify
what is required to be submitted with a development
application.
Section S0(l)(a) of the Environmental Planning and Assessment
Regulation 2000 states that development applications must contain
information and documents specified in schedule 1 part 1.
Schedule 1, part 1, subclause 2(1)(c) of the Environmental
Planning and Assessment Regulation 2000 requires the submission of
Statements of Environmental Effects (SEEs) with all development
applications ( other than complying and designed development).
Schedule 1, part 1, subclause 4 of the Environmental Planning
and Assessment Regulation 2000 states that such SEEs must show: •
The environmental impacts of the development• How the impacts have
been identified?• The steps to be taken to protect the environment
or lessen the expected harm to the Environment• Any matters
required to be indicated by any guidelines issued by the
Director-General.
The Applicant is advised that Council will make copies of
(including electronic copies) of the development application and
accompanying documents for the purpose of complying with its
obligations under the Environmental Planning and Assessment Act
1979 and the Local Government Act 1993. The applicant is
responsible for obtaining all copyright licenses necessary from the
copyright owners for this purpose.
PRIVACY STATEMENT: Information provided to Council may comprise
personal information as defined under the Privacy and Personal
Information Protection Act 1998. Personal information may be
utilised by Council to assess any application under the
Environmental Planning and Assessment Act 1979 and in accordance
with other legislation. Please note that personal information may
also be made available to third parties in accordance with the
Government Information (Public Access) Act 2009.
COPYRIGHT STATEMENT:
1. To the extent that the signatory to this form is the
copyright owner of documents lodged with this application, you
licenceCouncil to make all documents publicly available, and
further licence Council to reproduce and/or communicate all
suchdocuments for any purpose associated with the exercise of its
functions, and for the purpose of complying with its
obligationsunder the Government Information (Public Access) Act
2009 and any other applicable legislation.
2. By executing this form, the signatory warrants that to the
extent that he/she is not the copyright owner of any
documentslodged with this application, Council is licensed by the
copyright owner to use the documents lodged with this application
inaccordance with paragraph 1 above.
3. By executing this form, the signatory indemnifies Council
against all claims and actions in respect of a breach of
copyrightarising from any unauthorised use of any documents lodged
with this application.
CREATING OPPORl UNITY I , ' ".'UNI IY
Proposed Plans -shed - Industrial - 9-11 Headerworld Avenue
COROWA 2646 - Upton Enterprises Pty LtdApplication Form - - shed -
Industrial - 9-11 Headerworld Avenue COROWA 2646 - Upton
Enterprises Pty LtdStatement of Environmental Effects-- shed -
Industrial - 9-11 Headerworld Avenue COROWA 2646 - Upton
Enterprises Pty Ltd