Simba 1354

8/10/2019 Simba 1354

http://slidepdf.com/reader/full/simba-1354 1/4

Atlas Copco

Technical specification

Simba 364-ITH

Production drilling rigs

Standard features

»ITH-hammerPneumatic in the hole hammer, ITH (hammer not•supplied with rig)Rotation unit DHR 6•

Drilling unit»

Mechanized rod handling system•Feed with hydraulic two-stage cylinder •Front- and rear-mounted stingers•Breakout table for guidance during collaring and•as support during rod handling

Positioning unit»Tilt, rotation, pendulum arm and slide table•Accurate and smooth movements•Mine-adapted, sturdy components•

Control system»Electrical Direct System (EDS)•Anti-jamming system•

Carrier»Mine-adapted carrier for small- to medium-sized drifts with•

articulated steering and four-wheel drive

General»Trolley-mounted operator panel•FOPS-approved protective roof •Electrical cable reel•Working lights on tripods•

Production drilling rig with pneumatic in the hole hammer, ITH, fordeep straight holes. Ring drilling with parallel holes upwards/down-wards up to 3 m apart. Hole diameter 90–178 mm.

8/10/2019 Simba 1354


Simba 364-ITH

Specifications

ROTATION UNIT

DHR 6H

56

DHR 6H

68

Length with fixed adapter 530 mm

Length with floating adapter 840 mm

Torque, max. 6 000 Nm

Rotation speed 0–107 rpm 0–68 rpm

Adapter fixed API 23

/8’’ or API 3½ ’’ Reg femAdapter floating FLT API 23 /8’’ or 3 ½’’ Reg femWeight with/without floating sub 243/182 kg

Power pack»

Hydraulic pump for rotation, positioning, feed•Pumps unloaded at start•

System pressure, max• .................................................. 250 bar Hydraulic oil tank, volume max/min• .............................. 160 lLow oil level indicator •Oil temperature gauge on oil tank •Electrical oil flling pump•Filtration, absolute• ......................................................... 16 μmOil flter indicator •Water cooled oil cooler in stainless steel•Mineral hydraulic oil•

Drilling unit»

Rod Handling System, RHS 27• ..............................27+1 pipesAdaptable to 5′ and 6′ pipes•Adaptable to 76 and 89 mm drill pipes•Mechanized drilling up to 51 m•

FEED

BMH 200-series BMH 235 BMH 236

Total length 3 200 mm 3 510 mm

Drill steel length 1 500 mm 1 800 mm

Total length with extractor 3 500 mm 3 810 mm

Positioning system»

Feed extension (with 4′ drill pipe)• ............................. 900 mmFeed extension (with 5′ and 6′ drill pipe)• ................ 1 200 mmRotary Acurator BHR 60–2 for 360º ring drilling•Sliding table BHT 150 gives 1.5 m feed parallel positioning•Pendulum arm, BHP 150 gives 1.5 m feed parallel positioning•in the side walls. Adds additional 1.5 m feed parallel position-ing upwards/downwards.

Stinger backward on feed• .......................................BSJ 8-200Stinger forward on feed• ..........................................BSJ 8-115Feed dump, drilling• ..............+20º forward and -65º backward

Carrier»

Deutz 4-cylinder D914 L04, EPA III/COM III (Tier 3/Stage•IIIA) approved 4-stroke prechamber diesel engine

Power rating at 2 300 rpm• ................................ 55 kW (75 hp)Torque at 1 550 rpm• ...................................................230 NmFixed seat for tramming, including safety belt•Articulated steering• .................................. ±41° steering angleFour-wheel drive•FOPS-approved protective roof •Hydrostatic power steering system•Hydrodynamic transmission• .................................Clark 12000Front axle• ................................................................ Dana 176Rear axle• .......................................... Dana 176, ±8º oscillationAutomatic differential lock on front axle, limited slip•Tyres• .....................................................................12.00 x R20Clearence outside axles• ...................................................... 15ºHydraulic jacks, front• .......................................... 2 extendableHydraulic jacks, rear • ..............................................................2Service brakes• 2 separate circuits (hydraulically applied, fullyenclosed wet disc brakes)Emergency and parking brakes• .....................................SAHR Fuel tank, volume• .............................................................. 60 lElectric system• .................................................................24 VBatteries• ....................................................................2 x 70 AhTramming lights• ........................................................8 x 70 WBrake lights•Illuminated stairs for platform•Central lubrication system•Silencer and catalyser •Fire extinguisher •Spirit levels•Gradeability at max load on drive wheels• .......................... 1:4

Tramming speed on at ground• ............................... >10 km/hTramming speed on incline 1:8• .................................. >4 km/hHorn, beacon and reverse alarm•Outlet for communication radio• .......................................12 V

Electrical system»

