SIKA PLASTIC ADHESIVE SUPERFAST BONDING OF PLASTIC PARTS Plastic Primer 5 min 4 Spray a thin coat of Plastic Primer on both sides, flash-off for 5 min 1) 80 2 Grind a V-groove (1 cm approx.) into the side edges, use 80 grit sandpaper 8 Fill up the break with adhesive Sika Services AG / Industry / Aftermarket / Sika Plastic Adhesive Superfast / TZ / 09.2016 Our most current General Sales Conditions shall apply. Please consult our most current local Data Sheet prior to any use or processing. www.sika.com/aftermarket Open Time PLASTIC ADHESIVE SUPERFAST SikaPower®-2955 Article No. 505390 Open Time (23°C) 90 sec Sanding Time (23°C) 10 min Content 50 ml + 3 mixers Mixing Ratio 1:1 Color Black ACCESSORIES Article No. Content Box Content Sika® Cleaner G+P 527420 500 ml trigger spray 12 pc SikaPower® -2900 Primer 505295 200 ml aerosol 6 pc Sika Contouring Film 505296 360 cm 30 pc Sika Reinforce- ment Film 505297 360 cm 20 pc Sika Mixer Quadro 505298 12 pc / bag 20 bags Sika Dispensing gun 512113 – 1 3 Clean entire work area using Sika® Cleaner G+P, making sure the surface is completely dry and no moisture remains 9 Bend the film and compress adhesive and wait for adhesive to be cured according to product label 1) All time indications are related to 23°C (ambient and subst- rate). Product curing behavior is temperature dependent and increases with higher temperature and vice versa. Cure time may be accelerated by applying heat up to 85°C using infrared lamps, heating blankets or ovens. Consult curing information on product label or contact Sika Technical Service. 5 Before attaching mixer, extrude some material until both parts A and B flow evenly Attach static mixer and dispense a small amount of adhesive 1 Damage: a broken piece of plastic 7 Fix both parts 6 Position one part on the Sika Contouring Film and apply Plastic Adhesive Superfast on the breaking point
4
Embed
Sika Plastic Adhesive Superfast - Industry · 2020. 10. 1. · Sika Services AG / Industry / Aftermarket / Sika Plastic Adhesive Superfast Sika Reinforce-/ TZ / 09.2016 ... ACCESSORIES
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
SIKA PLASTIC ADHESIVE SUPERFAST BONDING OF PLASTIC PARTS
Plastic Primer
5 min
4
� Spray a thin coat of Plastic Primer on both sides, flash-off for 5 min1)
802
� Grind a V-groove (1 cm approx.) into the side edges, use 80 grit sandpaper
8
� Fill up the break with adhesive
Sika
Ser
vice
s A
G /
Indu
stry
/ A
fter
mar
ket /
Sik
a Pl
asti
c A
dhes
ive
Supe
rfas
t / T
Z /
09.2
016
Our most current General Sales Conditions shall apply. Please consult our most current local Data Sheet prior to any use or processing.
www.sika.com/aftermarket
Open Time
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
Article No. 505390
Open Time (23°C) 90 sec
Sanding Time (23°C) 10 min
Content 50 ml + 3 mixers
Mixing Ratio 1:1
Color Black
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
ACCESSORIES Article No.
Content Box Content
Sika® Cleaner G+P 527420500 ml trigger spray
12 pc
SikaPower®-2900 Primer 505295 200 ml
aerosol 6 pc
Sika Contouring Film 505296 360 cm 30 pc
Sika Reinforce-ment Film 505297 360 cm 20 pc
Sika Mixer Quadro 505298 12 pc / bag 20 bags
Sika Dispensing gun 512113 – 1
3
� Clean entire work area using Sika® Cleaner G+P, making sure the surface is completely dry and no moisture remains
9
� Bend the film and compress adhesive and wait for adhesive to be cured according to product label
1) All time indications are related to 23°C (ambient and subst-rate). Product curing behavior is temperature dependent and increases with higher temperature and vice versa. Cure time may be accelerated by applying heat up to 85°C using infrared lamps, heating blankets or ovens. Consult curing information on product label or contact Sika Technical Service.
