This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
The 6N137, HCPL2601, HCPL2611 single-channel andHCPL2630, HCPL2631 dual-channel optocouplersconsist of a 850 nm AlGaAS LED, optically coupled to avery high speed integrated photo-detector logic gate witha strobable output. This output features an open collec-tor, thereby permitting wired OR outputs. The coupledparameters are guaranteed over the temperature rangeof -40°C to +85°C. A maximum input signal of 5mA willprovide a minimum output sink current of 13mA (fan outof 8).
An internal noise shield provides superior commonmode rejection of typically 10kV/µs. The HCPL2601 andHCPL2631 has a minimum CMR of 5kV/µs. TheHCPL2611 has a minimum CMR of 10kV/µs.
Schematics Package Outlines
8
1
8
1
8
1
A 0.1µF bypass capacitor must be connected between pins 8 and 5(1).
= 25°C unless otherwise specified)Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.The absolute maximum ratings are stress ratings only.
*For peak soldering reflow, please refer to the Reflow Profile on page 11.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings.
*6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0mA or less.
Symbol Parameter Value Units
T
STG
Storage Temperature -55 to +125 °C
T
OPR
Operating Temperature -40 to +85 °C
T
SOL
Lead Solder Temperature (for wave soldering only)* 260 for 10 sec °C
Transfer Characteristics (TA = -40 to +85°C unless otherwise specified)
Isolation Characteristics (TA = -40°C to +85°C unless otherwise specified.)
*All Typicals at VCC = 5V, TA = 25°C
Notes: 1. The VCC
supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC
and GND pins of each device.
2. Each channel.
3. Enable Input – No pull up resistor required as the device has an internal pull up resistor.
4. tPLH – Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current
pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
5. tPHL – Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current
pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
6. tr – Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
7. tf – Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
8. tELH – Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input
voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.
9. tEHL – Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input
voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.
10. CMH – The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
HIGH state (i.e., VOUT > 2.0V). Measured in volts per microsecond (V/µs).
11. CML – The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
LOW output state (i.e., VOUT < 0.8V). Measured in volts per microsecond (V/µs).
12. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and 8 shorted together.
Symbol DC Characteristics Test Conditions Min. Typ.* Max. Unit
IOH HIGH Level Output Current VCC = 5.5V, VO = 5.5V,IF = 250µA, VE = 2.0V(2)
100 µA
VOL LOW Level Output Current VCC = 5.5V, IF = 5mA, VE = 2.0V, ICL = 13mA(2)
.35 0.6 V
IFT Input Threshold Current VCC = 5.5V, VO = 0.6V, VE = 2.0V, IOL = 13mA
3 5 mA
Symbol Characteristics Test Conditions Min. Typ.* Max. Unit
• Peak reflow temperature: 225 C (package surface temperature) • Time of temperature higher than 183 C for 60–150 seconds • One time soldering reflow is recommended
TRADEMARKSThe following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is notintended to be an exhaustive list of all such trademarks.
AccuPower™Auto-SPM™Build it Now™CorePLUS™CorePOWER™CROSSVOLT™CTL™Current Transfer Logic™DEUXPEED®
Dual Cool™EcoSPARK®
EfficientMax™ESBC™
®
Fairchild®
Fairchild Semiconductor®
FACT Quiet Series™FACT®
FAST®
FastvCore™FETBench™FlashWriter®*FPS™
F-PFS™FRFET®
Global Power ResourceSM
Green FPS™Green FPS™ e-Series™Gmax™GTO™IntelliMAX™ISOPLANAR™MegaBuck™MICROCOUPLER™MicroFET™MicroPak™MicroPak2™MillerDrive™MotionMax™Motion-SPM™OptoHiT™OPTOLOGIC®
OPTOPLANAR®
®
PDP SPM™Power-SPM™
PowerTrench®
PowerXS™Programmable Active Droop™QFET®
QS™Quiet Series™RapidConfigure™
™
Saving our world, 1mW/W/kW at a time™SignalWise™SmartMax™SMART START™SPM®
* Trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMERFAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVERELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT ORCIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESESPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILDíS WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICYFAIRCHILDíS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THEEXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:1. Life support devices or systems are devices or systems which, (a) are
intended for surgical implant into the body or (b) support or sustain life,and (c) whose failure to perform when properly used in accordancewith instructions for use provided in the labeling, can be reasonablyexpected to result in a significant injury of the user.
2. A critical component in any component of a life support, device, orsystem whose failure to perform can be reasonably expected tocause the failure of the life support device or system, or to affect itssafety or effectiveness.
ANTI-COUNTERFEITING POLICYFairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts.Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications,and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation ofcounterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who arelisted by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, havefull traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information.Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provideany warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage ourcustomers to do their part in stopping this practice by buying direct or from authorized distributors.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification Product Status Definition
Advance Information Formative / In DesignDatasheet contains the design specifications for product development. Specifications may change inany manner without notice.
Preliminary First ProductionDatasheet contains preliminary data; supplementary data will be published at a later date. FairchildSemiconductor reserves the right to make changes at any time without notice to improve design.
No Identification Needed Full ProductionDatasheet contains final specifications. Fairchild Semiconductor reserves the right to make changesat any time without notice to improve the design.
Obsolete Not In ProductionDatasheet contains specifications on a product that is discontinued by Fairchild Semiconductor.The datasheet is for reference information only.