Total installed power • .....................................................65 kWMain motor at 50 Hz• .....................................................55 kWVoltage• .................................................................380–1 000 VFrequency• .................................................................50–60 HzStarting method• .........star/delta (380–690 V) direct (1 000 V)Thermal overload protection for electric motors•Percussion hour meters on A-panel•Digital volt/amperage meter in electric cabinet•Phase sequence indicator •Earth fault indicator •Battery charger •Transformer • ....................................................................4 kVACable reel•Limit switch for cable reel•Working lights on tripods• ...............................2 x 200 W, 24 V

Water system»

Water injection pump•Capacity• .............................................................. max 50 l/minMin water inlet pressure• .................................................. 2 bar Hydraulic drive, axial piston motor• ............................... 10 ccWater pressure gauge•

2-inch system•High and low percussion•HECL lubrication system with electric flling pump•

Air pressure gauge and air ow gauge•

Air system»

Control system»

Electrical Direct System, EDS•Basic functions such as semi-automatic drilling and anti-jam-•ming included

8/10/2019 Simba 1354


Simba 364-ITH

Specifications

Optional equipment

Drilling system»ITH lubrication surveillance system•Floating sub•

Positioning system»Rig alignment laser RAL 650•Additional stinger backward on feed, BSJ 8-200 (stroke•length 2 000 mmAutomatic lubrication for positioning/drilling system•Central lubrication for positioning/drilling system•Thread lubrication kit•Angle reading instrument (ARI 6 C), with or without hole•depth measurement

Power pack»Heater kit•

Electrical system»Electrical cable on reel, H07RN-F•Electrical cable on reel, Buex•Plug PC4/PC5•Socket PC4/PC5•Switch gear •Working lights on tripods, 2 x 500 W, 230 V•Electrics according to local standards•

Carrier»Fire suppression system ANSUL, manual•Manual spotlight•

Miscellaneous»Manual rig washing kit•Manual lubrication kit• Ni-Cr plated piston rods•

DRILL STRING

ITH-hammer Hole diameter, mm Drill pipes, mm Pipe length, mm Thread pin/box

COP 34 90–105 76 1 800 2 3/8” API Reg

COP 44 105–130 89 1 500/1 800 2 3/8” API Reg

COP 54 GE 130–152 89 1 500/1 800 2 3/8” API Reg

COP 64 Gold 156–178 114 1 500 3 1/2” API Reg

8/10/2019 Simba 1354


Simba 364-ITH

9 8 5 1 2

5 5 5

0 1 a

1 1 / 2 0 0 8

© C

o p y r i g h t 2 0 0 8 ,

A t l a s

C o p c o R o c k D r i l l s A B ,

Ö r e b r o ,

S w e d e n .

A l l p r o d u c t n a m e s i n t h i s p u b l i c a t i o n a r e t r a d e m a r k s o f A t l a s C o p c o .

A n y u n a u t h o r i z e d u s e o r c o p

y i n g o f t h e c o n t e n t s o r a n y p a r t t h e r e o f i s p r o h i b i t e d .

I l l u s t r a t i o n s a n

d p h o t o s

m a y s h o w e q u i p m e n t w

i t h o p t i o n a l e x t r a s .

N o w a r r a n t y i s m a d e r e g a r d i n g s p e c i fi c a t i o n s o r o t h e r w i s e .

S p e c i fi c a t i o n s a n d e q u i p m e n t a r e s u b j e c t t o c h a n g e w i t h o

u t n o t i c e .

C o n s u l t y o u r A t l a s C o p c o C u s t o m e r C e n t e r f o r s p e c i fi c i n f o

r m a t i o n .

Measurements

COVERAGE AREA

SIDE VIEW

DIMENSIONS

mm Width 1 950

Height tramming 3 180

Height roof up 2 960

Length tramming (with BHM 234) 8 362

Ground clearance 280

WEIGHT

gross weight

kg Total (basic rig+RHS) 15 500

Boom side 11 000

Engine side 4 500

RECOMMENDED CABLE SIZE AND LENGTH

Voltage Type Dimension, mm2 Diameter,

mm

Length,

m

EDS 18

380–400 V RDOT 4x50 mm2 44 mm 65 m

380–400 V Buflex 3x70+3G16 mm2 37 mm 95 m

440–575 V RDOT 4x35 mm2 38 mm 95 m

440–575 V Buflex 3x50+3G10 mm2 32 mm 140 m

660–700 V RDOT 4x25 mm2 34 mm 115 m

660–700 V Buflex 3x35+3G6 mm2 28 mm 185 m

1 000 V Buflex 3x35+3G6 mm2 28 mm 185 m

G = Protection yellow/green Recommendations are given for surrounding temperature of 40 °C.

TURNING RADIUS

depending on surface

mm Outer 5 440

Inner 2 890

7 0 0

1 8 4 5

2 2 6 0

3 1 8 0

2310150015552304

8763 (with BMH 264)

20º65º

2 5 5

45º

750750

2380

2430

1950

1500

2 0 0 0

45º

9 4 5

1 1 5 0

Simba 1354

Documents