5
� Before attaching mixer, extrude some material until both parts A and B flow evenly
� Attach static mixer and dispense a small amount of adhesive
1
� Damage: a broken piece of plastic
7
� Fix both parts
6
� Position one part on the Sika Contouring Film and apply Plastic Adhesive Superfast on the breaking point
SIKA PLASTIC ADHESIVE FASTBUMPER AND PLASTIC REPAIR
PLASTIC ADHESIVE FAST SikaPower®-2950
Article No. 505377
Open Time (23°C) 3.5 min
Sanding Time (23°C) 30 min
Content 50 ml + 3 mixers
Mixing Ratio 1:1
Color Black
PLASTIC ADHESIVE FAST SikaPower®-2950
ACCESSORIES Article No.
Content Box Content
Sika® Cleaner G+P 527420500 ml trigger spray
12 pc
SikaPower®-2900 Primer 505295 200 ml
aerosol 6 pc
Sika Contouring Film 505296 360 cm 30 pc
Sika Reinforce-ment Film 505297 360 cm 20 pc
Sika Mixer Quadro 505298 12 pc / bag 20 bags
Sika Dispensing gun 512113 – 1
1
� Rinse plastic part with high pressure
8
� Apply Plastic Adhesive Fast around the crack to the backside of the part
2
� Crack: Drill hole with a V-cut at the end of the crack
� Hole: Drill few holes with V-neck around the damage
9
� Position the pre-cut reinforcement film into the applied adhesive
803
� On the front side grind a V-groove (1 cm approx.) into the side edges, use 80 grit sandpaper for grinding
10
� Apply the adhesive bubble-free on top of the reinforcement film until it is completely covered
180
4
� Roughen the surfaces on the front and back sides with 180 grit sandpaper
11
� Spread from the adhesive using the Sika Contouring Film from the middle to the edges to avoid bubbling
5
� Clean entire work area using Sika® Cleaner G+P, making sure the surface is completely dry and no moisture remains
12
� Fill the damaged area on the front side of the part with adhesive
Plastic Primer
5 min
6
� Spray a thin coat of Plastic Primer on both sides, flash-off for 5 min1)
13
� Spread from the adhesive using the Sika Contouring Film
� Respect curing time1) as per product label
7
� Before attaching mixer, extrude some material until both parts A and B flow evenly
� Attach static mixer and dispense a small amount of adhesive
18014
� Sand the surface and proceed with filling and painting
Sika
Ser
vice
s A
G /
Indu
stry
/ A
fter
mar
ket /
Sik
a Pl
asti
c A
dhes
ive
Fast
/ T
Z /
09.2
016
Our most current General Sales Conditions shall apply. Please consult our most current local Data Sheet prior to any use or processing.
www.sika.com/aftermarket
1) All time indications are related to 23°C (ambient and substrate). Product curing behavior is temperature dependent and increases with higher temperature and vice versa. Cure time may be accelerated by applying heat up to 85°C using infrared lamps, heating blankets or ovens. Consult curing information on product label or contact Sika Technical Service.
Open Time
SIKA PLASTIC ADHESIVE SUPERFASTRE-SHAPE AND MODEL PLASTIC CLIPS
6
� Draw the shape of the clip and bonding-areas on the Sika Contouring Film
2
� Drill few holes with V-Neck
8
� Apply Plastic Adhesive Superfast within the prefigured area
180
3
� Sand the area around the broken clip use 180 grit sandpaper
9
� Press adhesive on the backside of the area and bend it in the middle
4
� Clean entire work area using Sika® Cleaner G+P, making sure the surface is completely dry and no moisture remains
10 min
10
� Press other side on the top and wait for curing
Plastic Prim
er
5 min
5
� Spray a thin coat of Plastic Primer on both sides, flash-off for 5 min1)
11
� After curing, cut the new clip to required shape
Sika
Ser
vice
s A
G /
Indu
stry
/ A
fter
mar
ket /
Sik
a Pl
asti
c A
dhes
ive
Supe
rfas
t / T
Z /
09.2
016
1) All time indications are related to 23°C (ambient and subst-rate). Product curing behavior is temperature dependent and increases with higher temperature and vice versa. Cure time may be accelerated by applying heat up to 85°C using infrared lamps, heating blankets or ovens. Consult curing information on product label or contact Sika Technical Service.
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
Article No. 505390
Open Time (23°C) 90 sec
Sanding Time (23°C) 10 min
Content 50 ml + 3 mixers
Mixing Ratio 1:1
Color Black
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
ACCESSORIES Article No.
Content Box Content
Sika® Cleaner G+P 527420500 ml trigger spray
12 pc
SikaPower®-2900 Primer 505295 200 ml
aerosol 6 pc
Sika Contouring Film 505296 360 cm 30 pc
Sika Reinforce-ment Film 505297 360 cm 20 pc
Sika Mixer Quadro 505298 12 pc / bag 20 bags
Sika Dispensing gun 512113 – 1
1
� Damage: a broken plastic clip
7
� Before attaching mixer, extrude some material until both parts A and B flow evenly
� Attach static mixer and dispense a small amount of adhesive
Open Time
Our most current General Sales Conditions shall apply. Please consult our most current local Data Sheet prior to any use or processing.
www.sika.com/aftermarket
SIKA PLASTIC ADHESIVE SUPERFAST RE-BUILD A BROKEN EYELET
80
2
� Sand the edges, use 80 grit sandpaper for grinding
3
� Clean entire work area using Sika® Cleaner G+P, making sure the surface is completely dry and no moisture remains
Plas
tic P
rimer
5 min
4
� Spray a thin coat of Plastic Primer on both sides, flash-off for 5 min1)
5
� Put some tape behind the gap to be bridged
7
� Fill the gap with Plastic Adhesive Superfast
1
� Damage: a broken eyelet
8
� Compress tape and adhesive and wait for adhesive to be cured1) according to product label
Sika
Ser
vice
s A
G /
Indu
stry
/ A
fter
mar
ket /
Sik
a Pl
asti
c A
dhes
ive
Supe
rfas
t / T
Z /
09.2
016
1) All time indications are related to 23°C (ambient and substrate). Product curing behavior is temperature dependent and increases with higher temperature and vice versa. Cure time may be accelerated by applying heat up to 85°C using infrared lamps, heating blankets or ovens. Consult curing information on product label or contact Sika Technical Service.
Sika
Ser
vice
s A
G /
Indu
stry
/ A
fter
mar
ket /
Sik
a Pl
asti
c A
dhes
ive
Supe
rfas
t / T
Z /
09.2
016
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
Article No. 505390
Open Time (23°C) 90 sec
Sanding Time (23°C) 10 min
Content 50 ml + 3 mixers
Mixing Ratio 1:1
Color Black
Compress tape and adhesive and wait for adhesive to be cured1) according to product label
PLASTIC ADHESIVE SUPERFAST SikaPower®-2955
ACCESSORIES Article No.
Content Box Content
Sika® Cleaner G+P 527420500 ml trigger spray
12 pc
SikaPower®-2900 Primer 505295 200 ml
aerosol 6 pc
Sika Contouring Film 505296 360 cm 30 pc
Sika Reinforce-ment Film 505297 360 cm 20 pc
Sika Mixer Quadro 505298 12 pc / bag 20 bags
Sika Dispensing gun 512113 – 1
6
� Before attaching mixer, extrude some material until both parts A and B flow evenly
� Attach static mixer and dispense a small amount of adhesive
Open Time
Our most current General Sales Conditions shall apply. Please consult our most current local Data Sheet prior to any use or processing.